How to Install AIX 5L

8/3/2019 How to Install AIX 5L

1/27

10/4/11 2:ow to install AIX 5L

Page 1ttp://www.ibm.com/developerworks/aix/library/au-install-aix.html

Sign in (or register)English

Technical topics Evaluation software Community Events

How to install AIX 5L

Shiv Dutta ([email protected]), Technical consultant, IBM, Software Group

Summary: Get step-by-step instructions for a number of generic AIX system setup procedures. These instructions should work for any ofthe AIX 5L releases. Variations, if any, should be minor.

Date: 31 Aug 2005Level: IntermediateAlso available in: Russian

Activity: 53835 viewsComments: 1 (View | Add comment - Sign in)

Average rating (72 votes)

Rate this article

Introduction

This article does not cover configurations that exploit the advanced technology features of POWER5 hardware, such as virtualization (virtI/O, Virtual Ethernet, and Micro-Partitioning) and Simultaneous Multi-Threading. For instructions on how to set up systems involving thefeatures, please refer to the articles listed under Resources section.

The following procedures are covered in this article:

Perform a new and complete overwrite BOS installation from CDPerform a nonprompted new and complete overwrite BOS installation from CDPerform a migration BOS installation from CDClone a rootvg using alternate disk installation

Configure Network Installation Manager (NIM) using EZNIMInstall a client using NIMInstall AIX from a Linux server using NIM on LinuxCreate a system backup to tapeClone a system using a system backup tapeClean up a failed software installationInstall AIX on a partition using HMC and a CD-ROM deviceInstall AIX on a partition without an HMC using the CD-ROM device

Perform a new and complete overwrite BOS installation from CD

Note:Before you perform this step, make sure you have reliable backups of your data and any customized applications or volume groups. Thinstructions on how to create a system backup are described later in this article.

Using this scenario, you can install the AIX operating system for the first time or overwrite an existing version of the operating system. Thisscenario involves the following steps:

Step 1. Prepare your system

There must be adequate disk space and memory available. AIX 5L Version 5.2 and AIX 5L Version 5.3 require 128MB of memory an2.2GB of physical disk space.Make sure your hardware installation is complete, including all external devices.If your system needs to communicate with other systems and access their resources, make sure you have the information in the followiworksheet before proceeding with the installation:


2/27



Network Attribute Value

Network interface For example: en0, et0

Host name

IP address

Network mask

Nameserver

Domain name

Gateway

Step 2. Boot from the AIX product CD

1. Insert the AIX Volume 1 CD into the CD-ROM device.2. Make sure all external devices attached to the system, such as CD-ROM drives, tape drives, DVD drives, and terminals, are turned on

Only the CD-ROM drive from which you will install AIX should contain the installation media.3. Power on the system.4. When the system beeps twice, press F5 on the keyboard or 5 on an ASCII terminal. If you have a graphics display, you will see the

keyboard icon on the screen when the beeps occur. If you have an ASCII terminal, you will see the word keyboard when the beeps occ5. Select the system console by pressing F1 or 1 on an ASCII terminal and press Enter.6. Select the English language for the BOS installation menus by typing a 1 in the Choice field. Press Enter to open the Welcome to B

Operating System Installation and Maintenance screen.7. Type 2 to select 2 Change/Show Installation Settings and Install in the Choice field and press Enter.

Welcome to Base Operating SystemInstallation and Maintenance

Type the number of your choice and press Enter. Choice isindicated by >>>.

1 Start Install Now with Default Settings

2 Change/Show Installation Settings and Install

3 Start Maintenance Mode for System Recovery

88 Help ?99 Previous Menu

>>> Choice [1]: 2

Step 3. Set and verify BOS installation settings

1. In the Installation and Settings screen, verify that the installation settings are correct by checking the method of installation (new andcomplete overwrite), the disk or disks you want to install, the primary language environment settings, and the advanced options.

If the default choices are correct, type 0 and press Enter to begin the BOS installation. The system automatically reboots afterinstallation is complete. Go to Step 4. Configure the system after installation.

Otherwise, go to sub-step 2.2. To change the System Settings, which includes the method of installation and disk where you want to install, type 1 in the Choice fiel

and press Enter.

Installation and Settings

Either type 0 and press Enter to install with current settings,or type the number of the setting you want to changeand press Enter.

1 System Settings:Method of Installation..................New and Complete OverwriteDisk Where You Want to Install..hdisk0


3/27



>>> Choice [0]: 1

3. Type 1 for New and Complete Overwrite in the Choice field and press Enter. The Change Disk(s) Where You Want to Install screnow displays.

Change Disk(s) Where You Want to Install

Type one or more numbers for the disk(s) to be used forinstallation and press Enter. To cancel a choice, type thecorresponding number and Press Enter. At least onebootable disk must be selected. The current choice isindicated by >>>.

Name Location Code Size(MB) VG Status Bootable

1 hdisk0 04-B0-00-2,0 4296 None Yes2 hdisk1 04-B0-00-5,0 4296 None Yes3 hdisk2 04-B0-00-6,0 12288 None Yes

>>> 0 Continue with choices indicated above

66 Disks not known to Base Operating System Installation77 Display More Disk Information88 Help ?

99 Previous Menu

>>> Choice [0]:

4. In the Change Disk(s) Where You Want to Install screen:a. Select hdisk0 by typing a 1 in the Choice field and press Enter. The disk will now be selected as indicated by >>>. To unselect

the destination disk, type the number again and press Enter.b. To finish selecting disks, type a 0 in the Choice field and press Enter. The Installation and Settings screen now displays with

selected disks listed under System Settings.5. Change the Primary Language Environment Settings to English (United States). Use the following steps to change the Cultural

Convention, Language, and Keyboard to English.a. Type 2 in the Choice field on the Installation and Settings screen to select the Primary Language Environment Settings

option.b. Type the number corresponding to English (United States) as the Cultural Convention in the Choice field and press Enter.c. Select the appropriate keyboard and language options.

You do not need to select the More Options selection, because you are using the default options in this scenario. For more informatioabout the installation options available in AIX 5.2 and greater, see Installation Options in the AIX 5L Version 5.3 Installation Guide aReference.

6. Verify that the selections are correct in the Overwrite Installation Summary screen, as follows:

Overwrite Installation Summary

Disks: hdisk0Cultural Convention: en_USLanguage: en_USKeyboard: en_US64 Bit Kernel Enabled: No

JFS2 File Systems Created: NoDesktop: CDEEnable System Backups to install any system: Yes

Optional Software being installed:

>>> 1 Continue with Install88 Help ?99 Previous Menu

>>> Choice [1]:


4/27



7. Press Enter to begin the BOS installation. The system automatically reboots after installation is complete.

Step 4. Configure the system after installation

1. After a new and complete overwrite installation, the Configuration Assistant opens on systems with a graphics display. On systems wan ASCII display, the Installation Assistant opens.

2. Select the Accept Licenses option to accept the electronic licenses for the operating system.3. Set the date and time, set the password for the administrator (root user), and configure the network communications (TCP/IP).

Use any other options at this time. You can return to the Configuration Assistant or the Installation Assistant by typing configassistsmitty assist at the command line.

4. Select Exit the Configuration Assistant and select Next. Or, press F10 or ESC+0 to exit the Installation Assistant.5. If you are in the Configuration Assistant, select Finish now. Do not start the Configuration Assistant when restarting AIX and select

Finish.

At this point, the BOS Installation is complete, and the initial configuration of the system is complete.

Perform a nonprompted new and complete overwrite BOS installation from CD

Using this scenario, you can perform a nonprompted new and complete overwrite BOS installation from CD. The first time you install, theBOS installation program presents menus from which you must choose setup options.

For subsequent installations, you can change many aspects of the default BOS installation program by editing the bosinst.data file. The

bosinst.data file directs the actions of the BOS installation program. The file resides in the /var/adm/ras directory on the installed machineonly, and it is not accessible on the commercial tape or the CD on which you received AIX 5L Version 5.3.

Also, the bosinst.data file can be used to replicate one set of installation settings on other machines. For example, system administrators cancreate a bosinst.data file with settings that can be used to install all the machines they support that have the same configuration.

In this scenario, you will create a bosinst.data file that will not prompt the user during the BOS installation menus.

This scenario involves the following steps:

Create a customized bosinst.data fileCreate a supplementary disketteBoot from the AIX product CD

Note:

If you are overwriting an existing system, gather the TCP/IP information from the system before you begin this scenario. Also, before youperform a new and complete overwrite installation, make sure you have reliable backups of your data and any customized applications orvolume groups. The instructions on how to create a system backup are described elsewhere in this article.

Create a customized bosinst.data file

1. Use the cd command to change your directory to the/var/adm/ras directory.2. Copy the/var/adm/ras/bosinst.data file to a new name, such as bosinst.data.orig. This step preserves the original bosinst.data file.3. Edit the bosinst.data file with an ASCII editor, as follows:

Note: The following example includes automatic acceptance of software license agreements.

control_flow:CONSOLE = /dev/lft0INSTALL_METHOD = overwritePROMPT = noPROMPT = noEXISTING_SYSTEM_OVERWRITE = yesINSTALL_X_IF_ADAPTER = yesRUN_STARTUP = yesRM_INST_ROOTS = noERROR_EXIT =CUSTOMIZATION_FILE =TCB =INSTALL_TYPE = fullBUNDLES =


5/27



SWITCH_TO_PRODUCT_TAPE = noRECOVER_DEVICES = yesBOSINST_DEBUG = noACCEPT_LICENSES = yesINSTALL_64BIT_KERNEL =INSTALL_CONFIGURATION =DESKTOP = CDE

target_disk_data:LOCATION =SIZE_MB =

HDISKNAME = hdisk0

localeBOSINST_LANG = en_USCULTURAL_CONVENTION = en_USMESSAGES = CKEYBOARD = en_US

4. Verify the contents of the edited bosinst.data file using the bicheck command:

/usr/lpp/bosinst/bicheck bosinst.data

5. Copy the edited file to the root directory:

cp /var/adm/ras/bosinst.data /bosinst.data

Create a supplementary diskette

1. Create an ASCII file consisting of one word:

data

2. Save the new ASCII file and name it signature.3. Copy the signature file to the root directory.4. Create the supplementary diskette and use it for installation. Back up the edited bosinst.data file and the new signature file to the

diskette with the following command:

ls ./bosinst.data ./signature | backup -iqv

Boot from the AIX product CD

1. Insert the diskette in the diskette drive of the target machine you are installing.2. Insert the AIX Volume 1 CD in the CD-ROM drive.3. Boot the system.

Rather than the default bosinst.data file shipped with the installation media to answer the questions in the BOS menus, the BOS installationprogram uses the customized bosinst.data file on the diskette. If you filled in the values correctly in the bosinst.data file, the BOS installatiwill begin. If the BOS installation program detects an error with a value in the bosinst.data file, the BOS menus will display with a messageexplaining what information needs to be corrected.

Perform a migration BOS installation from CD

Note:If you are overwriting an existing system, gather the TCP/IP information before you begin this scenario. Also, before you perform a migratioinstallation, make sure you have reliable backups of your data and any customized applications or volume groups. The instructions on how tocreate a system backup are described later in this article.

Using this scenario, you can migrate a system from AIX 4.3.3 (or later) to AIX 5.3.

Step 1. Prepare for the migration


6/27



Before starting the migration, complete the following prerequisites:

1. Ensure that the root user has a primary authentication method of SYSTEM. You can check this condition by typing the followingcommand:

# lsuser -a auth1 root

If needed, change the value by typing the following command:

# chuser auth1=SYSTEM root

2. Before you begin the installation, other users who have access to your system must be logged off.3. Verify that your applications will run on AIX 5L Version 5.3. Also, check if your applications are binary compatible with AIX 5L

Version 5.3. For details on binary compatibility, check out the AIX 5L Version 5 binary compatibility Web site. If your system is anapplication server, verify that there are no licensing issues. Refer to your application documentation or provider to verify on which levof AIX your applications are supported and licensed. You can also check the AIX application availability guide.

4. Check that your hardware microcode is up to date.5. All requisite hardware, including any external devices, such as tape drives or CD/DVD-ROM drives, must be physically connected an

powered on.6. Use the errpt command to generate an error report from entries in the system error log. To display a complete detailed report, type the

following:

# errpt -a

7. There must be adequate disk space and memory available. AIX 5L Version 5.3 requires 128MB of memory and 2.2GB of physical disspace.

8. Run the pre-migration script located in the mount_point/usr/lpp/bos directory on your CD. To mount the CD, run the followingcommand:

# mount -v cdrfs -o ro /dev/cdN /mnt

where "N" is your CD drive number.9. Make a backup copy of your system software and data. The instructions on how to create a system backup are described elsewhere in

article.10. Always refer to the release notes for the latest migration information.


1. If they are not already on, turn on your attached devices.2. Insert the AIX Volume 1 CD into the CD-ROM device.3. Reboot the system by typing the following command:

# shutdown -r

4. When the system beeps twice, press F5 on the keyboard or 5 on an ASCII terminal. If you have a graphics display, you will see thekeyboard icon on the screen when the beeps occur. If you have an ASCII terminal, you will see the word keyboard when the beeps occ

5. Select the system console by pressing F1 or 1 on an ASCII terminal and press Enter.6. Select the English language for the BOS installation menus by typing a 1 at the Choice field and press Enter. The Welcome to Base

Operating System Installation and Maintenance menu opens.7. Type 2 to select Change/Show Installation Settings and Install in the Choice field and press Enter.







7/27




>>> Choice [1]: 2

Step 3. Verify migration installation settings and begin installation

1. Verify that migration is the method of installation. If migration is not the method of installation, select it now. Select the disk or disksyou want to install.

1 System Settings:Method of Installation....................MigrationDisk Where You Want to Install............hdisk0

2. Select Primary Language Environment Settings after install.3. Type 3 and press Enter to select More Options. To use the Help menu to learn more about the options available during a migration

installation, type 88 and press Enter in the Installation Options menu. For more information about the installation options available iAIX 5L Version 5.3, see Installation Options in the AIX 5L Version 5.3 Installation Guide and Reference.

4. Verify the selections in the Migration Installation Summary screen and press Enter.5. When the Migration Confirmation menu displays, follow the menu instructions to list system information or continue with the migrati

by typing 0 and pressing Enter.

Migration Confirmation

Either type 0 and press Enter to continue the installation,or type the number of your choice and press Enter.

1. List the saved Base System configuration files whichwill not be merged into the system. These files aresaved in /tmp/bos.

2. List the filesets which will be removed and not replaced.3. List directories which will have all current contents

removed.4. Reboot without migrating.

Acceptance of license agreements is required before usingsystem. You will be prompted to accept after the systemreboots.

>>> 0 Continue with the migration.88 Help ?

------------------------------------------------------------

WARNING: Selected files, directories, and filesets(installable options) from the Base System will be removed.Choose 2 or 3 for more information.

>>> Choice[0]:

Step 4. Verify system configuration after installation

After the migration is complete, the system will reboot. Verify the system configuration, as follows:

1. After a migration installation, the Configuration Assistant opens on systems with a graphics display. And after a migration installationthe Installation Assistant opens on systems with an ASCII display.

For more information about the Configuration Assistant or the Installation Assistant, see the Configuring the Operating Systemsectionthe AIX 5L Version 5.3 Installation Guide and Reference.

2. Select the Accept Licenses option to accept the electronic licenses for the operating system.3. Verify the administrator (root user) password and network communications (TCP/IP) information.

Use any other options at this time. You can return to the Configuration Assistant or the Installation Assistant by typing configassistsmitty assist at the command line.

4. Select Exit the Configuration Assistant and select Next. Or, press F10 or ESC+0 to exit the Installation Assistant.


8/27



5. If you are in the Configuration Assistant, select Finish now. Do not start the Configuration Assistant when restarting AIX and selectFinish.

6. When the login prompt displays, log in as the root user to perform system administration tasks.7. Run the/usr/lpp/bos/post_migration script.

Clone a rootvg using alternate disk installation

Using this scenario, you can clone AIX running on rootvg to an alternate disk on the same system, install a user-defined software bundle, andrun a user-defined script to customize the AIX image on the alternate disk. Because the alternate disk installation process involves cloning anexisting rootvg to a target alternate disk, the target alternate disk must not be already assigned to a volume group.

For information about alternate disk installation, see AIX 5L Version 5.3 Installation Guide and Reference.

Step 1. Prepare for the alternate disk installation

1. Check the status of physical disks on your system. Type:

# lspv

Output similar to the following displays:

hdisk0 0009710fa9c79877 rootvg activehdisk1 0009710f0b90db93 None

You can use hdisk1 as our alternate disk because no volume group is assigned to this physical disk.

2. Check to see if the alt_disk_install fileset has been installed by running the following (Note: This command is obsolete in AIX 5LVersion 5.3. It has been replaced by alt_disk_copy, alt_disk_mksysb, and alt_rootvg_op.):

# lslpp -L bos.alt_disk_install.rte

Output similar to the following displays if the alt_disk_install fileset is not installed:

lslpp: 0504-132 Fileset bos.alt_disk_install.rte not installed.

3. Using Volume 1 of the AIX installation media, install the alt_disk_install fileset by running the following:

# geninstall -d/dev/cd0 bos.alt_disk_install.rte


+-------------------------------------------------------------+Summaries

+-------------------------------------------------------------+

Installation Summary---------------------------------------------------------------Name Level Part Event Result---------------------------------------------------------------bos.alt_disk_install.rte 5.3.0.0 USR APPLY SUCCESS

4. Create a user-defined bundle called/usr/sys/inst.data/user_bundles/MyBundle.bndthat contains the following filesets:

I:bos.content_listI:bos.games


9/27



For more information on how to create a user-defined software bundle, see AIX 5L Version 5.3 Installation Guide and Reference.

5. Create the/home/scripts directory:

mkdir /home/scripts

6. Create a user-defined customization script called AddUsers.sh in the/home/scripts directory:

touch /home/scripts/AddUsers.shchmod 755 /home/scripts/AddUsers.sh

7. Edit/home/scripts/AddUsers.sh to contain the following lines:

mkuser johndoetouch /home/johndoe/abc.txttouch /home/johndoe/xyz.txt

Step 2. Perform the alternate disk installation and customization

1. To clone the rootvg to an alternate disk, type the following at the command line to open the SMIT menu:

# smit alt_clone

2. Select hdisk1 in the Target Disk to Install field.3. Select the MyBundle bundle in the Bundle to Install field.4. Insert Volume 1 of the installation media.5. Type/dev/cd0 in the Directory or Device with images field.6. Type/home/scripts/AddUsers.sh in the Customization script field.7. Press Enter to start the alternate disk installation.8. Check that the alternate disk was created by running the following:

# lspv


hdisk0 0009710fa9c79877 rootvghdisk1 0009710f0b90db93 altinst_rootvg

Step 3. Boot from the alternate disk

1. By default, the alternate disk installation process changes the boot list to the alternate disk. To check this, run the following:

# bootlist -m normal -o


hdisk1

2. Reboot the system. Type:

# shutdown -r

The system boots from the boot image on the alternate disk (hdisk1).

Step 4. Verify the operation

1. When the system reboots, it will be running off the alternate disk. To check this, type the following:


10/27


11/27



In this scenario you will do the following:

1. Perform an BOS (rte) installation.2. Use a bosinst_data resource to perform a nonprompted installation. For information on how to create a bosinst.data file for

nonprompted installation, see Perform a nonprompted new and complete overwrite BOS installation from CD.3. Use a resolv_confresource to configure the network nameserver and domain.

You should first perform a system backup on the client to ensure safe system recovery. For more details, see Create a system backup to tape

1. Type the following:

# smit nim_bosinst

2. Select a target for the BOS installation operation.3. Select rte installation for the installation type.4. Select the lpp_source resource for the BOS installation.5. Select the SPOT resource for the BOS installation.6. Select the BOSINST_DATA to use during installation option and select a bosinst_data resource that is capable of performing a

nonprompted BOS installation.7. Select the RESOLV_CONF to use for network configuration option and select a resolv_confresource.8. Select the Accept New License Agreements option and select Yes.9. Accept the default values for the remaining menu options.

10. Press Enter to confirm and begin the NIM client installation.

11. To check the status of the NIM client installation, type:# lsnim -l va09


va09:

class = machinestype = standalonedefault_res = basic_res_grpplatform = chrpnetboot_kernel = upif1 = master_net va09 0

cable_type1 = bncCstate = Base Operating System installation is

being performed.prev_state = BOS installation has been enabled.Mstate = in the process of bootinginfo = BOS install 7% complete : 0% of operations

completed.boot = bootbosinst_data = bid_tty_owlpp_source = 520lpp_resnim_script = nim_scriptresolv_conf = master_net_confspot = 520spot_rescpuid = 0009710F4C00control = masterCstate_result = success

Install AIX from a Linux server using NIM on Linux

NIM on Linux (NIMOL) provides basic AIX software administration services from a Linux server. The NIMOL RPM included in the AIXproduct media provides basic NIM functionality for a Linux server. While using a pSeries NIM server for AIX client management providemore functionality, NIMOL provides the following functions on Linux servers:

Configuring services required to install AIX with NIMPerforming a network installation of AIX


12/27



Installing software updates on an AIX systemListing software installed on an AIX systemCreating a backup of an AIX system that NIMOL can use to install other systems with NIM

NIMOL is supported on SUSE LINUX 9.0 and Red Hat 9.0. Read the NIMOL readme file in the/usr/share/doc/nimol directory forinformation on updates.

Note:NIMOL supports AIX 5L Version 5.2 with the 5200-04 Recommended Maintenance package and later.

Commands

The following commands are shipped with the NIMOL RPM:

nimol_config

Configures a Linux server to install AIX with NIMnimol_install

Sets up a client for AIX installationnimol_lslpp

Lists software installed on an AIX clientnimol_update

Installs software updates onto an AIX clientnimol_backup

Creates an installable backup of an AIX client

Note:These commands are available on the Linux server. For additional information on these commands, run the man command on the Linux servwith the name of the specific NIMOL command.

Configuring the Linux server

To configure the Linux server, complete the following:

1. Insert the AIX product CD that contains the NIMOL RPM into the Linux server.2. Install the following RPMs, which are requisite for SUSE LINUX 9.0 and Red Hat 9.0:

dhcptftpnfs-utils

gettext

The following RPMs are additional requisites for Red Hat 9.0 only:

dhcp-servertftp-server

3. Insert the AIX product CD Volume 1 into the Linux server.4. Install the NIMOL RPM by running the following commands:

mount /dev/cdromrpm -ivh /mnt/cdrom/RPMS/linux/nimol*

5. Run the following command to configure the Linux server:

nimol_config -C

The nimol_config command configures the basic services required to install AIX on clients with NIM, such as bootp, tftp, nfs, and syslog. Tcommand uses the dhcp server to respond to client bootp requests.

Note:You should not manually modify the/etc/dhcpd.conffile because the modifications might interfere with the ability of NIMOL to add andremove subnet and host entries.

Creating AIX installation resources


13/27



To create AIX installation resources, you need access to an existing AIX client.

1. Make sure that your NIMOL Linux server has rhost permissions to the AIX client by editing the/.rhosts file on the AIX client.2. Run the nimol_backup command on the Linux server. For example, if the client is named myaixclient.ibm.com and you want to name

the installation resources aix530, then run the following command:

nimol_backup -c myaixclient.ibm.com -L aix530

The nimol_backup command creates a mksysb backup of the client, as well as the other resources required to perform a network boot the /export/aix/aix530 directory.

Alternately, you can use the nimol_config command to define existing AIX installation resources that reside on your NIMOL server.For example, if you have existing AIX installation resources located in /export/aix/aix530, run the following command to define theresources for use with NIMOL:

nimol_config -t /export/aix -L aix530

Setting up a NIMOL client

You can set up a client for the installation of AIX with NIM by running the nimol_install command. Before you run the nimol_install

command, you will need the following information for the client:

HostnameMAC addressSubnet mask

The following examples show how to obtain your MAC address.

To obtain the MAC address for the ent0 network adapter on a running client, run the following command:

lscfg -vl ent0

To obtain the MAC address on an IBM eServer pSeries client that is not running, complete the following:

1. Power on the system.2. Press F1 when the keyboard icon is displayed to access the SMS menus.3. Select Boot Options.4. Select Install or Boot a Device.5. Select Network. This menu refers to your network card (for example, ethernet).6. Select Information. This screen will contain the MAC address.

When specifying the MAC address to nimol_install, colons are required.

For example, to set up a client with a client1 hostname, 255.255.255.0 subnet mask, 192.168.1.1 gateway, and 00:60:08:3F:E8:DF MACaddress with the "aix530" installation resources, run the following command:

nimol_install -c client1 -g 192.168.1.1 -m 00:60:08:3F:E8:DF \-s 255.255.255.0 -L aix530

After you run nimol_install, you can specify a network boot using the bootlist command on a running AIX system. For example, if theclient installs AIX from the ent0 adapter with a 192.168.1.20 client IP address, and the NIMOL server has a 192.168.1.10 IP address and is othe same subnet as the client, complete the following:

1. Run the bootlist command as follows:

bootlist -m normal ent0 bserver=192.168.1.10 gateway=0.0.0.0 \


14/27



client=192.168.1.20

2. Run the following command to begin the installation:

shutdown -Fr

Note:If the client is not running, power on the system and enter the System Management Services (SMS) menus by pressing F1 when the

keyboard icon is displayed. You can then specify the network boot parameters and select the network device as the boot device.

The syslog daemon is configured to receive remote status by default. This setting allows you to monitor the installation by viewing the/var/log/nimol.log file on the NIMOL server.

After the installation is complete, you can remove the setup for the client named client1 by running the following command:

nimol_install -c client1 -r

Maintaining the NIMOL client

You can use the following commands to maintain the NIMOL client:

nimol_update

nimol_lslpp

Note: The default option for the nimol_install command is intended for use on the client machine where you installed AIX. If you specifythe -n option with the nimol_install command when you install AIX on the client machine, these commands will not be available.

The following scenarios are tasks involved in maintaining the NIMOL client:

To list the software that is installed on client1, run the following command:

nimol_lslpp -c client1 -f "-L"

To install the perl.rte software package from the aix530 installation resources, run the following command:

nimol_update -c client1 -L aix530 -p "perl.rte"

1. To install additional software, copy the installp images into the lpp_source/installp/ppc sub-directory of the installation resourcesdirectory. For example, if your installation resources are located in the /export/aix/aix530 directory, you will need to copy the installpimages into the/export/aix/aix530/lpp_source/installp/ppcdirectory. You also must copy the .toc file because Linux machines canncreate this file.

2. To use a different remote access other than rhost permissions, you can specify the -moption with the nimol_update command, thenimol_lslpp command, or the nimol_backup command. The alternative remote access must be configured prior to using it with theNIMOL commands, and the remote access method cannot prompt for a password. For example, the following command will use the/usr/bin/ssh directory to remotely access client1 during a software listing:

nimol_lslpp -c client1 -f "-L" -m /usr/bin/ssh

Unconfiguring the NIMOL server

To unconfigure the NIMOL server, complete the following:

1. Determine if clients are set up to install by running the following command:

nimol_install -l


15/27



2. Remove any clients that are listed as set to install by running the following command:

nimol_install -r -c client

3. Remove the AIX installation resource labels that you created by running the following command:

nimol_config -r -L aix530

Removing these labels removes all resources from the NIMOL server. You can define them again if you decide to configure the NIMOserver in the future.

4. Unconfigure NIMOL by running the following command:

nimol_config -U

This command restores services to the state they were before you configured NIMOL. For example, if you had the nfs service and the service turned off prior to configuring NIMOL, then they are turned off again.

5. Remove the NIMOL RPM by running the following command:

rpm -e nimol

Create a system backup to tape

Using this scenario, you can create and verify a bootable system backup, also known as a root volume group backup or mksysb image.

Step 1. Prepare for system backup creation

Before creating system backups, complete the following prerequisites:

1. Be sure you are logged in as root user.2. If you plan to use a backup image for installing other differently configured target systems, you must create the image before configur

the source system, or set the RECOVER_DEVICES variable to no in the bosinst.data file. For more information about the bosinst.da

file, refer to Perform a new and complete overwrite BOS installation from CD.3. Consider altering passwords and network addresses if you use a backup to make master copies of a source system. Copying password

from the source to a target system can create security problems. Also, if network addresses are copied to a target system, duplicateaddresses can disrupt network communications.

4. Mount all file systems you want to back up. The mksysb command backs up only mounted JFS (Journaled File System) and JFS2(Enhanced Journaled File System) in the rootvg.

Note: The mksysb command does not back up file systems mounted across an NFS network.

5. Unmount any local directories that are mounted over another local directory.

Note: This backup procedure backs up files twice if a local directory is mounted over another local directory in the same file system. Fexample, if you mount /tmp over /usr/tmp, the files in the /tmp directory are then backed up twice. This duplication might exceed thenumber of files that a file system can hold, which can cause a future installation of the backup image to fail.

6. Use the/etc/exclude.rootvg file to list files you do not want backed up.7. Make at least 12MB of free disk space available in the /tmp directory. The mksysb command requires this working space for the durat

of the backup.

Use the df command, which reports in units of 512-byte blocks, to determine the free space in the /tmp directory. Use the chfs commto change the size of the file system, if necessary.

For example, the following command adds 12MB of disk space to the /tmp directory of a system with 4MB partitions:

# chfs -a size=+24000 /tmp


16/27



8. All hardware must already be installed, including external devices, such as tape and CD-ROM drives.9. The bos.sysmgt.sysbr fileset must be installed. The bos.sysmgt.sysbr fileset is automatically installed in AIX 5.3. To determine if the

bos.sysmgt.sysbr fileset is installed on your system, type:

# lslpp -l bos.sysmgt.sysbr

If the lslpp command does not list the bos.sysmgt.sysbr fileset, install it before continuing with the backup procedure. Type the

following:

# installp -agqXd /dev/cd0 bos.sysmgt.sysbr

Step 2. Create a system backup to tape

1. Enter the smit mksysb fast path.2. Select the tape device in the Backup DEVICE or File field.3. If you want to create map files, select Yes in the Create Map Files? field.

Note: If you plan to reinstall the backup to target systems other than the source system, or if the disk configuration of the source systemmight change before reinstalling the backup, do not create map files.

4. To exclude certain files from the backup, select Yes in the Exclude Files field.5. Select Yes in the List Files field as they are backed up.6. If you are running any other programs during the backup, select Yes in the Disable software packing of backup? field.7. Use the default values for the rest of the menu options.8. Press Enter to confirm and begin the system backup process.9. The COMMAND STATUS screen displays, showing status messages while the system makes the backup image. When the backup

process finishes, the COMMAND: field changes to OK.10. To exit SMIT when the backup completes, press F10 or Esc+0.11. Remove the tape and label it. Write-protect the backup tape.12. Record any root and user passwords that were backed up. Remember that these passwords become active if you use the backup to eith

restore this system or install another system.

You now have successfully created the backup of your rootvg. Because the system backup contains a boot image, you can use this tape to sta

your system if for some reason you cannot boot from hard disks.

Clone a system using a system backup tape

With a mksysb image, you can clone one system image onto multiple target systems. The target systems might not contain the same hardwadevices or adapters, require the same kernel (uniprocessor or multiprocessor), or be the same hardware platform as the source system.

Note: AIX 5L Version 5.3 does not support uniprocessor kernel.

Beginning in AIX 5L Version 5.2, all devices and kernel support are installed by default during the BOS installation process. If the EnableSystem Backups to install any system selection in the Install Software menu was set to Yes, you can create a mksysb image that boots andinstalls supported systems. Verify that your system is installed with all devices and kernel support by typing the following:

# grep ALL_DEVICES_KERNELS /var/adm/ras/bosinst.data


ALL_DEVICES_KERNELS = yes

Use this scenario if your system was not installed with all devices and kernel support during BOS installation. Be sure to boot from the


17/27



appropriate product media for your system and at the same maintenance level of BOS as the installed source system on which the mksysb wmade. For example, use BOS AIX 5.3 media with a mksysb from a BOS AIX 5.3 system. Use this how-to when installing a system backuptape to a different system.

In this scenario, you will do the following:

1. Boot the system with the AIX Volume 1 CD in the CD-ROM drive and the system backup tape in the tape device.2. Select Start Maintenance Mode for System Recovery.3. Select Install from a system backup.4. Select the drive containing the backup tape and press Enter.

The system reads the media and begins the installation.

You are then prompted for the BOS installation language and the Welcome screen displays. Continue with the prompted installation, becacloning is not supported in nonprompted installations.

If you are cloning from the product CD to restore a backup tape, do not remove the CD from the CD-ROM drive.

After the mksysb installation completes, the installation program automatically installs additional devices and the kernel (uniprocessor ormultiprocessor) on your system using the original product media you booted from. Information is saved in the BOS installation log files. Toview the BOS installation log files, type cd /var/adm/ras and view the devinst.log file in this directory.

If the source system does not have the correct passwords and network information, you can make modifications on the target system now. Asome products (such as graPHIGS) ship device-specific files. If your graphics adapter is different on the target system, verify that the device

specific filesets for graphics-related LPPs are installed.

Clean up a failed software installation

Using this scenario, you can clean up software products and service updates after an interrupted or failed installation. The cleanup procedureattempts to delete items that were partially installed or left in an incomplete state. This scenario applies only to the update or installation ofoptional software products. If your AIX 5L Version 5.3 BOS installation was unsuccessful, see the AIX 5L Version 5.3 Installation Guide anReference.

Note: It is recommended that you first perform a system backup before installing software updates to ensure safe system recovery. See theCreate a system backup to tape.

The cleanup procedure attempts to revert the update to its previous state. For example, when cleaning up an update that was interrupted in th

COMMITTING state, the cleanup procedure attempts to return the update to its APPLIED state.

If an update installation is interrupted, run the lslpp -l command to see the current state of the update. For example, if you run lslpp -l oan interrupted update installation, it might report the update status as APPLYING rather than APPLIED.

If the interruption occurs during the initial state of an installation, then the cleanup procedure attempts to delete the installation entirely andrestore the previous version of the product (if there is one). When the previous version is restored, it becomes the active version. When theprevious version cannot be restored, the software is listed by the lslpp -l command as BROKEN.

When the product is deleted or BROKEN, you can attempt to reinstall the software. Any product in the BROKEN state cannot be cleaned uit can only be reinstalled or removed.

To initiate a cleanup procedure using SMIT:

1. Type smit maintain_software on the command line.

2. Select Clean Up After Failed or Interrupted Installation and press Enter.

To initiate a cleanup procedure from the command line, type installp -C on the command line and press Enter.

If prompted to reboot (restart) the system after running the cleanup procedure, then do so now.

If you get a message indicating that no products were found that could be cleaned up, you might have executed the cleanup procedure when iwas not needed. Try your installation again.

Install AIX on a partition using HMC and a CD-ROM device


18/27



Prerequisites

In this procedure, you will perform a new and complete AIX BOS installation on a logical partition using the partition's CD-ROM device. Thprocedure assumes that there is an HMC attached to the managed system.

Before you begin this procedure, you should have already used the HMC to create a partition and partition profile for the client. Assign theSCSI bus controller attached to the CD-ROM device, a network adapter, and enough disk space for the AIX operating system to the partitionSet the boot mode for this partition to be SMS mode. After you have successfully created the partition and partition profile, leave the partitioin the Ready state. For instructions about how to create a logical partition and partition profile, refer to the Creating logical partitions andpartition profiles article in the IBM eServer Hardware Information Center.

Step 1. Activate the partition

1. Activate the partitiona. Insert the AIX 5L Volume 1 CD into the CD device of the managed system.b. Right-click on the partition to open the menu.c. Select Activate. The Activate Partition menu opens with a selection of partition profiles. Be sure the correct profile is highlighted. Select Open a terminal window or console session at the bottom of the menu to open a virtual terminal (vterm) window.e. Select Advanced to open the Advanced options menu.f. For the Boot mode, select SMS.g. Select OK to close the Advanced options menu.h. Select OK. A vterm window opens for the partition.

Step 2. In the SMS menu on the vterm

1. In the SMS menu on the vterm, do the following:a. Press the 5 key and press Enter to select 5. Select Boot Options. PowerPC Firmware Version SF220_001 SMS 1.5 (c)

Copyright IBM Corp. 2000, 2003 All rights reserved. -----------------------------------------------------

---- Main Menu 1. Select Language 2. Setup Remote IPL (Initial Program Load) 3. Change SCSI Settings 4.

Select Console 5. Select Boot Options -----------------------------------------------------------

Navigation Keys: X = eXit System Management Services ----------------------------------------------------

----- Type the number of the menu item and press Enter or select Navigation Key: 5

b. Press the 2 key and press Enter to select 2. Select Boot Devices.c. Press the 1 key and press Enter to select 1. Select first Boot Device.d. Press the 3 key and press Enter to select 3. CD/DVD.e. Select the media type that corresponds to the CD-ROM device and press Enter.f. Select the device number that corresponds to the CD-ROM device and press Enter. The CD-ROM device is now the first devic

the Current Boot Sequence list.

g. Press the ESC key until you return to the Configure Boot Device Order menu.h. Press the 2 key to select 2. Select the second Boot Device.i. Press the 5 key and press Enter to select 5. Hard Drive.j. If you have more than one hard disk in your partition, determine which hard disk you will use to perform the AIX installation.

Select the media type that corresponds to the hard disk and press Enter.k. Select the device number that corresponds to the hard disk and press Enter.l. Press the x key to exit the SMS menu. Confirm that you want to exit SMS.

Step 3. Boot from the AIX 5L Volume 1

1. Boot from the AIX 5L Volume 1, as follows:a. Select Console and press Enter.b. Select Language for BOS installation menus and press Enter to open the Welcome to Base Operating System Installation

Maintenance menu.

c. Type 2 to select Change/Show Installation Settings and Install in the Choice field and press Enter.


Type the number of your choice and press Enter. Choiceis indicatedby >>>.





19/27




>>> Choice [1]: 2

Step 4. Verify or change BOS installation settings

1. Verify or change BOS installation settings, as follows:a. Type 1 in the Choice field to select the System Settings option.b. Type 1 for New and Complete Overwrite in the Choice field and press Enter.

Note:The installation methods available depend on whether your disk has a previous Version of AIX installed.

c. When the Change Disk(s) screen displays, you can change the destination disk for the installation. If the default shown is correctype 0 in the Choice field and press Enter. To change the destination disk, do the following:

1. Type the number for each disk you choose in the Choice field and press Enter. Do not press Enter a final time until youhave finished selecting all disks. If you must deselect a disk, type its number a second time and press Enter.

2. When you have finished selecting the disks, type 0 in the Choice field and press Enter. The Installation and Settingsscreen displays with the selected disks listed under System Settings.

d. If needed, change the primary language environment. Use the following steps to change the primary language used by thisinstallation to select the language and cultural convention you want to use.

Note:Changes to the primary language environment do not take effect until after the BOS installation has completed and your system rebooted.

1. Type 2 in the Choice field on the Installation and Settings screen to select the Primary Language Environment Settinoption.

2. Select the appropriate set of cultural convention, language, and keyboard options. Most of the options are a predefinedcombination; however, you can define your own combination of options.

To choose a predefined Primary Language Environment, type that number in the Choice field and press Enter.To configure your own primary language environment, do the following:

a. Select MORE CHOICES.b. Select Create Your Own Combination.c. When the Set Primary Cultural Convention screen displays, type the number in the Choice field that

corresponds to the cultural convention of your choice and press Enter.d. When the Set Primary Language screen displays, type the number in the Choice field that corresponds to y

choice for the primary language and press Enter.e. When the Set Keyboard screen displays, type the number in the Choice field that corresponds to the keyboa

attached to the system and press Enter.e. After you have made all of your selections, verify that the selections are correct. Press Enter to confirm your selections and to

begin the BOS installation. The system automatically reboots after installation is complete.

Step 5. Switch the partition to Normal Mode

1. Switch the partition to Normal Mode, as follows:a. Right-click on the Partition profile to open the menu. Be sure the correct partition profile is highlighted.b. Select Properties.c. Select the Settings tab.d. For the Boot Mode, select Normal.e. Select OK to close the Properties menu.f. Right-click on the partition to open the menu.g. Select Restart Partition.h. Select Immediate for the Restart Options.i. Confirm that you want to restart the partition.j. When the partition has restarted, right-click on the partition to open the menu.k. Select Open terminal window to open a virtual terminal (vterm) window.

Step 6. Complete the BOS installation

1. Complete the BOS installation, as follows:


20/27



a. Type vt100 as the terminal type.

Set Terminal Type

The terminal is not properly initialized. Please enter aterminal type and press Enter. Some terminal types arenot supported in non-English languages.

Ibm3101 tvi912 vt330Ibm3151 tvi920 vt340Ibm3161 tvi925 wyse30

Ibm3162 tvi950 wyse50Ibm3163 vs100 wyse60Ibm3164 vt100 wyse100Ibmpc vt320 wyse350lft sun

+---------------------------Messages----------| If the next screen is unreadable, press

88 Help ? | Break (Ctrl-c) to return to this screen.99 Exit |

|

>>> Choice []: vt100

b. In the License Agreement menu, select Accept License Agreements.c. Select Yes to ACCEPT Installed License Agreements.d. Press F10 or Esc+0 to exit the License Agreement menu.e. In the Installation Assistant main menu, select Set Date and Time.

Installation Assistant

Move cursor to desired item and press Enter.

Set Date and TimeSet root PasswordConfigure Network CommunicationsInstall Software ApplicationsUsing SMIT (information only)

F1=Help F2=Refresh F3=Cancel F8=ImageF9=Shell F10=Exit Enter=Do

f. Set the correct date, time, and time zone. Press the F3 or Esc+3 key to return to the Installation Assistant main menu.g. Select Set Root Password. Set a root password for the partition.h. Select Configure Network Communications. Select TCP/IP Startup. Select from the Available Network Interfaces and pre

Enter. Enter the appropriate network information in the Minimum Configuration and Startup menu and press Enter. Use theF3 or Esc+3 key to return to the Installation Assistant main menu.

i. Exit the Installation Assistant by typing F10 or Esc+0.j. The vterm window displays a login prompt.

At this point, the installation is complete.

Install AIX on a partition without an HMC using the CD-ROM device

In this procedure, you will use the system's built-in CD-ROM device to perform a new and complete AIX BOS installation on the standalonesystem.

Step 1. Prepare your system

There must be adequate disk space and memory available. AIX 5L Version 5.3 requires 128MB of memory and 2.2GB of physical disspace.Make sure your hardware installation is complete, including all external devices.


21/27



If your system needs to communicate with other systems and access their resources, make sure you have the information in the followiworksheet before proceeding with installation:

Network attribute Value

Network interface For example: en0, et0

Host name

IP address

Network mask

Nameserver

Domain name

Gateway


1. Insert the AIX Volume 1 CD into the CD-ROM device.2. Make sure all external devices attached to the system, such as CD-ROM drives, tape drives, DVD drives, and terminals, are turned on

Only the CD-ROM drive from which you will install AIX should contain the installation media.3. Power on the system.4. When the system beeps twice, press F5 on the keyboard or 5 on an ASCII terminal. If you have a graphics display, you will see the

keyboard icon on the screen when the beeps occur. If you have an ASCII terminal (also called a tty terminal), you will see the wordkeyboard when the beeps occur.

5. Select the system console by pressing F1 or 1 on an ASCII terminal and press Enter.6. Select the English language for the BOS installation menus by typing a 1 in the Choice field. Press Enter to open the Welcome to

BOS Installation and Maintenance screen.7. Type 2 to select 2 Change/Show Installation Settings and Install in the Choice field and press Enter.







>>> Choice [1]: 2

Step 3. Set and verify BOS installation settings

1. In the Installation and Settings screen, verify the installation settings are correct by checking the method of installation (new andcomplete overwrite), the disk or disks you want to install, the primary language environment settings, and the advanced options.

2. To change the system settings, which includes the method of installation and disk where you want to install, type 1 in the Choice fieldand press Enter.

Installation and Settings

Either type 0 and press Enter to install with current settings, ortype the number of the setting you want to change andpress Enter.

1 System Settings:Method of Installation............New and Complete OverwriteDisk Where You Want to Install....hdisk0

>>> Choice [0]: 1

3. Type 1 for New and Complete Overwrite in the Choice field and press Enter. The Change Disk(s) Where You Want to Install


22/27



screen now displays.

Change Disk(s) Where You Want to Install

Type one or more numbers for the disk(s) to be used for installationand press Enter. To cancel a choice, type the correspondingnumber and Press Enter. At least one bootable disk must beselected. The current choice is indicated by >>>.

Name Location Code Size(MB) VG Status Bootable

1 hdisk0 04-B0-00-2,0 4296 none Yes2 hdisk1 04-B0-00-5,0 4296 none Yes3 hdisk2 04-B0-00-6,0 12288 none Yes

>>> 0 Continue with choices indicated above

66 Disks not known to Base Operating System Installation77 Display More Disk Information88 Help ?99 Previous Menu

>>> Choice [0]:

4. In the Change Disk(s) Where You Want to Install screen:a. Select hdisk0 by typing a 1 in the Choice field and press Enter. The disk will now be selected as indicated by >>>. To unselect

the destination disk, type the number again and press Enter.b. To finish selecting disks, type a 0 in the Choice field and press Enter. The Installation and Settings screen displays with theselected disks listed under System Settings.

5. Change the Primary Language Environment Settings to English (United States). Use the following steps to change the CulturalConvention, Language, and Keyboard to English.

a. Type 2 in the Choice field on the Installation and Settings screen to select the Primary Language Environment Settingsoption.

b. Type the number corresponding to English (United States) as the Cultural Convention in the Choice field and press Enter.c. Select the appropriate keyboard and language options.

6. Verify that the selections are correct in the Overwrite Installation Summary screen, as follows:

Overwrite Installation Summary

Disks: hdisk0Cultural Convention: en_US

Language: en_USKeyboard: en_US64 Bit Kernel Enabled: NoJFS2 File Systems Created: NoDesktop: CDEEnable System Backups to install any system: Yes

Optional Software being installed:

>>> 1 Continue with Install88 Help ?99 Previous Menu

>>> Choice [1]:

7. Press Enter to begin the BOS installation. The system automatically reboots after installation is complete.

Step 4. Configure the system after installation

1. After a new and complete overwrite installation, the Configuration Assistant opens on systems with a graphics display. On systems wan ASCII display, the Installation Assistant opens.

2. Select the Accept Licenses option to accept the electronic licenses for the operating system.3. Set the date and time, set the password for the administrator (root user), and configure network communications (TCP/IP). Use any ot

options at this time. You can return to the Configuration Assistant or the Installation Assistant by typing configassist or smitty assistthe command line.

4. Select Exit the Configuration Assistant and select Next. Or, press F10 or ESC+0 to exit the Installation Assistant.


23/27



5. If you are in the Configuration Assistant, select Finish now. Do not start the Configuration Assistant when restarting AIX and selectFinish.

At this point, the BOS installation is complete and the initial configuration of the system is complete.

Step 5. Manage your system

When the installation is complete and the system has rebooted, the vterm window displays a login prompt.

Conclusion

You can use a number of other ways to configure a system, depending on the level of sophistication desired. Should you want to explore othepossibilities or require other choices, the Resources section references many articles and Web links that provide you with a lot of usefulinformation.

Resources

Learn about:IBM softwareIBM eServer pSeries and AIX Information CenterIBM eServer Hardware Information Center

Read the following:AIX 5L Version 5.3 Installation Guide and ReferenceAIX application availability guideIBM eServer pSeries Logical Partitioning: Installation and ConfigurationStep-by-step Virtualization configuration on an IBM eServer p5 server, Part 1: Configure VIO ServerStep-by-step Virtualization configuration on an IBM eServer p5 server, Part 2: Configure client partitionsStep-by-step Virtualization configuration on an IBM eServer p5 server, Part 3: Configure virtual devicesPOWER5 virtualization: How to set up the IBM Virtual I/O Server (developerworks, June 2005)

About the author

Shiv Dutta is a technical consultant in the IBM Systems and Technology Group where he assists independent software vendors with the

enablement of their applications on pSeries servers. Shiv was one of the co-authors of AIX 5L Differences Guide Version 5.3 Edition Redboand has considerable experience as a software developer, system administrator, and an instructor. He provides AIX support in the areas ofsystem administration, problem determination, performance tuning, and sizing guides. Shiv has worked with AIX from its inception. He holdPh.D. in Physics from Ohio University and can be reached at [email protected].

Close [x]

developerWorks: Sign in

If you don't have an IBM ID and password, register here.

IBM ID:

Forgot your IBM ID?

Password:

Forgot your password?Change your password

After sign in: Stay on the current page

Keep me signed in.


24/27



By clicking Submit, you agree to the developerWorks terms of use.

Submit Cancel

The first time you sign into developerWorks, a profile is created for you. This profile includes the first name, last name, and display name yoidentified when you registered with developerWorks. Select information in your developerWorks profile is displayed to the public, butyou may edit the information at any time. Your first name, last name (unless you choose to hide them), and display name will accompanythe content that you post.

All information submitted is secure.

Close [x]

Choose your display name

The first time you sign in to developerWorks, a profile is created for you, so you need to choose a display name. Your display nameaccompanies the content you post on developerWorks.

Please choose a display name between 3-31 characters. Your display name must be unique in the developerWorks community and shouldnot be your email address for privacy reasons.

Display name: (Must be between 3 31 characters.)

By clicking Submit, you agree to the developerWorks terms of use.

Submit Cancel

All information submitted is secure.

Average rating (72 votes)

1 star 1 star

2 stars 2 stars3 stars 3 stars

4 stars 4 stars

5 stars 5 stars

Submit

Add comment:

Sign in or register to leave a comment.

Note: HTML elements are not supported within comments.

Notify me when a comment is added1000 characters left

Post


25/27



Print this page Share this page Follow developerWorks

Technical topics

AIX and UNIX

IBM i

Information

Management

Lotus

Rational

Tivoli

WebSphere

Cloud computing

Industries

Integrated Service

Management

Java technology

Linux

Open source

SOA and web services

Web development

XML

More...

Evaluation software

By IBM product

By evaluation method

By industry

Events

Briefings

Webcasts

Find events

Community

Forums

Groups

Blogs

Wikis

Terms of use

Report abuse

IBM Champion

program

More...

About developerWorks

Site help and feedback

Contacts

Article submissions

Related resources

Students and faculty

Business Partners

IBM

Solutions

Software

Software services

Support

Product information

Redbooks

Privacy

Accessibility

Total comments (1)

excellent

Posted by goutham reddy on 18 February 2010

Report abuse


26/27




27/27


Documents

How to Install AIX 5L