8/18/2019 EUMA Installation Guideline

1/7

Functions of the EMUA

 This describes the functions of the EMUA. Providing a variety of inputports for monitoringsignals, the EMUA supports real-time monitoring and remotemonitoring. In addition, theEMUA is highly reliable and can be e!ibly con"gured. It supports alarge area for temperaturemonitoring.

 The EMUA#$%& supports -#$ ' () po*er input, and the voltage canrange from -%+ '() to -& ' ().

8/18/2019 EUMA Installation Guideline

2/7

Exterior of the EMUA

8/18/2019 EUMA Installation Guideline

3/7

Internal Structure of the EMUA

8/18/2019 EUMA Installation Guideline

4/7

DIP Switch Setting

Silkscreen Function Setting

SW_ADDRSelection of thecommunication protocol

The settings of the DIP switchSW_ADDR is : 0010(If a DIP switch bit is set to ON, it represents 0. I f a DIP switch bit is set to OFF,it represents 1.)

SW_B!

Bit 1: water sensor settingThis "it is set to #$ if a sensor is not use%&This "it is set to #'' if a sensor is use%&

Bit (: smo)e sensor setting This "it is set to #$ no matter whether a sensor is use%&

Bit *: infrare% sensor settingThis "it is set to #$ if a sensor is not use%&This "it is set to #'' if a sensor is use%&

Bit +: %oor status sensor setting

This "it is set to #$ if a sensor is use%&

This "it is set to #'' if a sensor is not use%&

SW_T,!

Bit 1: temperature sensor settingThis "it is set to #$ if a sensor is use%&This "it is set to #'' if a sensor is not use%&

Bit (: humi%it- sensor settingThis "it is set to #$ if a sensor is use%&This "it is set to #'' if a sensor is not use%&

SW_A!'our "its for analog signal sensorsettings

This "it is set to #$ if a sensor is use%&This "it is set to #'' if a sensor is not use%&

SW_A.'our "its for analog signal sensorsettings

This "it is set to #$ if a current/t-pe sensor is use%&This "it is set to #'' if a oltage/t-pe sensor is use%&

SW1(ASW1(BSW(+A

SW(+B Thirt-/two "its for Boolean signal input

Bits 1/2 of the DIP switch SW1(A correspon% to input signals 1/2&Bits 1/2 of the DIP switch SW1(B correspon% to input signals 3/14&Bits 1/2 of the DIP switch SW(+A correspon% to input signals 15/(+&Bits 1/2 of the DIP switch SW(+B correspon% to input signals (6/*(&When a "it is set to #$ it represents high/leel alarms&

When a "it is set to #'' it represents low/leel alarms or is not use%&

8/18/2019 EUMA Installation Guideline

5/7

Position

The EMUA can be installed inside

T%/00 cabinet or AMP%0 cabinet

8/18/2019 EUMA Installation Guideline

6/7

)able connection

8/18/2019 EUMA Installation Guideline

7/7

External alarm position on EMUA board

Position On EMUA External Alarm Name

S1 A/Alarm 7enerator Switch

S( ,igh temp& power room 8 (6 Degrees

S* A/Alarm #er/tension controller 'ailure

S+ A/Alarm Power 9ontroller Phase 1/*S6 Intru%er alarm telecom room

S4 #n site telecom room

S5 ,igh temp& telecom room 8 (6 Degrees

S2 ow temp& telecom room ; 10 Degrees

S3 7enerator in #peration

S10 Batter- 9harge Alarm < ow Batter- .oltage

S11 Aircraft #"struction ight Alarm

S1( A Alarm ow 'uel

S1* A/Alarm 7enerator 'aile%S1+ Rectifier =ains Power 'ailure

S16 ow temp& power room ; 10 Degrees

S14 A/Alarm Rectifier  

S15 B/Alarm Rectifier  

S12 'ire Alarm

S13 Intru%er alarm power room

S(0 #n site power room

S(1 9logge% 'ilter A91