800 Broadway – Haverhill, MA 01832 USA – TEL 978-556-0077 – FAX 978-556-0171 – www.ims-software.com IMSpost™ CATIA V5 and DELMIA V6 Integration Updated October 7, 2013 Integration within Dassault Systemés CATIA V5 and DELMIA V6 is achieved through the inclusion of IMS Post Processor run time software embedded within the Dassault Systemés product install. On a standard 64bit system install this is in the following directories depending on whether it is the V5 or V6 platform. C:\..........\B22\win_b64\code\bin\MfgPPIG2Imp.dll C:\..........\B214\win_b64\code\bin\MfgPPIG2Imp.dll Current standard installs from Dassault Systemés have not updated the level of this file to the current level recommended by IMS Software. Today IMS Post Processor products are running at Release level 8.1 whilst the integrated version is at 7.4. IMS recommends that you update your system to run on the latest level of IMS Post Processor software. This can be obtained from the IMS Software website. You need to login using your IMS Software account ID and Password and then select the 'Downloads' tab on the web page. If you do not have a login ID then please request one from the web page. Installation process To install these new codes you first need to 'unzip' the files locally. Then copy them into your system CATIA / DELMIA install directory as discussed previously. The recommendation is to rename the original files to a 'safe' name so you keep the original level of software should it be required again at some point in the future.
800 Broadway Haverhill, MA 01832 USA TEL 978-556-0077 FAX
978-556-0171 www.ims-software.com
IMSpost CATIA V5 and DELMIA V6 Integration Updated October 7,
2013
Integration within Dassault Systems CATIA V5 and DELMIA V6 is
achieved through the inclusion of IMS Post Processor run time
software embedded within the Dassault Systems product install. On a
standard 64bit system install this is in the following directories
depending on whether it is the V5 or V6 platform.
Current standard installs from Dassault Systems have not updated
the level of this file to the current level recommended by IMS
Software. Today IMS Post Processor products are running at Release
level 8.1 whilst the integrated version is at 7.4.
IMS recommends that you update your system to run on the latest
level of IMS Post Processor software. This can be obtained from the
IMS Software website. You need to login using your IMS Software
account ID and Password and then select the 'Downloads' tab on the
web page. If you do not have a login ID then please request one
from the web page.
Installation process
To install these new codes you first need to 'unzip' the files
locally. Then copy them into your system CATIA / DELMIA install
directory as discussed previously. The recommendation is to rename
the original files to a 'safe' name so you keep the original level
of software should it be required again at some point in the
future.
800 Broadway Haverhill, MA 01832 USA TEL 978-556-0077 FAX
978-556-0171 www.ims-software.com
1) Locate the bin folder in your install of CATIA. (Paths shown
as an example of where the files are located on a default install
path.) x32 C:\Program Files (x86)\Dassault
Systemes\B20\intel_a\code\bin
3) Locate the file MfgPPIG2Imp.dll and rename it to append
something to the extension so you can save off your current dll in
the case that you need it at some future date.
4) Copy in the dll from the web site which corresponds to your
CATIA version (x32 or x64)
5) Rename the new dll file so that it simply has an extension of
.dll
800 Broadway Haverhill, MA 01832 USA TEL 978-556-0077 FAX
978-556-0171 www.ims-software.com
Confirming correct IMS Software level
To confirm that you have the correct level of IMS Software
installed on your CATIA / DELMIA installation you need to run a
diagnostic check. This is done from the CATIA / DELMIA NC Code
Interactive output panel opened from within an active CATProcess
document.
Select the License Diagnostics button and fill out the form to
select a location to write your diagnostic file.
The report will then be built and displayed. The first section
displays your current embedded IMS Software level.
