Gettingstarted WinCC

  • View
    216

  • Download
    0

Embed Size (px)

Text of Gettingstarted WinCC

  • 8/4/2019 Gettingstarted WinCC

    1/252

    SIMATIC WinCC V7.0 Getting started ______________

    ______________

    ______________

    ______________

    ______________

    ____________________________

    ______________

    ______________

    Getting started 1Welcome 2Icons 3Creating a project 4Configure communication 5Configuring the ProcessScreens 6Archiving and displayingvalues 7Outputting values from theprocess archive 8Configuring messages 9

    SIMATICWinCC V7.0Getting started

    Printout of the Online Help

    04/2008A5E02211557-01

  • 8/4/2019 Gettingstarted WinCC

    2/252

    Safety Guidelinesafety Guidelines

    This manual contains notices you have to observe in order to ensure your personal safety, as well as to preventdamage to property. The notices referring to your personal safety are highlighted in the manual by a safety alertsymbol, notices referring only to property damage have no safety alert symbol. These notices shown below aregraded according to the degree of danger.

    DANGERindicates that death or severe personal injury will result if proper precautions are not taken.

    WARNINGindicates that death or severe personal injury may result if proper precautions are not taken.

    CAUTIONwith a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

    CAUTIONwithout a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

    NOTICEindicates that an unintended result or situation can occur if the corresponding information is not taken intoaccount.

    If more than one degree of danger is present, the warning notice representing the highest degree of danger willbe used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating toproperty damage.

    Qualified PersonnelThe device/system may only be set up and used in conjunction with this documentation. Commissioning andoperation of a device/system may only be performed by qualified personnel. Within the context of the safety notesin this documentation qualified persons are defined as persons who are authorized to commission, ground andlabel devices, systems and circuits in accordance with established safety practices and standards.

    Prescribed UsageNote the following:

    WARNINGThis device may only be used for the applications described in the catalog or the technical description and onlyin connection with devices or components from other manufacturers which have been approved orrecommended by Siemens. Correct, reliable operation of the product requires proper transport, storage,positioning and assembly as well as careful operation and maintenance.

    TrademarksAll names identified by are registered trademarks of the Siemens AG. The remaining trademarks in thispublication may be trademarks whose use by third parties for their own purposes could violate the rights of theowner.

    Disclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and softwaredescribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, theinformation in this publication is reviewed regularly and any necessary corrections are included in subsequenteditions.

    Siemens AGIndustry SectorPostfach 48 4890327 NRNBERGGERMANY

    Printout of the Online Help 05/2008

    Copyright Siemens AG 2008.Technical data subject to change

  • 8/4/2019 Gettingstarted WinCC

    3/252

    Getting started04/2008, Printout of the Online Help 3

    Table of contents1 Getting started ............................................................................................................. .............................. 72 Welcome.................................................................................................................................................... 93 Icons........................................................................................................................................................ 114 Creating a project .......................................................................................................... .......................... 13

    4.1 Creating a project.........................................................................................................................13

    4.2 Working with WinCC....................................................................................................................134.3 Creating the "Quick_Start" project ...............................................................................................15

    5 Configure communication...................................... .................................................................................. 195.1 Configure communication ............................................................................................................19

    5.2 Check the channels and connections in WinCC..........................................................................20

    5.3 Tags in WinCC.............................................................................................................................21

    5.4 Adding a Channel ........................................................................................................................22

    5.5 Creating connections ...................................................................................................................25

    5.6 Creating tag group .......................................................................................................................28

    5.7 Creating a process tag.................................................................................................................30

    5.8 Scaling process tags in WinCC....................................................................................................36

    5.9 Creating Internal Tags .................................................................................................................39

    6 Configuring the Process Screens ............................................................................................................ 436.1 Configuring the Process Screens ................................................................................................43

    6.2 The Graphics System ..................................................................................................................44

    6.3 Creating process screens ............................................................................................................45

    6.4 Editing Process Screens..............................................................................................................476.4.1 Editing Process Screens..............................................................................................................47

    6.4.2 Inserting graphic objects from the library.....................................................................................486.4.3 Inserting "Static text"....................................................................................................................556.4.4 Editing the process screen "SAMPLE.pdl" ..................................................................................57

    6.5 Using customized menus and toolbars........................................................................................596.5.1 Using customized menus and toolbars........................................................................................596.5.2 Creating procedures for customized menus and toolbars ...........................................................606.5.3 Creating a customized menu for screen changes .......................................................................666.5.4 Creating a customized toolbar to exit Runtime ............................................................................71

  • 8/4/2019 Gettingstarted WinCC

    4/252

    Table of contents

    Getting started4 04/2008, Printout of the Online Help

    6.6 Process picture dynamics ........................................................................................................... 776.6.1 Process picture dynamics ........................................................................................................... 776.6.2 Making the fill level indicator dynamic......................................................................................... 78

    6.6.3 Inserting an I/O Field and Making it Dynamic ............................................................................. 826.7 Defining the Runtime Properties ................................................................................................. 87

    6.8 Activating the project................................................................................................................... 91

    6.9 Test project ................................................................................................................................. 93

    6.10 Deactivating a project.................................................................................................................. 96

    7 Archiving and displaying values............................................................................................. .................. 977.1 Archiving and displaying values.................................................................................................. 97

    7.2 The archive system ..................................................................................................................... 97

    7.3 Starting Tag Logging.......................................................................