Wing strakes/inlet top(make 1)

Wing strakes/inlet top(make 1)

Cut slot to fit wing spar

Cut slot to fit wing spar

Side fairings for launch pylonSand to an airfoiled shape (make 2)

������������ ���Designed by Steve Shumate

All parts made from 6 mm Depron or BlueCore foam unless otherwise specified

Copyright © 2004 All Rights Reserved

������������ ���Designed by Steve Shumate

All parts made from 6 mm Depron or BlueCore foam unless otherwise specified

Copyright © 2004 All Rights Reserved

Wing strakes/inlet top

Bev

el th

is a

rea

Wing strakes/inlet top

(make 2)

Cut slot to fit stabilator pivot

Wing(make 1)

Cut slot to fit wing spar

Cut hole for accessto radio compartment

Cut slot to fit wing spar

2

0

Scale in inches

Scale in inches

2 4

Inlet diverter/spacer(make 2 from 3 mm

Depron or 1/8" balsa)

OPTIONAL: Internal support

for launch pylon (make 1)Side fairings for launch pylon

Sand to an airfoiled shape (make 2)

OPTIONAL: Launch pylon(make 1 from 1/8" lite-ply)

Inlet diverter/spacer(make 2 from 3 mm

Depron or 1/8" balsa)

OPTIONAL: Internal support

for launch pylon (make 1)

Bev

el th

is a

rea

OP

TIO

NA

L: A

ft en

gine

fairi

ngs

Forward inlet tops(make 2) Stabilators

(make 2)

Mounting hole for stabilator servo(cut to fit servo very tightly)

Motor mount(make 2 and

laminate together)0.75" x 0.75" 1/64" ply doublers each side

(drill 3/16" hole for pivot bearing tubes)

Mounting hole for stabilator servo(cut to fit servo very tightly)

0.75" x 0.75" 1/64" ply doublers each side (drill 3/16" hole for pivot bearing tubes)

2

4

Inboard inlet sides(make 2)

Aft Fuselage Top(make 1)

Inboard inlet sides

Cut to fit motor

OP

TIO

NA

L: A

ft en

gine

fairi

ngs

(mak

e 2)

Forward Fuselage Bottom (make 1)

Forward Fuselage Bottom (make 1)

Nosecone top view template(trace outline on top of nosecone

to assist in carving it to shape)

Aft Fuselage Bottom(make 1)

Cut to fit motor

Top

fwd

fuse

lage

(trim

to fi

t)

Bulkhead F-1

3/8" foam strips (2 layers)

F-2

F-1

Bulkhead F-3(make 1)

Bulkhead F-1(make 1)

Bulkhead F-2(make 1)

Bulkhead F-4(make 1)

F-3F-4

Forward Fuselage Sides(make 2)

Aft Fuselage Sides with Vertical Tails(make 2)

3/8" foam strip

Aft Fuselage Sides with Vertical Tails

Cut to fit servo

Flaperon and rudder control horns(make from 1/32" plywood)

0.75" x 0.75" 1/64" plydoublers on inboard side(drill 3/16" hole for pivot

bearing tubes)

Glue 3/8" x 7" strip of foam here to support fuselage top piece

Flaperon and rudder control horns(make from 1/32" plywood)

Canopy (make 11 and laminate together)

F-23/8" foam strips (2 layers)

Nosecone(make 11 and

laminate together)

Canopy (make 11 and laminate together)

Turtledeck Sides (make 2)

Forward Fuselage Sides

Turtledeck Sides (make 2)

3/8" foam strip

Turtledeck Top(make 1 and trim to fit)

Bev

el th

is a

rea

Exhaust nozzle

Make 2 from 1/4" sq. balsa

Exhaust nozzlesides (make 2mirror image)

Make 2 from 1/4" sq. balsa