HP2-Z26

HP HP2-Z26

Fast Track - Implementing HP Network TechnologiesVersion: 6.0

QUESTION NO: 1 What are the default logging properties for an HP Comware switch? (Select two.) A. Displays debugging output to the console B. Displays log messages to the console C. Uses the Information Center to control logging functions D. Uses the Event Log to save log messages E. Supports five logging levels

Answer: B,C

Explanation:

QUESTION NO: 2 Which statements are true about the Network Time Protocol (NTP)? (Select two.) A. It can deliver time-stamped messages via a multicast delivery system. B. It delivers time-stamped messages using TCP to port 123. C. The most precise time source is a stratum level 16 clock. D. Timestamps can be digitally signed with certificates. E. Timestamps can be digitally signed for verification.

Answer: A,E

Explanation:

QUESTION NO: 3 Before upgrading networking equipment like switches, a network administrator should first performsome important preparation tasks. What should the network administrator include in the creation ofan upgrade policy? (Select two.) A. Read the release notes of the old operating system. B. Update network management software before deploying upgrades to network switches C. Verify remote access connectivity to the device to be upgraded. D. Make a copy of the old operating system. E. Test the upgrade in a lab network or a less important part of the network first.

Answer: C,E

Explanation: Test the upgrade in a lab network set up for testing patches, upgrades, etc. If the

HP HP2-Z26 Exam

"Pass Any Exam. Any Time." - www.actualtests.com 2

device is connected in a remote location, test the remote access connectivity before upgrading.

QUESTION NO: 4 Based on the default precedence used to rank routing protocols in HP Comware switches, if adefault route (0.0.0.0/0) is learned from multiple routing protocols, which source would theComware operating system prefer? A. Static B. RIP C. External BGP D. Internal OSPF

Answer: A

Explanation:

QUESTION NO: 5 A company has two buildings that are 15 meters apart. The company needs to connect thebuildings' networks. The CFO does not want the cost of installing fiber between the two buildingsand thus is exploring wireless options. If the company selects an 802 11n wireless solution, which wireless mode should they use? A. Bridge mode B. Infrastructure mode C. In-cell relay mode D. Point-to-Point mode

Answer: C

Explanation: http://compnetworking.about.com/cs/wireless/f/infrawireless.htm

QUESTION NO: 6 Refer to the link aggregation between two HP switches.

HP HP2-Z26 Exam


--

The link aggregation is failing between the HP Provision and HP Comware switches. Whichsolution solves this problem? A. The Provision switch must be reconfigured for static LACP. B. TheProvision switch must be reconfigured for dynamic link aggregation. C. TheComware switch must be reconfigured for dynamic LACP active mode. D. TheComware switch must be reconfigured for static LACP.

Answer: A

Explanation:

QUESTION NO: 7 A network administrator is building two IRF domains:

One domain for the two distribution layer switches One domain for the access layer switches

Each access layer switch should have a connection to each distribution layer switch. In thisdesign, how many access switches can the administrator have in the access layer IRF domainbefore spanning tree is required to remove loops between the two IRF domains? A. 2 B. 4 C. 6 D. 8

HP HP2-Z26 Exam


E. 12

Answer: A

Explanation:

QUESTION NO: 8 Refer to the network exhibit.

A network administrator needs to configure DHCP on an HP Comware switch. The networkadministrator configures the following information:

After setting up DHCP relay, the network administrator has the DHCP client try to acquireaddressing information, but the process fails. What should the network administrator do to solvethis problem? A. Configure DHCP relay on SwitchB. B. Execute the routing command on SwitchA. C. Execute the dhcp enable command on SwitchA. D. Enable DHCP Snooping on SwitchA.

Answer: C

Explanation:


HP HP2-Z26 Exam


A network administrator has created a layer 2 network based on the design shown in the exhibit.Switch-A and Switch-B are distribution layer switches. Switch-C is an access layer switch. What isthe best spanning tree solution for this environment? A. STP B. RSTP C. PVST+ D. MSTP

Answer: D

Explanation:


HP HP2-Z26 Exam


HP HP2-Z26 Exam


A network administrator has a server with a single link to the network The company is concernedabout redundancy and wants to implement a solution like that shown in the right-hand side of thediagram. Which solution meets the company's needs? A. HP Comware switches using distributed trunking or IRF B. HP Comware switches using distributed trunking only C. HP Comware switches using meshed IRF or meshed stacking D. HP Comware switches using IRF only E. HP Comware or HP Provision switches using IRF

Answer: D

Explanation:

QUESTION NO: 11 Refer to the HP Provision and HP Comware configurations.

HP HP2-Z26 Exam


An aggregated link has been defined between the Provision A1 and A2 switches, as well asbetween the Comware g1/0/1 and g1/0/2 switches. 1 and 2 is not being passed between theswitches. However, during the network administrator's tests, traffic for VLAN. What is the cause ofthis problem? A. The PVID on the Comware switch does not match the Provision switch B. The VLAN properties need to be defined on A1 and A2 of the Provision switch. C. The aggregated link protocol does not match on the two switches D. The VLAN properties need to be defined on BAGG1 of the Comware switch

Answer: C

Explanation:

HP HP2-Z26 Exam


QUESTION NO: 12 A network administrator has installed IMC and the appropriate licenses. The network administratoris attempting to import the HP Comware and HP Provision switches into IMC but is experiencingproblems importing the Comware switches. The network administrator verifies the SNMPv2cconfiguration on both sets of switches and the SNMP configuration in IMC. The SNMP parametersare correct. What is the cause of the import problem? A. Comware switches are not fully supported by IMC. B. Comware switches implement SNMPv3 by default. C. Comware switches require SSH to be configured for remote CLI access. D. Comware switches do not have telnet fully configured.

Answer: B

Explanation:

QUESTION NO: 13 HOTSPOT Select the items that correspond to RIPv1 or RIPv2.

HP HP2-Z26 Exam


Answer:

HP HP2-Z26 Exam


Explanation:

QUESTION NO: 14 Which HP information management product manages large data volumes, is known for fast queryperformance, and is available on HP DL380 rack-mount servers? A. HP Moonshot B. HP StoreAll C. HP AppSystem for SAP HANA D. HP Vertica Analytics System

Answer: D

Explanation:


HP HP2-Z26 Exam


The network shown in the exhibit is comprised of four MSTP regions that are interconnectedBased on this topology, which statement is true? A. PVST should be used instead of MSTP B. A routing solution must be used between MSTP regions when more than one region exists C. An optimized topology can be created using MSTP between the regions D. The switches are running the equivalent of RSTP between the regions

Answer: D

Explanation:


HP HP2-Z26 Exam


When should the topology shown in the exhibit be implemented in a network? A. When roaming is not desired B. When autonomous mode is needed on the APs C. When a layer 2 switched network is required D. When centralized management of APs is required

Answer: D

Explanation:

QUESTION NO: 17 Which configuration tool do HP Provision switches support that HP Comware switches do notsupport? A. Menu system B. SNMP C. Web-based

HP HP2-Z26 Exam


D. Auto configuration tool

Answer: A

Explanation:

QUESTION NO: 18 Which statements are correct about HP StoreOnce Backup? (Select two.) A. It provides long term data retention using tape backup libraries with LT0-6 technology. B. It is a modular, branch-in-a-box solution that reduces the cost of remote installations C. It transfers only unique data across the network and stores it on the remote backup devices. D. It reduces bandwidth and storage media use with deduplication technology. E. It provides high-speed data backup using a 3U rack enclosure with multiple tape arrays.

Answer: C,D

Explanation:

QUESTION NO: 19 Which HP Comware command saves the startup configuration file to a TFTP server? A. Rescore B. Startup C. Backup D. Copy

Answer: CReference:http://www.h3c.com/portal/Technical_Support___Documents/Technical_Documents/Switches/H3C_5820X_Series_Switches/Maintenance/Maintenance/H3C_Login_Password_Recovery_Manual(V1.01)/( see user level switching password, see user view commands)

QUESTION NO: 20 What is the default state of spanning tree on HP Comware switches?

HP HP2-Z26 Exam


A. MSTP is enabled. B. RSTP is enabled. C. STP is disabled. D. PVST is enabled.

Answer: A

Explanation:

QUESTION NO: 21 A network administrator is implementing a network with HP Comware and HP Provision switches.When the network administrator boots the switches for the first time, what are the factory defaultsettings of all of the switches in the network? (Select two.) A. All interfaces are enabled. B. Routing is enabled. C. SSH is enabled. D. DHCP client is defined for all VLANs. E. No passwords are defined.

Answer: A,E

Explanation:

QUESTION NO: 22 A network administrator has an HP Comware switch that is configured with OSPF. The networkadministrator views the routing table and sees that a default route was learned from an OSPFneighbor (10.1.1.1). However, the network administrator wants to override this action and use adifferent neighbor (10.1.1.2) for the default route. The network administrator configures this command: [Commware] ip route-static 0.0.0.0 0 10.1.1.2 After configuring the command, the network administrator examines the routing table and noticesthat the original neighbor's default route is still in the routing table, but the static route is missing. What is the cause of this problem?

HP HP2-Z26 Exam


A. OSPF routes have a lower precedence value. B. Only one routing protocol can be operational on a Comware device. C. The ip default-gate way command must be used when creating a default route. D. The static route has a syntax mistake.

Answer: A

Explanation:


HP HP2-Z26 Exam


A network administrator needs to configure link aggregation using static LACP on Switch-A. Whichis an HP Comware switch. Which configuration accomplishes this goal?

A. Option A B. Option B C. Option C D. Option D

Answer: C

Explanation:

QUESTION NO: 24

HP HP2-Z26 Exam


What are HP Cloud Maps? A. HP templates that make applications such as Oracle and Microsoft SharePoint ready for push-button deployment. B. HP business best practices that help organizations transition from traditional computing to cloudcomputing. C. HP information management technology that helps users analyze location-based data oftenfound in large data sets. D. HP software that automates routine IT tasks within a cloud environment.

Answer: AReference:http://h20000.www2.hp.com/bc/docs/support/SupportManual/c03482833/c03482833.pdf (page 2,see introduction, second para)

QUESTION NO: 25 Refer to the HP Comware configuration.

The network administrator set up VLAN 2 as a management VLAN. This VLAN should not beincluded in the OSPF routing process. Now only directly connected network administrators inVLAN2 can manage the switch.

HP HP2-Z26 Exam


How should the network administrator solve this problem? A. Define the management-vlan 2 command. B. Define the VLAN 2 interface as a silent interface. C. Change the network command in OSPF. D. Define the ip authorized-managers 10.1.0.0/24 command.

Answer: D

Explanation:


The network is running spanning tree. Examine this configuration of Switch-C:

HP HP2-Z26 Exam


Port 1 on Switch-C fails. Based on this topology, which statement is true? A. If PVST+ was running, a loop-free topology would be created. B. If Port Monitor was running, a loop-free topology would be created. C. If MSTP was running, a loop-free topology would be created. D. If RSTP was running, a loop-free topology would be created.

Answer: C

Explanation:

QUESTION NO: 27 Which Software-Defined Network (SDN) layer includes HP Provision and HP Comware switches? A. Infrastructure B. Application C. Operational D. Control

Answer: A

Explanation:

QUESTION NO: 28 A network administrator attempts to access the console port of an HP Comware switch. Thenetwork administrator is immediately prompted for a username and password, but cannotremember the correct account information. The network administrator then reboots the switch andaccesses the ExtendedBootROM menu, where this information displays:

HP HP2-Z26 Exam


Which option can the network administrator choose to get access to User and System Views fromthe switch's console port? A. Option 4 B. Option 5 C. Option 6 D. Option 8

Answer: D

Explanation:

QUESTION NO: 29 Which HP Provision switch command lists the operating system that is currently loaded? A. Show boot-set B. A show flash C. Show boot-files D. Show version

Answer: D

Explanation:

QUESTION NO: 30

HP HP2-Z26 Exam


Which HP redundancy features are supported by both HP Provision and HP Comware switches?(Select two.) A. Dynamic LACP meshed stacking B. Distributed trunking C. Static link aggregation D. Static LACP

Answer: A,D

Explanation:

QUESTION NO: 31 A network administrator is examining the routing table on an HP Comware switch. The networkadministrator sees two routes. 10.1.1 0/24, with the same neighbor's address (10.1.1.1). Whatwould create this result? A. There is an aggregated link with two connections between the two routers. B. The bandwidth of the two routes is the same. C. The administrative distance of the two routes is the same. D. The cost of the two routes is the same.

Answer: A

Explanation:

QUESTION NO: 32 A network administrator is expanding part of the data center in a hospital network. Three newracks of equipment need to be added, with an HP Comware 5820 series switch at the top of eachrack. The Comware 5820 series switch needs to connect back to two coreComware 12600switches using 10Gb connections. The distance between the three racks and the Comware 12500switches is approximately 40 meters; however, the network administrator is concerned aboutelectromagnetic and other types of interferences to electrical signals Which solutions protect against interference and are cost-effective for this scenario? (Select two.) A. 10GBase-ZR B. 10GBase-ER C. 10GBase-SR D. 10GBase-T

HP HP2-Z26 Exam


E. 10GBase-LX4

Answer: C,E

Explanation:


Switch 1 and 2 are HP Provision switches. VLAN 33 has been defined as the management VLANon both switches. Switch 1 is a layer 2 switch, and switch 2 is a layer 3 switch, with routingconfigured. Based on this topology, which management connections to Switch 1 are out-of-band? (Select two) A. User4 B. User-1 C. User-3 D. Switch 2 E. User-2

Answer: A,C

Explanation:

QUESTION NO: 34 A network administrator executes the following command:

HP HP2-Z26 Exam


What is the state of the VLAN 1 interface? A. All interfaces in VLAN 1 are down. B. The IP address of VLAN 1 conflicts with another device in VLAN 1. C. The IP address for VLAN 1 is a duplicate of another VLAN interface on the switch. D. VLAN 1 has a single port in a down state.

Answer: D

Explanation:


HP HP2-Z26 Exam


Assume the network shown in the exhibit has implemented RSTP Based on the topology, whichports are root ports? (Select two) A. SwitchA port 2 B. SwitchB port 2 C. SwitchB port 1 D. SwitchD port 2 E. SwitchC port 2

Answer: D,E

Explanation:

QUESTION NO: 36 Which item is different between the IEEE 802.3z and 802.3ae standards? A. Link aggregation B. Frame sizes C. Support of copper and fiber cabling D. Duplexing

Answer: C

Explanation:

QUESTION NO: 37 Which console cable is used on an HP Comware switch? A. Straight-through B. Cross-over C. USB D. Rollover

Answer: D

Explanation:

QUESTION NO: 38

HP HP2-Z26 Exam


A network administrator is connected to the console of an HP Comware switch when thesemessages display:

Based on this information, what has just occurred? A. A 10 GbE line card was inserted into the slot of the Comware switch. B. Another member has joined the IRF topology. C. The main processor card on a 7500 switch has become active. D. The second processor card on a 5820 switch has become active.

Answer: A

Explanation:

QUESTION NO: 39 A VLAN is connected to an HP Comware hybrid port. What can a network administrator use toassign a device to the VLAN? (Select two.) A. IP address B. Access Control List (ACL) C. IPX address D. Protocol E. LLDP device type

Answer: A,D

Explanation:

QUESTION NO: 40 HOTSPOT

HP HP2-Z26 Exam


Identify the port types that can be configured for HP Provision and HP Comware switches.(Options can be used more than once.)

Answer:

Explanation:

VLAN hybrid port – comware only

HP HP2-Z26 Exam


VLAN trunk port/ tagged port – comware and provision

VLAN access port/untagged port – comware and provision

QUESTION NO: 41 What are the participants in the 802 1X authentication process? (Select two.) A. Supplicant B. Client C. Access point (AP) D. Intermediary E. Authenticator

Answer: A,EReference: https://supportforums.adtran.com/docs/DOC-4240

QUESTION NO: 42 Refer to the network and ARP table exhibit.

The user on the left side of the exhibit wants to build a connection to the server on the rightAssume that SwitchA and SwitchB are HP Comware switches. For which IP address does theuser generate an ARP?

HP HP2-Z26 Exam


A. The user generates an ARP for the MAC address that corresponds to 10.1.11.1. B. The user generates an ARP for the MAC address that corresponds to 10.1.12.1. C. The user generates an ARP for the MAC address that corresponds to 10.1.12.2. D. The user generates an ARP for the MAC address that corresponds to 10.1.1111.

Answer: D

Explanation:

QUESTION NO: 43 A network administrator wants to redirect log messages on the HP Comware switches to a syslogserver. Which configuration implements the desired result?

A. Option A B. Option B C. Option C D. Option D

Answer: D

Explanation:

QUESTION NO: 44 Which HP Provision and HP Comware commands restore a configuration file from a TFTP serverto the switches' flash? (Select two.) A. Copy tftp config config.cfg 10.1.1.1 config.cfg pc B. Copy tftp 10.1.1.1 config.cfgconfigconfig.cfg pc C. Copy tftp://10.1.1.1/config.cfg flash: D. Restore tftp://10.1.1.1/startup-configuration config.cfg E. Restore startup-configuration from 10.1.1.1 config.cfg

Answer: A,E

HP HP2-Z26 Exam


Explanation:

QUESTION NO: 45 What is the function of HP Intelligent Provisioning? A. Secures access control at the edge of a network so that guest users are isolated B. Uses application templates to configure virtual networks, servers, and storage using industrybest practices C. Enables quick and secure implementation of a wireless network D. Deploys, configures, and maintains HP ProLiant Gen8 servers

Answer: DReference: http://h18013.www1.hp.com/products/servers/management/intelligentprovisioning/

QUESTION NO: 46 Refer to the partial command output.

Based on this output, which statement is true? A. Static LACP is used, and load sharing is functioning. B. Dynamic LACP is used, and load sharing has failed. C. Static LACP is used, and load sharing has failed. D. Dynamic LACP is used, and load sharing is functioning.

HP HP2-Z26 Exam


Answer: D

Explanation:

QUESTION NO: 47 A network administrator receives a new HP Provision switch and notices that the software versionrunning on the switch is older than what is currently used in the network. The networkadministrator copies an updated version of the operating system from the new switch's USB portto the secondary flash location. The network administrator then executes the following command: ProVision # boot system flash secondary The switch reboots using the new operating system. However, when the network administratorturns off the switch and turns it back on, the switch boots from the old operating system. Whichsolution should the network administrator use to fix the problem? A. Execute the startup-default secondary command. B. Execute the boot-loader file command. C. Execute the boot set-default flash secondary command. D. Boot into the switch's Monitor ROM Console and perform the upgrade a second time. E. Execute the startup-boot secondary command

Answer: C

Explanation:

QUESTION NO: 48 Which IMC agent starts and stops the IMC server and allows a network administrator to view thestatus of the IMC processes? A. Administration Deployment Agent (ADA) B. Policy Administration Agent (PAA) C. Deployment Monitoring Agent (DMA) D. IMC Processing Agent (IPA)

Answer: C

Explanation:

HP HP2-Z26 Exam


QUESTION NO: 49 A network administrator configures the following information on an HP Provision switch: Provision(config)# spanning tree Provision(config)# spanning tree instance 0 priority 2 Based on this information, what is the priority assigned to this switch for instance 0? A. 9 B. 2 C. 4096 D. 8192 E. 16384

Answer: D

Explanation:

QUESTION NO: 50 A network administrator enables debug to troubleshoot an OSPF adjacency on an HP Comwareswitch. The network administrator then disables and then re-enables an interface connected toanother switch running OSPF. After waiting for a few minutes, no output displays on the console. Which action must the network administrator take to resolve this problem? A. Execute the terminal logging command B. Restart the OSPF process. C. Re-initialize OSPF on the respective interface. D. Execute the terminal debugging command.

Answer: B

Explanation:

QUESTION NO: 51 What are factory default configuration settings of the HP MSM access points (APs)? (Select two.)

HP HP2-Z26 Exam


A. Password of admin B. DHCP client C. Autonomous mode D. Username of hp E. DHCP server

Answer: A,D

Explanation:

QUESTION NO: 52 A network administrator is setting up OSPF between an HP Provision and HP Comware switch.Once the configuration is finished, the network administrator sees log messages in the Comwaresession about the successful establishment of the adjacency. However, the network administratordoes not see similar messages on the Provision console. How can the network administrator see these log messages about the new OSPF adjacencies onthe Provision console? A. Use the show event-log command. B. Use the terminal logging command. C. Use the terminal monitor command. D. Use the show logging command.

Answer: A

Explanation:

QUESTION NO: 53 Which HP technology includes server provisioning, monitoring, diagnostics, and support? A. Intelligent Management Center B. Intelligent Resilient Framework C. Insight Remote Support D. iLO Management Engine

Answer: DReference:http://h20000.www2.hp.com/bc/docs/support/SupportManual/c03488111/c03488111.pdf (page 3,see the paragraph right under the bulleted point)

HP HP2-Z26 Exam


QUESTION NO: 54 Which modules provide connectivity for blade servers installed in the HP BladeSystem c-Classenclosure to external switches? (Select two.) A. Virtual Connect module B. MSR900 module C. 8200zl module D. HP 6120XG module E. 5830AF module

Answer: A,D

Explanation:

QUESTION NO: 55 Which standards do HP products support for Power over Ethernet (PoE)? A. 802.1ah B. 802 3af C. 802.3at D. 802.1az E. 802.3av

Answer: B,CReference:http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c02613461/c02613461.pdf (page1, overview, second para)

HP HP2-Z26 Exam
