Equipment and Specification Required for Smart Class

At University Hall

A. List of equipment

S. No. Item Description Quantity

1. Integrated Digital Podium 1

2. Ultra Short Throw LCD Projector 1

3. 120” Motorized Screen with remote control 1

4. HD Video Conferencing System : System components –

CODEC, HD PTZ Camera (2), Microphone and Remote

Control

1

5. Full HD 55” LED TV 3

6. Rack mounted HDMI Matrix Switcher 1

7. HDMI Audio De- Embedder 1

8. HDMI Twisted Pair Transmitter 1

9. HDMI Twisted Pair Receiver 1

10. All devices control system with Touch panel 1

11. Server based Recording and streaming System with software 1

12. 5KVA Online UPS with 60 minutes battery backup 1

13. Table Gooseneck Microphone (1 Chairman Mic and 49

delegate mics)

50 Nos.

14. Digital Signal Processor with Front Panel Display for Sound

Reinforcement with Automatic Mixer, Matrix Mixing, Power

Amplifiers with Software

1 set

15. Digital interfacing and all digital cable connectivity to

integrate all the equipment

1Lot

16. Installation/Configuration/Integration/Commissioning/Training 1 Job

B. WI-FI LAN Work along with equipment

1. Supply, laying, termination and testing of UTP CAT 6 Cable

with casing and capping for Networking of AP complete with

necessary ferrule numbering at both the ends of each piece of

cable complete.

1box (305 Mtr)

2. Supply, installation, testing and commissioning of CAT - 6

Information outlets (I/O) with face plate and flush PVC box

complete to be installed concealed in wall.

5

3. Supply, installation and fixing of 24 port Gigabit Fast

Ethernet Web Managed L2 PoE Switch

1

4. Supply, installation and fixing of 300 Mbps Wireless Access

Point with PoE Support

3

5. Patch Cord Cat 6 UTP Blue 1m - Moulded 6

6. Patch Cord Cat 6 UTP Blue 2m - Moulded 6

7. Supply, installation and fixing of Patch Panel Cat 6 UTP

Modular -24 Port- Loaded 0.5U Height

1

8. Supply, installation and fixing of 9 U Wall Mount Rack with

Accessories

1

A. Equipment Specifications:

1. Integrated Digital Podium

I. Stand Type, Solid Built housing with steel / Fiberglass / rubber wood.

II. Provided with locking system to prevent theft Soft wheels for convenient transport.

III. Sliding Door with Wooden material to protect Tablet Monitor and as Laptop Stand.

IV. Equipped with LCD Tablet Monitor with 19 inches or wider tablet monitor with

1920×1080 resolution or more and must have following features

Aspect Ratio 16:10

Active Area Minimum 477(H)×268(V)

Brightness Minimum 250cd/m2

Contrast Ratio 1000:1

Viewing Angle 160°(H/V)

Hight Adjustment Motorised Control of height through button

Software Functions

writing, annotation, erasing, recording of session with video, cut & paste of annotated images, multi-flag pages available for short notes, facility of making e-book, dual page option, fit to curve, multi color page insert , insertion of video MS office file etc for annotation.

V. Standard Electronic Pen for writing on Tablet Monitor.

VI. Trainer Laptop interface terminals and slots to use a laptop.

VII. Gooseneck adjustable Mic to fit user’s height with good acoustics to attain good

Quality Audio

VIII. Standard mouse for navigation during training.

IX. Drawer for keeping material required for trainer.

X. 6” or Higher LCD Control Panel for Multi controller which utilizes and control all

the devices in the lecture room such as interactive whiteboard, TV, DVD, air

conditioner, PC, projector, large-sized screen etc.

XI. Podium must be equipped with automatic mixer, Power Amplifier etc. which can

support upto 8 column line array speaker, 4 wireless Microphone and 2 lapel

Microphone.

XII. 8 Speakers set having output 120W @ 4 ohm or more, Frequency range 52.9 ~

12,000Hz, Sound Pressure Level 96dB, Total harmonic distortion 0.1% (1kHz) or

better

XIII. 3 Wireless Hand held Microphone system and two lapel microphone system.

XIV. Podium must be equipped with presentation switcher (video scaler) that accepts and

scales a wide range of video signals to a common, high resolution output rate. It can

accommodate two composite video, two S-video, one standard or high definition

component video, one DVI-D, and two RGB computer-video sources. It must be

capable to support 4LED TV, one Projector output and 2 PTZ camera.

XV. Podium must be equipped with One-Gang WPB Wallplate for HDMI, VGA, and

Stereo Audio

XVI. Digital Podium should have sufficient space for installing a PC, Visualiser,

Amplifier, Controller, Wireless Receiver must.

XVII. Equipped with Document Visualizer with following specification:

i. SXGA (1280 × 1024) High Quality Resolution, up to 20 frame rate per

second or Better

ii. Image Sensor 1/2” 1.3M Pixels CMOS or Better

iii. Manual Focus Function

iv. Digital 7X Zoom or more

v. USB Cable PC Interface

XVIII. Equipped with PC of internationally known brand like HP, IBM, Dell etc

i. Processor: Intel Core i7-2600, 3.4 GHz, 8MB cache or better

ii. Chipset: Intel Q67 or higher on OEM motherboard

iii. Memory: 3GB DDR3 RAM

iv. HDD: 320 GB @7200 RPM SATA or higher

v. DVD ROM Drive: 8X or better

vi. OS: Preloaded Windows 8

vii. NIC: 10/100/1000 on board integrated network port and GiGa bit Wi-Fi Card

viii. Preinstalled MS Office 2012 Professional (Academic Version) or higher

ix. Preloaded Antivirus with one year subscription

XIX. One year onsite comprehensive warrantee

2. Ultra Short Throw HD LCD Projector

1. Display Technology DLP

2. Native Resolution XGA 1024 x 768 or better Should support upto WUXGA ( 1920 x 768 )

3. Brightness 5000 lumens or better

4. Lamp Life 3500 hours or better

5. Contrast Ratio 4000:1 or better

6. Input Connections Should have minimum 2-VGA for 2 computer Inputs ,1XHDMI 19-pin, 1X LAN Port, 1XComposite Video,1X

S-Video,1X 3.5mm Audio In, USB Mini-B , VGA Out

7. Aspect Ratio Should have 4:3 and should support 16:9

8. Audio 2 Watt or better

9. Video Compatibility SDTV and HDTV or better

10. 3D capable Should Support PC Based 3 D Content or Better

11. Scan Freq Horizontal Scan Freq 15-101 KHz Vertical Scan Freq 24-120 Hz or Better

12. Keystone Correction Vertical +-30 degrees or Better

13. Features

3. 120” Motorized Screen with remote control

1 Size 120” (Diagonal)

2 Aspect Ration 4:3

3 Vie Angle 160 degree

4 Other Features Free to stop any location

Super high grain

Matt white fabric

Screen should be retractable and can be operated (pull down and wound back) via remote and preferably wireless remote control.

Screen should be supplied with wall mounting / fixing kit.

4. HD Video Conferencing System : System components – CODEC, HD PTZ

Camera (2), Microphone and Remote Control

(a) CODEC : Hardware based meeting the following minimum specifications: I. Signaling Protocols H.323 II. Bandwidth : H.323 / SIP up to 6 Mbps (p2p), : H.323 / SIP up to 2 Mbps

III. Network Protocol : IPv4 and IPv6. IV. Video Standards: H.263, H.264 and H.239 V. Video Resolution : Full HD, 1920 X 1080 @30ps, 720p@60fps VI. Video Features: Native aspect ratio 16:9; Picture-in-picture and side-by-side

view of remote and local; self-vie, All resolution progressive scanning. VII. Video Input :

a. 3xHD PTZ cameras. b. 1xDVI input for connecting Desktop PC/Laptop for content sharing

(along with PC audio for multimedia contents) VIII. Video Output : 2 x HDMI/DVI /HD Video Out for connecting primary and

secondary monitors. IX. Audio Quality: Full duplex audio with echo cancellation, automatic noise

suppression and automatic gain control, X. Audio Standards: G.711, G.722, G.722.1, and G722.1C/MPEG-4 AAC-LD

XI. Audio Input: 2 or more Microphone input for connecting external omni-directional wired microphone. 2 x Stereo / MicLine-in (3.5mm Jack), 1X RJ-45, 1X HD Video-In, 1X DVI-In, 1X HD Camera-In (Focus)

XII. Audio Ouput: 1X RJ-45, 1X Stereo Line-out, 1X HD Video-Out, 1X DVI-Out XIII. Network Interface : Minimum 1 port 10/100/1000 Mbps Ethernet interface.

Support for NAT and Firewall Traversal, 1 RJ-45 for Phone, 1X RJ-11 for analog phone, 1X 3.5 mm Mic-In for Microphone

XIV. Security : Secure password authentication, H.235 (AES) encryption XV. QoS : DiffServ, IP Precedence, Adaptive QoS, Dynamic bandwidth allocation,

Forward Error Correction XVI. Supports : Diagnostic and management functionality, Directory services, Far-

end camera control XVII. IP based recording – One button recording to centralized IP based recorder

without loosing any multiparty port XVIII. User Interface : Infrared remote Control for full functionality XIX. Embedded HD Multipoint Control Unit: Full HD CP MCU with upto 4 participant,

Upto 4-way 720p@30fps, 720p@60fps, 1080p@30fps Virtual multiway allows participant viewing control.

Note 1 : Three HD PTZ cameras can be connected to the CODEC either directly meet classroom requirement explained under ‘scope of work’.

The CODEC should have at least one HDMI/DVI/HD-SDI port for connecting any 3rd Party HD PTZ Camera. This may be controlled either through its own remote control or through GUI application running in Tablet/Laptop.

(b) Camera : I. Should be separate Full HD PTZ camera with wall and ceiling mounting fixtures

(One of the cameras will be mounted on the wall and others will be hung from the ceiling) and having the following minimum specifications.

II. Image sensor : 1/3” CMOS/CCD III. Native output : Full HD, 1920 X 1080 @30ps, 1280X720p@60fps IV. Zoom : Optical :12X or better V. Format:16:9 aspect ratio VI. Focus : Manual and Auto

VII. White Balance : Manual and Auto VIII. Iris : Manual and Auto IX. Video Output : HD output compatible to HDMI/DVI. For any other interface

standard, it should be possible to connect the camera to CODEC either directly or through suitable converters.

X. Presets : ≥ 10 Note : It has been assumed that the same camera will be used for both wall and ceiling mounting.

5. Full HD 55” LED TV

1. Size 55" Diagonal Size

2. Resolution 1,920 x 1,080, (16.7 Million Display Color)

3. Aspect Ratio 16:9

4. Pixel Pitch 0.21(H) x 0.63(V)mm

5. Active Display Area 1209.6 (H) x 680.4 (V) mm

6. Brightness 350 cd/㎡

7. Dynamic Contrast Ratio 100,000:1

8. Viewing Angle (Horizontal / Vertical):

178 / 178 °

9. Response Time 8 ms

10. Connectivity Analog D-SUB, DVI-D (Dual Link),Component, CVBS, HDMI,Input Audio: Stereo Mini Jack,Output Audio: Stereo Mini Jack,RS232C (In/Out), RJ45

11. General Feature

Slim & Light LFD with Built-in Scheduler , can display scheduled contents automatically Built in Speaker (10W + 10W), Plug and Play ,Display PPT etc (through USB), PIP/PBP, Narrow Bezel, Light Weight

6. Rack Mounted HDMI Matrix Switcher

VIDEO Routing HDMI 8 x 8 matrix Switcher

Signal type: TMDS digital RGB and single-link DVI digital video signals are supported

Digital video : RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI and HDMI [if using an optional adapter] standards from 640x480 @ 60 Hz to 1600x1200 @ 60 Hz computer video and HDTV 480p, 720p, 1080i, 1080p)

Digital audio : Supports HDMI audio transmitted through the RGB and Y, Cr, Cb lines, actively buffered.

EDID and DDC:

Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered.

HDCP: Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI 1.3 standards

HPD

Resolution range Up to 1080p (HDTV) or 1920x1200 (the highest resolution of the single-link DVI standard) @ 60 Hz

Maximum data rate 6.75 Gbps (2.25 Gbps per color),Maximum pixel clock: 225 MHz

Standards : DVI 1.0, HDMI 1.3

Switching speed 200 ns, max

Impedance 100 ohms

Return loss <-15 dB @ 1 MHz to 1.5 GHz

TDR rise time (10%-90%) 75 ps

Equalization Automatic

VIDEO OUTPUT

Number/signal type: 4 or 8 (depending on model) digital RGB

Connectors: 4 or 8 female HDMI type A

Nominal level : 1.2 Vp-p

Minimum/maximum level(s) : 0.5 V to 1.0 Vp-p with no offset (follows input)

Impedance 100 ohms

Return loss : <-15 dB @ 1 MHz to 1.5 GHz

DC offset ±500 mV maximum with input at 0 offset

Rise and fall time :(20-80%) 0.6 ns

Re-clocking : Automatic

Peripheral device power 250 mA per output

CONTROL/REMOTE — SWITCHER

Serial control port : 1) RS-232, 9-pin female D connector

(1) RS-232, front panel 2.5 mm mini stereo jack

Serial control pin configurations:

9-pin D connector 2 = Tx, 3 = Rx, 5 = GND

Mini stereo jack Tip = Tx, ring = Rx, sleeve = GND

Ethernet control port 1X RJ-45 female connector, 10/100Base-T, half/full duplex with autodetect

Ethernet protocol ARP, ICMP (ping), IP, TCP, DHCP, HTTP, Telnet

Default settings :Link speed and duplex level = autodetected

7. HDMI Audio De- Embedder

VIDEO:

Maximum data rate 675 Gbps (2.25 Gbps per color),Maximum pixel clock 225 MHz

Resolution range Up to 1920x1200 or 1080p @ 60 Hz, 12-bit color

VIDEO INPUT

Number/signal type – 1 single link HDMI

Equalization Automatic for up to -12 dB of cable loss

Input cable length Up to 25’ (7.6 m)

VIDEO OUTPUT

Number/signal type 1 single link HDMI

AUDIO INPUT

Number/signal type 1, combined with HDMI video input

Source formats PCM, Dolby Digital 2/0, Dolby Digital 2/0 Surround, Dolby Digital 5.1, Dolby Digital EX, DTS Digital Surround 5.1, DTS-ES Matrix 6.1, DTS-ES Discrete 6.1

AUDIO OUTPUT

Number/signal type 1 combined with HDMI video output and either1 stereo balanced/unbalanced or 1 S/PDIF

Connectors (1) 3.5 mm captive screw connector, 5 pole1 female RCA jack (tip, ring)

CONTROL/REMOTE

USB control ports 1 front panel female mini USB B

8. and 9. HDMI Twisted Pair Transmitter and Receiver

Video

Resolution Range up to 1920 x 1200 or 1080p @ 60 Hz ,80,10 or 12 bit color depth

Maximum Data Rate 6.75 Gbps ( 2.25 Gbps per color)

Video Input -Transmitter Connectors 1 female HDMI Type A

Interconnection between Transmitter & Receiver

Connectors 1 female RJ-45 per unit Signal Transmission Distance Up to 230'(70m) using CAT 5e//6/6a/7 UTP or STP Cable (solid conductor 24 AWG or better)

Video Output- Receiver Connectors – 1female HDMI Type A

Audio Input Number/ Signal Type -1 PC Level stereo, Unbalanced

Audio Output

Number Signal Type – 1stereo (2Channel), Balanced/Unbalanced

Control / Remote External device( pass through ,unidirectional or bidirectional) Serial Control Port input / output

Transmitter

RS-232 Via 3.5mm,5 pole captive screw connector for RS-242 Control (±5V)(Connector is shared with IR Control Port)

Receiver 1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm

10. All devices control system with Touch panel

Memory SDRAM: 512 MB,Flash: 4 GB

Memory Card Memory Card: supports SD™ and SDHC™ cards up to 32 GB,:

External Storage support USB mass storage devices up to 1 TB

Authentication IIS v.6.0 Web Server; SMTP e-mail client; installer setup via Crestron Toolbox™ or MSIE[2] Cresnet®: Cresnet master mode

RS-232/422/485 For 2-way device control and monitoring, all ports support,RS-232 up to 115.2k baud with software handshaking, one port also supports RS-422 or RS-485 and hardware handshaking

IR/Serial Supports 1-way device control via infrared up to 1.2 MHz or serial TTL/RS-232 (0-5 Volts) up to 115.2k baud

RELAY OUTPUT 1 - 8: (2) 8-pin 3.5mm detachable terminal block comprising (8) normally open, isolated relays; Rated 1 Amp, 30 Volts AC/DC;

suppression MOV arc suppression across contacts

I/O 1 - 8: (1) 9-pin 3.5mm detachable terminal block comprising (8) “Versiport” digital input/output or analog input ports (referenced to GND);

Digital Input: Rated for 0-24 Volts DC, input impedance 20k Ohms, logic

threshold >3.125V low/0 and <1.875V high/1;

Digital Output: 250mA sink from maximum 24 Volts DC, catch diodes for use with “real world” loads;

IR SERIAL OUTPUT 1 - 8: (2) 8-pin 3.5mm detachable terminal block comprising (8) IR/Serial output ports; IR output up to

1.2 MHz;

COM 1: (1) 5-pin 3.5mm detachable terminal block;Bidirectional RS-232/422/485 port; Up to 115.2k baud; hardware and software handshaking support

COM 2-3 (2) 3-pin 3.5mm detachable terminal blocks;Bidirectional RS-232 ports;Up to 115.2k baud; software handshaking support

MEMORY: (1) SD memory card slot;Accepts one SD or SDHC card up to 32 GB for memory expansion

USB (1) USB Type A female;USB 2.0 port for storage devices

LAN (1) 8-wire RJ45 jack; 10Base-T/100Base-TX Ethernet port and support for Ethernet: 10/100 Mbps; auto-switching; auto-negotiating; auto-discovery;full/half duplex; industry-standard TCP/IP stack; UDP/IP; CIP; DHCP; SSL;IEEE 802.1X; SNMP; BACnet®/IP[1]; IPv4 or IPv6; Active Directory

Cresnet master port; Outputs power to Cresnet devices if a power pack is connected to the 24VDC power input jack;

Other Ports 8 IR/serial, 8 relay, and 8 Versiport I/O ports

Other Features With Touch Panel and all necessary software to ensure proper functioning , pls. take in to note the desired relay or any other Hardware if required is included in the offer to control all tendered items

11. Server based Recording and streaming System with software

1. It must be appliance/Hardware server based & 19 inch Rack mountable.

2. Hardware system should have one Intel Xeon Processor E5 2630(6 Core) 2.3 GHz/1333 MHz/

Cache 15 MB L3 with 64 GB RAM (equivalent to HP/IBM/Dell)

3. Hardware system should have minimum 1TB disk storage capacity and in addition to storage

capacity, system should also be supplied with 12 TB NAS storage device so that it must support

minimum 1000 hours of recording@720p or higher resolution.

4. System must be supplied with the required software for recording of video session and take

video signals from video terminals / endpoints. Also it must support live video streams on the

network.

5. Concurrent Recording : Minimum 5 or more

6. Recording resolution support: Minimum 720p or higher

7. The system must support E-Learning application such as Knowledge sharing, viewing of

training session, lectures from remote location at any time.

8. Management control: Admin or User can control the applications from Web browser.

9. Video resolution support: H.264 video

10. Can record or Live stream video session along with data sharing/Presentations from the end

points to PC (MAC/WIN) &IPAD.

11. It must support Network ports/Ethernet: Min 1

12. The system must be capable of integrating into any LDAP environment. In particular, the

streaming/recording solution must allow administrators to integrate the solution with

Microsoft Active Directory/Microsoft Outlook.

13. Live Stream: System should support Multicast or Unicast

14. Viewing requirement at user end: Streaming and live video can run on flash or any video

player

15. Recorded video must have the function of Play, pause, forward, rewind, full screen on Laptops

(MAC/WINDOWS)

16. Should support multiple Web browsers like Internet Explorer (version 7 or 8), Chrome, Safari

on MAC OS, Firefox

17. NAT/Firewall transversal should be available

12. Five KVA Online UPS with 60 minutes battery backup

Isolation transformer with PWM Technology, Floor mounted type suitable for single phase

AC input voltage 160V to 260V, 50+/-1.5 Hz and single phase AC output voltage 230+/1%

V, 50+/-0.5 Hz.

Battery type: sealed lead maintenance free, Lead Acid tubular.

Output wave form : Pure sine wave

Warranty: 1Year on-site comprehensive warranty.

13. Table Gooseneck Microphone (1 Chairman Mic and 49 delegate mics)

Gooseneck with base and power switch with snap-fit foam windscreen

Gooseneck length 18”

Generation Element: Dual condenser, back electret

Frequency Response 70 to 17,000 Hz

Polar Pattern Cardoid

Maximum SPL (1kHz at 1% THD, 1 k-ohm load)

125.0 dB

Equivalent Output Noise (A-weighted)

21-29.0 dB SPL

Signal to Noise Ratio (referenced at 94 dB SPL)

65.0-75 dB

Dynamic Range with 1 k- >94.0 dB

Common Mode Rejection 45.0 dB minimum

Mute Switch Attenuation 50.0 dB minimum

Preamplifier Output Clipping Level (1% THD)

-6.0 dBV (0.5 V)

Polarity Positive sound pressure on diaphragm produces positive voltage on pin 2

14. Digital Signal Processor with Front Panel Display for Sound Reinforcement

with Automatic Mixer, Matrix Mixing, Power Amplifiers with Software

(Single or Multiple devices can be used to achieve below Features and

Specification)

A. DSP Input / Output Configuration

The following attributes are required

Should support minimum 50 Nos Gooseneck Mic Inputs

Should also support Input Gain Adjust, Mic or Line Level , Phantom Power on/off

Should support filtering for Low Pass, High Pass, PEQ

Should have facility for Mute on/off

Should have facility for Chairman Override on/off

Should have facility for AGC on/off

Should support Automatic Level Control on/off

Should support line input and line output for 120 Gooseneck mic, 10 Wall mount speaker

General Features o Features o AVB Compatible o Auto Mixer to prevent false gating to ambient Noise o Matrix Mixing / Routing for Mix-Minus Operation o -45 Port for Network Connection o RS 232 Port for Serial Control with External Control System o Front Panel LCD/LED Display for Edit Settings, Preset Activation, Gain

Changes etc. o Ability to View, Select, Calibrate Following:

No of Open Microphones Ambient Level Gate Threshold Adjust Off /Attenuation Adjust Hold Time Chairman Priority

o 19” Rack Mountable o Certification UL/CE

Power Amplifiers Channels To support 120 mic and 10 Wall mount

speaker

Output per channel 30 Watts (Min) in to 8 Ohm

Power Range 115/230v operation

Impedance S electable 8Ohms/70/100V

Monitoring Features Temp value, Fault etc.

Mountable 19” Rack

Certification UL/CE

B. Specification for Wi-Fi LAN Equipments

1. UTP CAT 6 Cable

Features

Category 6 Unshielded Twisted Pair 4 pair 100 Ohm cable

shall be compliant with ANSI/TIA/EIA-568-B.2-1 upto

600 Mhz.

Category 6 UTP cables shall extend between the work area

location and its associated telecommunications closet and

consist of 4 pair, 23 AWG, UTP Non Plenum cable jacket.

The 4 pair Unshielded Twisted Pair cable should be UL

Listed and ETL Certify.

Zero-Bit error throughput test as per IEEE standards

verified by ETL

The 4 pair Unshielded Twisted Pair cable should be RoHS

Compliant

Mechanical

Characteristics

Construction: 4 twisted pairs separated by internal X

shaped, 4 channel, full separator. Half shall not be

accepted.

Conductor Solid Copper

Insulator Polyethylene

Delay Skew : 35 ns MAX

Jacket PVC

Attenuation : 22.8dB/100m at 250MHz, 29.4dB/100m at

400MHz, 39dB/100m at 600MHz

2. CAT - 6 Information outlets (I/O) with face plate and flush PVC box

Features Surface Mount Face Plate & Box with CAT6 Work Area Data

I/O Outlet (RJ45) adhering to ETL Verification program for

compliance with TIA568B.2-1

Category 6, TIA568.B.2-1 – 600MHz

Information Outlet should be UL Listed and I/O box should be

RoHS Compliant

568A/B configuration

Be constructed of high impact with color and icon options for

better visual identification. Integrated hinged dust cover using

collapsible angular spring loaded shuttered technology.

Face plate should be Single Gang square plate and Should

have provision for Labe

Material ABS / UL 94 V-0

Port One

3. 24 Port Gigabit Fast Ethernet Web Managed L2 POE Switch

i. Port: 24 ports 10/100/1000Base-T and 2 ports 1000Base-X, 2 Giga SFP port

ii. Power Over Ethrenet (PoE)

Support for 802.3af,802.3AF

Power per port - 31Watts for 4 ports, Rest of the ports supports 15.4Watts

iii. Switching Capacity 52Gbps

iv. Forwarding Rate Min 35Mpps

v. MAC address 16K

vi. Vlan 256

vii. Jumbo Frane 9 K

viii. Features Auto Negotiation of port speed and Duplex Settings

IEEE 802.1wrapid Spanning Tree group

Loopback Detection IEEE 802.3ad Link Aggregation or equivalent IEEE 802.1p (Priority Queues) IEEE 802.1x security, Port based Mirroring

Support for IPv6 ix. VLAN Support 802.1Q VLAN

Private vlan

Traffic Segmentation

VLAN protocol

GVRP

Q-in-Q

x. Management Web based management interface

Through Telnet, HTTP and NMS.

Virtual LAN Management feature.

SNMP Version 1,2c

Firmware upgrade via Web

Remote Ping

Port statistics

xi. Quality of Service 4 hardware queues

Strict priority, weighted round-robinPriorityQueue

Scheduling

Queue assignment based on DSCP and class of

service

Bandwidth Control

o Egress : min 16Kbps Granularity

o Ingress : min 16Kbps Granularity

xii. Security Local Authentication with support for manual

Privilege definitions assignment

802.1x Authentication

Port Security

Automatic HTTPS redirection

DHCP Snooping

Defence Engine

IP Source Guard

Management Access Filter for

HTTP/HTTPS,SNMP,TELENT/SSH

Broadcast,Multicast,Unicast Storm Control Based

on Packets per seconds

Flow based Rate limiting based on Packets per

second (PPS)

4. 300 Mbps Wireless Access Point with PoE Support

Antenna: PiFa Antenna x 2 (2T2R MIMO Technology)

Port One 10/100Mbps 10/100 Ethernet Uplink port for AN

Push Button One WPS push button

Flash Memory Flash: 2MB

SDRAM: 16MB

Frequency band: 2.4000 ~ 2.4835GHz

Standard compliance IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

IEEE802.11b

IEEE802.11g

IEEE802.11n

RADIUS (IEEE802.1x)

Data Rate IEEE802.11b: 1/2/5.5/11Mbps

IEEE802.11g: 6/9/12/24/36/48/54Mbps

IEEE802.11n (20MHz): MCS0-15, up to 144Mbps

IEEE802.11n (40MHz): MCS0-15, up to 300Mbps

Output power IEEE802.11b @ 11Mbps: 26 +/- 1.5dBm

IEEE802.11g @ 54Mbps: 24 +/- 1.5dBm

IEEE802.11n (20MHz) @ MCS15: 23 +/- 1.5dBm

IEEE802.11n (40MHz) @ MCS15: 23 +/- 1.5dBm

Wireless mode Access Point

Wireless Client

Point to Point

Point to Multi Point

WDS

Universal Repeater

Wireless Security Protected Client Authentication

802.1x support

Static/Dynamic IEEE802.11 WEP Keys

WPA

WPA2

Certification: FCC part 15 Class B

CE

Power 5V DC, 2A Switching Power Adapter

IEEE802.3af Power-over-Ethernet

5. and 6. Patch Cord Cat 6 UTP 1m and 2m

Type Unshielded Twisted Pair, Category 6, TIA / EIA 568-B.2

Conductor 24 AWG 7 / 32, stranded copper

Length 7-feet for workstation and 3feet for Jackpanel / equipment

Plug Protection Matching colored snag-less, elastomer polyolefin boot

Warranty 25-year component warranty

Category Category 6

Housing Clear polycarbonate

Terminals Phosphor Bronze, 50 micron gold plating over selected area

and gold flash over remainder, over 100 micron nickel under

plate

Load bar PBT polyester

Jacket PVC

Insulation Flame Retardant Polyethylene

7. Patch Panel Cat 6 UTP Modular -24 Port- Loaded 0.5U Height

Type 24-port, Unshielded Twisted Pair, Category 6, TIA / EIA 568

Port Arrangement Keystone Krone type. Ports must be replaceable in 8 Port

Module.

Category Category 6

Circuit Identification

Scheme

Patch Panels Rear Cable Management without tie-wrap with

simplified numbering labels

Height . 5 U , to save the Rack space.