Upload
harlygan
View
30
Download
9
Embed Size (px)
Citation preview
For Technical Assistance and Sales Contact:
FlexEJ Ltd
Tel: +44 (0) 1384 881188
Fax: +44 (0) 1384 896875
Email: [email protected]
Web: www.flexej.co.uk
RE
F: 2
817F
LX
Section
Rubber Bellows - Elaflex 1Premium Quality joints available in a wide range of materials and standard configurations. Workingtemperatures to 130°C and working pressures to 25bar, suitable for potable water, HVAC, food,pharmaceutical, chemical, marine and industrialapplications. Full range of flange standards, choice of flange materials, tied units, liners and flame protection covers.
Rubber Bellows - SeniorFlex 2Commercial Quality primarily applied in HVACapplications. Bellows available in EPDM with PN flanges galvanised carbon steel.
Rubber Bellows - Safetech 3Fully engineered large diameter arch rubberbellows, available in a wide range of materialsand accessories to suit demanding industrial,power, petrochemical and refineryapplications.
Expansion Joints - Metallic 4FlexEJ offer metallic expansion joints suitable for every application including HVAC, commercial, industrial, petrochemical and refinery.
Hose - Rubber 5Range includes FlexEJ type FBH fancoilhose manufactured from EPDM rubber with stainless steel outer braid and nickel-plated brass end fittings.
Hose - Metallic 6FlexEJ type FSH Engineered metallic flexiblehose to suit specific pressure, temperature,movement or vibration requirements. Endconnections and flange standards to suitclient specific requirements. Screwed and buttweld pipe connections also available.
HVAC - Air & Dirt Seperators + Dosing Pots 7Flexej Air and Dirt Seperators can be used inboth heating and cooling systems to removetrapped air and dirt particles from the fluid.Dosing pots are used to feed liquid chemicals intoclosed systems safely.
INDEX
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-1
Available Elaflex ERV Rubber Expansion Joints: Types and Lengths
DN Red Band Rotex CR ERP
25 130 130 130 130
32 130 160 130 160 130 130
40 130 160 130 160 130 130
50 130 150 160 130 160 130 130
65 130 150 160 130 160 130 130
80 130 150 160 130 150 160 130 130
100 130 150 160 130 150 160 130 130
125 130 150 160 130 150 160 130 130
150 130 150 160 130 150 160 130 130
200 130 150 160 175 130 150 160 175 130
250 130 175 200 130 175 200 130
300 130 200 130 200 130
350 200 200 200
400 200 200 200
500 200 200 200
600 200 200 200
700 275 260 260
800 250 250 250
900 300 300 300
1000 300 300 300
DN Yellow Band Yellow Steel Yellow Orange Green VITEX WhiteLT
25 130 130 130 130 130 130 130
32 130 160 130 130 130 130 130 130
40 130 160 130 130 130 130 130 130
50 130 150 160 130 130 130 130 130 130
65 130 150 160 130 130 130 130 130 130
80 130 150 160 130 150 130 130 130 130 130
100 130 150 160 130 150 130 130 130 130 130
125 130 150 160 130 150 130 130 130 130
150 130 150 160 130 150 130 130 130 130
200 130 150 160 175 130 175 130 130 130 130
250 130 175 200 130 175 130 130 130
300 130 200 130 200 130 130 130
350 200 200 200 200
400 200 200 200 200
500 200 200 200 200
600 200 200 200 200
700 275 260
800 250
900 300
1000 300
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -2 FlexEJ copyright 2011- R3/11
Overview of Certificates
ERV-GS ERV-G ERV-R ROTEX ERV-CRApprovals
Other
Germanischer Lloyd
Lloyd‘s Register
Bureau Veritas
Det Norske Veritas
American Bureau of Shipping
Nippon Kaiji Kyokai
China Classification Society
TechnischerÜberwachungs Verein
Bundesamt für Wehrtechnikund Beschaffung
Deutscher Verein desGas- und Wasserfachs
Attestation de ConformitéSanitaire
See-Berufsgenossenschaft
Gasgas
TrinkwasserDrinking water
TrinkwasserDrinking water
MED
DIN 4809
PDF download under www.flexej.co.uk
Type Liner Key Feature Page
Water andWaste Water
ERV-R Butyl (IIR) / EPDM 1-7With drinking water approval
ROTEX EPDM 1-9TÜV approved for heating systems
ERV-CR CR 1-11The economical option
ERP ERP Butyl (IIR) / EPDM 1-13Extra flexible
Petroleum Based Products, Liquified Petroleum Gas
ERV-G NBR 1-15For tank trucks, refineries and petrol stations
ERV-GS NBR 1-17Fire resistant for 30 minutes at 800° C
ERV-GSHNBR 1-19
HNBR For extremely demanding conditions: -35°C to 120°C
ERV-G LT NBR 1-21For low temperatures up to -40° C
ERV-OR NBR 1-23For LPG and other gases up to 25 bar
Chemistry and Foodstuff
ERV-GR CSM 1-25For aggressive acids, lyes and chemicals
VITEX FPM 1-27For media with more than 50% aromatics, Biodiesel etc.
NBR hellERV-W 1-29
NBR bright coloured Confirming to foodstuff standards
ERV-TA PTFE 1-35Extensive chemical resistance, FDA conform
Flanges, Accessories and Hints
DIN, ASA, SAE, BS, VG, TW, JIS 1-31Flanges
ZS /ZSS1-34
RGTie rods, axial and angular limiters
SR Zubehör1-35
TA /TAS AccessoriesInner protective sleeves, PTFE linings, PTFE vacuum support rings
VSD /VSR1-36
VSRVVaccum support spirals, -support rings
FSH 1-37Flame protection covers
Overview of ERV Certificates 1-2
Hints for the Pipework Designer 1-38
Installation Hints for ERV Expansion Joints 1-39
Information concerning the Pressure Equipment Directive 1-40
Accessories
CR
LT
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-3
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 TABLE OF CONTENTS
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -4 FlexEJ copyright 2011- R3/11
Order Number Breakdown
ERV Type
= ERV-RRED BAND
= ROTEXROTEX
= ERV-CRCR
= ERPRED SPOT
= ERV-GYELLOW BAND
= ERV-GSYELLOW STEEL
= ERV-GSYELLOW STEEL HNBR
HNBR
= ERV-G LTYELLOW BAND LT
= ERV-ORORANGE BAND
= ERV-GRGREEN BAND
= VITEXVITEX
= ERV-WWHITE BAND
DN[mm]
25
32
40
50
65
80
100
125
150
200
250
300
350
400
500
600
700
800
900
1000
Length 1) up to DN 300 [mm]
130 = (Standard)
150 = x150
160 = x160
175 = x175
200 = x200
Flange type 1) 2)
DIN PN 6 = .6
DIN PN 10 = .10
DIN PN 16 = .16
DIN PN 25 = .25
DIN PN 40 = .40
ASA 150 = .ASA 150
ASA 300 = .ASA 300
SAE = .SAE
BS Table D = .BS 10D
BS Table E = .BS 10E
BS Table F = .BS 10F
VG 95959-1 = .VG 95959-1
DIN 28460 = .TW
JIS 5K = .JIS 5K
JIS 10K = .JIS 10K
JIS 16K = .JIS 16K
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-5
Section
1
Flange Material 3)
Zinc plated steel S235 JRG2 = (Standard)
Stainless Steel 316 Ti = SS
Bronze GBz 12 = Bz
Aluminium AlMg3 = Al
Hot galvanized steel = FVZ
RILSAN coated steel = RILSAN
Accessories 1)
PTFE lining = TA
PTFE lining and PTFE vacuum support ring = TAS
Vacuum support spiral = VSD
Vacuum support ring = VSR
Bolted vacuum support ring = VSRV
Tie rods with outer limitation = ZS
Tie rods with inner and outer limitation = ZSS
Flame protection cover = FSH
Angular limiter = RG
Inner protection sleeve = SR
1) Possible combinations can be seen on the following data sheets.
2) When using different flange connections at one ERV both are mentioned and separated with a dash, e.g. 16/ASA 150.
3) Tank truck flanges DN 50 - 150 are generally of aluminium. The steel version needs a "St" at the end of the order text.
Examples
ERV-R 50.ASA 150 ZS VSD = RED BAND rubber expansion joint DN 50 mm, length 130 mm, with zinc plated steel flanges ASA 150 incl. tie rods and vacuum support spiral
ROTEX 32x160.16SS = ROTEX rubber expansion joint DN 32 mm, length 160 mm, with stainless steel flanges DIN PN 16
ERV-G 80.TW = YELLOW BAND rubber expansion joint DN 80 mm, length 130 mm, with aluminium flanges TW
VITEX 200.JIS 10K FVZ = VITEX rubber expansion joint DN 200 mm, length 130 mm, with hot dip galvanized steel flanges JIS 10 K
ERV-W 400.BS 10E FSH = WHITE BAND rubber expansion joint DN 400 mm, length 200 mm, with zinc plated steel flanges BS 10E and flame protection cover
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -6 FlexEJ copyright 2011- R3/11
Checklist for Expansion Joints
1. Medium• Chemical composition• Gaseous, liquid, paste-like• Abrasion
2. Operation conditions• Minimum and maximum temperature• Maximum pressure• Vacuum• Axial range of movement (elongation / compression)• Angular load• Lateral offset• Dynamic load
3. Installation Site• Indoor or outdoor installation• Exposure to sunlight (UV)• Salt-containing atmosphere
4. Classification acc. to Pressure Equipment Directive?Please regard the Pressure Equipment Directive, especially when gaseous media are used. Further Information on page 1-40.
Temperature depending working pressureType Working Temperature depending Bellow
Temperature max. range of movement* PN 10 PN 16 PN 25
ERV-R / ERV-CR / ERV-G 50°C 100% 10 bar 16 bar -
ERV-G LT / ERV-GR / VITEX 70°C 80% 8 bar 12 bar -
ERV-W 100°C 60% 6 bar 10 bar -
50°C 100% - - 25 bar
ERV-OR 70°C 80% - - 20 bar
100°C 60% - - 15 bar
50°C 100% 10 bar - -
ERP 70°C 80% 8 bar - -
100°C 60% 6 bar - -
70°C 100% 10 bar 16 bar -
ROTEX 100°C 75% 7,5 bar 12 bar -
130°C 50% 5 bar 8 bar -
ERV-GS / ERV-GS HNBR60°C 100% 10 bar 16 bar -
100°C 60% 6 bar 10 bar -
*) For type specific range of movement see data sheets. Depending on media, a reduction of working conditions may be necessary. Please ask our sales team in case of questions.
Temperature depending range of movement and pressure
The following list shows the dependencies of overpressure, range of movement and temperature for ERV expansion joints.
RED BAND expansion joints in High-Tech design for water,drinking water (approval DVGW W 270 as well as ACS), cold andwarm waste water, seawater, cooling water, also with chemicaladditives for water treatment, low concentrated acids and alkalis,salt solutions, technical alcohols, esters and ketones.Temperature(depending on medium) range -40°C up to +100°C, temporarily upto +120°C. Electrically dissipative.
Not suitable for all kinds of mineral oil products, cooling water withadded oil containing corrosion preventatives, oily compressor air.
Liner : Butyl (IIR) / EPDM, seamless, low permeation
Reinforcement : PA textile cord, Butyl rubberized
Cover : EPDM, ozone proof, heat resistant
Marking : Red band, ERV DN .., PN .., production date
Flanges1) : Swiveling, DIN PN 10/16, carbon steel, zinc plated
Type ERV-R
BL
DDN
lØ
Q
k Ø
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e ·
Co
pyr
ight
ELA
FLE
X
~~
Section
1
2011
1,9 15 1" 25 115 85 4 x 14 130 ERV-R 25.16 2)
3,4 130 ERV-R 32.1615 11/4" 32 140 100
3,6 160 ERV-R 32x160.16
4,0 130 ERV-R 40.1620 11/2" 40 150 110
4,2 160 ERV-R 40x160.16
4,6 130 ERV-R 50.16
4,7 30 2" 50 165 125 150 ERV-R 50x150.16
4,8 160 ERV-R 50x160.16
5,3 130 ERV-R 65.16
5,4 50 21/2" 65 185 145 150 ERV-R 65x150.16
5,5 160 ERV-R 65x160.16
6,9 130 ERV-R 80.16
7,0 85 3" 80 200 160 150 ERV-R 80x150.16
7,1 160 ERV-R 80x160.16
8,0 130 ERV-R 100.16
8,1 125 4" 100 220 180 150 ERV-R 100x150.16
8,2 160 ERV-R 100x160.16
9,9 130 ERV-R 125.16
10,1 185 5" 125 250 210 150 ERV-R 125x150.16
10,2 160 ERV-R 125x160.16
12,3 130 ERV-R 150.16
12,4 250 6" 150 285 240 150 ERV-R 150x150.16
12,5 160 ERV-R 150x160.16
16,5 130 ERV-R 200.10
16,6 150 ERV-R 200x150.10400 8" 200 340 295
16.7 160 ERV-R 200x160.10
16,8 175 ERV-R 200x175.10
21,6 130 ERV-R 250.10
21,9 600 10" 250 395 350 175 ERV-R 250x175.10
22,1 200 ERV-R 250x200.10
29,3 130 ERV-R 300.10800 12" 300 445 400
29,8 200 ERV-R 300x200.10
43,0 1000 14" 350 505 460 16 x 22 ERV-R 350.10
46,0 1375 16" 400 565 515 16 x 26 ERV-R 400.10
57,0 2185 20" 500 670 620 20 x 26 ERV-R 500.10
70,0 3080 24" 600 780 725 20 x 30 ERV-R 600.10
117,0 4800 28" 700 895 840 24 x 30 275 ERV-R 700.10
129,5 5440 32" 800 1015 950 24 x 33 250 ERV-R 800.10
184,0 7100 36" 900 1115 1050 28 x 33 ERV-R 900.10
245,0 8700 40" 1000 1230 1160 28 x 36 ERV-R 1000.10
FlexEJ copyright 2011- R3/11 1-7
RUBBER EXPANSION JOINTS ERV-R
16
10
16
16
10
16
12 x 22
8 x 22
8 x 18
4 x 18
10
300
200
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -8 FlexEJ copyright 2011- R3/11
Range of Movenment Type ERV-R
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
ApprovalsThese certificates for type ERV-R can be downloaded from www.flexej.co.uk
axial lateral angularLength Bellow size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
150 50 - 200 140 160 115 180 +- 30 +- 15
160 32 - 200 150 170 130 195 +- 35 +- 15
175200 165 185 160 210 +- 15 +- 5
250 165 185 160 210 +- 10 +- 5
200250 - 300 190 210 160 235 +- 30 +- 10
350 - 600 190 210 160 235 +- 30 +- 8
250 800 240 260 210 285 +- 35 +- 5
260 700 250 270 220 290 +- 30 +- 5
300 900 - 1000 290 310 260 340 +- 40 +- 5
ERV-R
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 50° C
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max. max. -700 -700 -700
withoutVSD / VSR
withVSD
withVSR
withVSRV
Permissable Vacuum [mbar]
Overview of all certificates on catalogue page 1-2
Application: Used as safety compensator in heating installations approved by TUEV acc.to DIN 4809 with temperatures up to 110° C by PN 6 bar. – For noise reduction, forcompensation of axial, lateral and angular movements. For allowable of movement see pageoverleaf. Ideal for demand usage e.g. in block heating power stations.
ROTEX RUBBER EXPANSION JOINTS
ROTEX expansion joints for permanent stressthrough hot heating water, cooling water and hot air. Approved according to DIN up to 100°C by 10bar and up to 110° C by 6 bar. Temperature rangedepending on medium) -40° C up to +130° C,temporarily up to +150° C. Electrically dissipative.
Not suitable for drinking water, cooling water with oil containing additives, oily compressor air,permanent effect of steam.
Liner : EPDM, hot water resistant, seamless, high abrasion resistance
Reinforcement : Polymer textile cord, hot water andhydrolysis proof
Cover : EPDM, ozone proof, heat resistantMarking : 2 red bands, ERV DN .., PN ..,
production dateFlanges1) : Swiveling, DIN PN 10/16, carbon
steel, zinc plated
2011
BL
Type ROTEX
D
DN
§l Ø
Q
k Ø
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e ·
Co
pyr
ight
ELA
FLE
X
~~
Section
1
FlexEJ copyright 2011- R3/11 1-9
1,9 15 1" 25 115 85 4 x 14 130 ROTEX 25.162)
3,4 130 ROTEX 32.1615 11/4" 32 16 140 100 4 x 18
3,6 160 ROTEX 32x160.16
4,0 130 ROTEX 40.1620 11/2" 40 16 150 110
4,2 4 x 18 160 ROTEX 40x160.16
4,6 130 ROTEX 50.1630 2" 50 16 165 125 4 x 18
4,8 160 ROTEX 50x160.16
5,3 130 ROTEX 65.1650 21/2" 65 16 185 145 4 x 18
5,5 160 ROTEX 65x160.16
6,9 130 ROTEX 80.16
7,0 85 3" 80 16 200 160 150 ROTEX 80x150.16
7,1 160 ROTEX 80x160.16
8,0 130 ROTEX 100.16
8,1 125 4" 100 16 220 180 8 x 18 150 ROTEX 100x150.16
8,2 160 ROTEX 100x160.16
9,8 130 ROTEX 125.16
9,9 185 5" 125 16 250 210 150 ROTEX 125x150.16
10, 160 ROTEX 125x160.16
12,3 130 ROTEX 150.16
12,4 250 6" 150 16 285 240 150 ROTEX 150x150.16
12,5 160 ROTEX 150x160.16
16,5 8 x 22 130 ROTEX 200.10
16,6 150 ROTEX 200x150.10400 8" 200 16 340 295
16,7 160 ROTEX 200x160.10
16,8 175 ROTEX 200x175.10
21,6 16 130 ROTEX 250.10
21,9 600 10" 250 16 395 350 175 ROTEX 250x175.10
22,1 10 12 x 22 200 ROTEX 250x200.10
29,3 16 130 ROTEX 300.10800 12" 300 445 400
29,7 10 200 ROTEX 300x200.10
43,0 1000 14" 350 10 505 460 16 x 22 200 ROTEX 350.10
46,0 1375 16" 400 10 565 515 16 x 26 200 ROTEX 400.10
57,0 2185 20" 500 10 670 620 20 x 26 200 ROTEX 500.10
70,0 3080 24" 600 10 780 725 20 x 30 200 ROTEX 600.10
117,0 4800 28" 700 10 895 840 24 x 30 260 ROTEX 700.10
129,5 5440 32" 800 10 1015 950 24 x 33 250 ROTEX 800.10
184,0 7100 36" 900 10 1115 1050 28 x 33 300 ROTEX 900.10
245,0 8700 40" 1000 10 1230 1160 28 x 36 300 ROTEX 1000.10
16
16
10
300
4 x 18
200
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -10 FlexEJ copyright 2011- R3/11
Range of Movement Type ROTEX
Overview of all certificates on catalogue page 1.2
ROTEX
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 70° C
withoutVSD / VSR
withVSD
withVSR
withVSRV
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 25 +- 10
250 - 300 125 140 115 160 +- 25 +- 5
150 80 - 200 140 160 120 170 +- 30 +- 5
160 32 - 200 150 170 130 185 +- 25 +- 15
175 200 - 250 165 185 145 205 +- 30 +- 10
200250 - 300 190 210 170 225 +- 25 +- 10
350 - 600 190 210 160 225 +- 25 +- 8
250 800 240 260 210 280 +- 25 +- 5
260 700 250 270 220 290 +- 25 +- 5
300 900 - 1000 290 310 260 335 +- 30 +- 5
Permissable Vacuum [mbar]
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max. max. -700 -700 -700
ApprovalsThese certificates for type ROTEX can be downloaded from www.flexej.co.uk
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Spec
ifica
tions
sub
ject to cha
nge with
out notic
e · Copyright E
LAFL
EX
RUBBER EXPANSION JOINTS CR
~~
Section
1
CR Expansion Joints for cold and warm water, swimming poolwater, sea water, waste water (weakly sour or alkaline) also oilcontaining, cooling water with protective oils against corrosion,lubricating oil, grease and air, compressed air. Temperature(depending on medium) -25° C up to +90° C, temporarily up to+100° C. Electrically non-conductive.
Not suitable for drinking water, acids, alkalis, chemicals, heating oil, diesel, gasoline and jet fuel, petroleum, solvents, otherhydrocarbons and hot compressed air.Liner : Chloroprene CR, seamless, abrasion resistantReinforcement : PA textile cordCover : Chloroprene CR,Marking : White imprint "CR", ERV DN .., PN ..,
production dateFlanges 1) : Swiveling, DIN PN 10/16 carbon steel,
zinc plated
Type ERV-CR1,5 15 1" 25 115 85 4 x 14 ERV-CR 25.16 2)
3,4 15 11/4" 32 140 100 ERV-CR 32.16
4,0 20 11/2" 40 150 110 ERV-CR 40.16
4,6 30 2" 50 165 125 ERV-CR 50.16
5,3 50 21/2" 65 185 145 ERV-CR 65.16
6,9 85 3" 80 200 160 ERV-CR 80.16
8,0 125 4" 100 220 180 ERV-CR 100.16
9,9 185 5" 125 250 210 ERV-CR 125.16
12,3 250 6" 150 285 240 ERV-CR 150.16
16,5 400 8" 200 340 295 ERV-CR 200.10
21,6 600 10" 250 395 350 ERV-CR 250.10
29,3 800 12" 300 445 400 ERV-CR 300.10
43,0 1000 14" 350 505 460 16 x 22 ERV-CR 350.10
46,0 1375 16" 400 565 515 16 x 26 ERV-CR 400.10
57,0 2185 20" 500 670 620 20 x 26 ERV-CR 500.10
70,0 3080 24" 600 780 725 20 x 30 ERV-CR 600.10
117,0 4800 28" 700 895 840 24 x 30 260 ERV-CR 700.10
129,5 5440 32" 800 1015 950 24 x 33 250 ERV-CR 800.10
184,0 7100 36" 900 1115 1050 28 x 33 ERV-CR 900.10
245,0 8700 40" 1000 1230 1160 28 x 36 ERV-CR 1000.10
D
DN
I Ø
Q
k Ø
BL
▼
▼
FlexEJ copyright 2011- R3/11 1-11
10
16
4 x 18
8 x 18
8 x 22
12 x 22
130
200
300
2011
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -12 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-CR
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
200 350 - 600 190 210 160 235 +- 30 +- 8
250 800 240 260 210 285 +- 35 +- 5
260 700 250 270 220 290 +- 30 +- 5
300 900 - 1000 290 310 260 340 +- 40 +- 5
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 50° C
withoutVSD / VSR
withVSD
withVSR
withVSRV
ApprovalsThese certificates for type ERV-CR can be downloaded from www.flexej.co.uk
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max. max. -700 -700 -700
Übersicht aller Zertifikate auf unserer Kataglogseite 472 / Overview of all certificates on catalogue page 1-2
ERV-CR
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
Permissable Vacuum [mbar]
DDN
l Ø
Q
k Ø
RED SPOT expansion joints for sanitary installations, highlyflexible for cold and warm water, pool water, sea water,drinking water. Temperature range (depending on medium) -40oC up to +90oC, temporarily up to +120oC. Electricallydissipative.
Not suitable for all kinds of mineral oil products, cooling waterwith added oil containing corrosion preventatives, oilycompressor air, for permanent working pressure > 10 bar.
Liner : Butyl (IIR) / EPDM, seamlessReinforcement : PA textile cordCover : EPDMMarking : Red spot, ERV DN .., PN 10,
production dateFlanges 1) : Swiveling, DIN PN 10 carbon steel,
zinc plated
BL
RUBBER EXPANSION JOINTS ERP
Type ERP
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e ·
Co
pyr
ight
ELA
FLE
X
~~
Section
1
FlexEJ copyright 2011- R3/11 1-13
1,8 15 1" 25 115 85 4 x 14 ERP 25.10
3,3 15 11/4" 32 140 100 4 x 18 ERP 32.10
3.9 20 11/2" 40 150 110 4 x 18 ERP 40.10
4,5 30 2" 50 165 125 4 x 18 ERP 50.10
5,2 50 21/2" 65 10 185 145 4 x 18 130 ERP 65.10
6,8 85 3" 80 200 160 8 x 18 ERP 80.10
7,9 125 4" 100 220 180 8 x 18 ERP 100.10
9,8 185 5" 125 250 210 8 x 18 ERP 125.10
12,2 250 6" 150 285 240 8 x 22 ERP 150.10
2)
2011
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -14 FlexEJ copyright 2011- R3/11
Range of Movement Type ERP
axial lateral angularLength Bellow Size Installation length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
13025 - 80 120 135 100 150 +- 30 +- 30
100 - 150 100 135 100 150 +- 30 +- 20
ERP
L lL
Allowable static range of movement in service with usage of collar flanges up to 50° C
withoutVSD / VSR
withVSD
withVSR
ApprovalsThis certificate for type ERP can be downloaded from www.fexej.co.uk
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
-300 -300 -300 -300 -200 -200 -200 -100
-500 -500 -400 -400 -400 -300
-500 -400
Overview of all certificates on catalogue page 1-2
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
Permissable Vacuum [mbar]
EL
1,9 15 1" 25 115 85 4 x 14 130 ERV-G 25.16 2)
3,4 130 ERV-G 32.16
3,6 160 ERV-G 32x160.16
4,0 130 ERV-G 40.16
4,2 160 ERV-G 40x160.16
4,6 130 ERV-G 50.16
4,7 ERV-G 50x150.16
4,8 160 ERV-G 50x160.16
5,3 130 ERV-G 65.16
5,4 150 ERV-G 65x150.16
5,5 160 ERV-G 65x160.16
6,9 130 ERV-G 80.16
7,0 150 ERV-G 80x150.16
7,1 160 ERV-G 80x160.16
8,0 130 ERV-G 100.16
8,1 150 ERV-G 100x150.16
8,2 160 ERV-G 100x160.10
9,9 130 ERV-G 125.16
10,1 150 ERV-G 125x150.16
10,2 160 ERV-G 125x160.16
12,3 130 ERV-G 150.16
12,4 150 ERV-G 150x150.16
12,5 160 ERV-G 150x160.16
16,5 130 ERV-G 200.10
16,6 150 ERV-G 200x150.10
16,7 160 ERV-G 200x160.10
16,8 175 ERV-G 200x175.10
21,6 130 ERV-G 250.10
21,9 175 ERV-G 250x175.10
22,1 200 ERV-G 250x200.10
29,3 130 ERV-G 300.10
29,8 200 ERV-G 300x200.10
43,0 1000 14" 350 16 505 460 16 x 22 ERV-G 350.10
46,0 1375 16" 400 16 565 515 16 x 26 ERV-G 400.10
57,0 2185 20" 500 670 620 20 x 26 ERV-G 500.10
70,0 3080 24" 600 780 725 20 x 30 ERV-G 600.10
117,0 4800 28" 700 895 840 24 x 30 275 ERV-G 700.10
129,5 5440 32" 800 1015 950 24 x 33 250 ERV-G 800.10
184,0 7100 36" 900 1115 1050 28 x 33 ERV-G 900.10
245,0 8700 40" 1000 1230 1160 28 x 36 ERV-G 1000.10
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
15 11/4" 32 140 100
20 11/2" 40 150 110
30 2" 50 165 125 150
50 21/2" 65 185 145
85 3" 80 200 160
125 4" 100 220 180
185 5" 125 250 210
250 6" 150 285 240
400 8" 200 340 295
600 10" 250 395 350
800 12" 300 445 400
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e ·
Co
pyr
ight
ELA
FLE
X
RUBBER EXPANSION JOINTS ERV-G
~~
Section
1
YELLOW BAND expansion joints in High-Tech design suitable forpetroleum based products, fuel ethanol blend e.g. E 85 andDIN EN fuels up to 50% aromatic content, also town gas andnatural gas, except for LP gas. Temperature (depending onmedium) range -20°C up to +90°C, temporarily up to +100°C.Electrically conductive.
Lining : NBR (nitrile), seamless, abrasion resistantReinforcement : PA textile cordCover : Chloroprene CRMarking : Yellow band, ERV DN.., PN .., production dateFlanges 1) : Swiveling, DIN PN
Type ERV-G
BL
FlexEJ copyright 2005 1-15
DDN
l Ø
Q
k Ø
16
16
10
10
10
16
300
200
12 x 22
8 x 22
8 x 18
4 x 18
2011
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -16 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-G
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
150 50 - 200 140 160 115 180 +- 30 +- 15
160 32 - 200 150 170 130 195 +- 35 +- 15
175 200 - 250 165 185 160 210 +- 10 +- 5
200250 - 300 190 210 160 235 +- 30 +- 10
350 - 600 190 210 160 235 +- 30 +- 8
250 800 240 260 210 285 +- 35 +- 5
260 700 250 270 220 290 +- 30 +- 5
300 900 - 1000 290 310 260 340 +- 40 +- 5
ERV-G
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 50° C
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max. max. -700 -700 -700
withoutVSD / VSR
withVSD
withVSR
withVSRV
ApprovalsThese certificates for type ERV-G can be downloaded from www.flexej.co.uk
Overview of all certificates on catalogue page 1-2
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
Permissable Vacuum [mbar]
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Weight Effect. Bellow Size Press. Flange 1) Length PartApp. Area DN Nom. Measurements mm BL Number
kg Q:cm2 in. mm bar D k Ø l x Ø mm Type
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e ·
Co
pyr
ight
ELA
FLE
X
~~
Section
1
RUBBER EXPANSION JOINTS ERV-GS
Type ERV-GS
FlexEJ copyright 2011- R3/11 1-17
BL
DN
l Ø
k Ø
D
Q
YELLOW STEEL expansion joints for petroleumbased products, DIN EN fuels up to 50% aromaticcontent, cooling water with oily anticorrosion additives, lubrication and hydraulic oil, seawater.Temperature (depending on medium) range -20°Cup to +90°C, temporarily up to +100°C. Fire resistant up to 30 min. and 800°C. Electrically conductive.
Liner : NBR (nitrile), seamless, abrasion resistant
Reinforcement : Steel wire cord
Cover : Chloroprene CR
Marking : 2 yellow bands, ERV DN .., PN .., production date
Flanges 1) : Swiveling, DIN PN 10 / 16, carbon steel, zinc plated
2011
2,0 10 1" 25 16 115 85 4 x 14 130 ERV-GS 25.162)
3,5 15 11/4" 32 16 140 100 4 x 18 130 ERV-GS 32.16
4,0 20 11/2" 40 16 150 110 4 x 18 130 ERV-GS 40.16
5,0 30 2" 50 16 165 125 4 x 18 130 ERV-GS 50.16
5,5 50 21/2" 65 16 185 145 4 x 18 130 ERV-GS 65.16
7,1 130 ERV-GS 80.16
85 3" 80 16 200 160 8 x 18
7,2 150 ERV-GS 80x150.16
8,3 130 ERV-GS 100.16
125 4" 100 16 220 180 8 x 18
8,4 150 ERV-GS 100x150.16
10,1 130 ERV-GS 125.16
185 5" 125 16 250 210 8 x 18
10,2 150 ERV-GS 125x150.16
12,6 130 ERV-GS 150.16
250 6" 150 16 285 240 8 x 22
12,7 150 ERV-GS 150x150.16
16,9 130 ERV-GS 200.10
400 8" 200 16 340 295 8 x 22
17,2 175 ERV-GS 200x175.10
22,3 130 ERV-GS 250.10
600 10" 250 16 395 350 12 x 22
22,6 175 ERV-GS 250x175.10
29,9 130 ERV-GS 300.10
800 12" 300 16 445 400 12 x 22
30,4 200 ERV-GS 300x200.10
44,0 1000 14" 350 16 505 460 16 x 22 200 ERV-GS 350.10
47,5 1375 16" 400 16 565 515 16 x 26 200 ERV-GS 400.10
57,5 2185 20" 500 10 670 620 20 x 26 200 ERV-GS 500.10
70,0 3080 24" 600 10 780 725 20 x 30 200 ERV-GS 600.10
16
10
200
8 x 22
12 x 22
4 x 18
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -18 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-GS
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
withVSD
withVSR
withVSRV
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 145 +- 15 +- 20
130 100 - 150 120 135 100 145 +- 15 +- 15
200 - 300 125 140 115 150 +- 10 +- 5
150 80 - 150 140 160 115 170 +- 15 +- 15
175 200 - 250 165 185 150 195 +- 15 +- 5
200300 - 350 190 210 160 230 +- 25 +- 10
400 - 600 190 210 160 230 +- 25 +- 5
L
ERV-GS
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 60° C
ApprovalsThese certificates for type ERV-GS can be downloaded from www.flexej.co.uk
Overview of all certificates on catalogue page 1-2
withoutVSD / VSR
Permissable Vacuum [mbar]
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. max. max. -800 -700 -700 -700 -700 -600 -400 -400 -300 -200
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -800 -700
max. max.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-19
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011RUBBER EXPANSION JOINTS ERV-GS HNBR
YELLOW STEEL HNBR expansion joints forpetroleum based products, DIN EN fuels up to50% aromatic content, cooling water with oilyanticorrosion additives, lubrication andhydraulic oil, seawater. Very good aging,weathering and ozone resistance. Temperature(depending on medium) range -35°C up to+100°C, temporarily up to +120°C. Electricallyconductive.
Liner : HNBR (nitrile), seamless, high abrasion resistance
Reinforcement : Steel wire cord
Cover : Chloroprene CR
Marking : Yellow-blue-yellow bands, ERV DN .., PN .., production date
Flanges 1) : Swiveling, DIN PN 10 / 16, carbon steel, zinc plated
BL
DN
l Ø
k Ø
D
Q
Type ERV-GS HNBR
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type~~
2,0 10 1" 25 16 115 85 4 x 14 130 ERV-GS HNBR 25.162)
3,5 15 11/4" 32 16 140 100 4 x 18 130 ERV-GS HNBR 32.16
4,0 20 11/2" 40 16 150 110 4 x 18 130 ERV-GS HNBR 40.16
5,0 30 2" 50 16 165 125 4 x 18 130 ERV-GS HNBR 50.16
5,5 50 21/2" 65 16 185 145 4 x 18 130 ERV-GS HNBR 65.16
7,1 130 ERV-GS HNBR 80.16
85 3" 80 16 200 160
7,2 150 ERV-GS HNBR 80x150.16
8,3 130 ERV-GS HNBR 100.16
125 4" 100 16 220 180 8 x 18
8,4 150 ERV-GS HNBR 100x150.16
10,1 130 ERV-GS HNBR 125.16
185 5" 125 16 250 210
10,2 150 ERV-GS HNBR 125x150.16
12,6 130 ERV-GS HNBR 150.16
250 6" 150 16 285 240 8 x 22
12,7 150 ERV-GS HNBR 150x150.16
16,9 130 ERV-GS HNBR 200.10
400 8" 200 16 340 295 8 x 22
17,2 175 ERV-GS HNBR 200x175.10
22,3 130 ERV-GS HNBR 250.10
600 10" 250 16 395 350 12 x 22
22,6 175 ERV-GS HNBR 250x175.10
29,9 130 ERV-GS HNBR 300.10
800 12" 300 16 445 400 12 x 22
30,4 200 ERV-GS HNBR 300x200.10
44,0 1000 14" 350 16 505 460 16 x 22 200 ERV-GS HNBR 350.10
47,5 1375 16" 400 16 565 515 16 x 26 200 ERV-GS HNBR 400.10
57,5 2185 16" 500 10 670 620 20 x 26 200 ERV-GS HNBR 500.10
70,0 3080 16" 600 10 780 725 20 x 30 200 ERV-GS HNBR 600.10
200
4 x 18
8 x 22
12 x 22
16
10
130
1) Examples. - Other flange standards and materials see catalogue pages 1-31/3.
2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -20 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-GS HNBR
withVSD
withVSR
withVSRV
L
ERV-GS HNBR
LEL lL
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. max. max. -800 -700 -700 -700 -700 -600 -400 -400 -300 -200
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -800 -700
max. max.
withoutVSD / VSR
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 145 +- 15 +- 20
130 100 - 150 120 135 100 145 +- 15 +- 15
200 - 300 125 140 115 150 +- 10 +- 5
150 80 - 150 140 160 115 170 +- 15 +- 15
175 200 - 250 165 185 150 195 +- 15 +- 5
200300 - 350 190 210 160 230 +- 25 +- 10
400 - 600 190 210 160 230 +- 25 +- 5
EL
Allowable static range of movement in service with usage of collar flanges up to 60° C
Permissable Vacuum [mbar]
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-21
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS ERV-G LT
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type~~
1,9 15 1" 25 115 85 4 x 14 ERV-G LT 25.162)
3,4 15 11/4" 32 140 100 ERV-G LT 32.16
4,0 20 11/2" 40 150 110 ERV-G LT 40.16
4,6 30 2" 50 165 125 ERV-G LT 50.16
5,3 50 21/2" 65 16 185 145 ERV-G LT 65.16
6,9 85 3" 80 200 160 ERV-G LT 80.16
8,0 125 4" 100 220 180 8 x 18 ERV-G LT 100.16
9,9 185 5" 125 250 210 ERV-G LT 125.16
12,3 250 6" 150 285 240 8 x 22 ERV-G LT 150.16
16,5 400 8" 200 340 295 8 x 22 ERV-G LT 200.10
21,6 600 10" 250 395 350 ERV-G LT 250.10
29,3 800 12" 300 445 400 ERV-G LT 300.10
4 x 18
12 x 22
8 x 22
16 130
BL
DN
l Ø
k Ø
D
Q
Type ER-G LT
YELLOW BAND LT expansion joints designed forlow temperature applications for petroleum basedproducts, diesel, heating oil up to +90°C, aviationfuel JET A1, kerosene, petroleum up to 60°C andgasoline up to 40°C. Temperature (depending onmedium) range -40°C up to +90°C, temporarily upto +100°C. Electrically dissipative.
Liner : NBR (nitrile), seamless, high abrasion resistance
Reinforcement : PA textile cord
Cover : Chloroprene CR
Marking : Yellow band with white "LT" , print, ERV DN .., PN 16, production date
Flanges 1) : Swiveling, DIN PN 10 / 16, carbon steel, zinc plated
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -22 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-G LT
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
ERV-G LT
LEL L
Allowable static range of movement in service with usage of collar flanges up to 50° C
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max.
withoutVSD / VSR
withVSD
withVSR
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
LEL lL
Permissable Vacuum [mbar]
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-23
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS ERV-OR
ORANGE BAND expansion joints for Liquid PetroleumGas (LPG) according to EN 589. For tank trucks andrefuelling stations. Temperature range (dependingon medium) -20°C up to +90°C, temporarily up to100°C. Electrically conductive.
Liner : NBR (nitrile), seamless
Reinforcement : PA textile cord
Cover : Chloroprene CR, pricked
Marking : Orange band, ERV DN .., PN 25, production date
Flanges 1) : Swiveling, DIN 2635/PN 40 carbon steel, zinc plated
BL
DN
l Ø
k Ø
D
Q
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type
2,0 15 1" 25 115 85 4 x 14 ERV-OR 25.252)
3,0 15 11/4" 32 140 100 ERV-OR 32.25
3,5 20 11/2" 40 150 110 4 x 18 ERV-OR 40.25
5,0 30 2" 50 25 165 125 130 ERV-OR 50.25
6,0 50 21/2" 65 185 145 ERV-OR 65.25
7,5 85 3" 80 200 160 ERV-OR 80.25
10,0 125 4" 100 235 190 8 x 22 ERV-OR 100.25
8 x 18
Type ERV-OR
~~
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -24 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-OR
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. max. max. max.
max. max. max. max.
Allowable static range of movement in service with usage of collar flanges up to 50° C
ERV-OR
LEL L
withoutVSD / VSR
withVSD
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
130 25 - 100 120 135 100 160 +- 30 +- 30
Permissable Vacuum [mbar]
Overview of all certificates on catalogue page 1-2
LEL lL
Approvals
This certificate for type ERV-OR can be downloaded from www.flexej.co.uk
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-25
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS ERV-GR
GREEN BAND expansion joints for chemicals,acids, alkalis and aggressive chemical wastewater. For oil-contaminated compressed air up to +90°C. Temperature range (depending onmedium) -20°C up to +100°C, temporarily up to 110°C. Electrically non-conductive.
Liner : Hypalon (CSM), seamless, high abrasion resistance
Reinforcement : PA textile cord
Cover : Hypalon (CSM)
Marking : Green band, ERV DN .., PN .., production date
Flanges 1) : Swiveling, PN 10/16, carbon steel, zinc plated
BL
DN
l Ø
k Ø
D
Q
Type ERV-GR
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type~~
1,9 15 1" 25 115 85 4 x 14 ERV-GR 25.16 2)
3,4 15 11/4" 32 140 100 ERV-GR 32.16
4,0 20 11/2" 40 150 110 ERV-GR 40.16
4,6 30 2" 50 165 125 ERV-GR 50.16
5,3 50 21/2" 65 16 185 145 ERV-GR 65.16
6,9 85 3" 80 200 160 ERV-GR 80.16
8,0 125 4" 100 220 180 8 x 18 ERV-GR 100.16
9,9 185 5" 125 250 210 ERV-GR 125.16
12,3 250 6" 150 285 240 8 x 22 ERV-GR 150.16
16,5 400 8" 200 340 295 8 x 22 ERV-GR 200.10
21,6 600 10" 250 395 350 ERV-GR 250.10
29,3 800 12" 300 445 400 ERV-GR 300.10
43,0 1000 14" 350 10 505 460 16 x 22 ERV-GR 350.10
46,0 1375 16" 400 565 515 16 x 26 ERV-GR 400.10
57,0 2185 20" 500 670 620 20 x 26 ERV-GR 500.10
70,0 3080 24" 600 780 725 20 x 30 ERV-GR 600.10
117,0 4800 28" 700 895 840 24 x 30 260 ERV-GR 700.10
200
130
4 x 18
12 x 22
8 x 22
10
16
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -26 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-GR
axial lateral angularLength Bellow Size installation length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
200 350 - 600 190 210 160 235 +- 30 +- 8
withVSD
withVSR
withVSRV
Permissable Vacuum [mbar]
ERV-GR
LEL L
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max.
withoutVSD / VSR
LEL lL
Allowable static range of movement in service with usage of collar flanges up to 50° C
ApprovalsThis certificate for type ERV-GR can be downloaded from www.flexej.co.uk
Overview of all certificates on catalogue page 1-2
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-27
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS VITEX
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type~~
1,9 15 1" 25 115 85 4 x 14 VITEX 25.16 2)
3,4 15 11/4" 32 140 100 4 x 18 VITEX 32.16
4,0 20 11/2" 40 150 110 4 x 18 VITEX 40.16
4,6 30 2" 50 165 125 4 x 18 VITEX 50.16
5,3 50 21/2" 65 185 145 4 x 18 VITEX 65.16
6,9 85 3" 80 16 200 160 8 x 18 130 VITEX 80.16
8,0 125 4" 100 220 180 8 x 18 VITEX 100.16
9,9 185 5" 125 250 210 8 x 18 VITEX 125.16
12,3 250 6" 150 285 240 8 x 22 VITEX 150.16
16,5 400 8" 200 340 295 8 x 22 VITEX 200.10
Working pressure up to 16 bar. Please note allowable utilisation ratio.
13016
BL
DN
l Ø
k Ø
D
Q
Type VITEX
VITEX expansion joints in High-Tech design withseamless FPM lining, a flexible safety compensatorfor petrochemical facilities, en gines, power stationsand flue gas desulphurisation plants. Suitable forstrain with aggressive media.Very goodresistance against hot oils, benzene, xylol, fuelswith an aromatic content of more than 50%, biodiesel, aromatic/chlorinated hydrocarbons andmineral acids. Excellent resistance againstweathering, ageing and ozone. Temperature range(depending on medium) from -15°C up to +90°C,temporarily up to 130°C.
Liner : FPM, seamless, no permeation, el. non-conductive
Reinforcement : PA textile cord, specially rubberized
Cover : ECO, electrically dissipative
Marking : White-green-white bands, ERV DN .., PN 16, production date
Flanges 1) : Swiveling, DIN PN 10/16, carbon steel, zinc plated
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -28 FlexEJ copyright 2011- R3/11
Range of Movement Type VITEX
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300
max. max. max. max. max. max. -600
max. max. max.
withVSD
withVSR
VITEX
LEL L
withoutVSD / VSR
axial lateral angularLength Bellow Size Installation Length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130 100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
EL lL
ApprovalsThis certificate for type VITEX can be downloaded from www.flexej.co.uk
Permissable Vacuum [mbar]
Overview of all certificates on catalogue page 1-2
Allowable static range of movement in service with usage of collar flanges up to 50° C
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-29
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS ERV-W
Weight Effect. Size Flanges 1) Length Part 1)
Area DN Measurements [mm] mm NumberPress
kg Q [cm2] in. mm bar D k Ø l x Ø BL Type~~
1,9 15 1" 25 115 85 4 x 14 ERV-W 25.16 2)
3,4 15 11/4" 32 140 100 ERV-W 32.16
4,0 20 11/2" 40 150 110 ERV-W 40.16
4,6 30 2" 50 165 125 ERV-W 50.16
5,3 50 21/2" 65 16 185 145 130 ERV-W 65.16
6,9 85 3" 80 200 160 130 ERV-W 80.16
8,0 125 4" 100 220 180 8 x 18 ERV-W 100.16
9,9 185 5" 125 250 210 ERV-W 125.16
12,3 250 6" 150 285 240 8 x 22 ERV-W 150.16
16,5 400 8" 200 340 295 8 x 22 ERV-W 200.10
21,6 600 10" 250 395 350 130 ERV-W 250.10
29,3 800 12" 300 445 400 ERV-W 300.10
43,0 1000 14" 350 10 505 460 16 x 22 ERV-W 350.10
46,0 1375 16" 400 565 515 16 x 26 ERV-W 400.10
57,0 2185 20" 500 670 620 20 x 26 ERV-W 500.10
70,0 3080 24" 600 780 725 20 x 30 ERV-W 600.10
200
WHITE BAND expansion joints for foodstuffs,also oil and fat containing food. Liner conforms toGerman foodstuff regulations. Not approved fordrinking water. Temperature range (depending onmedium) -20°C up to +90°C, temporarily up to100°C. Electrically non-conductive.
Liner : NBR bright coloured,seamless, abrasion resistant
Reinforcement : PA textile cord
Cover : Chloroprene (CR)
Marking : White band, ERV DN .., PN .., production date
Flanges 1) : Swiveling, PN 10/16, carbon steel, zinc plated
10
16
BL
DN
l Ø
k Ø
D
Q
4 x 18
8 x 22
12 x 22
Type ERV-W
1) Examples. - Other flange standards and materials see cataloguepages 1-31/3.2) For rubber expansion joints DN 25 bellows DN 32 are used.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -30 FlexEJ copyright 2011- R3/11
Range of Movement Type ERV-W
LEL LLEL lL
axial lateral angularLength Bellow Size installation length
BL DN EL min. EL max. L min. L max. l
[mm] [mm] [mm] [mm] [mm] [mm] [mm]
25 - 80 120 135 100 150 +- 30 +- 30
130100 - 150 120 135 100 150 +- 30 +- 20
200 115 140 105 160 +- 30 +- 10
250 - 300 125 140 120 160 +- 15 +- 5
200 350 - 600 190 210 160 235 +- 30 +- 8
withVSD
withVSR
withVSRV
Permissable Vacuum [mbar]
ERV-W
LEL L
DN 32 40 50 65 80 100 125 150 200 250 300 350 400 500 600 700 800 900 1000
max. max. max. -700 -600 -400 -300 -300 -300 -200 -100
max. max. max. max. max. max. -600 -400 -200
max. max. max. max. max. max. max. -700 -700
max. max.
withoutVSD / VSR
EL
Allowable static range of movement in service with usage of collar flanges up to 50° C
ApprovalsThis certificate for type ERV-W can be downloaded from www.flexej.co.uk
Overview of all certificates on catalogue page 1-2
Data measured at room temperature with new expansion joints and non swelling media. For swelling media use a safety factor. Acompressed installation improves the in the table listed vacuum resistance. The maxium permittable elongation (L max.) reduces thevaccum resistance by 50%. For this case we recommend to use vacuum support spirals or vaccum support rings (see catalogue page 1-36).
Dependencies of overpressure, range of movement and temperature please see table on catalogue page 1-6.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-31
Flange ChoiceSection
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 RUBBER EXPANSION JOINTS
FLANGE CHOICEFor the choice of flanges a great variety of combinations concerning geometrie, materials and coatings is available.
Also two different flange types on one compensator are possible.
On the following pages are the most common types and dimensions listed.
Special types are available upon request.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -32 FlexEJ copyright 2011- R3/11
Commonly used Flange Measurements
DIN PN 6 DIN PN 10 DIN PN 16 DIN PN 25 DIN PN 40Flange Standard
Part Number .6 .10 .16 .25 .40
DN D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø
mm in. mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
25 1" 115 85 4 14 115 85 4 14
32 11/4" 120 90 4 14 140 100 4 18 140 100 4 18
40 11/2" 130 100 4 14 150 110 4 18 150 110 4 18
50 2" 140 110 4 14 165 125 4 18 165 125 4 18
65 21/2" 160 130 4 14 185 145 4 18 185 145 8 18
80 3" 190 150 4 18 200 160 8 18 200 160 8 18
100 4" 210 170 4 18 220 180 8 18 235 190 8 22
125 5" 240 200 8 18 250 210 8 18 270 220 8 26
150 6" 265 225 8 18 285 240 8 22 300 250 8 26
200 8" 320 280 8 18 340 295 8 22 340 295 12 22 360 310 12 26 375 320 12 30
250 10" 375 335 12 18 395 350 12 22 405 355 12 26 425 370 12 30 450 385 12 33
300 12" 440 395 12 22 445 400 12 22 460 410 12 26 485 430 16 30 515 450 16 33
350 14" 490 445 12 22 505 460 16 22 520 470 16 26 555 490 16 33 580 510 16 36
400 16" 540 495 16 22 565 515 16 26 580 525 16 30 620 550 16 36 660 585 16 39
500 20" 645 600 20 22 670 620 20 26 715 650 20 33 730 660 20 36 755 670 20 42
600 24" 755 705 20 26 780 725 20 30 840 770 20 36 845 770 20 39
700 28" 860 810 24 26 895 840 24 30 910 840 24 36 960 875 24 42
800 32" 975 920 24 30 1015 950 24 33 1025 950 24 39 1085 990 24 48
900 36" 1075 1020 24 30 1115 1050 28 33 1125 1050 28 39 1185 1090 28 48
1000 40" 1175 1120 28 30 1230 1160 28 36 1255 1170 28 42 1320 1210 28 56
ANSI B 16.5 150 lb/sq. in. ANSI B 16.5 300 lb/sq. in. SAE J518 cFlange Standard
Part Number .ASA 150 .ASA 300 .SAE
DN D Ø k Ø n l Ø D Ø k Ø n l Ø G H I L n l Ø
mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm mm mm mm mm
25 1" 108 41/2" 79,4 31/8" 4 15,9 5/8" 123,8 47/8" 88,9 31/2" 4 19 3/4"
32 11/4" 117,5 45/8" 88,9 31/2" 4 15,9 5/8" 133,4 51/4" 98,4 37/8" 4 19 3/4" 80 58,7 30,2 75 4 13
40 11/2" 127 5" 98,4 37/8" 4 15,9 5/8" 155,6 61/8" 114,3 43/4" 4 22,2 7/8" 95 70 35,7 83 4 13
50 2" 152,4 6" 120,7 43/4" 4 19 3/4" 165,1 61/2" 127 5" 8 19 3/4" 102 78 43 95 4 13
65 21/2" 177,8 7" 139,7 51/2" 4 19 3/4" 190,5 71/2" 149,2 57/8" 8 22,2 7/8" 114 89 51 115 4 13
80 3" 190,5 71/2" 152,4 6" 4 19 3/4" 209,6 81/4" 168,3 65/8" 8 22,2 7/8" 134 106,4 62 125 4 18
100 4" 228,6 9" 190,5 71/2" 8 19 3/4" 254 10" 200 77/8" 8 22,2 7/8" 162 130 78 147 4 18
125 5" 254 10" 215,9 81/2" 8 22,2 7/8" 279,4 11" 235 91/4" 8 22,2 7/8" 190 152,4 92,1 170 4 18
150 6" 279,4 11" 241,3 91/2" 8 22,2 7/8" 317,5 121/2" 269,9 105/8" 12 22,2 7/8"
200 8" 342,9 131/2" 298,5 113/4" 8 22,2 7/8" 381 15" 330,2 13" 12 25,4 1
250 10" 406,4 16" 361,9 141/4" 12 25,4 1" 444,5 171/2" 387,3 151/4" 16 28,6 11/8"
300 12" 482,6 19" 431,8 17 12 25,4 1" 520,7 201/2" 450,8 173/4" 16 31,7 11/4"
350 14" 533,4 21" 476,2 183/4" 12 28,6 11/8" 584,2 23" 514,3 201/4" 20 31,7 11/4"
400 16" 596,9 231/2" 539,7 211/4" 16 28,6 11/8" 647,7 251/2" 571,5 221/2" 20 34,9 13/8"
500 20" 698,5 271/2" 635 25 20 31,7 11/4" 774,7 301/2" 685,8 27" 24 34,9 13/8"
600 24" 812,8 32" 749,3 291/2" 20 34,9 13/8" 914,4 36" 812,8 32" 24 41,3 15/8"
identical with PN 16 identical with PN 40
Materials: zinc plated steel (standard), stainless steel, bronze, aluminium, hot galvanized steel, RILSAN coated steel etc. - see page 1-5
Materials: zinc plated steel (standard), stainless steel, bronze, aluminium, hot galvanized steel, RILSAN coated steel etc. - see page 1-5
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-33
Commomly Used Flange MeasurementsSection
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011
Flange Standard VG 95959-1 DIN 28460 "TW" JIS 5 K JIS 10 K JIS 16 KPart Number .VG 95959-1 .TW .JIS 5 K .JIS 10 K .JIS 16 K
DN D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø
mm in. mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
25 1" 125 90 4 19 125 90 4 19
32 11/4" 100 76 6 11 115 90 4 15 135 100 4 19 135 100 4 19
40 11/2" 108 84 6 11 120 95 4 15 140 105 4 19 140 105 4 19
50 2" 120 96 6 11 154 130 8 11,5 130 105 4 15 155 120 4 19 155 120 8 19
65 21/2" 140 116 8 11 154 130 8 11,5 155 130 4 15 175 140 4 19 175 140 8 19
80 3" 150 126 8 11 154 130 8 11,5 180 145 4 19 185 150 8 19 200 160 8 23
100 4" 172 148 10 11 174 150 8 14 200 165 8 19 210 175 8 19 225 185 8 23
125 5" 200 176 10 11 204 176 8 14 235 200 8 19 250 210 8 23 270 225 8 25
150 6" 226 202 12 11 240 210 12 14 265 230 8 19 280 240 8 23 305 260 12 25
200 8" 288 264 16 11 308 274 16 16 320 280 8 23 330 290 12 23 350 305 12 25
250 10" 385 345 12 23 400 355 12 25 430 380 12 27
300 12" 430 390 12 23 445 400 16 25 480 430 16 27
350 14" 480 435 12 25 490 445 16 25 540 480 16 33
400 16" 540 495 16 25 560 510 16 27 605 540 16 33
500 20" 655 605 20 25 675 620 20 27 730 660 20 33
600 24" 770 715 20 27 795 730 24 33 845 770 24 39
Flange Standard BS 10 table D BS 10 table E BS 10 table FPart Number .BS 10D .BS 10E .BS 10F
DN D Ø k Ø n l Ø D Ø k Ø n l Ø D Ø k Ø n l Ø
mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in.
25 1" 114,3 41/2" 82,5 31/4" 4 14,3 9/16" 114,3 41/2" 82,5 31/4" 4 14,3 9/16" 120,6 43/4" 87,3 37/16" 4 17,5 11/16"
32 11/4" 120,6 43/4" 87,3 37/16" 4 14,3 9/16" 120,6 43/4" 87,3 37/16" 4 14,3 9/16" 133,3 51/4" 98,4 37/8" 4 17,5 11/16"
40 11/2" 133,3 51/4" 98,4 37/8" 4 14,3 9/16" 133,3 51/4" 98,4 37/8" 4 14,3 9/16" 139,7 51/2" 104,8 41/8" 4 17,5 11/16"
50 2" 152,4 6" 114,3 41/2" 4 17,5 11/16" 152,4 6" 114,3 41/2" 4 17,5 11/16" 165,1 61/2" 127,0 5" 4 17,5 11/16"
65 21/2" 165,1 61/2" 127,0 5" 4 17,5 11/16" 165,1 61/2" 127,0 5" 4 17,5 11/16" 184,1 71/4" 146,0 53/4" 8 17,5 11/16"
80 3" 184,1 71/4" 146,0 53/4" 4 17,5 11/16" 184,1 71/4" 146,0 53/4" 4 17,5 11/16" 203,2 8" 165,1 61/2" 8 17,5 11/16"
100 4" 215,9 81/2" 177,8 7" 4 17,5 11/16" 215,9 81/2" 177,8 7" 8 17,5 11/16" 228,6 9" 190,5 71/2" 8 17,5 11/16"
125 5" 254 10" 209,5 81/4" 8 17,5 11/16" 254 10" 209,5 81/4" 8 17,5 11/16" 279,4 11" 234,9 91/4" 8 22,2 7/8"
150 6" 279,4 11" 234,9 91/4" 8 17,5 11/16" 279,4 11" 234,9 91/4" 8 22,2 7/8" 304,8 12" 260,3 101/4" 12 22,2 7/8"
200 8" 336,5 131/4" 292,1 111/2" 8 17,5 11/16" 336,5 131/4" 292,1 111/2" 8 22,2 7/8" 368,3 141/2" 323,9 123/4" 12 22,2 7/8"
250 10" 406,4 16" 355,6 14" 8 22,2 7/8" 406,4 16" 355,6 14" 12 22,2 7/8" 431,8 17" 381 15" 12 25,4 1"
300 12" 457,2 18" 406,4 16" 12 22,2 7/8" 457,2 18" 406,4 16" 12 25,4 1" 489 191/4" 438,1 171/4" 16 25,4 1"
I
L
GH
Dk Ø
l Øl Ø SAE
DINASABSVGTWJIS
Materials: zinc plated steel (standard), stainless steel, bronze, aluminium, hot galvanized steel, RILSAN coated steel etc. - (by "TW" up to DN 150 aluminium = standard) - see page 1-5
Materials: zinc plated steel (standard), stainless steel, bronze, aluminium, hot galvanized steel, RILSAN coated steel etc. - see page 1-5
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -34 FlexEJ copyright 2011- R3/11
ERV Tie Rods and Angular Limiters
Tied Flanges – Type ZSThe opposite table shows that the pressure thrust forcesin small ERV dimensions up to DN 50 are this low thatlimiters normally are not necessary. Limiters arerecommended when it is not possi ble to secure the pipesystem with sufficient fixed points or when a part relief ofthe fixed points is desired.
The required limiters are measured to absorb also thereaction forces resulting from the test pressure.
For the mainly required axial limitation the shown typeswith integrated tie bars have proved well. The tie barswith high stability (steel 8.8) can be adjusted to the actualinstallation meas urements. The tie bars lie elastically innoise reducing rubber bushes of weatherproof rubber -from DN 350 the tie rods lie in prinicipal in conical seatsand spherical washers.
DN Number Parttie rods*) Number
mm Type
Values for flanges DIN PN 10, number of tie rods may change with different flange standards.
Pressure thrust forces of ERV Expansion Joints(installation length = 130 mm)
Type ... ZS(up to DN 300) *)
Tie rods with outerlimitation in
rubber bushings
Type ... ZS(from DN 350) *)
Tie rods with outer limitation
in spherical discsand conical seats
Type ... ZSS(up to DN 300) *)
Tie rods with innerand outer limitation
Type ... RGAngular limiter
Special Designs
*)
25 2 ERV 25 … ZS
32 2 ERV 32 … ZS
40 2 ERV 40 … ZS
50 2 ERV 50 … ZS
65 2 ERV 65 … ZS
80 2 ERV 80 … ZS
100 2 ERV 100 … ZS
125 2 ERV 125 … ZS
150 2 ERV 150 … ZS
200 2 ERV 200 … ZS
250 2 ERV 250 … ZS
300 4 ERV 300 … ZS
350 4 ERV 350 … ZS
400 4 ERV 400 … ZS
500 4 ERV 500 … ZS
600 4 ERV 600 … ZS
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-35
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
ERV INNER SLEEVES AND PTFE LINING
25 22 ERV… 25…SR 1)
32 22 ERV… 32…SR
40 30 ERV… 40…SR
50 38 ERV… 50…SR
65 53 ERV… 65…SR
80 72 ERV… 80…SR
100 88 ERV…100…SR
125 112 ERV…125…SR
150 138 ERV…150…SR
200 190 ERV…200…SR
250 235 ERV…250…SR
300 290 ERV…300…SR
350 320 ERV…350…SR
400 390 ERV…400…SR
500 490 ERV…500…SR
600 590 ERV…600…SR
25 26 ERV… 25…TA 1)
32 26 ERV… 32…TA
40 34 ERV… 40…TA
50 44 ERV… 50…TA
65 59 ERV… 65…TA
80 72 ERV… 80…TA
100 92 ERV…100…TA
125 115 ERV…125…TA
150 138 ERV…150…TA
200 187 ERV…200…TA
250 235 ERV…250…TA
300 285 ERV…300…TA
50 44 ERV…50…TAS
65 59 ERV…65…TAS
80 72 ERV…80…TAS
100 92 ERV…100…TAS
125 115 ERV…125…TAS
150 138 ERV…150…TAS
200 187 ERV…200…TAS
250 235 ERV…250…TAS
300 285 ERV…300…TAS
Available for DN 25 - 300. Seamless liningwith sealing surface, virgin PTFE, approx.1 mm thickness. Delivered only as completefactory mounted unit with flanges.Unmounted lining not available. The allow -able movement range of the ERV is re -stricted by approximately 50%.
FDA conform.
Available for all ERV types DN 25 - 600.Thickness of stainless steel armouringdepending on DN between 1 and 3 mm.Lateral and angular movements aresignificantly reduced.
Conical sleeves available on request.
Please note: Between the bead (flangesurface) of the inner protection sleeve andthe counter flange an additional seal mustbe used.
Available for DN 50-300. Seamless PTFElining as "TA" but additionally with factorymounted support ring of solid PTFE. Theallowable movement range is restricted byapproximately 50%.
FDA conform.
ERV with PTFE - Lining. Used when the chemicalresistance of the chosen ERV type is not sufficient.Suitable for all kinds of liquids in use. Admissible workingtemperature of expansion joint has to be observed. Forworking pressure up to 6 bar - not suitable for vacuum.
Type TA
ERV with PTFE lining and PTFE vacuum support ring.Properties like type TA, but also suitable for vacuumservice, up to 70°C.
Type TAS
ERV with inner protection sleeve of stainless steel toprevent abrasion of the rubber liner, i.e. by granulates.Please note: the nominal bore is reduced.
DN D
Construction Details Diam. Part Materials Nom. Number
mm mm Type~~
D
1)For rubber expansion joints DN 25 bellows DN 32are used.
Type SR
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -36 FlexEJ copyright 2011- R3/11
Vaccum Support Spiral and Ring for ERV
DN D
Diam. PartNom. Number
mm mm Typevv
50 85 ERV… 50…VSD
65 110 ERV… 65…VSD
80 130 ERV… 80…VSD
100 180 ERV…100…VSD
125 230 ERV…125…VSD
150 270 ERV…150…VSD
200 320 ERV…200…VSD
250 420 ERV…250…VSD
300 500 ERV…300…VSD
125 175 ERV…125…VSR
150 190 ERV…150…VSR
200 260 ERV…200…VSR
250 300 ERV…250…VSR
300 350 ERV…300…VSR
350 410 ERV…350…VSR
400 480 ERV…400…VSR
500 580 ERV…500…VSR
600 680 ERV…600…VSR
500 545 ERV…500…VSRV
600 640 ERV…600…VSRV
700 780 ERV…700…VSRV
800 850 ERV…800…VSRV
900 1000 ERV…900…VSRV
1000 1085 ERV..1000…VSRV
Available for DN 50 - 300. Number of turnsand material thickness vary with DN. Thevacuum support spiral can be easilymounted subsequently. No 1 restriction ofadmissible pressure for ERV. Movementrange restricted by approximately 50%.
Available for DN 125 - 600. The vacuum support rings can be easily mounted sub -sequently. No restriction of admissible pressure for ERV. Movement range restricted by approximately 50%.
Available for DN 500 - 1000. The vacuum support rings can be easily mounted sub -sequently. No restriction of admissible pressure for ERV. Movement range restricted by approximately 50%.
ERV with vacuum support spiral. Spiral of AISI 316 Ti, used whenthe vacuum resistance of the chosen ERV is not sufficient.*)
Type VSD
ERV with vacuum support ring. Ring of AISI 316 Ti, used whenthe vacuum resistance of the chosen ERV is not sufficient.*)
Type VSR
Type VSRV
*) for Type VSD and VSR: Admissible vacuum see catalogue pages type specific ERV data sheets.
ERV with vacuum bolted support ring. For maximal vacuumresistance of the selected ERV. Bolted ring in stainless steel1.4571.*)
~~
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-37
Section
1
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011 FLAME PROTECTION COVER FOR ERV
25 30 170 FSH for ERV 25x130
32 40 190 FSH for ERV 32x130
40 45 195 FSH for ERV 40x130
50 60 210 FSH for ERV 50x130
65 75 225 FSHf for ERV 65x130
80 90 240 FSH for ERV 80x130
100 110 260260
FSH for ERV 100x130
125 135 285 FSH for ERV 125x130
150 160 330 FSH for ERV 150x130
200 220 385 FSH for ERV 200x130
250 265 435 FSH or ERV 250x130
300 315 485 FSH for ERV 300x130
25 30 170 FSH for ERV 25x160
32 40 190 FSH for ERV 32x160
40 45 195 FSH for ERV 40x160
50 60 210 FSH for ERV 50x160
65 75 225 FSH for ERV 65x160
80 90 240300
FSH for ERV 80x160
100 110 260 FSH for ERV 100x160
125 135 285 FSH for ERV 125x160
150 160 330 FSH for ERV 150x160
200 220 385 FSH for ERV 200x160
250 265 435 FSH for ERV 250x200
300 315 485340
FSH for ERV 300x200
DN I Ø D Ø Length L Part Numbermmmm mm mm Type
Type for ERV with flanges according to DIN PN 10/16
32 40 150 FSH - M for ERV 32x130
40 45 155 FSH - M for ERV 40x130
50 60 170 FSH - M for ERV 50x130
65 75 185 FSH - M for ERV 65x130
80 90 200 FSH - M for ERV 80x130
100 110 220260
FSH - M for ERV 100x130
125 135 245 FSH - M for ERV 125x130
150 160 270 FSH - M for ERV 150x130
200 215 345 FSH - M for ERV 200x130
250 265 395 FSH - M for ERV 250x130
32 40 150 FSH - M for ERV 32x160
40 45 155 FSH - M for ERV 40x160
50 60 170 FSH - M for ERV 50x160
65 75 185 FSH - M for ERV 65x160
80 90 200 FSH - M for ERV 80x160
100 110 220 300 FSH - M for ERV 100x160
125 135 245 FSH - M for ERV 125x160
150 160 270 FSH - M for ERV 150x160
200 215 345 FSH - M for ERV 200x160
250 265 395 340 FSH - M for ERV 250x200
Type for ERV with flanges according to VG 95959-1 (German Naval Standard)
Flame protection cover for ERV rubberexpansion joints, made of several layers ofglass fiber fabric with a surface cover ofsilver-coloured high temperature resistantsilicone-aluminium-glas fabric. Screws, nutsand washers of brass. It reliably protects theexpansion joint against radiation heat and directflames up to 800° C for 30 minutes. The flameprotection cover is resistant against oil andchemical influences as well as against ageingand weathering.
Because of its split design the flame protectioncover can be mounted subsequently or re-opened. The dimensions have been chosen insuch a way that also the counter flanges arecompletely covered. The allowed range ofmovement is not restricted.
Picture shows open condition
D
L
Type FSH
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -38 FlexEJ copyright 2011- R3/11
Hints for the Pipework Designer
ERV rubber expansion joints are delivered ready for installation. The swiveling flanges can be fitted inany desired position and have stabilising rims to ease the assembly. Flanges with stabilising rim (collar)also helps to maintain a safety gap between the ends of the screws and the bellow throughout thewhole range of movement and avoids injuries.
Correct Mating Flanges Seals are not required if the sealing surface of the mating flanges of the pipework are of the same size.Seals (as shown in fig. E) should be only used in order to prevent damage to the rubber sealing surface,for example if the mating flanges either have a larger internal diameter, sharp edges or irregularities e.g.welding beads.
Crushing StrengthThe maximum operating pressure and test pressure not only depends on the burst pressure of the rubber bellow but can also be affected by operating temperature and design pressure /nominal pressure of the used flanges. For full details please see page 1-6. The burst pressure (at roomtemperature) is at least 3 - 4 times the nominal pressure (PN). Pressure test certificates can be issuedupon request.
Vacuum ResistanceThe maximum vacuum depends on size, operating temperature, length of installation and theinstallation of vacuum support rings (page 1-36). Please see type specific data sheets for details. Thevacuum resistance can be slightly increased even without vacuum support rings if the installation length isshortened (e. g. by 20 mm). The vacuum resistance decreases if a longer installation length is chosen, orthe expansion joint is lengthened in operation.
Weather and Heat ResistanceThe outer rubber (cover) is resistant against weathering and protects the reinforcements against ageing,abrasion and corrosion. For the permitted temperature range please see type specific data sheets. Forpermanently warm operating conditions including external radiation heat please see page 1-6.
ERV types with an outer rubber of CR or Hypalon (CSM) are (within limits) oil proof and flame resistant.An additional flame protection can be achieved by using a flame protection cover conforming to the'Germanischer Lloyd' standard, see pages (1-37 and 1-17).
Pressure LossThe internal design of the ERV bellows allows a high flow with little turbulence. Therefore the pressureloss is usually neglectible, even when dealing with high flow rates.
Noise LevelsDue to their design, ERV expansion joints reduce noise in pipelines. An even better reduction isachieved if the total installation length is shortened in a range of 5 - 10 mm.
InstallationFor the allowable range of movement please see type specific data sheets. If possible, the length of theinstallation gap is designed to be equal to the recommended installation length, or slightly shorter. Thelow inherent resistance of ERV allows a compression by hand and makes fitting into smaller gaps easy.
For larger installation gaps or lateral offset, not more than 50% of the maximum area of movementshould be used up in order to leave a reserve for operation. If the bellows is lengthened during operation,a jolted (compressed) installation is recommended. The position of installation must be accessible for visualexamination. When installing the unit, installation hints (page 1-39) must be observed.
RestraintThe inherent resistance of ERV bellows is negligible in respect of calculations for anchorage points. Underpressure the bellow acts like a plunger, thus requiring to fix anchorage points for larger size expensionjoints. Since the ERV construction absorbs part of these forces, the anchorage points may becorrespondingly weaker. If such anchorage points cannot be provided, or if the stability of the other fittingsis insufficient, the pressure thrust forces have to be absorbed by tie rods. For available types see cataloguepage 1-34.
IdentificationAll ERV bellows have a vulcanised coloured type marking and an embossed text stating manufacturersmark, nominal width DN, nominal pressure PN as well as the manufacturing date.
right:
Flangeswith correctID helppreventdamageto rubber.
wrong:
Unevenend ofpipe cancausedamageto rubber
wrong:
Flangeswith toolargefemalediametercandamagerubber.
right:
Weld neckflanges withcorrect IDpreventdamageto rubber.
wrong:
Inneredge offlangesdamagesrubber
right:
In case ofB, D or F anadditionalflat seal can be usedto preventdamageto rubber
right:
Wellroundedsmoothegdepreventsdamageto rubber
A
F
E
G
C
D
B
stabilising rim
pipe stop
IDacc.toDIN
IDacc.toISO
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 1-39
Installation and Operation Hints for ERV Expansion Joints
Section
1
ELAFLEX expansion joints are provided ready forinstallation. The standard flanges can be turned intoany desired position. Additional sealings usually arenot necessary. For installation please observe thefollowing :
1) Prior to the installation of the expansion jointensure that the mating flanges have satisfactorysealing surfaces.Pro truding pipe ends, grooves and tongues arenot permitted as the sealing surface of thebellows might be destroyed. (see hints for thepipework designer, page 1-38)
Attention: When using slip-on flanges theoutside diameter must be larger than thesealing surface of the expansion joint.
2) Pay attention to the correct installation length: Thepulling of expansion joints into installation gapswhich are too large will lengthen the rubber bellowand might lead to the collar being drawn out of theflange groove (see picture). During the subsequenttightening of the screws the collar of the bellowswould be crushed asymmetrically.
Please note : A considerable lengthening duringinstallation decreases the allowable range ofmovement during operation. To shorten installationgaps, distance flanges are available.
3) If possible install the expansion joints in such waythat the date of production is visible.
4) Screws should be inserted from the expansionjoint side. If this is not feasible, it must beassured that the bellows may not touch thescrews in all operating conditions.
5) We recommend to use bolts of property class8.8. The bolts have to be fastened crosswise in 3uniform steps.
When using a torque wrench:
1st step: Tighten bolts equally by hand (pay attention toparallel sealing surfaces!).
2nd step: Fasten crosswise with torque 50 Nm.
3rd step: Fasten crosswise
approx. torqueup to DN 80 max. 80 Nm up to DN 300 max. 100 Nm up to DN 500 max. 130 Nm
DN 700 250 NmDN 800 300 NmDN 900 310 NmDN 1000 340 Nm
Do not use any sharp-edged tools which mightdamage the rubber bellow in case the tool slips.
6) If no torque wrench can be used duringinstallation, the screws may only be tightened toan extent that between the metal flanges adistance "y" of at least 1 mm remains (seepicture).
7) The test pressure of a bellow or flange is 1.5 xPN. This value depends on which component isweaker.
8) The rubber bellow of the expansion joint must notbe painted ! Solvents can damage the rubber cover,furthermore the colour coat impedes a propervisual inspection.
9) When welding and cutting, the rubber bellow mustbe protected against heat by all means. Forelectric welding it must be insured that the electriccurrent does not pass through the bellows.
10) Permanent radiation heat above 90° C must beavoided. If necessary flame protection coversshould be used (see page 1-37).
11) Rubber expansion joints are subject to wear andmust be included to routine inspection of the pipesystem (visual inspection of the expansion jointregarding damages as well as inspection forhardening by pushing in with a thumb).
y = min. 1 mm
installation > EL max.
wrong
correct
installation ≤ EL max.
Note: the bellowsmay not touch the
screws in alloperating conditions
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
1 -40 FlexEJ copyright 2011- R3/11
Information concerning the Pressure Equipment Directive (PED) 97/23/EC for ERV Rubber Expansion Joints
Elaflex rubber expansion joints are 'pressure equipment' according to this directive. Below we list those expansion joints which fall under category I-III:
1. Expansion joints for L.P. Gas (liquefied gases):
up to DN 40 - PN 25 bar = category Ifrom DN 50 up to DN 100 - PN 25 bar = category II
2. Expansion joints for liquid chemicals and petroleum based products:
up to DN 125 up to 16 bar working pressure = no categoryDN 150 up to 10 bar working pressure = no categoryDN 200 up to 10 bar working pressure = no categoryDN 250 from 8 up to 10 bar working pressure = category IDN 300 from 7 up to 10 bar working pressure = category IDN 350 from 6 up to 10 bar working pressure = category IDN 400 from 5 up to 10 bar working pressure = category IDN 500 from 4 up to 10 bar working pressure = category IDN 600 from 3,5 up to 10 bar working pressure = category IDN 700 from 3 up to 10 bar working pressure = category IDN 800 from 2,5 up to 10 bar working pressure = category IDN 900 from 2 up to 10 bar working pressure = category IDN 1000 from 2 up to 10 bar working pressure = category I
3. Expansion joints for gas / natural gas:
If the expansion joint is intended for use with gas / natural gas, this has to be stated when ordering.up to DN 25 = no categoryfrom DN 32 up to DN 50 - PN 16 bar = category Ifrom DN 65 up to DN 125 - PN 16 bar = category IIfrom DN 150 up to DN 350 - PN 10 bar = category IIfrom DN 400 = category III (special inquiry necessary)
4. Expansion joints for air:
If the expansion joint is intended for the use with air, this has to be stated when ordering.up to DN 100 up to 10 bar working pressure = no categoryfrom DN 125 up to DN 250 up to 5 bar working pressure = no categoryfrom DN 250 up to DN 1000 up to 3,5 bar working pressure = category I
To define the right category for all dangerous fluids or pressures not mentioned here, an inquiry is necessary. Pleasestate medium, dimension, pressure, temperature and application.
Requirements:
' no category ' These expansion joints do only have to conform to 'sound engineering practice' (SEP). Nodeclaration of conformity *) is necessary. For these expansion joints the CE marking must notbe used.
' category I ' A certificate of conformity for the materials (at least EN 10204-2.2), a random pressure test,a declaration of conformity and a CE marking of the expansion joints are necessary.
' category II ' A specific test report for the materials (at least EN 10204-3.1, the pressure test of every joint,the declaration of conformity*) and a CE marking of the expansion joint with code number ofthe notified body etc. are necessary.
The manufacturer of the expansion joints is responsible for the adherence to these requirements. Rubber bellowsor flanges alone are no pressure equipment according to this directive.
For the manufacturing of expansion joints ELAFLEX has been certified by Germanischer Lloyd. A copy of thecertificate no. 77 314 - 10 HH is available on request.
*) Declarations of Conformity:
According to the PED, ELAFLEX customers may directly download the necessary declarations of conformity.Please use this free service under www.flexej.co.uk
SeniorFlex - Commercial Quality primarily applied inHVAC applications. Bellows available in EPDM with PNflanges in zinc plated carbon steel.
FSF Type 15
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
Nom o/a Axial Axial Lateral Angular Max Max VacuumBore Length Comp Extension Pressure Temp Rating
mm mm mm mm ° Bar@ 20°C °C mm Hg
32-11/4" 130 30 20 20 35 16 95 400
40-11/2" 130 30 20 20 35 16 95 400
50-2" 130 30 20 20 35 16 95 400
65-21/2" 130 30 20 20 30 16 95 400
80-3" 130 30 20 20 30 16 95 400
100-4" 130 30 20 20 25 16 95 400
125-5" 130 30 20 20 25 16 95 400
150-6" 130 30 20 20 15 16 95 400
200-8" 130 30 20 20 15 16 95 400
250-10" 130 30 20 20 10 16 95 400
300-12" 130 30 20 20 10 16 95 400
FSF Type 15 Range
Working pressure deration with temperature
Max Pressure Bar@ Temp Temp°C
16 20
14 75
11 85
6 95
Structure
Item# Part Materials
1 Body EPDM Rubber
2 Reinforced Nylon Type Chord
3 Wire Hard Steel Wire
4 Flange Mild Steel, Galvanised Various drilling available
FlexEJ copyright 2011- R3/11 2 -1
Section
2Rubber Expansion Joints
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
2 -2 FlexEJ copyright 2011- R3/11
SeniorFlex - Commercial Quality primarily applied in HVACapplications. Bellows available in EPDM with PN flanges in zincplated carbon steel.
FSF Type 10Nom o/a Axial Axial Lateral Angular Max Max VacuumBore Length Comp Extension Pressure Temp Rating
mm mm mm mm ° Bar@ 20°C °C mm Hg
32-11/4" 95 8 4 8 15 16 95 400
40-11/2" 95 8 4 8 15 16 95 400
50-2" 105 8 5 8 15 16 95 400
65-21/2" 115 12 6 10 15 16 95 400
80-3" 130 12 6 10 15 16 95 400
100-4" 135 18 10 12 15 16 95 400
125-5" 170 18 10 12 15 16 95 400
150-6" 180 18 10 12 15 16 95 400
200-8" 205 25 14 22 15 16 95 400
250-10" 240 25 14 22 15 16 95 400
300-12" 260 25 14 22 15 16 95 400
350-14” 265 25 16 22 15 7 95 400
400-16” 265 25 16 22 15 7 95 400
450-18” 265 25 16 22 15 7 95 400
500-20” 265 25 16 22 15 7 95 400
600-24” 265 25 16 22 15 7 95 400
Rubber Expansion Joints FSF Type 10
Working pressure deration with temperature
Max Pressure Bar@ Temp Temp°C
16 20
14 75
11 85
6 95
Structure
Item# Part Materials
1 Body EPDM Rubber
2 Reinforced Nylon Type Chord
3 Wire Hard Steel Wire
4 Flange Mild Steel, Galvanised Various drilling available
Nom o/a Axial Lateral Angular Max Max VacuumBore mm Length Comp Extension Pressure Temp RatingBSPsize mm mm mm mm ° Bar@ 20°C °C mm Hg
15- 1/2" 200 22 5 22 45 10 95 400
20- 3/4" 200 22 6 22 45 10 95 400
25-1” 200 22 6 22 45 10 95 400
32-11/4" 200 22 6 22 40 10 95 400
40-11/2" 200 22 6 22 40 10 95 400
50 / 2” 200 22 6 22 45 10 95 400
65-21/2" 240 22 6 22 45 10 95 400
80 / 3” 240 22 6 22 45 10 95 400
SeniorFlex - Commercial Quality primarily applied inHVAC applications. Bellows available in EPDM with PNflanges in zinc plated carbon steel.
FTU Type 30
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FTU Type 30 Range
Working pressure deration with temperature
Max Pressure Bar@ Temp Temp°C
10 20
8 75
7 85
6 95
Structure
Item# Part Materials
1 Body EPDM Rubber
2 Reinforced Nylon Type Chord
3 Coupling Cast Ductile Iron
4 Ring Galvanised Steel
FlexEJ copyright 2011- R3/11 2 -3
Section
2Rubber Expansion Joints
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
DN DN Max Pr Compr Extens Lat.(mm) (in) +/-
100 4125 5 30150 6200 8250 10 15 20300 12
35350 14400 16 10450 18500 20600 24
40650 26700 28800 32900 361000 40 20 251050 421100 44 451200 48 81300 521400 561500 601600 641800 72 62000 802100 842200 88 50 25 302400 96 42600 1042700 1082800 112
33000 120
DN DN OD Rubber Flange F to F(mm) (in) Thickness Thickness
100 4 229125 5 254 150150 6 285200 8 343250 10 406 12 10300 12 483 200350 14 533400 16 597450 18 640500 20 715600 24 840650 26 870
250
700 28 927800 32 1060 15900 36 11681000 40 1289 151050 42 13461100 44 1403 3001200 48 15111300 52 16261400 56 16851500 60 1854 201600 64 19301800 72 21972000 80 23452100 84 25342200 88 2555 3502400 96 2877 202600 104 2960 252700 108 32192800 112 31803000 120 3562
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
SA
FET
EC
H
Section
3
The FLEXEL CG-21 is an arch-type single bellow expansion joint.
Its construction allows it to maintain a very short distance betweenflanges and it only needs a small free space for installation.
The special characteristic of these expansion joints is that they arefabricated with the flanges already integrated in the rubber body, asan enlargement of the same, and they may be made with one ormore corrugations.
The body is fabricated with rubber and fabric, and reinforced withmetal rings or steel cord. The rubber flange has enough thicknessto eliminate the need for gas-tight gaskets. The rubber flanges andthe steel back –flanges are drilled according to the customer’sspecification.
These expansion joints are fully engineered to order and thereforethe distance between flanges may vary depending on the existingspace conditions.
Larger diameters and side branches can be supplied.
Type FLEXEL CG-21
2011
FlexEJ copyright 2011- R3/11 3-1
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
3 -2 FlexEJ copyright 2011- R3/11
It is not advisable to use multi-arch expansion jointswith more than four bellows for horizontal installations.This is to maintain the lateral stability of the element.
Type FLEXEL CG-22
Type FLEXEL CG-23
DN O D Rubber Flange F to F Pr Max Compr Extens Lat. +/-(mm / in) Thickness Thickness
100 / 4 229
125 / 5 254 250 60
150 / 6 285
200 / 8 343
250 / 10 406 12 10 30
300 / 12 483 70
350 / 14 533 40
400 / 16 597 350 10
450 / 18 640
500 / 20 715
600 / 24 840
650 / 26 870 80
700 / 28 927 15
800 / 32 1060 450
900 / 36 1168
1000 / 40 1289 15 40 50
1050 / 42 1346
1100 / 44 1403 90
1200 / 48 1511 8
1300 / 52 1626
1400 / 56 1685 20
1500 / 60 1854
1600 / 64 1930
1800 / 72 2197 500 6
2000 / 80 2345
2100 / 84 2534
2200 / 88 2555
2400 / 96 2877 20 4 100 50 60
2600 / 104 2960 25
2700 / 108 3219
2800 / 112 318033000 / 120 3562
The Flexel CG-22 is an arch-type expansion joint with adouble bellow. It is especially designed for movementsthat a single bellow expansion joint cannot absorb.
Available materials for the CG range
Colour Material Main Applications Max Temp
Black Neoprene See water, Water cooling systems 90°C
Red E.P.D.M Mud, slurry 100°C
Orange E.P.D.M HT Ashes, cement plants 130°C
Yellow Nitrile Resistant to oil and gas 90°C
Green Hypalon Strong acids, except for nitric acid or sulphuric acid 100°C
Purple Viton High temp, petroleum derivatives, strong acids 180°C
White Nitrile Food conduction, potable water supply 80°C
Typical cross section CG-21
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-1
Copper Axial Expansion JointSection
4
SpecificationFlexEJ Small bore Copper ended axialexpansion joints are made from stainless steelconvoluted bellows for use in heating circuits.Designed to EJMA*.
MaterialsBellows: 316 Stainless SteelCopper Ends: BS EN1057 Table ‘X’
Operating ConditionsMax Working Pressure: 6 BarTesting Pressure: 9 BarMax Working Temp: 90oC
Application
FlexEJ Small bore Copper ended expansionjoints are used in small bore pipe work systemsto absorb thermal movement in the axialdirection.
Performance
Movements and pressure ratings apply fortemperatures up to 90oC. Copper pipe endedunits should not be used above thistemperature.
Installation
Take care when installing the bellow to ensureno torsion is applied. The unit is supplied atextended length so no cold pull is required. The bellow can be installed in any flowdirection. These expansion joints require thepipe work to be suitably anchored and guidedfor correct installation. Take care whensoldering or brazing to ensure no soldering fluxcomes into contact with the bellowconvolutions. Doing so could cause acorrosive chemical reaction and prematurefailure. DO NOT USE BELLOWS TOCORRECT FOR MISALIGNMENT OF PIPING.Refer FlexEJ bellows installation manual forfurther details.
*EJMA – Expansion Joint Manufacturers Association
Part No. DN Supplied Axial Spring Effective Force to Pressure PressureLength Move’t Rate Area Compress Rating Thrust
(comp) (6 Bar)
mm mm N/mm cm2 KgF Bar g KgF
MRCA12X200X6X25 15 200 25 19.1 5.2 49 6 31
MRCA20X210X6X25 20 210 25 19.1 5.2 49 6 31
MRCA25X215X6X25 25 215 25 26.2 8.2 67 6 50
MRCA32X225X6X25 32 225 25 28.5 13.7 73 6 82
MRCA40X230X6X25 40 230 25 35.2 20.4 90 6 123
MRCA50X230X6X25 50 230 25 59.8 32.1 153 6 193
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -2 FlexEJ copyright 2011- R3/11
Union Ended Axial Expansion Joint
SpecificationFlexEJ Union end axial movement expansionjoints come with a BSP union swivel at bothends complete with fibre washer and steelconvoluted bellows. Designed to EJMA*.
MaterialsBellows: 316 Stainless SteelUnion Ends: EN 10242 Female Union Black
Operating ConditionsMax Working Pressure: 6 BarTesting Pressure: 9 BarMax Working Temp: 150oC
Application
FlexEJ Union Ended expansion joints are used insmall bore pipe work heating systems to absorbthermal movement, in the axial direction.Malleable iron union ends allow the expansionjoint to be installed quickly and easily.
Performance
Movements and pressure ratings apply fortemperatures up to 150oC
Installation
Take care when installing the bellow to ensureno torsion is applied. The unit is supplied atextended length so no cold pull is required.The bellow can be installed in any flowdirection. These expansion joints require thepipe work to be suitably anchored and guidedfor correct installation. DO NOT USEBELLOWS TO CORRECT FORMISALIGNMENT OF PIPING. Refer FlexEJ bellows installation manual forfurther details.
*EJMA – Expansion Joint Manufacturers Association
Part No. DN Supplied Axial Spring Effective Force to Pressure PressureLength Move’t Rate Area Compress Rating Thrust
(comp) (6 Bar)
mm mm N/mm cm2 KgF Bar g KgF
MRUA12X181X6X25 15 181 25 19.1 5.2 49 6 31
MRUA20X187X6X25 20 187 25 19.1 5.2 49 6 31
MRUA25X191X6X25 25 191 25 26.2 8.2 67 6 50
MRUA32X207X6X25 32 207 25 28.5 13.7 73 6 82
MRUA40X215X6X25 40 215 25 35.2 20.4 90 6 123
MRUA50X229X6X25 50 229 25 59.8 32.1 153 6 193
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-3
Flanged Axial Expansion JointSection
4
SpecificationFlexEJ flanged axial movement expansion jointwith fixed carbon steel raised face flanges drilledto EN1092-1 PN16, multi-ply stainless steelconvoluted bellows. Designed to EJMA*.
MaterialsBellow: 316 Stainless SteelSleeve: 316 Stainless SteelFlange: EN 1092-1 PN16
Operating ConditionsMax Working Pressure: 16 BarTest Pressure: 24 BarMax Working Temperature: 300oC
Application
FlexEJ Flanged expansion joints are used insteel pipe work systems to absorb thermalmovement, in the axial direction. It also reducesnoise and vibrations from pumps andreciprocating machinery.
Performance
Pressure de-rating factors apply at elevatedtemperature.
Installation
Take care when installing the bellow to ensureno torsion is applied. The orientation of thebolt holes must be aligned with mating pipework flanges so that torsion is not introduced.The correct length of bolts is essential toensure they do not come into contact with thebellow convolutions. Take care not to causedamage to the bellow convolutions whentightening the bolts. The bellow is providedwith an internal flow liner so note the directionof flow when installing. The unit is supplied atextended length so no cold pull is required.These expansion joints require the pipe workto be suitably anchored and guided for correctinstallation. DO NOT USE BELLOWS TOCORRECT FOR MISALIGNMENT OF PIPING.Refer FlexEJ bellows installation manual forfurther details.
*EJMA – Expansion Joint Manufacturers Association
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -4 FlexEJ copyright 2011- R3/11
Flanged Axial Expansion Joint
Technical Data
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-5
Expansion Joints - MetallicSection
4
FlexEJ design and manufacture metallic expansion joints basedon the requirements of our customers.
Please contact us to discuss your application.
Axial
NB Movement Length (L) Spring ratemm +/- mm N/mm
50 25 208 40
65 25 208 75
80 25 208 99
100 25 208 130
125 38 314 238
150 38 314 226
200 50 352 232
250 50 352 247
300 50 352 256
Scope: Rating:
PN Flanges carbon steel Maximum Working Pressure 16 Barg
Bellows 321 Stainless Steel Test Pressure 24 Barg
Temperature Range -20 / +120° C
EJMA Cycle 1000
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -6 FlexEJ copyright 2011- R3/11
Expansion Joints - Metallic
FlexEJ design and manufacture metallic expansion joints based on therequirements of our customers.
Please contact us to discuss your application.
Lateral
NB Movement Length (L) Spring ratemm +/- mm Nmm
50 75 1000 1
65 75 1000 1
80 75 1000 2
100 75 1000 4
125 75 1000 6
150 75 1000 8
200 75 1000 17
250 75 1000 33
300 75 1000 66
Scope: Rating:
PN Flanges, carbon steel Maximum Working Pressure 16 Barg
Bellows 321 Stainless Steel Test Pressure 24 Barg
Tie rods and spherical washers Temperature Range -20 / +120° C
EJMA Cycle 1000
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-7
Expansion Joints - MetallicSection
4
FlexEJ design and manufacture metallic expansion joints basedon the requirements of our customers.
Please contact us to discuss your application.
Hinge
NB Movement Length (L) Spring ratemm +/- mm Nm/ o
50 5 100 1.7
65 5 110 3.7
80 5 120 6.2
100 5 140 8.7
125 6.5 206 19.7
150 6.5 200 23.4
200 7 222 36.5
250 3.5 220 98
300 3.5 220 121
Scope: Rating:
PN Flanges, carbon steel Maximum Working Pressure 16 Barg
Bellows 321 Stainless Steel Test Pressure 24 Barg
Hinges, carbon steel Temperature Range -20 / +120° C
EJMA Cycle 1000
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -8 FlexEJ copyright 2011- R3/11
Expansion Joints - Metallic
FlexEJ design and manufacture metallic expansion joints based on therequirements of our customers.
Please contact us to discuss your application.
Gimbal
NB Movement Length (L) Spring ratemm +/- mm Nm/ o
50 5 100 1.7
65 5 110 3.7
80 5 120 6.2
100 5 140 8.7
125 6.5 206 19.7
150 6.5 200 23.4
200 7 222 36.5
250 3.5 220 98
300 3.5 220 121
Scope: Rating:
PN Flanges, carbon steel Maximum Working Pressure 16 Barg
Bellows 321 Stainless Steel Test Pressure 24 Barg
Gimbal, carbon steel Temperature Range -20 / +120° C
EJMA Cycle 1000
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-9
Expansion Joints - Installation InstructionsSection
4
Pre-Installation Checks and PrecautionsFlexEJ Expansion Joints are fully inspected at the factory and are packaged to arrive at the job site in goodcondition. Please, immediately upon receipt at the job site, verify that there is no freight damage; i.e., dents,broken hardware, loose shipping bars, etc.
Because the bellows expansion joint is required to absorb thermal and/or mechanical movements, the bellowselement must be constructed of a relatively thin material. This requires special installation precautions. Thefollowing steps should be taken prior to installation of the expansion joint into the pipeline or duct.
1. The opening into which the expansion joint will be installed should be examined to verify that the opening forwhich the expansion joint was designed does not exceed the installation tolerances designated by thedesigner and/or purchaser. If the opening exceeds the tolerance, notify FlexEJ at once for a disposition.
2. The attachment edges of the pipe or duct should be smooth, clean, and parallel to each other.
3. The area around the expansion joint should be cleared of any sharp objects or protrusions. If not removable,they should be noted so they can be avoided.
4. Expansion joints provided with lifting lugs should be lifted only by the designated lifting lugs. SHIPPINGBARS (PAINTED YELLOW) ARE NOT DESIGNED TO BE LIFTING DEVICES. NEVER USE A CHAIN OR ANYOTHER HANDLING DEVICES DIRECTLY ON THE BELLOWS ELEMENT OR BELLOWS COVER. Forexpansion joints not provided with lifting lugs (i.e. less than 200 Kgs) the best lifting method should beevaluated at the time of installation.
5. The shipping bars are installed on an expansion joint to maintain shipping length and give the expansionjoint stability during transit and installation. DO NOT REMOVE THE SHIPPING BARS UNTIL THEINSTALLATION IS COMPLETE.
InstallationThe unrestrained Axial Expansion Joint must only be used in straight line pipe runs that have beenADEQUATELY ANCHORED AND GUIDED. The Axial Expansion Joint may be positioned anywhere in a straightpipe run. However, the number of anchors, primary and intermediate guides required varies, so it is importantto carefully assess the options available on site. When installing an expansion joint the following precautionsmust be taken:
1. Remove any protective covering from the ends of expansion joint. Plywood covers may have been used toprotect flanges or weld ends. Check inside expansion joint for desiccant bags or any other material.
2. When a flow liner is installed in the expansion joint, orientate the expansion joint with FLOW ARROWPOINTING IN DIRECTION OF FLOW.
3. When using lifting lugs, lift the joint to desired location and position into pipeline or ducting.
4. Weld/Soldered End Expansion Joints.
4.1PRIOR TO WELDING/SOLDERING, COVER THE BELLOWS ELEMENT WITH A CHLORIDE FREE FIRERETARDANT CLOTH. This is to prevent arc strikes, weld splatter, etc. from damaging the bellows element.
4.2 Using the proper electrode/flux, weld the expansion joint to adjacent piping. DO NOT USE BELLOWS TOCORRECT FOR MISALIGNMENT OF PIPING UNLESS THIS HAS BEEN CONSIDERED IN THE DESIGN OFTHE EXPANSION JOINT.
5. Flanged End Expansion Joints.
5.1 Orientate expansion joint flanges so that the bolt holes are aligned with the mating flanges. DO NOT FORCE THE EXPANSION JOINT TO MATCH THE BOLT HOLES OF THE MATING FLANGE. This causes torsion on the bellows and will severely reduce the bellows capability during operation and may cause premature failure of the expansion joint. It is good practice to leave one pipe flange looseuntil the expansion joint is installed or to purchase an expansion joint with a flange that will rotate.
5.2 Install gaskets and bolt to the required torque recommended by the flange manufacturer.
6. Union End Expansion Joints - Take great care when fitting screwed end expansion joints not to apply anytorsion to the bellows. Expansion joints are damaged very easily when torque. Always use a full Union atboth ends.
FLEXEJ LIMITED WARRANTY IS VOID UNLESS THE ABOVE INSTRUCTIONS ARE FOLLOWED
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -10 FlexEJ copyright 2011- R3/11
Expansion Joints - Installation Instructions
Pipe Anchors & Guides
Straight pipe runs when compensated by unrestrained axial expansion joints tend to buckle under the influence of both,the internal pressure acting on the bellows and/or the flexibility of the bellows itself. They can also buckle under theinfluence of the pressure thrust developed by the bellows, which loads the pipe axially and causes it to act like a straightbeam subjected to compressing axial forces. Besides proper supporting of the pipeline for weight and external forces, itis of vital importance that the correct alignment of the pipe is maintained to ensure the proper functioning of theexpansion joints. Using a proper guiding system, which shall follow the rules given below, can control the risk ofbuckling:
Rule A: The piping system has to be sectionalised by means of fixed points, anchors and guides. Only one expansionjoint must be fitted per section of straight line.Rule B: The pipe anchors and other restraining devices shall be designed for the full pressure thrust acting on theeffective area of the bellows, plus the bellows spring reaction load. The friction loads generated by the type ofguide/support should also be considered for each section of pipe between anchors.
Axial expansion joints not restraining the pressure thrustL1< 4 D, L2<14 DLf minimum possibleLg, the maximum distance between two guides at any conditions shall be limited to:
Where:E, is the modulus of elasticity of the pipe materialJ, is the moment of inertia of the pipe cross section
With the mean diameter, D3mp, of the pipe and, e, its wall thickness
S, is the safety factor (recommended: S = 3)Fi, is the buckling force consisting of the following components, which may act on the pipe simultaneously:
Fi = Fp + FB + FF,
Where:Fp = p.a is the pressure thrust.The bellows effective area a is given in the FlexEJ data sheets.
FB = ± X.KB is the axial displacement force generated by the bellowsThe axial displacement, X, of the expansion joint is measured from the neutral axis position. It is positive forcompression and negative for extension. The spring rating, KB, is given in the FlexEJ data sheets.
FF = ± ∑µ.FN defines the friction forces in the pipe guide.
FLEXEJ LIMITED WARRANTY IS VOID UNLESS THE ABOVE INSTRUCTIONS ARE FOLLOWED
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 4-11
Expansion Joints - Installation InstructionsSection
4
FLEXEJ LIMITED WARRANTY IS VOID UNLESS THE ABOVE INSTRUCTIONS ARE FOLLOWED
All the singular forces bring by every guide between on a section of straight run have to be taken inconsideration to calculate the friction axial force. These friction forces will occur when the system ismoving, mainly when the temperature changes or for any other matter. The value of, µ, which is the frictioncoefficient in the guides and supports is given by the support manufacturer and the vertical load, FN,which are mainly weight loads are given by the pipe stress analysis.
Rule C: When on the same straight pipe run, an axial expansion joint is located adjacent to a pipe reducer.The loads on the small diameter anchors will have to take into account the full pressure thrust of theexpansion joint. Consideration should be made for eccentric pipe reducers and the effect of an offset load(l).
Single axial expansion joint located on the large diameter side of a reducer
Rule D: The pipe shall be guided in such a way that no lateral or angular movements allowed for in the pipe stress analysis or in the expansion joint design, can occur. For small diameters, the guideshave to be spaced in such a way so that snake behaviour of the line can be avoided. To allow free straightmovements of the pipe, the supporting devices of the system shall be designed to reduce the friction andthe risk of binding in the guides.
Single axial expansion joint on a pipe run containing an offset
This application shall be avoided because the pressure thrust developed by the bellows and the frictionforces due to the thermal expansion will introduce a moment in the piping, which may result in anoverstressing of the piping and of the guides.
Pipe Guide Spacing Table
NOTES:
FlexEJ recommends that for ABS, ABSC, ANW, ANF, ANL, UNW, UNF type Bellows Expansion Joints thefirst guide be located within four (4) pipe diameters from the expansion joint and the second guide belocated within a distance of fourteen (14) pipe diameters from the first guide. The remaining guides are tobe in accordance with the table below.
The table on the next page shows the recommended MAXIMUM Spacing of Intermediate Pipe Guides forApplications Involving Axial Movement Only. (Values Based on Standard Weight of Carbon Steel Pipe.)
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
4 -12 FlexEJ copyright 2011- R3/11
Expansion Joints - Installation Instructions
FLEXEJ LIMITED WARRANTY IS VOID UNLESS THE ABOVE INSTRUCTIONS ARE FOLLOWED
After Installation But Prior To The Hydro TestPre-Test Checks1. Inspect entire system to insure that anchors, guides and pipe supports are installed in strict accordance with
piping system drawings. A pipe guide spacing chart is provided on the previous page to aid in this check.
2. ANCHORS MUST BE DESIGNED FOR THE TEST PRESSURE THRUST LOADS. Expansion joints exert aforce equal to the test pressure times the effective Area of the bellows during hydro test. Pressure thrust atdesign pressure may be found on the individual drawings. Refer to EJMA Safety Recommendations.
3. If the system media is gaseous, check to determine if the piping and/or the expansion joint may requireadditional temporary supports due to the weight of water during testing.
4. REMOVE SHIPPING BARS (PAINTED YELLOW) PRIOR TO HYDROTESTING. Shipping bars are notdesigned for hydrostatic pressure thrust loads.
5. Hydrostatically test pipeline and expansion joint. ONLY CHLORIDE FREE WATER SHOULD BE USED FORHYDROTEST (published reports indicate chloride attack as low as 3 PPM). Water should not be left standingin the bellows.
General Precautions1. Cleaning agents, soaps and solvents may contain chlorides, caustics, or sulfides and can cause stress
corrosion which appears only after a bellows is put into service.
2. Wire brushes, steel wool and other abrasives should not be used on the bellows element.
3. Hydrostatic test pressure should not exceed 1.5 times the rated working pressure unless the expansion jointwas specifically designed for this test pressure.
4. Some types of insulation leach chlorides when wet. Only chloride free insulation materials should be used forinsulating an expansion joint.
For all other pipe sizes refer to the Standards of The Expansion Joint Manufacturers Association.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 5-1
FLEXIBLE HOSES TYPE FBH SERIES EPDM RUBBER FANCOIL HOSE
Section
5
2011
DESIGN CONDITIONS MATERIALS OF CONSTRUCTION IDENTIFICATION
Max. Working Pressure 15.0 Bar Hose EPDM (KTW & WBC approved) Manufacturer, Nom Bore, Temperature Rating - 20.0 / +110.0 ˚C Outer Braid 304 Stainless Steel Country of origin, Max. Test Pressure 30.0 Bar Ferrules Stainless Steel Date of manufacture, Guarantee 10 Years Fittings Nickel Plated Brass Type No.
SPECIFICATION
FlexEJ type FBH fancoil hose manufactured from EPDM rubber with stainless steel outer braid and nickel plated brassend fittings.
End fittings attached by swaged stainless steel ferrules. Refer to next page for end fitting options.
ALL FLEXEJ TYPE FBH HOSES ARE SUPPLIED WITH A MANUFACTURERS 10 YEAR GUARANTEE.
N.B. Please note that all pressure ratings are affected by the length of each assembly and the liquids & inhibitors thatmay be being used. The above ratings are guidelines only and should be verified prior to installation.
TYPICAL APPLICATIONSFBH EPDM hoses are designed to allow maximum flexibility for misalignment of pipe work and vibration isolation fromFancoil units and are suitable for heating and chilled water systems. The EPDM lining is ageing resistant in heatingsystems. Due to the flexibility of this range of hoses, special care must be taken during installation - always refer to theinstallation guide prior to installation.
ACCESSORIESFBH hoses can be provided with vapour sealed Armaflex Class ‘O’ insulation when required on chilled waterapplications.
TECHNICAL DATA
NOMINAL HOSE HOSE MIN.LENGTH MIN.LENGTH PRESSURE PRESSUREBORE LENGTH I/DIA 90˚ BEND 180˚ BEND RATING 65˚C RATING 20˚C
mm mm mm mm Bar Bar
30013 (1/2”) 450 13.0 258 352 6.0 15.0
600
30020 (3/4”) 450 19.0 344 470 6.0 12.0
600
30025 (1”) 450 25.0 423 580 6.0 10.0
600
Flexible Hose End Fitting Options (HVAC)
END FITTING OPTION DESCRIPTION NOMINAL BORE
CF Compression Fitting 10, 12, 15c/w Brass Nut and Olive 22 & 28mm
CF Swivel Female Nut 1/2”, 3/4”, 1”c/w Cone Seat
PF Nickel Plated Brass 10, 12, 15'PUSHFIT' & 0022mmc/w John Guest, Tectite,or other fittings
F Swivel Female Nut 1/2”, 3/4”, 1”c/w Flat Face Seat& Fibre Washer
P 35mm Long Brass 10, 12, 15Standpipe end 22 & 25mmTo suit copper fittings
PM Fixed Male 1/2”, 3/4”, 1”c/w Parallel Thread
M Fixed Male 1/2”, 3/4”, 1”c/w BSP Taper Male
F 90˚ Elbow with Swivel 1/2”, 3/4”, 1”Female Nutc/w Flat Face Seat& Fibre Washer
For Technical Assistance and Sales Contact: FlexEJ LtdTel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
5 -2 FlexEJ copyright 2011- R3/11
NB. Please check that the fittings you require are compatible with the bore size of hose for the specific application.
32mm & 40mm bore product details are available upon request.
Resistance and compatibility details of chemicals and fluids are available upon request.
Any variation of hose assembly can be made to meet your requirements.
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 6-1
FLEXIBLE HOSES TYPE FSH SERIES METALLIC BRAIDED FLEXIBLE HOSE
Section
6
2011
DESIGN CONDITIONS MATERIALS OF CONSTRUCTION IDENTIFICATION
Max. Working Pressure To suit specific Hose 321 / 316 Stainless Steel As required acc. to P.E.D. Temperature Rating client applictions Outer Braid 304 Stainless Steel 97/23/EC Max. Test Pressure Ferrules Stainless Steel
Fittings Carbon or stainless Steel
SPECIFICATIONFlexEJ type FSH metallic flexible hose to suit client's specific pressure, temperature, movements or vibration applications.
End fittings to suit client specific requirements. Refer to next page for end fitting examples.
TYPICAL APPLICATIONSFSH metallic flexible hoses are designed to allow maximum flexibility for misalignment of pipe work, compensate forpipe line thermal expansion and vibration isolation. Due to the flexibility of this range of hoses, special care must be taken during installation - always refer to installationinstructions.
ACCESSORIESFSH hoses can be provided with vapour sealed Armaflex class 'O' insulation when required on chilled waterapplications.
TECHNICAL DATA
NOMINAL HOSE HOSE Dimms HOSE Dimms MIN.BEND PRESSURE Number ofBORE LENGTH I/Dia O/Dia RADIUS RATING 20˚C Outer Braids
mm mm mm mm Bar
6 (1/4”)through to Unlimited Size Dependant Size Dependant Size Dependant Size Dependant Size and250 (10”) Refer to sheet Refer to sheet Refer to sheet Refer to sheet Pressure
6-4 and 6-5 6-4 and 6-5 6-4 and 6-5 6-4 and 6-5 Dependant
Typical Flexible Hose End Fitting Options (HVAC)
END FITTING OPTION DESCRIPTION NOMINAL BORE
CF Compression Fitting 13, 20, 25c/w Brass Nut and Olive
1/2”, 3/4”, 1”
SCF Swivel Female Nut 13, 20, 25c/w Cone Seat
1/2”, 3/4”, 1”
PF Nickel Plated Brass 13'PUSHFIT'c/w John Guest, Tectite, 1/2”OR other fittings
SFF Swivel Female Nut 13, 20, 25c/w Flat Face Seat
1/2”, 3/4”, 1”
SP 25mm Long Brass 13, 20, 25Stub pipe endTo suit copper fittings 1/2”, 3/4”, 1”
PM Fixed Male 13, 20, 25c/w Parallel Thread
1/2”, 3/4”, 1”
TM Fixed Male 13, 20, 25c/w BSP Taper Male
1/2”, 3/4”, 1”
EF 90˚ Elbow with Swivel 13, 20, 25Female Nutc/w Flat Face Seat 1/2”, 3/4”, 1”
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
6 -2 FlexEJ copyright 2011- R3/11
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 6-3
METAL HOSE DESIGNSection
6
Sp
ecifi
catio
ns s
ubje
ct t
o c
hang
e w
itho
ut n
otic
e –
Co
pyr
ight
ELE
AFL
EX
2011
Influence of the service conditions on the metal hose designIn view of the wide variety of potential applications the workingpressures and bending radius stated in the technical tables canonly be used as a guideline. They are valid for predominantlystatic stress and room temperature (20 °C). The bursting pressureof the hoses is a factor of 4X greater than the working pressurestated in the tables. The maximum allowable testing pressure is1.5X the working pressure. The actual service conditions (i.e.pulsating and discontinuous demand, type and frequency ofmotion, higher working temperature etc) exert additionaldemands on the hose material. These influences must be takeninto account when determining the safe working and working lifeof the hose assemblies using the tables and formulae given here.
Single motionMinimum bending radius for single motion tested according toISO 10380 7.4.2 - picture 2.
Repeated motionFor repeated motion without major dynamic demand.
Dynamic motionFor dynamic motion the radius Rb is to be re-calculatedaccording to the table with the help of the corrective factors ftand fdyn.
The allowed working pressure is calculated as follows:
Ptoel. = Pmax. .ft .fdyn
Ptoel. = Allowed (bar) working pressure
Pmax = Max. working (bar)pressure acc. to table
ft = Reduction factor for (without dimensions)increased temperature
fdyn. = Reduction factor for (without dimensions)dynamic demand
The allowed bending radius is calculated as follows:
Rdyn. = Bending radius for (mm)dynamic demand
Rb = Bending radius for (mm)repeated motion acc. to table
ft = Reduction factor for (without dimensions)increased temperature
fdyn. = Reduction factor for (without dimensions)dynamic demand
Rdyn. = Rb (1,09 + ft .fdyn. +1 + 1 )____ __ ____
2,98 ft fdyn.
UFBX DN 6 - DN 200
UFC DN 6 DN 80
Stainless steel hose, annular corrugations
Design UFBX / UFC 0 UFBX / UFC 1 UFBX / UFC 2
Corrugated hose Corrugated hose Corrugated hose
without braiding with one braiding with two braidings
Material No. Austenitic, stainless steel
Hose Braiding
(BS 1449 Part 2) (BS 1554)
321S31/ similar to AISI 321 304S31/316S11 / similar to AISI 316 L similar to AISI 304
Other materials available on request
Temperature usable from -200°C to +600°C
When ordering please specify: ● Type of hose [UFBX / UFC...]● Hose material [321/316]● Nominal diameter [DN]● Total length [TL]● Number of braiding● End fittings (Type and material)● Design pressure● Working pressure● Design temperature● Working temperature
Please use correction factors for thepermissible pressure and bendingradius through increased temperatureor dynamic stress from the cataloguesheet "Design of metal hoses"
DN Type Dimensions Bend radius Max working Weight
Internal External Single Dynamic pressure
diameter diameter motion motion at 200
d1 Tol± d2 d3 Tol± Rst Rb P max (± 10%)
mm inch (mm) (mm) (mm) (mm) (mm) (mm) (mm) (bar) (kg/m)
UFBX 0 9.8 - 0.3 16 110 10.0 0.08
6 1/4" UFBX 1 7.0 0.25 - 11.5 0.4 25 110 167.0 0.16
UFBX 2 - 13.1 0.5 25 110 220.0 0.25
UFBX 0 11.8 - 0.3 20 130 10.0 0.12
8 5/16" UFBX 1 8.3 0.25 - 13.5 0.4 32 130 136.0 0.23
UFBX 2 - 15.2 0.5 32 130 210.0 0.33
UFBX 0 14.6 - 0.3 22 150 5.5 0.16
10 3/8" UFBX 1 10.3 0.25 - 16.3 0.4 38 150 100 0.27
UFBX 2 - 18.0 0.5 38 150 178.0 0.38
UFBX 0 19.3 - 0.3 24 165 5.5 0.17
12 1/2" UFBX 1 14.9 0.30 - 20.9 0.4 45 165 74.0 0.35
UFBX 2 - 22.6 0.5 45 165 103.0 0.52
UFBX 0 21.7 - 0.3 28 195 5.0 0.28
16 5/8" UFBX 1 16.3 0.30 - 23.4 0.4 50 195 70.0 0.46
UFBX 2 - 25.1 0.5 50 195 125.0 0.63
UFBX 0 25.5 - 0.3 30 200 4.1 0.27
20 3/4" UFBX 1 20.1 0.30 - 27.4 0.4 70 200 65.0 0.53
UFBX 2 - 29.3 0.5 70 200 86.0 0.79
UFBX 0 33.3 - 0.4 44 200 4.1 0.32
25 1" UFBX 1 27.4 0.40 - 35.8 0.5 85 200 50.0 0.71
UFBX 2 - 38.3 0.6 85 200 76.0 1.10
UFBX 0 40.7 - 0.4 55 250 3.4 0.40
32 1 1/4" UFBX 1 34.3 0.40 - 43.2 0.5 105 250 39.0 0.86
UFBX 2 - 45.7 0.6 105 250 57.0 1.32
UFBX 0 47.5 - 0.4 70 250 2.4 0.67
40 1 1/2" UFBX 1 39.4 0.40 - 50.0 0.5 127 250 35.0 1.19
UFBX 2 - 52.5 0.6 127 250 55.0 1.71
UFBX 0 61.7 - 0.4 90 350 1.0 0.82
50 2" UFBX 1 53.0 0.40 - 64.2 0.5 160 350 30.0 1.56
UFBX 2 - 66.7 0.6 160 350 44.0 2.29
UFBX 0 76.1 - 0.4 110 410 1.0 1.80
65 2 1/2" UFBX 1 64.3 0.40 - 78.6 0.5 200 410 26.0 2.68
UFBX 2 - 81.1 0.6 200 410 46.0 3.57
UFBX 0 89.4 - 0.4 130 450 1.0 2.21
80 3" UFBX 1 76.5 0.40 - 91.9 0.5 230 450 22.0 3.29
UFBX 2 - 94.5 0.6 230 450 40.0 4.37
UFBX 0 119.0 - 0.6 131 530 0.1 1.81
100 4" UFBX 1 100.0 0.50 - 122.6 0.7 218 530 20.0 3.89
UFBX 0 145.6 - 0.7 189 800 0.1 2.58
125 5" UFBX 1 124.9 0.60 - 150.4 0.8 315 800 20.0 6.00
UFBX 0 173.2 - 0.8 216 1050 0.1 3.55
150 6" UFBX 1 150.4 0.70 - 178.0 0.9 360 1050 23.0 8.28
UFBX 0 227.0 - 0.9 281 1300 0.1 4.75
200 8" UFBX 1 200.7 0.80 - 231.8 1.0 468 1300 15.0 10.46
Reproduction not permitted Subject to changes in design Larger diameters available on request
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
6 -4 FlexEJ copyright 2011- R3/11
UFBXStandard pitch high pressure hose with high flexibility
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
UFCClose pitch high pressure hose with high flexibility
FlexEJ copyright 2011- R3/11 6 -5
DN Type Dimensions Bend radius Max working Weight
Internal External Single Dynamic pressure
diameter diameter motion motion at 200
d1 Tol± d2 d3 Tol± Rst Rb P max (± 10%)
mm inch (mm) (mm) (mm) (mm) (mm) (mm) (mm) (bar) (kg/m)
UFC 0 13.0 - 0.3 16 100 10.0 0.20
6 1/4" UFC 1 7.0 0.25 - 14.5 0.4 25 100 171.0 0.31
UFC 2 - 15.9 0.5 25 100 305.0 0.42
UFC 0 12.0 - 0.3 20 140 10.0 0.19
8 5/16" UFC 1 8.3 0.25 - 13.4 0.4 38 140 164.0 0.41
UFC 2 - 14.7 0.5 38 140 210.0 0.29
UFC 0 17.8 - 0.3 22 150 5.5 0.29
10 3/8" UFC 1 10.3 0.25 - 19.3 0.4 40 150 151.0 0.48
UFC 2 - 20.7 0.5 40 150 260.0 0.67
UFC 0 21.8 - 0.3 24 165 5.5 0.17
12 1/2" UFC 1 14.9 0.30 - 13.3 0.4 50 165 114.0 0.35
UFC 2 - 24.7 0.5 50 165 205.0 0.52
UFC 0 26.9 - 0.3 28 200 5.0 0.37
16 5/8" UFC 1 16.3 0.30 - 28.6 0.4 50 200 90.8 0.64
UFC 2 - 30.2 0.5 50 200 163.0 0.91
UFC 0 28.0 - 0.3 30 200 4.1 0.48
20 3/4" UFC 1 20.1 0.30 - 30.2 0.4 70 200 90.8 0.86
UFC 2 - 32.3 0.5 70 200 150 1.20
UFC 0 35.0 - 0.4 40 200 4.1 0.64
25 1" UFC 1 27.4 0.40 - 37.2 0.5 90 200 79.4 1.10
UFC 2 - 39.3 0.6 90 200 120.0 1.60
UFC 0 46.5 - 0.4 55 250 3.2 1.30
32 1 1/4" UFC 1 34.3 0.40 - 48.8 0.5 108 250 59.0 2.30
UFC 2 - 50.7 0.6 108 250 89.0 3.30
UFC 0 54.5 - 0.4 70 250 2.4 1.20
40 1 1/2" UFC 1 39.4 0.40 - 56.7 0.5 127 250 46.0 1.90
UFC 2 - 58.8 0.6 127 250 71.0 2.70
UFC 0 65.5 - 0.4 90 350 1.0 1.30
50 2" UFC 1 53.0 0.40 - 68.5 0.5 175 350 40.2 2.30
UFC 2 - 70.9 0.6 175 350 50.0 3.30
UFC 0 85.5 - 0.4 110 410 1.0 2.00
65 2 1/2" UFC 1 64.3 0.40 - 88.2 0.5 200 410 35.5 3.30
UFC 2 - 90.7 0.6 200 410 50.0 4.60
UFC 0 97.7 - 0.4 130 450 1.0 2.50
80 3" UFC 1 76.5 0.40 - 100.0 0.5 200 450 28.1 4.00
UFC 2 - 103.0 0.6 200 450 50.0 5.50
Reproduction not permitted Subject to changes in design Larger diameters available on request
Correction factors for dynamic demand
Motion / *Flow Without vibration, low low vibration, frequent strong vibration,rhythmical and slow motion uniform motion ongoing motion
Stationary or slow 1,00 0,80 0,40uniform flow
Pulsating and swelling flow 0,80 0,64 0,32
Rhythmical and 0,40 0,32 0,16discontinuous flow
*An internal liner should be used when the flow velocity of the medium is exeeding the following values:-Hose without braiding : gas30m/s, liquid 15m/s-Hose with braiding: gas 45m/s, liquid 22.5m/s
Calculation example
Stainless steel corrugated hose material AISI 321 , UFBX 1 DN 50 is installed at a temperature of 263° C. It is exposed tolow vibration and frequent uniform motion with pulsating and swelling flow.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
6 -6 FlexEJ copyright 2011- R3/11
Correction Factors for Hose Systems
Rdyn. = Rb (1,09 + ft .fdyn. +1 + 1 )____ __ ____
2,98 ft fdyn.
Rdyn. = 350 (1,09 + 0.71-0.64 + 1 + 1 )____ ____ ____2,98 0.71 0.64
Pmax = 30 bar,
Rb = 350mm. ft = 0.71 fdyn. = 0,64
Ptoel.= Pmax. . ft . fdyn.
Pmax = 30 - 0.71 - 0.64
Pmax = 13.6 bar
Rdyn. = 530 mm
Temperature de-rating factors:
Temperature º C
Material -200 20 50 100 150 200 250 300 350 400 450 500 550 600 650to -20
Derating Factors
1.4306 1 1 0.89 0.72 0.64 0.58 0.54 0.5 0.48 0.46 0.44 0.43 0.43 A —SS304L
1.4301 1 1 0.9 0.73 0.66 0.6 0.55 0.51 0.49 0.48 0.46 0.46 0.46 A ASS304
1.4541 1 1 0.93 0.83 0.78 0.74 0.7 0.66 0.64 0.62 0.6 0.59 0.58 A ASS321
1.4404 1 1 0.9 0.73 0.67 0.61 0.58 0.53 0.51 0.5 0.49 0.47 0.47 A —SS316L
1.4401 1 1 0.91 0.78 0.7 0.65 0.61 0.57 0.55 0.53 0.52 0.51 0.5 A ASS316
1.4571 1 1 0.92 0.8 0.76 0.72 0.68 0.64 0.62 0.6 0.59 0.58 0.58 A —SS316Ti
NB: “A” – Refer to FlexEJ
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2007 - R1/07 6-9
Metallic Flexible Corrugated Hose Assemblies – Installation & Safety Guides
FlexEJ metallic flexible corrugated hose assemblies are designed to meet pre-defined parameters of maximumoperating conditions. It is therefore important to ensure the flexible hose assembly meets the intended serviceconditions.
Prior to placing a metallic flexible hose assembly in to service, as a minimum, consideration should be given toensuring the flexible hose assembly will meet all aspects of the application, in respect of pressure, temperature,materials compatible with intended service, bend radius requirement, flow velocity, end fitting specification and endfitting attachment method.
The known integrity of the flexible hose assembly is important to the safety of any application. If in doubt ask.
Pressure: Flexible metallic hose assemblies must not be used above their maximum design pressure.
Shock pressure: Pulsating, surge or shock pressure will affect the life of a flexible hose assembly. Such pressureconditions must not exceed 50% of the flexible hose assembly maximum rated design pressure.
Temperature: Metallic flexible corrugated hose assemblies generally provide a good design temperature range.FlexEJ stated maximum design pressures with weld (TIG) attached end fittings are based on ambient temperaturecondition. When using flexible metallic hose assemblies at temperatures above ambient condition it is important totake into consideration pressure/temperature de-rating factors – See overleaf.
Bend radius: Care should be taken to ensure the flexible hose assembly is not installed and working with a bendradius below its published minimum design bend radius. Published minimum bend radius figures cover both static andflexing installations. Failure to consider this can result in fatigue and premature failure. Avoid installations resulting insharp bending immediately behind the flexible hose end fitting.
Flow Velocity: High velocities can lead to premature fatigue failure of a corrugated flexible hose assembly. A metallicstripwound interlocking liner should be considered and introduced if flow velocity exceeds:-
• Flexible corrugated hose assembly without external braid reinforcement if gas flow exceeds 30 metres/second or in the case of liquid 15 metres/second
• Flexible corrugated hose assembly with external braid reinforcement if gas flow exceeds 45 metres/second or in the case of liquid 22.5 metres/second
When a hose assembly is installed in a bend, these values should be reduced by 50% for a 90 degree bend, 25% fora 45 degree bend and appropriately in proportion to the angle of bend.
With higher velocity the next larger bore size should be used with a stripwound liner
End Fitting Specification: Selection of the correct specification of end fitting is important to a safe application. Theend fitting should be suitable for the extremes of pressure and temperature.
End Fitting attachment: Ensure the end fitting attachment method is compatible with the application, particular theoperating temperature. Most metallic flexible corrugated hose assemblies employ weld (TIG) attachment which willperform at the higher temperature range but other attachments are used, such as, brazing (silver solder) which havelimitation on temperature performance.
Do not Torque: Flexible metallic corrugated hose assemblies must never be subjected to torque or twisting duringinstallation and application.
• To avoid this condition during installation use as a minimum a swivel end fitting at one end of the flexible hose. The fixed end should always be connected first.
• For movement applications always install the flexible hose assembly so the movement occurs in one plane only, and in the plane of bending.
Failure to apply these rules will result in premature failure.
Section
6
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
6 -10 FlexEJ copyright 2007 - R1/07
METALLIC FLEXIBLE CORRUGATED HOSE ASSEMBLIES – INSTALLATION & SAFETY GUIDES
Axial movement: Flexible corrugated hose assemblies are not designed for in-line axial movement and should not besubjected to compression or extension during application service.
Abrasion/rubbing: Do not allow flexible corrugated hose assemblies to rub on other objects or equipment. This can beparticularly damaging if the hose assembly is installed on a flexing application or being used for vibration movement.Premature and catastrophic failure can occur especially if the pressure restraining braid is damaged and weakened.
Corrosion: Correct selection of materials is important when considering flexible corrugated hose assemblies fortransferring chemicals or if used in a chemical environment.
Metallic flexible corrugated hose assemblies produced of commercial grade stainless steel materials, including 316L arenot suitable for transferring seawater or seawater contact. Premature failure caused by pitting corrosion or fatigue crackingof the corrugated flexible tube will occur.
Refer attached illustration guide for correct installation recommendations.
Maintenance, inspection and testing: Having placed in to service a well designed, manufactured and tested flexiblehose assembly, consideration should be given to on-going maintenance, inspection and testing. Depending upon theseverity of the application the life expectancy of a flexible hose assembly will be effected. Users should ensure all flexiblehose assemblies are subject to periodic inspection. As a minimum this should include a regular periodic visual inspectionto check for any wear or damage to the flexible hose that may affect its continuing service. Re-testing of hose assembliesis recommended at least annually. The test pressure should be 1.5 times the maximum working or design pressure. Whenused in arduous or safety critical applications a planned maintenance replacement programme is recommended.
Temperature de-rating factors:
Temperature º C
Material -200 20 50 100 150 200 250 300 350 400 450 500 550 600 650
to -20
Derating Factors
1.43061 1 0.89 0.72 0.64 0.58 0.54 0.5 0.48 0.46 0.44 0.43 0.43 A —
SS304L
1.43011 1 0.9 0.73 0.66 0.6 0.55 0.51 0.49 0.48 0.46 0.46 0.46 A A
SS304
1.45411 1 0.93 0.83 0.78 0.74 0.7 0.66 0.64 0.62 0.6 0.59 0.58 A A
SS321
1.44041 1 0.9 0.73 0.67 0.61 0.58 0.53 0.51 0.5 0.49 0.47 0.47 A —
SS316L
1.44011 1 0.91 0.78 0.7 0.65 0.61 0.57 0.55 0.53 0.52 0.51 0.5 A A
SS316
1.45711 1 0.92 0.8 0.76 0.72 0.68 0.64 0.62 0.6 0.59 0.58 0.58 A —
SS316Ti
NB: “A” – Refer to FlexEJ
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2007 - R1/07 6-11
Typical Installation and Operating Instructions
Correct and incorrect installation modes are shown in the following charts:
Section
6
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
6 -12 FlexEJ copyright 2007 - R1/07
TYPICAL INSTALLATION AND OPERATING INSTRUCTIONS
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 7-1
Flanged Air & Dirt SeparatorSection
7
FlexEJ Air & Dirt Separators can be used in both heating and coolingsystems to remove trapped air and dirt particles from the fluid.
The FlexEJ Air & Dirt separator is supplied with vent, drain and auto air eliminator valves.
MaterialsPipe Body & Piping: Carbon SteelFlanges: BS4504 PN16Air Vent: Brass
RatingMax Working Pressure: 10 BarTest Pressure: 16 BarMax Working Temp: 110oC
Part No. DN O/Dia Dim Dim Dim Dim Weight Nominal“A” “B” “C” “D” “E” Flow Rate
@1.5m/s
mm mm mm mm mm kg m3/hr
FEJ.CVAD–40 40 168 350 340 550 120 11 7.6
FEJ.CVAD–50 50 168 350 340 550 120 12 12.2
FEJ.CVAD–65 65 168 350 340 550 120 13 20.4
FEJ.CVAD–80 80 219 460 490 700 195 21 28.2
FEJ.CVAD–100 100 219 460 490 700 195 24 47.6
FEJ.CVAD–125 125 273 630 720 930 310 41 72.3
FEJ.CVAD–150 150 324 630 720 930 310 50 103.3
FEJ.CVAD–200 200 406 780 800 1010 350 69 174.3
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
7 -2 FlexEJ copyright 2011- R3/11
Flanged Air & Dirt Separator
ApplicationCombines the removal of air and dirt in a single unit; helps to avoid problems such as pump failure, energyloss and corrosion. Dirt and sludge is drained off manually, whilst the automatic air vent is constantlyoperating.
PerformanceOptimum performance at or below the given nominal flow rate and between -10oC and 110oC; operatingat greater than the nominal flow rate will reduce the performance of the unit. Direction of flow is at user’s option.
InstallationIdeally should be installed at the hottest point of the system or on the return leg of chilling systems. Shouldbe installed upstream of rotating equipment, valves etc to offer best protection from dirt and entrained air.
Pressure DropCalculated pressure drop for the Air & Dirt Separator
100
1000
10000
0001001011
Flow M3/Hr
Pre
ssu
re D
rop
Pa
DN40 DN50 DN65 DN80 DN100 DN125 DN150 DN200
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 7-3
Dosing PotsSection
7
Dosing pots are required in order to feed liquidchemicals, such as corrosion inhibitors or antifreeze,into closed systems safely.
All FlexEJ Dosing Pots are supplied with:
• Drain Valve
• Return Flow Valve
• Flow Valve
• Non Return Valve
• Wall Brackets
• Filling Valve
• Carbon Steel Pipe Body
• Tundish
• Air Release Valve
It is important that the dosing pot is correctly attachedto the system to allow rapid chemical feed. Choose alocation near a main pipe run or system header.
For capacities and dimension see attached drawings
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
7 -4 FlexEJ copyright 2011- R3/11
Dosing Pots
FlexEJ
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 7-5
Dosing PotsSection
7
FlexEJ
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 7-7
Dosing Pot Installation ManualSection
7
2011
Introduction
Dosing pots are required in order to feed liquid chemicals, such as corrosion inhibitors or antifreeze, into closed systems safely.
All Dosing Pots are supplied with:
1. Drainage Valve 6. Return Flow Valve
2. Flow Valve 7. Non Return Valve
3. Wall Brackets 8. Filling Valve
4. Steel Pipe Body 9. Tundish
5. Air Release Valve
Installing & Maintaining Your Dosing Pot
It is important that the dosing pot is correctly attached to the system to allow rapid chemical feed. Choose a location near a main pipe run or system header. Fasten the chemical dosing pot securely in place using the brackets attached to the back of the steel body.
Pipe the drain valve away to a safe disposal point. It is best to connect to the system across the flow andreturn pipe work. The flow connection should be made to the appropriately named “Flow Valve” at thebottom of the pot and the return connection made to the appropriately named “Return Valve”.
For all working conditions please refer to the data sheet provided. The Dosing Pot should not be operatedoutside of these limits.
After long term use the valves may wear. They should be inspected periodically and if necessary replaced.The Dosing Pot itself should also be checked periodically for corrosion and other wear. A 1mm corrosionallowance has been incorporated into the design. If corrosion is found to be greater than 1mm the potshould be removed and replaced.
A non return valve is fitted below the filling valve to prevent blow back occurring. The Dosing Pot couldreach temperatures of up to 120oc.
PPE appropriate for the working temperature and chemicals being used must be worn.Hazard Warnings should be fitted at the installation location and be visible to the operator in order to prevent the operator from causing harm to themselves or others.
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
7 -8 FlexEJ copyright 2011- R3/11
Dosing Pot Installation Manual
Tundish
Filling Valve
Air Release Valve
Flow Valve
NonReturnValve
ReturnFlowValve
Mounting Brackets
Drain Valve
Dosing Pot Components
For Technical Assistance and Sales Contact: FlexEJ Ltd
Tel: +44 (0) 1384 881188 Email: [email protected]
Fax: +44 (0) 1384 896875 Web: www.flexej.co.uk
FlexEJ copyright 2011- R3/11 7-9
Dosing Pot Installation ManualSection
7
Step 1 - Isolate Pot• Close All Valves
Step 2 - Drain Pot • Ensure drain is piped away to safe disposal• Open Filling and Drain Valves
Step 3 - Fill Pot• Close Drain Valve• Pour Chemical into Tundish • Open Filling Valve
Step 4 - Release Air• Open Air Release Valve until liquid appears
ValvesClosed
ValvesClosed
Valves Closed
ValveClosed
ValveClosed
ValveOpen
ValveOpen
Open valve after fillingtundish
For Technical Assistance and Sales Contact: FlexEJ Ltd Tel: +44 (0) 1384 881188 Fax: +44 (0) 1384 896875 Email: [email protected] Web: www.flexej.co.uk
7 -10 FlexEJ copyright 2011- R3/11
Dosing Pot Installation Manual
Valves Closed
Valves Open
Step 5 – Inject Chemicals• Close Filling and Drain Valves• Open Flow and Return Valves