EX26S & EX26XS SLIDING TABLES

with stainless steel top

Thank you for choosing an EXAKTOR® Sliding Table. This Sliding Table has been designed to function as a perfect upgrade for most contractor and cabinet-style table saw whose owners expect accuracy with every table saw cut made. This EXAKTOR® Sliding Table provides you with the following benefits; • Stainless Steel tabletop laser cut for absolute accuracy. • Sealed Bearings run on Stainless Steel Guide Rails for smooth table travel. • Steel Frame and Legs have baked-on powder coat paint surface for durability. • Quick Release Bracket for removal and/or attachment of the table to other machines. • Toggle Hold-Down Clamp to hold the work piece down on the table and against the fence. • Two movable Work Stops for making repetitive cuts accurately every time. • Two Telescopic Extensions plus a Stainless Steel Panel Support for larger panels. • Optional Outboard Roller for ease of sliding your work onto the table. Prior to installation of the EXAKTOR® Sliding Table please take the time to read this manual and then familiarize yourself with the parts that are used in the assembly of the sliding table. If you have questions or if you feel there are parts of this manual that need clarification, you are encouraged to let us know.

You can contact EXAKTOR Tools Ltd 326 Watline Avenue 210 South Eighth Street

Mississauga, Ontario L4Z 1X2 Lewiston, New York 14092 Canada USA

Tel: 905-568-4459 Tel: 800-387-9789 Fax: 905-568-4059 info.exaktortools.com

2

TABLE SAW SAFETY

1. To prevent accidents keep safety in mind while you work 2. Use the safety guards installed on powered equipment; they are for your

protection. 3. When working on powered equipment keep fingers away from saw blades and

cutters, 4. Wear safety goggles to prevent injuries from flying wood chips and saw dust. 5. Wear headphones to protect your hearing. 6. Consider installing a dust vacuum to reduce the amount of airborne dust in your

workshop. 7. Don’t wear loose clothing, such as neckties or shirts with loose sleeves, or

jewelry, such as rings, necklaces or bracelets when working on power equipment. 8. Tie back long hair to prevent it from getting caught in powered equipment. 9. Keep work areas clean. Cluttered areas invite accidents. 10. Do not force work though the machine. Tools work better and are safer when

they work at their own speed. 11. Do not overreach. Keep proper footing and balance at all times. 12. Do not reach behind the machine to grab a cutoff piece. If the wood binds behind

against the blade or cutter it will kick back faster than you can let go. 13. Disconnect the machine from electrical power before servicing and changing

accessories, such as blades and cutters. 14. Never leave the machine running unattended – turn the power off. Do not leave

the machine until it comes to a complete stop. 15. Do not operate the machine if you are mentally or physically fatigued. 16. If there is something that you do not understand, do not operate the machine! Ask

for help first.

These safety rules do not cover every situation in a workshop. Consider your conditions when setting up and using your EXAKTOR® Sliding Table.

WARNING: NO PART OF THIS MANUAL MAY BE REPRODUCED IN ANY FORM WITHOUT THE WRITTEN APPROVAL OF EXAKTOR® TOOLS LTD.

© EXAKTOR® Tools Ltd, 2004

Model EX26S & 26XS Sliding Table Installation Guide Rail Assembly Caution! When using ratchets, wrenches and other leveraged tools for tightening screws, nuts and bolts, be careful not to over tighten. NOTE: In these instructions the ‘front’ of the machine always refers to where the operator normally stands. Step 1 Fig. 1 There are two possible ways to install Exaktor’s EX26S & EX26XS Sliding Table for use with a table saw.

1. You can attach the Mounting Plate (#03-A) to the edge of the saw’s left hand extension wing by drilling two holes in the lip of the wing, or

2. by first removing the extension wing and attaching the Mounting Plate to the edge of the saw’s table.

If your work consists of cutting panels with veneer or Melamine finish, it is suggested to minimize vibration in the work piece, that the Mounting Plate be attached as close to the saw blade as possible by removing the saw’s extension wing.

NOTE: If the front end of the Sliding Table’s Guide Rails are positioned to project past the ‘front’ edge of the saw table the guide rails for the saw’s rip fence must be moved to the right or be cut off flush with the edge of the table. Position the Mounting Plate (#3-A) so that it is more or less centered on the saw blade arbor, with its top edge approximately 1/8” below the top surface of the saw’s table. Check the alignment of the boltholes. If the existing holes in the Mounting Plate do not fit the table saw, you can drill the necessary holes in the Mounting Plate, or in the edge of the saw table. Fasten the Mounting Plate to the saw table using the bolts* (see Fig.1) from the previously removed extension wing or other appropriate fasteners to fit the saw table.

ALTERNATIVELY. If the extension wing is to remain attached to the saw table, the Mounting Plate (#03-A) can be installed further back on the extension wing so that the ‘front’ end of the Inner Rail Tube can be located behind the front guide Rail for the saw’s rip fence. You will be required to drill two holes in the lip of the extension wing to install the Mounting Plate. NOTE: When bolted to the machine the Mounting Plate must be at 90° to the table surface of the machine. If the edge of the machine’s table is not square to its top, the Mounting Plate must be shimmed. Step 2 Fig. 1 Use two ¼-28 x ½” Hex Head Bolts (#10) to fasten the Inner Cross Brace Bracket (#16) to the underside of Inner Rail (#1-S).

3

4

Step 3 Fig. 1 Use six ¼-28 x ½” Hex Head Bolts (#10) to fasten the Rail Mounting Bracket (#3-B) to the underside of Inner Rail (#1-S).

Step 4 Fig. 1 Use three ¼-28 x ½” Hex Head Bolts (#10) to fasten each of the Leg Mounts (#6-S) to underside of the Outer Rail (#2-S).

Step 5 Fig. 1 Insert the Legs (#7) into the Leg Mounts (#6-S) and snug the four ¼-20x ⅜” Set Screws (#11) to be tightened later. Attach the two Diagonal Braces (#8-AS & #8-BS) and Rear Braces (#8-CS) between the rail assemblies using 5/16-18x¾” Hex Head Bolts (#12) and Square Nuts (#13). Snug up for tightening later. See Fig. 1 for Brace locations. The Guide Rail Assembly is attached to the table saw by placing the Rail Mounting Bracket’s locating fingers in the corresponding slots in the lower edge of the Mounting Plate. The bracket and plate are locked together using two ¼-20x1” Bolts (#67) threaded through the Mounting Plate, and secured with T-Knobs (#44).

Table Assembly Step 6 Fig. 2A & 2B The stainless steel table is shipped with a protective paper. It is suggested that you do not remove this protection until it is necessary to do so. The following steps a, b, c, d, e, f and g in the tabletop assembly (may) have been completed prior to shipping. . a: The two inboard horizontal Bearings (#60B) are installed under the inboard side of the Bearing Support (#28) using ¼-20x1” Button Head Bolts (#67), Spacers (#61), and Eccentric Adjusters (#62). b: The two vertical Bearings (#60C) are installed on the underside of the Bearing Support (#28) using ¼-20 x 1” Button Head Bolts (#67), Bearing Spacers (#61) and Lock Nuts (#34), c: The Brake Lever (#63), positioned as shown, is installed on the underside of the Bearing Support (#28) between the two Bearings (#60B) using a ¼-20x1” Button Head Bolt (#67), Washer (#31), Wave Washer (#33), Spacer (#61) and the Eccentric Adjuster (#62). d: Six 10-32x½” Flat Head Machine Screws (#15) and NyLock Nuts (#65) are used to attach the assembled Bearing Support (#28) and the Inboard Channel (#66) to the underside of the Table (#20-SS). e: Use two ¼-20x1¼” Socket Head Bolts (#27) to attach the Lower Lip (#21-S) to the underside of the Inboard Channel (#66). Do not over tighten. f: NOTE: Position the lower edge of the End Plates(#71) even with the lower edge of the Table(#20-SS). Use Four ¼-20x½” Button Head Bolts (#4) to attach the End Plates to the outside of both the front and rear edges of the Table. g: A Stand-off (#72) is bolted to the outside of both End Plates using a 5/16-18x½” Hex Head Bolt (#73) inserted from inside the edge of the Table. Tighten all of these bolts.

5

6

7

Step 7 Fig. 2C To attach the Angle Adjustment Rail (#23-S) to the outboard edge of the Bearing Support (#28), place Lock Washers (#38) and Flat Washers (#31) on two ¼-20x ¾” Hex Head Bolts (#29A) and insert them through the elongated holes in the lower lip of the Bearing Support (#28). Thread a T-Nut (#48) 0n each Bolt leaving enough slack to slide the T-Nuts into the T-Slot on the inboard side of the Angle Adjustment Rail.

NOTE: Center the Angle Adjustment Rail on the Table. If necessary, shim between the Angle Adjustment Rail and the Bearing Support. Tighten the two Hex Head Bolts (29A). The top surface of the Angle Adjustment Rail must be in the same plane and be level with the top surface of the Table. Step 8 Fig. 2C Thread a Locking Lever (#36) with a washer (#31) into two Table Mounts (#25)

Step 9 Fig. 2C Use two ¼-20x¾” Button Head Bolts (#30) with Washers (#31) to attach the Table Mount (#25) and End Plates (#71) to the outside of both the front and rear edges of the Table (#20-SS). NOTE: Make sure the lower edge of the End Plates are even with the lower edge of the stainless steel Table. A Standoff (#72) is bolted on the outside of both End Plates using a 5/16-18 x ½” Hex Head Bolt (#73) inserted from inside the edge of the Table.

Fence Stop Assembly Step10 Fig. 2C Thread a Stop (#18) through the Stop Tab (#26) and into the Wing Nut (#35). Put a Wave Washer (#33) on the Standoff (#72) at the front of the Table (#20-SS). Put the Stop Tab on the Standoff and secure with a 5/16 -18 x ½ Hex Head Bolt (#73) and a Washer (#32) so that the flat head of the Stop faces the Table. A Fence Stop assembly is also installed on the Standoff at the rear of the table.

Step 11 Fig. 2A Assemble two Lower Bearings. Each consists of a ¼-20 x 1” Button Head Bolt (#67), two Split Lock Washers (#38), small Bearing (#17), Lower Bearing Bracket (#39), Washer (#31) & Lock Nut (#34).

Step 12 Fig. 2A Using ¼-20x1¼” Button Head bolt (#68), Flat Washer (#31), Bearing Spacer (#61) and NyLock Nut (#34) attach the two Lower Bearing assemblies and the two outboard horizontal Bearings (#60-A) under the outboard side of the Bearing Support (#28).

8

9

Step 13 Fig.1 Use an 8-32x½” Phillips Head Screw (#14) to attach a Rubber Bumper (#9A) at the rear end of the Outer Rail (#02-S).

Step 14 FIG. 2C Attach Wiper Brushes (#70) to the front and rear End Plates (#71) using two 8-32 x ½” Phillips Screws (#14) Step 15 Slide the Table onto the assembled Guide Rails, ensuring that the Lower Table Lip (#21-S) hooks under the Inner Rail Tube (#1-S). The two small lower Bearings (#17) should now be located at the underside of the Outer Rail (#2-S). Step 16 FIG. 1 Use a 8-32x½” Phillips Head Screw (#14) to attach a Rubber Bumper (#9B) at the front end of the Outer Rail (#2-S).

Table Adjustments To eliminate side play between the Table and Guide Rails, adjust both of the inboard horizontal Bearings (#60-B) by holding the Bolt (#67) finger tight and turning the Eccentric Adjuster (#62) to lightly preload the Bearings against the Outer Rail Tube (#2-S). Then tighten the Bolt (#67). Adjust the position of the Lower Bearing assemblies so they just touch the underside of the Outer Rail Tube. Tighten the Bolt (#68). To prevent the Table from moving to easily on the Guide Rails you can add resistance by tightening Bolts (#27) that hold the table Lower Lip (#21-S) against the underside of Inner Rail tube (#1-S). Secure with Lock Nuts (#34). To set the Brake Lever (#63) Hold the Button Head Bolt (#67) finger tight; Turn the Eccentric Adjuster (#62) so that the Brake Lever (#63) presses against

the side of the Outer. Tighten the Bolt. The Brake Lever should lock the Table in position, on the Guide Rails, when it is pulled towards the operator. Step 17 FIG. 2 Adjust the Wiper Brushes (#70) to touch the top surface of the Outer Guide Rail (#2-S).

10

Fence Assembly Step 18 Fig. 3 Assemble two Fence Mounts. Use Locking Lever (#36), Washers (#19 & #31), ¼-20x ¾” Bolt (#29), T-Nut (#48) and the Fence Mount (#43). Slide one of these assemblies into each end of the T-slot in the backside of the Fence (#40-S).

Step 19 Fig. 4 The Toggle Clamp (#57) is screwed into the top surface of the Clamping Bar (#56) and is held in position by its Jam Nut. (The top surface of the Clamping Bar is stamped with a “T.”) The Pivot Post (#59), with the O-ring (#64) in place, is inserted through the Clamping Bar, and is held in place by Locking Lever (#36). A Spindle (#58) with Rubber Tip (#58A) is threaded into the lower end of the Toggle Clamp.

Set the Fence (#40-S) on the Table (#20-SS). At the right hand end of the Fence, align the Fence Mount (#43) with the Table Mount (#25) and drop the Pivot Post (#59 through the aligned holes in the mounts. Snug the Bolt (#29) on the Fence Mount for a close fit. The lower end of the Pivot Post is held secure in the Table Mount by tightening the Locking Lever (#36).

Step 20 Fig. 3 With Retainer (#75) in place insert the Carriage Bolt (#45) through the Locking Tube (#47), which in turn, is inserted through the Fence Mount (#43). Swing the Fence and slide the Retainer and head of the Carriage Bolt into the T-Slot on the top of the Angle Adjustment Rail (#23-S). Snug up with the T-Locking Knob (#44).

NOTE: To prevent damage to the top of the Angle Adjustment Rail (#23-S), the lower end of the Locking Tube (#47) should be made flush with the lower edge of the Fence Mount (#43) and held there by tightening the Hex Head Bolt (#29).

11

12

13

To Adjust Table Tracking When fully assembled the sliding table must be level with the machine’s table, and the sliding table must travel parallel to the saw blade. Step 21 To level the Sliding Table with the machine table, loosen the Locking Levers (#36) in the Fence Mounts (#43) and slide the Fence over the machine’s table. Move the Sliding Table back and forth and observe the gap between the bottom of the Fence and the top of the machine’s table. The gap between the Fence and the machine’s table should remain the same throughout its travel. This is accomplished by adjusting the height of the rail Mounting Plate (#3-A) relative to the table surface of the machine and by adjusting the height of the legs (#7) that support the Outer Rail Tube and by locking the Legs in position with the Set Screws (#11). Step 22 The Sliding Table must travel parallel to the saw blade, which should be parallel to the miter guide slot in the saw table. With the Fence installed at the front of the Sliding Table, align the right hand end of the Fence with the edge of the miter guide slot. Using the Locking Levers (#36), lock the Fence in this position and move the Table back and forth through its travel. The right hand end of the Fence should ‘track’ and remain at the edge of the miter guide slot throughout its travel. If the right hand end of the Fence drifts to the left or right of the miter guide slot, the Outer Rail tube (#2-S) that guides the Sliding Table may not be parallel to the miter guide slot. First, check to be sure there is no play between the Bearings (#60B) and the Outer Rail Tube (#2-S). To adjust the Outer Rail Tube, loosen the Hex Head Bolts (#12) that secure the Diagonal Braces (#8-AS, BS & CS) to the Leg Mounts (#6-S) and shift the Outer Rail Tube to the right or left as required. Make sure there is some clearance between the right hand side of the Inboard Channel (#66) and the Inner Rail Tube (#1-S). Repeat Step 22 to check the travel. Tighten all the Bolts (#12). Step 23 Fig. 2C The Degree Scale (#24-S) is held in the top of the Angle Adjustment Rail (#23-S) tightening the two Hex Head Bolts (#29) inserted into the backside of the Rail. .

To square the Fence to the saw blade, install the Fence at the front of the Table. Using a large tri-square lock the Fence to the Table at 90° to the saw blade. Loosen the Hex Head Bolts (#29A). Position the Angle Adjustment Rail (#23-S) and Degree Scale (#24-S) with its ‘0’ mark at the face of the Fence. Tighten the Hex Head Bolts Step 24 With the Fence (#40-S), at the front of the Table (20-SS) and locked at 90 degrees to the saw blade, turn the Stop Tab (#26) to its vertical position and adjust the threaded Stop (#18) to touch the rear side of the Fence. Lock the Stop in position with the Wing Nut (#35). To remove the Fence from the Sliding Table turn the Stop Tab ‘down’ to a horizontal position. Loosen the Locking Knob (#44) and pull the Carriage Bolt (#45) and the Retainer (#75) from the T-slot in the top of the Angle Adjustment Rail (#23-S). Loosen the Locking Lever (#36) in the Table Mount (#25) and Lift the Pivot Post (#59) up, out of the Table Mount. To position the Fence at the rear of the Table at 90 degrees to the saw blade, the Pivot Post (#59) and Locking Tube (#47), installed on the backside of the Fence (#40-S), must be reversed because the Fence will be turned 180 degrees. Remount the Fence and adjust the treaded Stop at the rear of the Table. Step 25 With the Fence installed at the front of the Table affix the adhesive Tape Measure (#55) to the Tape Slide (#41-S). The Tape Slide is held in the Fence by tightening two ¼-20 x ¾” Bolts (#29) inserted into the backside of the Fence. As you are not likely to have the right hand end of the Fence touching the saw blade you may want to have the Measuring Tape start at the ½” or 1” mark .Scribe a corresponding reference mark on the saw table to synchronize the Measuring Tape to the saw blade. MAKE SURE THAT THE FENCE WILL NOT COME IN CONTACT WITH THE SAW BLADE THOUGHOUT ITS TRAVEL. NOTE: If you are relying on the Tape Measure for accuracy, remember that when you change (the thickness of your) saw blades, to adjust the Fence and/or Tape Slide accordingly.

14

EX26S & 26XS Parts Part# Qty Description ST01-S 1 Inner Rail Tube ST02-S 1 Outer Rail Tube ST03-A 1 Mounting Plate ST03-B 1 Mounting Bracket ST04-SS 4 Button Head Bolt

1/4-20 x 1/2” ST06-S 2/3 Leg Mount (26 or 26X) ST07 2/3 Leg (26 or 26X) ST08-AS 1 Diagonal Brace ST08-BS 1 Diagonal Brace ST08-CS 1/2 Rear Brace (26 or 26X) ST09 2 Rubber Bumper ST10 14/19 Hex Bolt (26 or 26X)

1/4-28 x 1/2” ST11 4/6 Set Screw (26 or 26X)

1/4-20 x 3/8” ST12 10/14 Hex Bolt (26 or 26X)

5/16-18 x 3/4” ST13 10/14 Square Nut (26 or 26x)

5/16 x 18 ST14 6 Phillips Screw

#8-32 x 1/2” ST15-SS 6 Machine Screw 10-32x1/2” ST16 1/2 Rear Bracket(26 or 26X) ST17 2 Lower Bearing 5/8” Dia. ST18 2 Stop 1/4-20x1” ST19 4 Flat Washer 6mm ST20-SS 1 Table Top ST21-S 1 Lower Lip ST22-S 2 Anti Friction Strip (factory installed) ST23-S 1 Angle Adjustment Rail ST24-S 1 Degree Slide ST25 2 Table Mount ST26 2 Stop Tab ST27 2 Socket Head Bolt

1/4-20 x 1-1/4” ST28-SS 1 Bearing Support ST29 8 Hex Head Bolt

1/4-20 x 3/4” ST30 4 Button Head Bolt

1/4-20 x 3/4” ST31 17 Flat Washer1/4” ST32 2 Flat Washer 5/16” ST33 5 Wave Washer 3/8” ST34 8 Ny-Lock Nut 1/4-20 ST35 2 Wing Nut 1/4-20

ST36 5 Locking Lever 3/4” Stud ST38 6 Split Lock Washer 1/4” ST39 2 Lower Bearing Bracket ST40-S 1 Fence (45-1/2” long) ST41-S 1 Tape Measure Slide ST42 2 Extension Bar ST43 2 Fence Mount ST44 3 T-Locking Knob1/4-20 ST45 1 Bolt 1/4-20 x 3-1/2” ST46 2 Extension Block ST47 1 Locking Tube ST48 7 T-Nut ST49 2 Flip Stop Finger* ST50 2 Flip Stop Mount* ST51 2 Shoulder Bolt* 3/8-18 x 2” ST52 2 Ny-Lock Nut*

5/16-18 ST53 2 Locking Lever* 1-1/8” ST54 5 Thumb Screw

1/4-20 x 1” ST55 1 Tape Measure ST56 1 Clamping Bar ST57 1 Toggle Clamp ST58 1 Spindle ST58A 1 Rubber Tip ST59 1 Pivot Post with Knob

ST60 6 Bearing 1-1/8” ST61 7 Bearing Spacer ST62 3 Eccentric Adjuster ST63 1 Brake Lever ST64 1 O-Ring 5/8” Dia. ST65 6 Ny-Lock Nut 10-32 ST66-SS 1 Inboard Channel ST67 7 Button Head Bolt

1/4-20 x 1” ST68 2 Button Head Bolt

1/4-20 x 1-1/4” ST69 3 EXAKTOR Logo Label ST70 2 Wiper Brush ST71-SS 2 End Plate ST72-SS 2 Stand-off ST73-SS 4 Hex Head Bolt 5/16-18 x 1/2” ST75 1 Retainer ST81 1 Thumb Screw ST83 1 Support Plate *There are parts for two Work Stops included with the Sliding Table.

Sliding Table Accessories Work Stop Assembly EXAKTOR Sliding Tables are shipped with parts to assemble two Work Stops. Additional Work Stops are available. Insert a Shoulder Bolt (#51) through a Flip Stop Finger (#49), Wave Washer (#33) and Flip Stop Mount (#50). Secure the Bolt with a Ny-Lock Nut (#52) and tighten to eliminate any play between the Finger and the Mount.

Insert the threaded stub of a Locking Lever (#53) through Washer (#19) and Flip Stop Mount (#50) into a T-Nut (#48). Leave enough slack to slide the T-Nut into the T-slot on the topside of the Fence (#40-S). With the Measuring Tape synchronized to the saw blade, the Work Stop is placed in position relative to the saw blade by ‘flipping’ the Finger onto the top of the Fence against the Measuring Tape and locking the Mount in place.

Parts Qty. Description ST19 1 Flat Washer 6mm ST33 1 Wave Washer ⅜” ST48 1 T-Nut ST49 1 Flip Stop Finger ST50 1 Flip Stop Mount ST51 1 Shoulder Bolt ⅜-18x2” ST52 1 Ny-Lock Nut 5/16-18 ST53 1 Locking Lever 1⅛”

15

Sliding Table Accessories Panel Support Assembly EXAKTOR Sliding Tables are shipped with parts to assemble one Panel Support Additional Panel Supports are available. Insert the threaded stub of Thumb Screw (#81) though a Washer (#31) and up through the underside of Support Plate (#82) into a T-Nut (#48). Leave enough slack to slide the T-Nut into the T-slot on the underside of the Fence (#40-S).

The Panel Support can be positioned for use under the Crosscut Fence (#40-S) and/or under the Extension Block (#46)

Parts Qty. Description ST48 1 T-Nut ST81 1 Thumb Screw ST31 1 Washer ST83 1 Support Plate

16

Sliding Table Accessories Outboard Roller Assembly The Outboard Roller is an optional accessory for the Exaktor Sliding Table. To attach the Roller Bracket (#76) to the to the table Bearing Support (#28) use the following parts already on the table. Use the two Hex Head Bolts (#29A), Lock Washers (#38) and Flat Washers (#31) inserted through the elongated holes in the Roller Bracket and the lower lip of the Bearing Support (#28). Thread T-Nuts (#48) on the Hex Head Bolts (#29A) leaving enough slack to slide the T-Nuts into the T-Slot on the inboard side of the Angle Adjustment Rail (23-S)

Using four Hex Head Bolts (#80) and four NyLock Nuts (#65) attach the two Roller Supports (#77) to the Roller Bracket (#76). Insert the Roller (#78-S) between the Roller Supports by compressing the Roller’s spring-loaded axel. NOTE: The top surface of the Roller and the Angle Adjustment Rail must be in the same plane and be level with the top surface of the Table. If necessary, shim between the Angle Adjustment Rail and The Bearing Support. Tighten the two Hex Head (#29A) Bolts.

Parts Qty. Description ST65 4 NyLock Nut ¼-20 ST76-S 1 Roller Bracket ST77 2 Roller Support ST78-S 1 Roller ST80 4 Hex Head Bolt ¼-20 x ½”

17

If You Need to Call Customer Service Please complete the following information for future reference: Model Number: EX26, EX26X, EX26S, EX26SX, EX40, EX60, EXOA-2, E100 (Circle your model number) Invoice Number: …………………………………………………… Date of Purchase: …………………………………………………. Place of Purchase: ………………………………………………… Retain this Owner’s Manual with your sales receipt as a permanent record of your purchase, in the event of theft, fire or warranty service. EXAKTOR® Numbers The Exaktor Solutions Center is our one-stop resource for all of your Exaktor tool needs. You can download the latest Assembly Manuals, read FAQ’s and troubleshooting tips. Visit us at:

http://solutions.exaktortools.com For Customer Service: 1-800-597-1343 (Voice – North America) 1-905-568-4459 (Voice – Outside North America) 1-905-568-4059 (Fax) Authorized Dealers: For the name of an Exaktor Authorized Dealer, call 1-905-568-4459 Important: We recommend that you keep all original packing materials, in the event that you ship this product.

18

19

EXAKTOR® ULTIMATE WARRANTY and EXCHANGE SERVICE

Following your thirty (30) day-trial period, this warranty gives you certain rights in addition to other rights you may have that may vary from jurisdiction to jurisdiction. This warranty is given only to the first end use purchaser of the accompanying product (referred to in this warranty as “this product”). What is covered: EXAKTOR® Tools Ltd, (“Exaktor”) warrants to you for the Warranty Period, that there are no defects in the materials or workmanship of this Product. The “Warranty Period” begins on the date you purchased this product and lasts as long as you are the original end use purchaser. What is not covered: Warranty WILL BE VOID by Exaktor for repairs or replacements made necessary due to the following: (1) the Product was not purchased from an authorized Exaktor reseller, (2) the Product has been modified by anyone other than an Authorized Service Representative of Exaktor, (3) any damage caused by accident, neglect, abuse or misuse of the Product, (4) Damages caused as a result of modification or alteration of the Product, (5) NOT COVERED UNDER WARRANTY ARE reasonable wear and tear where no defects in material and workmanship are found in the Product. What to do if you think your Product is defective: Call our Customer service Hotline at 1-800-597-1343. During the Warranty Period, supply Exaktor’s representative with information from your dated bill of sale showing that this product was purchased from an Authorized Exaktor Reseller. After contacting the authorized service center, you may be required to deliver or send the Product properly packaged, freight prepaid, to Exaktor’s Service Center together with a photocopy of your bill of sale. What Exaktor will do: Exaktor will evaluate your report of a possible defect to determine whether a defect exists, and if it does exist, Exaktor will repair or (at Exaktor’s option) replace the Product with a product that performs the same functions and performs as well as the original Product. Exaktor reserves the right to supply refurbished or remanufactured replacement parts provided that the replacement parts conform to the manufacturer’s specifications for new products. The repaired or replacement product will be returned to you at no cost. Exchange Service: When an exchange is authorized, Exaktor will exchange your non-working product with a refurbished or remanufactured product that conforms to the manufacturer’s specifications for new products. The refurbished or remanufactured Product you receive will be covered by the balance of the warranty period remaining on the original Product. You will keep the replacement Product that is sent to you and you must return (or be billed up to the cost of the new product) your original non-working product, which shall become the property of Exaktor. You must call Exaktor Customer Service and if the representative cannot correct the product’s malfunction over the telephone and you elect the exchange service, you must provide information pertaining to this Product and must also provide a valid credit card (Visa, MasterCard or AMEX) number. Your credit card will be charged up to the cost of a new Product if: (1) you do not return your original Product within ten (10) business days; (2) the malfunctions of your original Product are not covered by the warranty; (3) the Product was not properly packaged and has caused damage to the Product; (4) the original Product has not been sufficiently validated with a copy of the proof of purchase (bill of sale). The Exaktor Customer Service Representative will ship the exchange Product the next business day, with return instructions. You must return the original Product, Freight Prepaid, in the same shipping carton in which the exchanged Product was received and include a copy of proof of purchase (bill of sale). Retain your original accessory items and a copy of the courier’s bill, signed by the courier. Limitations : Repair or replacement as described above is your sole and exclusive (that is your only) remedy if this Product is defective. Exaktor shall not be liable for any direct, indirect, incidental or consequential damages or specific relief. Because some jurisdictions do not allow the exclusion or limitation of consequential or incidental damages, the above limitation may not apply to you. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, WHETHER EXPRESSED BY AFFIRMATION, PROMISE, DESCRIPTION, DRAWING, MODEL OR SAMPLE, AND ANY AND ALL WARRANTIES OTHER THAN THIS ONE, WHETHER EXPRESSED OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. This Warranty is the only warranty that Exaktor is giving for this Product. It is the final expression and the exclusive and only statement of Exaktor’s obligations to you. It replaces all other agreements and understandings that you may have with Exaktor or its representatives. This warranty (and Exaktor’s obligations to you) may not be changed in any way unless you and Exaktor sign the same piece of paper in which we (1) refer to this product and your bill of sale date, (2) describe the change to this warranty and (3) agree to make that change.