Embed Size (px)
Citation preview
Cen
ter w
ing
stru
t ang
le g
uage
(Mak
e 2)
Landing gear strut angle guage(M
ake 1)
Motor sticksupport
Cut hole for motor wires
Cut two holes for battery cooling
F-1Side support/battery tray
Cut
slo
t for
0.1
25"
dia
x 8.
75"
carb
on tu
be a
xle
Land
ing
gea r
win
g(M
a ke
2, la
min
ate,
an
d sa
nd to
airf
oil s
h ape
)
match upper fuselage curvature
Mot
or s
tick
side
sup
ports
/ba
ttery
tray
(Mak
e 2)
Slot for rudder threads
Hole for elevator pushrod
F-4
Cut lightening
hole
Motor sticksupport
F-2
Cut two holes for battery cooling and
wiring access
Side support/battery tray
F-3
Hole for elevator pushrod
Wheels used on prototype (for 3.0" O.D.
O-rings) (Make 2)
2.75" dia.
Wheel hubs(Make 2 eachfrom 1/32" ply)
Inboard
3/4" dia.9/16" dia.
Drill all wheel hubs for 1/8" dia. carbon tube axle
Outboard
Optional scale wheels(for 3.5" O.D. O-rings)
(Make 2)
3.25" dia.9/16" dia.
Wheel axle stop(Make 2 from1/8" lite-ply)
Fwd landing gear strut doubler
(Make 2)
Fwd w
ing strut doubler(M
ake 2)
Aft landing gear/aft wing strut doubler
(Make 4)
Fwd
fuse
lage
bot
tom
(Mak
e 1)
Aileron connectors(Make 6 from 1/32" ply)
Aileron control horns(Make 2 from 1/32" ply)
Cen
ter w
ing
stru
t ang
le g
uage Landing gear strut angle guage
Bas
e cr
oss
piec
e fo
r al
l alig
nmen
t gua
ges
(Mak
e 2)
Upper wing alignment guage(Make 2)
Cut
slo
t for
0.1
25"
dia
x 8.
75"
Land
ing
gea r
win
g(M
a ke
2, la
min
ate,
an
d sa
nd to
airf
oil s
h ape
)
Center w
ing struts
(Make 2 from
1/8" lite ply)
Land
ing
gear
stru
ts(M
ake
2 fro
m 1
/8" l
ite p
ly)
Upper wing alignment guage2nd layer of cowling
(Make 1)
Motor stick support(Make 2)
Servo tray location
Wing alignment marks
Aft landing gear strut doubler
Fwd landing gearstrut doubler
F-1 F-2
Top overwing fairing(Make 1)
Sand sides to rounded shape to
match upper fuselage curvature
Servo tray(Make 2 and
laminate)
GWS Pico servos shown
Inner layers of cowling(Make 7)
Fuselage sides(Make 2)
Wing alignment marks
F-4
Turtledeck top(Make 1 from 3mm Depron)
Cut cockpit hole AFTER installing
turtledeck top
Fwd fuse top(Make 2 and laminate)
Cut hatch to access batteryafter installation
Aft fuselage bottom(Make 1 from 3mm Depron)
Turtledeck top(Make 1 from 3mm Depron)
Turtledeck/stabilizertrim piece
(Make 1 from 3mm Depron)
Elevator control horns(Make 1 from 1/32" ply) Rudder control horn
(for pull-pull threads)(Make 1 from 1/32" ply)
1/4" square hardwood joiner
(bevel 45 degrees on leading edge)
Cut slot to
fit wing strutsVertical tail(Make 1)
Tail skid(Make 1 from1/8" lite-ply)
Front of cowling(Make one from 3mm Depron)
Fwd wing strut doubler Aft wing strut doubler
F-1 F-2
0.188" dia x 28.5"carbon tube spar
F-3
Bevel top edge of aft fuselage to match curvature of turtledeck top
F-4
0.188" dia x 28.5"carbon tube spar
Lower wing(Make 1)
Exit hole for elevator pushrod(right side only)
Cut access hatch for receiver
Cut slot to
fit wing struts
Tail skid support(M
ake 1)
Exit holes for rudder threads(both sides)
Exit hole for elevator pushrod(right side only)
(Make 1)
1/4" square hardwood joiner
(bevel 45 degrees on leading edge)
Cut slot to
fit wing struts
Horizontal tail(M
ake 1)
Main wing struts(Make 2 from 1/8" lite-ply)
0.157" dia x 27.2"carbon tube spar
Middle wing(Make 1)
0.157" dia x 27.2"carbon tube spar
1.0"
Cut slot to
fit wing struts
Copyright © 2005 All Rights Reserved
All parts are made from 6 mm Depron or BlueCore foam unless otherwise specified
Designed by Steve Shumate
If you enjoy these plans, please consider sending a small contribution to the designer to show your appreciation for the work that went into
them. Suggested contribution is $5 to $10 U.S., and can be sent via PayPal to [email protected]. Thanks for your support!
�������������� ���
Cut slot to
fit wing struts
Upper wing(Make 1)
0.188" dia x 31.5"carbon tube spar
Cut slot to
fit wing struts
