Upload
buikhanh
View
295
Download
4
Embed Size (px)
Citation preview
Fixings
Fixings OfferTIMBER SCREWS METAL SCREWS ROOFING SCREWS
COLLATED SCREWS
COLLATED NAILS
RIVETS BOLTS
PA TOOLS
NAILS
JOIST HANGERSCONNECTORS POST SUPPORTS
MASONRY CHEMICALS PLASTER
DECKING SCREWS
Screws
Screw Selection GuideHead Styles
Hexagon Head with Washer FaceTo accommodate a watertight sealing washer.
Wafer HeadA versatile low head style used for many fastening applications. #2 Phillips Cross Head Bit.
Pan Head Designed for applications fixing against metal surfaces. #2 Phillips Cross Head Bit.
Button HeadLow profile head enables fastener to sit level on surface. #2 Phillips Cross Bit of #2 Square Drive Bit.
Bugle HeadSmooth curved surface under head is designed to avoid damage to plasterboard. #2 Phillips Cross Head Bit.
Bugle Head BattenFor a flush finish into timber. For fastening battens to timber rafters. 5mm internal hexagon drive bit.
Countersunk HeadFor countersinking into timber for a flush or recessed finish. #2 Phillips Cross Head Bit or #2 Square Drive Bit.
Self Embedding HeadDesigned to ream into sheeting or hardwoods. #2 Phillips Cross Head Bit.
Screw Selection GuideCoatings
Zinc Plated (ZP): Internal Use An electroplated zinc coating.
Gold Passivated (GP): Internal UseChromate film over zinc for a higher corrosion protection.
Galvanised (Gal): Class 3Mechanically applied zinc, suitable for external use.
Tin/Zinc (TZ): Class 3Combines tin & zinc, suitable for external use
Zinc Alloy (ZA): Class 3Similar coating to Tin/Zinc, suitable for external use.
Tufcote (TC): Class 3Suitable for treated pine use. Consists of a sacrificial zinc base coat with organic top coat for protection against timber treatments.
Climacoat (CC): Class 3Suitable for treated pine use. Consists of a sacrificial zinc base coat with organic top coat for protection against timber treatments.
Climaseal 3 (CS3): Class 3A coating that meets AS3566.2-2002 Class 3 under real world testing.
Climaseal 4 (CS4): Class 4A coating that meets AS3566.2-2002 Class 4 under real world testing.
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occurs.Class 3: For external use in mild industrial and moderate marine applications.Class 4: For external use in moderate and severe marineenvironments (generally from 100m to 300m from the beach front).
Screws
CHIPBOARD DECKINGTIMBER
METAL
TREATED PINEPLASTERBOARD
ROOFING CYCLONE ASSEMBLIES
POLYCARBONATE COLLATED SCREWS
Timber Screws
Self drilling screws for fixing into timber and thin steel thicknesses up to 0.75mm battens.
Bugle Head BattenFixing roofing battens or fastening heavy timbers where a flush finish is required – fencing – pergolas - boardwalk. Type 17 point. ZP, TZ, ZA3, Climacoat3.
Countersunk Head Jobs needing a flush finish – hinges – furniture – brackets. Type 17 point. ZP, TZ.
Self Embedding HeadGeneral fixing – walls – wet area linings - particleboard flooring. Type 17 point. ZP, TZ.
Button Head Stitching ScrewsWhere a broad, flat head is needed, e.g. shade cloth, foil insulation, wire mesh, etc. Needle point. ZP, TZ.
Wafer Head ScrewsJobs needing a low profile head – metal deck clips – electrical fittings – signs. Type 17 point. ZP, TZ.
Fixing to Timber
Timber Screws
Self drilling screws for fixing into timber and thin steel battens to 0.75mm thick.
Hex Head - No Seal (Part Thread)For fixing timber or thin steel – vertical cladding - furniture –pergolas – gates & fences. Type 17 point. TZ, Climaseal® 3.
Hex Head – No Seal (Full Thread)For fixing timber or thin steel – vertical cladding – furniture –pergolas – gates & fences. Type 17 point. TZ, Climaseal® 3.
Hex Head - With Seal (Part Thread)For crest fixing roofing profiles to timber battens. Type 17 point. TZ, Climaseal® .
Hex Head - With Seal (Full Thread)For valley fixing wall cladding. Type 17 point. TZ, Climaseal® 3 .
Fixing to Timber
Chipboard Screws
Chipboard Screws have a course thread and fine shank to provide maximum grip and minimum strip-out into chipboard, MDF board and soft timbers.
Countersunk Rib HeadFor general fixing – cabinets – furniture – kitchens –office partitioning. Available in Phillips Drive and Square Drive. GP & GAL finishes.
Fixing to Timber
Plasterboard Screws feature a bugle shaped head which countersinks neatly into plasterboard without crushing the core, or tearing the face paper.
Bugle Head – Needle PointFor fixing plasterboard to timber – wall and ceilings – partitions. GP finish.
Bugle Head – Teks / Drill PointFor fixing plasterboard to metal. GP finish.
Fixing to Timber & Metal
Plasterboard Screws
Decking Screws
For fixing to treated pine and hardwood decking for a flush finish. When fixing hardwood timbers, pre-drilling is recommended.
Countersunk Rib Head – Square DriveSuitable for decking using most treated pine and hardwood timbers. Pre-drilling required. Available in; - Climacoat 3 , Stainless Steel Grade 303 & 316
QuickShotTM Self Drilling – Square DriveSuitable for use in treated pine and hardwood decking. - Stainless Steel grade 304 and Tufcote
Bugle Head Batten – Internal Hex DriveSuitable for decking, boardwalks, landscaping and outdoor furniture. - TZ, ZA3, Climacoat 3, Stainless Steel Grade 302 & 316
Fixing to Timber
Treated Pine Screws
For general fixing to treated timber – trellis, outdoor furniture, fencing, lattice, etc. Finished in Tufcote® (Zenith) and Climacoat® (Buildex) to resist the corrosive effects of timber treatments.
Countersunk Rib Head – Phillips Drive
- Tufcote® (Zenith)- Climacoat® (Buildex)
Countersunk Rib Head – Square Drive
- Tufcote® (Zenith)
Fixing To Treated Pine
Metal Screws - Teks®
Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel.
Bugle Head Teks® Fixing plasterboard to metal. TZ finish.
Countersunk Head Teks® Jobs needing a flush finish – fencing – gates - hinges. ZP, TZ.
Countersunk Head – Wing Teks®Fixing timber and composite boards to metal – prevents timber rising to the top of the screw while the metal is being drilled. ZP, TZ, Climacoat3 .
Button Head Teks® Where a broad flat head is needed– foil sarking – insulation panels –
facsia bracket clips, etc. ZP, TZ finishes.
Wafer Head Teks® Jobs needing a low profile head – metal deck clips – electrical fittings – signs – sheet metal. Zinc plated, Tin/Zinc finish
Fixing to Metal
Metal Screws - Teks®
Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel.
Hex Head Teks® - No Seal (Part Thread)For fixing metal to metal – fences – signs – fixings - trailers. TZ, Climaseal® 3 finishes.
Hex Head Teks® – No Seal (Full Thread)For fixing metal to metal – fences – signs – fixings - trailers. TZ, Climaseal® 3 finishes.
BattenZips® - MetalFor fixing roofing profiles and cladding to lightweight 0.75mm metal battens. Climaseal® 3 finish.
PolyZips® – Timber or MetalFor fixing polcarbonate sheeting to timber or metal purlins. Hex Head with Dome Washer & Cutter. Climaseal® 3 finish
Fixing to Metal
Roofing Screws
Roof Zips® – Timber or MetalEasier to use, faster to install, RoofZips® are used for fixing steel roof sheeting to timber, to thin metal battens or steel purlins up to 1.9mm thick. Climaseal® 4 coating which meets AS3566 Class 4.
Hex Head Teks® - With Seal (Part Thread)Fixing roofing profiles and wall cladding to steel purlins. TZ, Climaseal® 3 and Climaseal® 4 finishes.
Hex Head Teks® - With Seal (Full Thread)Fixing roofing profiles and wall cladding to steel purlins. TZ, Climaseal® 3 and Climaseal® 4 finishes.
Hex Head Teks® – HiGrip With SealFor crest fixing corrugated and square rib roofing profiles to steel purlins. TZ, Climaseal® 3 and Climaseal® 4 finishes.
Fixing to Timber & Metal
Roofing Screws
- Cyclone Assemblies
CORRI-LOK® - Available in Type 17 & Metal Teks® Fixing corrugated roofing profile to timber battens and steel purlins in cyclonic areas. Climaseal® 4 coating
SQUARE-LOK® - Type 17 & Metal Teks® Fixing square rib roofing profiles to timber battens and steel purlins in cyclonic areas. Climaseal® 4 coating
High Rib Profiles – Type17 & Metal Teks® Fixing high rib roofing profiles to timber battens and steel purlins in cyclonic areas. Climaseal® 4 coating
Ridge Cap Assemblies – Type 17 & Metal Teks® For ridge cap assembly of roofing profiles to timber battens and steel purlins in cyclonic areas. Climaseal® 4 coating
Fixing to Timber & Metal
Collated Screws
Self Drilling Plasterboard Screws
Designed for fixing plasterboard to timber or light gauge
steel.
Self Drilling Metal Screws
Drill, tap and fasten into steel up to 6mm thick in one single
operation, eliminating alignment problems and increasing
fastening speed.
Self Drilling Particleboard Screws
Designed for attaching particleboard and soft timbers to
particleboard or soft timbers. Ideal for furniture, cabinet
making and office partitioning applications.
Self Drilling Cabinet Screws
Designed for attaching particleboard, timber, insulation foil
or sheet metal to timber.
Construction Fasteners
Open Rivets
Multi-Grip Rivets
One size handles the grip range capacity of up to 3 standard open end rivets using a standard riveting tool. They can clamp a wide range of material thickness, reduce inventory requirements, provide superior clamping and high strength, have high vibration resistance and completely fill the hole during riveting.
Sealed RivetsAre ideal where an application has to be water or pressure tight. Sealed rivets have 100% mandrel retention, so give a higher tensile and shear loading performance than open type rivets.
Fixing to Metal
Provide an economical means for permanent fastening light gauge metal parts.
Blind RivetsFor low cost, reliable fastening of light gauge materials where access to the rear or “blind side” of joint is not accessible.
BLIND
RIVETS
RIVET
MATERIAL
MANDREL
MATERIAL
COLOUR
CODE
Open
AluminiumZinc Plated
SteelRed
Zinc Plated
Steel
Zinc Plated
SteelGreen
Stainless Steel
304
Stainless Steel
304Blue
Sealed AluminiumZinc Plated
SteelPurple
Multi-
GripAluminium
Zinc Plated
SteelYellow
RIVET
MATERIA
L
COMPATABLE METALS FOR FASTENING
AluminiumAluminiu
m
Aluminium/Zinc
Plated Steel
Zinc Plated
Steel(mild environments only)
Zinc
Plated
Steel
Aluminium/Zinc
Plated Steel
Zinc Plated
Steel
Stainless
Steel 304
Stainless
SteelCopper Brass
Bolts & Coach Screws
Cup HeadIdeal for fastening timber to timber. “Square neck” feature limits bolt from spinning when tightening nut.
Hex HeadIdeal for fastening metal to metal. Useful in most general bolt applications.
Coach ScrewsIdeal for fastening timber to timber. “Gimlet Point” allows for easy application into timber.
Fixing to Timber & Steel
Zinc Plated Hot Dipped Galvanised Tech-Shieldᵀᵀ Stainless Steel
For internal applications such as furniture construction and garage work benches.
Provides additional protection against outside elements, limiting corrosion.
Protects the bolt fromthe chemicals found in CCA and ACQ treated pine, hence prolongs the life of the bolt.
Stainless Steel is a premium bolt materialthat is suitable for highly corrosive areas (EG. coastal).
* All Zenith Bolts are made to Australian or DIN standards.
Nails
SHEETINGGENERAL PURPOSE
DECKING TIMBER CONNECTOR
SPECIALTY
General Purpose Nails
Bullet Head NailsGeneral purpose nails for fixing timber to timber. Available in Bright Steel, Galvanised finish and Stainless Steel.
Flat Head NailsLarge head to avoid pull though in soft timbers. Available in Bright Steel, Galvanised finish and Stainless Steel.
CloutsFor fixing thin sheet metal to timber. Wide flat head prevents pull through. Available in Galvanised finish.
Fixing to Timber
Decking Nails
Decking (GripLock) Nails Used for fixing timber to timber for heavy duty landscaping & decking applications. Available in Galvanisedfinish and Stainless Steel.
Decking SpikesFor fixing large section timbers, treated pine of hardwood sleepers. Available in Galvanised finish.
Fixing to Timber
Sheeting Nails
Fibre Cement NailsFor fixing cement sheet lining board to timber framework. Available in Galvanised finish and Stainless Steel.
Particle Board NailsFor fixing particle board sheet, specifically for internal linings and flooring. Available in Bright Steel and Gold Passivated finish.
Soft Sheet NailsFor fixing plywood sheet. Available in Zinc Plated.
Hardboard NailsFor fixing hardboard linings – dense and compressed . Available in Zinc Plated.
Fixing to Timber
Sheeting Nails
Underlay / Fibre Cement NailsFor fixing fibre cement underlay sheet to timber flooring. Available in Bright Steel.
Underlay / Hardboard NailsFor fixing hardboard underlay sheet to timber flooring. Available in Bright Steel.
Wall Board NailsFor fixing wallboard to timber frame. Available in Zinc Plated.
Plasterboard NailsFor fixing plasterboard to timber framework. Available in Zinc Plated.
Fixing to Timber
Timber Nail Connectors
Bracket Plain ShankFor fixing brackets and timber connectors. Available in Galvanised finish.
Bracket Helical ShankWith helical thread for greater holding power. Available in Galvanised finish.
Strapping Designed for fixing thin metal strapping. Available in Galvanised finish and Stainless Steel 316 grade.
Fixing to Timber
(3.75mm diameter)
(2.8mm diameter)
Specialty Nails
Blue Cut TacksLarge headed nails used to hold floor coverings or upholstery work.
Upholstery For fixing fabric/furniture coverings to timber.
Staples – Plain / BarbedU-shaped, double ended nail, used fixing mesh or shade cloth to timber.
Corrugated FastenersDesigned for joining across timber face
Fixing to Timber
Specialty Nails
Roofing Nails – Plain ShankPlain shank connector used for fixing external roofing or cladding. Available in Galvanised finish.
Roofing Nails –Twisted ShankTwisted shank for extra holding power. Available in Galvanised finish.
Concrete NailsUsed for fixing timber to freshly laid concrete. Available in Zinc Plated.
SkirtingFor fixing skirting board to brick or masonry walls. Available in Zinc Plated.
Fixing to Timber
Masonry & Plasterboard Anchors
CHEMICALSEXPANSIONDynaBoltᵀᵀ AnkaScrewᵀᵀ
NYLON RAMPLUGS WALL PLUGS
PA TOOLS & ACCESSORIES
MASONRY NAILS
WallMateᵀᵀ TOGGLESHOLLOW WALL
DynaBoltᵀᵀ Plus
DynaBoltᵀ PTlus is a patented design sleeve anchor with the unique ability to “pull down”
and ensure a tight and secure anchoring to the fixture. For medium duty anchoring of
timber and steel fixtures to concrete.
- Hex Head
- Flush Head
- Flat Head
- Round Head
- Eye Bolt
- Hook Bolt
Available in diameters of 6 through to 20mm;
in yellow passivated zinc, hot dip galvanised finish and stainless steel AISI 316.
Fixing to Masonry
AnkaScrewᵀᵀ
The AnkaScrewᵀᵀScrew-In Anchor is a medium duty,
rotation setting thread forming anchor. It’s fast and easy
to install, easy to remove and does not expand or burst
substrate allowing close to edge installation. Suitable for
solid concrete, masonry and hollow brick and block.
Hex Head, WERCS™ Thread
Available in 6 through to 12mm in diameter, up to 150mm
in length; in zinc passivated and galvanised finishes.
Fixing to Masonry
Expansion Anchors
TruBoltᵀᵀ Stud Anchors
TruBoltᵀᵀ is a heavy duty torque setting expansion anchor for
permanent anchoring into solid substrates such as concrete.
Loxinᵀᵀ Shield AnchorsThe Loxinᵀᵀ is a shorter length, internally threaded anchor for use
with machine bolts and threaded rod into solid substrates such as
concrete, brick, block and stone.
ShureDriveᵀᵀSureDriveᵀᵀ is a nail in expansion anchor providing a tamper
proof anchor into solid concrete or masonry.
Fixing to Masonry
ChemSetᵀ 1T01 Plus 400ml / 750mml
A fast curing multi purpose chemical mortar for anchoring
into solid concrete and masonry or hollow brick and
concrete block.
Styrene free and low odor. Versatile, multi-purpose two
part polyester anchoring system.
Fast cure for high productivity. Non-drip formula, ideal for
overhead installation.
Chemical Anchors
Fixing to Masonry
Chemical Anchors
ChemSetᵀ 8T01 400ml / 750ml
Fixing to Masonry
A high performance chemical resistant vinyl ester
adhesive. Heavy duty anchoring of threaded studs
and reinforcing bar into solid concrete and stone.
Fast cure, chemical resistant and suitable for
contact with drinking water.
Tough and reliable for extra security.
CHEMICAL ANCHORS
ChemSetᵀᵀ Maximaᵀᵀ Capsules
Rapid cure, extra heavy duty anchoring
of threaded studs into solid concrete and
stone. For small jobs with few fixings.
One capsule for one hole - no mixing,
no mess, no waste.
UltraFixᵀ PTlus
Ultrafix ᵀᵀ Plus is a fast curing adhesive for
anchoring threaded rod and studs.
Available in convenient 300ml cartridge with
2 nozzles. Fits a standard calking gun.
Fixing to Masonry
Chemical Anchoring Accessories
Mixer NozzlesTwo types available, suitable for vinyl ester and polyester
Chemsetᵀᵀ Universal Applicator Gun
Hole Cleaning BrushesAvailable in 3 sizes(8-12mm, 16-20mm, 20-24mm)
Hole Cleaning Pump
ChemSetᵀᵀ Anchor StudsAvailable in M8 through to M24 and length up to
300mm; in zinc plated, hot dip galvanised and stainless steel 316.
Fixing to Masonry
Nylon Anchors
Nylon AnchorsLight duty removable expansion anchors for use in solid
concrete and masonry.
Countersunk Head Mushroom Head Round Head
EasyDriveᵀᵀ Anchors Light duty removable expansion anchors for use in solid
concrete and masonry.
Available in zinc plated steel and stainless steel.
Fixing to Masonry
RamPlugᵀᵀ Anchors
RamPlugᵀᵀ Anchors – StandardRamplug provides a medium duty screw anchoring point
into concrete, hollow brick and for light duty applications into
lightweight concrete.
RamPlugᵀᵀ Anchors – Long Plug
RamPlugᵀᵀ Anchors – Ultra Long Plug with ScrewAvailable with flat and hex head screws, in yellow passivated
zinc and galvanised finishes.
Fixing to Masonry
Wall Plugs
Wall PlugsAn inexpensive expansion plug for use with screws.
Wall Plug is also available in rolls of 5m length.
White (5mm), Red (6mm), Green (7mm), Blue (8mm)
Plastic SpaghettiUsed with 4.5-6g screws and nails.
Fixing to Masonry
Concrete Nails
Concrete Nails without Washer
Concrete Nails with Washer
Concrete Nails with Striated Shank
Fixing to Masonry
For hand hammer driving into concrete and solid brick. Ramset™ concrete nails are manufactured from
ductile, high strength carbon steel and are available in a number of different styles to suit a range of
applications.
Powder Actuated Tools &
Accessories
Fixing to Masonry
FrameMaster™ TS750P
A power adjustable tool designed for fixing timber
framing to concrete and general repetitive work.
FrameMaster™ Accessories
• Drive Pins
For fastening to standard strength concrete,
masonry and steel up to a maximum of 8mm.
• Power Load Strip (Yellow)
JobMaster™
An all round, powerful general purpose
tool for the less frequent user – essential for every
contractor’s toolbox.
JobMaster™ Accessories
• Drive Pins
For fastening to standard strength concrete,
masonry and steel up to a maximum of 8mm.
•Power Load Cartridges
Available in green, yellow and red.
Fixing to Masonry
FormMaster™
High powered fastening system with the power
and comfort to meet the demands of the timber
and steel formwork industry and heavier repetitive
fixing jobs.
FormMaster™ Accessories
• Drive Pins
For fastening to standard strength concrete,
masonry and steel up to a maximum of 8mm.
• Power Load Strip (Red & Yellow)
Fixing to Masonry
Frameboss™ Is a fully automatic powder actuated tool, which is
capable of fixing 10 pins without the need to reload or
cycle the tool.
With a huge 380 Joules of impact energy coupled
with power adjustment, the tool can be used in a wide
variety of applications
FrameBoss™ Accessories
• Collated Drive Pins
For fastening to standard strength concrete, masonry
and steel up to a maximum of 8mm.
• Power Load Strip (Red & Yellow)
Fixing to Masonry
WallMateᵀᵀ
Nylon Medium duty applications, up to 7kg - bathroom, & garage
fixtures, mirrors & clocks,
MetalMedium duty applications, up to 7kg - curtain rods, coat
racks, paintings, etc.
Nylon MiniLight duty applications up to 5kg – pictures, clocks, doorbells
Metal MiniLight duty applications up to 5kg – wall phones, smoke
detectors,
ToggleMateᵀᵀHeavy duty applications up to 11kg – shelving, mirrors, coat
racks.
NB. Loads are based on application into 10mm plasterboard.
Fixing to Plasterboard
Hollow wall Anchors
Hollow Wall AnchorsSuitable for light to medium duty applications such as
bathroom, kitchen and ceiling fixtures, shelving brackets, etc.
Available for wall thicknesses from 5mm to 38mm thick.
Hollow Wall Anchor Setting Tool
Fixing to Plasterboard
Toggles
RamToggleᵀᵀLight duty nylon cavity fastener. The nylon body is
non-conductive to electricity.
Spring and Gravity TogglesIdeal for light to medium duty hook and bracket
installation, electrical fittings and bathroom
accessories into wall and ceiling applications.
Fixing to Plasterboard
Timber Connectors
TIMBER CONNECTORS
HANGERS
BRACKETS
BRACING TIE-DOWN CONNECTORS
CONNECTOR PLATES
STRAPS
NAILS & FIXES BUILDERSHARDWARE
BracingTimber Connectors
Strap BraceFor wall and roof bracings. Use with PrydaTensioners.
Strap Brace TensionersAvailable in options for hand fastening and fastening with power tools. Use with PrydaStrapbrace.
SpeedbraceFor wall and roof bracing.
Mini & Maxi BraceFor diagonal wind bracing and nogging of wall frames.
All Pryda bracings are manufactured from G300 Z275 ZincForm® steel or equivalent for high strength and corrosion resistance in normal, interior uses.
Tie Down Connectors Timber Connectors
To install Pryda Minigrips, Multigrips or Triplegrips; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.
MultigripsIdeal connectors for many uses in timber framing, eg., tie-down connectors; carport, pergola and deck construction; right angle joints. Available in Galvanised and G316 Stainless Steel.
TriplegripsCan be used for a variety of nail fixed timber joints, eg., roof truss to wall plate; rafter or ceiling joist to wall plate; purlin to truss; hanger to ceiling joist; or wall stud to bottom plate.
MinigripsEconomical connector for the numerous lightly loaded joints in houses and other buildings. Available in Galvanised and G316 Stainless Steel.
Timber Connectors
To install Pryda Straps & Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.
Batten StrapsUsed for tying down roof battens to trusses and rafters.
Joist StrapsUsed for tying down timber roof battens or purlins to trusses or rafters.
Cyclone StrapsUsed for tying down purlins to trusses or roof trusses to wall frames in high wind areas.
Tie Down Connectors
Tie Down Connectors Timber Connectors
To install Pryda Stud & Truss Ties; use only 35 x 3.15mm galvanised Pryda Timber Connector Nail.
Stud TiesA quick, neat and effective connector between studs and wall plates.
Truss TiesDesigned to tie down roof trusses or rafters to a timber top plate.
Wall TiesRigid wall ties suitable for connecting masonry to timber. Available in G300-Z600 galvanised steel and 316 Grade Stainless Steel.
Joist Hangers
Framing BracketsFor connecting a timber beam/joist to another beam at right
angles, such as beam to beam connections and roof trusses
to supports. Manufactured using G300 galvanised steel and
G316 Stainless Steel.
I-Joist HangersFor fixing/supporting I-joists to the face of timber beams.
Manufactured using G300 galvanised steel.
Timber Connectors
To install Pryda Joist and I-Joist Hangers; use 35 x 3.15mm galvanised Pryda Timber Connector Nails.
Nails & Fixes Timber Connectors
Shade FixFor fixing woven and knitted shade cloth to timber framing. Features rounded edge to eliminate tearing cloth on sharp edges.
Timber Connector NailsRecommended for fixing Pryda Timber Connectors. Size: 35mm x 3.15mm. Galvanised Finish and Stainless Steel G316. Laboratory testings has shown that clouts are not adequate for this purpose as their heads may pop off under less than design load.
Pryda Fix / Foil FixFor fixing foil insulation and shade cloth to timber frames. Holds material securely and prevents tearing.
Connector Plates Timber Connectors
Connector PlatesQuick and easy connector for timber end to end joints.
Corner PlatesFor right angle joints of timbers in light framing. e.g. gate frames, tops of pergola beams, etc.
Nail-On PlatesNail fix to timber to join beams or any heavy duty timber connection
To install Pryda Connector Plates use only 35 x 3.15mm galvanised Pryda Timber Connector Nails.
Connector Plates Timber Connectors
Strap NailsFor joining of timber frames, etc.
Knuckle Nail PlatesMulti-purpose connector for structural and non-structural timber joining and timber protection use.
MininailFor simple butt joints of timber of small sizes.
Pryda Knuckle Nail Plates, Mininails and Strap Nails are manufactured from G300 Z275 ZincForm® steel or equivalent
Brackets Timber Connectors
Heavy Duty AnglesSuitable for stair or shelf brackets, internal or external corner support. Galvanised steel.
Log Support BracketJoins logs and posts quickly and simply without the necessity of checking out. Galvanised steel.
Pergola AnglesA heavy duty multi-purpose building bracket, mostly used for connecting pergola rafters to support beams. Available in G300 galvanised steel and G316 Stainless Steel.
Fascia SupportsUsed to connect the overhangs of rafters or trusses to fascias or fascia ledgers. Galvanised steel.
To install Pergola Angles & Log Support Brackets use 35 x 3.15mm galvanised Pryda Timber Connector Nails.
Builders hardware Timber Connectors
Ant CapsGalvanised steel Ant Caps are used to protect buildings against subterranean termites.
Termite ShieldsGalvanised steel Termite Shields are used to protect buildings against subterranean termites. Complies with AS3660.1-1995.
Edge PinsConvenient pins for holding formwork etc. at ground level.
Post Anchors
Full StirrupCan be bolted to existing concrete or decking or set into concrete.
Half StirrupIdeally suited to uses where the post is located against a wall or step and can only be bolted from one side. Can be bolted to existing concrete or decking or set into concrete.
Solid StemA Full Stirrup post anchor with a solid, angle stem, suitable for setting into wet concrete. (Available on request)
Post Anchors
Post Anchors
Centre FixGenerally used to “hide” the post anchor. The post is slotted at the bottom and bolted through the post and anchor, leaving only the bolt heads, nuts and washers visible. Can be bolted to existing concrete or decking or set into concrete.
Post Anchors
Fish TailA Centre Fix design post anchor that is designed with an angled stem for setting directly into wet concrete. (Available on request)
Centre PinFor use where the post is not to be visible. Due to the fixing method, it is only suitable for small spans or where no roofing is used.
Post Anchors
Bolt DownThese anchors are used for locating 90mm, 100mm, 115mm and 125mm posts onto existing concrete or decking.
High WindEngineered for high wind application areas, including tropical regions. The U shape base is designed for maximum hold-down in concrete. Used for deck construction, gazebo construction, pergola construction & post supports.
Post Anchors
Impulse Tool Fasteners
Fastener Specifications – Nails NAIL HEAD TYPESD – HEAD
Offers similar performance to roundhead nails but enables fasteners to be collated hard up against each other.
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
DekFastOffers an aesthetic appearance when counter sunk into treated pine, gives the look of a round head nail.
NAIL SHANK TYPESmooth
Smooth shank nails provide excellent holding power in most timber applications
RingRing shank nails provide superior withdrawal resistance in softwood receiving timbers.
Screw/TwistExcellent for hardwood receiving timbers.
NAIL POINT TYPEDiamond
The most common and easiest to drive.
NAIL COLLATION TYPE ProStrip Paper Tape
No collation material is left on the job site.
Fasteners Specifications – Brads
BRAD HEAD SHAPELost Head
Where a hidden fix is required
BRAD SHANK TYPESSmooth – gauges available: 18 Gauge = 1.2mm16 Gauge = 1.6mm14 Gauge = 2.0mm Wire diameter indication
BRAD POINT TYPEBlunt ChiselRequires the greatest driving power. Almost eliminates timber splitting.
BRAD COLLATION TYPEGlue Coating
No collation material is left on the job site
Fastener Specifications – Staples
CROWN TYPESStandard Crown
The industry standard for most applications
Raised CrownThe raised crown is mainly used in wire fastening to timber post e.g trellising in a winery or rural fencing. Crown width 12.7mm
STAPLE SHANK TYPE Smooth – available in:
Medium wire: 18 gauge; 1.2mm
Heavy wire: 16 gauge;1.6mm
STAPLE POINT TYPESBlunt Chisel
Not suitable for clinching applications
Divergent PointLegs travel in opposite directions to increase holding power
STAPLE COLLATION TYPEGlue Coating
Glue coating – No collation material is left on the job site
Coatings & Corrosion
Classes
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occurs.Class 3: For external use in mild industrial and moderate marine applications.Class 4: For external use in moderate and severe marineenvironments (generally from 100m to 300m from the beach front).
Air Tool Fasteners
Fastener Specifications – NailsAir tool
NAIL HEAD TYPESRound
Conventional nail head shape. Best suited to applications requiring higher pull-through resistance
D – HEADOffers similar performance to roundhead nails but enables fasteners to be collated hard up against each other.
T & Finish HeadModerate pull – through resistance. Limited damage to timber surface.
DomeOffer an aesthetically pleasing result. Ideal for decking
NAIL SHANK TYPESSmooth
Smooth shank nails provide excellent holding power in most timber applications. Available in a wide range of lengths and shank diameter.
RingRing shank nails provide superior withdrawal resistance in softwood receiving timbers.
Screw / TwistExcellent for hardwood receiving timbers.
Fastener Specifications – Nails Air Tool
NAIL POINT TYPESDiamond
The most common and easiest drive. The diamond point can, however, contribute to splitting in some applications
Shear PointHelps to reduce the splitting encountered with diamond point fasteners
Blunt ChiselAlmost eliminates timber splitting. Not suitable for clinching applications
ConicalIdeal for penetrating steel. Used on nails in steel framed construction
NAIL COLLATION TYPESCoil Nails: Plastic collated – 15 degree and 0 degree
Genuine no-flag nailing system for cleaner, better looking jobs. Ensures positive delivery of nail every time
Strip Nails: Pro-Strip Paper TapeNo collation material is left on the job site.
Strip Nails: Duo-Fast Round Head Strip NailsThe system enables round head nails to be collated for 20 degree strip nailers.
Strip Nails: T Head NailsTypically these nails are constructed from a band or wire. The nails are covered in a glue to help protect them from separating.
Fastener Specifications – BradsAir tool
BRAD HEAD SHAPELost Head
Where a hidden fix is required
D-HeadTight collation with improved pull through resistance.
BRAD SHANK TYPESSmooth – gauges available: 18 Gauge = 1.2mm16 Gauge = 1.6mm15 Gauge = 1.8mm14 Gauge = 2.0mm Wire diameter indication
BRAD POINT TYPEChiselA common cut style for most brads and staples
BRAD COLLATION TYPEGlue Coating
No collation material is left on the job site. The brads are bound closely together to maximize magazine capacity of the tool
Plastic TapePlastic tape will not deteriorate in rain or moisture. Small amount of waste, only flakes of plastic.
Fastener Specifications– StaplesAir Tool
CROWN TYPESNarrow Crown
Medium Crown
Wide Crown
STAPLE POINT TYPESBlunt Chisel
Not suitable for clinching applications
STAPLE SHANK TYPE Smooth – available in:
Fine wire:23 – 19 gauge; 0.6mm – 1.0mm
Medium wire: 18 gauge; 1.2mm
Heavy wire: 16 gauge & larger; 1.6mm & larger
STAPLE COLLATION TYPEGlue Coating
Glue coating – No collation material is left on the job site. The staples are bound closely together to maximize the magazine capacity of the tool.
Coatings & Corrosion
Classes
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occurs.Class 3: For external use in mild industrial and moderate marine applications.Class 4: For external use in moderate and severe marineenvironments (generally from 100m to 300m from the beach front).
Applications
Framing
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade Pack
RoundConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Duo-Fast Strip Nails
Applications include: • wall frames• roof trusses• floor substructures• eaves framework
Roofing - Tile
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel Packs JDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade Pack
Applications include: • Setting out battens for roof tiling • Place roof battens against proud nails • Fastening Battens for roof tiling
Bracing – Sheet & Metal
Round HeadConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Dome HeadOffer an aesthetically pleasing result.
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Applications include: • Plywood bracing• Braceboard sheet• Strap bracing • Metal roof bracing• Maxi bracing
Flooring – Sheeting
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
Round HeadConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Dome HeadOffer an aesthetically pleasing result.
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Types of sheet flooring include: • Particleboard• Plywood
Metal Connectors & Brackets
Round HeadConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Suitable for connectors and brackets such as: • Triple grips• Multigrips• Minigrips• Wall brackets
• Tie down straps • Joist hangers• Beam hangers • I-Joist / I-Beam hangers• Hanger straps
Plumbing
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade Pack
Applications include: • Fastening noggings for plumbing fittings • Fastening bath frames
Electrical
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade Pack
Applications include: • Blocking for light fittings• Blocking for light switches and power points • Fastening noggins or blocking for supporting ceiling fans
Plastering
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade Pack
Applications include: • Fastening battens when required for plasterboard
Cladding
D – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel Packs
Round DriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade PackImpulse CladFast Handy Pack
Round HeadConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Dome HeadOffer an aesthetically pleasing result.
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Applications include: • Fastening weatherboards• Fastening blue boards
Fix OutApplications include: • Panelling• Dado rails• Staircase trim• Handrails
• Eaves trim• Skirtings• Door jambs• Architraves
• Window trim • Mouldings• Kitchens
ND Series Brads = 14 gauge
DA Series Brads = 15 gauge
C Series Brads = 16 gauge
C1 Series Brads = 18 gauge
Angled Brads = 16 gauge
Decking
DekFast Head – Ring ShankOffers an aesthetic appearance when counter sunk into treated pine, gives the look of a round head nail.
DekFast Impulse Value Pack Dek Fast Handy PackDekFast Trade Packs
Round Head – Ring/ScrewConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Dome Head – Ring/ScrewOffer an aesthetically pleasing result.
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Applications include: • Softwood decks• Hardwood decks
FencingD – HEADOffers similar performance to round head nails but enables fasteners to be collated hard up against each other.
Impulse Nail Fuel PacksJDN Strip Nails
RounDriveNew style of head design allows for tight collation and ensures much greater holding power.
Impulse Trade PackImpulse CladFast Pack
Round HeadConventional nail head shape. Best suited to applications requiring higher pull-through resistance
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Dome HeadOffer an aesthetically pleasing result.
Paslode Coil Nails – 15 degree Duo-Fast Coil Nails – 0 degree
Applications include: • Softwood fencing• Hardwood fencing
Can we help?
Bunnings welcomes the opportunity to quote your next job.Please contact your local Bunnings representative or call 133 062.