PHOTO OF PRODUCT

MODEL# GPM630

PASTA MAKERHOMEMADE PASTA

www.gourmia.com

© 2016 Gourmia

www.Gourmia.com

The Steelstone Group

Brooklyn, NY

All rights reserved. No portion of this manual may be reproduced by any means whatsoever

without written permission from The Steelstone Group, except for the inclusion of quotations in a

media review.

Although every precaution has been taken in the preparation of this manual, The Steelstone

Group assumes no responsibility for errors or omissions. Nor is any liability assumed for damages

resulting from the use of the information contained herein. Although every e�ort has been made

to ensure that the information contained in this manual is complete and accurate, The Steelstone

Group is not engaged in rendering professional advice or services to the individual consumer;

further, The Steelstone Group shall not be held responsible for any loss or damage allegedly

arising from any information or suggestion in this manual.

10 9 8 7 6 5 4 3 2 1

Printed in China

Welcome to Indulgence of Homemade Pasta Maker from Gourmia!

Fresh, delicious homemade pasta has never been easier than it is with the Gourmia

Pasta Maker. Everything is automated—from blending to kneading to extracting—so

you have �avorful pasta in just minutes with almost no work. Add di�erent �avors like

herbs and vegetables and use any of the 9 di�erent pasta shaping discs to make a

unique meal every time. Plus, the Gourmia Pasta Maker disassembles easily, making

clean-up a breeze.

The following pages of this manual o�er full and complete instructions for

all the functions and features of your Pasta Maker. Inside these pages, you’ll �nd

information on and instructions for assembly, operating, cleaning and maintenance

of your Pasta Maker. Please read all safety instructions and complete directions

carefully for safe usage at all times.

Thank you for your purchase! We hope you will enjoy all the innovative products

brought to you by our family at Gourmia.

TABLE OF CONTENTSSAFETY FIRST p. 6

FEATURES & PARTS p. 8

ASSEMBLY & USAGE p. 10

CLEANING & TROUBLESHOOTING p. 12

WARRANTY & SERVICE p. 14

SAFE

TY F

IRST

SAFETY FIRST

IMPORTANT SAFEGUARDSWhen operating this electric appliance, basic safety instructions should always be followed. Refer to the following for these instructions.1. Before connecting the appliance to the mains, check whether the type of supply and

the mains voltage corresponds with the appliance.2. Always switch OFF and pull the plug out of the socket before you clean the appliance

supply, never pull the plug out using the power cord, always pull directly on the plug. Never carry the unit by its power cord.

3. Indoor use only. Never immerse the device in water and do not expose the device to

socket and only then remove the device from the water. Afterwards have the unit examined by an authorized service center before you use it again.

5. Set up and store the appliance and its attachments out of reach of children. 6. Do not leave the appliance unattended while it is on. 7. Always ensure that the device is safely set up before you start to use it. 8. Keep your hair, clothing and jewelry away from the rotating parts.9. Check unit and its components regularly for damages. Do not use the appliance if it

is damaged in any way. Have it immediately repaired at an authorized service center. Do not ever try to repair the unit yourself. There is danger of electrical shock.

10. If the supply cord is damaged, it must be replaced by the manufacturer, its service

11. No claims under the warranty or liability for damages will be accepted if they result

12. from improper or incorrect use .

CAUTION! Handle the attachments with care.

13. Do not try to open the housing yourself. Do not introduce any kind of objects into the housing.14. Do not operate the unit continuously for more than 20 minutes. Allow the unit to cool completely before using again. 15. The manufacturer does not recommend the use of accessory attachments. Use of accessory attachments may cause injuries.16. Position the appliance as close to the outlet as possible to prevent injury due to tripping over cord.17. Do not place on or near a hot gas or electric burner, nor in a heated oven.18. A short power supply cord is provided to reduce the risk resulting from becoming entangled or tripping over a long cord.19. Longer detachable power-supply cord or extension cord are available and may be

used if care is exercised in their use. Exception: An extension cord or longer detachable cord is not recommended for use with this appliance.

20. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.

21. Children shall not play with the appliance.22. If a long detachable power-supply cord or extension cord is used: 1)The marked

electrical rating of the cord or extension cord should be at least as great as the

6 7

FOR HOUSEHOLD USE ONLYElectrical 3-conductor Cord Set: Appliance is equipped with a 3-conductor cord set that has a 3 prong grounding-type plug. It should be properly connected to a grounding-type

a 3-grounding outlet unit, and as such, the grounding prong should never be removed. If needed, purchase a 2-prong adapter and ground it to the outlet.

Do not use an adapter unless you are

for assistance.

electrical rating of the appliance; 2) If the appliance is of the grounded type, the extension cord should be a grounding 3-wire cord; and 3)The longer cord should be arranged so that it does not drape over the counter top or table top where it can be pulled on by children or tripped over unintentionally.

23. Do not let cord hang over edge of table or counter or touch hot surface.

25. Make sure that the cord does not pass over hot or sharp edged objects.26. Do not allow the main lead to become kinked or trapped. The cable should be laid so

that there will not be any risk of anyone pulling it inadvertently or tripping over it.

28. Connect the device to an earthed socket.29. This item may contain chemicals that may cause cancer or birth defects.

27.

24.

SAVE THESE INSTRUCTIONS

FEATURES & PARTS

FEATURES & PARTS FEATURES & PARTS

8 9

D

D

C

C

L

M

J

J

K

K

B

B

E

E

F

F

G

G

H

H

I

I

A

A. Control Panel G. Front PanelB. Upper Cover H. Pasta Shaping DiscC. Water Adding Dish I. KnobD. Plastic Mixing Bowl J. Pasta Shaping Disc DrawerE. White Plastic Panel K. Spiral RodF. Open Button L. Machine Body

M. Watering Adding CaseN. Flour CupO. Measuring CupP. Thru-hole PinQ. Small Water Cup

M

N

N O P QA. UdonB. VermicelliC. MacaroniD. RotiniE. Sausage/Ravioli AdapterF. Angel hairG. Lasagna

H. LinguineI. SpaghettiJ. PenneK. Sausage CoreL. BucatiniM. Dumpling/Ravioli CoreN. Dumpling/Ravioli Press

A

CONTROL PANEL

PASTA SHAPING DISCS

L

ASSEMBLY & USAGE

ASSEMBLY & USAGE ASSEMBLY & USAGE

10 11

ASSEMBLY1. Insert the plastic mixing bowl into the groove of the base with the large round opening facing out and the square opening on top.2. Insert the spiral rod through the front opening of the mixing bowl into the opening in the back of the base. The rod should securely attach to the small hole on the interior of the base.3. Secure the white plastic panel to the front of the base by securing it through the attached screws. 4. Choose the plastic pasta shaping disc you want to use and insert it into the back of the metallic front panel. Make sure the tab on the plastic shaping disc is inserted into the groove on the front panel.5. Attach the metallic panel to the screws on the front of the machine and push the

the knobs on.6. Place square plastic cover on top of the machine and push down to lock it in place.

USEMaking Pasta

perfect noodles.

Notes:

side of a butter knife. • Use the included water measuring cup to measure the liquids.

• As pasta begins to be extruded, coat with additional flour to prevent sticking.• Use tray instead of bowl to separate and allow to dry.

Note: The first bits might be stringy, they get smoother as the machine runs.Stop and extrude again if machine gets too fast.

Making Pasta Automatically:1. Assemble the machine as described above, making sure to choose the correct shaping disc for the type of pasta you want to make.2. Open the top of the machine.

place.4. Measure the water and set aside.5. Place the water-adding dish in the grooved area on the top cover. You know it

6. Put a bowl under the extruding holes in the front of the machine.7. Plug the machine in and the display turns on.8. Press the Auto button. The spiral rod begins turning and the timer starts for the indicated amount of time.9. As soon as the mixing process begins, add the water into the water-adding

pasta into the bowl.

machine stops.

Making Pasta Manually:1. Assemble the machine as described above, making sure to choose the correct shaping disc for the type of pasta you want to make.2. Open the top of the machine.

place.4. Measure the water and set aside.5. Place the water-adding dish in the grooved area on the top cover. You know it

6. Plug the machine in and the display turns on.7. Press the Mix button. The display blinks a few times, showing the default time of 4 minutes. You can increase or decrease the amount of mixing time by pressing the + and – buttons while the time is blinking.8. After a couple of seconds, the display stops blinking, the spiral rod begins turning and the timer starts for the indicated amount of time.9. As soon as the mixing process begins, add the water into the water-adding

11. Put a bowl under the extruding holes in the front of the machine. Press the Extrude button. The pasta begins coming out of the machine into the bowl.

machine stops.

Flour using included Cup

1 cup 270 g /9.52 oz

1 cup +3 tbsp

1 egg plus enough water to equal126 mL, combined

126 mL

1.5 cups 450 g /15.87 oz.

1.5 cups

166 mL

2 cups 540 g /19.04 oz.

2 cups

208 mL

AP Flour Using

Included Cup

OR Flour by Weight

OR Water &

Egg

OR Vegetable

Juice

Water using Included

Cup

126mL/.525 C (American)

/4.26 � oz

166 mL.7 C (American)

/5.61 � oz

208 mL.87 C (American)

/7.03 � oz

OR Water ByVolume

NOTE: Cup included is not equivalent to 1 cup in an american standard units

1 egg plus enough water to equal166 mL, combined

1 egg plus enough water to equal208 mL, combined

USAGE & CLEANING TROUBLESHOOTING

CLEANING & TROUBLESHOOTING

1312

ASSEMBLY1. Insert the plastic mixing bowl into the groove of the base with the large round opening facing out and the square opening on top.2. Insert the spiral rod through the front opening of the mixing bowl into the opening in the back of the base. The rod should securely attach to the small hole on the interior of the base.3. Secure the white plastic panel to the front of the base by securing it through the attached screws. 4. Choose the plastic pasta shaping disc you want to use and insert it into the back of the metallic front panel. Make sure the tab on the plastic shaping disc is inserted into the groove on the front panel.5. Attach the metallic panel to the screws on the front of the machine and push the panel in so it is �ush against the machine. Secure the panel by tightly screwing the knobs on.6. Place square plastic cover on top of the machine and push down to lock it in place.

USEMaking PastaRefer to the following chart for the correct amounts of �our and liquid to make the perfect noodles.

Notes: • When measuring �our with a measuring cup, �atten the scoop with the �at side of a butter knife. • Use the included water measuring cup to measure the liquids.• When making egg pasta, add the egg to the measuring cup and then add water until the required liquid amount is reached.• To make the extrusion process smoother, add a teaspoon of oil to the liquid before you add it to the �our.

Making Pasta Automatically:1. Assemble the machine as described above, making sure to choose the correct shaping disc for the type of pasta you want to make.2. Open the top of the machine.3. Measure the �our and add to the mixing bowl. Replace the cover and lock in place.4. Measure the water and set aside.5. Place the water-adding dish in the grooved area on the top cover. You know it is in correctly when it �ts snugly in the area.6. Put a bowl under the extruding holes in the front of the machine.7. Plug the machine in and the display turns on.8. Press the Auto button. The spiral rod begins turning and the timer starts for the indicated amount of time.9. As soon as the mixing process begins, add the water into the water-adding dish. The water is slowly added and mixed into the �our to make the dough.10. When the mixing is �nished, the machine automatically begins extruding the pasta into the bowl.11. When the machine �nishes extracting all of the dough, 4 beeps sound and the machine stops.12. When �nished, unplug the machine.

Making Pasta Manually:1. Assemble the machine as described above, making sure to choose the correct shaping disc for the type of pasta you want to make.2. Open the top of the machine.3. Measure the �our and add to the mixing bowl. Replace the cover and lock in place.4. Measure the water and set aside.5. Place the water-adding dish in the grooved area on the top cover. You know it is in correctly when it �ts snugly in the area.6. Plug the machine in and the display turns on.7. Press the Mix button. The display blinks a few times, showing the default time of 4 minutes. You can increase or decrease the amount of mixing time by pressing the + and – buttons while the time is blinking.8. After a couple of seconds, the display stops blinking, the spiral rod begins turning and the timer starts for the indicated amount of time.9. As soon as the mixing process begins, add the water into the water-adding dish. The water is slowly added and mixed into the �our to make the dough.10. When the mixing is �nished, the machine beeps 3 times.11. Put a bowl under the extruding holes in the front of the machine. Press the Extrude button. The pasta begins coming out of the machine into the bowl. 12. When the machine �nishes extracting all of the dough, 4 beeps sound and the machine stops.13. When �nished, unplug the machine.

USE continued...Making Egg NoodlesTo make egg noodles, follow either of the two noodle making processes above with one exception. Instead of adding the liquid to the water-adding cup, you need to mix the egg-water combination well and then pour it directly through the small holes in the plastic cover on top of the machine.

Making Sausage1. Assemble the machine as described above, making sure to choose the Sausage/Ravioli Adapter parts and the sausage core in place of the pasta shaping disc. Insert the sausage core into the shell and secure the shell to the spiral rod with the sausage core facing out. Then attach the metallic front panel.2. Add the meat and other sausage ingredients to the bowl and secure the lid to the top of the machine.3. Plug the machine in and press Mix. While the time is still blinking, press the – button to reduce the mixing time to 3 minutes.4. When the mixing is �nished, put the sausage casing over the sausage core, leaving enough to be able to tie the casing closed.5. Hold the sausage casing in place on the sausage core and press Extrude. The sausage mixture begins �lling up the sausage casing.6. Once the sausage casing is �lled, press Cancel to stop the extruding process.7. Remove the sausage casing and tie it closed.8. Repeat with more casings.9. When �nished, unplug the machine.

CLEANING• Unplug the machine before cleaning.• The mixing bowl, spiral rod, upper cover, panels, pasta shaping discs, and knobs should all be washed with warm, soapy water.• The exterior of the machine should be wiped down with a soft, damp cloth.• Dry all parts thoroughly before storing or using.• The machine should not be submerged in water or any other �uid.• Store the pasta machine in a cool, dry place.

The machine does not turn on Check that the top cover is

closed tightly Check that the knobs in the front

of the machine are securely

fastened. The dough cannot be extruded The consistency of the dough is

not right. If it seems too wet, add

more �our; if it’s too dry, add

more water. The equipment cannot be

cleaned easily Wait for the dough to dry for

about 30 minutes and then wash

the equipment.

WARRANTY & SERVICE

1514

WARRANTY & SERVICE

This Limited Warranty is for one full year from the date of purchase. It is

applicable to the original purchaser only and is not transferable to a third party

user. Repair or replacement of defective parts is solely at the seller’s discretion.

In the event that repair isn’t possible, the seller will replace the product/part. If

the cash value of the product or component returned.

Product defects not covered under the Warranty provisions include normal wear

and damage incurred from use or accidental negligence, misuse of instruction

is not liable for any incidental or consequential damages incurred by such

circumstances.

For Customer Service or Questions, Please call: 888-552-0033

www.gourmia.com

DISPOSAL

DISPOSAL OF THE DEVICEPROTECTION OF THE ENVIRONMENT At the end of the life of your product, it should go to a specially adapted waste-recycling center.

ENVIRONMENT PROTECTION FIRST

1. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be handed over to the applicable. Collection point for the recycling of electrical and electronic equipment.2. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product .For more detailed information about the recycling of this product, Please contact your local council o�ce or your household waste disposal service.