Greddy Turbo Timer Installation Manual

8/9/2019 Greddy Turbo Timer Installation Manual

http://slidepdf.com/reader/full/greddy-turbo-timer-installation-manual 1/8

Greddy Turbo Timer Install

Last updated: April 2, 2001

TURBO TIMER MANUAL

How to wire the Turbo Timer w/ the Turbo Timer Harness

How to wire the Turbo Timer w/o the Turbo Timer Harness

dy Turbo Timer Install http://www.fd3s.net/greddy_turbo_timer_ma

17-Oct-10



On the power harness, cut off the large 3-pin connector.1.

Tap or solder the cut lines of the power harness to the appropriate lines as shown below.2.

Be sure to ground the black wire to a good ground source.3.

Important: The Turbo Timer will not function properly if there is a bad ground connection. If grounding to the body, makesure to remove the paint for the best ground.

Optional set-ups

Optional: Connect for Optional Parking Brake WarningThis feature notifies the driver with a "beep" if the key is removed without the parking brake engaged.


17-Oct-10



Remove the cover for the parking brake. Look for the parking brake switch wire.1.

If there is only one wire from the switch, check to see: If the wire has: 0V when parking brake is ON 12V when

parking brake is OFF

If there are two wires from the switch, look for the wire that has:

0V when parking brake is ON

12V when parking brake is OFF

2.

Route the "BROWN" wire from the Safety Feature Harness through the center console to the parking brake switch.3.

Tap the "BROWN" wire to the wire from Step 2.4.

Reinstall the parking brake cover.5.

Optional: Connect for Speedometer Signal FeatureThis feature will shut the engine off if the vehicle starts to move during "turbo-timing."

Connect the "PURPLE" wire to the speedometer signal wire from the ECU.1.

Please refer to the factory service manual of the vehicle for the proper signal wire.2.

This feature should only be attempted by a skilled technician.3.


17-Oct-10



Important: GReddy Performance Products, Inc. is not responsible for any damage caused by improper installation of the

GReddy Turbo Timer.

IMPORTANT:Please do not attempt to hold down the POWER switch button while the turbo timer is turned off. This may cause the

Turbo Timer to malfunction.

Basic Operation

Start the engine

Music starts

2 seconds later

After 1 minute

During vehicle operation

Engine shuts down

Test: Parking Brake Safety Feature


17-Oct-10





Caution: When checking this feature

be sure that there are no objects

directly in front of or behind the

vehicle.

1. Apply the foot brake and release the

parking brake.

2. Repeat steps 1-4 of the basic

operation check procedure. It should

count down and snd flash alternately

with a "beeping" sound.

3. Then put the vehicle in gear, release

the foot brake, and move the vehicle.

The engine should then shut down.

This completes the operation check

If the Turbo Timer does not operate properly, first check all of the wire

connections, contact the Authorized

GReddy Dealer you purchased the

turbo timer from for assistance.

How to change the preset time

By pressing the time switch, you can

change the time setting.

When the Program Number is

displayed.

When the Time is diplayed.

* If you tap the time switch button, the

time will increase, by 10 seconds.

* If you hold down the time switch

button, the time will increase by l

minute.

How to program the preset time


17-Oct-10



By holding down the select switch,

you can save a desired time for both

P-1 and/or P-2

1. Set to the desired Preset time setting

P-1 or P-2

2. Set the time to desired time by

joggling the Time switch button.

3. Hold down the SELECT switch

button for 2-3 seconds, until you hear

a "beep." The desired time will now be

saved in the turbo timer's memory until

the battery is disconnected.

How to select the preset time

By pressing the select switch, you can

select the 2 preset time settings

Preset Time Setting:

P-1 > 1 minute

P-2 > 3 minute

* To switch to a desired preset timesetting, press select switch

* When the select switch is pressed

while the digital display is showing the

time. The turbo timer will then display

either P-1 or P-2.




either P-1 or P-2.




either P-1 or P-2.

How to turn the sound off


17-Oct-10



By pressing and holding down the

power switch while the turbo timer is

ON, you can turn the sound ON and

OFF.

1. Turn the POWER on.

2. Hold the POWER switch button for

2-3 seconds

3. Then the Turbo Timer will make a

single beep, indicating that the Turbo

Timer's sound mode is either turned on

or off


Documents

Greddy Turbo Timer Installation Manual