Upload
ajayi-olatunde-rocc
View
217
Download
0
Embed Size (px)
Citation preview
8/3/2019 Group Two Materials' Presentation
1/12
8/3/2019 Group Two Materials' Presentation
2/12
BRIEF HISTORY OF HELICOPTERS
The idea of a helicopter is bionic in origin,
i.e. it was derived from an attempt to adapt anatural phenomena-in this case, the whirling,bifurcated fruit of the maple tree-to a
mechanical design. Leonardo Da Vinci sketched a flying
machine that may have been based on thewhirlgig during the 15th century.
In the early 19th century, Sir George Cayleydrew a twin-rotor aircraft.
In the early 20th century, Paul Cornu
managed to lift himself off the ground for a
8/3/2019 Group Two Materials' Presentation
3/12
For a long time no one could devise anengine that could generate enough verticalthrust to lift both the helicopter and anysignificant load off the ground.
The first helicopter was built by Igor Sikorskyin 1909 but neither the prototype not itssuccessor in 1910 succeeded.
During World War I, Theodore von Karmanconstructed a helicopter that was able hoverfor extended periods.
Years later, Juan de la Cierva developed amachine called an autogirowhich became
popular in the 1920s and 30s. The helicopter was eventually perfected by
Igor Sikorsky with advances in aerodynamictheory and building materials. It was used
extensively during World War II.
8/3/2019 Group Two Materials' Presentation
4/12
A TYPICAL HELICOPTER
A typical helicopter has four(4)
compartments; The rotor blades
The fuselage
The tail plane The landing gear
A helicopters power comes from either a
piston engine or a gas turbine (recently,the latter has predominated), whichmoves the rotor shaft causing the rotor to
turn. The rotor achieves lift by pushing the
8/3/2019 Group Two Materials' Presentation
5/12
MATERIALS USED IN THE
PRODUCTION OF A HELICOPTER
In general, the airframe i.e. fundamentalstructure of a helicopter can be made ofeither metal or organic compositematerials or a combination of the two.
Higher performance requirements willrequire higher strength-to-weight ratiooften epoxy reinforced with glass, aramid(a strong flexible nylon fiber) or carbonfibre.
Tubular and sheet metal substructuresare usually made of aluminum, though
stainless steel or titanium is sometimes
8/3/2019 Group Two Materials' Presentation
6/12
HELICOPTER ROTOR BLADES
They are usually made of fibre-reinforcedplastics (FRPs) which may be adhesivelybonded with an external sheet metal layer toprotect the edges. The composite can beglass or carbon FRPs
The matrix has the following characteristics; They allow external stresses to be conveyed
and distributed to them.
They are ductile and relatively soft.
With high plasticity, they prevent crackpropagation between fibres.
They are light and readily available at low
cost.
8/3/2019 Group Two Materials' Presentation
7/12
THE FUSELAGECanopies, windscreens and passengercompartment windows are generally made of
polycarbonate sheet. They are made by layingthe sheet over a mould, heating it and forming itwith air pressure in a process called free-blowingin which no tool ever touches the part. Other
materials used are polystyrene, fibreglass andcarbon fibre.
These materials have the followingcharacteristics;
Polystyrene is very inexpensive and serve as verygood protective shells for little helicopters.
Polycarbonate is light and inexpensive but coldweather makes them very brittle.
Fibreglass is heavier and more expensive butstron er.
8/3/2019 Group Two Materials' Presentation
8/12
THE TAIL PLANE
This carries the anti-torque rotor or tail rotor;which is a smaller rotor mounted so that it
rotates vertical or near-vertically in order tocounter the torque effect created by the mainrotor. They are majorly made from carbonfibre and glass fibre but for smallerhelicopters, aluminium and plastics are used.
The characteristics of the materials are;
They are strong and light.
They handle heat and cold properly. They absorb vibration.
Carbon fibre can be moulded to be superstiff in one direction and flexible in anotherdirection.
8/3/2019 Group Two Materials' Presentation
9/12
THE LANDING GEAR
This is an area of helicopter design that
continues to elude the compositescommunity. This is due to the fact thatstructural elements with concentratedloads and conservative design practice
has traditionally dictated metals for itsuse.
But this may change if the on-going
research to design and fabricatelightweight and durable composite landinggears is successful.
8/3/2019 Group Two Materials' Presentation
10/12
THE LANDING GEAR
8/3/2019 Group Two Materials' Presentation
11/12
THE FUTURE HOTELICOPTERS
8/3/2019 Group Two Materials' Presentation
12/12
THE FUTURE: HOTELICOPTERS
The hotelicopter is modelled on an old soviet Mil
V-12 helicopter and features 18 luxuriously-appointed soundproof rooms complete withqueen sized beds, wireless internet and roomservice as expected from a 5-star hotel.