Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Energetic particles and their detection in situ(particle detectors)
Part II
George Gloeckler
University of Michigan, Ann Arbor, MIUniversity of Maryland, College Park, MD
Simple particle detectors
Gas-filled countersGeiger tubeIonization chambersProportional counters
Channeltron
Microchannel Plate
Solid-state detector
Scintillation detector
Gas-filled countersGeiger tube
Thin walled metal tube at ground potential
Pluginsulator
High voltagewire at +V
Ionization chambers and Proportional counters
IonizingParticle
Thin EntranceWindow
LoadResistor Coupling
Capacitor
Collecting Potential V
ToAmplifier
A particle passing through a gas-filled counter will ionize the gas along its path
The applied voltage V between the electrodes will sweep the positive and negative charges toward the respective electrodes causing a charge Q to appear on the capacitor.
The charge Q collected (amplitude of pulse) depends on voltage V
100
102
104
106
108
1010
1012
0 200 400 600 800 1000
Num
ber o
f Ion
s C
olle
cted
Voltage (volts)
I II III
IVRecombination
before collection
Dischargeregion
Region I no pulses producedrecombination of charges takes place before they can drift apart and be collected, and no pulses are produced.
Region II ionization chamber region. loss of ions due to recombination becomes small and the charge collected Q = N•e, where N is the number electron-ion pairs produce by the incident energetic particle.
Region III proportional counter regionQ is increased by a factor of M through gas multiplication. Electrons released in the primary ionization will produce additional ionization and thus add to the total charge. M is independent of the initial ionization at the onset of region IIIAmount of deposited energy is recorded
Region IV Geiger regionQ is completely independent of the initial ionization, but governed by the characteristics of the filling gas and electronics.
Channeltronchannel electron multiplier (CEM)
A simple and compact device that detects ~0.1 to ~ 100 keV ions and electrons
When several kilovolts are applied from one end to the other, a single electron produced at the low potential end will be accelerated down the tube and, at every collision with the tube wall, will produce several secondary electrons that continue that process
CEMs are curved to prevent ion feedback caused by cascading electrons that ionize some of the residual gas inside the device toward the high potential end of the devicesPositive ions are thus prevented from being accelerated toward the low potential input, where they could initiate a new cascade
For a fixed voltage, the gain (106 to > 108) depends on length to diameter ratio which sets the number of secondary electron multiplications
The CEM is a small, curved glass tube, ~1 mm inside diameter and several cm long
Inside surface is treated to have • high resistivity• large secondary electron yield • stability when exposed to air
Microchannel Plate (MCP)
Compact particle or photon detectors with a high signal to noise ratio allowing individual event counting
Low background rates (<1 cm-2 s-1)
Are often used as position sensing devices
As in CEMs, electron multiplication MCPs is produced by voltage bias across a resistive glass tube that generates an electron cascade through secondary electron production
An array of microscopic glass tubes (12 to 25 μm spacing), hexagonally packed and sliced to thin (0.5 to 1.0 mm thick) wafers
Microchannel length to diameter (l/d) ratios range from 40:1 to 80:1
Wafers are treated at high (250-450°C) temperature in a hydrogen atmosphere to produce a resistive coating along the micro channels, and the top and bottom surfaces are metallized
MCP wafers are sliced at a small (8-12°) bias angle relative to the microchannel axis
They are stacked in pairs (Chevron configuration) or in triplets (Z-stack), with adjacent wafers having opposite bias angles to prevent ion feedback
Typical bias voltages are ~1 kV per plate and typical gains are ~1000 per plate.
(a) (b)
Chevron Z-stack
Position sensing anodes
Charge pulses from MCPs may be recorded using
One or more discrete anodes (each with its own preamplifier) to count up to 108
counts/second
Resistive or delay line or wedge and stripanodes provide excellent x-y position resolution at the expense of lower maximum count rates
Solid state detectors (SSDs)Surface barrier, Ion implant and Lithium drift detectors
SSDs are solid-state ionization counters with an electric field is set up within a semiconductor crystal by a voltage applied across opposite faces of the crystal
Particles (or energetic photons) penetrating the crystal produces secondary electrons which, in turn, produce further ionization in the crystal until no electron has enough energy left to ionize the atoms in the crystal any further
The electric field inside the crystal sweeps out the liberated charges, their number being proportional to the energy lost by the primary particle
Advantages of SSDs compared to proportional counters• far more effective in stopping particles, and hence absorbing their energy• measurement of the incident particle energy is more precise (because it takes
on average less energy for the production of an electron-hole pair)
Disadvantages of SSDs compared to proportional counters• their sensitive area is limited both because of crystal size and capacitance that
affects amplifier noise• some of the energy of the primary particle goes into nuclear collisions resulting
in a total energy defect for measuring the energy lost by (low energy) particles
Special properties of semiconductor material required for fabrication of SSDs
• The resistivity of the material must be high enough to support the required electric field without creating an excessive leakage current
• The charge carriers must have a high mobility in the crystal in order to be collected in a reasonably short time
• The trapping rate for the carriers must be low in order to maintain a high efficiency for charge collection and to reduce space-charge buildup within the crystal
• The average energy required to produce an electron-ion pair must be low, in order to give better energy resolution
• The crystal must be uniform and its properties stable over prolonged time periods
For room-temperature operation only silicon can be used for fabrication of SSDs
Production of electron-hole (n-p) pairs in an ideal (intrinsic) semiconductor• Thermal excitation, n = p ≈ 1019exp(–Eg/2kT)
≈ 2•1010 cm-3 at room temperature• Energetic particle passing through the crystal
- loses energy by ionization thus lifting electrons from the valence band or deeper-lying electronic bands to the conduction band or higher-lying unoccupied bands
- the highly excited states quickly ( ~10-12 s) decay until the electrons are near the bottom of the conduction band and the holes are near the top of the valence band
- decay of these highly excited states produces additional electron-hole pairs
• For every 3.6 eV a particle loses in the crystal, one electron-hole pair is produced
Eg≈1eV
• intrinsic silicon cannot be grown at present- even small amounts of impurity atoms
produce energy levels in the forbidden gap and contribute additional charge carriers
- impurity atoms can supply either additional electrons (donor impurities) or additional holes (acceptor impurities)
- both types of impurity may be present in the same crystal at the same time
- donors have energy levels in the forbidden zone near the conduction band, acceptors near the valence band
- the number of free carriers is large because the energy gap between impurity levels and the conduction (valence) band is small
- these extra carriers add significantly to the conductivity of the material.
• Semiconductor material is classified as either n-type or p-type depending on whether it contains more donor or more acceptor impurities
• The crystal behaves like an intrinsic semi-conductor if the number of donors, ND is equal to the number of acceptors, NA
• Making ND ≈ NA by doping or compensating it with the appropriate impurity increases the resistivity of the crystal
• Compensation also increases the number of traps that reduce collection efficiency and carrier lifetime and enhance the buildup of space charge
n- and p-type semiconductors
p-n junction
• When p-type and n-type semiconductors are brought into electrical contact, electrons from the n material diffuse into the p material while the holes diffuse the other way, until a new equilibrium condition is established.
• A depletion region, xo, a region that contains no free carriers, is establish at the interface• The depletion region can be increased (to ~1 mm) by applying a reverse bias across the
junction• The electric field produced by the applied voltage Va (~100 to ~500 volts) pulls out
additional free carriers from the depletion region until a new equilibrium is established
Diffused-Junction, Surface-Barrier and Ion Implant Detectors
• The p-n junction in the diffused-junction detector is formed by diffusing a donor impurity (e.g. phosphorus) to a shallow depth into one face of a high-purity p-type silicon slice- this face becomes heavily doped n+-type
material with a high donor concentration- a p+-n junction can be made by diffusing an
acceptor impurity• A surface-barrier detector is made using
high-resistivity n-type material - One face of the crystal is chemically etched
and then exposed to air (oxygen)- surface states, formed by spontaneous
oxidation, induce a high density of holes to form a very thin p+ layer
• Ion implant detectors are also made from high-resistivity n-type silicon with a very thin p+ layer formed by implantation of ions
• Electrical contacts are made by evaporating gold onto both surfaces.
Lithium-Drifted Detectors
• Lithium compensation is used to obtain depletion depths larger than 1 mm at moderate bias voltages
• Lithium, donor interstitial impurity, is applied by evaporation to one face of a heated (300-500°C) slice p-type silicon
• Lithium ions diffuse into the crystal to a depth of ~0.1 mm, forming a highly doped n+ region
• Reverse-biasing the junction (with the crystal still at a constant high temperature)- lithium ions drift and redistribute themselves so
that the Li+ concentration is exactly equal to the acceptor concentration of the p material
- donor (Li) and acceptor (usually boron) impurities completely compensate each other producing an effective intrinsic region between the p and n+ material.
- drifting is continued until nearly all the p material is compensated for, most of the remaining p layer removed by lapping and finally chemically etched to form a thin surface-barrier p+ layer.
• Nearly windowless lithium-drifted detectors with depletion depths of ~ cm that operated at moderate (20-50 volts) voltages and are more stable against breakdown have been produced
Scintillation Detector
• An energetic particle passing through a scintillator material excites atoms that then emit light as they decay to their ground states
• The light is then converted to an electrical signal that is amplified and recorded• The scintillation material may be a solid, a liquid, or even a gas and the device
converting light into an electrical signal is generally a photomultiplier tube, although in some applications photo-diodes (essentially thin window SSDs) are used
• Solid scintillation detectors (scintillators) have several advantage over gas counters and even solid-state detectors- energetic particles may be stopped in a relatively small volume of the detector
because of the high (electron) density of the detector- the thickness of solid scintillators can be as large as ~10 cm, allowing total energy
measurements of several hundred MeV/nucleon particles- a fast response allows operation at much higher counting rates than is possible for gas
counters
• Their main disadvantages are - complicated light collection and conversion to electrical signals- higher energy (50 to 300 eV compared to 3.6 eV in silicon SSDs) to produce one
photoelectron- use of photomultiplier tubes and high voltages
• The amount of charge Q produced at the photomultiplier tube output given byQ = ΔE(ηωθμ K/Eph)•e
- η is the small fraction of the energy, ΔE, lost by the energetic particle that is converted into light, which is characterized by some spectral distribution with Eph, the average energy of the emitted photons.
- ω is the optical efficiency (number of photons that reach the photocathode)- θ is the probability of ejection of an electron from the photocathode by a photon- μ (< 1) is the efficiency of the photoelectrons reach the first dynode- K is the multiplication factor due to the secondary emission cascade in the
photomultiplier tube- e is the charge of an electron
• Two types of scintillators are used- organic scintillator material consists of aromatic hydrocarbons whose molecules
contain benzene-ring structures along with various nonaromatic substitutions (e.g. anthracene and stilbene crystals)
- inorganic scintillators are crystals of inorganic salts (e.g. alkali halides) containing small amounts of impurities as activators for light emission
• The desirable properties of a good scintillator are - high conversion efficiency η- high transparency to its fluorescent radiation- short decay times for fluorescent radiation- spectral distribution consistent with the responses of available photosensitive devices.
• The dependence of conversion efficiency on particle type is best expressed in terms of the light output per unit energy lost, dL/dE, as a function of the stopping power dE/dx of the particle
• In organic scintillators the reduction of the conversion efficiency for heavy particles is due to the relatively large fraction of non-radiating transitions that occur from states excited by low-energy electrons (δ-rays) produced by the energetic particle
• In the inorganic scintillator, the reduction in conversion efficiency is probably due to a saturation of the activator sites along the track of a heavily ionizing particle