Fully Integrated 24” MasterCool - us.mieleusa.com · the cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surrounding cabinets

Fully Integrated 24” MasterCool

K 2601 Vi / K 2611 Vi

F 2601 Vi / F 2611 Vi

KWT 2601 Vi / KWT 2611 Vi

KWT 2661 ViS / KWT 2671 ViS

8mieleusa.comSpecification Sheets TRS 05202019 Please note: This information is subject to change

Shown: KWT 2611 ViS


Please note the following:• This specification sheet is for a single built-in unit.• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specification sheet. *If design calls for a partition less than 6 5/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of the Heating Mat/Merge Kit.

SPECIFICATIONS

Overall Unit Dimensions 233/4” (604 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Depth does not include door panel]

Niche

Minimum Cabinet Niche Opening 24” (610 mm) W* x 84” - 853/16” (2134 - 2164 mm) H x 243/4” (629 mm) D

Electrical K 26x1 Vi KWT 26x1 Vi F 26x1 Vi

Electrical Requirements110V / 120V, 60Hz, 15 Amps

In the case of side-by-side installations, a separate outlet must be used for each appliance.

Power Cord NEMA 5-15 plug, 5 ft (1.52 m)

Plumbing K 26x1 Vi KWT 26x1 Vi F 26x1 Vi

Water Supply Requirements -

Connect to a cold water supply only. Do not connect to a low-mineral or a reverse osmosis system. Must be connected to a shut-off valve. The water shut-off valve must be accessible after installation. The water pressure must be between 29 psi (2 bar) and 116 psi (8 bar). If the pressure is higher than 120 psi (8.3 bar), a pressure reducing valve must be installed.

Water Connection Line -Standard 1/4” O.D flexible water line. The maximum outer diameter of the water pipe (without fittings): 3/8” (10 mm). Water line is not included.

Shipping K 26x1 Vi KWT 26x1 Vi F 26x1 Vi

Shipping Weight 346 lbs (157 kg) 357 lbs (162 kg) 375 lbs (170 kg)

Shipping Dimensions 267/8” (682 mm) W x 841/4” (1,240 mm) H x 297/8” (759 mm) D

Support

Call Miele (800) 999-1360

Miele Website 8www.mieleusa.com

20/20 Link 82020technologies.com

K 2601 Vi (Right Hinged)Item 36260101USA

K 2611 Vi (Left Hinged)Item 36261101USA

F 2661 Vi (Right Hinged)Item 37266101USA

F 2671 Vi (Left Hinged)Item 37267101USA

KWT 2601 Vi (Right Hinged)Item 36260105USA

KWT 2611 Vi (Left Hinged)Item 36261105USA

Page 2 of 12

KWT 2661 ViS (Right Hinged)Item 36266105USA

KWT 2671 ViS (Left Hinged)Item 36267105USA

CUTOUT DIMENSIONS

• Niche depth assumes a 3/4” (19 mm) panel, please adjust according to custom panel thickness


CUTOUT DETAILS

• The electrical connection must not be positioned higher than 9” (228.6 mm) above the floor.

• The 1/4” (6.4 mm) plumbed water connection should not be positioned higher than 2” (50.8 mm) above the floor.

Notes:In case of an emergency the electrical outlet must be easily accessible and must not be concealed behind the appliance.

Page 3 of 12

POWER SUPPLY AND WATER CONNECTION(Water Connection For F 26x1 Vi Only)


Water connection is located in front of unit.1/4” compression fitting is needed.

Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp - NEMA 5-15 molded plugWater line - 1/4” flexible water line - not included

Rear View Front View

Electrical Connection

Side View

Page 4 of 12

CUSTOM PANEL INSTALLATIONS

Width: 29 3/4" in all cases

Thickness: Minimum 3/4" outside frame

Height: Determined using the following calculation:

Panel Height = HOC - TKH

HOC = Total height of cabinet or side panelTKH = Toe-kick height

Note: Finish back side of panels to insure appearancePanel may extend above unit. This is notconsidered in height calculation

Maximum panel weight: 105.8 Pounds

MieleFully Integrated

Freezer

TKH

HO

C

Pane

l Hei

ght

These units do not come equipped with a front panel. They are designed to accept a custom door panel supplied bythe cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surroundingcabinets.

Panel size is determined in the following manner:

Panel NotesIf the adjoining cabinets are taller than the height of machine (HOM) - the front panel may be extended accordingly.Simply maintain the toekick height and extend the panel the needed distance.

Adjoining cabinet

Machine

Extended Panel

106 Pounds

Minimum 23 3/4” (604 mm)

Minimum 3/4” (19 mm) outside frame

Fully Integrated 24” MasterCool | K 26x1 Vi

Page 5 of 12

Fully Integrated 24” MasterCool | K 26x1 Vi

DOOR PANEL DIMENSIONSKFP 2404 - Door Panel

Available as an accessoryfor the following models:• K 26x1 Vi

Page 6 of 12


Fully Integrated 24” MasterCool | F 26x1 Vi

Page 7 of 12










Freezer

TKH

HO

C

Pane

l Hei

ght




Adjoining cabinet

Machine

Extended Panel

143 Pounds

23 3/4” (604 mm) in all cases


Pan

el "

B"

Hei

ght

Width: 29 3/4" in all casesThickness: Minumum 3/4" outside frame

Standard Upper Panel Height: 53 5/16"


Upper Maximum panel weight : 103.6 Pounds

Lower Panel Height: Use the following calculation:

Panel Height = HOM - 53 9/16 - TKH

HOM = Total height of machine. Can be adjusted tomatch adjoining cabinets - typically 84"HOM is adjustable between 83 1/2" - 85 3/8"

TKH = Toe-kick height (2" - 8 3/8")

Lower Maximum panel weight: 22 Pounds

Upper Panel

TKH

HO

M

Pan

el H

eigh

t



Lower Panel

Upper Panel NotesIf the adjoining cabinets are taller than the height of machine (HOM) - the upper panel may be extended accordingly.Find the difference between height of the adjoining cabinets and the height of machine (HOM) and add to 53 5/16"

Adjoining cabinet

Machine

Extended Panel Example:Ajoining cabinet height: 87"Height of machine: 84"Difference: 3"

Extended panel height: 56 5/16"









Freezer

TKH

HO

C

Pane

l Hei

ght




Adjoining cabinet

Machine

Extended Panel

Fully Integrated 24” MasterCool | F 26x1 Vi

DOOR PANEL DIMENSIONS & DISPENSER CUTOUTKFP 2444 - Door Panel

Available as an accessoryfor the following models:• F 26x1 Vi

Page 8 of 12

Pan

el "

B"

Hei

ght

Width: 29 3/4" in all casesThickness: Minumum 3/4" outside frame

Standard Upper Panel Height: 53 5/16"


Upper Maximum panel weight : 103.6 Pounds

Lower Panel Height: Use the following calculation:

Panel Height = HOM - 53 9/16 - TKH

HOM = Total height of machine. Can be adjusted tomatch adjoining cabinets - typically 84"HOM is adjustable between 83 1/2" - 85 3/8"

TKH = Toe-kick height (2" - 8 3/8")

Lower Maximum panel weight: 22 Pounds

Upper Panel

TKH

HO

M

Pan

el H

eigh

t



Lower Panel

Upper Panel NotesIf the adjoining cabinets are taller than the height of machine (HOM) - the upper panel may be extended accordingly.Find the difference between height of the adjoining cabinets and the height of machine (HOM) and add to 53 5/16"

Adjoining cabinet

Machine

Extended Panel Example:Ajoining cabinet height: 87"Height of machine: 84"Difference: 3"

Extended panel height: 56 5/16"

Fully Integrated 24” MasterCool | KWT 26x1 Vi(S)

Page 9 of 12

CUSTOM PANEL INSTALLATIONSCUSTOM PANEL INSTALLATIONS

137 Pounds

10 1/8” (257 mm) min.

5 7/8” (140 mm) min.

23 3/4” (604 mm)in all cases


2 1/2” - 3 1/4”(63.5 - 82.5 mm)

Both Sides

17 1/4” - 18 5/8”(439 - 473 mm)

63 7

/8” (

1623

mm

) max

.

Fully Integrated 24” MasterCool | KWT 26x1 Vi(S)

DOOR PANEL DIMENSIONSKFP 2454 -Door Panel

Available as an accessoryfor the following models:• KWT 26x1 Vi(S)

Page 10 of 12

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09

snoitpo ssenkcihTsnoitpo ssenkcihT

Door Swing

NOTE: Additional space needed depending onthickness of front panels and handle used

38 11

/16"

7/16"

Door Swing

16 7/8"MAX


HINGING DETAILS 115° OPENING

3”(76.2mm)

1-3/4”(44.5mm)

1-3/8”(35mm

)1-1/6” (29.6m

m)

1/4”(6.4mm

)17/24” (18m

m)

2-1/24”(52mm)2-1/3” (59mm)2-5/8” (67mm)

3”(76.2mm)

1-3/4”(44.5mm)

1-3/8”(35mm

)1-1/6” (29.6m

m)

1/4”(6.4mm

)17/24” (18m

m)

2-1/24”(52mm)2-1/3” (59mm)2-5/8” (67mm)

0-3/4” (19 mm

)1” (25 m

m)

1-1/4” (32 mm

)1-1/2” (38 m

m)

1-3/4” (44 mm

)

1-1/2” (38 mm)

1-1/4” (32 mm)

1” (25 mm)

0-3/4” (19 mm)

0-1/8” (3 mm)


Available for the following models:• K 26x1 Vi• F 26x1 Vi• KWT 26x1 Vi(S)

Page 11 of 12

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 1

1/16

"

7/16"

Door Swing

16 7/8"MAX


DOOR SWING AT 115° OPENING 11 3/4”(298 mm)

Max

HINGING DETAILS 90° OPENING

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 11

/16"

7/16"

Door Swing

16 7/8"MAX


7/16”(11 mm)

1-3/16”(30mm)

1-7/16”(36.5mm)

1-11/16”(43mm)

1-15/16”(49.2mm)

Handle or object that is NOT flush with Cabinet Front.

0-3/4” (19 mm

)1” (25 m

m)

1-1/4” (32 mm

)1-1/2” (38 m

m)

1-3/4” (44 mm

)2” (51 m

m)

0-3/4” (19 mm)

1” (25 mm)

1-1/4” (32 mm)

1-1/2” (38 mm)

0-1/8” (3 mm)

When installing hinge side next to an appliance or object that is within range of the door panel, limit the door opening angle to 90°. This is done by installing the banking pin as illustrated. Insert the banking pin through the holes and drive in with a hammer.

Specification Sheets TRS 05202019


Available for the following models:• K 26x1 Vi• KWT 26x1 Vi(Si

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing

32 1

1/16

"

7/16"

Door Swing14 3/8"MAX

NOTE: Additional space needed depending on the thicknessof front panels and handle used.Freezer units cannot be stop pinned at 90°

NOTE: Additional space needed depending on the thicknessof front panels and handle used.Freezer units cannot be stop pinned at 90°

Page 12 of 12

0-1/8"

Front Panel

1"1-1/4"

1-1/2"

0-3/4"

0-3/4"

1-1/4"1-1/2"1-3/4"2" 1"

Cabinet Front

0-3/4"

1"1-1/4"1-1/2"

0-1/8"

FrontPanel

0-3/4"

1-1/4"1-1/2"1-3/4" 1"

Cabinet Front

rooD °511rooD °09


Door Swing


38 1

1/16

"

7/16"

Door Swing

16 7/8"MAX


26 11

/16” (

676

mm

)

DOOR SWING AT 90° OPENING 7/16” (11 mm)

Documents

Fully Integrated 24” MasterCool - us.mieleusa.com · the cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surrounding cabinets