FLANGES MASTER CATALOG - Fluid-Tec · SAE J518 FLANGE JIS B2291 SQUARE FLANGE ANSI B16.5 FLANGE JIS B2220 FLANGE DIN FLANGE. CONTENT PAGE FLUID-TEC Fluid-Tec Engineering & Trading

Fluid-Tec Engineering & Trading Pte Ltd No. 5 Kian Teck Way Singapore 628733 Tel : +65 6264-3881 Fax : +65 6265-9707 Website: www.fluid-tec.net Email: [email protected]

FLUID-TEC FLANGE

FLANGES MASTER CATALOG SAE J518 FLANGE ● JIS B2291 SQUARE FLANGE ANSI B16.5 FLANGE ● JIS B2220 FLANGE ● DIN FLANGE

http://www.fluid-tec.net

mailto:[email protected]?subject=



CONTENT PAGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733

Tel : +65 6264-3881 ● Fax : +65 6265-9707 ● Website: www.fluid-tec.net ● Email: [email protected]

SAE J518 FLANGE SPLIT FLANGE 1

FLANGE CLAMP 2

BSPP THREADED FLANGE (O-RING FACE) 3

BSPP THREADED COUNTERFLANGE (FLAT FACE) 4

NPT THREADED FLANGE (O-RING FACE) 5

NPT THREADED COUNTERFLANGE (FLAT FACE) 6

SOCKET WELD FLANGE (O-RING FACE) 7

SOCKET WELD COUNTERFLANGE (FLAT FACE) 8

BUTT WELD FLANGE (O-RING FACE) 9

BUTT WELD COUNTERFLANGE (FLAT FACE) 10

BLIND FLANGE (O-RING FACE) 11

BLIND COUNTERFLANGE (FLAT FACE) 12

JIS B2291 SQUARE FLANGESSAB 210K SQUARE FLANGE 13

SHAB 210K SQUARE FLANGE 14

ANSI B16.5 STANDARD FLANGE#150 SOCKET WELD (SW) FLANGE 15

#150 WELDED NECK (WN) FLANGE 16

#150 SLIP ON (SO) FLANGE 17

#150 BLIND (BL) FLANGE 17

#150 THREADED (TR) FLANGE 18

#150 LAP JOINT (LJ) FLANGE 18

#300 SOCKET WELD (SW) FLANGE 19






#600 SOCKET WELD (SW) FLANGE 23










JIS B2220 STANDARD FLANGEJIS 5K SLIP-ON PLATE (SOP) FLANGE 27

JIS 5K SLIP-ON HUB (SOH) FLANGE 27

JIS 5K BLIND (BL) FLANGE 28

JIS 10K SLIP-ON PLATE (SOP) FLANGE 29



JIS 16K SLIP-ON PLATE (SOP) FLANGE 31



DIN STANDARD FLANGEPN10 SLIP-ON PLATE (SOP) FLANGE 33

PN10 BLIND PLATE (BLFF) FLANGE 33

PN10 WELDED-NECK (WNRF) FLAGE 34

PN16 SLIP-ON PLATE (SOP) FLANGE 35

PN16 BLIND PLATE (BLFF) FLANGE 35

PN16 WELDED-NECK (WNRF) FLAGE 36

CONTENT PAGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733






Code 61 Split Flange

Part No. Size A B d h M N BoltCS SS DN in mm mm mm mm mm mm size x lgth

FL-08 FL-08 SS 13 1/2” 54.0 45.6 9.0 6.2 38.1 17.5 M8 x 30FL-12 FL-12 SS 19 3/4” 65.0 51.8 11.0 6.2 47.6 22.2 M10 x 35FL-16 FL-16 SS 25 1” 70.0 58.4 11.0 7.5 52.4 26.2 M10 x 35FL-20 FL-20 SS 32 1.1/4” 79.0 72.6 11.0 7.5 58.7 30.2 M10 x 40

FL-24 FL-24 SS 38 1.1/2” 94.0 82.2 13.5 7.5 69.9 35.7 M12 x 45FL-32 FL-32 SS 51 2” 102.0 96.4 13.5 9.0 77.8 42.9 M12 x 45FL-40 FL-40 SS 64 2.1/2” 114.0 108.2 13.5 9.0 88.9 50.8 M12 x 45FL-48 FL-48 SS 76 3" 135.0 130.6 17.5 9.0 106.4 61.9 M16 x 50FL-56 FL-56 SS 89 3.1/2” 152.0 139.2 17.5 10.7 120.7 69.9 M16 x 50FL-64 FL-64 SS 102 4” 162.0 151.8 17.5 10.7 130.2 77.8 M16 x 50

Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733 Tel : +65 6264-3881 ● Fax : +65 6265-9707 ● Website: www.fluid-tec.net ● Email: [email protected]

SAE J518 SPLIT FLANGE

Standard/ApprovalSAE J518 ISO 6162Types

Code 61 : 3,000 PSI Code 62 : 6,000 PSI CAT Flange 9,000 PSIAvailable Material

CS 20#, Q235, Q345… AISI 304/316

SPECIFICATIONS & DIMENSIONS

Code 62 Split Flange


FS-08 FS-08 SS 13 1/2” 56.0 47.2 9.0 7.2 40.5 18.2 M8 x 30

FS-12 FS-12 SS 19 3/4” 71.0 60.0 11.0 8.2 50.8 23.8 M10 x 35FS-16 FS-16 SS 25 1” 81.0 69.6 13.5 9.0 57.2 27.8 M12 x 45FS-20 FS-20 SS 32 1.1/4” 95.0 77.2 13.5 9.8 66.6 31.8 M12 x 45FS-24 FS-24 SS 38 1.1/2” 113.0 95.0 17.5 12.0 79.3 36.3 M16 x 50FS-32 FS-32 SS 51 2” 133.0 113.8 22.0 12.0 96.8 44.5 M20 x 65FS-40 FS-40 SS 64 2.1/2” 175.0 150.0 25.0 20.5 123.8 58.7 M24 x 80

FS-48 FS-48 SS 76 3" 215.0 178.0 31.5 25.5 152.4 71.4 M30 x 90

CAT #9000 Split Flange

Part No. Size A B d h M N Bolt

CS SS DN in mm mm mm mm mm mm size x lgthPTX-12 - 19 3/4” 75.0 61.6 10.5 13.5 50.8 22.8 M10 x 35PTX-16 - 25 1” 81.1 68.0 12.0 13.5 57.2 25.8 M12 x 45PTX-20 - 32 1.1/4” 95.3 75.8 13.5 13.5 66.7 29.8 M14 x 45PTX-24 - 38 1.1/2” 112.8 68.0 16.5 13.5 79.4 34.6 M16 x 50

SAE J518 FLANGE FLUID-TEC 1





Code 61 Flange Clamp


FL-08 FL-08 SS 13 1/2” 54.0 45.6 9.0 6.2 38.1 17.5 M8 x 30FL-12 FL-12 SS 19 3/4” 65.0 51.8 11.0 6.2 47.6 22.2 M10 x 35FL-16 FL-16 SS 25 1” 70.0 58.4 11.0 7.5 52.4 26.2 M10 x 35FL-20 FL-20 SS 32 1.1/4” 79.0 72.6 11.0 7.5 58.7 30.2 M10 x 40

FL-24 FL-24 SS 38 1.1/2” 94.0 82.2 13.5 7.5 69.9 35.7 M12 x 45FL-32 FL-32 SS 51 2” 102.0 96.4 13.5 9.0 77.8 42.9 M12 x 45FL-40 FL-40 SS 64 2.1/2” 114.0 108.2 13.5 9.0 88.9 50.8 M12 x 45FL-48 FL-48 SS 76 3" 135.0 130.6 17.5 9.0 106.4 61.9 M16 x 50FL-56 FL-56 SS 89 3.1/2” 152.0 139.2 17.5 10.7 120.7 69.9 M16 x 50FL-64 FL-64 SS 102 4” 162.0 151.8 17.5 10.7 130.2 77.8 M16 x 50


SAE J518 FLANGE CLAMP


Code 61 : 3,000 PSI Code 62 : 6,000 PSI

Available MaterialCS 20#, Q235, Q345… AISI 304/316


Code 62 Flange Clamp


FS-08 FS-08 SS 13 1/2” 56.0 47.2 9.0 7.2 40.5 18.2 M8 x 30

FS-12 FS-12 SS 19 3/4” 71.0 60.0 11.0 8.2 50.8 23.8 M10 x 35FS-16 FS-16 SS 25 1” 81.0 69.6 13.5 9.0 57.2 27.8 M12 x 45FS-20 FS-20 SS 32 1.1/4” 95.0 77.2 13.5 9.8 66.6 31.8 M12 x 45FS-24 FS-24 SS 38 1.1/2” 113.0 95.0 17.5 12.0 79.3 36.3 M16 x 50FS-32 FS-32 SS 51 2” 133.0 113.8 22.0 12.0 96.8 44.5 M20 x 65FS-40 FS-40 SS 64 2.1/2” 175.0 150.0 25.0 20.5 123.8 58.7 M24 x 80

FS-48 FS-48 SS 76 3" 215.0 178.0 31.5 25.5 152.4 71.4 M30 x 90






BSPP Threaded O-Ring Face Code 61 Flange

Part No. Size D F G H I L M K BoltCS SS DN in mm mm mm mm mm mm mm mm size x lgth

AFS080G AFS080G SS 13 1/2” 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30AFS100G AFS100G SS 19 3/4” 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35AFS102G AFS102G SS 25 1” 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35AFS104G AFS104G SS 32 1.1/4” 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

AFS106G AFS106G SS 38 1.1/2” 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45AFS108G AFS108G SS 51 2” 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45AFS110G AFS110G SS 64 2.1/2” 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45AFS112G AFS112G SS 76 3" 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50AFS114G AFS114G SS 89 3.1/2” 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50AFS116G AFS116G SS 102 4” 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

AFS118G AFS118G SS 102 5” 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55


SAE J518 BSPP THREADED FLANGE

(O-RING FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



BSPP Threaded O-Ring Face Code 62 Flange


AFS401G AFS401G SS 13 1/2” 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30AFS402G AFS402G SS 19 3/4” 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

AFS403G AFS403G SS 25 1” 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45AFS404G AFS404G SS 32 1.1/4” 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45AFS405G AFS405G SS 38 1.1/2” 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50AFS406G AFS406G SS 51 2” 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65AFS407G AFS407G SS 64 2.1/2” 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80AFS408G AFS408G SS 76 3" 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90






BSPP Threaded Flat Face Code 61 Flange


GFS080G GFS080G SS 13 1/2” 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30GFS100G GFS100G SS 19 3/4” 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35GFS102G GFS102G SS 25 1” 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35GFS104G GFS104G SS 32 1.1/4” 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

GFS106G GFS106G SS 38 1.1/2” 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45GFS108G GFS108G SS 51 2” 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45GFS110G GFS110G SS 64 2.1/2” 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45GFS112G GFS112G SS 76 3" 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50GFS114G GFS114G SS 89 3.1/2” 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50GFS116G GFS116G SS 102 4” 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

GFS118G GFS118G SS 102 5” 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55


SAE J518 BSPP THREADED COUNTERFLANGE

(FLAT FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



BSPP Threaded Flat Face Code 62 Flange


GFS401G GFS401G SS 13 1/2” 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30GFS402G GFS402G SS 19 3/4” 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

GFS403G GFS403G SS 25 1” 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45GFS404G GFS404G SS 32 1.1/4” 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45GFS405G GFS405G SS 38 1.1/2” 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50GFS406G GFS406G SS 51 2” 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65GFS407G GFS407G SS 64 2.1/2” 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80GFS408G GFS408G SS 76 3" 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90






NPT Threaded O-Ring Face Code 61 Flange


AFS080N AFS080N SS 13 1/2” 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30AFS100N AFS100N SS 19 3/4” 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35AFS102N AFS102N SS 25 1” 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35AFS104N AFS104N SS 32 1.1/4” 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

AFS106N AFS106N SS 38 1.1/2” 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45AFS108N AFS108N SS 51 2” 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45AFS110N AFS110N SS 64 2.1/2” 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45AFS112N AFS112N SS 76 3" 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50AFS114N AFS114N SS 89 3.1/2” 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50AFS116N AFS116N SS 102 4” 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

AFS118N AFS118N SS 102 5” 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55



Code 61 : 3,000 PSI Code 62 : 6,000 PSI



NPT Threaded O-Ring Face Code 62 Flange


AFS401N AFS401N SS 13 1/2” 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30AFS402N AFS402N SS 19 3/4” 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

AFS403N AFS403N SS 25 1” 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45AFS404N AFS404N SS 32 1.1/4” 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45AFS405N AFS405N SS 38 1.1/2” 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50AFS406N AFS406N SS 51 2” 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65AFS407N AFS407N SS 64 2.1/2” 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80AFS408N AFS408N SS 76 3" 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90

SAE J518 NPT THREADED FLANGE

(O-RING FACE)






NPT Threaded Flat Face Code 61 Flange


GFS080N GFS080N SS 13 1/2” 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30GFS100N GFS100N SS 19 3/4” 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35GFS102N GFS102N SS 25 1” 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35GFS104N GFS104N SS 32 1.1/4” 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

GFS106N GFS106N SS 38 1.1/2” 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45GFS108N GFS108N SS 51 2” 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45GFS110N GFS110N SS 64 2.1/2” 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45GFS112N GFS112N SS 76 3" 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50GFS114N GFS114N SS 89 3.1/2” 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50GFS116N GFS116N SS 102 4” 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

GFS118N GFS118N SS 102 5” 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55


SAE J518 NPT THREADED COUNTERFLANGE

(FLAT FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



NPT Threaded Flat Face Code 62 Flange


GFS401N GFS401N SS 13 1/2” 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30GFS402N GFS402N SS 19 3/4” 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

GFS403N GFS403N SS 25 1” 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45GFS404N GFS404N SS 32 1.1/4” 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45GFS405N GFS405N SS 38 1.1/2” 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50GFS406N GFS406N SS 51 2” 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65GFS407N GFS407N SS 64 2.1/2” 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80GFS408N GFS408N SS 76 3" 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90







SAE J518 SOCKET WELD FLANGE

(O-RING FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Socket Weld O-Ring Face Code 61 Flange

Part No. Size B D F G H I L M K BoltCS SS DN in mm mm mm mm mm mm mm mm mm size x lgth

AFS080S AFS080S SS 13 1/2” 21.6 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30AFS100S AFS100S SS 19 3/4” 27.2 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35AFS102S AFS102S SS 25 1” 34.0 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35AFS104S AFS104S SS 32 1.1/4” 42.8 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

AFS106S AFS106S SS 38 1.1/2” 48.6 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45AFS108S AFS108S SS 51 2” 61.0 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45AFS110S AFS110S SS 64 2.1/2” 63.0 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45AFS112S AFS112S SS 76 3" 90.5 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50AFS114S AFS114S SS 89 3.1/2” 103.0 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50AFS116S AFS116S SS 102 4” 115.5 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

AFS118S AFS118S SS 102 5” 142.0 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55

Socket Weld O-Ring Face Code 62 Flange


AFS401S AFS401S SS 13 1/2” 21.6 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30AFS402S AFS402S SS 19 3/4” 27.2 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

AFS403S AFS403S SS 25 1” 34.0 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45AFS404S AFS404S SS 32 1.1/4” 42.8 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45AFS405S AFS405S SS 38 1.1/2” 48.6 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50AFS406S AFS406S SS 51 2” 61.0 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65AFS407S AFS407S SS 64 2.1/2” 63.0 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80AFS408S AFS408S SS 76 3" 90.5 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90






Socket Weld Flat Face Code 61 Flange


GFS080S GFS080S SS 13 1/2” 21.6 16.0 47 57 17.5 38.1 36 15 8.7 M8 x 30GFS100S GFS100S SS 19 3/4” 27.2 18.0 50 67 22.3 47.6 36 18 10.5 M10 x 35GFS102S GFS102S SS 25 1” 34.0 18.0 54 72 26.2 52.4 38 20 10.5 M10 x 35GFS104S GFS104S SS 32 1.1/4” 42.8 21.0 68 82 30.2 58.7 41 22 11.7 M10 x 40

GFS106S GFS106S SS 38 1.1/2” 48.6 25.0 79 96 35.7 69.9 44 24 13.5 M12 x 45GFS108S GFS108S SS 51 2” 61.0 25.5 102 102 42.9 77.8 45 26 13.5 M12 x 45GFS110S GFS110S SS 64 2.1/2” 63.0 26.0 115 115 50.8 88.9 50 30 13.5 M12 x 45GFS112S GFS112S SS 76 3" 90.5 27.5 137 137 61.9 106.4 50 30 17.5 M16 x 50GFS114S GFS114S SS 89 3.1/2” 103.0 27.5 155 155 69.9 120.7 50 30 17.5 M16 x 50GFS116S GFS116S SS 102 4” 115.5 27.5 163 163 77.8 130.2 50 30 17.5 M16 x 50

GFS118S GFS118S SS 102 5” 142.0 28.0 184 184 92.0 152.4 50 30 17.5 M16 x 55


SAE J518 SOCKET WELD COUNTERFLANGE

(FLAT FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Socket Weld Flat Face Code 62 Flange


GFS401S GFS401S SS 13 1/2” 21.6 16.5 46 54 18.2 40.5 36 19 8.7 M8 x 30GFS402S GFS402S SS 19 3/4” 27.2 19.5 55 71 23.8 50.8 36 22 10.5 M10 x 35

GFS403S GFS403S SS 25 1” 34.0 25.5 65 81 27.8 57.2 42 22 13.0 M12 x 45GFS404S GFS404S SS 32 1.1/4” 42.8 27.5 78 95 31.6 66.6 45 25 13.5 M12 x 45GFS405S GFS405S SS 38 1.1/2” 48.6 31.0 94 112 36.5 79.3 50 26 17.0 M16 x 50GFS406S GFS406S SS 51 2” 61.0 37.0 114 134 44.5 96.8 65 32 21.0 M20 x 65GFS407S GFS407S SS 64 2.1/2” 63.0 45.0 150 175 58.7 123.8 77 32 25.0 M24 x 80GFS408S GFS408S SS 76 3" 90.5 55.0 178 210 71.4 152.4 90 35 31.5 M30 x 90






Butt Weld O-Ring Face Code 61 Flange

Part No. Size B D F G H I L K BoltCS SS DN in mm mm mm mm mm mm mm mm size x lgth

AFS080ST AFS080ST SS 13 1/2” 21.3 x 3.7 16.0 47 57 17.5 38.1 36 8.7 M8 x 30AFS100ST AFS100ST SS 19 3/4” 26.7 x 3.9 18.0 50 67 22.3 47.6 36 10.5 M10 x 35AFS102ST AFS102ST SS 25 1” 33.4 x 4.5 18.0 54 72 26.2 52.4 38 10.5 M10 x 35AFS104ST AFS104ST SS 32 1.1/4” 42.2 x 4.9 21.0 68 82 30.2 58.7 41 11.7 M10 x 40

AFS106ST AFS106ST SS 38 1.1/2” 48.3 x 5.1 25.0 79 96 35.7 69.9 44 13.5 M12 x 45AFS108ST AFS108ST SS 51 2” 60.3 x 5.5 25.5 102 102 42.9 77.8 45 13.5 M12 x 45AFS110ST AFS110ST SS 64 2.1/2” 73.0 x 7.0 26.0 115 115 50.8 88.9 50 13.5 M12 x 45AFS112ST AFS112ST SS 76 3" 88.9 x 7.6 27.5 137 137 61.9 106.4 50 17.5 M16 x 50AFS114ST AFS114ST SS 89 3.1/2” 101.6 x 8.1 27.5 155 155 69.9 120.7 50 17.5 M16 x 50AFS116ST AFS116ST SS 102 4” 114.3 x 8.6 27.5 163 163 77.8 130.2 50 17.5 M16 x 50

AFS118ST AFS118ST SS 102 5” 141.3 x 9.5 28.0 184 184 92.0 152.4 50 17.5 M16 x 55


SAE J518 BUTT WELD FLANGE

(O-RING FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Butt Weld O-Ring Face Code 62 Flange


AFS401ST AFS401ST SS 13 1/2” 21.3 x 3.7 16.5 46 54 18.2 40.5 36 8.7 M8 x 30AFS402ST AFS402ST SS 19 3/4” 26.7 x 3.9 19.5 55 71 23.8 50.8 36 10.5 M10 x 35

AFS403ST AFS403ST SS 25 1” 33.4 x 4.5 25.5 65 81 27.8 57.2 42 13.0 M12 x 45AFS404ST AFS404ST SS 32 1.1/4” 42.2 x 4.9 27.5 78 95 31.6 66.6 45 13.5 M12 x 45AFS405ST AFS405ST SS 38 1.1/2” 48.3 x 5.1 31.0 94 112 36.5 79.3 50 17.0 M16 x 50AFS406ST AFS406ST SS 51 2” 60.3 x 5.5 37.0 114 134 44.5 96.8 65 21.0 M20 x 65AFS407ST AFS407ST SS 64 2.1/2” 73.0 x 7.0 45.0 150 175 58.7 123.8 75 25.0 M24 x 80AFS408ST AFS408ST SS 76 3" 88.9 x 7.6 55.0 178 210 71.4 152.4 88 31.5 M30 x 90







SAE J518 BUTT WELD COUNTERFLANGE

(FLAT FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Butt Weld Flat Face Code 61 Flange


AFS080ST AFS080ST SS 13 1/2” 21.3 x 3.7 16.0 47 57 17.5 38.1 36 8.7 M8 x 30AFS100ST AFS100ST SS 19 3/4” 26.7 x 3.9 18.0 50 67 22.3 47.6 36 10.5 M10 x 35AFS102ST AFS102ST SS 25 1” 33.4 x 4.5 18.0 54 72 26.2 52.4 38 10.5 M10 x 35AFS104ST AFS104ST SS 32 1.1/4” 42.2 x 4.9 21.0 68 82 30.2 58.7 41 11.7 M10 x 40

AFS106ST AFS106ST SS 38 1.1/2” 48.3 x 5.1 25.0 79 96 35.7 69.9 44 13.5 M12 x 45AFS108ST AFS108ST SS 51 2” 60.3 x 5.5 25.5 102 102 42.9 77.8 45 13.5 M12 x 45AFS110ST AFS110ST SS 64 2.1/2” 73.0 x 7.0 26.0 115 115 50.8 88.9 50 13.5 M12 x 45AFS112ST AFS112ST SS 76 3" 88.9 x 7.6 27.5 137 137 61.9 106.4 50 17.5 M16 x 50AFS114ST AFS114ST SS 89 3.1/2” 101.6 x 8.1 27.5 155 155 69.9 120.7 50 17.5 M16 x 50AFS116ST AFS116ST SS 102 4” 114.3 x 8.6 27.5 163 163 77.8 130.2 50 17.5 M16 x 50

AFS118ST AFS118ST SS 102 5” 141.3 x 9.5 28.0 184 184 92.0 152.4 50 17.5 M16 x 55

Butt Weld Flat Face Code 62 Flange


AFS401ST AFS401ST SS 13 1/2” 21.3 x 3.7 16.5 46 54 18.2 40.5 36 8.7 M8 x 30AFS402ST AFS402ST SS 19 3/4” 26.7 x 3.9 19.5 55 71 23.8 50.8 36 10.5 M10 x 35

AFS403ST AFS403ST SS 25 1” 33.4 x 4.5 25.5 65 81 27.8 57.2 42 13.0 M12 x 45AFS404ST AFS404ST SS 32 1.1/4” 42.2 x 4.9 27.5 78 95 31.6 66.6 45 13.5 M12 x 45AFS405ST AFS405ST SS 38 1.1/2” 48.3 x 5.1 31.0 94 112 36.5 79.3 50 17.0 M16 x 50AFS406ST AFS406ST SS 51 2” 60.3 x 5.5 37.0 114 134 44.5 96.8 65 21.0 M20 x 65AFS407ST AFS407ST SS 64 2.1/2” 73.0 x 7.0 45.0 150 175 58.7 123.8 75 25.0 M24 x 80AFS408ST AFS408ST SS 76 3" 88.9 x 7.6 55.0 178 210 71.4 152.4 88 31.5 M30 x 90







Blind O-Ring Face Code 61 Flange

Part No. Size D F G H I K BoltCS SS DN in mm mm mm mm mm mm size x lgth

AFS080 AFS080 SS 13 1/2” 16.0 47 57 17.5 38.1 8.7 M8 x 30AFS100 AFS100 SS 19 3/4” 18.0 50 67 22.3 47.6 10.5 M10 x 35AFS102 AFS102 SS 25 1” 18.0 54 72 26.2 52.4 10.5 M10 x 35AFS104 AFS104 SS 32 1.1/4” 21.0 68 82 30.2 58.7 11.7 M10 x 40

AFS106 AFS106 SS 38 1.1/2” 25.0 79 96 35.7 69.9 13.5 M12 x 45AFS108 AFS108 SS 51 2” 25.5 102 102 42.9 77.8 13.5 M12 x 45AFS110 AFS110 SS 64 2.1/2” 26.0 115 115 50.8 88.9 13.5 M12 x 45AFS112 AFS112 SS 76 3" 27.5 137 137 61.9 106.4 17.5 M16 x 50AFS114 AFS114 SS 89 3.1/2” 27.5 155 155 69.9 120.7 17.5 M16 x 50AFS116 AFS116 SS 102 4” 27.5 163 163 77.8 130.2 17.5 M16 x 50

AFS118 AFS118 SS 102 5” 28.0 184 184 92.0 152.4 17.5 M16 x 55


SAE J518 BLIND FLANGE (O-RING FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Blind O-Ring Face Code 62 Flange


AFS401 AFS401 SS 13 1/2” 16.5 46 54 18.2 40.5 8.7 M8 x 30AFS402 AFS402 SS 19 3/4” 19.5 55 71 23.8 50.8 10.5 M10 x 35

AFS403 AFS403 SS 25 1” 25.5 65 81 27.8 57.2 13.0 M12 x 45AFS404 AFS404 SS 32 1.1/4” 27.5 78 95 31.6 66.6 13.5 M12 x 45AFS405 AFS405 SS 38 1.1/2” 31.0 94 112 36.5 79.3 17.0 M16 x 50AFS406 AFS406 SS 51 2” 37.0 114 134 44.5 96.8 21.0 M20 x 65AFS407 AFS407 SS 64 2.1/2” 45.0 150 175 58.7 123.8 25.0 M24 x 80AFS408 AFS408 SS 76 3" 55.0 178 210 71.4 152.4 31.5 M30 x 90










Blind Flat Face Code 61 Flange


GFS080 GFS080 SS 13 1/2” 16.0 47 57 17.5 38.1 8.7 M8 x 30GFS100 GFS100 SS 19 3/4” 18.0 50 67 22.3 47.6 10.5 M10 x 35GFS102 GFS102 SS 25 1” 18.0 54 72 26.2 52.4 10.5 M10 x 35GFS104 GFS104 SS 32 1.1/4” 21.0 68 82 30.2 58.7 11.7 M10 x 40

GFS106 GFS106 SS 38 1.1/2” 25.0 79 96 35.7 69.9 13.5 M12 x 45GFS108 GFS108 SS 51 2” 25.5 102 102 42.9 77.8 13.5 M12 x 45GFS110 GFS110 SS 64 2.1/2” 26.0 115 115 50.8 88.9 13.5 M12 x 45GFS112 GFS112 SS 76 3" 27.5 137 137 61.9 106.4 17.5 M16 x 50GFS114 GFS114 SS 89 3.1/2” 27.5 155 155 69.9 120.7 17.5 M16 x 50GFS116 GFS116 SS 102 4” 27.5 163 163 77.8 130.2 17.5 M16 x 50

GFS118 GFS118 SS 102 5” 28.0 184 184 92.0 152.4 17.5 M16 x 55

SAE J518 FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


SAE J518 BLIND COUNTERFLANGE

(FLAT FACE)


Code 61 : 3,000 PSI Code 62 : 6,000 PSI



Blind Flat Face Code 62 Flange


GFS401 GFS401 SS 13 1/2” 16.5 46 54 18.2 40.5 8.7 M8 x 30GFS402 GFS402 SS 19 3/4” 19.5 55 71 23.8 50.8 10.5 M10 x 35

GFS403 GFS403 SS 25 1” 25.5 65 81 27.8 57.2 13.0 M12 x 45GFS404 GFS404 SS 32 1.1/4” 27.5 78 95 31.6 66.6 13.5 M12 x 45GFS405 GFS405 SS 38 1.1/2” 31.0 94 112 36.5 79.3 17.0 M16 x 50GFS406 GFS406 SS 51 2” 37.0 114 134 44.5 96.8 21.0 M20 x 65GFS407 GFS407 SS 64 2.1/2” 45.0 150 175 58.7 123.8 25.0 M24 x 80GFS408 GFS408 SS 76 3" 55.0 178 210 71.4 152.4 31.5 M30 x 90

12





JIS 210K O-RING FLANGE (SSA)

Part No. Size A A1 (max) B C D D1 D2 E D3 D4 F R

CS NB in mm mm mm mm mm mm mm mm mm mm mm mmW-210K-SHA-15A 15 1/2” 54 36 22 16.0 30 22.2 11 11 32 11 3.5 5.0W-210K-SHA-20A 20 3/4” 58 40 22 20.0 35 27.7 12 12 38 11 7.0 5.0W-210K-SHA-25A 25 1” 68 48 28 25.0 40 34.5 14 14 45 13 4.0 5.0

W-210K-SHA-32A 32 1.1/4” 76 56 28 31.5 45 43.2 16 16 56 13 6.0 5.0W-210K-SHA-40A 40 1.1/2” 92 65 36 37.5 55 49.1 18 18 63 18 7.0 5.0W-210K-SHA-50A 50 2” 100 73 36 47.5 65 61.1 20 20 75 18 7.0 5.0W-210K-SHA-65A 65 2.1/2” 128 92 45 60.0 80 77.1 22 22 95 22 9.5 6.0W-210K-SHA-80A 80 3" 140 103 45 71.0 90 90.0 25 25 108 24 11.0 6.0

JIS B2991 SQUARE FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


SSAB JIS 210K SQUARE FLANGE

Standard/ApprovalJIS B2991

Pressure Rating

210kgf/cm² 210 bar

Available MaterialSF440A SS316

Bolt TypeSocket Cap Screw


SSA SSB

JIS 210K FLAT FACE FLANGE (SSB)

Part No. Size A A1 (max)

B C D D1 D2 E D3 D4 F R

CS NB in mm mm mm mm mm mm mm mm mm mm mm mmW-210K-SHB-15A 15 1/2” 54 36 22 16.0 30 22.2 11 11 32 11 3.5 5.0

W-210K-SHB-20A 20 3/4” 58 40 22 20.0 35 27.7 12 12 38 11 7.0 5.0W-210K-SHB-25A 25 1” 68 48 28 25.0 40 34.5 14 14 45 13 4.0 5.0W-210K-SHB-32A 32 1.1/4” 76 56 28 31.5 45 43.2 16 16 56 13 6.0 5.0W-210K-SHB-40A 40 1.1/2” 92 65 36 37.5 55 49.1 18 18 63 18 7.0 5.0W-210K-SHB-50A 50 2” 100 73 36 47.5 65 61.1 20 20 75 18 7.0 5.0W-210K-SHB-65A 65 2.1/2” 128 92 45 60.0 80 77.1 22 22 95 22 9.5 6.0

W-210K-SHB-80A 80 3" 140 103 45 71.0 90 90.0 25 25 108 24 11.0 6.0

SSA (O-Ring)

SSB (Flat Face)

SSAB (Socket Cap Screw)

13





JIS 210K O-RING FLANGE (SHA)

Part No. Size A A1 (max) B C D D1 D2 E D3 D4 F R

CS NB in mm mm mm mm mm mm mm mm mm mm mm mmW-210K-SHA-15A 15 1/2” 63 67 22 16.0 30 22.2 11 11 32 11 3.5 5.0W-210K-SHA-20A 20 3/4” 68 72 22 20.0 35 27.7 12 12 38 11 7.0 5.0W-210K-SHA-25A 25 1” 80 85 28 25.0 40 34.5 14 14 45 13 4.0 5.0

W-210K-SHA-32A 32 1.1/4” 90 95 28 31.5 45 43.2 16 16 56 13 6.0 5.0W-210K-SHA-40A 40 1.1/2” 100 106 36 37.5 55 49.1 18 18 63 18 7.0 5.0W-210K-SHA-50A 50 2” 112 118 36 47.5 65 61.1 20 20 75 18 7.0 5.0W-210K-SHA-65A 65 2.1/2” 140 148 45 60.0 80 77.1 22 22 95 22 9.5 6.0W-210K-SHA-80A 80 3" 155 163 45 71.0 90 90.0 25 25 108 24 11.0 6.0

JIS B2991 SQUARE FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


SHAB JIS 210K SQUARE FLANGE

Standard/ApprovalJIS B2991

Pressure Rating

210kgf/cm² 210 bar

Available MaterialSF440A SS316

Bolt TypeHexagon Bolt


SHA SHB

JIS 210K FLAT FACE FLANGE (SHB)

Part No. Size A A1 (max)

B C D D1 D2 E D3 D4 F R

CS NB in mm mm mm mm mm mm mm mm mm mm mm mmW-210K-SHB-15A 15 1/2” 63 67 22 16.0 30 22.2 11 11 32 11 3.5 5.0

W-210K-SHB-20A 20 3/4” 68 72 22 20.0 35 27.7 12 12 38 11 7.0 5.0W-210K-SHB-25A 25 1” 80 85 28 25.0 40 34.5 14 14 45 13 4.0 5.0W-210K-SHB-32A 32 1.1/4” 90 95 28 31.5 45 43.2 16 16 56 13 6.0 5.0W-210K-SHB-40A 40 1.1/2” 100 106 36 37.5 55 49.1 18 18 63 18 7.0 5.0W-210K-SHB-50A 50 2” 112 118 36 47.5 65 61.1 20 20 75 18 7.0 5.0W-210K-SHB-65A 65 2.1/2” 140 148 45 60.0 80 77.1 22 22 95 22 9.5 6.0

W-210K-SHB-80A 80 3" 155 163 45 71.0 90 90.0 25 25 108 24 11.0 6.0

SHA (O-Ring)

SHB (Flat Face)

SHAB (Hexagon Bolt)

14





ANSI #150 FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


Standard/ApprovalASME/ANSI B16.5Available MaterialA105N SS304/316


Flange TypesSocket Weld (SW) Welded Neck (WN) Slip-on (SO) Blind (BL) Threaded (TR) Lap Joint (LJ)#150 SOCKET-WELD (SW) FLANGE

Nominal Pipe Size

Outside Dia.

Bore Dia.

Depth Thickness Raised Face Dia.

Lgth Thru Hub

Hub Dia.

Bolt Circle

No. of holes

Hole Dia.

mm in O B2 D T R Y X C mm mm15 1/2" 89 22.4 9.7 11.2 35.1 47.8 30.2 60.5 4 1620 3/4" 99 27.7 11.2 12.7 42.9 52.3 38.1 69.9 4 1625 1" 108 34.5 12.7 14.2 50.8 55.6 49.3 79.5 4 1632 1.1/4" 118 43.2 14.2 16.0 63.5 57.2 58.7 88.9 4 1640 1.1/2" 127 49.5 16.0 17.5 73.2 62.0 65.0 98.6 4 1650 2" 152 62.0 17.5 19.1 92.2 63.5 77.7 120.7 4 1965 2.1/2" 178 74.7 19.1 22.4 104.9 69.9 90.4 139.7 4 1980 3" 191 90.7 20.6 23.9 127.0 69.9 108.0 152.4 4 1990 3.1/2" 216 103.4 22.4 23.9 139.7 71.4 122.2 177.8 8 19

100 4" 229 116.1 23.9 23.9 157.2 76.2 134.9 190.5 8 19

Nominal Pipe Size

Bore Dia. (B1)

mm in SCH 10s SCH 40S / STD SCH 80s / XS SCH 16015 1/2" 17.1 15.8 13.9 11.820 3/4" 22.5 20.9 18.8 15.625 1" 27.9 26.6 24.3 20.732 1.1/4" 36.6 35.1 32.5 29.540 1.1/2" 42.7 40.9 38.1 34.050 2" 54.9 52.5 49.2 42.865 2.1/2" 67.2 62.7 59.2 53.980 3" 82.9 77.9 73.7 66.790 3.1/2" 95.6 90.1 85.5 -

100 4" 108.3 102.3 97.2 87.3

15









Flange TypesSocket Weld (SW) Welded Neck (WN) Slip-on (SO) Blind (BL) Threaded (TR) Lap Joint (LJ)#150 WELDED-NECK (WN) FLANGE

Nominal Pipe Size

Outside Dia.

Thickness Raised Face Dia.

Lgth Thru Hub

Weld Point

Hub Dia. Bolt Circle

No. of holes

Hole Dia.

mm in O T R Y A X C mm mm15 1/2" 89 11.2 35.1 47.8 21.3 30.2 60.5 4 1620 3/4" 99 12.7 42.9 52.3 26.7 38.1 69.9 4 1625 1" 108 14.2 50.8 55.6 33.5 49.3 79.5 4 1632 1.1/4" 118 16.0 63.5 57.2 42.2 58.7 88.9 4 1640 1.1/2" 127 17.5 73.2 62.0 48.3 65.0 98.6 4 1650 2" 152 19.1 92.2 63.5 60.5 77.7 120.7 4 1965 2.1/2" 178 22.4 104.9 69.9 73.2 90.4 139.7 4 1980 3" 191 23.9 127.0 69.9 88.9 108.0 152.4 4 1990 3.1/2" 216 23.9 139.7 71.4 101.6 122.2 177.8 8 19

100 4" 229 23.9 157.2 76.2 114.3 134.9 190.5 8 19125 5" 254 23.9 185.7 88.9 141.2 163.6 215.9 8 22150 6" 279 25.4 215.9 88.9 168.4 192.0 241.3 8 22200 8" 343 28.7 270.0 101.6 219.2 246.1 298.5 8 22250 10" 406 30.2 323.9 101.6 273.1 304.8 362.0 12 25300 12" 483 31.8 381.0 114.3 323.9 365.3 431.8 12 26

Nominal Pipe Size

Bore Dia. (B)


100 4" 108.3 102.3 97.2 87.3125 5" 134.4 128.2 122.3 109.5150 6" 161.6 154.1 146.3 131.8200 8" 211.6 202.7 193.7 173.1250 10" 264.6 254.4 247.7 215.9300 12" 314.6 304.8 298.5 257.2

16









Flange TypesSocket Weld (SW) Welded Neck (WN) Slip-on (SO) Blind (BL) Threaded (TR) Lap Joint (LJ)#150 SLIP-ON (SO) FLANGE

Nominal Pipe Size

Outside Dia.

Bore Dia. Thickness Raised Face Dia.

Length Thru Hub


No. of holes

Hole Dia.

mm in O B T R Y X C mm mm15 1/2" 89 22.4 11.2 35.1 15.9 30.2 60.5 4 1620 3/4" 99 27.7 12.7 42.9 15.9 38.1 69.9 4 1625 1" 108 34.5 14.2 50.8 17.5 49.3 79.5 4 1632 1.1/4" 118 43.2 16.0 63.5 20.6 58.7 88.9 4 1640 1.1/2" 127 49.5 17.5 73.2 22.2 65.0 98.6 4 1650 2" 152 62.0 19.1 92.2 25.4 77.7 120.7 4 1965 2.1/2" 178 74.4 22.4 104.9 28.4 90.4 139.7 4 1980 3" 191 90.7 23.9 127.0 30.2 108.0 152.4 4 1990 3.1/2" 216 103.4 23.9 139.7 31.8 122.2 177.8 8 19

100 4" 229 116.1 23.9 157.2 33.3 134.9 190.5 8 19125 5" 254 143.8 23.9 185.7 36.6 163.6 215.9 8 22150 6" 279 170.7 25.4 215.9 39.7 192.0 241.3 8 22200 8" 343 221.5 28.7 270.0 44.5 246.1 298.5 8 22250 10" 406 276.4 30.2 323.9 49.2 304.8 362.0 12 25300 12" 483 327.2 31.8 381.0 55.6 365.3 431.8 12 26



Flange TypesSocket Weld (SW) Welded Neck (WN) Slip-on (SO) Blind (BL) Threaded (TR) Lap Joint (LJ)

#150 BLIND (BL) FLANGE

Nominal Pipe Size Outside Dia. Thickness Raised Face Dia. Bolt Circle No. of holes

Hole Dia.

mm in O T R C mm mm15 1/2" 89 11.2 35.1 60.5 4 1620 3/4" 99 12.7 42.9 69.9 4 1625 1" 108 14.2 50.8 79.5 4 1632 1.1/4" 118 16.0 63.5 88.9 4 1640 1.1/2" 127 17.5 73.2 98.6 4 1650 2" 152 19.1 92.2 120.7 4 1965 2.1/2" 178 22.4 104.9 139.7 4 1980 3" 191 23.9 127.0 152.4 4 1990 3.1/2" 216 23.9 139.7 177.8 8 19

100 4" 229 23.9 157.2 190.5 8 19125 5" 254 23.9 185.7 215.9 8 22150 6" 279 25.4 215.9 241.3 8 22200 8" 343 28.7 270.0 298.5 8 22250 10" 406 30.2 323.9 362.0 12 25300 12" 483 31.8 381.0 431.8 12 26

17





Nominal Pipe Size

Outside Dia.

Bore Dia. Thickness Radius Length Thru Hub


No. of holes

Hole Dia.

mm in O B T r Y X C mm mm15 1/2" 89 17.1 11.2 3.0 15.9 30.2 60.5 4 1620 3/4" 99 22.5 12.7 3.0 15.9 38.1 69.9 4 1625 1" 108 27.9 14.2 3.0 17.5 49.3 79.5 4 1632 1.1/4" 118 36.3 16.0 5.0 20.6 58.7 88.9 4 1640 1.1/2" 127 42.7 17.5 6.0 22.2 65.0 98.6 4 1650 2" 152 54.9 19.1 8.0 25.4 77.7 120.7 4 1965 2.1/2" 178 67.2 22.4 8.0 28.4 90.4 139.7 4 1980 3" 191 82.9 23.9 10.0 30.2 108.0 152.4 4 1990 3.1/2" 216 95.6 23.9 10.0 31.8 122.2 177.8 8 19

100 4" 229 108.3 23.9 11.0 33.3 134.9 190.5 8 19125 5" 254 134.4 23.9 11.0 36.6 163.6 215.9 8 22150 6" 279 161.6 25.4 13.0 39.7 192.0 241.3 8 22200 8" 343 211.6 28.7 13.0 44.5 246.1 298.5 8 22250 10" 406 264.6 30.2 13.0 49.2 304.8 362.0 12 25300 12" 483 314.6 31.8 13.0 55.6 365.3 431.8 12 26





Flange TypesSocket Weld (SW) Welded Neck (WN) Slip-on (SO) Blind (BL) Threaded (TR) Lap Joint (LJ)#150 THREADED (TR) FLANGE

Nominal Pipe Size

Outside Dia.

Thread Type


Length Thru Hub


No. of holes

Hole Dia.

mm in O T R Y X C mm mm15 1/2" 89

To be specified by user

11.2 35.1 15.9 30.2 60.5 4 1620 3/4" 99 12.7 42.9 15.9 38.1 69.9 4 1625 1" 108 14.2 50.8 17.5 49.3 79.5 4 1632 1.1/4" 118 16.0 63.5 20.6 58.7 88.9 4 1640 1.1/2" 127 17.5 73.2 22.2 65.0 98.6 4 1650 2" 152 19.1 92.2 25.4 77.7 120.7 4 1965 2.1/2" 178 22.4 104.9 28.4 90.4 139.7 4 1980 3" 191 23.9 127.0 30.2 108.0 152.4 4 1990 3.1/2" 216 23.9 139.7 31.8 122.2 177.8 8 19

100 4" 229 23.9 157.2 33.3 134.9 190.5 8 19125 5" 254 23.9 185.7 36.6 163.6 215.9 8 22150 6" 279 25.4 215.9 39.7 192.0 241.3 8 22200 8" 343 28.7 270.0 44.5 246.1 298.5 8 22250 10" 406 30.2 323.9 49.2 304.8 362.0 12 25300 12" 483 31.8 381.0 55.6 365.3 431.8 12 26




#150 LAP JOINT (LJ) FLANGE

18







Nominal Pipe Size

Outside Dia.

Bore Dia.


Lgth Thru Hub

Hub Dia.

Bolt Circle

No. of holes

Hole Dia.

mm in O B2 D T R Y X C mm mm15 1/2" 95 22.4 9.7 14.3 35.1 22.2 38.1 66.5 4 1620 3/4" 117 27.7 11.2 15.9 42.9 25.4 47.8 82.6 4 1925 1" 124 34.5 12.7 17.5 50.8 27.0 54.0 88.9 4 1932 1.1/4" 133 43.2 14.2 19.1 63.5 27.0 63.5 98.6 4 1940 1.1/2" 155 49.5 15.8 20.6 73.2 30.2 69.9 114.3 4 2250 2" 165 62.0 17.5 22.4 91.9 33.3 84.1 127.0 8 2265 2.1/2" 190 74.7 19.1 25.4 104.6 38.1 100.0 149.4 8 2280 3" 210 90.7 20.6 28.6 127.0 42.9 117.3 168.1 8 2290 3.1/2" 229 103.4 22.3 30.2 139.7 44.4 133.4 184.2 8 22

100 4" 254 116.1 23.9 31.8 157.2 47.7 146.0 200.2 8 22

Nominal Pipe Size

Bore Dia. (B1)


100 4" 108.3 102.3 97.2 87.3




19










Nominal Pipe Size

Outside Dia.


Lgth Thru Hub

Weld Point


No. of holes

Hole Dia.

mm in O T R Y A X C mm mm15 1/2" 95 14.3 35.1 22.2 21.3 38.1 66.5 4 16.020 3/4" 117 15.9 42.9 25.4 26.7 47.8 82.6 4 19.025 1" 124 17.5 50.8 27.0 33.5 54.0 88.9 4 19.032 1.1/4" 133 19.1 63.5 27.0 42.2 63.5 98.6 4 19.040 1.1/2" 155 20.6 73.2 30.2 48.3 69.9 114.3 4 22.050 2" 165 22.4 91.9 33.3 60.5 84.1 127.0 8 22.065 2.1/2" 190 25.4 104.6 38.1 73.2 100.0 149.4 8 22.080 3" 210 28.6 127.0 42.9 88.9 117.3 168.1 8 22.090 3.1/2" 229 30.2 139.7 44.4 101.6 133.4 184.2 8 22.0

100 4" 254 31.8 157.2 47.7 114.3 146.0 200.2 8 22.0125 5" 279 35.1 185.7 50.8 141.2 177.8 235.0 8 22.0150 6" 318 36.6 215.9 52.3 168.4 206.2 269.7 12 22.0200 8" 381 41.3 269.7 61.9 219.2 260.3 330.2 12 26.0250 10" 444 47.8 323.9 66.7 273.1 320.7 387.3 12 29.0300 12" 520 50.8 381.0 73.0 323.9 374.7 450.9 12 32.0

Nominal Pipe Size

Bore Dia. (B)


100 4" 108.3 102.3 97.2 87.3125 5" 134.4 128.2 122.3 109.5150 6" 161.6 154.1 146.3 131.8200 8" 211.6 202.7 193.7 173.1250 10" 264.6 254.4 247.7 215.9300 12" 314.6 304.8 298.5 257.2

20










Nominal Pipe Size

Outside Dia.


Length Thru Hub


No. of holes

Hole Dia.

mm in O B T R Y X C mm mm15 1/2" 95 22.4 14.3 35.1 22.2 38.1 66.5 4 16.020 3/4" 117 27.7 15.9 42.9 25.4 47.8 82.6 4 19.025 1" 124 34.5 17.5 50.8 27.0 54.0 88.9 4 19.032 1.1/4" 133 43.2 19.1 63.5 27.0 63.5 98.6 4 19.040 1.1/2" 155 49.5 20.6 73.2 30.2 69.9 114.3 4 22.050 2" 165 62.0 22.4 91.9 33.3 84.1 127.0 8 22.065 2.1/2" 190 74.7 25.4 104.6 38.1 100.0 149.4 8 22.080 3" 210 90.7 28.6 127.0 42.9 117.3 168.1 8 22.090 3.1/2" 229 103.4 30.2 139.7 44.4 133.4 184.2 8 22.0

100 4" 254 116.1 31.8 157.2 47.7 146.0 200.2 8 22.0125 5" 279 143.8 35.1 185.7 50.8 177.8 235.0 8 22.0150 6" 318 170.7 36.6 215.9 52.3 206.2 269.7 12 22.0200 8" 381 221.5 41.3 269.7 61.9 260.3 330.2 12 26.0250 10" 444 276.4 47.8 323.9 66.7 320.7 387.3 12 29.0300 12" 520 327.2 50.8 381.0 73.0 374.7 450.9 12 32.0






Hole Dia.

mm in O T R C mm mm15 1/2" 95 14.3 35.1 66.5 4 16.020 3/4" 117 15.9 42.9 82.6 4 19.025 1" 124 17.5 50.8 88.9 4 19.032 1.1/4" 133 19.1 63.5 98.6 4 19.040 1.1/2" 155 20.6 73.2 114.3 4 22.050 2" 165 22.4 91.9 127.0 8 22.065 2.1/2" 190 25.4 104.6 149.4 8 22.080 3" 210 28.6 127.0 168.1 8 22.090 3.1/2" 229 30.2 139.7 184.2 8 22.0

100 4" 254 31.8 157.2 200.2 8 22.0125 5" 279 35.1 185.7 235.0 8 22.0150 6" 318 36.6 215.9 269.7 12 22.0200 8" 381 41.3 269.7 330.2 12 26.0250 10" 444 47.8 323.9 387.3 12 29.0300 12" 520 50.8 381.0 450.9 12 32.0

21





Nominal Pipe Size

Outside Dia.



No. of holes

Hole Dia.

mm in O B T r Y X C mm mm15 1/2" 95 22.9 14.3 3.0 22.2 38.1 66.5 4 16.020 3/4" 117 28.2 15.9 3.0 25.4 47.8 82.6 4 19.025 1" 124 35.1 17.5 3.0 27.0 54.0 88.9 4 19.032 1.1/4" 133 43.7 19.1 5.0 27.0 63.5 98.6 4 19.040 1.1/2" 155 50.0 20.6 6.0 30.2 69.9 114.3 4 22.050 2" 165 62.5 22.4 8.0 33.3 84.1 127.0 8 22.065 2.1/2" 190 75.4 25.4 8.0 38.1 100.0 149.4 8 22.080 3" 210 91.4 28.6 10.0 42.9 117.3 168.1 8 22.090 3.1/2" 229 104.1 30.2 10.0 44.4 133.4 184.2 8 22.0

100 4" 254 116.9 31.8 11.0 47.7 146.0 200.2 8 22.0125 5" 279 144.5 35.1 11.0 50.8 177.8 235.0 8 22.0150 6" 318 171.4 36.6 13.0 52.3 206.2 269.7 12 22.0200 8" 381 222.2 41.3 13.0 61.9 260.3 330.2 12 26.0250 10" 444 277.4 47.8 13.0 66.7 320.7 387.3 12 29.0300 12" 520 328.2 50.8 13.0 73.0 374.7 450.9 12 32.0






Nominal Pipe Size

Outside Dia.

Thread Type


Length Thru Hub


No. of holes

Hole Dia.



14.3 35.1 22.2 38.1 66.5 4 16.020 3/4" 117 15.9 42.9 25.4 47.8 82.6 4 19.025 1" 124 17.5 50.8 27.0 54.0 88.9 4 19.032 1.1/4" 133 19.1 63.5 27.0 63.5 98.6 4 19.040 1.1/2" 155 20.6 73.2 30.2 69.9 114.3 4 22.050 2" 165 22.4 91.9 33.3 84.1 127.0 8 22.065 2.1/2" 190 25.4 104.6 38.1 100.0 149.4 8 22.080 3" 210 28.6 127.0 42.9 117.3 168.1 8 22.090 3.1/2" 229 30.2 139.7 44.4 133.4 184.2 8 22.0

100 4" 254 31.8 157.2 47.7 146.0 200.2 8 22.0125 5" 279 35.1 185.7 50.8 177.8 235.0 8 22.0150 6" 318 36.6 215.9 52.3 206.2 269.7 12 22.0200 8" 381 41.3 269.7 61.9 260.3 330.2 12 26.0250 10" 444 47.8 323.9 66.7 320.7 387.3 12 29.0300 12" 520 50.8 381.0 73.0 374.7 450.9 12 32.0





22







Nominal Pipe Size

Outside Dia.

Bore Dia.


Lgth Thru Hub

Hub Dia.

Bolt Circle

No. of holes

Hole Dia.

mm in O B2 D T R Y X C mm mm15 1/2" 95 22.4 9.7 14.3 35.1 22.4 38.1 66.5 4 16.020 3/4" 117 27.7 11.2 15.9 42.9 25.4 47.8 82.5 4 19.025 1" 124 34.5 12.7 17.5 50.8 27.0 54.0 88.9 4 19.032 1.1/4" 133 43.2 14.2 20.6 63.5 28.4 63.5 98.6 4 19.040 1.1/2" 155 49.5 15.8 22.2 73.2 31.7 69.9 114.3 4 22.050 2" 165 62.0 17.5 25.4 91.9 36.5 84.1 127.0 8 19.065 2.1/2" 190 74.7 19.1 28.6 104.6 41.3 100.0 149.4 8 22.080 3" 210 90.7 20.6 31.7 127.0 46.0 117.3 168.1 8 22.090 3.1/2" 229 103.4 22.3 34.9 139.7 49.2 133.4 184.2 8 26.0

Nominal Pipe Size

Bore Dia. (B1)





23










Nominal Pipe Size

Outside Dia.


Lgth Thru Hub

Weld Point


No. of holes

Hole Dia.

mm in O T R Y A X C mm mm15 1/2" 95 14.3 35.1 22.4 21.3 38.1 66.5 4 16.020 3/4" 117 15.9 42.9 25.4 26.7 47.8 82.5 4 19.025 1" 124 17.5 50.8 27.0 33.5 54.0 88.9 4 19.032 1.1/4" 133 20.6 63.5 28.4 42.2 63.5 98.6 4 19.040 1.1/2" 155 22.2 73.2 31.7 48.3 69.9 114.3 4 22.050 2" 165 25.4 91.9 36.5 60.3 84.1 127.0 8 19.065 2.1/2" 190 28.6 104.6 41.3 73.0 100.0 149.4 8 22.080 3" 210 31.7 127.0 46.0 88.9 117.3 168.1 8 22.090 3.1/2" 229 34.9 139.7 49.2 101.6 133.4 184.2 8 26.0

100 4" 273 38.1 157.2 54.0 114.3 152.4 215.9 8 26.0125 5" 330 44.4 185.7 60.3 141.2 188.9 266.7 8 29.0150 6" 356 47.6 215.9 66.7 168.4 222.3 292.1 12 29.0200 8" 419 55.6 269.7 76.2 219.2 273.1 349.2 12 32.0250 10" 510 63.5 323.9 85.9 273.1 342.9 431.8 16 35.0300 12" 560 66.7 381.0 91.9 323.9 400.1 488.9 20 35.0

Nominal Pipe Size

Bore Dia. (B)


100 4" 108.3 102.3 97.2 87.3125 5" 134.4 128.2 122.3 109.5150 6" 161.6 154.1 146.3 131.8200 8" 211.6 202.7 193.7 173.1250 10" 264.6 254.4 247.7 215.9300 12" 314.6 304.8 298.5 257.2

24










Nominal Pipe Size

Outside Dia.


Length Thru Hub


No. of holes

Hole Dia.

mm in O B T R Y X C mm mm15 1/2" 95 22.4 14.3 35.1 22.4 38.1 66.5 4 16.020 3/4" 117 27.7 15.9 42.9 25.4 47.8 82.5 4 19.025 1" 124 34.5 17.5 50.8 27.0 54.0 88.9 4 19.032 1.1/4" 133 43.2 20.6 63.5 28.4 63.5 98.6 4 19.040 1.1/2" 155 49.5 22.2 73.2 31.7 69.9 114.3 4 22.050 2" 165 62.0 25.4 91.9 36.5 84.1 127.0 8 19.065 2.1/2" 190 74.7 28.6 104.6 41.3 100.0 149.4 8 22.080 3" 210 90.7 31.7 127.0 46.0 117.3 168.1 8 22.090 3.1/2" 229 103.4 34.9 139.7 49.2 133.4 184.2 8 26.0

100 4" 273 116.1 38.1 157.2 54.0 152.4 215.9 8 26.0125 5" 330 143.8 44.4 185.7 60.3 188.9 266.7 8 29.0150 6" 356 170.7 47.6 215.9 66.7 222.3 292.1 12 29.0200 8" 419 221.5 55.6 269.7 76.2 273.1 349.2 12 32.0250 10" 510 276.4 63.5 323.9 85.9 342.9 431.8 16 35.0300 12" 560 327.2 66.7 381.0 91.9 400.1 488.9 20 35.0






Hole Dia.

mm in O T R C mm mm15 1/2" 95 14.3 35.1 66.5 4 16.020 3/4" 117 15.9 42.9 82.5 4 19.025 1" 124 17.5 50.8 88.9 4 19.032 1.1/4" 133 20.6 63.5 98.6 4 19.040 1.1/2" 155 22.2 73.2 114.3 4 22.050 2" 165 25.4 91.9 127.0 8 19.065 2.1/2" 190 28.6 104.6 149.4 8 22.080 3" 210 31.7 127.0 168.1 8 22.090 3.1/2" 229 34.9 139.7 184.2 8 26.0

100 4" 273 38.1 157.2 215.9 8 26.0125 5" 330 44.4 185.7 266.7 8 29.0150 6" 356 47.6 215.9 292.1 12 29.0200 8" 419 55.6 269.7 349.2 12 32.0250 10" 510 63.5 323.9 431.8 16 35.0300 12" 560 66.7 381.0 488.9 20 35.0

25





Nominal Pipe Size

Outside Dia.



No. of holes

Hole Dia.

mm in O B T r Y X C mm mm15 1/2" 95 22.9 14.3 3.0 22.4 38.1 66.5 4 16.020 3/4" 117 28.2 15.9 3.0 25.4 47.8 82.5 4 19.025 1" 124 35.1 17.5 3.0 27.0 54.0 88.9 4 19.032 1.1/4" 133 43.7 20.6 5.0 28.4 63.5 98.6 4 19.040 1.1/2" 155 50.0 22.2 6.0 31.7 69.9 114.3 4 22.050 2" 165 62.5 25.4 8.0 36.5 84.1 127.0 8 19.065 2.1/2" 190 75.4 28.6 8.0 41.3 100.0 149.4 8 22.080 3" 210 91.4 31.7 10.0 46.0 117.3 168.1 8 22.090 3.1/2" 229 104.1 34.9 10.0 49.2 133.4 184.2 8 26.0

100 4" 273 116.9 38.1 11.0 54.0 152.4 215.9 8 26.0125 5" 330 143.8 44.4 11.0 60.3 188.9 266.7 8 29.0150 6" 356 170.7 47.6 13.0 66.7 222.3 292.1 12 29.0200 8" 419 221.5 55.6 13.0 76.2 273.1 349.2 12 32.0250 10" 510 276.4 63.5 13.0 85.9 342.9 431.8 16 35.0300 12" 560 327.2 66.7 13.0 91.9 400.1 488.9 20 35.0






Nominal Pipe Size

Outside Dia.

Thread Type


Length Thru Hub


No. of holes

Hole Dia.



14.3 35.1 22.4 38.1 66.5 4 16.020 3/4" 117 15.9 42.9 25.4 47.8 82.5 4 19.025 1" 124 17.5 50.8 27.0 54.0 88.9 4 19.032 1.1/4" 133 20.6 63.5 28.4 63.5 98.6 4 19.040 1.1/2" 155 22.2 73.2 31.7 69.9 114.3 4 22.050 2" 165 25.4 91.9 36.5 84.1 127.0 8 19.065 2.1/2" 190 28.6 104.6 41.3 100.0 149.4 8 22.080 3" 210 31.7 127.0 46.0 117.3 168.1 8 22.090 3.1/2" 229 34.9 139.7 49.2 133.4 184.2 8 26.0

100 4" 273 38.1 157.2 54.0 152.4 215.9 8 26.0125 5" 330 44.4 185.7 60.3 188.9 266.7 8 29.0150 6" 356 47.6 215.9 66.7 222.3 292.1 12 29.0200 8" 419 55.6 269.7 76.2 273.1 349.2 12 32.0250 10" 510 63.5 323.9 85.9 342.9 431.8 16 35.0300 12" 560 66.7 381.0 91.9 400.1 488.9 20 35.0





26





JIS 5K FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


Nominal Pipe Size Outside Dia. Bore Dia. Bolt Circle Dia. Thickness No. of holes Hole Dia.

mm in D d0 C t mm H10 3/8” 75 17.8 55 9 4 1215 1/2" 80 22.2 60 9 4 1220 3/4" 85 27.7 65 10 4 1225 1" 95 34.5 75 10 4 1232 1.1/4" 115 43.2 90 12 4 1540 1.1/2" 120 49.1 95 12 4 1550 2" 130 61.1 105 14 4 1565 2.1/2" 155 77.1 130 14 4 1580 3" 180 90.1 145 14 4 1990 3.1/2" 190 102.6 155 14 4 19

100 4" 200 115.4 165 16 8 19125 5" 235 141.2 200 16 8 19150 6" 265 166.6 230 18 8 19175 7” 300 192.1 260 18 8 23200 8" 320 218.0 280 20 8 23225 9” 345 243.7 305 20 8 23250 10" 385 269.5 345 22 12 23300 12" 430 321.0 390 22 12 23

Standard/ApprovalJIS B2220 KS B1519Available MaterialSS400 SUS304/316


Pressure Rating5 kg/cm2

Flange TypesSlip-on Plate (SOP) Slip-on Hub (SOH) Blind (BL) JIS 5K SLIP-ON PLATE (SOP) FLANGE

Nominal Pipe Size

Outside Dia.

Bore Dia.

Bolt Circle Dia.

Hub Dia. Radius Lgth Thru Hub

Thickness No. of holes

Hole Dia.

mm in D D0 C A B r T t mm H10 3/8” 75 17.8 55 23 26 4 13 9 4 1215 1/2" 80 22.2 60 27 30 4 13 9 4 1220 3/4" 85 27.7 65 33 36 4 15 10 4 1225 1" 95 34.5 75 41 44 4 17 10 4 1232 1.1/4" 115 43.2 90 50 53 4 19 12 4 1540 1.1/2" 120 49.1 95 56 60 4 20 12 4 1550 2" 130 61.1 105 69 73 4 24 14 4 1565 2.1/2" 155 77.1 130 86 91 4 27 14 4 1580 3" 180 90.1 145 99 105 4 30 14 4 19

100 4" 200 115.4 165 127 130 4 36 16 8 19125 5" 235 141.2 200 154 161 4 40 16 8 19150 6" 265 166.6 230 182 189 4 40 18 8 19

Standard/ApprovalJIS B2220 KS B1519

Available MaterialSS400 SUS304/316



Flange TypesSlip-on Plate (SOP) Slip-on Hub (SOH) Blind (BL) JIS 5K SLIP-ON HUB (SOH) FLANGE

27








Nominal Pipe Size Outside Dia. Bolt Circle Dia. Thickness No. of holes Hole Dia.

mm in D C t mm H10 3/8” 75 55 9 4 1215 1/2" 80 60 9 4 1220 3/4" 85 65 10 4 1225 1" 95 75 10 4 1232 1.1/4" 115 90 12 4 1540 1.1/2" 120 95 12 4 1550 2" 130 105 14 4 1565 2.1/2" 155 130 14 4 1580 3" 180 145 14 4 1990 3.1/2" 190 155 14 4 19

100 4" 200 165 16 8 19125 5" 235 200 16 8 19150 6" 265 230 18 8 19175 7” 300 260 18 8 23200 8" 320 280 20 8 23225 9” 345 305 20 8 23250 10" 385 345 22 12 23300 12" 430 390 22 12 23



Flange TypesSlip-on Plate (SOP) Slip-on Hub (SOH) Blind (BL) JIS 5K BLIND (BL) FLANGE

28








mm in D d0 C t mm H10 3/8” 90 17.8 65 12 4 1515 1/2" 95 22.2 70 12 4 1520 3/4" 100 27.7 75 14 4 1525 1" 125 34.5 90 14 4 1932 1.1/4" 135 43.2 100 16 4 1940 1.1/2" 140 49.1 105 16 4 1950 2" 155 61.1 120 16 4 1965 2.1/2" 175 77.1 140 18 4 1980 3" 186 90.0 150 18 8 1990 3.1/2" 195 102.6 160 18 8 19

100 4" 210 115.4 175 18 8 19125 5" 250 141.2 210 20 8 23150 6" 280 166.6 240 22 8 23175 7” 305 192.1 265 22 12 23200 8" 330 218.0 290 22 12 23225 9” 350 243.7 310 22 12 23250 10" 400 269.5 355 24 12 25300 12" 445 321.0 400 24 16 25





Nominal Pipe Size

Outside Dia.

Bore Dia.

Bolt Circle Dia.



Hole Dia.

mm in D D0 C A B r T t mm H10 3/8” 90 17.8 65 23 26 4 16 12 4 1515 1/2" 95 22.2 70 27 30 4 16 12 4 1520 3/4" 100 27.7 75 33 36 4 20 14 4 1525 1" 125 34.5 90 41 44 4 20 14 4 1932 1.1/4" 135 43.2 100 50 53 4 22 16 4 1940 1.1/2" 140 49.1 105 56 60 4 24 16 4 1950 2" 155 61.1 120 69 73 4 24 16 4 1965 2.1/2" 175 77.1 140 86 91 4 27 18 4 1980 3" 186 90.0 150 99 105 4 30 18 8 19

100 4" 210 115.4 175 127 130 4 36 18 8 19125 5" 250 141.2 210 154 161 4 40 20 8 23150 6" 280 166.6 240 182 189 4 40 22 8 23






29





JIS 10K FLANGE FLUID-TEC



mm in D C t mm H10 3/8” 90 65 12 4 1515 1/2" 95 70 12 4 1520 3/4" 100 75 14 4 1525 1" 125 90 14 4 1932 1.1/4" 135 100 16 4 1940 1.1/2" 140 105 16 4 1950 2" 155 120 16 4 1965 2.1/2" 175 140 18 4 1980 3" 186 150 18 8 1990 3.1/2" 195 160 18 8 19

100 4" 210 175 18 8 19125 5" 250 210 20 8 23150 6" 280 240 22 8 23175 7” 305 265 22 12 23200 8" 330 290 22 12 23225 9” 350 310 22 12 23250 10" 400 355 24 12 25300 12" 445 400 24 16 25





30








mm in D d0 C t mm H10 3/8” 90 17.8 65 12 4 1515 1/2" 95 22.2 70 12 4 1520 3/4" 100 27.7 75 14 4 1525 1" 125 34.5 90 14 4 1932 1.1/4" 135 43.2 100 16 4 1940 1.1/2" 140 49.1 105 16 4 1950 2" 155 61.1 120 16 8 1965 2.1/2" 175 77.1 140 18 8 1980 3" 200 90.0 160 20 8 2390 3.1/2" 210 102.6 170 20 8 23

100 4" 225 115.4 185 22 8 23125 5" 270 141.2 225 22 8 25150 6" 305 166.6 260 24 12 25200 8" 350 218.0 305 26 12 25250 10" 430 269.5 380 28 12 27300 12" 480 321.0 430 30 16 27





Nominal Pipe Size

Outside Dia.

Bore Dia.

Bolt Circle Dia.



Hole Dia.

mm in D D0 C A B r T t mm H10 3/8” 90 17.8 65 26 28 4 16 12 4 1515 1/2" 95 22.2 70 30 32 4 16 12 4 1520 3/4" 100 27.7 75 38 42 4 20 14 4 1525 1" 125 34.5 90 46 50 4 20 14 4 1932 1.1/4" 135 43.2 100 56 60 5 22 16 4 1940 1.1/2" 140 49.1 105 62 66 5 24 16 4 1950 2" 155 61.1 120 76 80 5 24 16 8 1965 2.1/2" 175 77.1 140 94 98 5 26 18 8 1980 3" 200 90.0 160 108 112 6 28 20 8 2390 3.1/2" 210 102.6 170 120 124 6 30 20 8 23

100 4" 225 115.4 185 134 138 6 34 22 8 23125 5" 270 141.2 225 164 170 6 34 22 8 25150 6" 305 166.6 260 196 202 6 38 24 12 25200 8" 350 218.0 305 244 252 6 40 26 12 25250 10" 430 269.5 380 304 312 6 44 28 12 27300 12" 480 321.0 430 354 364 8 48 30 16 27






31





JIS 16K FLANGE FLUID-TEC



mm in D C t mm H10 3/8” 90 65 12 4 1515 1/2" 95 70 12 4 1520 3/4" 100 75 14 4 1525 1" 125 90 14 4 1932 1.1/4" 135 100 16 4 1940 1.1/2" 140 105 16 4 1950 2" 155 120 16 8 1965 2.1/2" 175 140 18 8 1980 3" 200 160 20 8 2390 3.1/2" 210 170 20 8 23

100 4" 225 185 22 8 23125 5" 270 225 22 8 25150 6" 305 260 24 12 25200 8" 350 305 26 12 25250 10" 430 380 28 12 27300 12" 480 430 30 16 27





32






mm in D k b mm d2

10 3/8” 90 60 14 4 1415 1/2" 95 65 14 4 1420 3/4" 105 75 16 4 1425 1" 115 85 16 4 1432 1.1/4" 140 100 16 4 1840 1.1/2" 150 110 16 4 1850 2" 165 125 18 4 1865 2.1/2" 185 145 18 4 1880 3" 200 160 20 8 18

100 4" 220 180 20 8 18125 5" 250 210 22 8 18150 6" 285 240 22 8 22200 8" 340 295 24 8 22250 10" 395 350 26 12 22300 12" 445 400 26 12 22

Standard/Approval

DIN EN1092-1 DIN 2501-1Available MaterialA105N SS304/316


Flange Types

Slip-on (SOFF) Blind (BLFF) Welded Neck (WNRF)

DIN PN10 BLIND (BLFF) FLANGE

DIN PN10 FLANGE FLUID-TEC Fluid-Tec Engineering & Trading Pte Ltd ● Address : No. 5 Kian Teck Way Singapore 628733


Nominal Pipe Size Outside Dia. Bore Dia. Bolt Circle Dia.

Thickness No. of holes Hole Dia.

mm in D d1 (ISO) d1 (DIN) k b mm d2

10 3/8” 90 17.2 14.0 60 14 4 1415 1/2" 95 21.3 20.0 65 14 4 1420 3/4" 105 26.9 25.0 75 16 4 1425 1" 115 33.7 30.0 85 16 4 1432 1.1/4" 140 42.4 38.0 100 16 4 1840 1.1/2" 150 48.3 44.5 110 16 4 1850 2" 165 60.3 57.0 125 18 4 1865 2.1/2" 185 76.1 - 145 18 4 1880 3" 200 8.9 - 160 20 8 18

100 4" 220 114.3 108.0 180 20 8 18125 5" 250 139.7 133.0 210 22 8 18150 6" 285 168.3 159.0 240 22 8 22200 8" 340 219.1 - 295 24 8 22250 10" 395 273.0 267.0 350 26 12 22300 12" 445 323.9 - 400 26 12 22

Standard/ApprovalDIN EN1092-1 DIN 2501-1Available MaterialA105N SS304/316


Flange TypesSlip-on (SOFF) Blind (BLFF) Welded Neck (WNRF)

DIN PN10 SLIP-ON PLATE (SOP) FLANGE

33







Nominal Pipe Size

Outside Dia.

Neck Radius Neck Lgth

Lgth Thru Hub

Raised Face Dia.

Height of Raised Face

Bolt Circle Dia.

Thickness

mm in D s r h2 h1 d4 f k b10 3/8” 90 1.8 4 6 35 40 2 60 1415 1/2" 95 2.0 4 6 35 45 2 65 1420 3/4" 105 2.3 4 6 38 58 2 75 1625 1" 115 2.6 4 6 38 68 2 85 1632 1.1/4" 140 2.6 6 6 40 78 2 100 1640 1.1/2" 150 2.6 6 7 42 88 3 110 1650 2" 165 2.9 6 8 45 102 3 125 1865 2.1/2" 185 2.9 6 10 45 122 3 145 1880 3" 200 3.2 8 10 50 138 3 160 20

100 4" 220 3.6 8 12 52 158 3 180 20125 5" 250 4.0 10 12 55 188 3 210 22150 6" 285 4.5 10 12 55 212 3 240 22200 8" 340 5.9 12 16 62 268 3 295 24250 10" 395 6.3 12 16 68 320 3 350 26300 12" 445 7.1 12 16 68 370 4 400 26




DIN PN10 WELDED-NECK (WNRF) FLANGE

Nominal Pipe Size

Bevel & Hub Dia. No. of holes

Hole Dia.

mm in d1 (ISO) d3 (ISO) d1 (DIN) d3 (DIN) mm d2

10 3/8” 17.2 28.0 14 25 4 1415 1/2" 21.3 32.0 20 30 4 1420 3/4" 26.9 40.0 25 38 4 1425 1" 33.7 45.0 30 42 4 1432 1.1/4" 42.4 56.0 38 52 4 1840 1.1/2" 48.3 64.0 45 60 4 1850 2" 60.3 75.0 57 72 4 1865 2.1/2" 76.1 90.0 - - 4 1880 3" 8.9 105.0 - - 8 18

100 4" 114.3 131.0 108 125 8 18125 5" 139.7 156.0 133 150 8 18150 6" 168.3 184.0 159 175 8 22200 8" 219.1 235.0 - - 8 22250 10" 273.0 292.0 267 285 12 22300 12" 323.9 344.0 - - 12 22

34






mm in D k b mm d2

10 3/8” 90 60 14 4 1415 1/2" 95 65 14 4 1420 3/4" 105 75 16 4 1425 1" 115 85 16 4 1432 1.1/4" 140 100 16 4 1840 1.1/2" 150 110 16 4 1850 2" 165 125 18 4 1865 2.1/2" 185 145 18 4 1880 3" 200 160 20 8 18

100 4" 220 180 20 8 18125 5" 250 210 22 8 18150 6" 285 240 22 8 22200 8" 340 295 24 12 22250 10" 405 355 26 12 26300 12" 460 410 28 12 26

Standard/Approval

DIN EN1092-1 DIN 2501-1Available MaterialA105N SS304/316


Flange Types

Slip-on (SOFF) Blind (BLFF) Welded Neck (WNRF)

DIN PN16 BLIND (BLFF) FLANGE



Nominal Pipe Size Outside Dia. Bore Dia. Bolt Circle Dia.

Thickness No. of holes Hole Dia.

mm in D d1 (ISO) d1 (DIN) k b mm d2

10 3/8” 90 17.7 14.5 60 14 4 1415 1/2" 95 22.0 21.0 65 14 4 1420 3/4" 105 27.6 26.0 75 16 4 1425 1" 115 34.4 31.0 85 16 4 1432 1.1/4" 140 43.1 39.0 100 16 4 1840 1.1/2" 150 49.0 45.5 110 16 4 1850 2" 165 61.1 58.1 125 18 4 1865 2.1/2" 185 7.1 - 145 18 4 1880 3" 200 90.3 - 160 20 8 18

100 4" 220 115.9 109.6 180 20 8 18125 5" 250 141.6 134.8 210 22 8 18150 6" 285 170.5 161.1 240 22 8 22200 8" 340 221.8 295 24 12 22250 10" 405 276.2 270.2 355 26 12 26300 12" 460 327.6 - 410 28 12 26




DIN PN16 SLIP-ON PLATE (SOP) FLANGE

35







Nominal Pipe Size

Outside Dia.

Neck Radius Neck Lgth

Lgth Thru Hub

Raised Face Dia.

Raised Face Height

Bolt Circle Dia.

Thickness

mm in D s r h2 h1 d4 f k b10 3/8” 90 1.8 4 6 35 40 2 60 1415 1/2" 95 2.0 4 6 35 45 2 65 1420 3/4" 105 2.3 4 6 38 58 2 75 1625 1" 115 2.6 4 6 38 68 2 85 1632 1.1/4" 140 2.6 6 6 40 78 2 100 1640 1.1/2" 150 2.6 6 7 42 102 3 110 1650 2" 165 2.9 6 8 45 122 3 125 1865 2.1/2" 185 2.9 6 10 45 138 3 145 1880 3" 200 3.2 8 10 50 158 3 160 20

100 4" 220 3.6 8 12 52 188 3 180 20125 5" 250 4.0 8 12 55 212 3 210 22150 6" 285 4.5 10 12 55 268 3 240 22200 8" 340 5.9 10 16 62 320 3 295 24250 10" 405 6.3 12 16 70 378 3 355 26300 12" 460 7.1 12 16 78 438 4 410 28




DIN PN16 WELDED-NECK (WNRF) FLANGE

Nominal Pipe Size

Bevel & Hub Dia. No. of holes

Hole Dia.

mm in d1 (ISO) d3 (ISO) d1 (DIN) d3 (DIN) mm d2

10 3/8” 17.2 28.0 14 25 4 1415 1/2" 21.3 32.0 20 30 4 1420 3/4" 26.9 40.0 25 38 4 1425 1" 33.7 45.0 30 42 4 1432 1.1/4" 42.4 56.0 38 52 4 1840 1.1/2" 48.3 64.0 45 60 4 1850 2" 60.3 75.0 57 72 4 1865 2.1/2" 76.1 90.0 - - 4 1880 3" 88.9 105.0 - - 8 18

100 4" 114.3 131.0 108 125 8 18125 5" 139.7 156.0 133 150 8 18150 6" 168.3 184.0 159 175 8 22200 8" 219.1 235.0 - - 12 22250 10" 273.0 292.0 267 285 12 26300 12" 323.9 344.0 - - 12 26

36





Documents

FLANGES MASTER CATALOG - Fluid-Tec · SAE J518 FLANGE JIS B2291 SQUARE FLANGE ANSI B16.5 FLANGE JIS B2220 FLANGE DIN FLANGE. CONTENT PAGE FLUID-TEC Fluid-Tec Engineering & Trading