O O

FF

I ON

Wire connectionseOT16-32:Switch wire range: #18-8 AWG, 60-75 °C, Cu only, solid or strandedTorque: 7 lb.in, use Pozi-drive #2 or flat blade screwdrivereOT45-63:Switch wire range: #14-4 AWG, 60-75 °C, Cu only, solid or strandedTorque: 18 lb.in, use Pozi-drive #2 or flat blade screwdriverAuxiliary contacts, 10A, 600V, A600-R300Switch wire range: #18-14 AWG, 60-75 °C, Cu only, solid or strandedTorque: 7 lb.in, use Pozi-drive #2 or flat blade screwdriver

Optional Power PoleseOT16-32:OTPS40FPN2 4th pole OTPN40FP Solid neutral pole

Optional Auxiliary contactsOA1G10 (1 N.O.) Install on right side of switch. Max. 2 pcs on 3-pole switch, 1 pcs on 4-pole switch (eOT16-32).OA1G01 (1 N.C.) Install on left side of switch. Max. 2 pcs.OA2G11 (1 N.O. + 1 N.C.) Install on right side of switch.

Installation instructions

P/N AMPS Enclosure size VAC 200V 208V 240V 480V 600VeOT16_ 16A Size 1 HP 3 3 5 10 10eOT25_ 25A Size 1 HP 7.5 7.5 7.5 15 20eOT32_ 40A Size 1/ Size 2 HP 10 10 10 20 25eOT45_ 60A Size 2 HP 15 15 15 30 30eOT63_ 80A Size 3 HP 20 20 20 40 40

Ratings

ApplicationsThe eOT series of enclosed manual motor controllers are rotary operated, 3 or 4 pole, up to 600V HP rated switches, housed in thermoplastic enclosures suitable for humid and corrosive environments. They may be used for both indoor and outdoor applications. Available in Type 3R & 12 with selector and pistol grip handles and in Type 12, 4X with pistol grip handles. Products are properly installed on the load side of a branch circuit protective device and are suitable for use as motor disconnects.

Disconnecting means

Short circuit protective device

Controller

Overload protection

Motor disconnection

M

1SCC340014M0205 Document no. 34 EOT 16-63 P1 E

eOT SeriesEnclosed Manual Motor ControllersCatalog number: eOT16_, eOT25_, eOT32_, eOT45_, eOT63_

WARNINGTo avoid hazard of electric shock, turn off and lock out all power sources before installing or performing maintenance on this equipment.

eOT45-63:OTPS80FP 4th pole OTPN80FP Solid neutral pole

eOT Series Enclosed Manual Motor Controllers

InstallationOperate switch to the OFF position and loosen the cover screws, remove the cover.

eOT16_, eOT25_, eOT32_Two concentric 1/2" & 3/4" K.O.s are provided in the top and bottom of the enclosure (size 1).

eOT32_, eOT45_Two concentric 3/4" & 1" K.O.s are provided in the top and bottom of the enclosure (size 2).

eOT63_Two concentric 1" & 1 1/4" K.O.s are provided in the top and bottom of the enclosure (size 3).

eOT Series Enclosed Manual Motor Controllers

An internal metallic plate bonds together all conduit hubs installed, without the need for additional bonding jumpers.

• Drill proper holes for conduit hubs or use K.O.s• Install conduit hubs• Install enclosure size 1 and 2 using (2) #8 or M4 screws• Install enclosure size 3 using (4) 1/4" or M6 screws

WiringFor ease of wiring, it is recommended to remove the switch from the enclosure before pulling the wire. A small flat blade screwdriver may be used to release the DIN rail clip at the bottom of the switch, allowing it to be removed.

Connect power wires to switch terminal and attach ground wire to the ground terminal block inside the enclosure. Reinstall the switch in the enclosure. Reference the National Electric Code and all local codes for appropriate wire size and grounding requirements.

Pozi-drive #2 or flat blade screwdrivereOT16-32: Torque 7 lbs/ineOT45-63: Torque 18 lbs/inAuxiliary contacts: Torque 7 lbs/in

Ground terminal block:Torque 7 lbs/in

eOT16...32:9-10 mm0,35 - 0,39 ineOT45...63:10 - 12 mm0,39 - 0,47 in

eOT16...32:0,75...10mm2

18...8 AWGeOT45...63:1,5...25 mm2

14...4 AWG

A07

199

Operating handleOperating handle may be padlocked in the OFF-position with up to three padlocks. When locked, the enclosure cover is interlocked and can not be removed. All padlocks must be opened to gain entry to the enclosure.

A00

323A

Ø 5...8 mm / 0.20...0.32 in

A00

323A

Ø 5...8 mm / 0.20...0.32 in

Reinstall enclosure cover, note that both the switch and the operating handle on the cover must be in the OFF-position. Tighten the cover screws.

Ø 5...10 mm / 0.20...0.39 in

Ø 5...10 mm / 0.20...0.39 in

eOT Series Enclosed Manual Motor Controllers

ABB Inc. / USA

16250 W. Glendale DriveNew Berlin, WI 53151

www.abb.com/us

ABB Inc. / CANADA

2117, 32nd AvenueLachine, QC H8T 3J1

www.abb.com/ca

1525,98

501,97

161,46,35

mmin

1405,51

762,99

4,50,18

7,400,29

1003,94

ABB Oy

Piirustus No.Document No.

TekiPrepared

HyväksyiApproved

TarkastiChecked

13*EOT16-32U_P_-S A2279 1648

05-08-03T Rintamäenpää

Low Voltage Products

S07

152

/ M

0008

4 E

OT

16-3

2U_P

_-S

A

ONI

O O

FF

1525,98

Handle OHB 2AJ Knock-outs on top and bottom

3/4 "1/2 "M25

Selector type handle Pistol type handle

R2,250,09

45

126 1,77

4,96

361,42

240,94

250,98

34,5

1,36115,54,55

1,1830

1,1830

200,79

Metric M20(0,79 dia)

Metric M20(0,79 dia)

200,79

190,75

501,97

eOT32U_, eOT45U_ (enclosure size 2)

eOT16_, eOT25_, eOT32_ (enclosure size 1)

eOT63_ (enclosure size 3)

eOT32U_ , eOT45U_ (enclosure size 2)

eOT Series Enclosed Manual Motor Controllers

2108.27 189

7.44

30011.81

2389.37

1505.91

1054.13

Ø6.6 0.26

1817.12

1365.35

451.77

20.50.81

602.36

2389.37

1897.44

1" 1 1/4"

ABB Oy

Piirustus No.Document No.TekiPrepared

HyväksyiApproved

TarkastiChecked

Low Voltage Switches

2011-05-10T Mäkkylä

13/EOT30-100U_P_-P C

M00

141/

EO

T30

-100

U_P

_-P

C

1" 1 1/4"

mmin

200.79