Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
AMT Inline Circulator Pumps are designed for continuous duty industrial/ commercial systems. Pumps are available in a variety ofmaterial configurations to meet your specifications. All models are powered by a single phase 115 VAC ODP 56J NEMA frame 1/4 HP electric motor with 1/2-14 NPSM conduit connection. Direct coupled design eliminates stub shaft, oiled bearing and coupling, reducing maintenance. Pumps are interchangeable with other manufacturers, see cross reference on specification page.
* Maximum temperature applies to water only.
816141210186420
0
2
4
6
8
01
21
41
61
81
02
065505540453035202510150
eziS egnalF mumixaM no desaB
)zH 06( MPR 5271 @ yticapaC0.1 ytivarg cificeps retaW- diuqiL 13.2 yb edivid ,isp ot trevnoC)*(
]Wk 91.0[ PH 4/1 seireS 965 = A]Wk 91.0[ PH 4/1 seireS 075 = B]Wk 91.0[ PH 4/1 seireS 175 = C]Wk 91.0[ PH 4/1 seireS 275 = D
0
1
2
3
4
]*.tf[ ]m[
]mpg .S.U[
To
tal H
ead
m[ 3 ]h/
D
C
B
A
®
A Gorman-Rupp Company
INLI
NE
CIR
CU
LATO
R P
UM
PS
HVM-7
400 Spring Street • Royersford, PA 19468 USA
www.amtpump.com • 888-amt-pump (268-7867)For use with nonflammable liquids compatible with pump component materials. Viton® and Teflon® are registered trademarks of E. I. Dupont.
Inline Centrifugal Circulator Pumps • Cast Iron or Silicon Bronze
Construction
• EPDM/EPR Mechanical Seal and Casing O-ring, Buna-N Option Available
• Investment Cast Stainless Steel Impeller with 569/570/571 Series, 572 Series Includes Silicon Bronze Impeller
• Accessory Mounting Flanges Available 3/4˝ to 2˝ NPT
• Maximum Temperature 225° F (107º C)*
• Maximum Flow 58 GPM
• Maximum Head 19 Ft. (8 PSI)
• Single Phase 1/4 HP, 1725 RPM, 115 VAC ODP 56J Motor with Overload Protection
Bronze Circulator Pump
Performance of Inline Circulator Pumps
Pump Dimensional & Specification Data
Flange Face to NPT3/4'' 1'' 1-1/4'' 1-1/2'' 2'' Face ThicknessModel Series
C569-90 C569-91 C569-92 N/A N/A 3/4''C569-93 C569-94 C569-95 N/A N/A 3/4''C570-90 C570-91 C570-92 C570-93 N/A 3/4''C570-94 C570-95 C570-96 C570-97 N/A 3/4''
N/A N/A N/A N/A C570-98 1-1/2''N/A N/A N/A N/A C570-99 1-1/2''
Connection Flanges - Flange Kit Model NumbersFlanges Available - Standard NPT (Female) Pipe Thread
NOTE: NPT Flange Kits Include:2 Flanges, 2 Buna-N Gaskets, 4 Bolts and Nuts
W Dimension Refers to Flange to Flange Width
Flange to Bell & Gossett Armstrong TACO DaytonFlange Width* Series Series Series (Cast Iron)
569 6.4 100NFI S-25 110 4RD16570 8.5 HV NFI H-32 111 4RC93571 8.5 PR H-41 113 4RC91572 8.5 2NFI S-35 120 4RC95
Manufacturer Cross Reference
*Refers to B Dimensions
**This dimension may vary due to motor manufacturer specificationsNOTE: Dimensions are in inches (centimeters) and have a tolerance of ± 1/8".NOTE: Electric supply for ALL motors must be within ± 10% of nameplate voltage rating (e.g. 230V ± 10% = 207 to 253.)
569/570/571 Series – Stainless Steel Impeller572 series – Bronze Impeller
ModelSeries
569 Series XCI569 Series XB
570 & 571 series XCI570 & 571 series XB572 Series XCI (-95)572 Series XCI (-97)
‡ When ordering add the correct -9x suffix to model number indicating material selectionXCI (-95) = Cast Iron ConstructionXB (-97) = Cast Bronze Construction
PUMPS AREDESIGNED TO MOUNT
HORIZONTALLYOR VERTICALLY
Model ‡ Curve HP PH ENC A B C W H**
5690 A
1/4 1 ODP 115
2.1 [5.3] 3.1 [7.9] 3.1 [7.9] 6.3 [16.0] 13.3 [33.8] 25
5710 C 2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3] 28
5720 D 2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3] 28
5.4
‡ Ship Wt.(Lbs.)
Voltage@ 60 Hz
Full LoadAmps
5700 B 2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3] 28
®
A Gorman-Rupp Company
®
A Gorman-Rupp Company
Manufacturer of AMT & IPT Pumps400 Spring Street • Royersford, PA 19468 USA
www.amtpump.com • 888-amt-pump (268-7867)The Gorman-Rupp Company reserves the right to discontinue any model or change specifications at any time without incurring any obligation.
©2012 American Machine and Tool Company. All rights reserved.
Inline Centrifugal Circulator Pumps
• 4-Bolt Flange Allows 360° Mounting Rotation in 90° Increments
• 1/8" NPT Seal Wash/Vent Port Shipped Plugged
• EPDM/EPR Mechanical Seals and O-Rings
• Optional Buna-N Mechanical Seal and O-Ring Available
• Close Coupled Design Reduces Maintenance Requirements
• Standard NEMA 56J Motor Mounting Dimensions
• Stainless Steel (300 Series) Motor Shaft
• High Efficiency Closed Impeller
• Inline Centered Design, Centerline of Ports In Line with Motor Shaft
• Maximum Working Pressure 150 PSI
• QSP: Quick Ship Pump for Many Models
Standard Features
HVM-8
12120220