Upload
others
View
4
Download
1
Embed Size (px)
Citation preview
Features
• 13,6 t (15 USt) capacity three-section boom with 12,5 m (41 ft) outreach
• 4,6 m (15 ft) offsettable swingaway extension
• 9072 kg (20,000 lb) deck carrying capacity
• Available with dual fuel engine only
Grove YB5515 (Dual Fuel)Product Guide
Features
CabThe YB5515 comes equipped with a standard open air cab shell with overhead safety glass.
An optional enclosed cab with the addition of front, right, and rear glass, a split (two-piece) hinged door with sliding glass. Front windshield wiper, heater and defroster fan are included.
OutriggersThe YB5515 is equipped with single-position oblique style outriggers.
Dual Fuel engineG.M. 4,3 L V-6 EFI dual fuel (gasoline / L.P.) rated at 69,3 kW (93 bhp) at 2500 rpm.
BoomA 12,5 m (41 ft) main boom comes standard on the YB5515. An optional fourth main boom section adds 3,4 m (11 ft) additional boom length.
SteeringStandard steering modes on the YB5515 is two-wheel, four-wheel, and crab steer with an option for electronic self-alignment.
Contents
Specifications 4
YB5515 dimensions 7
YB5515 three-section boom working range 8
YB5515 four-section boom working range 9
YB5515 three-section boom load chart 10
YB5515 four-section boom load chart 11
YB5515 three-section boom DIN/ISO range diagram 12
YB5515 four-section boom DIN/ISO range diagram 13
YB5515 three-section boom DIN/ISO load chart 14
YB5515 four-section boom DIN/ISO load chart 15
Symbols glossary 16
4
Specifications
*Load moment indicator(hardwired LMI)
“Graphics Display” of boom angle, boom length, loadradius, and capacity. Operator input to set the limitparameters based on the load chart. Displays colorcoded light bar and audible alarm with function cut-outif load exceeds the load chart parameters.
Swing
Ball bearing swing circle with 360° continuous rotation. Hydraulic driven worm gear and pinion.Maximum speed: YB5515: 2.1 rpm
Hydraulic system
Four section gear pump providing a system pressure of 241,3 bars (3500 psi)Combined flow: 333,1 Lpm (88.0 gpm)YB5515: Six-section valve bank mounted in dash with direct mechanical linkage for low effort lever control.Return line filter with full flow by-pass protection and service indicator.151,4 L (40 gal) hydraulic reservoir with sight level gauge and steel side plating to guard against side impact damage.
Hoist specifications
Piston motor drive with spring applied / hyd. released brake. Equal speed power up and down.Drum diameter: 0,25m (9.75 in)Maximum hoist single line pull: 5443 kg (12,000 lb)Maximum hoist single line speed: 38,4 m/min (126 fpm) Maximum permissible single line pull: 3402 kg (7500 lb) (12,7 mm [1/2 in]) Rope length:
(three-section boom) 73,0 m (240 ft)(four-section boom) 88,4 m (290 ft)
Superstructure
Boom
5,6 m – 12,5 m (18 ft 6 in – 41 ft 0 in) three-section full power boom.Maximum tip height: 14,1 m (46 ft 3 in)
*Optional boom
Manual fourth main boom fly sectionMaximum tip height: 17,0 m (56 ft 3 in)
*Boom extension
4,6 m (15 ft) offsettable swingaway extension
Boom nose
Two sheave non-pivoting boom nose
Boom elevation
Single double acting hydraulic cylinder with integral holding valve.Elevation: 0° to 69° for the YB5515
Anti-two block device
Standard anti-two block device, when activated, provides an audible warning to the crane operator and disengages all crane functions whose movement can cause two-blocking.
Load indicator (wireless LSI)
A simple, effective, and easy to use load momentindicating system used in conjunction with a wireless anti-two block system to assist the operator in efficient operation of the unit within the limits of the load chart. The display panel displays the hook load, length and angle of the boom, and load radius in Dot Matrixnumerical values and provides a load utilizationcolored bar graph. If non-permitted conditions are approached the L.M.I. will warn the operator with an audible alarm and a warning light and will lock out those functions thatmay aggravate the condition.Standard limit settings can be programmed for boomAngle, load radius, and boom tip height.
*Denotes optional equipment
Grove YB5515 Dual Fuel 5
Specifications
*Operators control station enclosed
Includes the standard cab shell with the addition of front, right, and rear glass, a split (two-piece) hinged door with sliding glass.Front windshield wiper, heater and defroster fan are included.
Fuel tank capacity
151,4 L (40 gal) all steel construction with steel side plate to guard against side impact.
Electrical system
One 12V maintenance free battery, 820CCA @ 0°. 63 amp alternator.
Drive
4 x 2 – Front axle drive with planetary hubs and limited slip differential.
Steer
Two-wheel, four-wheel, and crab steerOutside turning radius: Two wheel steer: 6,55 m (21 ft 6 in) Four wheel steer: 3,76 m (12 ft 4 in)
Transmission
I.T.L. synchromesh four-speeds forward and reverse.
Tires
385/65R 22.5 radial traction tread pneumatic.
Carrier
Frame
High strength alloy steel constructed with integral outrigger housings; front and rear tie-down lugs. 75 ft2 carrydeck size with 9072 kg (20,000 lb) carrying capacity. Deck coated with anti-skid treatment.
Outriggers
YB5515: Front and rear oblique type beams at all four corners with integral holding valves. Outrigger pads form an integral part of the beam. Outrigger pad size 222 mm x 254 mm (8.75 in x 10 in). Outrigger monitoring system (required for North America and Canada).Maximum pad load: 162 p.s.i.
Outrigger controls
Lever controls located on dash panel and operate the beams in pairs from side to side. Level bubble located inside operators compartment.
*Independent outrigger controls available as an option.
Dual Fuel engine (2007 EPA)
G.M. 4,3 L V-6 EFI dual fuel (gasoline / L.P.) rated at 69,3 kW (93 bhp) at 2500 rpm.
Operators control station
Frame mounted, open air style control station with cab shell includes all crane functions, driving controls, and overhead safety glass. Other standard equipment include a durable weather resistant seat with seat belt, hourmeter, sight level bubble, and fire extinguisher. The dash panel includes engine oil pressure gauge, engine water temperature gauge, fuel gauge, transmission low oil and high temperature warning lights, low battery warning light, and brake system low pressure warning light. The LSI (load indicator) receiver is mounted to the top of the dash.
*Denotes optional equipment
6
Specifications
Brakes
Hydraulic actuated internal wet-disc service brakes acting on all four wheels. A dash mounted toggle switch activates the dry disc parking brake on the transmission output yoke with a dash warning light.
Suspension
Front: Rigid mounted to frame.Rear: Provides 1.5° oscillation for use on semi-rough terrain. Axle lock-out must be engaged (locked) whenever picking on rubber or traveling in the crab steer mode. A warning light indicates when the axle lock-outs are engaged.
Lights
Recessed mounted, includes head, tail, rear work, stop, and turn signals.
Maximum speed
23,3 km/h (14.5 mph)
Gradeability (theoretical)
73%....no load41%.... 9072 kg (20,000 lb) load
Gross vehicle weight (G.V.W.)
12 332 kg (27,186 lb) three-section boom12 584 kg (27,743 lb) four-section boom*All weights with enclosed cab
Miscellaneous standard equipment
Two sheave, “Quick Reeve” style hookblock; 13,6 t (15.0 USt).Back-up alarmLifting and tie down lugsOutrigger motion alarm
*Denotes optional equipment
Grove YB5515 Dual Fuel 7
Dimensions
YB55154,58 m
(15' 0.50")
2,16 m(7' 1")
1,83 m(6' 0")
1,06 m(3' 6")
0,74 m(2' 5")
2,43 m (7' 1 1-1/2")
1,22 m(4' 0")
2,01 m(6' 7")
4,06 m (13' 2-1/2'')
6,73 m(22' 1'')
50,8 cm(1' 8")
4,29 m(14' 1')
Three Section Boom
1,32 m(4' 4")
2,03 mm(8")
0,08 m(3")
2,44 m w/ Enclosed Cab(8' 0" )
3,73 m(12' 3")
1,88 m(6' 2")
1,99 m(6' 6-1/2")
1,24 m(4' 1")
38,1 cm(1' 3")
33,0 cm(1' 1")
Four Section Boom 5,65 m Retracted
(18' 6'')
15,93 m Extended(52' 3")
5,65 m Retracted(18' 6'')
12,50 m Extended(41' 0'')
2,43 m (7' 1 1-1/2")
4,58 m(15' 0.50")
2,16 m(7' 1")
1,83 m(6' 0")
1,06 m(3' 6")
0,74 m(2' 5")
2,43 m (7' 1 1-1/2")
1,22 m(4' 0")
2,01 m(6' 7")
4,06 m (13' 2-1/2'')
6,73 m(22' 1'')
50,8 cm(1' 8")
4,29 m(14' 1')
Three Section Boom
1,32 m(4' 4")
2,03 mm(8")
0,08 m(3")
2,44 m w/ Enclosed Cab(8' 0" )
3,73 m(12' 3")
1,88 m(6' 2")
1,99 m(6' 6-1/2")
1,24 m(4' 1")
38,1 cm(1' 3")
33,0 cm(1' 1")
Four Section Boom 5,65 m Retracted
(18' 6'')
15,93 m Extended(52' 3")
5,65 m Retracted(18' 6'')
12,50 m Extended(41' 0'')
2,43 m (7' 1 1-1/2")
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
8
Range diagram
YB5515 (three-section boom)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Hei
ght
from
the
gro
und
in fe
et
128 10 14 16 18 20 3822 24 26 28 3430 32 36 464240 44 48 50 52 5446 4 2 0 2 6
52
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
44
36
38
40
42
48
46
50
60
56
54
58
6246 4 2 0 2 1286 10 14 16 18 20 3822 24 26 28 3430 32 36 464240 44 48 50 52 54
0
52
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
44
36
38
40
42
48
46
50
60
56
54
58
62
69°
60°
50°
40°
30°
20°
10°
0°
Boo
m a
nd e
xten
sion
leng
th in
feet
Operating radius in feet from axis of rotation
Grove YB5515 Dual Fuel 9
Range diagram
YB5515 (four-section boom)
52
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
44
36
38
40
42
48
46
50
60
56
54
58
62
64
66
68
70
72
128 10 14 16 18 20 3822 24 26 28 3430 32 36 464240 44 48 50 52 54 56 58 60 62 64 660
46 4 2 0 2 6
46 4 2 0 2 1286 10 14 16 18 20 3822 24 26 28 3430 32 36 464240 44 48 50 52 54 56 58 60 62 64 66
52
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
44
36
38
40
42
48
46
50
60
56
54
58
62
64
66
68
70
72
0o
10o
20o
30o
40o
50o
60o
69o
RETRACTEDW/4TH RET
RETRACTEDW/4TH EXT
EXTENDEDW/4TH RET
EXTENDEDW/4TH EXT
15'JIB
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
HEI
GH
T FR
OM
TH
E G
RO
UN
D IN
FEE
T
YB5515 (4-SECTION BOOM)
Boo
m a
nd e
xten
sion
leng
th in
feet
Operating radus in feet from axis of rotation
Hei
ght
from
the
gro
und
in fe
et
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
10
Load chart
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of verticalhoist line or tackle with load applied.
2) The rated loads shown on outriggersdo not exceed 85% of actual tipping. Therated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors a�ecting stability. Hazardous suroundings, climatic conditions, experience of operator andproper training must be taken into account by the operator.
3) The weights of all load handling devices, such as hooks, hook blocks,slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tire capacity, , condition of tires and proper inflation pressure (120 psi). Loads on rubber may be transportedat a maximum speed of 2.5 mph on a smooth, hard, level surface with theboom retracted to the shortest lengthpossible and centered over the front.
6) For operating radius not shown,use load rating of next larger radius.
7) The maximum combined total boom and deck load is 16,000 lb. The maximum deck load only is 20,000 lb.
8) Do not induce any external side loads to boom or jib.
YB5515 (3-SECTION BOOM)
1302442YB
ON OUTRIGGERS (lb)
MA
IN B
OO
MJI
B
ON RUBBER (lb)
14,800
RADIUS(ft)
13,00012,20010,80096308640
14,80013,00012,20010,800
9180
4290
32603060
35803920
53104740
62107480
34803310
29602710
24102210
27002560
2860
5060
40204510
704064205700
7790
3700
72106600
60005250
640570
740690
3190
1320
930860800
116 01040
18201530
22002660
47603900
1040930
4370
1990
1460
12701370
17901610
26202260
30703710
60605120
3130
F/R 360° F/R 360°
30,00026,20022,30018,600
30,00026,20022,30018,600
17,00013,500
17,00014,60010,8808100
10,7008710
14.015.016.018.020.022.024.026.028.030.032.034.036.037.540.042.044.046.048.8
6.08.010.012.0
2390 1940 48079052.5
BOOM
(deg)ANGLE
MAIN
60
40
15
0
3035
4550
2250
1950
-
21502080
3150
26002400
JIB STRUCTURAL
55 2850
25 205020 2000
5 -10 -
69 390065 3500
2800
2100
2000
26002400
4300
34003050
3800
23002200
20202050
60005000
1950
-
-
19001850
2350
21002000
2200
--
--
28002550
15°0° 30°
CAPACITIES (lb)
11901120
0 - 30,000 lb4-PART
0 - 7500 lb1- PART
RIGGING CHART
WIRE ROPE: 1/2 in diameter
Minimum breaking strength 26,250 lb
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
210 lb
100 lb
0 lb
700 lb
N/A
100 lb
N/A
0 lb
FRONT REAR
SIDE
SIDE
15°
30°
15°
30°
YB5515 (three-section boom)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Grove YB5515 Dual Fuel 11
Load chart
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 85% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors a�ecting stability .Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity , condition of tires andproper inflation pressure (120 psi).Loads on rubber may be transported at a maximum speedof 2.5 mph on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 16,000 lb.The maximum deck load only is 20,000 lb.
8) Do not induce any external sideloads to boom or jib.
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1302395YB
0 - 30,000 lb4-PART
0 - 7500 lb1-PART
RIGGING CHART
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 26,250 lb
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
210 lb
100 lb
0 lb
700 lb
N/A
100 lb
N/A
0 lb
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
ON RUBBER (lb)ON OUTRIGGERS (lb)
MA
IN B
OO
MJIB
14,80014.0
RADIUS(ft)
15.0 13,00016.0 12,20018.0 10,80020.0 963022.0 864024.026.028.030.032.034.036.037.540.042.044.046.048.8
58.052.5
14,80013,00012,20010,6008630
4420
31902890
35703950
57005040
64607350
29502760
243022402030
- -
209018501480
24302250
2600
4400
35103930
680058205020
7790
3210
72106600
54804890
-
450380290
550500
3080
1220
770680610
1070920
16101410
19902460
45003750
-
800680500
970890
3980
1880
1280
1070
16501460
23602100
27203230
60604950
2590
F/R 360° F/R 360°
63.8 - - --
ON RUBBER (lb)ON OUTRIGGERS (lb)
8290
RADIUS(ft)
82008110795078207710
83908200
79507820
4760
31902970
35704080
63305420
72707710
34003150
2630232020701720 1380
213019301710
24902300
2700
5180
42504680
710065905710
7630
3830
77607150
75006080
170
470370280
630540
3560
1580
990880740
1360
21501840
25203000
55104500
420
790710590
960870
4730
2190
1370
10701240
18801600
29402550
34103980
66105680
2890
F/R 360° F/R 360°
1330 1020 60230
4TH EXTENDED
30,0006.08.0 26,20010.0 22,30012.0 18,600
30,00026,20022,30018,600
17,00013,500
17,00014,60011,0007650
10,7008710
-11,00010,7009250
-
10,7009250
- -
10,7009250
10,7009250
14.015.016.018.020.022.024.026.028.030.032.034.036.037.540.042.044.046.048.8
58.052.5
63.8
6.08.010.012.0
4TH RETRACTEDBOOM
(deg)ANGLE
MAIN
4TH RETRACTED
60
40
15
0
3035
4550
2250
1950
-
21502080
3150
26002400
JIB STRUCTURAL CAPACITIES (lb)
55 2850
25 205020 2000
5 -10 -
69 390065 3500
4TH EXTENDED
2800
2100
2000
26002400
4300
34003050
3800
23002200
20202050
60005000
1950
-
-
19001850
2350
21002000
2200
--
--
28002550
15°0° 30° 0° 15° 30°
2250
1950
-
21502080
3150
26002400
2850
20502000
--
39003500
2800
2100
2000
26002400
4300
34003050
3800
23002200
20202050
51804970
1950
-
-
19001850
2350
21002000
2200
--
--
2800255011,000 11,000 11,000
8110
1180
1160
YB5515 (four-section boom)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
12
DIN/ISO range diagram
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
YB5515 (three-section boom)
69˚
60˚
50˚
40˚
30˚
20˚
10˚
0˚
18,9
17,7
16,5
17,1
18,3
15,2
14,0
14,6
12,8
12,2
11,6
11,0
13,4
10,4
9,8
9,1
8,5
7,9
7,3
6,7
6,1
5,5
4,9
4,3
3,7
3,0
2,4
1,8
1,2
0,6
0
15,8
16,515,815,214,613,412,2 12,8 14,011,09,89,1 10,48,57,97,36,7 11,66,15,54,94,33,01,8 2,4 3,70,600,61,21,8 1,2
16,515,815,214,613,412,2 12,8 14,011,09,89,1 10,48,57,97,36,7 11,66,15,54,94,33,01,8 2,4 3,70,600,61,21,8 1,218,9
17,7
16,5
17,1
18,3
15,2
14,0
14,6
12,8
12,2
11,6
11,0
13,4
10,4
9,8
9,1
8,5
7,9
7,3
6,7
6,1
5,5
4,9
4,3
3,7
3,0
2,4
1,8
1,2
0,6
0
15,8
Operating radius in meters from axis of rotation
Boo
m a
nd e
xten
sion
leng
th in
met
ers
Hei
ght
from
the
gro
und
in m
eter
s
Grove YB5515 Dual Fuel 13
DIN/ISO range diagram
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
YB5515 (four-section boom)
15,8
0,6
1,2
1,8
2,4
3,0
3,7
4,3
4,9
5,5
6,1
6,7
7,3
7,9
8,5
9,1
9,8
10,4
13,4
11,0
11,6
12,2
12,8
14,6
14,0
15,2
18,3
17,1
16,5
17,7
18,9
19,5
20,1
20,7
21,91,21,8 1,2 0,6 0 0,6 3,72,41,8 3.0 4,3 4,9 5,5 6,1 11,66,7 7,3 7,9 8,5 10,49,1 9,8 11,0 14,012,812,2 13,4 14,6 15,2 1,8 16,5 17,1 17,7 18,3 18,9 19,5 20,1
1,21,8 1,2 0,6 0 0,6 3,72,41,8 3,0 4,3 4,9 5,5 6,1 11,66,7 7,3 7,9 8,5 10,49,1 9,8 11,0 14,012,812,2 13,4 14,6 15,2 15,8 16,5 17,1 17,7 18,3 18,9 19,5 20,1
0°
10°
20°
30°
40°
50°
60°
69°
RETRACTED RETRACTED EXTENDED EXTENDED 4,6 m
15,8
0,6
1,2
1,8
2,4
3,0
3,7
4,3
4,9
5,5
6,1
6,7
7,3
7,9
8,5
9,1
9,8
10,4
13,4
11,0
11,6
12,2
12,8
14,6
14,0
15,2
18,3
17,1
16,5
17,7
18,9
19,5
20,1
20,7
21,3
21,9
21,3
Operating radius in meters from axis of rotation
Boo
m a
nd e
xten
sion
leng
th in
met
ers
Hei
ght
from
the
gro
und
in m
eter
s
14
DIN/ISO load chart
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
YB5515 (three-section boom)
YB5515 3-SECTION BOOM LOAD RATING and RANGE DIAGRAM
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OFINSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors a�ecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart.
MA
IN B
OO
MJIB
ON RUBBER (kg)ON OUTRIGGERS (kg)RADIUS(m)
47503840
1750
13101230
14501600
21901950
25703120
14101330
11901080
950870
10801010
1140
2080
16401850
301026602350
3460
1500
26502310
220190
260240
1370
530
350320290
450400
750620
9201130
20901700
400350
470430
1940
830
590
500550
740660
1110950
13201610
1260
F/R 360˚ F/R 360˚
48603600
4,34,64,95,56,16,77,37,98,59,19,810,411,011,412,212,813,414,014,9
1,82,43,03,7
940 750 14028016,0
671059005540490043703920
671059005530
3270299027502320
13 61011 88010 1208440
13 61011 88010 1208440
77106120
77106620
48503950
BOOM
(deg)ANGLE
MAIN
60
40
15
0
3035
4550
-
JIB STRUCTURAL
55
2520
5 -10 -
6965
-
-
--
--
15˚0˚ 30˚
CAPACITIES (kg)
1020
880
980940
1430
11801090
1290
930910
17701590
1270
950
910
11801090
1950
15401380
1720
10401000
920930
27202270
880860840
1070
950910
1000
12701160
4) Ratings on outrigggers are with outriggers fully extended.
5) Ratings on rubber depend on tire capacity, condition of tires and proper inflation pressure (8,3 bar). Loads on rubber may be transported at a maximum speed of 1,4 km/h on a smooth hard level surface with boom retracted to the shortest length possible and centered over front.
6) For operating radius not shown, use load rating of next larger radius.
7) The maximum combined total boom and deck load is 7260 kg. The maximum deck load only is 9070 kg.
8) Do not induce any external side loads to boom or jib.
1302539YB
15˚
30˚
15˚
30˚
FRONT REAR
SIDE
SIDE
0 - 13 610 kg4-PART
0 - 3400 kg1-PART
RIGGING CHART
WIRE ROPE: 13 mm diameterMin. breaking strength 128,4 kN.
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
100 kg
50 kg
0 kg
320 kg
N/A
50 kg
N/A
0 kg
Grove YB5515 Dual Fuel 15
DIN/ISO load chart
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
YB5515 (four-section boom)
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 80% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors a�ecting stability.Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity, condition of tires andproper inflation pressure (8,3 bar).Loads on rubber may be transported at a maximum speedof 1,4 km/h on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 7260 kg.The maximum deck load only is 9070 kg.
8) Do not induce any external sideloads to boom or jib.
NOTES: JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
0 - 13 610 kg4-PART
0 - 3400 kg1-PART
RIGGING CHART
WIRE ROPE: 13 mm diameter
Min. breaking strength 128,4 kN.
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
100 kg
50 kg
0 kg
320 kg
N/A
50 kg
N/A
0 kg
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
ON RUBBER (kg)ON OUTRIGGERS (kg)
MA
IN B
OO
MJIB
6710
RADIUS(m)
59005540490043703920
17,7
67105900554044503600
1800
12701150
14401600
23402060
26703050
11701090
950870780
- -
810700550
950880
1020
1790
14101590
282024002050
3320
1290
32702990
24002140
-
1209050
170150
1310
470
270230190
400340
650560
8201030
19601620
-
280230150
360320
1720
770
500
400450
670580
990870
11501380
26702160
1020
F/R 360o F/R 360o
19,4 - - --
ON RUBBER (kg)ON OUTRIGGERS (kg)
3760
RADIUS(m)
37203680361035503500
37603720368036103550
1950
12701180
14401660
26202230
30203500
13601260
1040900800650 500
820740640
970890
1070
2120
16901910
318027302350
3460
1550
35203240
33202670
0
1309050
200160
1530
630
370320250
530450
890750
10601280
24201960
110
280240190
350310
2060
910
540
400480
770640
12501080
14701720
30002530
1150
F/R 360o F/R 360o
480 350 020
4TH EXTENDEDBOOM
(deg)ANGLE
MAIN
4TH RETRACTED
60
40
15
0
3035
4550
JIB STRUCTURAL CAPACITIES (kg)
55
2520
510
13 61011 88010 1208440
13 61011 88010 1208440
77106120
7710612048903390
48603950
-503048504200
-503048504200
-5030
-503048504200
48504200
6965
4TH RETRACTED
4TH EXTENDED
15o0o 30o 0o 15o 30o
1020
880
-
980940
1430
11801090
1290
930910
--
17701590
1270
950
910
11801090
1950
15401380
1720
10401000
920930
23502250
880
-
-
860840
1070
950910
1000
--
--
12701160
4,34,64,95,56,16,77,37,98,59,19,810,411,011,412,212,813,414,014,9
1,82,43,03,7
16,017,719,4
4,34,64,95,56,16,77,37,98,59,19,810,411,011,412,212,813,414,014,9
1,82,43,03,7
16,0
1020
880
-
980940
1430
11801090
1290
930910
--
17701590
1270
950
910
11801090
1950
15401380
1720
10401000
920930
27202270
880
-
-
860840
1070
950910
1000
--
--
12701160
16
Symbols glossary
Drive
RotationElectrical system
Suspension
Fuel tank capacity
Tires
Engine
Brakes
Outrigger controls
Axles Outriggers
Transmission
Frame
Steering
Lights
Boom elevation
Cab
Swing
Hydraulic system
Hoist
Boom nose
Radius
Boom extension
Boom length
Grade
Gear
Boom
Counterweight
Speed
Oil
Extension
HookblockH
Heavy duty jib
Grove YB5515 Dual Fuel17
Notes
18
Notes
Grove YB5515 Dual Fuel 19
Notes
©2013 ManitowocForm No. YB5515 Dual Fuel PGPart No. 13-002 /2M/0113 www.manitowoccranes.com
This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.
Regional offices
ChinaShanghai, China Tel: +86 21 6457 0066Fax: +86 21 6457 4955
Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 4040
Europe, Middle East, Africa Ecully, France Tel: +33 (0)4 72 18 20 20 Fax: +33 (0)4 72 18 20 00
Americas Manitowoc, Wisconsin, USA Tel: +1 920 684 6621 Fax: +1 920 683 6277
Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 4062
Regional headquarters
Manitowoc Cranes
ChinaBeijingChengduGuangzhouXian
Greater Asia-PacificAustraliaBrisbaneMelbourneSydneyIndiaChennaiDelhiHyderabadPuneKoreaSeoulPhilippinesMakati CitySingapore
FactoriesBrazilPasso FundoChinaTaiAnZhangjiagangFranceCharlieuMoulinsGermanyWilhelmshavenIndiaPuneItalyNiella TanaroPortugalBaltarFânzeresSlovakiaSarisUSAManitowoc Port WashingtonShady Grove
AmericasBrazilAlphavilleMexicoMonterreyChileSantiago
Europe, Middle East, AfricaCzech RepublicNetvoriceFranceBaudemontCergyDecinesGermanyLangenfeldHungaryBudapestItalyLainateNetherlandsBredaPolandWarsawPortugalBaltarRussiaMoscowSouth AfricaJohannesburgU.A.E.DubaiU.K.Buckingham