Upload
others
View
20
Download
0
Embed Size (px)
Citation preview
���������� ��������������������� ��������������������� ��������������������� �����������
MINELAB F1A4OPERATOR TRAINING
���������� ��������������������� ��������������������� ��������������������� �����������
Course Outline• LESSON 1: Description of the F1A4
• LESSON 2: Assembly of the F1A4
• LESSON 3: Principle of Operation
• LESSON 4: Operation of the F1A4
• LESSON 5: Operator Maintenance and Care
• Outdoor Training Operator Evaluation
���������� ��������������������� ��������������������� ��������������������� �����������
LESSON 1Description of the F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
• Packed length – 71cm• Operating length – 120 - 145cm• Weights
• Shaft mounted – 3.0 kg• Hip mounted – 1.5 kg• Packed – 4.0 kg
• Water Resistance – IP65• Battery life:
• D Cell Alk Batteries – 16 hours• D Cell NiCd (4500mAH)-10 hours
Specifications
���������� ��������������������� ��������������������� ��������������������� �����������
Carry Bag
OPERATIONS MANUAL F1A4
BAG CONTROL BOX
TEST PIECE MINE DETECTOR
BAG COMPACT
EARSET
CONTROL BOX
ARMREST
'D' CELL BATTERIES (4)
P0141-C
FIELD GUIDE F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
Main Components
• Armrest• Upper Shaft• Handle• Lower Shaft
���������� ��������������������� ��������������������� ��������������������� �����������
Main ComponentsMonoloop Coil, Cable and Windings
Note: Picture of a training coil showing internal coil details – coil bottom and shielding removed.
���������� ��������������������� ��������������������� ��������������������� �����������
Main Components
• Skid Plate• Ear Sets• Batteries• Test Piece
���������� ��������������������� ��������������������� ��������������������� �����������
F1A4 Control Box
�������
Battery
Low
AudioReset
NoiseCancel
Coil
Off
On BalanceSearch ����
���������� ��������������������� ��������������������� ��������������������� �����������
Stowing the Detector
OPERATIONS MANUAL F1A4
BAG CONTROL BOX
TEST PIECE MINE DETECTOR
BAG COMPACT
EARSET
CONTROL BOX
ARMREST
'D' CELL BATTERIES (4)
P0141-C
FIELD GUIDE F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
Questions?
���������� ��������������������� ��������������������� ��������������������� �����������
LESSON 2Assembly of the F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
Shaft Assembly
• Secure the Handle• Orient Shafts• Unlock Lower
Camlock• Confirm Cable in
Guide• Connect Shafts• Lock Lower Camlock
���������� ��������������������� ��������������������� ��������������������� �����������
Control Box - Shaft Mount
• Secure Grommet
• Unlock Upper Camlock
• Insert Armrest• Lock Upper
Camlock
���������� ��������������������� ��������������������� ��������������������� �����������
• Secure Grommet
• Unlock Upper Camlock
• Insert Armrest
• Lock Upper Camlock
Control Box - Hip Mount
���������� ��������������������� ��������������������� ��������������������� �����������
Battery Installation
• Place the Control Box upside down in Compact Bag
• Confirm the Battery Map• Place two centre batteries
into Battery Carrier first• No need to remove Battery
Carrier from Control Box• Do not force Locking Clips
Control BoxSnaplocks
Battery CoverSnaplocks
Battery Cover
���������� ��������������������� ��������������������� ��������������������� �����������
Control Box Connection
���������� ��������������������� ��������������������� ��������������������� �����������
Coil and Earset Connection
Coil Connector
Earset Connector
���������� ��������������������� ��������������������� ��������������������� �����������
Disassembly
OPERATIONS MANUAL F1A4
BAG CONTROL BOX
TEST PIECE MINE DETECTOR
BAG COMPACT
EARSET
CONTROL BOX
ARMREST
'D' CELL BATTERIES (4)
P0141-C
FIELD GUIDE F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
Questions?
���������� ��������������������� ��������������������� ��������������������� �����������
LESSON 3Principle of Operation
���������� ��������������������� ��������������������� ��������������������� �����������
Principle of Operation
Landmine Landmine
���������� ��������������������� ��������������������� ��������������������� �����������
Landmine Landmine
Principle of Operation
���������� ��������������������� ��������������������� ��������������������� �����������
Multi Period Sensing
���������� ��������������������� ��������������������� ��������������������� �����������
Decay curves from the same size target are independent of pulse width
Multi Period Sensing
���������� ��������������������� ��������������������� ��������������������� �����������
Decay curves from the same size target are independent of pulse width
Decay curves from ground response depend upon the width of the pulse
Multi Period Sensing
���������� ��������������������� ��������������������� ��������������������� �����������
Decay curves from ground responsedepend upon the width of the pulse
Decay curves from the same size target are independent of pulse width
Multi Period Sensing
���������� ��������������������� ��������������������� ��������������������� �����������
Ground Balance
���������� ��������������������� ��������������������� ��������������������� �����������
Questions?
���������� ��������������������� ��������������������� ��������������������� �����������
LESSON 4Operation of the F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
Control Box Operation
�������
Battery
Low
AudioReset
NoiseCancel
Coil
Off
On BalanceSearch ����
• On/Off Switch• Ground Balance• Noise Cancel• Audio Reset• Battery Low• Coil Connector• Earset Connector
���������� ��������������������� ��������������������� ��������������������� �����������
�����
��
������ ������
6 seconds
� "Beeeep"
"Beeeep"
"Beeeep"
Normal Procedures
���������� ��������������������� ��������������������� ��������������������� �����������
NoiseCancel 70 seconds
"Beep Beep Beep Beep" "EEaw EEawEE"
"Beep"
�
�������
Battery
Low
AudioReset
NoiseCancel
Coil
Off
On BalanceSearch ����
Optional Procedures
���������� ��������������������� ��������������������� ��������������������� �����������
� �
Battery
Low
"BeepBeepBeep"BeepBeepBeep
�������
Battery
Low
AudioReset
NoiseCancel
Coil
Off
On BalanceSearch ����
Critical Safety Procedure
���������� ��������������������� ��������������������� ��������������������� �����������
Pinpointing TargetsSweeping
P0022-A
���������� ��������������������� ��������������������� ��������������������� �����������
Pinpointing TargetsEdge DetectionField of Detection
Search head
Tape
r at d
epth
Full
wid
th a
t dep
th
Field of detec tion
Full width field of detec tion
Ground level
Other detectors F1A4
���������� ��������������������� ��������������������� ��������������������� �����������
F1A4 Pinpointing a Small TargetUsing Edge Detection
PinpointingGeneral Target Location
Pinpointing TargetsEdge Detection
Pinpointing Small Targets
���������� ��������������������� ��������������������� ��������������������� �����������
• Step 1
Pass Coil over target at decreasing heights to gain an indication of centre of target mass
Pinpointing TargetsEdge Detection
Large or Multiple Targets
���������� ��������������������� ��������������������� ��������������������� �����������
• Step 2
Approach centre at normal height until detection tone is heard
Pinpointing TargetsEdge Detection
Large or Multiple Targets
���������� ��������������������� ��������������������� ��������������������� �����������
• Step 3
Repeat Step 2 at small intervals to obtain outline of target
Pinpointing TargetsEdge Detection
Large or Multiple Targets
���������� ��������������������� ��������������������� ��������������������� �����������
• Step 4
Listen for changes in tone pitch. This may indicate multiple targets to include booby traps
Pitch Pitch
Pinpointing TargetsEdge Detection
Large or Multiple Targets
���������� ��������������������� ��������������������� ��������������������� �����������
• Threshold ToneLow volume continuous tone indicating correct operation of detector
• Target ToneAbrupt variation to volume and pitch
Tone Target
Small Target
Large Target
F1A4 Detector Tones
���������� ��������������������� ��������������������� ��������������������� �����������
• Turn on Detector 1• Turn on Detector 2 and press
Noise Cancel - wait for Noise cancel to Finish
• Turn on Detector 3 and press Noise Cancel - wait for Noise cancel to finish
• Continue as required
1
23
Noise
Cancel 70 seconds
"Beep Beep Beep Beep"
"Beep"
Operating Multiple Detectors
���������� ��������������������� ��������������������� ��������������������� �����������
Questions?
���������� ��������������������� ��������������������� ��������������������� �����������
LESSON 5Operator Maintenance and Care
���������� ��������������������� ��������������������� ��������������������� �����������
Care of the F1A4 Detector
• Ensure all connectors clean and dry when not in use• Storage temperatures –55º C to +90º deg C• Control box is water resistant but not water proof• Do not use solvents to clean detector - use a damp cloth
with mild soap or detergent• If brought into contact with corrosive substances, including
salt water, wash away with fresh water before stowing detector
• When not operating the equipment, do not leave detector exposed in intense sunlight for prolonged periods
���������� ��������������������� ��������������������� ��������������������� �����������
• Place Skid Plate flat on ground
• Gently place Coil onto into Skid Plate
• Using light foot pressure press Coil into Skid Plate
Fitting the Skid Plate
���������� ��������������������� ��������������������� ��������������������� �����������
Questions?
���������� ��������������������� ��������������������� ��������������������� �����������
This is to certify that
……………………………………………
is a qualified operator of the
MINELAB F1A4 METAL MINEDETECTOR
MINELAB ELECTRONICS PTY LTD
Signed ……………… Dated………………..