Fagor F1810 WFK1018 Washer SM Angl

8/18/2019 Fagor F1810 WFK1018 Washer SM Angl

1/22

TECHNICAL

SERVICE

ASSISTANCE

RANGE:

PRODUCT:

TECHNICAL STUDY

t e c h n i c a l

Washing machines 2007

Fagor Innovation 8 kg. (V1)

Date: 25/02/2008

Document No.: 14538


2/22

How to use this manual

This document is intended for all persons rendering technical support services (T.S.S.).

It is designed to facilitate the repair of the product described. It provides documentary

support for technical consultations.

This manual contains notes warning about safety issues:

t e c h n i c a l

© Copyright by Fagor Electrodomésticos S.Coop. 2008. All rights reserved. The total

or partial reproduction of this document, by any procedure and on any type of media,

is prohibited without written authorisation from the holder of the usage rights. Breach

of this copyright will be pursued in conformity with applicable legislation and may lead

to criminal charges.

FAGOR ELECTRODOMESTICOS reserves the right to introduce, without priornotication, any modications to the characteristics of its manufactured products.

I

Electrical hazard: This identifies potential risks for theappliance. Such risks may cause permanent damage to

the appliance.

Important: This identifies information that is critical fora correct understanding of the product.

!Warning: This identifies information or circumstancesthat may cause personal injuries or death.


3/22

Table of contents

t e c h n i c a l

1.- Warnings and precautions ...................................1

2.- Features .................................................................3

3.- Description of operation .......................................7

3.1.- General description ............................................................. 7

3.1.1.- Component characteristics ........................................................ 7

3.1.2.- Conguration of the V1 circuits ............................................... 10

3.1.3.- T.S.S. Programme ...................................................................11

3.1.4.- Washing machine vibrations .................................................... 13

3.1.5.- Spin attempts .......................................................................... 16

3.2.- Drawings and diagrams .................................................... 17


4/22

Warnings and precautions

t e c h n i c a l

1

1.- Warnings and precautions

!The washing machine must be connected to an earth.

If this basic safety rule is not respected, the manufacturer shall under no circumstances

accept liability for injuries suffered by persons, or for damage to objects.

In order to avoid re risk, electric shock, personal injury or other injuries when

using the washing machine, take the following precautions:

This washing machine is supplied with a manual that contains instructions on

operation, maintenance and installation. Read all the instructions before using thewashing machine.

Do not wash articles which have been previously cleaned, washed, soaked or treated

with gasoline, dry-cleaning solvents or other inammable or explosive substances as

they produce vapours that may ignite or explode.

Do not add gasoline, dry-cleaning solvents or other inammable or explosive substances

to the wash water since they produce vapours which may ignite or explode.

Do not repair or replace any part of the washer, nor attempt any type of service unless

it has been recommended in the manual’s maintenance instructions..

Do not stand or sit on the machine, or lean on the open loading door.

To reduce the risk of re or electric shock, do NOT use an extension lead or adapter

to connect the washing machine to the mains electricity.

The machine must only be used for what it was designed.

Follow the washing instructions recommended by the manufacturer of the item to

be washed.

Do not start the washing machine until you have made sure that:

• It has been installed according to the installation instructions.

• All of the water connections, drainage, electricity and earthing comply with

local regulations and/or other applicable regulations.


5/22

Warnings and precautions

t e c h n i c a l

2

Specications plate (Registration plate)

This is situated on the hatch on the front of the washing machine. This plate indicates

the following:

FAGOR F-1810

COD.905014763

0905014763080200001

2200W 220-230V-50Hz

10A. 4.9-98N/cm2

NIF ESF20020517

N.080200001

TYPWM-900E3B

Mains voltage and frequency

Month of manufacture

Year of manufacture

Washing machine

code (9 digits)

Total power

REGISTRATION PLATE

MAKE AND MODEL

WASHING MACHINE CODE SERIAL NUMBER

POWER, VOLTAGE AND FREQUENCY

MAINS WATER PRESSURE

BARCODE

TYPE OF APPLIANCE

CAPACITY

OFFICIAL APPROVAL SYMBOLS AND OTHERS


6/22

Features

t e c h n i c a l

3

+

AA

A d v a n c e d B a l a n c e S y s t e m

kg

10 0 0 rpm

8

400

700

1000

3h 6h 9h

Stop

Select

2.- Features

This range comprises of the following models:

Button

ON/OFF

Drawer for

detergent

Programme

selector

Start/pause

button

Spin + flot

buttonTime delay

button

Additional

functions

button

Wash programmes

For washing machines manufactured after 1st of May 2007

PROGRAMMES V1 circuits

NORMAL DELICATE FABRICS SPECIAL

1 Normal cold 7 Delicate Mixed 40ºC 10 Antibacterial 90ºC

2 Fast 30ºC 8 Delicate cold 11 Eiderdown 30ºC

3 Normal 30ºC 9 Delicate 30ºC 12 Curtains 30ºC

4 Normal 40ºC 13 Hand wash

5 Normal 60ºC 14 Quick (15 minutes)

6 Pre-wash 60ºC 15 Rinses

16 Spin

LB6W302A1 Circuit


7/22

Description of operation

t e c h n i c a l

4

Spin

The wash options must always be selected after selecting the wash programme. Any change to the programme carried out during

the selection cancels the options which were

previously selected.

a) Spin selection button. The selected programme

has an associated spin speed in revolutions per

minute, and the corresponding spin speed pilot light

turns on.

b) To change the speed, press the spin button

repeatedly, and the appropriate pilot light willlight up.

c) Skip spin option. Press the spin button once

more to reach the skip spin option. This programme

is used to prevent creases from forming in special

fabrics, as it has no nal spin.

Time delay option

Time delay selection button

A delay of up to 9 hours may be selected. The

delay must be selected after choosing the wash

programme. To select the time delay in hours,

choose 3, 6 or 9 hours.

Cancel time delay

To cancel the delay, press the time delay button until the pilots indicating the delay

go off. Changing to another programme also cancels the delay.

Start

Start/Pause button

a) To start the washing machine you must press the

start/stop key.

400

700

1000

3h 6h 9h

Stop

Select

400

700

1000

3h 6h 9h

Stop

Select

400

700

1000

3h 6h 9h

Stop

Select

400

700

1000

3h 6h 9h

Stop

Select

l

a


8/22


t e c h n i c a l

5

Additional functions

Button for selecting additional functions according to programmes.

There are 2 options: anti-crease and intensive wash.

Press the button to display the required option.

By pressing several times, you can choose

between various combinations of one or two

additional functions at the same time, depending

on the chosen programme.

Key: Anti-crease

This stops at the nal rinse, leaving the clothing oating in water. When the function is

deactivated, the washer continues the programme, draining and spinning.

This is used when you are not at home, for example, to delay the spin until you have

arrived so that creases are not caused by the clothes being spun and then left in

the drum.

Key: Intensive Wash

This option, specially recommended for very dirty or stained garments, gives better

results by lengthening the wash cycle.

Programme progress

When the programme is running, the pilot lights indicate the current programme phase.

Any option button may be selected, as long as the

wash phase in which it takes effect has not passed,

and when the programme permits that option.

Pressing the delay button during the wash has no

effect on the washer.

Pressing the Start/Pause button during the washputs the washer in the PAUSE state.

Important: If, during the wash cycle, the programme is changed using the selector,

the washer is left in the PAUSE state, and the programme is canceled. To add or

remove an article, press the start/pause button and make sure that the water is not

above the door overow level, and that the interior temperature is not high. Press the

start/pause button again to re-start the washer from the same phase of the cycle in

which it was stopped.

400

700

1000

3h 6h 9h

Stop

Select

400

700

1000

3h 6h 9h

Stop

Select


9/22


t e c h n i c a l

6

Power failure

When the supply returns after a power failure, the washer continues to work as normal,

from the point at which it stopped (its memory lasts a few hours).The same thing happens if the ON/OFF button is pressed.

Warnings

To reduce the noise level of the spin cycle: use the adjustable feet to level the washer.

Aim to wash clothes of different sizes in the same wash programme, for a better

weight distribution in the drum when spinning.

All the models have a spin cycle safety system, which prevents them spinning if thedistribution of the clothes in the drum is very uneven. This prevents excessive vibration.

If at any time the clothes have not been correctly spun, spread them out more evenly

in the drum, and spin again.


10/22


t e c h n i c a l

7

3.- Description of operation

3.1.- General description

3.1.1.- Component characteristics

Component Function Features

Motor

1250 RPM

Used in machines

with variable spin,

and makes rotating

movements when

washing and spinning.

Motor power supply:

- Clockwise, power

220 V., contacts 2and 3. Bridge between

contacts 5 and 6.

- Anti-clockwise, power

220 V. , contacts 3

and 5. Bridge between

contacts 2 and 6.

Voltage: 220 v / 50 Hz

Stator resistance: 1.3 Ω

Rotor resistance: 1.7 Ω

Tachogenerator resistance:

184 Ω

Tachogenerator voltage:

1.2 v / 1,000 rpm

Double field motor

1400 RPM

Used in machines

with variable spin,

and makes rotatingmovements when

washing and spinning.

Motor power supply:

- Clockwise, power

220 V, contacts 4


contacts 3 and 6.

- Anti-clockwise, power

220 V, contacts 4


contacts 5 and 3.


Stator resistance: 3.3 Ω

Rotor resistance: 2.46 ΩTachogenerator resistance:

90 Ω

Door lock Opens hatch lock. Voltage: 220 v / 50 Hz

16 Amp.

Delay of between 40 and

75 seconds.


11/22


t e c h n i c a l

8


Door lock with

instant opening

Hatch closing

Manual opening for use

in case of electricity

supply failure

Recirculation pump Recirculates the water

in the drum for greater

wash effectiveness

and reducedprogramme times

Voltage: 220-240 v / 50 Hz

Drainage pump resistance

170 Ω

Recirculation pumpresistance 180 Ω

Both have a thermal

protector

Power 30 W

Double connectorised

electrovalve

Allows water intake in

the pre-wash, wash and

rinse phases

EV1 pre-wash orange

connector

EV2 wash blackconnector

EV1 + EV2 additive

intake

Voltage: 220-240 V /50 Hz

Power: 5 W

Flow: 6.7 litres / minute

Pressure: 0.5-10 kg / cm²

Resistance: R1=R2=R3=

3.7K Ω3/4 Thread Gas

12mm conduit diameter

Pressure switch The pressure gauge

is activated in the

following conditions:- When the wash level

reaches 12 litres. (11-12)

- When the level

exceeds 33 litres

(overflow), the drainage

pump is activated

(safety). (11-16)

- The rinse level is

performed according

to the time of the

microprocessor of theelectronic card.

Level 1

102 / 72 ± 3

Overflow safety device

310 ± 10

11

12

14

16

12 Water inlet14 Heating16 Overflow

11 Common


12/22


t e c h n i c a l

9


Heating resistance Heating element

+ thermofuse

incorporated into the

element itself

Thermofuse cut-out

temperature165ºC

Resistance: 26.4 Ω

Material: Austenitic

stainless steel

Power: 2022 W

Voltage: 230 v

NTC ≤ 30ºC variable

resistance value 9786 Ω

V1 electronic circuit Power and display

circuit


Important: It is necessary

to configure the circuit

before starting the machine.

(follow configurationinstructions)


13/22


t e c h n i c a l

10

3.1.2.- Conguration of the V1circuits

1. ON/OFF switch turned off.

2. Press the Start/Pause button and keep it pressed.

3. Press ON/OFF button until the STOP LED lights up.

4. While still holding down the Start/Pause button, press the spin button until the

Wash, Rinse, and STOP LEDS light up. Then immediately release the Start/Pause

button and spin buttons at the same time.

5. Press the spin button once, and the circuit conguration LEDS will light up (must

match the sticker attached to the body of the tray).

6. To change the conguration of:

* Speed: press the speed button until the LED or LEDs match the sticker.

* Cold water: Press the time delay button. The LED must be off.

* RH: press the Select button until the Flot and Intensive LEDS light up.

7. To conrm the conguration, press the Start/Pause button until the Skip Spin Option,

Time Delay and Select LEDs start to ash.

+

AA


kg

10 0 0 rpm

8

400

700

1000

3h 6h 9h

Stop

Select

C O N T R

O L P A N E L B A R C O D E

R E F E R E N C E


14/22


t e c h n i c a l

11

3.1.3- T.S.S. Programme

1. ON/OFF switch turned off.

2. Press the Start/Pause key and keep it pressed.

3. Press ON/OFF switch until the STOP LED lights up.

4. While still holding down the Start/Pause button, press the spin button until the

Wash, Rinse, and STOP LEDs are lit up. Then immediately release the Start/Pause

button and spin buttons at the same time.

5. Press the spin button once, and the circuit conguration LEDs will light up (must

match the sticker attached to the body of the tray).

6. To conrm the conguration, press the Start/Pause button until the Skip Spin Option,

Time Delay and Select LEDs start to ash.

The circuit then carries out the T.S.S. programme and the wash LED lights up.

LED SELECTION MODE TIME (APPROX.)

WASH Water intake via Pre-wash Electrically-operated valve +

Movement of wash motor at 55 rpm

10 sec.

RINSES Emptying + Spin 5 min.

STOP Water inlet via the electrically operated valve for Washing

until wash level is reached

Pressure switch

level

EXTRA

RINSE

The element starts to heat up until it reaches 40ºC +

Intermittent recirculation - 90 sec. not activated and 30 sec.

activated

40ºC

INTENSIVE Water input via pre-wash, wash and softener electrically-

operated valves + Recirculation

5 sec.

Drainage Pump 30 sec.

+

AA


kg

10 0 0 rpm

8

400

700

1000

3h 6h 9h

Stop

Select


15/22


16/22


t e c h n i c a l

13

3.1.4.- Washing machine vibrations

• Wash vibrations

V E

R Y D E L I C A T E S P I N

S E M I - D E L I C A T E S P I N

D E L I C A T E S P I N

S U P E R S P I N

S P I N P L U S

T . S . S .

S P I N

F L O T S P I N ( m a x i m u m t i m e 2 h o u r s )

N O R M A L S P I N

E X T R A S P I N

S E C .

S E C .

S E C .

S E C .

S E C .

S E C .

S E C .

S E C .

S E C

.

N O N - D

E T E C T I O N

O F O V E R F L O W

A R E A

A N T I - C L O C K W I S E

C L O C K W I S E


17/22


t e c h n i c a l

14

• Spin vibrations

Easy iron

N O R M A L S P I N A N D E A S Y I R O N / W A S H I N G

M A C H I N E S E 2 0 0 2

E A S Y I R O N P H A S E 1



I M B A L A N C E T E S T

I M B A L A N C E T E S T

I M B A L A N C E T E S T 1

a n d 2

I M B A L A N C E T E S T 1 a n d 2

M A C H I N E M O D E L

R P M

s e l e c t o r



18/22


t e c h n i c a l

15

Normal spin:

N O R M A L S P I N

P H A S

E 0

M A C H I N E M O D E L

S t e p

7

S t e p

6

S t e p

5

S t e p

4

S t e p

3

S t e p

2

S t e p

1

S t e p

0

I M B A L A N C E T E S T 1

, 2

, 3

A c c o r d

i n g

t o p r o g r a m m e

S E C

. R P M

S e

l e c

t o r S

e t t i n g s


19/22


t e c h n i c a l

16

3.1.5.- Spin attempts

If the washing machine detects the unequal balance of clothes in the spin cycle it will

follow this process:

The total number of attempts to start spinning is 20, divided according to these criteria.

In the rst 6 attempts, the maximum unbalanced limit allowed is 550 g.

Between the 7th and 18th attempts the maximum unbalanced limit allowed is 800 g

and the nal speed is less than the nominal speed, for example a washing machine

of 1,200 rpm will spin at 1,000 rpm.

For the 19th and 20th attempts, the maximum unbalanced limit allowed is 1,500 g,

and the nal spin speed will be 650 rpm, except in washing machines with a nominal

speed of 700 rpm, which will spin at 400 rpm.

These attempts to reposition the clothes in the drum will increase the total programme

time by 20 minutes.

The LCD screen will display CO3. This is not considered a fault, it merely warns the

user about the security measure the circuit has detected.

If an imbalance is detected in the rinse phase the number of attempts will not exceed 3.

In 8 kg washers dating from after 01/11/2007, the number of imbalance correction

attempts is reduced by half (9 attempts).


20/22


t e c h n i c a l

17

3.2.- Drawings and diagrams


21/22


t e c h n i c a l

18

DOOR LOCK

R E C I R C U L A T I O N

P U M P

D R A I N

P U M P

E . V . 3

H O T W A T E R

E . V . 1

P R E - W A S H

E . V . 2

W A S H

F I L T E R

PRESSURE SWITCH

RESISTANCE

FUSE

MOTOR

AMA–GREEN

AMA–GREEN

Documents

Fagor F1810 WFK1018 Washer SM Angl