Upload
vandiep
View
231
Download
1
Embed Size (px)
Citation preview
page 1page 1
Hilti MI industrial pipe support systemTechnical documentation
Hilti MI industrial pipe support system
page 2
Hilti MI industrial pipe support system
page 3
Technical data
MI-90 MI-120Material thickness s [mm] 3.5 4.0Cross-sectional area A [mm2] 1002.6 1375.7Weight of girder [kg /m] 9.43 12.60
MaterialElastic limit (yield strength) fy,k [N/mm2] 235.0 235.0Permissible tensile stress* σZul [N/mm2] 152.6 152.6Modulus of elasticity [N/mm2] 210000 210000Shear modulus [N/mm2] 81000 81000
SurfaceHot-dip galvanized 70 µm ● ●
Cross-section values y-axisAxis of gravity ey [mm] 45.0 60.0Moment of inertia ly [cm4] 115.34 265.78Section modulus Wy [cm3] 25.63 44.30Radius of gyration iy [cm] 3.39 4.40
Cross-section values x-axisAxis of gravity ez [mm] 45.00 45.00Moment of inertia lz [cm4] 115.34 173.58Section modulus Wz [cm3] 25.63 38.57Radius of gyration iz [cm] 3.39 3.55
Torsion dataTorsional moment of inertia Σ lt [cm4] 155.56 297.02Torsional section modulus Wt = 2* ABredt * [cm3] 45.25 71.63
Technical data /mean valuesincluding torsion
90
50
2590 s = 3.5
120
90 s = 4
50
25
* The permissible stress is calculated from σD / γG/Q with γ = 1,4. σD results from higher yield strength due to cold forming in accordance with DAST-RILI016, issued 1992:σD = fyk / γM mit γM = 1,1
Hilti MI industrial pipe support system
page 4
Single-span subject to bending in one axisF1 when f=L/200, F2 when f=L/300, F when σzul including the framing section’s own weight
MI-90, one single load
Length of F [kN] f [mm] F1 [kN] f [mm] F2 [kN] f [mm]span [mm] ≤ σzul ≤ L/200 ≤ L/300
250 58.75 < 0.1 – – – –500 30.75 0.3 – – – –750 20.67 0.8 – – – –
1000 15.54 1.3 – – – –1250 12.43 2.1 – – – –1500 10.34 3.0 – – – –1750 8.85 4.1 – – – –2000 7.72 5.4 – – – –2250 6.85 6.8 – – – –2500 6.14 8.4 – – 6.06 8.32750 5.56 10.2 – – 4.97 9.23000 5.08 12.2 – – 4.14 10.03250 4.67 14.3 – – 3.49 10.83500 4.31 16.6 – – 2.97 11.73750 4.00 19.1 3.92 18.8 2.55 12.54000 3.73 21.8 3.41 20.0 2.20 13.34250 3.50 24.6 2.98 21.3 1.91 14.24500 3.30 27.6 2.62 22.5 1.66 15.04750 3.10 30.8 2.31 23.8 1.45 15.85000 2.90 34.2 2.05 25.0 1.27 16.75250 2.70 37.8 1.82 26.3 1.11 17.55500 2.60 41.6 1.61 27.5 0.97 18.35750 2.50 45.5 1.44 28.8 0.85 19.26000 2.30 49.7 1.28 30.0 0.74 20.0
MI-120, one single load
Length of F [kN] f [mm] F1 [kN] f [mm] F2 [kN] f [mm]span [mm] ≤ σzul ≤ L/200 ≤ L/300
250 101.32 < 0.1 – – – –500 53.13 0.2 – – – –750 35.73 0.6 – – – –
1000 26.86 1.0 – – – –1250 21.50 1.6 – – – –1500 17.90 2.3 – – – –1750 15.32 3.1 – – – –2000 13.38 4.0 – – – –2250 11.87 5.1 – – – –2500 10.66 6.3 – – – –2750 9.66 7.7 – – – –3000 8.83 9.1 – – – –3250 8.12 10.7 – – – –3500 7.51 12.4 – – 7.03 11.73750 6.98 14.3 – – 6.07 12.54000 6.52 16.3 – – 5.28 13.34250 6.10 18.4 – – 4.62 14.24500 5.74 20.7 – – 4.07 15.04750 5.41 23.1 – – 3.60 15.85000 5.11 25.6 4.98 25.0 3.20 16.75250 4.80 28.2 4.47 26.3 2.85 17.55500 4.60 31.0 4.01 27.5 2.54 18.35750 4.50 34.0 3.62 28.8 2.27 19.26000 4.10 37.1 3.27 30.0 2.03 20.0
90
50
2590 s = 3.5
120
90 s = 4
50
25
L/2 L/2
L
F
L/2 L/2
L
F
-5.00
0.00
5.00
10.00
15.00
20.00
25.00
30.00
35.00
40.00
45.00
50.00
0 500 1000 1500 2000 2500 3000
MI-90MI-120
MQ-41 D/F*MQ-21 D/F*
MQ-41/F*MQ-52-72 D/F*
L
F[kN]Selection of framing section for single span with max. load when f < L/200Single central load incl. framing section’s own weight
Load
F (k
N)
*Technical data for the MQ System can be found in the Installations Systems main catalogue.
Length of span (mm)
Hilti MI industrial pipe support system
page 5
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 9.70 1.70 12.00Fy + Fx + Fz 9.70 1.70 12.00* Force permissible in only one direction ( // = or )Note: Not to be used for cantilevers. Section always requires support at both ends.
MI connector on MI girder (recommended loads1))
MIC-90-U or MIC-120-U on MI-90
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 10.30 1.70 13.70Fy + Fx + Fz 10.30 1.70 13.70* Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Section always requires support at both ends.
MIC-90-U or MIC-120-U on MI-120MI-90
Fy
Fz
Fx
Fy
Fz
Fx
MI-90 or MI-120
Each with single screw (84 Nm)
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 13,20 8,26 18,60Fy + Fx + Fz 13,20 3,10 18,60* Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-90-L auf MI-90 oder MI-120
1) Calculation of rated values: Fd = Frec.�1,52) Our technical advisory service would be pleased to assist with design and calculation.
2 screws crosswise(84 Nm)
Single screw (84 Nm)
Single screw (84 Nm)
M12
M12 x 85
30Fy
Fx
Fz
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fz 1.50 - 1.50Fy + Fx + Fz 0.78 5.80 0.78All loads apply to 1 beam clamp. Recommended shear loads apply to galvanized steel on galvanized steel.Clamps must always be used in pairs.Tightening torque MD: 69 Nm
MI beam clamps (recommended loads1))
MI-GC-M12
Hilti MI industrial pipe support system
page 6
155150
60 x 13
12
220
140
14
MI-120
Fy
Fz
Fx
2 x screws crosswise(84 Nm)
4 x beam clamps (69 Nm)
300B
100
12140
MI-90
60 x 13
Fy
Fz
Fx
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 3.00 9.00 3.00Fy + Fx + Fz 1.56 5.00 1.56* Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Always requires support at both ends.
MI connector on steel beams (recommended loads1))
MIC-S-90-AA
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 14.70 6,00Fy + Fx + Fz 3.11 14.70 3,11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-90-A
155150
60 x 13
MI-90
12
220
140
14
Fy
Fz
Fx
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 10.20 6.00Fy + Fx + Fz 3.11 10.20 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-90-B
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 7.20 6.00Fy + Fx + Fz 3.11 7.20 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-90-C2 x screws crosswise (84 Nm)
4 x beam clamps (69 Nm)
2 x screws crosswise (84 Nm)
2x beam clamps (69 Nm)
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 16.50 6.00Fy + Fx + Fz 3.11 16.50 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-120-A
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 11.30 6.00Fy + Fx + Fz 3.11 11.30 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-120-B
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 8.10 6.00Fy + Fx + Fz 3.11 8.10 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-S-120-C
1) Calculation of rated values: Fd = Frec.�1,52) Our technical advisory service would be pleased to assist with design and calculation.
Hilti MI industrial pipe support system
page 7
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 8.73 8.80 13.20Fy + Fx + Fz 1.60 3.60 1.60*Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
100
MI-90140
200
12
Fy
Fz
Fx
MI connector on concrete (recommended loads1))
MIC-C90-AA3)
156
47 x 17
15
156
230
MI-90
230
140Fy
Fz
Fx
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 28.10 22.00 28.10Fy + Fx + Fz 15.00 12.00 15.00*Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-C90-D4)
156
47 x 17
15
156
230
230
140Fy
Fz
Fx
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 28.10 22.00 28.10Fy + Fx + Fz 15.00 12.00 15.00*Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)
MIC-C120-D4)
MI-90
100
200
8Fy
Fz
Fx
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fz* 5.82 - 13.20Fy + Fz 5.82 - 11.67*Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Always requires support at both ends.
MIC-C90-U3)
1) Calculation of rated values: Fd = Frec. x 1,52) Our technical advisory service would be pleased to assist with design and calculation.3) Fxrec.: Given values apply only to use of HST/HST-R M12 anchors; higher values possible when other
anchors are selected.Fyrec.: Given values apply to all M12 anchorsNote: When loading with Fy, the elongated hole in the base plate in line with the direction of force must be filled with high-strength mortar (e.g. HIT-HY 150).
4) Fxrec., Fyrec., Fzrec.: Given values apply only to use of HST/HST-R M16 anchors; higher values possiblewhen other anchors are selected.
screws crosswise (84 Nm)
screws crosswise (84 Nm)
screws crosswise (84 Nm)
Single screw (84 Nm)
Hilti MI industrial pipe support system
page 8
250
MI-90
Fy
Fz
Fx
250
MI-120
Fy
Fz
Fx
Fy
Fz
Fx
1) Calculation of rated values: Fd = Frec. x 1,5
MI girder extension (recommended loads1))
MIC-90-E
The loading capacity of the extension depends on the moments acting in the Y- and Z-axes.Please consult our technical advisory service.
The loading capacity of the extension depends on the moments acting in the Y- and Z-axes.Please consult our technical advisory service.
MI connector / pedestal connector (recommended loads1))
MIC-T
MIC-120-E
± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fz* - - 20.00Fy + Fx + Fz 3.50 1.00 10.00* Force permissible in only one direction ( // = or )Note: Always to be fitted on both sides.
4 screws crosswise in end ofeach girder (84 Nm)
4 screws crosswise in end ofeach girder (84 Nm)
2 screws (84 Nm)
Hilti MI industrial pipe support system
page 9
197,5
130
80
8120
12.5
100
1552
B
C
D
80
12
12.5
1460 x 13
6
90°
0°
100
100
6
80
8 200
12.5
25 x 14
150
90°
0°
Tension or compression Frec. [kN]2)
Angle 0° 30° 45° 60° 90°24.00 11.80 10.00 9.20 9.70
Note: Always to be fitted in pairs.
MI Multi-angle connectors ( recommended loads 1))
MIC-U-MA (connection to MI girder )
Tension or compression Frec. [kN]2)
Angle 0° 30° 45° 60° 90°16.00 10.00 7.00 6.00 5.00
MIC-SA-MA (connection to steel beam)
Tension or compression Frec. [kN]2)
Angle 0° 30° 45° 60° 90°12.00 10.00 7.00 6.00 5.00
MIC-SB-MA (connection to steel beam)
Tension or compression Frec. [kN]2)
Winkel 0° 30° 45° 60° 90°8.00 8.00 7.00 6.00 5.00
MIC-SC-MA (connection to steel beam)
Tension or compression Frec. [kN]2)3)
Angle 0° 30° 45° 60° 90°7.10 5.00 4.00 4.00 5.30
MIC-CU-MA (connection to concrete)
1) Calculation of rated values: Fd = Frec. � 1,52) Frec. always acts in the longitudinal axis of the girder, irrespective of angle.3) Frec. : Given values apply only to use of HST/HST-R M12 anchors; higher values possible
when other anchors are selected.
2 screws (84 Nm)
4 beam clamps (69 Nm)
Hilti MI industrial pipe support system
page 10
Hilti MI industrial pipe support system
page 11
MI girder
Advantages■ Torsionally rigid girder.■ Pipes may be mounted on all four sides simultaneously.■ Scale marks facilitate installation /cutting to length.■ Crimped-in depression for 100% compatibility with MQ channel
system.
Section height Length Material thickness Weight Ordering designation Item no. Packaged[mm] (m) [mm] (kg/m) in lengths of
90 3 3.5 9.43 �➀MI-90 3m 304798 3m90 6 3.5 9.43 �➀MI-90 6m 304799 6m
120 3 4 12.60 �➁MI-120 3m 304800 3m120 6 4 12.60 �➁MI-120 6m 304801 6m
Technical dataMaterial: S235JRG2 as per DIN 10025 Galvanizing: Hot-dip galvanized 75 µm
90
50
2590 s = 3.5
�
120
90 s = 4
50
25
�
Hilti MI industrial pipe support system
page 12
MI connectors: Crossbeam connectors
Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Only two connecting screws required.■ Keyed hold for optimum transmission of forces and moments.■ Self-locking nuts for vibration-resistant screw connections.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025 Galvanizing: Hot-dip galvanized 55µm
Crossbeam connectors with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI- 90 2.36 � MIC-90-U 304803 4MI-120 2.79 � MIC-120-U 304804 4
Set besteht aus:2x
Crossbeam connectors without connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI- 90 1.78 � MIC- 90-U-AP 305708 4MI-120 2.18 � MIC-120-U-AP 305709 4
NoteAlways to be supported at opposite end.
192
758100
MI-90
220
758100
MI-120
�
�
Items in set
Hilti MI industrial pipe support system
page 13
MI connectors: Cantilever connectors
Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Only four connecting screws required.■ Keyed hold for optimum transmission of forces and moments.■ Self-locking nuts for vibration-resistant screw connections
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025 Galvanizing: Hot-dip galvanized 55 µm
Set besteht aus:4x
2x 2x
2x315
75
8140
Cantilever connector with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI-90 3.95 MIC-90-L 304805 2➀
Cantilever connector without connecting parts
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90 2.80 MIC-90-L-AP 305710 2
NoteDesigned for cantilever applications.May be supported at only one end.
Items in set
Hilti MI industrial pipe support system
page 14
MI connectors: Pedestal connector
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
220
75
8120Pedestal connector with connecting parts
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90/MI-120 2.04 � MIC-T 304807 2
Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Keyed hold for optimum transmission of forces and moments.
�
Set besteht aus:2x
2x
2x2x
Items in set
Hilti MI industrial pipe support system
page 15
MI connectors: Girder extension
Advantages■ Flexurally rigid extension/connection for MI girder.■ Built-in stop prevents the extension sliding right inside the girder.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
Set besteht aus �:
8x8x
250
MI-90
Girder extension with connecting partsFor girder type Weight per ordering designation Item no. Package
set [kg] contents
MI-90 3.57 � MIC-90-E 304809 2MI-120 4.35 � MIC-120-E 304810 2
Set besteht aus �:
8x
4x 4x250
MI-120
�
�
Items in set �
Items in set �
Hilti MI industrial pipe support system
page 16
Steel connectors with connecting partsFor girder type Steel beam width B C D Weight per Ordering designation Item no. Package
[mm] [mm] [mm] set [kg] contents
MI-90 75–165 – – 4.37 � MIC-S90-AA 304811 2MI-90 75–165 200 280 7.14 � MIC-S90-A 304812 2MI-90 165–235 300 350 8.59 � MIC-S90-B 304813 2MI-90 235–300 350 430 10.24 � MIC-S90-C 304814 2MI-120 75–165 200 280 7.54 � MIC-S120-A 304818 2MI-120 165–235 300 350 8.99 � MIC-S120-B 304819 2MI-120 235–300 350 430 10.65 � MIC-S120-C 304820 2
MI steel connectors: Connection to steel beams
Advantages■ For connection to standard steel beams without drilling or welding.■ Suitable for connection to flange or web.■ For use with MI-GC-M12 beam clamp.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
B
155150
60 x 13
MI-90
12
B
CD
220
140
14
155150
60 x 13
12
BC
D
220
140
14
MI-120
�
Set besteht aus:2x
2x
300B
100
12140
MI-90
60 x 13 ��
Note: �Always to be supported at opposite end.
Note: � + �Designed for cantilever applications. May be supported at only one end.
Items in set
Hilti MI industrial pipe support system
page 17
Steel connectors – welded bracket
For girder type Length L Steel beam width B C D Weight per Ordering designation Item no.[mm] [mm] [mm] [mm] set [kg] Recommended working load Fz [kN]
MI-90 500 75–165 200 280 10.18 4.660 2.970 � MIC-S90-A-500 267774MI-90 750 75–165 200 280 12.53 3.920 1.960 � MIC-S90-A-750 267775MI-90 1000 75–165 200 280 14.89 2.900 1.450 � MIC-S90-A-1000 267776MI-90 1500 75–165 200 280 19.61 1.850 0.920 � MIC-S90-A-1500 267777MI-90 2000 75–165 200 280 24.32 1.310 0.650 � MIC-S90-A-2000 267778
MI-90 500 165–235 300 350 11.63 4.660 2.970 � MIC-S90-B-500 267779MI-90 750 165–235 300 350 13.98 3.920 1.960 � MIC-S90-B-750 267780MI-90 1000 165–235 300 350 16.34 2.900 1.450 � MIC-S90-B-1000 267781MI-90 1500 165–235 300 350 21.06 1.850 0.920 � MIC-S90-B-1500 267782MI-90 2000 165–235 300 350 25.77 1.310 0.650 � MIC-S90-B-2000 267783
MI-90 500 235–300 350 430 13.29 4.230 2.110 � MIC-S90-C-500 267784MI-90 750 235–300 350 430 15.64 2.780 1.390 � MIC-S90-C-750 267785MI-90 1000 235–300 350 430 18.00 2.040 1.020 � MIC-S90-C-1000 267786MI-90 1500 235–300 350 430 22.72 1.280 0.640 � MIC-S90-C-1500 267787MI-90 2000 235–300 350 430 27.43 0.880 0.440 � MIC-S90-C-2000 267788
MI-120 500 75–165 200 280 11.76 4.640 3.610 � MIC-S120-A-500 267794MI-120 750 75–165 200 280 14.91 4.640 2.380 � MIC-S120-A-750 267795MI-120 1000 75–165 200 280 18.06 3.510 1.750 � MIC-S120-A-1000 267796MI-120 1500 75–165 200 280 24.36 2.230 1.110 � MIC-S120-A-1500 267797MI-120 2000 75–165 200 280 30.66 1.560 0.780 � MIC-S120-A-2000 267798
MI-120 500 165–235 300 350 13.21 4.640 2.960 � MIC-S120-B-500 267799MI-120 750 165–235 300 350 16.36 3.900 1.950 � MIC-S120-B-750 270459MI-120 1000 165–235 300 350 19.51 2.870 1.430 � MIC-S120-B-1000 270460MI-120 1500 165–235 300 350 25.81 1.810 0.900 � MIC-S120-B-1500 270461MI-120 2000 165–235 300 350 32.11 1.240 0.620 � MIC-S120-B-2000 270462
MI-120 500 235–300 350 430 14.87 4.640 2.320 � MIC-S120-C-500 270463MI-120 750 235–300 350 430 18.02 3.040 1.520 � MIC-S120-C-750 270464MI-120 1000 235–300 350 430 21.17 2.230 1.110 � MIC-S120-C-1000 270465MI-120 1500 235–300 350 430 27.47 1.230 0.690 � MIC-S120-C-1500 270466MI-120 2000 235–300 350 430 33.77 0.810 0.460 � MIC-S120-C-2000 270467
MI steel connectors: Connection to steel beams
Advantages■ For connection to standard steel beams without drilling or welding.■ Suitable for connection to flange or web.■ Lightweight for easy one man installation.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 75 µm
155150
60 x 13
12
BC
D
220
L
14
�
B
Fz1/2 1/2
Fz1/31/3
Fz1/3
155
60 x 13
12
B
D
C
220
L
14
�Note: � + �Designed for cantilever applications. May be supported at only one end.
Calculated by:Suitable Hilti beam clamps MI-GC-M12, Item No. 304894
FZFZ
Hilti MI industrial pipe support system
page 18
Concrete connector with connecting partsFor girder type Weight per Ordering designation Item no Package
set [kg] contents
MI-90 3.51 � MIC-C90-AA 304825 2MI-90 7.32 � MIC-C90-D 304827 2MI-120 7.69 � MIC-C120-D 304829 2
MI concrete connectors: Connection to concrete
Advantages■ Four elongated holes for easy wall mounting.■ Designed for ceiling, wall and floor mounting.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
Set besteht aus:2x
2x
100
140 200
12
MI-90156
47 x 17
15
156
230
MI-90
230
140
156
47 x 17
15
156
230
230
140
� � �
Note: �Always to be supported at opposite end.
Note: � + �Designed for cantilever applications. May be supported at only one end.
Items in set
Hilti MI industrial pipe support system
page 19
Concrete connector – welded bracket
For girder type Length L Weight per Ordering designation Item no.[mm] set [kg] Recommended working load Fz [kN]
MI-90 500 10.60 9.380 4.690 � MIC-C90-D-500 267789MI-90 750 12.95 6.210 3.100 � MIC-C90-D-750 267790MI-90 1000 15.31 4.610 2.300 � MIC-C90-D-1000 267791MI-90 1500 20.03 3.000 1.500 � MIC-C90-D-1500 267792MI-90 2000 24.74 2.160 1.080 � MIC-C90-D-2000 267793
MI-120 500 12.18 10.000 5.320 � MIC-C120-D-500 270468MI-120 750 15.33 7.040 3.520 � MIC-C120-D-750 270469MI-120 1000 18.48 5.230 2.610 � MIC-C120-D-1000 270470MI-120 1500 24.78 3.380 1.690 � MIC-C120-D-1500 270471MI-120 2000 31.08 2.420 1.210 � MIC-C120-D-2000 270472
Note: � + �Designed for cantilever applications. May be supported at only one end.
Anchor Calculated by:Approved Hilti HST(R) M16 anchors; alternative approved Hilti anchors are the Hilt HVZ, HIT-TZ(R) of thesame nominal diameter and same version.
MI concrete connectors: Connection to concrete
Advantages■ Four elongated holes for easy wall mounting.■ Designed for ceiling, wall and floor mounting.■ Lightweight for easy one man installation.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 75 µm
156
47 x 17
15
156
230
230
L
156
47 x 17
15
156
230
230
L
� �
Fz1/2 1/2
Fz1/31/3
Fz1/3
FZFZ
Hilti MI industrial pipe support system
page 20
Concrete wall connector with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI-90 2.29 � MIC-C90-U 304826 2
MI concrete connectors: Connection to concrete walls
Advantages■ Lighter version for structures supported at both ends.■ Elongated holes for easier positioning.■ Simple support for installation between two walls.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
Set besteht aus:1x
1x
100
25 x 14
8150
200
100
MI-90
�
NoteAlways to be supported at opposite end.
Items in set
Hilti MI industrial pipe support system
page 21
MI connectors: Multi-angle connectors
Advantages■ For supports / corner struts at angles between 0° and 180°.■ For connecting directly to standard steel beams or concrete.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
MI angle connectors for girder, with connecting parts
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90/MI-120 2.53 � MIC-U-MA 304806 2
MI angle connectors for steel, with connecting parts
For girder type Steel beam width B C D Weight per Ordering designation Item no. Package[mm] [mm] [mm] set [kg] contents
MI-90/MI-120 75–165 200 280 6.29 � MIC-SA-MA 304815 4MI-90/MI-120 165–235 300 350 7.74 � MIC-SB-MA 304816 2MI-90/MI-120 235–300 350 430 9.40 � MIC-SC-MA 304817 2
MI angle connectors for concrete, with connecting parts
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90/MI-120 2.04 � MIC-CU-MA 304828 4
197,5
130
80
8120
12.5
Set besteht aus:
2x
2x
Set besteht aus:
Set besteht aus:
100
155220
B
C
D
80
12
12.5
1460 x 13
6
�
�
100
100
6
80
8 200
12.5
25 x 14
150
�
Items in set
Items in set
Items in set
�
�
Hilti MI industrial pipe support system
page 22
MI steel / concrete connectorsBase plates for steel / concrete
Advantages■ All steel beam widths from 75–300 mm covered by only 3 plate
sizes.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
�
155
150
60 x 13
12
BC
D
220
14
156
47 x 17
15
156
230
230
�MI base plates for steel /concrete, without connecting partsFor girder type Steel beam width B C D Weight per Ordering Item no. Package
[mm] [mm] [mm] set [kg] designation contents
MI-90/MI-120 75–165 200 280 5.46 � MIB-SA 304821 2MI-90/MI-120 165–235 300 350 6.91 � MIB-SB 304822 2MI-90/MI-120 235–300 350 430 8.57 � MIB-SC 304823 2MI-90/MI-120 For connection to concrete 5.88 � MIB-CD 304830 2
Hilti MI industrial pipe support system
page 23
MI basic connector for welding, without connecting parts
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI- 90 1.44 � MIC-SC90 304824 2MI-120 1.81 � MIC-SC120 304808 2
Flexy pack: Adaptable connectorfor steel or concrete
Advantages■ The girder connection point can be positioned as desired
for special cases.■ Supplied in a primer finish for trouble-free welding.
Can be galvanized later if desired.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Corrosion protection: None (primer coating-basic connector)
72
72
140
101
71
140� �
Flexy pack – connector for welding as desired, without connecting parts
Parts listOrdering designation Item no. Info Position
MIC-SC90 or MIC-SC120 304824 or 304808 Pos.1MIB-SA or MIB-SB 304821/304822 Depending on base material Pos.2MIB-SC or MIB-CD 304823/304830 or size of steel beam
Pos. 2
Pos. 1
Hilti MI industrial pipe support system
page 24
49
15
28,5
400
96
6
177,5 x 13
35 x 13
MI U-bolt clamps with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI-90 1.26 � MIC-UB90 304831 10*MI-90 2.58 � MIC-UB90 L400 304832 2MI-120 1.38 � MIC-UB120 304833 10*MI-90 1.24 � MIC-UB90-M16 304834 6*MI-120 1.36 � MIC-UB120-M16 304835 6*
*numbers of pairs in set
Advantages■ Reliable fastening system for U-bolts.■ Elongated holes for full adjustment of pipe position.■ Keyed hold for optimum transmission of forces.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µmConnecting screws: M12 (connection to MI-girder)
90
90
65 x 13 49
26 x 13,5
96
90
65 x 13 49
26 x 13,596
90
65 x 17 49
26 x 13,5
� � ��
Pipe clamps: U-bolt clamps for uninsulated pipes
Set : besteht aus:
2x
2x 2x
2x2x
Set : besteht aus:
2x
1x
2x 2x 2x
90
90
65 x 17 49
26 x 13,5
�
����Items in set ����
Items in set �
Hilti MI industrial pipe support system
page 25
U-bolts with connecting partsNominal size Pipe outside d1 b2 h Shank d3 e Weight Ordering designation Item no. Package
diameter Da dia. each contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [kg]
25 33.7 38 50 76 10 M10 48 0.13 MI-UB 25-M10 304870 540 48.3 52 50 92 10 M10 62 0.16 MI-UB 40-M10 304871 550 60.3 64 50 109 12 M12 76 0.24 MI-UB 50-M12 304872 565 76.1 82 50 125 12 M12 94 0.27 MI-UB 65-M12 304873 580 88.9 94 50 138 12 M12 106 0.29 MI-UB 80-M12 304874 5
100 114.3 120 60 171 16 M16 136 0.64 MI-UB 100-M16 304875 5125 139.7 148 60 191 16 M16 164 0.72 MI-UB 125-M16 304876 3150 168.3 176 60 217 16 M16 192 0.80 MI-UB 150-M16 304877 3200 219.1 228 70 283 16 M16 244 1.01 MI-UB 200-M16 304878 3250 273.0 282 70 334 16 M16 298 1.19 MI-UB 250-M16 304879 3
Pipe clamps: MI U-bolts for uninsulated pipes
Advantages■ Small contact surface between U-bolt and pipe.■ Minimizes crevice corrosion.■ In compliance with DIN standard for U-bolts.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 45 µmTemperatures: 300 °C
h
b2
d3e
d1
Hilti MI industrial pipe support system
page 26
Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Packagesize diameter Da screw set Fx +Fz –Fz Fy contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kN) (kN) (kN) (kN)
25 33.7 30 6 9 80 85 250 – M10 2.8 0.4 0.8 0.3 0.3 � MI-PS1/1 25-85 304844 225 33.7 30 6 8 82 140 250 – M10 2.4 0.4 0.8 0.3 0.3 � MI-PS1/1 25-140 286957 240 48.3 30 6 9 80 85 250 – M10 2.8 0.5 1.0 0.3 0.3 � MI-PS1/1 40-85 304845 240 48.3 30 6 8 82 140 250 – M10 2.4 0.5 1.0 0.3 0.3 � MI-PS1/1 40-140 286958 250 60.3 40 6 9 80 85 250 – M12 3.2 0.9 1.8 0.6 0.6 � MI-PS1/1 50-85 304846 250 60.3 40 6 8 82 140 250 – M12 2.7 0.9 1.8 0.6 0.6 � MI-PS1/1 50-140 286959 265 76.1 40 6 9 80 85 250 – M12 3.3 1.1 2.1 0.7 0.7 � MI-PS1/1 65-85 304847 265 76.1 40 6 8 82 140 250 – M12 2.8 1.1 2.1 0.7 0.7 � MI-PS1/1 65-140 286960 280 88.9 40 6 9 80 85 250 – M12 3.3 1.2 2.3 0.8 0.8 � MI-PS1/1 80-85 304848 280 88.9 40 6 8 82 140 250 – M12 2.9 1.2 2.3 0.8 0.8 � MI-PS1/1 80-140 286961 2
100 114.3 40 8 9 80 85 250 – M12 3.8 2.5 5.0 1.7 1.7 � MI-PS1/1 100-85 304849 2100 114.3 40 8 8 80 140 250 – M12 3.4 2.5 5.0 1.7 1.7 � MI-PS1/1 100-140 286962 2125 139.7 40 8 9 80 85 250 – M12 4.0 2.9 5.8 1.9 1.9 � MI-PS1/1 125-85 304850 2125 139.7 40 8 8 80 140 250 – M12 3.6 2.9 5.8 1.9 1.9 � MI-PS1/1 125-140 286963 2150 168.3 40 8 9 80 85 250 – M12 4.2 3.2 6.4 2.1 2.1 � MI-PS1/1 150-85 304851 2150 168.3 40 8 8 80 140 250 – M12 3.8 3.2 6.4 2.1 2.1 � MI-PS1/1 150-140 286964 2
25 21.3 30 5 9 80 85 250 200 M10 3.3 0.8 1.5 0.5 0.5 � MI-PS2/1 25-85 304852 225 21.3 30 5 9 80 140 250 180 M10 3.7 0.8 1.5 0.5 0.5 � MI-PS2/1 25-140 286965 240 48.3 30 5 9 80 85 250 200 M10 3.4 1.0 2.0 0.7 0.7 � MI-PS2/1 40-85 304853 240 48.3 30 5 9 80 140 250 180 M10 3.8 1.0 2.0 0.7 0.7 � MI-PS2/1 40-140 286966 250 60.3 40 6 9 80 85 250 190 M12 4.1 1.8 3.5 1.2 1.2 � MI-PS2/1 50-85 304854 250 60.3 40 6 9 80 140 250 180 M12 4.5 1.8 3.5 1.2 1.2 � MI-PS2/1 50-140 286967 265 76.1 40 6 9 80 85 250 190 M12 4.3 2.1 4.2 1.4 1.4 � MI-PS2/1 65-85 304855 265 76.1 40 6 9 80 140 250 180 M12 4.7 2.1 4.2 1.4 1.4 � MI-PS2/1 65-140 286968 280 88.9 40 6 9 80 85 250 190 M12 4.4 2.4 4.7 1.6 1.6 � MI-PS2/1 80-85 304856 280 88.9 40 6 9 80 140 250 180 M12 4.8 2.4 4.7 1.6 1.6 � MI-PS2/1 80-140 286969 2
100 114.3 40 8 9 80 85 250 190 M12 5.3 3.0 6.0 2.0 2.0 � MI-PS2/1 100-85 304857 2100 114.3 40 8 9 80 140 250 180 M12 5.8 3.0 6.0 2.0 2.0 � MI-PS2/1 100-140 286970 2125 139.7 40 8 9 80 85 250 190 M12 5.7 3.5 7.0 2.3 2.3 � MI-PS2/1 125-85 304858 1125 139.7 40 8 9 80 140 250 180 M12 6.1 3.5 7.0 2.3 2.3 � MI-PS2/1 125-140 286971 1150 168.3 40 8 9 80 85 250 190 M12 6.1 4.0 8.0 2.7 2.7 � MI-PS2/1 150-85 304859 1150 168.3 40 8 9 80 140 250 180 M12 6.6 4.0 8.0 2.7 2.7 � MI-PS2/1 150-140 286972 1200 219.1 50 8 9 100 107 250 180 M16 8.5 4.8 9.5 3.2 3.2 � MI-PS2/1 200-107 304860 1200 219.1 50 8 9 100 142 250 180 M16 8.9 4.8 9.5 3.2 3.2 � MI-PS2/1 200-142 286973 1250 273.0 50 8 9 100 107 250 180 M16 9.5 5.3 10.5 3.5 3.5 � MI-PS2/1 250-107 304861 1250 273.0 50 8 9 100 142 250 180 M16 9.9 5.3 10.5 3.5 3.5 � MI-PS2/1 250-142 286974 1300 323.9 50 8 9 100 107 250 180 M16 10.5 5.8 11.5 3.8 3.8 � MI-PS2/1 300-107 304862 1300 323.9 50 8 9 100 142 250 180 M16 10.9 5.8 11.5 3.8 3.8 � MI-PS2/1 300-142 286975 1
* The maximum permissible loads for connecting components must be taken into account when the pipe support is used!
MI pipe clamps: Pipe supports for insulated pipes
Advantages■ With mounting holes for installing light-duty fixed points.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 70 µmTemperatures: Up to 300 °C
8
5
75
L
F
W
s
Da
B
H
13
Fy
Fx
– Fz
+ Fz
L
F
W
sDa
B
L1
H
13
Fy
Fx
– Fz
+ Fz
L
F
W
sDa
B
L1
H
13
Fy
Fx
– Fz
+ Fz
1 ring / 1 rib for DN25-DN150
Low-friction plate
2 rings / 1 rib for DN25-DN300
Sliding support clamps
Heavy-duty version for DN200-DN600
Fixed point
� � �
Hilti MI industrial pipe support system
page 27
Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Packagesize diameter Da screw set Fx +Fz –Fz Fy contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kN) (kN) (kN) (kN)
200 219.1 50 8 8 175 107 290 260 M16 12.4 – 12.0 4.0 4.0 � MI-PS2/2 200-107 304863 1200 219.1 50 8 8 175 142 290 260 M16 15.5 – 12.0 4.0 4.0 � MI-PS2/2 200-142 286976 1250 273.0 50 8 8 175 107 290 260 M16 13.2 – 15.0 5.0 5.0 � MI-PS2/2 250-107 304864 1250 273.0 50 8 8 175 142 290 260 M16 16.3 – 15.0 5.0 5.0 � MI-PS2/2 250-142 286977 1300 323.9 50 8 8 175 107 290 260 M16 14.0 – 16.0 5.3 5.3 � MI-PS2/2 300-107 304865 1300 323.9 50 8 8 175 142 290 260 M16 17.0 – 16.0 5.3 5.3 � MI-PS2/2 300-142 286978 1350 355.6 60 8 10 175 142 290 250 M16 19.2 – 17.8 5.9 5.9 � MI-PS2/2 350-142 304866 1350 355.6 60 8 10 175 192 290 250 M16 21.4 – 17.8 5.9 5.9 � MI-PS2/2 350-192 286979 1400 406.4 60 8 10 250 142 290 250 M16 24.9 – 18.7 6.0 6.0 � MI-PS2/2 400-142 304867 1400 406.4 60 8 10 250 192 290 250 M16 27.9 – 18.7 6.0 6.0 � MI-PS2/2 400-192 286980 1500 508.0 70 10 10 250 142 290 240 M20 33.5 – 21.3 6.0 6.0 � MI-PS2/2 500-142 304868 1500 508.0 70 10 10 250 192 290 240 M20 36.5 – 21.3 6.0 6.0 � MI-PS2/2 500-192 286981 1600 610.0 70 10 10 250 142 290 240 M20 36.8 – 28.0 6.0 6.0 � MI-PS2/2 600-142 304869 1600 610.0 70 10 10 250 192 290 240 M20 38.8 – 28.0 6.0 6.0 � MI-PS2/2 600-192 286982 1
* The maximum permissible loads for connecting components must be taken into account when the pipe support is used!
MI pipe clamps: Pipe supports for insulated pipes
Advantages■ With mounting holes for installing light-duty fixed points.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 70 µmTemperatures: Up to 300 °C
8
5
75
L
F
W
s
Da
B
H
13
Fy
Fx
– Fz
+ Fz
L
F
W
sDa
B
L1
H
13
Fy
Fx
– Fz
+ Fz
L
F
W
sDa
B
L1
H
13
Fy
Fx
– Fz
+ Fz
1 ring / 1 rib for DN25-DN150
Low-friction plate
2 rings / 1 rib for DN25-DN300
Sliding support clamps
Heavy-duty version for DN200-DN600
Fixed point
� � �
Hilti MI industrial pipe support system
page 28
Advantages■ Pipe ring support free to move in one direction.■ Fully adjustable.■ Spacer plates permit use of pipe supports with
base plates of greater thickness.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 45 µm
12
90
45
18130
102
M12
12
120
45
18130
102
M12
� �
4
102
30130
13
16
6
102
30
18
130
13� �
�
MI pipe clamps: MI sliding support clamping system for insulated pipes
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90 1.80 � MIC-PS90 304838 4*MI-120 1.88 � MIC-PS120 304839 4*MI-90/MI-120 0.22 � MIC-PSP-4MM 283593 10*MI-90/MI-120 0.34 � MIC-PSP-6MM 283594 10**Number of pairs in package
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90/MI-120 0.1 � MIC-PG 304842 108
5
75
MI clamping system for sliding support, with connecting parts
MI low-friction system for sliding support
Technical data for low-friction systemMaterial: PE-UH MWFriction value: µ = 0,15Temperature resistance: –273,15 °C to +90 °C
Hilti MI industrial pipe support system
page 29
126
M12
102
156
M12
102� �
Advantages■ Quickly and easily installed pipe support system for light-duty fixed
points.
MI clamping system for fixed points, with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI-90 0.60 � MIA-B090-M12 304840 8*MI-120 0.68 � MIA-B0120-M12 304841 8*
*Number of pairs in package
MI pipe clamps: MI rigid support clamping system,with connecting parts
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 45 µm
Hilti MI industrial pipe support system
page 30
For girder type Weight per Suitable pipe Ordering designation Item no. Packageset [kg] diameter [mm] contents
MI-90/MI-120 5.50 219 ÷ 406 MI-DPR 304880 1
MI pipe clamps:Twin roller support
Advantages■ Dimensions suitable for fastening to MI-girder with MIC-PA90
or MIC-PA120.
Technical data:Body material: S235 JRG2 as per DIN EN 10 025Roller material: S355 JO as per DIN EN 10 025Axle material: Stainless steel (1.4541)Rated load capacity: 15 kNCoefficient of friction: 0.035
2x 2x
2x2x
Set besteht aus:
86
130
8
190
225
E
DA
Items in set
90
10210
M12
150
Adaptor plate with connecting partsFor girder type Weight per Ordering designation Item no. Package
set [kg] contents
MI-90 3.38 � MIC-PA90 304836 2MI-120 3.46 � MIC-PA120 304837 2
Advantages■ The adaptor plate takes the place of the steel beam flange and thus
permits the use of conventional clamping systems for pipe supports.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
�
120
10210
150
M12
�
MI pipe clamps: Adaptor plate forpipe support clamping system,incl. connecting parts
DA = Outside-diameter pipe
E = 0.532 x DA + 54
Hilti MI industrial pipe support system
page 31
MI pipe clamps: Plate for weld-on tabs
Advantages■ Easy installation of standard weld-on tabs, e.g. for spring hangers.
Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: U-bolt galvanized 45µm,
plate with primer finish
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90 1.01 � MIC-SPH-90 304843 4MI-120 1.10 � MIC-SPH-120 283592 4
90
12
M12
60
130
120
12
M12
60
130
� �
��
Hilti MI industrial pipe support system
page 32
For girder type Weight per Ordering designation Item no. Packegeset [kg] contents
MI-90 0,16 � MIA-EH90 304887 10MI-120 0,19 � MIA-EH120 304888 10MI-90 0,10 � MIA-OH90 304889 10MI-120 0,13 � MIA-OH120 304890 10MI-90, MI-120 0,28 � MIA-EH-P 304891 10MI-90, MI-120 0,02 � M12-F hex.collar nut 283589 50MI-90, MI-120 0,06 � MIA-TP 305707 20MI-90, MI-120 0,10 Hex.head screw M12�120-F/8.8 283595 40MI-90, MI-120 0,11 Hex.head screw M12�130-F/8.8 283596 40MI-90, MI-120 0,005 A 13-F washer 304771 100
MI accessories: Individual connecting parts
Advantages■ Parts designed for easy assembly with one hand (shaped to prevent
rotation).■ “Easy hand” plate (5) for easy single-handed adjustment of the con-
nection.
Technical dataMaterial: EN-GJMW-400-5 as per DIN EN 1562Screws: 8.8 grade Nuts: 8 grade DIN 1661, self lockingGalvanizing: 45 µm
120
M12
36,6
36,6
150
M12
36,6
36,6
95
M12 127
M12
72
50
12M12
26
12,2 x 12,2
36,6 36,6
7
�
�
�
�
�
�
�
Examples of applications (cantilever)
Assembly procedure
1.
2.
2-3x
1.2.
1 2
3 4
Hilti MI industrial pipe support system
page 33
MI accessories: End caps
Advantages■ Ends of girder closed securely.■ With built-in opening to permit drainage of liquids.
Technical dataMaterial: Moplen EP 240HTemperature resistance: –30° to +90° C
For girder type Weight Ordering designation Item no. Package [kg] contents
MI-90 0.03 � MIA-EC-90 304892 25MI-120 0.04 � MIC-EC-120 304893 25
� �
18.5
96
96
18.5
126
96
Hilti MI industrial pipe support system
page 34
For girder type Weight per Ordering designation Item no. Packageset [kg] contents
MI-90/MI-120 0.27 � MI-GC-M12 304894 16MI-90/MI-120 0.03 � MI-GCD-6MM 283590 16MI-90/MI-120 0.07 � MI-GCD-12MM 283591 16
MI accessories: Beam clamps for various flange thicknesses
Advantages■ For steel beams with a flange thickness of 3 -12 mm and angle of
up to 15°.■ Spacers for use with flange thicknesses greater than 12 mm.
Note■ The flat nose must be positioned against the steel beam and the
round nose on the connecting part or spacer.
Technical dataMaterial: EN-GJMW-400-5 as per DIN EN 1562Galvanizing: Hot-dip galvanized 55 µmScrews: 8.8 grade
M12
M12 x 85
30
12
3830
6
3830
�
� �
Hilti MI industrial pipe support system
page 35
Hilti MI industrial pipe support system
page 36
MI / MQ connectors with connecting partsFor channel Weight per Ordering designation Item no. Package
set [kg] contents
MQ-41, MQ-21D 0.36 � MIC-MI/MQ-X 304881 16all MQ single channels 0.05 � MIC-MI/MQ-M8 304882 5
MI / MQ connector
Advantages■ Direct connection to components of the Hilti MQ system.■ Keyed hold for optimum transmission of forces and moments.
Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm
250
41
47
4
61 x 11
5
12
M8x16SW13
�
�
�
Set besteht aus:
2x
4x
2x
Set besteht aus:
Items in set
Items in set
Assembly procedure
2.
1.M8x16
1 2
Description Size Ordering designation Item no. Package contents
Magnetic wrench SW 13 � MQZ-SVS 369693 1
200 mm
SW 13mit MagneteinsatzSW 13with magnetic insert
Hilti MI industrial pipe support system
page 37
MQV-UB U-bolt pipe clamp for MQ system
Advantages■ Easy installation of U-bolts.■ Fastened with wing nuts or hex. nuts.
Technical dataMaterial: S235JR as per DIN EN 10025Galvanizing: hot-dip galvanized, approx. 55 µm
47530
37
1113
MQV-PS pipe support for MQ system
55
37
12
25
94
4
11
Advantages■ Easy installation as guide-type pipe support.■ Fastened with wing nuts or hex. nuts.
Technical dataMaterial: S235JR as per DIN EN 10025Galvanizing: hot-dip galvanized, approx. 55 µm
MQP-U universal joint
For D1 D2 Weight each Ordering Item no. Package[mm] [mm] [g] designation contents
M12 12,5 12,5 390 MQP-U M12 284248 10M16 16,5 16,5 390 MQP-U M16 284249 10
Item no. Max. recommended load Tightening torque MD[kN] [Nm]
MQP-U M12 14 20MQP-U M16 14 20
MQP-45°-F base material connectorFor channel Weight each Ordering designation Item no. Package
[g] contents
MQ-21-F, MQ-41-F 350 MQP-45°-F 304164 1105
4241
14
45°
For channel Weight per Ordering designation Item no. Packageset [g] contents
MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-UB-M12 304884 5** Number of pairs in package
For channel Weight each Ordering designation Item no. Package[g] contents
MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-PS 304886 1** Number of pairs in package
Hilti MI industrial pipe support system
page 38
Example of applicationOpposite cantilever arms at same or similar height
Parts listQuantity Ordering designation Item no. Info Position
2 MIC-90-L-AP 305710 Cantilever connectors Pos. 12 MIC-EH-90 304887 Pos. 22 MIA-TP 305707 Pos. 34 MIA-OH90 304889 Pos. 46 M12-F hex. collar nut 283589 Self-locking nuts Pos. 5
Pos. 1
Pos. 3 Pos. 5
Pos. 4
Pos. 2
Example of applicationGirder connection to steel beam
Pos. 1
Pos. 2
Pos. 3Pos. 4
Beam height up to about 320 mm.
Parts list (beam height up to 320 mm)Quantity Ordering designation Item no. Info Position
1 MIC-S*(A/B/C) 304812/304813/304814 To suit beam size Pos. 11 MIB-S* 304821/ 304822/ 304823 Size as (1) Pos. 24 AM 12-F 304774 M12-F threaded rod Pos. 38 M12-F hex. collar nut 283589 Self-locking nuts Pos. 4*Plate size to be selected to suit width between flanges
Advantages■ Girder can be connected to steel beam without welding.
Hilti MI industrial pipe support system
page 39
Pos. 1
Pos. 3
Pos. 5
Pos. 2
Pos. 4
Beam height greater than 320 mm.Further connections using MIC-90-L cantilever connector.
Parts list (beam height greater than 320 mm)Quantity Ordering designation Item no. Info Position
2 MI-90 304799 Length to suit beam size Pos.18 MIC-UB90-M12 304831 Pos.24 Hex.head screw M12�120F/ 8.8 283595 Pos.3
12 M12-F hex. collar nut 283589 Self-locking nuts Pos.44 AM 12-F 304774 M12-F threaded rod Pos.5
Parts listQuantity Ordering designation Item no. Info Position
1 MIB-SA 304821 Pos. 14 MIA-EH-P 304891 Pos. 24 A13-F 304771 Pos. 34 M12�130F/8.8 hex screw 283596 Pos. 44 M12 hex. collar nut 283589 Self-locking nut Pos. 5
Example of applicationCross connection between MI girder
Pos. 1 Pos. 4
Pos. 3
Pos. 5
Pos. 2
Pos. 5
Advantages■ Keyed hold for optimum transmission of forces and moments.
Hilti Corporation | 9494 Schaan | Liechtenstein | P +423-234 2111 | F +423-234 2965
Hilti. Outperform. Outlast.
Hilt
i = r
egis
tere
d t
rad
emar
k o
f H
ilti C
orp
., S
chaa
n |
W 2
915
090
6 5
-en
| 1
P
rint
ed in
Lie
chte
nste
in
| ©
200
6 |
Rig
ht o
f te
chni
cal a
nd p
rog
ram
me
chan
ges
res
erve
d
S. E
. & O
.