Fibernet Copper Solutions Solution.pdf · Fibernet Copper Solution Fibernet Copper Solutions. FIBERNET LTD Tel: +972 -4 -9095555 Fax: ... FCO - _ - _ _ FIBERNET LTD Tel: +972 -4 -9095555

FIBERNET LTD

Tel: +972-4-9095555 Fax: +972-4-9590047 www.fibernet.co.il [email protected]

Hi-Tech Park Yokneam Elite 9 Hakidma St. P.O.B 512, 2069206 Israel

Fibernet Copper Solution

Fibernet

Copper

Solutions

FIBERNET LTD



Hi-

12/24 ports Keystones Patch Panel

Introduction:

12 / 24 ports Keystone patch panel 10” / 19”, 1U height.

Features:

Meets All CAT 6A Connecting Hardware requirements with Fibernet's Keystone:

ISO/IEC 11801:2011 (Ed. 2.2)

IEC 60603-7-51:2010

EN 50173-1:2011

EN 50173-2:2007 including amendment A1:2010

ANSI:TIA-568-C.2, Category 6A

Including all connecting hardware alien crosstalk (PS ANEXT and PS AFEXT) parameters.

Mechanical Characteristics:

RoHS Compliant.

UL Verified.

All Plastic parts Zero Halogen Flame redundant: UL94-V0.

Ordering Guide

Patch Panel 24 ports , 19” P/N: MPAF0095-F

Patch Panel 12 ports , 10” P/N: MPAF0703-F

FIBERNET LTD



48 ports Keystones Patch Panel

Introduction:

48 ports FTP keystone patch panel 19”, 1U height for space-saving solution

Provides various categories for different applications with efficient cabling management

Features:

Meets All CAT 6A Connecting Hardware requirements with Fibernet's Keystone:

ISO/IEC 11801:2011 (Ed. 2.2)

IEC 60603-7-51:2010

EN 50173-1:2011



UL 1863 Safety Listed

Printed port numbers

Grounding screw attached on back panel for FTP type



RoHS Compliant.

UL Verified.


Ordering Guide

Patch Panel 48 ports , 19” P/N: MPAF0069

FIBERNET LTD



Fibernet Tool-Less FTP Keystone Jack

Features:

Meets All CAT 6A Connecting Hardware requirements:

ISO/IEC 11801:2011 (Ed. 2.2)

IEC 60603-7-51:2010

EN 50173-1:2011




Tool-Less – No special tools required.


RoHS Compliant.

UL Verified.


IDC Contacts: 22 - 26AWG

Durability: ≥750 Cycles minimum.

Retention: 50N for 60±5 Sec.

Environment Conditions:

Operating Temperature: -10°C - +60°C.

Storage Temperature: -40°C - +70°C.

Operational Relative Humidity: Maximum Non-condensing 93%

Materials:

FIBERNET LTD



Housing: Zinc Alloy Fully Shielded.

All plastic parts: Halogen Free Flame Redundant: UL94-V0.

Spring Wire: Phosphor Bronze Alloy Plated with 50 micro-inch of Gold over 70~100 Micro

inch of Nickel.

IDC: Phosphor Bronze Alloy with 100 Micro-inch 100% Sn Alloy.

Electrical Characteristics:

Insulation Resistance: 500MΩ Min @ 100VDC.

Voltage Strength: 1000 VDC or VAC Peak Contact to Contact 60Hz for 1 Minute.

Voltage Strength: 1500VDC of VAC Peak Contact to Panel 60HZ for 1 Minute.

Spring Wire Resistance ≤ 20mΩ.

IDC Contact Resistance ≤ 2.5mΩ

Ordering Information

Single Door P/N: CRF0374-F

Double Door P/N: CRF0374-D-F

FIBERNET LTD



FIBERNET LTD



Fibernet Cat. 6A S/FTP Patch Cords

Features:

Meets All CAT 6A Patch Cord requirements:

ISO/IEC 11801:2011 (Ed. 2.2)

EN 50173-1:2011


ANSI:TIA-568-C.2:2009

IEC 61935-2:2010 (Ed. 3.0) (Transmission Requirements)

Application:

10GBASE-T Ethernet

1000BASE-TX Fast Ethernet

1000BASE-T Gigabit Ethernet

100BASE-TX Fast Ethernet

10BASE-T Ethernet




Operational Relative Humidity: Maximum Non-condensing 93%

FIBERNET LTD




Insulation Resistance: 500MΩ Min @ 100VDC.

Voltage Strength: 1000 VDC or VAC Peak Contact to Contact 60Hz for 1 Minute.

Mechanical Features:

RoHS Compliant.

UL Verified.

S/FTP Cable Specification:

Composed of 4 twisted pair 26 AWG stranded copper conductors with HFFR jackets.

Copper construction: 7/0.16mm – 26AWG

4 twisted pair wires.

Aluminum polyester foil on each pair

Overall braided shield.

HFFR (LSZH) jacket.

Outer Diameter:6.2±0.2mm

Tensile Strength: ≥ 1.05.

Conductor Resistance: ≤142Ω/Km

Dielectric Strength: 500VAC/1 Min

FTP Plug features:

Insulation Resistance: 500MΩ Min @ 100VDC

Voltage Strength : 1000 VDC or VAC Peak Contact to Contact 60Hz for 1 Minute

Contact Resistance: ≤ 20mΩ

Current Rating @ 35°C ≥1.5A

Housing Material Polycarbonate UL94-V0

Contact Material: Phosphor Bronze Alloy Plated with 50 micro-inch of Gold over 70~100

Micro inch of Nickel.

Shield Material: Brass Alloy Plated with 50 micro-inch of Nickel

Durability: ≥750 Cycles minimum.

FIBERNET LTD



Fibernet Cat. 6A S/FTP Patch Cords Ordering Information

Examples:

FC6A-S-8-03 Patch cord RJ45 CAT 6A S/FTP Gray 3 Meters

FC6A-S-8-075-D-P Patch cord RJ45 CAT 6A S/FTP Gray 7.5 Meters, Fibernet Production, Direct

FC6A-S-8-125-C-P Patch cord RJ45 CAT 6A S/FTP Gray 12.5 Meters, Fibernet Production, Cross

• Patch-cords with Gray color will be supplied with gray Color Boot • Patch-cords with other color will be supplied with transparent Boot • For special request of colored Boots, Please specify in order.

FC6A - S - _ - _ _ _ - _ - _

Cable Length – Meter Digits

dIGITs Standard Lengths:

01 – 1m 02 – 2m 03 – 3m

05 – 5m 10 – 10m

Non-Standard Lengths:

01 to 30 – Any Two digits

01 to 09 must include 0

Color (Standard Color - Gray)

0 – Purple 1 – Black

2 – White 3 – Red

4 – Blue 5 – Yellow

6 – Green 7 – Orange

8 – Gray – Standard Color

Cable Length – 0.1 Meter Digit

1 to 9 – for 10cm (0.1m) increments (usually 5 or None)

None – 0 (Standard)

Production

P – Produced at Fibernet

None – Equivalent import


Polarity

C – Cross

D – Direct

FIBERNET LTD



FIBERNET LTD



Fibernet Cat. 5e F/UTP Patch Cords

Features:

Meets All CAT.5e Patch Cord requirements:

ISO/IEC 11801:2011 (Ed. 2.2)

ISO/IEC 61156-6 (Ed.2)

ANSI:TIA-568-B.2





Frequency Range: 1-100 MHz

Impedance: 100 Ω

Mechanical Features:

RoHS Compliant

UL Verified (VW-1)

F/UTP Cable Specification:

Composed of 4 twisted pairs, 26 AWG stranded copper wires + FR-LSZH jackets

4 twisted pair stranded copper wires with + drain wire

Copper Construction: Stranded 7 x 0.16 mm – 26 AWG

Drain wire: Stranded 26 AWG

Insulation Material: PO

Overall Cable Shield Material: Aluminum/polyester foil

Overall Cable Shield Design: 100% Coverage

FR-LSZH (HFFR) jacket

Outer Diameter: 5.7 mm

Conductor Resistance: ≤145Ω/Km

Dielectric Strength: 500VAC/1 Min

FIBERNET LTD



Fibernet Cat. 5E F/UTP Patch Cords Ordering Information

Examples:

FC5E-FU-8-03 Patch cord RJ45 CAT.5E F/UTP Gray 3 Meters

FC5E-FU-8-075-D-P Patch cord RJ45 CAT.5E F/UTP Gray 7.5 Meters, Fibernet Production, Direct

FC5E-FU-8-125-C-P Patch cord RJ45 CAT.5E F/UTP Gray 12.5 Meters, Fibernet Production, Cross

Patch-cords with Gray color will be supplied with gray color Boot

Patch-cords with other color will be supplied with transparent Boot

For special request of colored Boots, Please specify in order.

Cable Length – Meter Digits

dIGITs Standard Lengths:

01 – 1m 02 – 2m 03 – 3m

05 – 5m 10 – 10m

Non-Standard Lengths:

01 to 30 – Any Two digits

01 to 09 must include 0

Color (Standard Color - Gray)

0 – Purple 1 – Black

2 – White 3 – Red

4 – Blue 5 – Yellow

6 – Green 7 – Orange

8 – Gray (Default)

Cable Length – 0.1 Meter Digit

1 to 9 – for 10cm (0.1m) increments (usually 5 or None)

None – 0 (Standard)

Production

P – Produced at Fibernet


FC5E - FU - _ - _ _ _ - _ - _

Polarity

C – Cross

D – Direct

FIBERNET LTD



Fibernet Copper Outlets

Introduction:

Fibernet Cat6a Outlets are designed for a comfortable installation. This is ensured by a strain relief

providing an easy cable positioning and cable fixture to the outlet housing. The outlets have a slim

design and excellent performance. The modular construction allows flush mounting or wall

mounting installation using a universal back box.

Features:

Compatible with Fibernet Tool-Less FTP Keystone Jack.

Material: FR according to UL94V-0




Max. Humidity Operation: 93%

Outlets Construction

Single port angled Outlet: 80x80mm faceplate

FIBERNET LTD



Double port angled Outlet: 80x80mm faceplate

Back Box for wall installation: (compatible with all 80x80mm faceplate)

Gewiis adapter for Fibernet Tool-Less FTP Keystone Jack

FIBERNET LTD



Ordering Guide:

Outlet Type:

S -Single port angled Outlet: 80x80mm:

D -Double port angled Outlet: 80x80mm:

G -Gewiis adapter for

Back Box for Wall Installation:

1 – Included

2 - None

Fibernet Tool-Less FTP Keystone Jack

1 – Included

2 - None

FCO - _ - _ _

FIBERNET LTD



Fibernet Copper Connection Box

Introduction:

Connection boxes serve as a consolidation point providing flexible cabling arrangement in

the field. See below for specification and performance levels of this product line.

Performance

UTP Termination Connection Box FTP Termination Connection Box UL/cULus 1863 LISTED

ANSI/TIA-568-C.2, ISO/IEC 11801 for CAT 5e ANSI/TIA-568-C.2, ISO/IEC 11801 for CAT 6

Connection Box Construction

Small size: 68.9x40.8 mm Cat 6 Connection box – Metalized cover.

Ordering Guide:

Cat5e Connection Box P/N: FCCB-5E Cat6 FTP Metalized Connection Box P/N: FCCB-6F

FIBERNET LTD



Fibernet 19” Cable Management Panel

Introduction:

Cable management Panel available in 2 sizes, Lightweight plastic construction provides durability and easy installation. Provide a universal solution for manage all kind of cables

on a 19” rack.

Features:

Rounded edges on fingers protect cables from snags and damage to cable. Flexible fingers allow easy installation and removal of cables. Increased finger spacing provides larger area for high performance Cat6 cables

Pass-through holes allow front to rear cabling (Back to Back) Mount to standard 19” EIA racks and cabinets

Ordering Guide:

1U Cable Management Panel P/N: MP3556

2U Cable Management Panel P/N: MP3556-2U

Documents

Fibernet Copper Solutions Solution.pdf · Fibernet Copper Solution Fibernet Copper Solutions. FIBERNET LTD Tel: +972 -4 -9095555 Fax: ... FCO - _ - _ _ FIBERNET LTD Tel: +972 -4 -9095555