Guide to Configuration Huawei Usb Fwt Macosdriverv2.9.9

Product name Confidentiality levelFWT For internal use only

Product versionTotal 14 pages

Guide to Configuration of Huawei USB FWT

Mac OS Driver

Prepared by HopeCao (ID: 37496) Date 2008-3-18Reviewed by DateApproved by DateAuthorized by Date

Huawei Technologies Co., Ltd.

All rights reserved

(BY-WTX-T02 V3.20/ IPD-CMM V3.0 / for internal use only)

Guide to Configuration of Huawei USB FWT Mac OS Driver For internal use only

Revision Record

Date Revision Version

CR ID / Defect ID

Sec No.

Change Description Author

2005-12-22 1.0 First draft completed Cao Hepu (ID: 37496)

2006-3-27 1.5 “Configure APN” Section Added

Zhang CongKuan(ID: 60012361)

2006-3-30 2.0 Update the attached driver package

Zhang CongKuan(ID: 60012361)

2006-8-18 2.2 Update the driver package to support INTEL MAC system

HopeCao(ID: 37496)

2006-12-28 2.6 Add EC321/EC325 INFO HopeCao(ID: 37496)

All rights reserved Page 2 of 14


Table of Contents

1 Introduction..............................................................................................................................72 Installing Data Card Driver.......................................................................................................73 Configuring Dialup Connection for Data Card..........................................................................73.1 Insert the data card into the Computer...............................................................................73.2 Open “System Preference”................................................................................................73.3 Click “Network” in “System Preference”.............................................................................83.4 Input PPP parameters........................................................................................................83.5 Input Modem Parameters...................................................................................................9

Modem: Select “HUAWEI Mobile Connect – 3G Modem” in the popup box..............................93.6 Login Dial Up Network.....................................................................................................10



List of Tables

Table 1 Abbreviations and acronyms............................................................................................6



List of Figures

Figure 1 Open System Preference...............................................................................................7Figure 2 System Preference.........................................................................................................8Figure 3 Network – Page “PPP “..................................................................................................9Figure 4 Input Modem Parameters.............................................................................................10Figure 5 Login Dial Up Network..................................................................................................11Figure 6 Network Status - Idle....................................................................................................11Figure 7 Network Status - connected..........................................................................................12



Guide to Configuration of Huawei USB FWT Mac OS Driver

Key words: driver, Mac OS, dialup connection

Abstract: This document introduces how to configure the HUAWEI USB FWT driver and its

dialup connection in a Mac OS.

Acronyms and abbreviations:

Abbreviations Full spelling

Table 1 Abbreviations and acronyms



1 Introduction



This document instructs how to install HUAWEI USB FWT driver in a Mac OS environment

and how to configure the dialup connection for the data card.

The Mac OS referred to in this document is 10.3.3 or later.

2 Installing Data Card Driver

Decompress the “MobileConnectDriver 2.9.9.zip” program packet in the appendix to obtain

one installation packages “MobileConnectDriver 2.9.9 test.pkg”. Double click the package to

install the driver and restart the system.

3 Configuring Dialup Connection for FWT

3.1 Connect FWT to the Computer.

3.2 Open “System Preference”

Figure 1 Open System Preference



Figure 2 System Preference

3.3 Click “Network” in “System Preference”

3.4 Input PPP parameters

Select the “Huawei Technologies” as the follow diagram:

Account Name: a name to identify the dial up network account.

Password: password to login the dial up network.

Telephone Number: must be *#777.



Figure 3 Network – Page “PPP “

3.5 Input Modem Parameters

Modem: Select “HUAWEI Mobile Connect – 3G Modem” in the popup box

Disable the item “Wait for dial tone before dialing

Dialing: Selct the Tone item

Sound: Select the Off item

Click “Apply Now” to apply the settings.



Figure 4 Input Modem Parameters

3.6 Login Dial Up Network

1 Click the button of “Dial Now”, and the “Network Status” dialog will appear.

2 Click “Connect” in the “Network Status” dialog, wait for a minute, then the dial up network

will be connected.



Figure 5 Login Dial Up Network

Figure 6 Network Status - Idle



Figure 7 Network Status - connected



Attachment:


Documents

Guide to Configuration Huawei Usb Fwt Macosdriverv2.9.9