Upload
sylvia-holland
View
228
Download
5
Tags:
Embed Size (px)
Citation preview
ERT 319ERT 319Industrial Waste Industrial Waste
Treatment Treatment
Semester 1 2013/2014Semester 1 2013/2014
Solids Waste Treatment &
Disposal
Introduction• Constituents removed in WW treatment
plant:– Screenings, Grit, Scum, Solids and biosolids (also
known as sludge)– Biosolid - Class A & Class B
• Handling of solids and biosolids are complex because:1. It composed largely of substances responsible for the
offensive character of untreated WW2. Portion of biosolids produced from biological treatment is
offensive3. Only a small part is solid matter
SOLID PROCESSING METHODS (page 1450)
Solids Sources, Characteristics, & Quantities
Sources - Vary according to the type of plant and its method of operation
Characteristics- Vary depending on the origin of the solids, the amount of aging that
has taken place, and the type of processing to which they have been subjected.
GENERAL COMPOSITION
Quantities
- The volume of sludge depends mainly on its water content and only slightly on the character of the solid matter.
- A 10 % sludge, for example, contains 90 % water by weight. - If the solid matter is composed of fixed (mineral) solids and volatile
(organic) solids, the specific gravity of all of the solid matter is:
- Volume of sludge:
Ssl = specific gravity of sludge
Also, the volume varies inverse with percent of solid matter in the sludge,
matter solidof percentP
volume sludgeV
P
P
V
V
2
1
2
1
Example 14-1 Volume of Untreated and Digested SludgeDetermine the liquid volume before and after digestion and the
percent reduction for 500 kg (dry basis) of primary sludge with the following characteristics:
Primary Digested
Solids, %
Volatile matter, %
Specific gravity of fixed solids
Specific gravity of volatile solids
5
60
2.5
≈ 1.0
10
60 (destroyed)
2.5
≈ 1.0
Solution (pg 1459)
1. Compute the average specific gravity of all solid2. Compute the specific gravity of primary sludge3. Compute the volume of primary sludge4. Compute the percentage of volatile matter after digestion5. Compute the average specific gravity of all solid in digested
sludge6. Compute the specific gravity of digested sludge7. Compute the volume of digested sludge8. Determine the percentage reduction after digestion
PFRP and PSRP –to meet pathogen and vector reduction requirementPSRP –reduce but do not eliminate!
Solids Processing Flow Diagrams
THICKENING
THICKENING• Used to increase solid content of sludge by removing
removing a portion of liquid fraction• Usually accomplished by physical means; e.g settling,
flotation, centrifugation, gravity belt and rotary drum.• Why is it important?
1. Beneficial to the subsequent treatment processes from the following stand points:• Capasity of tanks and equipment required• Quantity of chemical required for sludge conditioning• Amount of heat (in digester) and fuel required for heat drying
and incineration
2. Cost reduction-small pipe size and pumping cost
3. Liquid sludge can be transported easily
• In designing thickening facility, it is important to:– Provide adequate capasity to meet peak demand– Prevent septicity, with its attendant odor
problem.
Gravity belt thickener
Schematic diagram : CENTRIFUGAL THICKENING
STABILIZATION--DIGESTIONS--
• Stabilization process of sludges for volume reduction, production of usable gas (methane), and improving the dewaterability of sludge
• Solids and biosolids (sludge produced from primary or secondary treatment) are stabilized to:- reduce pathogens- eliminate offensive odors- inhibit, reduce, or eliminate the potential for
putrefaction (decay, decompose of organic matters). Therefore, stabilization involves the reduction of volatile
content and addition of chemicals to solid and biosolid
Not suitable for survival of microb
Alkaline Stabilization- A method to eliminate nuisance conditions in sludge is
through the use of alkaline material to render the sludge unsuitable for the survival of microorganisms.
- In alkaline stabilization process, lime is added to untreated sludge in sufficient quantity to raise the pH to 12 or higher.
- When the pH is high: creates environment that stops or substantially retards the microbial reactions that can otherwise lead to odor production and vector attraction.
the sludge will not putrefy, create odors, or pose a health hazard so long as the pH is maintained at this level.
also inactivate virus, bacteria and other microbes present.
Application of Alkaline Stabilization Processes:1)Lime Pre-treatment
- addition of lime to sludge prior to dewatering- addition of lime to sludge prior to dewatering
2) Lime Post-treatment- addition of lime to sludge after dewatering
3) Advanced Alkaline Stabilization
ANAEROBIC DIGESTION
• Involves the decomposition of organic and inorganic matter (principally sulfate) in the absence of molecular oxygen.
• Major application: in the stabilization of concentrated sludge produced from the treatment of municipal and industrial wastewater.
• Can produce sufficient digester gas (methane) to fulfill the energy (heat & electricity) needs.
Design Factors of Anaerobic Digester.1) Solids & Hydraulic Retention Times
- Solids retention time (SRT) average time the solids are held in the digestion process (Mass / day)- Hydraulic retention time, τ average time the liquid is
held in the digestion process (Volume /day)- Digestion systems without recycle SRT = τ- Hydrolysis, fermentation and methanogenesis (3- reactions in anaerobic process) are directly related to SRT- If the SRT < min. SRT in each reaction, bacteria cannot grow
rapidly enough digestion fails
2) Temperature- determines rate of digestion - rates of hydrolysis &
methane formation- mostly operates in mesophilic temperature - between 30-38⁰C (or thermophilic T 50-57 ⁰C)- important since bacteria of methane-formers are
sensitive to temperature changes (ex: ΔT > 1 ⁰C/d affect performance, thus ΔT < 0.5 ⁰C/d is recommended)
3) Alkalinity- Ca, Mg and ammonium bicarbonates are examples of buffering substances found in a digester.- Digestion process produces ammonium bicarbonate from the breakdown of protein in the raw sludge feed (others found in feed sludge)- The concentration of alkalinity proportional to the solids feed concentration.- Alkalinity mostly in well-established digesters 2000 – 5000 mg/L.
- The principal consumer of alkalinity is CO2, i.e., CO2 is produced in fermentation and methanogenesis phases . Due to partial pressure of gas in a digester, the CO2 solubilizes and forms carbonic acid, which consumes alkalinity.- Therefore, CO2 concentration is reflective of the alkalinity requirements.
Single-stage High Rate DigestionHeating, auxiliary mixing, uniform feeding, and thickening of
feed stream- The sludge is mixed by gas recirculation, pumping, or draft-
tube mixers (separation of scum & supernatant does not take place), and the sludge is heated to achieve optimum digestion rates.
- With fixed roofs or floating covers
Two-stage Digestion- a high-rate digester is coupled in series with a second tank. - 1st tank: used for digestion, heated & equipped with mixing
facilities- 2nd tank: unheated, used for storage- This type of digester is seldom used because of expense of
large tank building and negligible benefit of 2nd tank.
Anaerobic digester
Example 14-5 Estimating Single-stage, High Rate Digester Volume and Performance
Estimate the size of digester required to treat the sludge from a primary treatment plant designed to treat 38 000 m3/d of wastewater. Check the volumetric loading, and estimate the amount of gas produced per capita. For the wastewater to be treated, it has been found that the quantity of dry volatile solids and biodegradable COD removed is 0.15 kg/m3 and 0.14 kg/m3, respectively. Assume that the sludge contains about 95% moisture and has a specific gravity of 1.02.
Other pertinent design assumptions are as follows:1. The hydraulic regime of the reactor is complete-mix2. SRT = τ = 10 days at 35 ⁰C3. Efficiency of waste utilization (solids conversion) E = 0.704. The sludge contains adequate nitrogen and phosphorus for
biological growth.6. Constants are for a temperature of 35 ⁰C. 7. Digester gas is 65 % methane. 8. Volume of methane produced: 1359 m3/d
Aerobic Digestion• To meet Processes to Significantly Reduce Pathogens
(PSRP) requirement (see Table 14-9, 14-10, 14-11 & 14-12, pg 1462-1465)
• Used to treat: waste-activated sludge only mixtures of waste-activated sludge or trickling filter sludge
and primary sludge Or waste sludge from extended aeration plants
• Plant capacity may up to 2 m3/s
Advantages compared to anaerobic digestion:
i- volatile solids reduction in a well-operated aerobic digester is approximately equal to that obtained anaerobically
ii- lower BOD concentrations in supernatant liquoriii- production of an odorless, humuslike, biologically stable end
productiv- recovery of more of the basic fertilizer values in the sludgev- operation is relatively easyvi- lower capital costvii- suitability for digesting nutrient-rich biosolids
Disadvantages of aerobic digestion: High power cost is associated with supplying the required
oxygen Digested biosolids produced have poorer mechanical
dewatering characteristics The process is affected significantly by temperature, location,
tank geometry, concentration of feed solids, type of mixing/aeration device, and type of tank material
Useful byproduct such as methane is not recovered.
Eqs 14-16 – 14-18:- conversion of organic nitrogen to nitrate results in an
increase in the concentration of H2 ions decrease pH, if sufficient buffering capacity is not available.
- About 7 kg of alkalinity (as CaCO3) are destroyed per each kg of ammonia oxidized. about 50 % of the alkalinity consumed by nitrification can be recovered by denitrification.
Eq 14-19 Eq. 14-20
a) Batch operation type with air additionb) Continuous operation type with air addition
Design criteria for aerobic digester
Figure 14-31Volatile solids reduction in an aerobic digester as a function of digester liquid temperature and digester sludge age (or SRT)
THANK YOUTHANK YOU