Embed Size (px)
Citation preview
H.264 Hardware Codec
8/16 Ch Network Digital
Video Recorder
User’s Manual
VERSION 2.0 English
2
INSTRUCTION MANUAL To obtain the best performance and ensure device function correctly, please read this instruction manual carefully and completely. FCC Compliance
USER-INSTALLER CAUTION: YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES. NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
3
WARNINGS, CAUTIONS & COPYRIGHT
WARINGS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS. CAUTION
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of insinuated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral rhombus is intended to alert the user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the product.
USERS OF THE SYSTEM ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL, STATE, AND LOCAL LAWS AND STATUTES COIPCERNING THE MONITORING AND RECORDING OF VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS SYSTEM IN VIOLATION OF CURRENT LAWS AND STATUTES.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR RESPECTIVE COMPANIES.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION
4
TABLE OF CONTENTS 1 INTRODUCTION...................................................................................................................... 6
1.1 FEATURE ......................................................................................................................6 1.2 SPECIFICATION ..........................................................................................................6
2 HARDWARE OVERVIEW...................................................................................................... 8 2.1 FRONT PANEL .............................................................................................................8 2.2 BACK PANEL..............................................................................................................10 2.3 ADVANCED ZOOM, PTZ & COPY KEY CONTROL........................................... 11 2.4 CAMERA & MONITOR LOOPING.........................................................................12 2.5 EXTERAL ALARM.....................................................................................................12 2.6 IR REMOTE CONTROL ...........................................................................................14 2.7 PTZ (PAN, TILT AND ZOOM) CAMERA ...............................................................15
3 SYSTEM SETUP ..................................................................................................................... 16 3.1 MENU SETUP INTERFACE(GUI)...........................................................................16 3.2 LIVE VIEWING AND POP-UP MENU....................................................................18 3.3 CAMERA SETUP ........................................................................................................21 3.4 MOTION SETUP.........................................................................................................23 3.5 RECORD SETUP ........................................................................................................24 3.6 ALARM SETUP...........................................................................................................26 3.7 HARD DISK MANAGEMENT SETUP ....................................................................27 3.8 NETWORK SETUP ....................................................................................................29 3.9 BACKUP SETUP .........................................................................................................30 3.10 SYSTEM SETUP .........................................................................................................33
4 DVR PLAYBACK .................................................................................................................... 37 4.1 TIME SEARCH ...........................................................................................................38 4.2 EVENT SEARCH ........................................................................................................39
5 BACKUP PLAYBACK ........................................................................................................... 40 5.1 MAIN SCREEN SETTING ........................................................................................40 5.2 CD/DVD BACKUP PLAYBACK ...............................................................................43 5.3 USB & LOCAL BACKUP FILE PLAYBACK .........................................................44 5.4 BACKUP FILE TO AVI ..............................................................................................46
6 NETWORK VIEWING & PLAYBACK ............................................................................... 47 6.1 IP ADDRESS SETUP ON PC SITE...........................................................................47 6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP..............................48 6.3 LOGIN ..........................................................................................................................51 6.4 REMOTE CONTROL.................................................................................................52 6.5 CONFIGURE ...............................................................................................................56
7. 3GPP APPLICATION & SETTING ..................................................................................... 65 APPENDIX A: RECORDING TIME LAPSE (HOURS)............................................................. 67
5
CIF..................................................................................................................................................... 67 FIELD ............................................................................................................................................... 68 APPENDIX B: HDD COMPATIBLE TABLE .............................................................................. 69
6
1 INTRODUCTION
1.1 FEATURE H.264 Hardware Codec Video Compression Recording Image Per Second (IPS): 240 IPS for 8/16 channels Display Image Per Second (IPS): 480 IPS for 8/16 channels IPS and Recording Quality Adjustable (by channel) User Friendly Operation (Front Panel Button/ Remote Controller/ Mouse) Support CMS (Central Management System) and 3GPP. Audio Backup / Audio Streaming. Support Day/Time and Event search function via Ethernet remote control mode or Local
site Support PPPoE/ Static/ DHCP IP/ DDNS/ RS-232/ RS-485
1.2 SPECIFICATION
Model Number 8 Channel 16 Channel
MONITORING
Video Input 8 x BNC 16 x BNC
Video Looping 8 x BNC 16 x BNC
Video Output 1xMain Monitor, 1xSpot Monitor, 1xS-video, 1X VGA (Optional)
Display Resolution (Live) 720x480 (NTSC), 720x576 (PAL)
Display Rate 30 IPS per channel (NTSC), 25 IPS per channel (PAL)
Spilt Screen 1, 4, 9 1, 4, 9, 13, 16
RECORDING & PLAYBACK
Compression H.264
Recording Resolution 720x240 (NTSC), 720x288 (PAL) or 360 x 240 (NTSC), 360 x 288(PAL)
Recording Rate 720x240 (NTSC 120 IPS), 720x288 (PAL 100 IPS) or 360 x 240 (NTSC 240 IPS), 360 x 288(PAL 200 IPS)
Recording Quality 4x Levels (Best, High, Medium, Low)
Recording Mode Manual, Scheduled (5 Recording Schedule)
6
Search Mode Schedule, Event (Motion, Alarm)
Playback Speed Fast Forward (x2~x6), Fast Backward (x2~x6), Field by FieldPlayback, Pause
SYSTEM
Languages English, Chinese etc.
Storage 2 x SATA 3.5” HDD
Data Export Medium 1 x USB 2.0 Slot or CD-RW (or DVD-RW)
HDD Management Status, Format, Overwrite, Capacity Warning
Features Firmware Upgrade (USB Flash Drive)
NETWORK
Connection 1 x RJ-45 Ethernet
Protocols Static IP, Dynamic IP, PPPoE
Remote Control via IE viewer
Management, Monitoring, Recording, Playback
INTEGRATION
Audio In/Out 1 x RCA In, 1 x RCA Out
Alarm In/Out 8x In (NO or NC), 1 x Out (NOor NC)
16x In (NO or NC), 1 x Out (NO or NC)
PTZ Control Protocols 1 x RS-485 (Pelco P, Pelco D & etc.)
Motion Detect (sensitivity 1-100)
Yes (30x24 grids)
User Interface Front Panel Buttons, IR Remote Controller, USB Optical Mouse
OTHER
Dimensions (W x H x D) 430x 88 x 382 mm
Unit Weight 6.5 kg (without HDD) 6.5 kg (without HDD)
Operating Temperature 0 ~ 45 ℃
Operating Humidity 0 ~ 90%
7
Power AC 90V~260V
Approvals UL, CE, FCC
8
2 HARDWARE OVERVIEW 2.1 FRONT PANEL
1 0 41 2
6
3
7
5
89
R E C 1 2 3 4 5
6 7 8 9 + 1 0
C O P YS T A T U SP T ZS E L E C TZ O O MA U T OM E N U
R E W
-
F F
+
a. 16 Channel DVR OPERATION NO. LABEL OPERATION PTZ
1 Power/ Rec. LED Indicator on Power and Recording 2 Recording Recording Button 3 Channel Channel Button (Press the button to display full screen)
4 SHUTTLE
& JOG
Shuttle: Fast Forward ×2 ×4 ×8 Fast Backward ×2 ×4 ×8 Jog: Picture By Picture Playback
5 IR Sensor
Remote Controller IR Sensor
6 LED Play/ HDD/ Network/Alarm (Left to right)
7 CONTROL PANEL Record, Playback And Control Button.
8 USB Connector.
9 USB Mouse Connector (Only by supplied mouse). 10 CD/ DVD RW Slot For CDRW or DVD RW.
Note: 1. User can select camera by using the channel keys on DVR front panel. For example, user can press “+10” key and then press “6” key to see the 16th channel camera image.
2. under the Full and 16 split screen condition, press SELECT button to switch AUDIO ON/OFF.
3. Please plug in the supplied mouse to DVR mouse connector before turn on the DVR. DO NOT REMOVE and PLUG IN the supplied mouse while DVR is operating.
SHUTTLE
JOG
SHUTTLE
JOG
9
10 41 2
6
3 5
89
7
REC 1 2 3 4
5 6 7 8
COPYSTATUSPTZSELECTZOOMAUTOMENU
REW
-
FF
+
b. 8 Channel DVR OPERATION NO. LABEL OPERATION PTZ
1 Power/ Rec. LED Indicator on Power and Recording 2 Recording Recording Button 3 Channel Channel Button (Press the button to display full screen)
4 SHUTTLE
& JOG
Shuttle: Fast Forward ×2 ×4 ×8 Fast Backward ×2 ×4 ×8 Jog: Picture By Picture Playback
5 IR Sensor
Remote Controller IR Sensor
6 LED Play/ HDD/ Network/Alarm (Left to right)
7 CONTROL PANEL Record, Playback And Control Button.
8 USB Connector.
9 USB Mouse Connector (Only by supplied mouse). 10 CD/ DVD RW Slot For CDRW or DVD RW.
Note: 1. User can select camera by using the channel keys on DVR front panel. 2. Please plug in the supplied mouse to DVR mouse connector before turn on the
DVR. DO NOT REMOVE and PLUG IN the supplied mouse while DVR is operating.
SHUTTLE
JOG
SHUTTLE
JOG
10
2.2 BACK PANEL
NO. LABEL OPERATION
1 VIDEO OUTPUT Video output with BNC connector.
2 VIDEO INPUT Video input with BNC connector.
3 POWER Power switcher: AC100V~AC240V / 47-63Hz input.
4 VGA D-SUB OUT Connect to CRT or LCD monitor.
5 ETHERNET RJ-45 connector for network.
6 ALARM 25 pin D-Sub connector for Alarm input.
7 AUDIO OUT Audio output.
8 AUDIO IN Audio input.
9 RS-232 / RS-485 9 pin D-Sub connector for external control unit.
10 SPOT SPOT video output.
11 MONITOR OUT Video output with S-Video connector.
12 MONITOR OUT Video output with BNC connector.
13 FAN Cooling fan.
11
NO. LABEL OPERATION
1 POWER Power switcher: AC100V~AC240V / 47-63Hz input.
2 VGA D-SUB OUT Connect to CRT or LCD monitor.
3 ETHERNET RJ-45 connector for network.
4 ALARM 25 pin D-Sub connector
5 RS-232/485 9 pin D-Sub connector
6 VIDEO OUTPUT Video output with BNC connector.
7 VIDEO INPUT Video input with BNC connector.
8 AUDIO OUT Audio output
9 AUDIO IN Audio input.
10 SPOT OUTPUT Spot Output
11 MONITOR OUT Video output with BNC connector.
12 MONITOR OUT Video output with S-Video connector.
2.3 ADVANCED ZOOM, PTZ & COPY KEY CONTROL ZOOM: In the full screen mode, user can use “ZOOM” button on the front panel to
perform ZOOM function. Press ▲▼◄►, located on the front panel, to move the zoom window.
PTZ: When camera supported PTZ function, user can use “PTZ” button, located on the front panel, to perform PTZ function. Press ▲▼◄► to select and change setup value.
COPY: Within the playback mode, press “COPY” button to start backup record and press
“COPY” again to end backup.
12
2.4 CAMERA & MONITOR LOOPING
Here recommend link cameras by sequence to avoid unexpected image broken, from CH1, CH2, CH3, CH4…….
2.5 EXTERAL ALARM
There are three types of alarms that the system can be configured to handle. They are Motion detection Alarm, External Alarm and Video Loss Alarm. A. Motion detection Alarm and External Alarm:
When motion detection or External Alarm was triggered, there are 5 possible actions will be taken. a. Changes recording speed as alarm recording speed. b. Monitor will display corresponding full screen alarm channel, it will switch
automatic mode to manual mode if buttons pressing activity occurred in 5 seconds. c. Relays can be activated by motion detection or external alarm when turning on. d. External alarm will be recorded in the event list. Motion detection can be set to yes
or no. e. The camera title will be transformed into color of yellow when motion is happening,
“ALARM” text will show up when external alarm is triggered.
B. Video Loss Alarm:
The default setting of Video Loss alarm is enabled and cannot be changed. Although buzzer action can be disabled, an ALM record will still be added to the Event List that indicates the precise time of video loss.
C.25 PIN D-Sub connector is used for external alarm input. It will accept TTL/CMOS
type trigger signals where the 16ch DVR alarm inputs will be set by signal polarity. It also accepts contact type devices. For example, N.O. relay input, the Alarm Polarity should set to LOW in the ALARM SETUP menu. For N.C. relay input, the Alarm Polarity should set to HIGH in the ALARM SETUP menu.
Connector pins 1-16 are for TTL/CMOS compatible alarm signals or for connect one side of the contact type devices. Connector pins 20-21 are for input signal grounding or the remaining side of the contact type devices. The alarm hold input accept TTL/COMS alarm signal as well as contract device. The connector pin 22 connected to Alarm Reset. The Alarm Reset signal return connects to ground pin (pin 20-21).
13
Alarm output is Relay Type, Pin 23 is Normal Close and Pin 25 is Normal Open. These outputs can be used to control external devices.
EXAMPLE 1: Connect with PIR (Passive Infrared) device from ALARM1 INPUT. EXAMPLE 2: A Normal off (Normal Open) alarm siren at Alarm Output.
EX1 EX2
D-SUB25 PIN DEFINE 1-16 Alarm 1-Alarm 16 Camera alarm input 17-19 N/A 20, 21 GND (connecting to ground) 22 Alarm Reset 23 Alarm output, N.C. 24 Relay COM 25 Alarm output, N.O.
14
2.6 IR REMOTE CONTROL
ITEM
AUTO Press AUTO to switch channel by channel automatically.
SEL
Press this button to select the different assembled of camera formats or perform PTZ functions. Moreover, under the 16 split screen and full screen modes, press this button for switching Audio ON/ OFF.
.REC Press REC to start recording & again to stop.
1-16 Press the button to select the channel for full screen.
Fast backward
Picture by picture backward play
Picture by picture forward play
Fast forward
Play video forward
MODE Split Screen Switch
ID **ID setup to control DVRs
▲ Switch split screen & Move upward or increase.
► Switch split screen & Move right or increase.
▼ Switch split screen & Move downward or decrease.
◄ Switch split screen & Move left or decrease.
To enter item or make choose.
MENU To into or exit main menu
MENU STOP
MODE
1 2 3 4
8765
9 10 11 12
16151413
AUTO SEL
PB
REC
ZOOM
ID
STOP Stop play and playback **Each DVR can setup its own ID number. The user can control DVR via remote controller by pressing ID button first and then ID number of DVR and ID button again of remote controller. For example, if DVR is set to 1, the user has to press ID button+ 1+ ID button again of remote controller to control this DVR.
15
2.7 PTZ (PAN, TILT AND ZOOM) CAMERA Following diagram for DVR connect between PTZ camera & joystick controller, for DVR to control PTZ camera please make sure the CAMERA ID, BANDRATE (default at 9600 bps) and RS-485 cable.
0 1 0 10 1 0 1
A B A BA B A B
D+ D- D+ D-D+ D- D+ D-
A B A BA B A B
D0+ D0- D1+ D1-D0+ D0- D1+ D1-
D0+ D0- D1+ D1-D0+ D0- D1+ D1-
A B A BA B A B
R+ R- T+ T-R+ R- T+ T-R+ R- T+ T-R+ R- T+ T-
DVR 1ID 1
DVR 2ID 2
Dome Cam 1CH 1ID 1
Dome Cam 2CH 2ID 2
Dome Cam 3CH 3ID 3
Dome Cam 4CH 4ID 4
Dome Cam 1CH 1ID 1
Dome Cam 2CH 2ID 2
Dome Cam 3CH 3ID 3
Dome Cam 4CH 4ID 4
DATA+DATA-
Up to 16CH
D+ D- D+ D-D+ D- D+ D-
Up to 128 ID
Dome Cam 1ID 1
Dome Cam 2ID 2
R+ R- T+ T-R+ R- T+ T-Dome Cam 3ID 3Up to 128 ID
Up to 32 ID
Up to 16CH
16
3 SYSTEM SETUP 3.1 MENU SETUP INTERFACE(GUI)
A. CAMERA SET B. MOTION SETUP
C. RECORD SETUP D. ALARM SETUP
E. HARD DISK SETUP F. NETWORK SETUP
17
G. BACKUP SETUP H. SYSTEM SETUP
18
3.2 LIVE VIEWING AND POP-UP MENU
NOTE：The pop-up menu can be activated by moving the mouse cruise to the bottom
of the live viewing screen.
A. MENU BAR With live viewing mode, press this button to get into the GUI menu.
B. DISK INFORMATION with live viewing mode; press this button to display disk information.
C. RECORD BACKUP--- Show in Playback mode With live viewing mode, press this button to backup record (.264 video backup) and
press this button again to finish backup. For performing the single image backup (.Y42 single image backup), press first and then click this button to backup the necessary image.
D. DIGITAL ZOOM
19
In the full screen mode, right-click the button of the mouse to pull a range to zoom in or zoom out the image. Users can left-click the button of the mouse to disable this function. (NOTE: Using the mouse to operate digital zoom can zoom in to max. 16 times.) Moreover, user can also use ZOOM key on the front panel to perform this function. (First, click ZOOM Key and then click ▲▼◄► key to select zoom in or zoom out position. Finally, click ENTER key to complete the setting. Moreover, click ZOOM Key again can disable digital zoom function. Using the panel key to perform zoom in function is fixed at 2 times.)
E. PTZ CONTROLLER Within live-viewing mode, Clicks this button to get into the PTZ setup menu. User can also use PTZ key on the front panel to perform this function.
NOTE： Only for the camera supported PTZ function. PTZ CONTROL
, , , Direction key
/ Zoom In/Out key
Under PTZ control mode, press
into PTZ setup menu. User can also press the “MENU” key on the DVR front panel to get into PTZ setup menu.
User can press key to
process PRESET POINT SETUPTo process AUTO function.
20
PTZ SETUP MENU Pan Speed: User can select the speed of Pan function. Tilt Speed: User can select the speed of Tilt function. Auto Speed: User can select the speed of Auto function. Baud Rate: User can select the fixed Baud Rate for PTZ camera. Protocol: User can select the fixed Protocol for PTZ camera.
F. AUDIO CONTROL Press this button to turn the audio on or off。
G. DISPLAY CONTROL Within live-viewing or playback mode, use display control to switch the camera channel.
H. RECORD AND PLAYBACK CONTROL Same as front panel controller and remote controller.
21
NOTE: Display the type of the event as follows.
V.LOSS When a camera signal is lost, the icon will display on the corresponding channel.
ALARM When ALARM is triggered, the icon will display on the corresponding channel.
MOTION When MOTION is detected, the icon will display on the corresponding channel.
3.3 CAMERA SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options.
A. CAMERA
Press ◄ or ►/ mouse wheel to switch channels. B. VIDEO ADJUST
B-1. CONTRAST
Press ◄ or ►/ mouse wheel to change contrast level. B-2. BRIGHTNESS
Press ◄ or ►/ mouse wheel to change brightness level. B-3. HUE
Press ◄ or ►/ mouse wheel to change HUE level. B-4. COLOR
Press ◄ or ►/ mouse wheel to change color level. B-5. SHAPRNESS
Press ◄ or ►/ mouse wheel to change sharpness level.
22
C. CAMERA TITLE
Use mouse to select and change character. Max. 8 characters.
D. DISPLAY
Press ◄ or ► to/ mouse wheel change value for the corresponding camera would be displayed on the screen or not.
E. AUTO SWITCH
Press ◄ or ►/ mouse wheel to ON/OFF auto switch and the switch sec..
F. PTZ SETUP
LEFT-RIGHT SPEED: Use the mouse wheel to change the left-right speed. UP-DOWN SPEED: Use the mouse wheel to change the up-down speed. AUTO SPEED: Use the mouse wheel to change the auto detection speed. BAUD RATE: Use the mouse wheel to change the BAUD rate。 PROTOCOL: Use the mouse wheel to change the connection protocol.
23
3.4 MOTION SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options.
A. CAMERA
Press ◄ or ►/ mouse wheel to switch channels. B. MOTION DETECTS
Press ◄ or ►/ mouse wheel to change value for motion detect function. C. BUZZER
Press ◄ or ►/ mouse wheel to change value for buzzer while motion detected. D. SENSITIVITY
Press ◄ or ►/ mouse wheel to change sensitivity value from 001 (minimum) to 100 (maximum).
E. AREA SETUP 1. Press into SET to enter Motion Area Setting. (Note: The default setting of all
area is “MOTION ON”.)
2. Use the mouse to select which block is needed.
24
3. Left-Click the mouse to see more options or exit the setup.
3.5 RECORD SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options. A. RESOULTION
Press ◄ or ►/ mouse wheel to switch record resolution. 720 x 240 (NTSC)/ 720 x 288 (PAL). 360 x 240 (NTSC)/ 360 x 288 (PAL).
The green area shows the area without motion detection.
SELECT: Cancel the selected area.
CLEAR: Select the area without motion detection.
EXIT: Exit the motion detection setup.
25
B. NORMAL RECORD PPS Press into SET to change the IPS in normal recording. User can click “AVERAGE” to set PPS automatically by system or change the IPS for each channel manually.
C. ALARM RECORD PPS
Press into SET to change the IPS in normal recording. User can click “AVERAGE” to set PPS automatically by system or change the IPS for each channel manually.
D. ALARM RECORD DURATION
Press ◄ or ► to set dwell time of alarm recording. E. RECORD QUALITY
Press into SET to switch image quality of each channel. User can use mouse wheel to change the image quality of each single channel: LOW/ MEDIUM/ HIGH/ BEST, or use “AVERAGE” to switch the image quality of all channels at once.
F. RECORD MODE
Press ◄ or ► to switch record mode to ALWAYS/ MOTION/ SCHEDULE / OFF. G. AUDIO RECORD
Press ◄ or ► to switch AUDIO RECORD ON or OFF.
26
H. SCHEDULE SETUP
Press SET to get into schedule setup menu。
1. Use mouse to select schedule day/ time/ mode.
2. Click to save change and exit.
3.6 ALARM SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options. A. EXT. ALARM MODE
Select N.C for “normal close” alarm input, or select N.O for “normal open” alarm input.
B. ALARM DISPLAY MODE Press ◄ or ►/ mouse wheel to change value for ALARM DISPLAY MODE with full screen.
C. VIDEO LOSS DETECTS Press ◄ or ►/ mouse wheel to switch VIDEO LOSS ALARM ON or OFF.
D. EVENT LOG SETUP Press into SET to change value for MOTION EVENT / VIDEO LOSS EVENT to ON / OFF.
E. BUZZER TIME SETUP
27
Press into SET to set dwell time of BUZZER/ ALARM. F. RELAY TIME SETUP
Press into SET to set dwell time of RELAY.
3.7 HARD DISK MANAGEMENT SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options.
A. OVERWRITE MODE
Press ◄ or ► to change value OVERWRITE MODE ON or OFF. B. CAPACITY WARNING (When Overwrite Mode is OFF, Capacity Warning will
enable) Press ◄ or ► to change value to 20/ 15/ 10 or 5% with non-overwrite mode. When LEFT RATIO is below the setting, it will enable AUDIBLE ALARM (If AUDIBLE ALARM of BUZZER of ALARM SETUP is ON).
C. HDD INFORMATION Press SET to display HDD information.
D. HDD FORMAT SETUP
D-1. HDD PASSWORD PROTECT Press ◄ or ►/ mouse wheel to change value for hard disk format password protection.
D-2. HDD PASSWORD Press into SET then use mouse to change password. Default password： 1111
28
D-3. HDD FORMAT Press into SET to get into FORMAT setup. Press YES or NO to execute.
29
3.8 NETWORK SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options. A. IP MODE
Press ▲ or ▼ to select items and ◄ or ►/ mouse wheel to change to STATIC IP or DHCP.
B. HTTP PORT Press ▲ or ▼ to select items and ◄ or ►/ mouse wheel to change WEB PAGE PORT.
C. IP ADDR Press ▲ or ▼ to select items and SET to change IP ADDRESS. D. NETMASK
Press ▲ or ▼ to select items and SET to change SUBNET MASK. E. GATEWAY
Press ▲ or ▼ to select items and SET to change Default GATEWAY. F. DNS1
Press ▲ or ▼ to select items and SET to change DNS. G. DNS2
Press ▲ or ▼ to select items and SET to change OTHER DNS. H. PPPoE
H-1. PPPoE SETTING Press◄ or ►/ mouse wheel to ENABLE / DISABLE PPPoE.
H-2. USER NAME
30
Use mouse to setup user name for ADSL account. H-3. PASSWORD
Use mouse to setup password for ADSL account. H-4. STATE
Press SET to display status of PPPoE。 I. DDNS SETUP
I-1.DDNS SETTING：Press◄ or ►/ mouse wheel to set DDNS ENABLE / DISABLE.
I-2 PROVIDER：Press◄ or ►/ mouse wheel to select DDNS provider. I-3 USER NAME：Press SET to setup user name. I-4 UPDATE SCHEDULE： Use SET to dwell time of updating schedule. I-5 STATE：Press SET to display status of DDNS。
3.9 BACKUP SETUP
NOTE: For function stability, Ethernet remote control function (IE) will be stopped when processing backup function.
A. USB BACKUP
31
Due to each USB device with different USB driver ICs, their compatibilities differ, too. This system is compatible with most of USB flash memory. If there is compatible issue, please refer to APPENDIX B. In addition, please format USB flash memory with FAT32. BEFORE BACKUP A. In live viewing mode, insert USB device into a USB port of the DVR. B. Get into playback mode by PLAY TIME SEARCH or EVENT LIST SEARCH and
play back videos that are going to be as backup.
VIDEO BACKUP
In multiplexer or full screen mode, press to start backup and press to end backup. The system will backup automatically.
PICTURE BACKUP
In multiplexer or full screen mode, press ► and press the system will start backup picture by picture.
USB BACKUP MENU
User can use the mouse wheel to change the backup Start/ End time。
Click to start backup, the total process will be shown on screen.
BACKUP FILE NAME Each backup file will be named as START TIME. EXAMPLE: 174624.264 is 17:46:24
32
AFTER BACKUP After backup, the system will copy “R6VIEWER.EXE” automatically on USB device for the user to play back backup file.
B. CD/DVD BACKUP
BEFORE BACKUP Please insert a blank CD or DVD into the CD or DVD /RW.
Note: Please DO NOT use blank CD to backup records while using DVD/RW.
CD/DVD BACKUP MENU
User can use the mouse wheel to change the backup Start/ End time.
Click to start backup.
BACKUP FILE NAME Each backup file will be named as START TIME. EXAMPLE: 03311041.264 is March 31st 10:41 AFTER BACKUP After backup, the system will copy “R6VIEWER.EXE” automatically on USB device for the user to play back backup file.
33
3.10 SYSTEM SETUP
Press ▲ or ▼ to select items. Press ◄ or ► to change values. Press into SET to see more options.
A. DATE / TIME SETUP Press SET to set DATE / TIME.
A-1. TIME Use mouse wheel to change DATE/ TIME.
A-2. DATE FORMAT Use mouse wheel to change DATE. There are DD/MM/YYYY, YYYY/MM/DD and MM/DD/YYYY three modes.
A-3. NTP MODE Use mouse wheel to change NTP. When NTP is enable, use SET to change SERVER IP and use ◄ or ►/ mouse wheel to change GMP and UPDATE TIME.
B. SPOT MONITOR SETUP
There are FULL SWITCH、QUAD SWITCH and OFF options for spot monitor display.
34
FULL SWITCH MODE
QUAD SWITCH MODE C. SYSTEM TYPE
Press ◄ or ►/ mouse wheel to change the system type. D. KEYBOARD LOCK
Press ◄ or ►/ mouse wheel to switch ON/ OFF. OFF：UNLOCK. ON： LOCK.
After KEYBOARD LOCK mode setup, please set up PASSWORD Without password, un-authorized users could access into SYSTEM SETUP and make changes of settings easily.
E. ID NUMBER Press ◄ or ►/ mouse wheel to change values. ID NUMBER is required to make difference of each DVR.
F. DISPLAY SETUP Press SET to ENABLE or DISABLE display of CAMERA TITLE / DVR STATUS / DATE / TIME.
G. LANGUAGE Press ◄ or ► to change on-screen-display (OSD) language.
H. PASSWORD PROTECTION Press ▲ or ▼ to select items and ◄ or ► to change values. Default password: 1111.
I. FIRMWARE UPDATE Press YES to start firmware update. After updated, the DVR will reboot automatically. At this moment, please do not turn off the DVR manually. NOTE: 1. Please format USB flash memory with FAT32.
2. For function stability, we suggest user to STOP recording function before processing firmware update function.
J. LOAD DEFAULT
Press SET button to entry CONFIGURE SET screen. There are LOAD SETUP FROM DEFAULT, LOAD SETUP FROM USB and BACKUP SETUP TO USB three parts.
35
J-1. LOAD SETUP FROM DEFAULT: Press SET button to load the setting back to
factory default. J-2. LOAD SETUP FROM USB: Press SET button to load the pen drive setting to the
current DVR. J-3. BACKUP SETUP TO USB: Press SET button to backup the current DVR setting
into pen drive.
K. DAYLIGHT SAVING TIME SETUP Press ◄ or ►/ mouse wheel to change the DAYLIGHT MODE option: Disable,
Manual and Auto.
K-1. MANUAL MODE
Use SET to change the Day Light Saving start and end time.
Press ◄ or ►/ mouse wheel to change DELAY TIME
K-2. AUTO MODE
Press ◄ or ►/ mouse wheel to change CITY option. Different CITY will have different START, END and DELAY TIME.
36
37
4 DVR PLAYBACK
Click the playback button on the pop-up menu.
Playback Display
Note: the pop-up menu can be activated by moving the mouse cruise to the bottom of the live viewing screen. Note: Under playback mode, it will output sound when switch to full screen mode.
38
Note: Under 13 split screen mode, user can see the live-time image from the middle channel and select the channel number by using mouse wheel.
Note: Only 16 channel DVR has this function 4.1 TIME SEARCH
Double click Left button of mouse to trigger play time search.
Please set the start and end time to search.
Live-Time Image
39
4.2 EVENT SEARCH
Double click Left button of mouse to trigger event search.
Please select the event to playback。
NOTE: Display the type of the event as follows.
POWER If the DVR got power loss, it will record the date and time of rebooting.
RECORD If REC. button has been pressed, it will record the date and time in the event list.
V.LOSS When a camera signal is lost, it will record the date, time, and corresponding channel.
ALARM When ALARM is triggered, it will record the date, time, and corresponding channel.
MOTION When MOTION is detected, it will record the date, time, and corresponding channel.
40
5 BACKUP PLAYBACK
SYSTEM REQUIREMENT CPU: Intel Celeron 1.6G MEMORY: 256MB. VGA: 32MB VGA RESOLUTION: 1024 x 768. OS: Windows XP / 2000 SUGGESTED REQUIREMENT CPU:Intel P4 2.8G MEMORY:512MB or above VGA:64MB or above VGA RESOLUTION:1024 x 768 OS: Windows XP / 2000 NETWORK BANDWIDTH: Upload Speed is 256kbps or above 5.1 MAIN SCREEN SETTING
A. MAIN SCREEN
Open File
Play Pause
Channel Selected
Save as AVI
Time & Event Search
41
B. HDD PLAY
Play about all the data from the Hard disk of DVR or perform the specific Time and Event Search to play. Note: Unload the DVR HDD first and connect to the PC to play the HDD. DVR
software (R6Viewer.exe) can get from USB Playback, DVD-RW Playback and “Player” within “Others” blank of Network viewing.
B-1. TIME SEARCH
Insert search Date and Time and then click to play all the searched film.
42
B-2. EVENT SEARCH
It will display all the events which are reserved within the DVR HDD after
press (Shown in the following) and double click left button of mouse to trigger event.
(R6 Viewer.exe) can play not only DVR H.D.D. but also the *.264 and *.Y42 files which are reserved within the data storage devices. (i.e. CD/DVD disc, pen drive and the PC H.D.D which the data backup from DVR H.D.D)
C. File (*.264) Play
D. File (*.Y42) Play
43
5.2 CD/DVD BACKUP PLAYBACK
A. Insert the CD/DVD disk into CD/DVD ROM, the software will auto pop out, and select
"Load File" and pick up the file.
B. Press “Play” button to play the video.
44
5.3 USB & LOCAL BACKUP FILE PLAYBACK
A. Plug the USB disk into PC or check the local backup folder.
If using USB mode, please double click the player.exe from the pop-up diagram. (As below)
B. The play backup program would appear on the screen, select "Load File".
45
C. Open the USB disk located driver letter. (Example E:) or the local backup folder, and
pick the file to playback. The backup file will named as the time when backup, as like: 170319.264 will be 17:03:19
D. Press the play icon to play the video or still picture.
46
5.4 BACKUP FILE TO AVI A. Please select specific channel to backup.
B. During video playback mode please press AVI bottom to start. C. Make up a filename and path than press bottom to start AVI backup.
D. Press AVI bottom to finish backup.
47
6 NETWORK VIEWING & PLAYBACK
SYSTEM REQUIREMENT CPU: Intel Celeron 1.6G MEMORY: 256MB. VGA: 32MB VGA RESOLUTION: 1024 x 768. OS: Windows XP / 2000 SUGGESTED REQUIREMENT CPU:Intel P4 2.8G MEMORY:512MB or above VGA:64MB or above VGA RESOLUTION:1024 x 768 OS: Windows XP / 2000 NETWORK BANDWIDTH: Upload Speed is 256kbps or above 6.1 IP ADDRESS SETUP ON PC SITE
Install cameras inside in LAN or use network cable to connect with PC. This is for IPInstallerEng.exe to set up IP address of cameras. If OS is Windows XP SP2 or above, the following Windows Security Alert will popup. Then, please click on Unblock. Then, IP Manager Eng.exe will popup: DVR default IP address is 192.168.1.220
48
NOTE: Please input correct network parameters without blank spaces. On Device Lists, it lists all servers. Click on one server and then its IP setting will show on the right side. After editing the parameters and clicking on Submit, the following dialogue box will popup. And, it will reboot the device with new parameters.
6.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETUP OPTION 1: DISABLE ACTIVEX WARNING A. IE Tools Internet Options Security Custom Level Security Settings
Download unsigned ActiveX controls Enable or Prompt (recommend). B. IE Tools Internet Options Security Custom Level Security Settings
Initialize and script ActiveX controls not marked as safe Enable or Prompt (recommend).
49
1 2
3 4
5
Above three options are all based on select as the prompt. As indicated in the dialogue box. Please select "YES."
50
OPTION 2: ADD TO TRUSTED SITES
IE Tools Internet Options Security Trusted sites Sites
192.168.1.220
51
6.3 LOGIN
A. INSTALL ACTIVEX
B. ACCOUNT & PASSWORD LOGIN After IP setup and connect to network or LAN, type IP address on IE Browser directly. The following User name & Password Login window will popup.
Default user name: admin
Default password: admin
192.168.1.220
52
6.4 REMOTE CONTROL
LIVE VIEWING
A. DVR Configuration Get into DVR network menu. B. SCREEN FORMAT
Switch screen format and click twice to switch different channels with full screen.
C. REC. Videos are saved as AVI file.
D. Playback
E. Time-Point Backup Click , and playback window will popup PLAYBACK by TIME SEARCH & EVENT SEARCH
DVR Configuration
System Time
Screen Format
Play Back
REC
PTZ Control
Full Screen
Time-Point Backup
Playback Time Search Time
53
Event Search
HDD Select
Ex. HDD1 or HDD2
54
A. HDD Select
User can select HDD1 or HDD2 for playback B. Playback Time
User can select the time then press “Time Search” for playback. C. Time Search
User can select the time then press “Time Search” for playback. D. Event Search
User can select event item by pressing “Event Search” for playback.
Click to operate Time-Point backup. TIME-POINT BACKUP First, select Start and End backup time which have to among the Record Time.
Then, click Save button to select the position on PC where the user is going to backup the data. After that, press OK button to start the backup.
Finally, double-click the left button of the mouse to open the saved backup file. The backup file
will named as the time when start to backup, such as, (20080526113258.264) will be 2008/05/26 11:32:58.
55
OTHER FUNCTIONS
User can use other functions by clicking the left of mouse A. Snapshot: User can save any single picture from image. B. Performance: User can select image quality (high, medium & low). C. Use Overlay: User can use Overlay function. D. Play audio: User can play audio function by channel. Note: remote user can receive audio from DVR & the audio will be saved with image when processing video backup.
56
6.5 CONFIGURE A. System - System Information
A-1 SYSTEM INFORMATION SERVER NAME: This name will show on the IP Installer. LANUGAGE：There are English, Traditional Chinese, and Simplified Chinese.
A-2 NTP Setting NTP SERVER: Revise the time of DVR via different NTP Server.
Note: Time zone and Interval cannot adjust in here (User can adjust both in DATE and TIME SETUP option of DVR Menu).
B. SYSTEM – USER MANAGEMENT
57
User Management provides 3 levels of limits of authority: Administrator (the highest), User, and Guest. Administrator: Possessing the highest level of authority to operate full functions
within network. User: Having Live Image and Video Playback authority. Moreover, PTZ controlled
is included as well. Guest: Only have Live Image authority. Default administrator account: Username: admin Password: admin
B-1 ANONYMOUS USER LOGIN:
YES: Accept anonymous user login without password as guest login. NO: Anonymous login unacceptable.
B-2 USER MANAGEMENT: Add: Input Username and Password and then click on Add/Set to save. Modify: Click on selected User name on User List and the following window
will popup. After inputting Password and Confirm Password, click on OK.
Remove: Click on selected User name on the user list and click on Remove.
58
C. SYSTEM / SYSTEM UPDATE Click on the “Browse” button to select the latest firmware and then press “Upgrade” button to upgrade the firmware.
D. NETWORK – IP SETTING
59
D-1 IP ASSIGNMENT DHCP: In Dynamic Host Configuration Protocol (DHCP) mode, DHCP
server will get setting done automatically.
STATIC IP: Please input IP address, Subnet Mask, and Gateway based on network environment.
D-2 PORT ASSIGNEMENT
With IP Share (Router), the following Ports needed to be adjusted in case of conflict.
E. NETWORK – PPPoE
60
E-1 PPPoE SETTING
Click on Enabled to enable ADSL dial function. Username: Username for ADSL account. Password: Password for ADSL account.
After dialed successfully, new IP address will appear.
E-2 SEND MAIL AFTER DIALED
Click on Enabled to enable SEND MAIL AFTER DIALED function.
E-3 SUBJECT Mail subject.
F. NETWORK / DDNS SETTING
61
Click on Enabled to enable DDNS function. F-1 DYNDNS.ORG
DDNS SETTING - DYNDNS.ORG PROVIDER: Select dyndns.org HOSTNAME: The registered hostname in DYNDNS.ORG. USERNAME: The registered username in DYNDNS.ORG. PASSWORD: The registered password in DYNDNS.ORG. SCHEDULE UPDATE: A period of time to update IP address. STATE 1. Updating: Information update.
2. Idle: Stop service. 3. DDNS registered successfully, now log by
62
http://<username>.ddns.camddns.com: Registered successfully. 4. Updating Failed, the name is already registered. 5. Updating Failed, please check your internet connection.
F-2 DDNS.CAMNNDS.COM
DDNS SETTING – DDNS.CAMDDNS.COM PROVIDER: Select ddns.camddns.com USERNAME: The registered username in DDNS.CAMDDNS.COM. SCHEDULE UPDATE: A period of time to update IP address.
STATE 1. Updating: Information update.
2. Idle: Stop service. 3. DDNS registered successfully, now log by
http://<username>.ddns.camddns.com: Registered successfully. 4. Updating Failed, the name is already registered. 5. Updating Failed, please check your internet connection.
G. NETWORK / Mail & FTP
63
Click on “Motion” or “Alarm” option to enable Mail Setting and FTP Setting function. Mail Server: The IP address of Mail Server (i.e. mail.huntelec.com.tw). Username: The username while log in to the mail server. Password: The password while log in to the mail server. Sender’s Mail: The sender’s account when send the mail via this mail server. Receiver’s Mail: The receiver’s mail address. Bcc Mail: The receiver’s mail address for Bcc Mail. Event Subject: The subject of this mail. (Default value is ALARM MAIL) FTP Server: The IP address of FTP Server. Username: The username while log in to the ftp server. Password: The password while log in to the ftp server. Port: The port number of file transmission. (Default value is 21) Path: The ftp path where the user wants to reserve the information. Finally, click on Apply button to reserve the setting.
H. OTHERS / Player Downloaded User can click “Run” button to download the player to local PC.
64
I. OTHERS / RTSP User can click Video Quality drop down list to change the video quality. There are Best, High, Standard, Medium and Low options.
65
7. 3GPP APPLICATION & SETTING 3GPP (also known as 3rd Generation Partnership Project) is a corporation which formulate
3rd-generation communication standard specification. Via this wireless communication protocol, the 3G mobile can perform the remote control. The following example is operated by Sony Ericsson 3G mobile phone:
1. Press MENU KEY to get into menu. 2. Select Internet services
3. In the Internet services page, press More KEY
4. Select Enter address, and press Select KEY
5. Select New address，and press Enter KEY
6. Fill in address rtsp:// <<IP>>/channel (rtsp://220.137.65.246/CH03) and press Go To KEY.
66
7. “Connected to media server” will appear
8. Success with vivid image
* 1. 3GPP BANDWIDTH: Minimum 30kbit /sec. per channel. 2. CONNECTION NUMBERS: Maximum 16 people per channel.
67
APPENDIX A: RECORDING TIME LAPSE (HOURS) CIF CIF H.264
80GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 13 26 53 108 161
High 23 46 93 186 280
Middle 38 75 155 303 455
Record
Quality
Low 60 121 242 485 728
160GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 26 53 108 215 323
High 46 93 186 373 560
Middle 75 151 303 606 910
Record
Quality
Low 121 242 485 970 1456
250GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 41 84 168 215 505
High 73 145 291 373 875
Middle 118 236 474 606 1422
Record
Quality
Low 189 379 758 970 2275
400GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 67 135 270 539 809
High 116 233 466 933 1400
Middle 189 379 758 1516 2275
Record
Quality
Low 303 606 1213 2427 3640
500GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 82 168 336 430 1010
High 146 290 582 746 1750
Middle 236 472 948 1212 2844
Record
Quality
Low 378 758 1516 1940 4550
750GB HDD
IPS (Image Per Sec.) 240 120 60 30 15
Record Best 123 252 504 645 1515
68
High 219 435 873 1119 2625
Middle 354 708 1422 1818 4266
Quality
Low 567 1137 2274 2910 6825
1T HDD
IPS (Image Per Sec.) 240 120 60 30 15
Best 164 336 672 860 2020
High 292 580 1164 1492 3500
Middle 472 944 1896 2424 5688
Record
Quality
Low 756 1516 3032 3880 9100
FIELD FIELD H.264
80GB HDD
IPS (Image Per Sec.) 120 60 30 15
Best 13 26 53 80
High 24 48 96 145
Middle 38 75 151 227
Record
Quality
Low 60 121 242 364
160GB HDD
IPS (Image Per Sec.) 120 60 30 15
Best 26 108 161 161
High 48 96 145 291
Middle 75 151 227 455
Record
Quality
Low 121 242 364 728
250GB HDD
IPS (Image Per Sec.) 120 60 30 15
Best 41 84 168 253
High 75 151 303 455
Middle 118 236 474 711
Record
Quality
Low 189 379 758 1137
400GB HDD
IPS (Image Per Sec.) 120 60 30 15
Best 67 135 270 404
High 121 242 485 728
Middle 189 379 758 1137
Record
Quality
Low 303 606 1213 1820
500GB HDD
IPS (Image Per Sec.) 120 60 30 15
69
Best 82 168 336 506
High 150 302 606 910
Middle 236 472 948 1422
Record
Quality
Low 378 758 1516 2274
750GB HDD
IPS (Image Per Sec.) 120 60 30 15
Best 123 252 504 759
High 225 453 909 1365
Middle 354 708 1422 2133
Record
Quality
Low 567 1137 2274 3411
1T HDD
IPS (Image Per Sec.) 120 60 30 15
Best 164 336 672 1012
High 300 604 1212 1820
Middle 472 944 1896 2844
Record
Quality
Low 756 1516 3032 4548
APPENDIX B: HDD COMPATIBLE TABLE
Brand Model Capacity Speed (RPM) SEAGATE ST380815AS 80G 7200 10
ST3160815AS 160G 7200 10 STM3250820AS 250G 7200 10 ST3400620AS 400G 7200 10 ST3750640AS 750G 7200 10
WD WD2500AAKS 250G 7200 HITACHI HDS721616PLA380 160G 7200
HDT725025VLA380 250G 7200 HDT725032VLA360 320G 7200 HDP725050GLA360 500G 7200
Last Update Date 2008/3/24
70
* Please use SATA I Hard Disk and setup the Jumper Block to 1.5 Gb/s Operation. As the following image,
* According to the machine test result, SEAGATE Hard Disk ST3500320AC 500G is incompatible for this DVR. Therefore, SEAGATE ST3500320AC 500G is not suggested to use.
Jumper Block
