INDIAN INSTITUTE OF TECHNOLOGY KANPUR Tender Notice No. … · 3.1.1 3.5C x 150 SQMM Armoured AL Cable 200.00 RM ... CABLE 100.00 RM 3.2.4 3C x 16 SQMM PVC INS. PVC SH. FRLS CU. FLEX

S. No Description of Items Qty Unit Rate in Figures

in Rupees

Amount

1. CABLE LAYING IN HUME PIPE & MANHOLE

1.1 Providing, laying and fixing following dia RCC pipe

NP2 class (light duty) in ground complete with RCC

collars, jointing with cement mortar 1:2 (1 cement : 2

fine sand) including trenching (75 cm deep) and

refilling etc as required.

1.1.1 450 mm dia 5.00 RM

1.1.2 300 mm dia 30.00 RM

1.1.3 100 mm dia. 10.00 RM

1.2 Providing & making of MAN HOLE chambers of

various sizes as detailed below with 230/ 345 mm

thick brick work plaster inside and outside both, PCC

flooring including providing and fixing of heavy duty

ISI mark SFRC cover with frame complete with RCC

slab and as approved by the Engineer.

1.2.1 450mm X 450 mm (depth 0.700 mtr) - 230mm Thick 1.00 Nos

1.2.2 750mm X 750 mm (depth 0.900mtr) - 230mm Thick 1.00 Nos

1.2.3 1200mm X 1000 mm (depth 1.0mtr) - 230mm Thick 1.00 Nos

2 LT PANELS, SWITCHGEARS AND METERS

Defination : LT Panels are used for LT power

distribution to all Distribution Boards / Sub

Panels.This section covers the following items

INDIAN INSTITUTE OF TECHNOLOGY KANPUR

Tender Notice No. 63 /Elect/2019

SCHEDULE OF QUANTITY

Name of the Contractor

Name of Work: Construction of 5th, 6th, 7th & 8th floor of National Aerosol Facility Building Phase-II (SH:

Electrical Works).


in Rupees

Amount

2.1 Design , fabrication, wiring, Supply, Installation,

Testing and Commissioning of following Wall

mounted / Floor mounted(including base stand),

415V,3PH, 50Hz extensible and fully

compartmentalized panels complying to IS 8623/93.

The indoor panels shall be IP 42 and outdoor panels

shall be IP 54 type.The Panel shall have proper space

with required clearance for cables, incoming /

outgoing switchgear, CTs, PTs, Ammeter, Voltmeter,

selector switches, Insulated and properly supported

compartmentalized bus bars with heat shrinkable

sleeves along with the other control circuit

accessories within the panel and any other electrical

component mentioned in the Panel SLD.The panel

shall be fabricated out of CRCA not less than 2.0 mm

thick for load bearing members and 1.6mm for the

doors of LT panel.The Panel shall have seven tank pre

treatment process comprising of degreasing, rinsing,

de-rusting, rinsing, phosphatising, rinsing and

passivation followed by powder coat painting having

a paint thickness of 60 microns or as specified.The

Panel shall be Dust/Vermin poof with earth studs as

per

2.1.1 LNP (Lighting Distribution Panel) :

Incomer : 1 Nos. x 2kVp, 50kA, Surge arrestor

Incomer : 1 Nos. x 250 A, Four pole , MCCB, 25kA,

Microprocessor based

Incomer : 1 set. x R,Y,B indication lamp with 2A

control MCB

Incomer : 1 Nos. x Multi Function meter

Incomer : 3 Nos. x CT 250/5A, CL:1, 15VA, Ring type

Bus bar : 1 set. x 415V, 50HZ, 300 A, Four pole , 25kA

aluminium busbar.

Outgoing : 2 Nos. x 100 A, Four pole , MCCB, 25kA,

Microprocessor based

Outgoing : 2 Nos. x 40 A, TPN, MCB, B type,10kA

Outgoing : 2 Nos. x 25 A, TPN , MCB, B type,10kA

Outgoing : 2 Nos. x 32 A, Double pole , MCB, B

type,10kA

Outgoing : 3 sets. x R,G On-Off lamp with 2A control

MCB

5.00 Nos


in Rupees

Amount

2.2 Supplying and fixing following rating, Dual Pole / four

pole, (three phase and neutral), 230/415 volts, MCB,

quick make and break type with connections, testing

and commissioning etc. as required.

2.2.1 16 Amp, FP MCB , 10kA, C Type (For Air washer) 1.00 Each

2.2.2 25 Amp, FP MCB , 10kA, C Type (For Air washers) 3.00 Each

2.2.3 40 Amp, FP MCCB , 10kA, C type (For 10KVA UPS) 1.00 Each

2.3 S & F metal enclosure suitable for DP/FP MCB/ on

surface or recessed etc as reqd.

5.00 Each

2.4 Supplying and fixing 25Amp rating, Four pole, (Three

phase and neutral), 415 volts, residual current break

over circuit breaker (RCBO), having a sensitivity

current upto 300 milliamperes and breaking capacity

of 10kA in an enclosure complete with connections,

testing and commissioning etc. as required.

1.00 Nos

SAFETY TOOLS & EQUIPMENTS

2.5 Providing & fixing in position 1000 mm wide ,

Electrical Insulating Mats as per IS 15652:2006, 2mm

thick, suitable upto 3.3 KV , fire retardant,no effect of

acids, alkalies and transformer oils, moisture proof,

high tensile strength and texture finish / cloth

impression (Anti slip , marking on top)

10.00 SqM

2.6 Supply & fixing in position approved shock treatment

chart written in English Hindi and Local language.

These charts shall be framed in wooden frame &

covered with clear glass.

3.00 Nos.

3 CABLES, END TERMINATIONS

Defination : The item in this section refers to

incoming and outgoing cabling of sub Panels and

outgoing cabling of main panel along with its end

termination requirements.


in Rupees

Amount

3.1 Supply of following armoured/Unarmoured/flexible

cables from main panel to sub panels and from sub

panels to final DBs. All the below mentioned cables

shall be 1.1kV grade, XLPE insulated, FRLS type

armoured cables of Al / Cu, whichever applicable

with inner and outer PVC sheath.The said cables shall

confirm IS 7098-1, BS 5467, IEC 60502-1, BS 7889 all

supplymentary.The rate shall include complete

Supply, Installation, testing and commissioning rates

including cost of all tools and accessories required to

Complete the job in full respect.

3.1.1 3.5C x 150 SQMM Armoured AL Cable 200.00 RM

3.1.2 3.5C x 120 SQMM Armoured AL Cable 180.00 RM

3.2 Supplying and drawing following sizes of FRLS PVC

insulated copper conductor, single core cable in the

existing surface/recessed steel/PVC conduit as reqd.

3.2.1 1C x 70 SQMM PVC INS. PVC SH. FRLS CU. FLEX.

CABLE

40.00 RM


CABLE

290.00 RM


CABLE

100.00 RM


CABLE

100.00 RM


CABLE

80.00 RM


CABLE

150.00 RM

3.2.7 3C x 1.5 SQMM PVC INS. PVC SH. FRLS CU. FLEX.

CABLE

100.00 RM

3.2.8 3C x 2.5 SQMM PVC INS. PVC SH. FRLS CU. FLEX.

CABLE

100.00 RM

3.2.9 3C x 4 SQMM PVC INS. PVC SH. FRLS CU. FLEX. CABLE 150.00 RM


in Rupees

Amount

3.2.10 3C x 6 SQMM PVC INS. PVC SH. FRLS CU. FLEX. CABLE 100.00 RM

3.3 Wiring for circuit/ submain wiring alongwith earth

wire with the following sizes of FRLS PVC insulated

copper conductor, single core cable in surface/

recessed steel conduit as required

3.3.1 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 204.00 RM







3.4 Laying of on number PVC insulated and PVC

sheathed/XLPE power cable of 1.1 kv grade of size

following sizes direct in ground including excavation,

snd cushioning, protective covering and refilling the

trench etc as required.

3.4.1 less than 35sqmm 120.00 Mtr.

3.4.2 exceeding 35 sq.mm.but not exceeding 95 sqmm 250.00 Mtr.

3.4.3 exeeding 95 sq.mm.but not exceeding 185 sqmm 120.00 Mtr.

3.5 Laying of on number additional PVC insulated and

PVC sheathed/XLPE power cable of 1.1 kv grade of

size following sizes direct in ground in the same

trench in one tier horizontal formation including

excavation, snd cushioning, protective covering and

refilling the trench etc as required.

3.5.1 less than 35sqmm 120.00 Mtr.

3.5.2 exceeding 35 sq.mm.but not exceeding 95 sqmm 250.00 Mtr.

3.5.3 exeeding 95 sq.mm.but not exceeding 185 sqmm 120.00 Mtr.


in Rupees

Amount

3.6 Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

following size in the existing RCC/ HUME/ METAL

pipe as required.

3.6.1 Upto 35 sq. mm 30.00 Mtr.

3.6.2 Above 35 sq. mm and upto 95 sq. mm 40.00 Mtr.


3.7 Laying of one number PVC insulated and PVC

sheathed / XLPE power cable of 1.1 KV grade of

following size in the existing masonry open duct as

required.3.7.1 Upto 35 sq. mm 30.00 Mtr.



3.8 Laying and fixing of one number PVC insulated and

PVC sheathed / XLPE power cable of 1.1 KV grade of

following size on wall surface as required.

3.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) 10.00 Mtr.

3.8.2 Above 35 sq. mm and upto 95 sq. mm (clamped with

25x3mm MS flat clamp)

20.00 Mtr.

3.8.3 Above 95 sq. mm and upto 185 sq. mm (clamped

with 25/40x3mm MS flat clamp)

10.00 Mtr.

3.9 S/F, copper cable lug suitable for following size of

conductor.

3.9.1 2.5 Sqmm 24.00 Nos.

3.9.2 4 Sqmm 24.00 Nos.

3.9.3 6 Sqmm 24.00 Nos.

3.9.4 10 Sqmm 24.00 Nos.

3.9.5 16 Sqmm 24.00 Nos.

3.9.6 25 Sqmm 24.00 Nos.


in Rupees

Amount

3.9.7 70 Sqmm 12.00 Nos.

3.10 Supplying and making end termination with brass

compression gland with aluminium lugs for following

size of PVC insulated & PVC sheathed/XLPE

aluminium cable of 1.1kV grade as reqd.

3.10.1 3.5C x 150 SQMM A2XFY 4.00 Each

3.10.2 3.5C x 120 SQMM A2XFY 6.00 Each

3.10.3 3.5C x 95 SQMM A2XFY 10.00 Each

3.10.4 3.5C x 70 SQMM A2XFY 2.00 Each

3.10.5 3.5C x 50 SQMM A2XFY 2.00 Each

3.10.6 3.5C x 35 SQMM A2XFY 8.00 Each

3.10.7 3.5C x 25 SQMM A2XFY 4.00 Each

3.10.8 2C x 6 SQMM A2XFY 14.00 Each

4 CABLES TRAYS & RACEWAYS

Supply and fixing of factory fabricated GI perforated

type hot dip galvanised cable trays, with radial bends,

suspenders and supports as per specification and of

the following sizes.

4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness 45.00 RM




4.2 Supply and fixing of factory fabricated ladder type

hot dip galvanised cable trays, with necessary bends,

cross arms and supports as per specification and of

the following sizes.




in Rupees

Amount

RACEWAYS

4.3 Supply, Installation testing and commissioning of

metallic adaptable raceway system ,

compartmentalised of following mentioned sizes

suitable for passing through walls and floors as per

the layout ,suitable for FRLS wires confirming to

IS:694 and extra low voltage cables for data

/AV/telephone. The raceway shall have Z- section,

hole with thread for cover screw, coupler plate,

cover, junction box, fly cover , inspection box flushed

to the finished floor at suitable distances etc as

required. The screw for cover fixing shall be counter

sunk type.The cover shall have a thickness of

2mm.The cost shall also include the cost of bends

couplers and any other suporting accessories.

4.3.1 75 mm x 40 mm x 1.6 mm 24.00 RM

4.3.2 100 mm x 40 mm x 1.6 mm 20.00 RM

4.3.3 150 mm x 40 mm x 1.6 mm 40.00 RM

4.3.4 200 mm x 40 mm x 1.6 mm 260.00 RM

4.3.5 300 mm x 40 mm x 2 mm 121.00 RM

4.4 Supplying, installation DLP mini- trunking 32mm x

20mm and accessories white-system with

independent cover- without central partion etc. as

reqd.

100.00 RM

4.5 Supply and fixing of following items for plastic

trunking accessories suitable for size 32 mm x 20 mm

4.5.1 End cap 10.00 Nos.

4.5.2 Internal angle/ External angle 20.00 Nos.

4.5.3 Changeable flat angle 20.00 Nos.

4.5.4 Flat Junction 10.00 Nos.

4.6 Providing and fixing DLP plastic trunking of size 105

mm x 50 mm without cover on surface as reqd.

150.00 RM


in Rupees

Amount

4.7 Providing and fixing 85 mm width flexible cover of

DLP plastic trunking. (size 105 mm x 50 mm.)

150.00 RM

4.8 Supply and fixing of following items for plastic

trunking accessories suitable for size 105 mm x 50

mm.4.8.1 End cap 8.00 Nos.

4.8.2 Internal angle. 12.00 Nos.

4.8.3 External angle 10.00 Nos.

4.8.4 Flat Junction 4.00 Nos.

4.8.5 Changeable flat angle 8.00 Nos.

4.8.6 Separation partitions 130.00 RM

4.8.7 cover joint 20.00 Nos.

4.8.8 Base joint 40.00 Nos.

5 DISTRIBUTION BOARDS

5 Supplying and fixing following way, single pole and

neutral, sheet steel, MCB distribution board, 240

volts, on surface/ recess, complete with tinned

copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing

etc. as required. (But without MCB/RCCB/Isolator)

5.1.1 2 + 8 Way Double door 4.00 Each

5.1.2 2 + 12 Way Double door 4.00 Each

5.2 Supplying and fixing following way, horizontal type

three pole and neutral, sheet steel, MCB distribution

board, 415 V, on surface/ recess, complete with

tinned copper bus bar, neutral bus bar, earth bar, din

bar, interconnections, powder painted including

earthing etc. as required.(But without MCB/ RCCB/

Isolator)

5.2.1 8 way ( 4 + 24 ), Double door 4.00 Each


in Rupees

Amount

5.3 Supplying and fixing following way prewired vertical

type TP&N MCB distribution board of steel sheet for

415 volts on surface/ recess complete with loose wire

box of sheet steel, dust protected, duly powder

painted, inclusive of 200 amps tinned copper bus bar,

common neutral link, earth bar, din bar for mounting

MCB's, terminal connectors for all incoming and

outgoing circuits, duly prewired with adequate size of

FR PVC insulated copper conductor upto the terminal

connector/ neutral link, earthing etc as required (But

without MCB/ RCCB/ Isolator).

5.3.1 8 way Double door 1.00 Each

5.3.2 12 way Double door 2.00 Each

5.4 S & F following rating and pole, 240 volts 'C' curve 10

kA, lexic MCB of following pole in the existing MCB

DB complete with connection, testing &

commissioning etc as reqd. 5.4.1 Single Pole ( 5 Amp to 32 Amp ) 213.00 Each

5.4.2 Double Pole ( 5 Amp to 32 Amp ) 2.00 Each

5.4.3 Tripple Pole ( 5 Amp to 32 Amp ) 7.00 Each

5.4.4 Tripple pole & Neutral ( 5 Amp to 32 Amp ) 1.00 Each

5.4.5 Single Pole ( 40 Amp to 63 Amp ) 5.00 Each

5.4.6 Double Pole ( 40 Amp to 63 Amp ) 8.00 Each

5.4.7 Tripple pole ( 40 Amp to 63 Amp ) 7.00 Each

5.4.8 Tripple pole & Neutral ( 40 Amp to 63 Amp ) 5.00 Each

5.5 Supplying and fixing following rating, double pole,

(single phase and neutral), 240 volts, residual current

circuit breaker (RCCB), having a sensitivity current

upto 300 milliamperes in the existing MCB DB

complete with connections, testing and

commissioning etc. as required.

5.5.1 63 amps 12.00 Each


in Rupees

Amount

5.6 S & F metal box of following sizes ( nominal ) on

surface or recess with suitable size of MS sheet cover

in the front I/c painting etc as reqd.

5.6.1 375 mm x 175 mm x150 mm deep 2.00 Each






5.7 Providing and fixing following rating and breaking

capacity four pole 415V 50Hz MCCB in existing

cubicle panel board including drilling holes in cubicle

panel, making connections, etc as required.

5.7.1 125 Amp, 25KA 2.00 Each

55.8 S&F connecting and commissioning indipendent

mounting of 125/200 Amp MCCB enclosure make

legrand or its equivalent approved make in

surface/recess I/c cutting the wall and making good

the same in case of recessed as reqd.

2.00 Each

6 POINT WIRING AND SWITCH SOCKETS

6.1 Wiring for light point/ fan point/ exhaust fan point/

call bell point with 1.5 Sq.mm FRLS PVC insulated

copper conductor single core cable in surface /

recessed steel conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5

Sq.mm. FR PVC insulated copper conductor single

core cable etc as required.

6.1.1 Group C 575.00 Nos.


in Rupees

Amount

6.2 Wiring for twin controlled Light point with1.5 sq.mm

FRLS PVC insulated Copper Conductor single core

cable in surface / recessed steel conduit, 2 way

modular switch, modular plate, suitable GI Box and

earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc as reqquired.

6.2.1 Group C 5.00 Nos.

6.3 Supplying and fixing suitable size GI box with

modular plate and cover in front on surface or in

recess, including providing and fixing 3 pin 5/6 amps

modular socket outlet and 5/6 amps modular switch,

connection etc as required. (for light plugs to be used

in non reseidential buildings).

216.00 Nos.

6.4 Supplying and fixing suitable size GI box with

modular plate and cover in front on surface or in

recess, including providing and fixing 6 pin 5/6 &

15/16 amps modular socket outlet and 15/16 amps

modular switch, connection etc as required.

178.00 Nos.

6.5 Supplying and fixing 20 amps, 240 volts, SPN

industrial type, socket outlet, with 2 pole and earth

metal enclosed plug top along with 20 amps ' C '

series SP, MCB, in the sheet steel enclosure, on

surface or in recess, with chained metal cover for the

socket outlet and complete with connections, testing

and commissioning etc as required.

44.00 Nos.

6.5 Supplying and fixing of following sizes of steel conduit

along with accessories in surface/recess including

painting in case of surface conduit, or cutting the wall

and making good the same in case of recessed

conduit as reqd.

6.6.1 20 mm dia 1000.00 RM

6.6.2 25 mm dia 1500.00 RM

6.6.3 32 mm dia 300.00 RM

6.6.4 40 mm dia. 200.00 RM


in Rupees

Amount

6.7 S & L following size of GI pipe in ground after digging

the trench & refilling the same ramming the loose soil

and making good the same as reqd.

6.7.1 40 mm dia. 40.00 RM

7 LIGHT FIXTURES, CEILING FANS/EXHAUST/WALL

FANS 7.1 Supply, Installation, Testing and Commissioning of

following LED Lighting fixtureswith as per the

technical specifications and all accessories including

electronic drivers, dffiusers and all tools and

accessories required to complete the job in full

respect

7.1.1 18w LED surface mounted Light 107.00 Nos.

7.1.2 18w LED recess mounted Light 107.00 Nos.

7.1.3 12w LED surface mounted Light 200.00 Nos.

7.1.4 12w LED recessed Light 20.00 Nos.

7.1.5 5W LED Mirror Light 20.00 Nos.

7.1.6 20W LED Batten Light 50.00 Nos.

7.1.7 40W 4 feet lon surface mounting/ceiling suspeneded

LED Light

50.00 Nos.

7.1.8 10w Bulk Head Fittings 12.00 Nos.

7.1.9 1x9/10WLED Wall mounted Light 30.00 Nos.

7.1.10 36W 2'X2' Sqaure Recessed Light 250.00 Nos.

7.2 Supply, Installation, Testing and Commissioning of

following fans as per the technical specifications and

all accessories including hanging pendent, fully

painted with inbuilt motor and capacitor. and all tools

and accessories required to complete the job in full

respect

7.2.1 1200 mm Sweep ceiling fan 75.00 Nos.

7.2.2 400 mm Sweep Wall Fan 15.00 Nos.


in Rupees

Amount

7.2.3 300 mm Exhaust fan 20.00 Nos

7.3 Supply and fixing ceiling fan box 150 mm dia x 75 mm

deep fabricated from 16 SWG MS sheet with cover

for the top and 3 mm hylam sheet with brass screw,

cover for the bottom having suitable holes for fan

hook & conduit entry including 12 mm dia MS rod

hook duly bend in shape and projecting 150mm on

either side of box , complete as reqd.

75.00 Nos

8 EARTHING INSTALLATIONS

8.1 Earthing with GI earth electrode 50mm dia x 3 mtr

length including earth enhancing compound (Jam Fill

quality product) and PIT cover for earthing pit etc as

reqd. (193GI JMV)

4.00 Nos.

8.2 Earthing with Copper bonded earth electrode 50mm

dia x 3 mtr length including earth enhancing

compound (Jam Fill quality product) and PIT cover for

earthing pit etc as reqd. (503 CBE JMV).

4.00 Nos.

Earth conductors

8.3 Providing and fixing 25 mm X 5 mm copper strip in 40

mm dia G.I. pipe from earth electrode including

connection with brass nut, bolt, spring, washer

excavation and re-filling etc. as required.

150.00 RM

8.4 Supply, Installation, Testing and Commissioning of

following Earth strips/wire on surface or in recess ats

as required.

8.4.1 25 x 5 sqmm GI strip 200.00 RM

8.4.2 25 x 5 sqmm CU strip 150.00 RM

8.4.3 6 SWG GI Wire 200.00 RM

9 LIGHTNING PROTECTION SYSTEM


in Rupees

Amount

9.1 Supply, Design & Testing of Prevectron type 3rd

Generation Controlled Early Streamer Emission

(CESE) lightning conductor equipped with a tinned

copper central pick up rod. Full electrical continuity

between the tip and the earth point shall be ensured.

Fully autonomous (no battery, no external power

supply required) which shall collect ambient energy

through a lower series of electrodes. Timing of the

streamer emission controlled with an electronic

device that detects the lightning and triggers a

streamer (3.5 KV and 20 A). Manufactured as per NFC

17-102.

A tester/ testing process corresponding specifically to

the airterminal shall be available for the maintenance

and ensure the healthiness of the unit.

Protection Radius = 26 meters

1.00 Set

9.2 Elevation pole made of GI with a dia of 35mm to

50mm with a thread at the top to fix the unit. Base

plate, mounting bracket, clamps and all required

fixing accessories . (The base of the down conductor

should be protected from accidental knocks and

other damage by means of a 2 meters stainless-steel

or PVC protection sheath fixed to the structure.)

(5meter ht. considered)

1.00 Set

9.3 Supply of Wireless Remote Control unit required only

for testing the Prevectron air terminal.

1.00 Set

9.4 Down Conductor :Supply of Test Clamp to connect

the down conductor to the earth termination and

disconnect the down conductor from the earth

termination for regular checks of the earth

termination resistance value.

2.00 Set

9.5 Performance Recording Equipment : Supply of

Lightning Flash Counter. Electronically controlled,

register every strike between 1000 A to 100 KA for a

8/20 microsecond peak current. Tested in High

Voltage Laboratory (CPRI).

1.00 Set

9.6 Supply, Installation testing and commissioning of

conventional type franklin rod with itss PCC base

support to be mounted on the highest point of the

building structure along with downleads.

1.00 Set


in Rupees

Amount

10 TEL. & DATA SYSTEM

Defination : This includes the provisions for

Telephone, Intercom, Data. This includes following

items

10.1 Supplying and drawing following pair 0.5 Sq.mm FR

PVC insulated copper conductor, unarmoured

telephone cable in the existing surface/recessed

steel/PVC conduit as reqd.

10.1.1 2 Pair 500.00 RM

10.2 S&L, connecting and commissioning 50 pairs jelly

filled un-armoured telephone cable PVC insulated

and PVC sheathed annealed tinned copper

conductor.

10.2.1 Direct in ground I/c excavation, sand cushioning,

protective covering and refilling the trench etc. as

reqd.

80.00 RM

10.2.2 On surface with MS clamp 10.00 RM

10.2.3 In pipe 5.00 RM

10.2.4 In open duct 5.00 RM

10.3 S & F following rating moduler RJ-11 telephone jack

(1M) complete with moduler base & cover plate etc

as reqd.

20.00 Each

10.4 Fixing, Internet Box of size 75mm x 75mm x 40 mm

including brass screw on surface / recessed as reqd.

50.00 Each

10.5 Drawing of computer network cable in existing pipe /

casing and capping as reqd including numbering the

wires at both the ends.

1400.00 RM

10.6 Fixing of telephone DP/network rack ( HUB ) on wall

floor with suitable brick foundation on bolts and nut

etc. as reqd.

3.00 Nos.

11 FIRE ALARM SYSTEM

Note: Colour coding for conduits to be done for

different systems. The whole length of conduits to

be painted.


in Rupees

Amount

All AC's and fire Escape VTPN DB shall be integrated

with main fire panel so that in case of fire signal, all

the AC's will be switched off and fire escape VTPN DB

will work.

2 Layer For above false ceiling and below false ceiling

11.1 Supply, installation, connecting, testing and

commissioning of addressable photoelectric type

Smoke Detectors with mounting base, blinking LED

etc. complete as required.

8.00 Nos


commissioning of addressable Type Multi Sensor

Smoke Detectors with mounting base etc. complete

as required.

99.00 Nos


commissioning of addressable rate of rise cum fixed

temperature Heat Detectors with mounting base,

blinking LED etc. complete as required.

2.00 Nos


commissioning of Addressable Hooters cum strobe

min. 95 db output , the cost includes of control

module if required

8.00 Nos


commissioning of Addressable Manual Call Box in

ABS plastic as required complete.

8.00 Nos


commissioning of addressable fault Isolator

11.00 Nos


commissioning of addressable control module for

A.C. & Access Control System

4.00 Nos


commissioning of addressable monitor module for

integration of builder panel to main fire panel

4.00 Nos


commissioning of UL Listed Addressable Beam

Detector with Receiver, transmitter including all

accessories as required.

2.00 Set


in Rupees

Amount


commissioning of Control Relay Module

4.00 Nos


commissioning of Response indicator.

2.00 Nos

11.12 Supply Installation, Testing & Commissioning of UL

listed, 9th edition 32 bit Fire alarm control panel

having microprocessor based 2 loop cards

expandable upto 4 loops with 252 intelligent points /

loop cards in any flexible combination (detectors/

devices ) . The panel have 6 inch long LCD touch

screen and LED's for displaying system status. In

addition to the digital screen, the user can view a

graphics map which can show a simple building floor

plan. The panel shall provide the user with 40

programmable macro or function buttons, which can

be programmed for a variety of usages like

controlling AHU's, Pressurisation fans, fire pumps,

monitoring of flow switches in fire pipe line etc. The

panel shall have 240 V AC power supply, automatic

battery charger, 24 V SMF batteries sufficient for 24

hour in standby and 15 minutes in alarm complet as

per specification. The panel shall be able to give

relay outputs to the PA system if applicable.

1.00 Nos

11.13 Providing and fixing in position the following G.I.

flexible conduits including all accessories

11.13.1 1.6mmwall thickness 20mm dia 50.00 RM

11.13.2 1.6mm wall thickness 25 mm dia 60.00 RM

11.14 Providing and fixing in position 1.2mm thick M.S.

outlet boxes for housing smoke detectors/heat

detectors including providing 3 mm thick hylam sheet

cover as required11.14.1 75mm x 75mm x 75mm 4.00 Nos

11.15 Supplying and drawing following sizes of FRLS PVC

insulated copper conductor, single core cable in the

existing surface/recessed steel/PVC conduit as reqd.

11.15.1 2 core x 1.5 sq. mm 1500.00 RM


in Rupees

Amount

12 PUBLIC ADDRESS SYSTEM

12.1 Supply,installation,testing and commissioning of

following Philips (BOSCH) make Music

Accessories/Equipments.12.1.1 Ceiling Speaker Unit 6 Watts LHM 0606/10 45.00 Nos.

12.1.2 Wall mounted Speaker Unit 6 Watts 19.00 Nos.

12.1.3 Power Amplifier, 480 Watts with output transformer

etc. complete.

1.00 Nos.

12.1.4 Power Amplifier, 120 Watts with output transformer

etc. complete.

1.00 Nos.

12.1.5 System pre-amplifier with suitable size of PA

controller, Router, console, call station and call

station keypad for above system

1.00 Nos.

12.1.6 Single DVD player Philips/Samsung. 1.00 Nos.

12.1.7 6 Zone call station ( Bosch Make LBB 1946/10) 1.00 Nos.

12.1.8 Control Unit (with volume and on/off switch) Philips

(Smooth stepless control, but the control shall be

through dimmer switch, the make of which will be

same as the make of light control switches)

1.00 Nos.

12.1.9 Philips Microphone unit Cat no. LBD 8292 1.00 Nos.

12.1.10 Equipment Rack complete with monitor unit,

speaker, power supply control etc. President make

Suitable for above system

1.00 Nos.

12.1.11 Main Termination Box 1.00 Nos.

12.1.12 Supply and drawing of 1.5 sq. mm Twin Core

shielded Speaker Cable in existing conduit.(Fusion

/Excel/BonTon)

700.00 RM

Total Rs.

Documents

INDIAN INSTITUTE OF TECHNOLOGY KANPUR Tender Notice No. … · 3.1.1 3.5C x 150 SQMM Armoured AL Cable 200.00 RM ... CABLE 100.00 RM 3.2.4 3C x 16 SQMM PVC INS. PVC SH. FRLS CU. FLEX