Electron Metal Catalogue 2012

We have been producing

the highest quality

cabinets, racks, consoles and

accessories for over 30 years.

q u a l i t yf lex ib i l i t y

va lue s e r v i c e

QUALITYqual i t y

Electron Metal AIG has been producing the highest quality

cabinets, racks, consoles and accessories for over 30 years.

Our quality policies and procedures go far beyond the

industry standards, ensuring your needs are always met. It

is this commitment to quality that keeps industry leaders in

the telecommunications, networking, broadcast, security

and OEM markets choosing Electron Metal AIG products.

Award winning products with ahistory of excellence.

All products meet or exceed allindustry requirements

Precision manufacturing capabilitiesallowing the tightest specifi cations tobe met and consistently delivered

Only top grade materials used in all of our products

Table Of C

ontents

1

Table of Contents

www.electronmetal.ca 1-866-96-RACKS

Cabinets

Series 4000 Server Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 4000 Server Cabinet Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 4000 Network Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 4000 Network Cabinet Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 4000 Side Venting Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Colocation Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Zone 4 Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accessories for Zone 4 Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Broadcast Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Broadcast Cabinet Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cabinet Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Management for Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 2Page 3Page 4Page 5Page 6Page 7Page 8Page 9Page 10Page 11Page 12Page 13, 14

Relay Racks

Series 710 Relay Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Series 800 Relay Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Zone 4 Relay Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vertical Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Horizontal Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Post Rack Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Post Racks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Post Rack Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 23Page 24Page 25Page 26Page 27Page 28Page 29Page 30

Wall Mounts

Wall Mount Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reverse Wall Mount Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SlimLine Wall Mount Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wall Mount Swing-Out Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wall Mount Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Wall Mount Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 32Page 33Page 34Page 35Page 36Page 37

Shelves and Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 38, 39

LAN Furniture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 44

Consoles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 45

Rollouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 46

Staging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 47

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 52

Technical Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 49 - 51

Custom Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 48

Power Distribution

Electrical and PDU Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PDU Ordering Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 19, 20Page 21

Containment Solutions

Improve Your Data Center’s PUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cold Aisle / Hot Aisle Containment Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hot Air Chimney Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Retrofit Cooling Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 15Page 16Page 17Page 18

Accessories

Security Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilation and Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mounting Rails and Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page 40Page 41Page 42, 43

Ca

bin

ets

Series 4000 Server Cabinets

2

The Series 4000 Server Cabinet line is our latest off ering designed for server housing applications: a scalable enclosure line designed to expand and adapt to your demanding server requirements. Whether you require additional cooling, power, cable management or depth, the Series 4000 line was designed to grow with your requirements, saving you money and downtime.

* Features:

Fully welded 14 ga. Cold Rolled Steel construction with 10 year warranty

Fully assembled and ready to use

24” standard and custom width options

Solid, perforated, louvered, acrylic, split, thermal and custom door options

Solid, perforated, louvered and custom side panel options

Solid top cover with 6 cable / fan cutouts

Hot air chimney / large cable volume top cutout

Wide variety of cable management options

Sizes range from 24 RU to 48 RU

Standard depths of 36” and 42” or custom depths available

2 pairs of 19” adjustable cage nut mounting rails with RU markings

Load capacity of 2000 lbs

Optional power & thermal solutions

Many other accessories available

1-866-96-RACKS www.electronmetal.ca

Part No. Width Depth Height RU

A B C

CB4KSV-212436-BK 24 36 48 24CB4KSV-212442-BK 24 42 48 24CB4KSV-214236-BK 24 36 79.5 42CB4KSV-214242-BK 24 42 79.5 42CB4KSV-214436-BK 24 36 83 44CB4KSV-214442-BK 24 42 83 44CB4KSV-214836-BK 24 36 90 48CB4KSV-214842-BK 24 42 90 48

* Kit Includes:

1 frame 2 pairs mounting rails square holes with RU markings 100 cage nuts Perforated front door with lockable swing handle. Split perforated rear door with lockable swing handle 1 universal accessory channel (for mounting PDUs and/or

cable management) 1 top with chimney cut out and 2 fan cut outs 4 addition top fan cut outs / cable entry points. 1 set of levelling feet 2 side panels with quick release locks

q u a l i t y f lex ib i l i t y va lue s e r v i c e

B

C

A

Chimney cut-out now

standard ensuring future

cooling capacity of up to 20kW!

Dimensions shown in inches

c®

CertifiedElectrical Safety

3www.electronmetal.ca 1-866-96-RACKS

Cabinets

Series 4000 Server Cabinet AccessoriesAccessories

Part No. Width Depth RU DescriptionSHKFST-190114-BK 19 14 1 Keyboard Shelf SHFFMT-190212-BK 19 12 2 Front Mount ShelfSHFFMT-190316-BK 19 16 3 Front Mount ShelfSHFFMT-190318-BK 19 18 3 Front Mount ShelfSHFADJ-190124-BK 19 24-32 1 Frt/RearMt.Adj.DpthSHFADJ-190128-BK 19 28-36 1 Frt/RearMt.Adj.Dpth SHSFRM-190118-BK 19 18 1 Frt/Rear Mnt. SlidingSHSFRM-190124-BK 19 24 1 Frt/Rear Mnt. Sliding

Part No. Description RUCMCUAC-012404-BK Vertical UAC 24CMCUAC-014204-BK Vertical UAC 42CMCUAC-014404-BK Vertical UAC 44CMCUAC-014804-BK Vertical UAC 48

Vertical Universal Accessories Channel (UAC)

Can also be used as a cable manager. Used to support vendor neutral PDU, or tie wrapping cables, or used with D-Ring managers.

Part No. DescriptionCMCLAD-002406-BK Cable Ladder 6 x 42CMCLAD-004206-BK Cable Ladder 6 x 73.5CMCLAD-004406-BK Cable Ladder 6 x 77CMCLAD-004806-BK Cable Ladder 6 x 84CMCLAD-002410-BK Cable Ladder 10 x 42CMCLAD-004210-BK Cable Ladder 10 x 73.5CMCLAD-004410-BK Cable Ladder 10 x 77CMCLAD-004810-BK Cable Ladder 10 x 84CMCALB-002400 Cbl Tie Bar Alum. ¼ x ¾ x 42 c'snkCMCALB-004200 Cbl Tie Bar Alum. ¼x¾ x73.5c'snkCMCALB-004400 Cbl Tie Bar Alum. ¼ x ¾ x 77 c'snkCMCALB-004800 Cbl Tie Bar Alum. ¼ x ¾ x 84 c'snk

Vertical Cable Management

Part No. Width Height DepthEXHCHI-212414-BK 24 24 14

Chimney

Part No. DescriptionFANSTD-061005 Whisper Fan 6" 100CFM grill 5' cordFANSTD-062003 Fan 6" 200 CFM Grill 3' cordFANSTD-062005 Fan 6" 200CFM grill 5' cordFANSS4-041003 4" 100CFM w/Series4000 adaptor 3' cord

Fans

Power Distribution

Power distribution is a critical need to most Rack or Cabinet solutions. Whether you need just standard 15amp power bars or 3 phase 60amp metered and monitored units, Electron Metal AIG can supply the solution for you. We can also pre-install your favorite brand if you prefer. Refer to the PDU section for more details.

Shelves

When assembling your cabinet or rack, certain equipment may not be rack-mountable and will have to be put on a shelf. Electron Metal AIG has a wide array of fixed or sliding shelves, keyboard shelves, drawers and more.

See shelf section for more options

See Cable Management for Cabinets section for more options

Part No. DescriptionCMCREU-020004-BK 4.5" x 2.3" (5 Rings per kit) - black

D-Ring Cable Management Kit for UAC

Custom Heights Available

*Recessed

See Containment section for more options

Part No. DescriptionCMCTPS-240500-BK For 24"W (1 cabinet)CMCTPS-300500-BK For 30"W (1 cabinet)CMCTPS-720500-BK For 72"W (3x 24"W cabinets)CMCTPS-900500-BK For 90"W (3x 30"W cabinets)

Top Cable Partitions

Dividers allow you to create separate pathways for power, fiber or copper communication cables.

Part No. Description BPSFST-190100-BK (19 x 1 RU) Panel Tool-lessBPSFST-190200-BK (19 x 2 RU) Panel Tool-lessBPSFST-190300-BK (19 x 3 RU) Panel Tool-lessBPSFST-190400-BK (19 x 4 RU) Panel Tool-lessBPSFDS-190100-BK (19 x 1 RU) Panel Formed SteelBPSFDS-190200-BK (19 x 2 RU) Panel Formed SteelBPSFDS-190300-BK (19 x 3 RU) Panel Formed SteelBPSFDS-190400-BK (19 x 4 RU) Panel Formed Steel

Blanking Panels

Part No. DescriptionCASSP4-000300-BK Set of 4 Pivoting 3" Casters with Series 4000 Mounting Plates (black) 2000 lbs capacity

Caster Kit

Part No. DescriptionCV4SOL-000036-BK Solid Bottom Floor Plate 36" Deep CV4SOL-000042-BK Solid Bottom Floor Plate 42" Deep CV4CAL-000036-BK 8" x 8" AirLock Brush Kit 36" DeepCV4CAL-000042-BK 8" x 8" AirLock Brush Kit 42" Deep

Bottom Floor Plates

Part No. Width Height RU DepthHCMROV-190003-BK 19 0 0 3 HCMROV-190005-BK 19 0 0 5

HCMSTD-190103-BK 19 1.75 1 3HCMSTD-190203-BK 19 3.5 2 3HCMSTD-190303-BK 19 5.25 3 3HCMSTD-190403-BK 19 7 4 3HCMREC-190103-BK* 19 1.75 1 3HCMREC-190203-BK* 19 3.5 2 3

HCMRET-190103-BK 19 3.25 1 3HCMRET-190204-BK 19 4.125 2 4

Horizontal Cable Management

Part No. Grounding KitsELEGWI-061005-GN 6awg FT4 Grnd. Cable w/Lug - 5ftELEGWI-061010-GN 6awg FT4 Grnd. Cable w/Lug - 10ft

Grounding

Part No. Vertical Copper Ground BarsELEGV2-002400 3/16x1x42 tap 1/4-20 @ 5/8c-c 24 RUELEGV2-004200 3/16x1x73.5 tap 1/4-20 @ 5/8c-c 42 RUELEGV2-004400 3/16x1x77 tap 1/4-20 @ 5/8c-c 44 RUELEGV2-004800 3/16x1x84 tap 1/4-20 @ 5/8c-c 48 RU

Part No. Horizontal Ground BarsELEGH2-190103 Hrz.Grnd.bus 19x1x3/16 tap 1/4-20 @ 5/8c-c

Note: Cage-nut rails required for Tool-less

* Dimensions shown in inches

*

Ca

bin

ets

Series 4000 Network Cabinets

4 1-866-96-RACKS www.electronmetal.ca


A B C

CB4KNW-272430-BK 30 30 48 24CB4KNW-272436-BK 30 36 48 24CB4KNW-272442-BK 30 42 48 24CB4KNW-274230-BK 30 30 79.5 42CB4KNW-274236-BK 30 36 79.5 42CB4KNW-274242-BK 30 42 79.5 42CB4KNW-274430-BK 30 30 83 44 CB4KNW-274436-BK 30 36 83 44CB4KNW-274442-BK 30 42 83 44CB4KNW-274830-BK 30 30 90 48CB4KNW-274836-BK 30 36 90 48CB4KNW-274842-BK 30 42 90 48

The Series 4000 Network Cabinet line was designed for dense cabling applications where good cable management is a requirement. With its extra-wide 30” frame, it has the room required to manage high cable loads and still off er proper airfl ow. As with all Electron Metal AIG Cabinet lines, we have multiple standard options and the ability to tailor this product to meet your exact application.

* Features:



30” and custom width options

Solid, perforated, louvered, acrylic, split and custom door options


Solid top cover with 6 cable entry/fan cutouts

Hot air chimney / large cable volume top cutout


Sizes range from 24 RU to 48 RU. 44 RU is our standard

Depths are 30”, 36” and 42” or custom

2 pairs of 19” adjustable cage nut mounting rails, with cable thrus





B

C

A

Chimney cut-out now standard

ensuring future cooling capacity of

up to 20kW! Also larger opening is

perfect for working with large

quantities of Cat 6A cabling.

* Kit Includes:

1 frame 2 pairs mounting rails square holes with RU markings 100 cage nuts Perforated front door with lockable swing handle Split perforated rear door with lockable swing handle 1 universal accessory channel (for mounting PDUs and/or

cable management) 2 vertical cable managers 1 top with chimney cut out and 2 fan cut outs 4 addition top fan cut outs / cable entry points 1 set of levelling feet 2 side panels with quick release locks


c®

CertifiedElectrical Safety


Cabinets

Series 4000 Network Cabinet AccessoriesAccessories

5


Chimney

Power Distribution


Part No. DescriptionCMCREU-020004-BK 4.5 x 2.3 (5 Rings per kit) - black



Part No. Width Depth RU DescriptionSHKFST-190114-BK 19 14 1 Keyboard Shelf SHFFMT-190212-BK 19 12 2 Front Mount ShelfSHFFMT-190316-BK 19 16 3 Front Mount ShelfSHFFMT-190318-BK 19 18 3 Front Mount ShelfSHFADJ-190124-BK 19 24-32 1 Frt/RearMt.Adj.DpthSHFADJ-190128-BK 19 28-36 1 Frt/RearMt.Adj.Dpth SHSFRM-190118-BK 19 18 1 Frt/Rear Mt. SlidingSHSFRM-190124-BK 19 24 1 Frt/Rear Mt. Sliding

Shelves



Part No. DescriptionCMCLAD-002406-BK Cable Ladder 6 x 42CMCLAD-004206-BK Cable Ladder 6 x 73.5CMCLAD-004406-BK Cable Ladder 6 x 77CMCLAD-004806-BK Cable Ladder 6 x 84CMCLAD-002410-BK Cable Ladder 10 x 42CMCLAD-004210-BK Cable Ladder 10 x 73.5CMCLAD-004410-BK Cable Ladder 10 x 77CMCLAD-004810-BK Cable Ladder 10 x 84CMCBEV-032405-BK (3.25 x 5 x 42) CMCBEV-034205-BK (3.25 x 5 x 73.5) CMCBEV-034405-BK (3.25 x 5 x 77)CMCBEV-034805-BK (3.25 x 5 x 84)


See Cable Management section for more options

*Needs to be ordered with custom made rails

Part No. DescriptionCV4SOL-000030-BK Solid Bottom Floor Plate 30" Deep CV4SOL-000036-BK Solid Bottom Floor Plate 36" Deep CV4SOL-000042-BK Solid Bottom Floor Plate 42" Deep CV4CAL-000036-BK 8 x 8 AirLock Brush Kit 36" DeepCV4CAL-000042-BK 8 x 8 AirLock Brush Kit 42" Deep

Bottom Floor Plates


Caster Kit

Part No. DescriptionCMCTPS-240500-BK For 24"W (1 cabinet)CMCTPS-300500-BK For 30"W (1 cabinet)CMCTPS-720500-BK For 72"W (3 x 24"W cabinets)CMCTPS-900500-BK For 90"W (3 x 30"W cabinets)



Part No. DescriptionALBPMA-020600-BK Brush Kit for Vertical PMA Rails*VENALB-060006-BK Air Locking Brush for 6” Fan cut-out

Air Containment Brushes

Proper airflow is important for cooling systems to work correctly. Ensure Proper airflow with Airlock brushes.




Blanking Panels


Grounding




*Recessed






Fans



*

* Features:

Fully welded 14 ga. Cold Rolled Steel construction with 10 year Warranty

Fully assembled and ready to use (or in 3 pre-assembled pieces if required)

40” standard width with custom width options

Perforated Split or Solid doors depending on thermal cooling strategy

Solid side panels

Optional chimney

10 cable entry points and large Thermal Chimney cut-out

Wide variety of cable management options (High density managers standard)

Size 44 RU, Depth 48”

19” adjustable mounting rails, tapped or Cage nut styles




Buy a kit or customize your own!


A B C

CBSKPD-214448-BK 40 48 83 44

Part No. Description

EXHCHI-212414-BK 40 W x 24H x 14 D Adjust.Height

Ca

bin

ets

Series 4000 Side Venting Cabinets


The Series 4000 Side Venting Cabinet was designed for use with the Cisco 7018 Switch and other side venting IT Equipment. A scalable enclosure line designed to expand and adapt to your demanding network requirements. Whether you require additional cooling (up to 25kW), power, cable management or depth, the Series 4000 line was designed to grow with your requirements, saving you money and downtime.

Standard Confi gurations

Option 1: Perforated front and rear doors for standard hot aisle/cold aisle deployment

Option 2: Perforated front doors and solid rear doors with hot air chimney deploymentExhaust Chimney


C

A

B

Optional cable dividers


Electron Metal AIG is one of Canada’s largest suppliers of Colocation Cabinets. We have earned this business by tailoring products to our customers’ exact needs. We off er robust and secure full, 2, 3, 4 and 8 section Cabinet solutions at aff ordable prices.

* Features:

Available with up to 8 separate sections, fully welded 14 ga. Cold Rolled Steel construction


24”, 30” and custom width options

Unique key, padlockable latch, combination, electronic lock options

Solid, perforated, louvered and custom side panels and top cover options


Sizes range from 42 RU to 52 RU, Depths of 36” thru 48”

19” adjustable mounting rails, tapped or cage nut styles




Part No. Width Depth Height RU Sections

A B C

CBC1KT-214442-BK 24 42 83 44 1CBC2KT-214442-BK 24 42 83 44 2CBC4KT-214442-BK 24 42 83 44 4CBC8KT-214442-BK 24 42 83 44 8

Power Distribution



Grounding


Accessories

Standard 2 Section Colo Cabinet front and rear lockable doors, solid side panels, 4 pairs of RU marked rails, section divider, two secure cable channels and levelling feet


Colocation Cabinets C

abinets


B

C

A

Cable Channels allow for

secure cable routing to each

section of the cabinet.

7


Ca

bin

ets

Zone 4 Cabinets


Electron Metal AIG off ers a selection of Seismic Zone 4 rated Cabinets. These robust solutions have all passed the Bellcore GR-63-CORE standards for Zone 4 applications. We have invested in the design, testing and certifi cation to ensure our customers get what they pay for. Ensure your Zone 4 solutions pass the requirement for static defl ection and vibration resistance tests by going with Electron Metal AIG.

* Features:

Fully welded 14 ga. heavy-duty Cold Rolled Steel construction


26” and 30” wide options

Solid, perforated, louvered, acrylic, split, thermal and custom door

options

Solid top cover with 4 fan cut-outs / cable entry points

UAC cable management

Certifi ed sizes of 42, 44 & 47 RU

Depths of 30” thru 42”

Certifi ed rails with cable cut-outs



Zone 4 Earthquake Environment GR-63-CORE certifi ed

4.4 Earthquake, Offi ce Vibration and Transportation Vibration

4.4.1 Earthquake Environment and Criteria

R4-68 Permanent structural or mechanical damage - Compliant

R4-69 Defl ection not to exceed 3 inches - Compliant

R4-70 Natural Mechanical Frequency greater than 2.0 Hz - Compliant

04-71 Natural Mechanical Frequency greater than 6.0 Hz - Compliant

04-74 Framework should be of welded construction - Compliant

R4-75 Base mounting without auxiliary support - Compliant

04-76 Static Pull - Compliant

R4-77 Expansion anchor depth - Compliant

04-78 Expansion anchors suitable for dynamic applications - Compliant

04-79 Expansion anchors of steel construction - Compliant


A B C

CBZKI2-234230-BK 30 30 79.5 42CBZKI2-234430-BK 30 30 83 44CBZKI2-234730-BK 30 30 88.25 47CBZKI2-234236-BK 30 36 79.5 42CBZKI2-234436-BK 30 36 83 44CBZKI2-234736-BK 30 36 88.25 47CBZKI2-234242-BK 30 42 79.5 42CBZKI2-234442-BK 30 42 83 44CBZKI2-234742-BK 30 42 88.25 47

B

C

A

* Kit Includes:

1 frame 30 x 83 x 83 1 set of levelling feet neoprene base 2 pairs 19” mounting rails (4.7”) cage-nuts cut-outs RU markings 100 cage-nuts 1 universal accessory channel 1 x 4.75 1 front door perforated 3 pt swing-handle with lock 1 rear door perforated 3 pt swing-handle with lock 2 solid side panels 1 top cover with 4 fan cut-outs

Zone 4 Certifi ed



Cabinets

Cabinet AccessoriesAccessories

9


Chimney

Power Distribution





Part No. Width Depth RU DescriptionSHKFST-190114-BK 19 14 1 Keyboard Shelf SHFFMT-190212-BK 19 12 2 Front Mount ShelfSHFFMT-190316-BK 19 16 3 Front Mount ShelfSHFFMT-190318-BK 19 18 3 Front Mount ShelfSHFADJ-190124-BK 19 24-32 1 Frt/RearMt.Adj.DpthSHFADJ-190128-BK 19 28-36 1 Frt/RearMt.Adj.Dpth SHSFRM-190118-BK 19 18 1 Frt/Rear Mt. SlidingSHSFRM-190124-BK 19 24 1 Frt/Rear Mt. Sliding

Shelves



Part No. DescriptionCMCLAD-002406-BK Cable Ladder 6 x 42CMCLAD-004206-BK Cable Ladder 6 x 73.5CMCLAD-004406-BK Cable Ladder 6 x 77CMCLAD-004806-BK Cable Ladder 6 x 84CMCLAD-002410-BK Cable Ladder 10 x 42CMCLAD-004210-BK Cable Ladder 10 x 73.5CMCLAD-004410-BK Cable Ladder 10 x 77CMCLAD-004810-BK Cable Ladder 10 x 84CMCBEV-032405-BK (3.25 x 5 x 42) CMCBEV-034205-BK (3.25 x 5 x 73.5) CMCBEV-034405-BK (3.25 x 5 x 77)CMCBEV-034805-BK (3.25 x 5 x 84)



Part No. DescriptionCV4SOL-000030-BK Solid Bottom Floor Plate 30" Deep CV4SOL-000036-BK Solid Bottom Floor Plate 36" Deep CV4SOL-000042-BK Solid Bottom Floor Plate 42" Deep CV4CAL-000036-BK 8" x 8" AirLock Brush Kit 36" DeepCV4CAL-000042-BK 8" x 8" AirLock Brush Kit 42" Deep

Bottom Floor Plates


Caster Kit




Part No. DescriptionALBPMA-020600-BK Brush Kit for Vertical PMA RailsVENALB-060006-BK Air Locking Brush for 6” Fan cut-out





Can also be used as a cable manager. Used to support vendor neutral PDU, or tie wraping cables, or used with D-Ring managers.


Grounding




Blanking Panels


*Recessed






Fans


Please note that only the Zone 4 Cabinets and Frames have been Zone 4 tested and certifi ed. All cabinet accessories are not Zone 4 certifi ed.


*

Electron Metal AIG has been providing tailored Cabinets and Racks to Canada’s top broadcasting companies for over 20 years. Broadcast Industry requirements can diff er greatly from the Telco industry and the standard 24”W x 42 RU Server Cabinets so commonly deployed in IT applications. Again, it is Electron Metal AIG’s diverse and fl exible manufacturing capabilities that keep our Broadcast customers coming back time and time again. This fl exibility combined with our great customer service and competitive pricing makes Electron Metal AIG the obvious choice for Facilities and Purchasing management.

Broadcast CabinetsC

ab

ine

ts



* Broadcast Cabinet Kit Includes:

1 Series 2000 frame 22” W (other widths also available)

2 pairs mounting rails tapped 10-32

1 UAC channel

3 aluminum tie bars

1 perforated rear door with slam latch

1 perforated top cover

2 side panels


A B C

CBBKIT-192430-BK 22 30 48 24CBBKIT-194430-BK 22 30 83 44CBBKIT-194630-BK 22 30 86.5 46CBBKIT-192436-BK 22 36 48 24CBBKIT-194436-BK 22 36 83 44CBBKIT-194636-BK 22 36 86.5 46

* Features:



22” standard and custom width options

Solid, perforated, louvered, acrylic, split, thermal and custom door options


Open top or many cover options


Sizes range from 24 RU to 48 RU

Customizable depths options

2 pairs of 19” adjustable cage nut mounting rails with RU markings







Cabinets

Broadcast Cabinet AccessoriesAccessories

Part No. Width Depth RU DescriptionSHKFST-190114-BK 19 14 1 Keyboard Shelf SHFFMT-190212-BK 19 12 2 Front Mount ShelfSHFFMT-190316 -BK 19 16 3 Front Mount ShelfSHFFMT-190318-BK 19 18 3 Front Mount ShelfSHFADJ-190124-BK 19 24-32 1 Frt/RearMt.Adj.DpthSHFADJ-190128-BK 19 28-36 1 Frt/RearMt.Adj.Dpth SHSFRM-190118-BK 19 18 1 Frt/Rear Mnt. SlidingSHSFRM-190124-BK 19 24 1 Frt/Rear Mnt. Sliding




Part No. DescriptionCMCLAD-002406-BK Cable Ladder 6 x 42CMCLAD-004206-BK Cable Ladder 6 x 73.5CMCLAD-004406-BK Cable Ladder 6 x 77CMCLAD-004806-BK Cable Ladder 6 x 84CMCLAD-002410-BK Cable Ladder 10 x 42CMCLAD-004210-BK Cable Ladder 10 x 73.5CMCLAD-004410-BK Cable Ladder 10 x 77CMCLAD-004810-BK Cable Ladder 10 x 84CMCALB-002400 Cbl Tie Bar Alum. ¼ x ¾ x 42 c'snkCMCALB-004200 Cbl Tie Bar Alum. ¼x¾ x73.5c'snkCMCALB-004400 Cbl Tie Bar Alum. ¼ x ¾ x 77 c'snkCMCALB-004800 Cbl Tie Bar Alum. ¼ x ¾ x 84 c'snk


Power Distribution


Shelves




Part No. DescriptionCMCREU-020004-BK 4.5" x 2.3" (5 Rings per kit) - black


Part No. DescriptionCASSTC-190300-BK Set of 3” casters (2 with brake) with (19”) channels

Caster Kit


Grounding




Blanking Panels


*Recessed






*

Cabinet Ordering Guide

Side

Panels

None One Two Tool-less Solid Perforated Louvered Locking Custom

Vertical Tie Bar

Floor Open Closed Castors Cable Entry

Horizontal Cable Management Open Ring Flip Door 3.5”Flip Door 5.25”Double Sided

Cable Manager w/ door

Cable Ladder

Cable U Channel

Universal Accessories Channel

Vertical Cable Retainer

Vertical Cable

Management

Color

Black Grey White Custom

Notes

Mounting Angles ( PMA`s ) Cage nuts Drilled & Tapped With Cable Through

With Cable Through & Containment Brushes

Back Door Acrylic (Viewing) Solid Perforated Louvered Custom Split

Front Door Acrylic (Viewing) Solid Perforated Louvered Custom Split

Roof Solid4 Fan cut-out Perforated Louvered Cable Entry Custom

19”23”

Mounting Width

Overall Height: Overall Width: Depth: 48”(1219mm) 24 RU 24”(610mm) 30”(763mm) 80”(2032mm) 42 RU 26”(660mm) 36”(914mm) 83”(2108mm) 44 RU 30”(762mm) 42”(1066mm) 90”(2286mm) 48 RU 40” Side Venting 48”(1219mm) Other ________ Other_______ Other _______

Frame Size

2 U3 U4 U

Company Name Job Name

City Province

Contact Name Product Required Date

Phone Email

Cable Entry w/ Containment

Fiber Tray1 U

Qty ____

Qty ____

Quantity of

Cabinets

Required ________

Shelves Front Mount 3 RU Front & Rear Mount 1 RU Keyboard/Monitor 7 RU Heavy Duty (May Increase RU)

Front Mount Sliding 3 RU Front & Rear Mount Sliding 1 RU Vented

Qty ____

Depth ____

PDUs Basic Metered Monitored Switched

Vertical Horizontal

Qty ____

____ # of Outlets ____ Type of Outlet ____ Cord End Type____ Length of Cord

Grounding 5 ft Grounding Cable w/ Lug Horizontal Bus Bar 10 ft Grounding Cable w/ Lug

Roof Containment brush kits for cable entry points

Adjustable Height Chimney

(Roofs include 6 cable entry/fan cutouts with large chimney plate)

Casters Pivoting 3” Casters

(1 UAC is included)

- Qty ____

- Required Height ____


Ca

bin

ets


Cable Management for Cabinets

www.electronmetal.ca 1-866-96-RACKS 13

Cabinets

Part No. Height RU DepthCMCSTD-022404-BK 42 24 4.5 CMCSTD-024204-BK 73.5 42 4.5 CMCSTD-024404-BK 77 44 4.5 CMCSTD-024804-BK 84 48 4.5

Vertical Cable Management Trough

This is the same trough that is used in our Cable Management Cabinet Kit. Oblong holes along the front provide access to cable from side, while holes on rear match holes in our Cable Management PMA’s. Hinged front door provides easy access to your cables. Also available in a shorter depth for tighter areas. Dimensions are 2.5”W x 6”D or 2.5”W x 4.5”D for shorter model.

Short model

Part No. Height RU DepthCMCSTD-022406-BK 42 24 6 CMCSTD-024206-BK 73.5 42 6 CMCSTD-024406-BK 77 44 6 CMCSTD-024806-BK 84 48 6

Standard model

Part No. Height RU DepthCMCUSL-022404-BK 42 24 4 CMCUSL-024004-BK 70 40 4 CMCUSL-024404-BK 77 44 4 CMCUSL-024804-BK 84 48 4

Vertical Cable “U” Channel Slip-On Bolts

The “U” channel is a simple method of cable management. It consists of a 2” x 4” channel, with a series of easy slip-on bolts to help you route your cables.

Part No. Height RU DepthCMCLAD-002406-BK 42 24 6 CMCLAD-004206-BK 70 42 6 CMCLAD-004406-BK 77 44 6 CMCLAD-004806-BK 84 48 6 CMCLAD-002410-BK 42 24 10 CMCLAD-004210-BK 70 42 10 CMCLAD-004410-BK 77 44 10 CMCLAD-004810-BK 84 48 10

Vertical Cable Ladder

The cable ladder is perfect for situations where a lower profile cable management solution is required. At 6” or 10“ wide, but only ½” deep, these ladders use up a minimum of space within the cabinet. Cutouts along the front provide easy routing of cables, while small holes offer space to install tie-wraps. A small lip on each side keeps the entire assembly rigid.

Part No. (Aluminum) Height RUCMCALB-002400 42 24CMCALB-004200 73.5 42CMCALB-004400 77 44CMCALB-004800 84 48

Vertical Cable Tie Bar

These cable tie bars are used to sort your cables verticallythroughout the cabinet. Made from 1/4” x 3/4” aluminum.

Part No. Height RU DepthCMCRET-032405-BK 42 24 5 CMCRET-034205-BK 73.5 42 5 CMCRET-034405-BK 77 44 5 CMCRET-034805-BK 84 48 5

Vertical Cable Retainer

This item is for situations that require quick and simple cable management. With no tie-wraps or bolts to adjust, you can easily slip your cables in and out of the retainers when needed. Retainers are 5”W x 2.5”D and mountedon a 1 ¼” x 3/8” flat bar.

Electron Metal AIG offers many options for managing cables within our cabinets. Choose from simple cable tie bars to cable troughs for more complex cabling. Each one is simple to use. There is a solution for every project!

NO. DESCRIPTION

1 VERTICAL CABLE RETAINER 3 x 5 x (70)

2 VERTICAL UAC WITH D-RINGS

3 U CHANNEL SLIP-ON BOLTS 2 x 4 x (77)

4 VERTICAL CABLE MGT SLOPED 3.25 x 5 x (77)

5 VERTICAL CABLE MGT 2.5 x 4.5 x (77)

6 CABLE LADDER 6"

7 VERTICAL ALUMINUM TIE BAR

Part No. RUCMCUAC-012404-BK 24CMCUAC-014204-BK 42CMCUAC-014404-BK 44CMCUAC-014804-BK 48





Part No. Width Height RU DepthCMCBEV-032405-BK 3.25 47.75 24 5CMCBEV-034205-BK 3.25 73.25 42 5CMCBEV-034405-BK 3.25 76.75 44 5CMCBEV-034805-BK 3.25 83.75 48 5

Bevelled Cable Management

Vertical cable managers with a magnetic door protect your cabling and offer a clean look.


*

Cable Management for Cabinets


Ca

bin

ets

Part No. Height RU DepthCMCHDP-002407-BK 42 24 7CMCHDP-004207-BK 73.5 42 7CMCHDP-004407-BK 77 44 7CMCHDP-004807-BK 84 48 7

Rail Mounted High Density Cable Management

This finger style cable management is secured to the mounting rails, together forming a cablemanagement system optimized for space and functionality. Each finger has PVC radius control insertsto protect cables against damage. Ideal for fibre and / or exceptionally large cabling installations.

NO. DESCRIPTION

1 HORIZONTAL CABLE MANAGEMENT

2 HORIZONTAL CABLE RETAINER

3 CABLE SUPPORT ROD WITH VELCRO

4 HIGH DENSITY HORIZONTAL CABLE MGT

5 HIGH DENSITY CABLE TRAY

6 SOLID CABLE PARTITION

7 CABLE PARTITION WITH CUTOUT

New!

Part No. Width Height RU Depth HCMROV-190003 19 0 0 3 HCMROV-190005 19 0 0 5

Cable Support Rod with Velcro Tie Wrap

New zero RU horizontal managers with velcro tie wraps.

Part No. Width Height RU Depth HCMSTD-190103-BK 19 3 1 3 HCMSTD-190203-BK 19 3 2 3HCMSTD-190303-BK 19 3 3 3HCMSTD-190403-BK 19 3 4 3


Our standard managers with flip lid.

Part No. Width Height RU Depth HCMREC-190103-BK 19 3 1 3HCMREC-190203-BK 19 3 2 3

Recessed Horizontal Cable Management

Part No. Width Height RU Depth HCMH1S-190105-BK 19 1.75 1 5HCMH1S-190205-BK 19 3.5 2 5

High Density Horizontal Cable Management


Solid Cable Partition


Part No. DescriptionCMCTPP-240500-BK For 24"W (1 cabinet)CMCTPP-300500-BK For 30"W (1 cabinet)CMCTPP-720500-BK For 72"W (3x 24"W cabinets)CMCTPP-900500-BK For 90"W (3x 30"W cabinets)

Cable Partition with Cutout

Part No. Width Height RUHCMRET-190103-BK 19 1.75 1HCMRET-190204-BK 19 3.50 2HCMRET-230103-BK 23 1.75 1 HCMRET-230204-BK 23 3.50 2

Horizontal Cable Retainer

This unit makes your cable management projects quick and simple. A series of small steel “fingers” make routing cables easy. Rear panel is made from 14 ga. steel.

1

2

3

4

7

6

5

Part No. Width Depth RU HCMHTY-190204-BK 19 4.6 2

High Density Cable Tray


*

Computer Loads

Cooling PlantCRAH or CRACS

UPS

Computer Loads

Cooling PlantCRAH or CRACS

UPS

Cooling Plant 20 % $26,280.00CRAH or CRACS 17 % $22,338.00UPS 12 % $15,768.00Electrical Distribution 3 % $3,942.00 Lighting 1 % $1,314.00Misc 1 % $1,314.00Computer Loads 46 %

Annual Electrical Costs

Cooling Plant 20 % $26,280.00CRAH or CRACS 8 % $10,512.00UPS 4 % $5,256.00Electrical Distribution 3 % $3,942.00 Lighting 1 % $1,314.00Misc 1 % $1,314.00Computer Loads 63 %

Annual Electrical Costs

Annual Savings: $22,338.00

Based on a 150 kW facility - average electrical cost of 10 cents per kW/h

Improve Your Data Center’s PUE

Before Power and Cooling Optimization

After Power and Cooling Optimization

PUE stands for Power Use Eff ectiveness. It is a measure of Data Center Effi ciency. Your Data Center’s PUE is taken by dividing your total facility power by your IT power – the power consumed by your computer loads. If your company’s Data Center uses 150kW/h of electricity to operate 50kW/h of computer loads, then your PUE would be 3. Electron Metal AIG can improve your Data Center’s PUE by enhancing your cooling system’s performance. Implementing Electron Metal AIG’s Thermal Containment Solutions is a proven way to safely get more capacity out of your data center, while spending less on electricity.

Containm

ent


Hot aisle and cold aisle deployment layouts for Data Center cooling have been a common practice for years. However, with today’s increased heat loads this layout scheme has become diffi cult to manage and can end up being tremendously ineffi cient. Today’s mechanical experts are strongly recommending air containment rooms or systems to help isolate hot air from cold air, dramatically increasing cooling effi ciencies. Electron Metal AIG can off er solutions for either Hot Air or Cold Air containment systems.

Increase cooling effi ciencies by up to 40%!

Reduce hot spots and increase cooling effi ciencies with air containment systems.

Cold Aisle Illustration Hot Aisle Illustration

Sliding Containment Doors Polycarbonate

Containment Tops

Part No. Aisle RU

ACDKLN-004436-BK 36 44 ACDKLN-004448-BK 48 44

Clear Polycarbonate Containment Doors

Electron Metal AIG off ers sliding containment doors for 3’ and 4’ aisles. Custom sizes and hinged doors are also available.

Clear Polycarbonate Tops

Easy to install and allow existing lighting to be utilized.

Part No. Width Depth

ACTKLN-240036-BK 24 36ACTKLN-240048-BK 24 48ACTKLN-300036-BK 30 36ACTKLN-300048-BK 30 48

CONTAINMENT

Cont

Clear Polyca

Easy to instautilized.

Part No.

Con

tain

men

t




Hot Air Chimney Solutions

Containment Exhaust Chimney

Part No. Width Height Depth

EXHCHI-212414-BK 24 24 14EXHCHI-272414-BK 30 24 14EXHCHI-372414-BK 40 24 14


Containm

ent


Active chimneys with fans or

blowers also available!

One of the most cost eff ective and practical ways to increase cooling effi ciencies is with passive hot air chimneys. All 4000 series cabinets from Electron Metal AIG come standard with tops with chimney cut outs so that you can deploy with chimneys immediately or add when your heat loads increase. We also off er active chimneys if you have excessive heat loads that exceed a passive system’s abilities.

Chimneys

Standard sizes listed below but any heights can be off ered. Please call for pricing if you require taller chimneys.

Part No. DescriptionCV4SOL-000030-BK Solid Bottom Floor Plate 30" Deep CV4SOL-000036-BK Solid Bottom Floor Plate 36" Deep CV4SOL-000042-BK Solid Bottom Floor Plate 42" Deep CV4CAL-000036-BK 8" x 8" AirLock Brush Kit 36" DeepCV4CAL-000042-BK 8" x 8" AirLock Brush Kit 42" Deep

Part No. DescriptionALBPMA-020600-BK Brush Kit for Vertical PMA RailsVENALB-060006-BK Air Locking Brush for 6” Fan cut-out



Bottom Floor Plates

Cabinets come standard with open bottoms. Control airflow better with floor plates.

Illustration of raised fl oor and hot air return plenum (raised fl oor is not required for all deployments).


Electron Metal AIG’s ThermEX Extensions were designed for managing high heat density applications. This system allows you to add up to 20kW of heat exhaust to existing cabinets of almost any make! The extensions exhaust heat up towards the ceiling or into your air plenum. Fully tested in some of today’s most demanding applications Electron Metal AIG’s ThermEX Extensions off er one of the most cost eff ective cooling solutions on the market today.

* Features:

Can exhaust 10 – 20kW of heat

No need for additional air conditioning

Change to can be added to almost any brand of cabinet

Saves the need for removing critical equipment thus preventing downtime

Get rid of your hot spots without additional air conditioning!

Retrofi t solutions for 10 - 20kW of heat!


CONTAINMENT

Co

nta

inm

en

t

Part No. Height Width RU Depth Qty Fans Total CFM

TEX432-214406-BK 83 24 44 6 3 600TEX433-214406-BK 83 24 44 6 3 900TEX462-214406-BK 83 24 44 6 6 1200TEX463-214406-BK 83 24 44 6 6 1800TEX442-274406-BK 83 30 44 6 4 800TEX443-274406-BK 83 30 44 6 4 1200TEX482-274406-BK 83 30 44 6 8 1600TEX433-274406-BK 83 30 44 6 8 2400

ThermEX Extensions

Other sizes availableDimensions shown in inches


Power distribution is a critical need for most Rack or Cabinet solutions. Whether you need just standard 15amp power bars or 3 phase 60amp metered and monitored units, Electron Metal AIG can supply the solution for you. We can also pre-install your favorite brand if you prefer. For more information please visit our Website at www.electronmetal.ca or call us at 1-866-96-RACKS.

* Electrical & PDU Options:

Basic Horizontal or Vertical 15A or 20A power bars

Standard, isolated ground or surge suppressed

Metered Single Phase & 3 Phase PDUs

SNMP enabled remote monitored or controlled PDUs

Transfer Switches

Single Phase & 3 Phase UPS Systems

Optional installation


Power Distribution Power D

istribution

Pow

er D

istr

ibut

ion


Power Distribution

Power Distribution is an important part of any size Cabinet or Rack rollout. Listed above are the basic horizontal and vertical PDUs Electron Metal AIG off ers from stock. On the next page is our PDU Ordering Guide which can be used for ordering any other type of PDU including metered, monitored and switched PDUs. Electron Metal AIG can also supply Transfer Switches and UPS Systems if your application requires it. Any of these options can be pre-installed in your next Cabinet order if you wish at no additional charge. For more information or pricing, please call us at 1-866-96-RACKS.

Part No. Qty Input Input Recept. Recept. Recept. Surge Cord Orientation Inputs Volts Amps Type Qty Amps Type Breaker Protected Switch Length Length RU MountingPWBNRS-1506011906-BK Rackmount, rear outlets 1 120 15 5-15P 6 15 5-15R Yes No No 6’ 19” 1 DirectPWBNRS-1506011915-BK Rackmount, rear outlets 1 120 15 5-15P 6 15 5-15R Yes No No 15’ 19” 1 DirectPWBNRS-2006011906-BK Rackmount, rear outlets 1 120 20 5-20P 6 20 5-20R Yes No No 6’ 19” 1 DirectPWBNRS-2006011915-BK Rackmount, rear outlets 1 120 20 5-20P 6 20 5-20R Yes No No 15 ’ 19” 1 DirectPWBNRT-1506011906-BK Rackmount, rear outlets 1 120 15 L5-15P 6 15 5-15R Yes No No 6’ 19” 1 DirectPWBNRT-1506011915-BK Rackmount, rear outlets 1 120 15 L5-15P 6 15 5-15R Yes No No 15 ‘ 19” 1 DirectPWBNRT-2006011906-BK Rackmount, rear outlets 1 120 20 L5-20P 6 20 5-20R Yes No No 6’ 19” 1 DirectPWBNRT-2006011915-BK Rackmount, rear outlets 1 120 20 L5-20P 6 20 5-20R Yes No No 15 ‘ 19” 1 Direct PWBLBS-2S12011912-BK Rackmount, 12 rear, 2 front outlets 1 120 20 5-20P 12 15 5-15R Yes Yes Yes 12 ‘ 19” 1 Direct PWBLFT-2010011912-BK Rackmount, front outlets 1 120 20 L5-20P 10 20 5-20R Yes No No 12 ‘ 19” 1 Direct PWBLRS-201001912-BK Rackmount, front outlets 1 120 20 5-20P 10 20 5-20R Yes No No 12 ‘ 19” 1 Direct

Rackmount PDU, Basic

Part No. Qty Input Input Recept. Recept. Recept. Surge Cord Orientation Inputs Volts Amps Type Qty Amps Type Breaker Protected Switch Length Length RU MountingPWBNVS-151207506-BK Vertical 1 120 15 5-15P 12 15 5-15R Yes No No 6’ 75” 44 DirectPWBNVS-151207515-BK Vertical 1 120 15 5-15P 12 15 5-15R Yes No No 15’ 75” 44 DirectPWBNVS-151408406-BK Vertical 1 120 15 5-15P 14 15 5-15R Yes No No 6’ 84” 48 DirectPWBNVT-151207506-BK Vertical 1 120 15 L5-15P 12 15 5-15R Yes No No 6’ 75” 44 DirectPWBNVT-151207515-BK Vertical 1 120 15 L5-15P 12 15 5-15R Yes No No 15’ 75” 44 DirectPWBNVT-151408406-BK Vertical 1 120 15 L5-15P 14 15 5-15R Yes No No 6 ‘ 84” 48 DirectPWBNVT-201207606-BK Vertical 1 120 20 L5-20P 12 20 5-20R Yes No No 6’ 76” 44 DirectPWBNVT-201207615-BK Vertical 1 120 20 L5-20P 12 20 5-20R Yes No No 15 ‘ 76” 44 DirectPWBNVT-201408506-BK Vertical 1 120 20 L5-20P 14 20 5-20R Yes No No 6 ‘ 85” 44 DirectPWBNVT-201408515-BK Vertical 1 120 20 L5-20P 14 20 5-20R Yes No No 15 ‘ 85” 44 Direct PDUVNN-23101T24CN Vertical 1 208 30 L6-30P 24 20 C-13 Yes No No 10 ‘ 66.25” 44 UACPDUVNN-12102S202N Vertical 2 120 20 5-20P 20 20 5-20R Yes No No 10 ‘ 66.25” 44 UACPDUVNS-12101S102N Vertical 1 120 20 5-20P 10 20 5-20R Yes No Yes 10 ‘ 38.5” 44 UACPWBLFT-32C16021912-BK Vertical 1 208 30 L6-30P 24 20 C-13 Yes No No 10 ‘ 48” 44 UACPWBLVS-151603010-BK Vertical 1 120 15 5-15P 10 20 5-15R Yes No No 10 ‘ 30” 44 UACPA-PWBLVT-202404810-BK Vertical 1 120 20 L5-20P 24 20 5-20R Yes No No 10‘ 48” 44 UAC

Vertical PDU, Basic

Notes

Input Cord

________KVA _____ AMPS ______ Input Connector _______Input Cord Length

Quantity and Type of Output Receptacles____________________________________

Meter

Input Plug

Receptacles

NEMA

5-15R120V

NEMANEMA

L6-20P 208V

NEMA

L5-20P120V

NEMA

L5-30P 120V

5-20P120V

NEMA NEMA

L6-30P 208V

L15-20P208VDelta

NEMA

L15-30P208VDelta

NEMA NEMA

L21-20P120/208V

WYE

NEMA

L21-30P120/208V

WYE

NEMA OTHER

5-15R120V

CS8365C208VDelta

NEMA

5-20R120V

IEC

C13208V

IEC

C19208V

NEMA

L6-20R208V

NEMA

L6-30R 208V

OUTPUT RECEPTACLE TYPES

INPUT RECEPTACLE TYPES

SNMP Connection

PDU Types

Basic – Vertical or horizontal power strip with no meter/monitoring features. Sometimes referred to as a “Dumb PDU”

Metered – Vertical or horizontal power strip that monitors and reports (typically on LED screen) the electrical load or power utilization of the unit or any branch circuit

Monitored – Vertical or horizontal power strip that allows the user to securely view the status of each circuit on their networkor via the Internet. (Typically done via an SNMP Card)

Switched – Vertical or horizontal PDU with the same ability as the Monitored unit but with the added ability to control

Managed – Vertical or horizontal PDU with all the same ability as the Monitored and Switched units plus the ability to meter each individual receptacle

Ver cal PDU Length of unit____________ 19” Rack Mount Horizontal PDU

Single Phase 120 208 3 Phase 208


City Province


Phone Email

Quantity of PDUs Required ________

120 / 208


Power D

istribution

PDU Ordering Guide

RELAY RACKSR

ela

y R

ac

ks


Relay R

acks


Series 710 Relay Rack

This heavy duty rack is perfect for installations that require minimum space and maximum versatility. Our Series 710 relay racks come fully assembled and are available in many diff erent sizes for your specifi c needs. A full line of cable management and accessories is available for this heavy duty Relay Rack line.

* The Series 710 Relay Rack Features:

Fully welded frame made from 12 ga. steel is ready to use

Base plates are made from ¼” thick, 3 ½” x 5” steel angles

Rack is designed to be bolted to the fl oor

Holes tapped 10-32 at standard EIA spacing on front or both front and

rear of the uprights

Sides of rack feature holes to mount cable management accessories or

to gang racks together

Also available for 23” rackmount

Many sizes available

Part No. Description Height RU

A

RK1FR1-192400-BK Tapped 1 side 47.6 24RK1FR2-192400-BK Tapped 2 sides 47.6 24RK1FR1-194400-BK Tapped 1 side 82.6 44RK1FR2-194400-BK Tapped 2 sides 89.6 44RK1FR1-194800-BK Tapped 1 side 89.6 48RK1FR2-194800-BK Tapped 2 sides 89.6 48

A

20 1/2"

13"



* The Series 800 Relay Rack Features:

§ Fully welded frame made from 12 ga. steel is ready to use

§ oor

§ Base can easily be equipped with casters

§ Holes tapped 10-32 at standard E.I.A. spacing on front or both front and rear of the uprights

§ Sides are equipped with holes for cable management or to gang racks together

§ Rack is available in many sizes

§ Side cable management optional

§ Also available for 23” rackmount

The Series 800 relay rack is for installations that do not permit bolting the rack to the oor. It has a large, free standing base that can even be mounted on casters for easy

mobility. Includes pre-drilled and tapped uprights and comes fully assembled.

Series 800 Relay Rack


Part No. Description Height RU ARK8FR1-192600-BK Tapped 1 side 45.5 26 RK8FR2-192600-BK Tapped 2 sides 45.5 26RK8FR1-194600-BK Tapped 1 side 80.5 46 RK8FR2-194600-BK Tapped 2 sides 80.5 46RK8FR1-195000-BK Tapped 1 side 87.5 50RK8FR2-195000-BK Tapped 2 sides 87.5 50

A20 1/2"

24 1/2"

Rela

y Ra

cks



Relay R

acks

Zone 4 Relay Rack


Tested and certifi ed BELLCORE GR-63-CORE Compliant

Ultra-heavy duty reinforced construction

* The Zone 4 Relay Rack features:

Ultra-heavy duty welded 11 ga. steel construction

Heavy duty 6 ½” x 3” side channels for maximum rigidity

Extra welds provide superior strength

Large, bolt down base

Mounting holes tapped 10-32 at standard EIA spacing

Rack accepts cable management accessories

Available in 19” or 23” rackmount sizes

Our Zone 4 relay rack is one of the most cost eff ective solutions available today. Designed for maximum durability and resistance to earthquakes or other vibrations, this rack is BELLCORE

GR-63-CORE TESTED AND CERTIFIED COMPLIANT. The rack features extra-heavy duty construction that will protect your expensive equipment from damage during a seismic event.

Part No. Description Width Height RU

A

RKZFR2-194400-BK 19” rackmount, Tapped 2 sides 24 84 1/16 44RKZFR2-234400-BK 23” rackmount,Tapped 2 sides 28 84 1/16 44

A

18 1/2"

84 1/16"



Vertical Cable ManagementElectron Metal AIG off ers many diff erent cable management solutions for our relay racks. You can choose from our various side mounted vertical cable managers, a top mounted cable manager and our unique 2-piece cable chimney.

NO. DESCRIPTION

1 VERTICAL CABLE MANAGEMENT

2 DOUBLE DOOR CABLE MGT

3 VERTICAL CABLE MGT EXTENSION

4 TOP CABLE MANAGEMENT

5 CABLE CHIMNEY 4 X 4

6 END CAP

NO. DESCRIPTION

1 HIGH DENSITY CABLE MANAGEMENT

2 HIGH DENSITY CABLE MGT WITH DOOR

2

1

3

4

5

6

1

2

Re

lay

Ra

ck

s


Part No. Width Depth HeightCBMCHM-043604-BK 4 4 36CBMCHM-044804-BK 4 4 38

Cable Chimney

Part No. Width RU DepthCMRSPL-084407-BK 8 44 7 CMRSPL-084807-BK 8 48 7 CMRSPL-124407-BK 12 44 7 CMRSPL-124807-BK 12 48 7

High Density Cable Management

Part No. Width Depth HeightCMREXT-052406-BK 5 6 24CMREXT-053606-BK 5 6 36CMREXT-054806-BK 5 6 48

Cable Management Extension

*Two section door

Part No. Width Height RUCMRSTD-052406-BK 5 6 24CMRSTD-054406-BK 5 6 44CMRSTD-054806-BK 5 6 48CMRSTD-074406-BK 7 6 44CMRSTD-074806-BK 7 6 48CMRSTD-104406-BK 10 6 44CMRSTD-104806-BK 10 6 48CMRDBD-054406-BK* 5 6 44


Part No. Width Height RUCMRTOP-300506-BK 30 6 5CMRTOP-340506-BK 34 6 5 CMRTOP-610506-BK 61 6 5

Top Cable Management

Part No. Width Height RUCMRSDC-000506-BK 0 6 5

End Cap for Top Cable Management

Part No. Width RU DepthCMRSDR-084407-BK 8 44 7 CMRSDR-084807-BK 8 48 7 CMRSDR-124407-BK 12 44 7 CMRSDR-124807-BK 12 48 7

High Density Cable Management with Door


*

Relay R

acks

Our Rackmount, or horizontal cable management lets you manage your cables horizontally throughout your cabinets or relay racks. Choose from the simple, yet eff ective PVC conduit, our steel cable management units which have an easy access hinged front doors, or the horizontal cable retainers for quick cable access, or our new easy to use Velcro cable conduits.

Part No. Width Height RUHCMSTD-190103-BK 19 1.75 1HCMSTD-190203-BK 19 3.50 2HCMSTD-190403-BK 19 7.00 4HCMSTD-230103-BK 23 1.75 1HCMSTD-230203-BK 23 3.50 2HCMSTD-230403-BK 23 7.00 4

Standard Horizontal Cable Management

Our standard model of horizontal cable management isfor use in relay racks or cabinets. Cable managementincludes a hinged magnetic front door, cable openings ontop, bottom and rear with cable tie lancings punched intothe rear of the unit for easy cable organization.

Part No. Width Height RUHCMREC-190103-BK 19 1.75 1HCMREC-190203-BK 19 3.50 2HCMREC-190403-BK 19 7.00 4HCMREC-230103-BK 23 1.75 1HCMREC-230203-BK 23 3.50 2HCMREC-230403-BK 23 7.00 4

Recessed Horizontal Cable Management

Our recessed model of horizontal cable management isfor use where space is limited. Its recessed design allowsgood cable management while not sticking too far out infront of your connectivity. It includes all the cablemanagement features of our standard units.

Part No. Width Height RUHCMRET-190103-BK 19 1.75 1HCMRET-190204-BK 19 3.50 2HCMRET-230103-BK 19 1.75 1 HCMRET-230204-BK 23 3.50 2

Horizontal Cable Retainer

This unit makes your cable management projects quick and simple. A series of small steel “fingers” make routing cables easy. Rear panel is made from 14 ga. steel.

Part No. Width Depth RU HCMHTY-190204-BK 19 4.6 2

High Density Cable Tray

Part No. Width Height RU Depth HCMROV-190003 19 0 0 3 HCMROV-190005 19 0 0 5

Cable Support Rod with Velcro Tie Wrap

New zero RU horizontal managers with velcro tie wraps.

Part No. Width Height RU Depth HCMH1S-190105-BK 19 1.75 1 5HCMH1S-190205-BK 19 3.5 2 5

High Density Horizontal Cable Management

NO. DESCRIPTION

1 HORIZONTAL CABLE MANAGEMENT

2 HORIZONTAL CABLE RETAINER

3 HIGH DENSITY CABLE TRAY

4 CABLE SUPPORT ROD WITH VELCRO

5 HIGH DENSITY HORIZONTAL CABLE MGT

Part No. Description BPSFDS-190100-BK (19 x 1 RU) Panel Formed SteelBPSFDS-190200-BK (19 x 2 RU) Panel Formed SteelBPSFDS-190300-BK (19 x 3 RU) Panel Formed SteelBPSFDS-190400-BK (19 x 4 RU) Panel Formed SteelBPSFDS-190500-BK (19 x 5 RU) Panel Formed SteelBPSFDS-190600-BK (19 x 6 RU) Panel Formed SteelBPSFDS-190700-BK (19 x 7 RU) Panel Formed Steel

Blanking Panels

5

4

2

1

3




*


Open Ring Flip Door 3.5 “ DeepFlip Door 5.25” DeepDouble Sided Flip Door


Color Black Other_______________

Notes

Fiber Tray

19”23”

Mounting Width

Overall Height: Drilled and Tapped 48”(1219mm) 24 RU One side 70”(1778mm) 40 RU Both Sides 83”(2108mm) 44 RU 90”(2286mm) 48 RU Other ________

High Density w/ Fiber spools Cable Manager w/door

Shelves

Front Mount 3 RU

Keyboard/Monitor 7 RU Center Mount 2 RU

Heavy Duty Front Mount Heavy Duty Center Mount (May Increase RU) Front Mount Sliding 3 RU

(May Increase RU)

Depth______

Frame Size

1 U2 U

3 U 4 U

Cable Chimney

(5”W x 6” D)

Top Horizontal Management

BasicPDU`s

Metered

Switched Monitored

Managed

_____ Number of Outlets _____ Type Of Outlet_____ Cord End Type_____ Length of Cord

VerticalHorizontal

24 “36”48”

8” W x 7” D12” W x 7 “DWith DoorsFront & Back

5” W x 6” D7.5 “W x 6” D10” W x 6” D


City Province


Phone Email

Front & Back

Grounding 5 ft Grounding Cable w/ Lug Horizontal Bus Bar (19"L x 1"H x .187"D) 10 ft Grounding Cable w/ Lug

Blanking Panels

1U Qty ___2U Qty ___3U Qty ___4U Qty ___5U Qty ___6U Qty ___7U Qty ___

Qty___

Quantity of

Racks

Required ________

Qty___

Qty___

2 Post Rack Ordering GuideR

ela

y R

ac

ks


Relay R

acks

4 Post Racks

B

C

A

Open 4 post racks have become extremely popular over the last couple years. They off er more stability and fl exibility than the 2 post solutions. Electron Metal AIG off ers 4 standard stock models with adjustable depths to simplify things. However customizing is our specialty so please call us if you need diff erent size options. Electron Metal AIG also off ers many vertical, horizontal, front to back and top management options.

* Features:

Robust 12awg steel welded mounting rails

Heavy Duty welded base plates for great stability and anchoring

Universal Cage Nut Rails (ships with 100 cage nuts)

2 models covering 26” – 42” depths

Easy to install with limited number of parts

Side mounting holes for attaching cable management or accessories

Ability to gang multiple 4 post racks together

Work with many 2 post rack and cabinet accessories

Easily customizable to your specifi c requirements

Compact shipping dimensions reduce freight costs

Also available with tapped rails


Part No. Width Depth Height RU A B CRKDKIC-194428-BK 20.5 26 - 38 82.7 44RKDKIC-194432-BK 20.5 30 - 42 82.7 44RKDKIC-194828-BK 20.5 26 - 38 89.7 48RKDKIC-194832-BK 20.5 30 - 42 89.7 48





Open Ring Flip Door 3.5 “ DeepFlip Door 5.25” DeepDouble Sided Flip Door

Color Black Other_______________

Notes

Fiber Tray

Shelves

Front Mount 3 RU

Keyboard/Monitor 7 RU Front & Rear Mount 1 RU

Heavy Duty Front Mount Sliding 3 RU Front & Rear Mount Sliding 1 RU Vented

(May Increase RU)

Depth______

Blanking Panels

1 U2 U

3 U 4 U

Cable Chimney

(5”W x 6” D)Top Horizontal Management

1U Qty ___2U Qty ___3U Qty ___

BasicPDU`s

Metered

Switched

4U Qty ___5U Qty ___6U Qty ___7U Qty ___

Monitored

Managed

_____ Number of Outlets _____ Type Of Outlet_____ Cord End Type_____ Length of Cord

VerticalHorizontal

24 “36”48”


City Province


Phone Email

Grounding 5 ft Grounding Cable w/ Lug Horizontal Bus Bar (19"L x 1"H x .187"D) 10 ft Grounding Cable w/ Lug

Overall Height:

83”(2108mm) 44 RU 90”(2286mm) 48 RU Other ________

Vertical Rails: Drilled and Tapped Cage Nuts

Depth: 26" to 38" (660mm to 965mm) 30" to 42" (762mm to 1067mm)


High Density w/ Fiber spools Cable Manager w/door8” Wx 7” D12”W x 7 “DWith DoorsFront & Back

5” W x 6”D7.5 “W x 6”D10”W x 6”D

Universal Accessories Channel

Qty___

Quantity of

Racks

Required ________

Qty___

Qty___

4 Post Rack Ordering Guide


WALL MOUNTS Wall M

ounts


* Wall Mount Cabinet Features:

Fully welded 14 ga. & 16 ga steel construction

Accepts 19” rackmount equipment

Swing out mid-section with lock

Locking front acrylic door

Provides easy access to equipment

Fan cutouts and cable entry cutouts

Various sizes available

Our wall mount cabinet provides a secure method of mounting your equipment to the wall. This fully enclosed cabinet provides protection from dust and other elements that an open fi xture cannot provide. The cabinet also features the added security of a locking front acrylic door. A hinged 4” front section swings out to allow easy access to the rear of your equipment.


Part No. Useable Panel Overall Overall Overall Equipment Height Space Depth Width Height Depth RU A B C D E F WMCSTD-191216-BK 12 21 19 17 24 26 10WMCSTD-191221-BK 12 21 19 22 24 26 16WMCSTD-191621-BK 16 28 19 22 31 26 16

Wall Mount CabinetW

all

Mo

un

ts


Wall Mount Cabinet


Wall M

ounts


Reverse Wall Mount Cabinet

Our reversed wall mount cabinet is similar to our standard wall mount cabinet, but its layout is reversed. The 4” hinged section is mounted on the rear of the cabinet, so your equipment can be installed into the deep mid section of the cabinet, allowing for much deeper equipment than other models. This cabinet also includes a locking front acrylic door, cable entry cutouts on the rear sections, and fan cutouts for optional ventilation fans. The cabinet also has sliding PMA’s for even greater adjustability, just like our full size cabinets.

* Reversed Wall Mount Cabinet Features:

Fully welded 14 ga. & 16 ga. steel construction

Top and bottom cutouts for fans or cable entry

Locking front acrylic door

Locking swing out rear section

Adjustable PMA’s

Many sizes available

19” or 23” rackmount

A

B

25 3/32"20"

4"

Part No. A B RUWMCRCM-231224-BK 24 26 12 WMCRCM-231624-BK 31 26 16 WMCRCM-232124-BK 39.75 26 21


Part No. A B RUWMCREV-191224-BK 24 22 12 WMCREV-191624-BK 31 22 16 WMCREV-192124-BK 39.75 22 21

Reversed Wall Mount Cabinet Reversed Wall Mount Cabinet with (2) Vertical Cable Mgt

Dimensions shown in inches Dimensions shown in inches

SlimLine Wall Mount Cabinet

Our SlimLine wall mount Cabinets were designed for applications where a traditional deep wall mount Cabinet or Rack will not work because of reduced space. Typically used in hallways or small telecom closets, our SlimLine Cabinets allow you to mount your equipment vertically so that the depth of the cabinet is kept to a minimum.

* SlimLine Features:

Slim design allows for installation almost anywhere

Lockable door for security

Dustproof versions for industrial or dirty applications

Variety of sizes to suit your requirements

Multiple cable entry points

* Customize to your exact requirements

C

C

D D

36"

25 1/2"

3 1/4"(2RU)

26"

10 1/8"8"

(4RU)


Wa

ll M

ou

nts


Part No. Height Width Depth RUWMCLOP-190436-BK 36 26 8 4

SlimLine Wall Mount Cabinet


Wall M

ounts


Wall Mount Swing-Out Rack

* Swing-Out Wall Mount Relay Rack Features:

Easy bolt together construction

Designed to accept up to 75 lbs of equipment

Easily reversible swing out section

19” rackmount applications

Many sizes available to suit your requirements

Includes all hardware for easy assembly

This rack is designed to support smaller equipment. It allows easy swing-away access to the rear of your equipment. This rack features bolt-together construction for easy installation. This rack can hold up to 75 lbs of equipment and can be installed to pivot either left or right. It is also available in a heavy duty construction, and is capable of holding up to 150lbs of equipment.


A

20"

B

A

20"

25"

Part No. A B RUWRSSLD-191212-BK 28.63 12 12WRSSLD-191218-BK 28.63 18 12WRSSLD-192018-BK 28.63 18 20

Part No. A RUWRSSHD-191225-BK 28.63 12WRSSHD-192025-BK 42.63 20

Swing-Out Wall Mount Rack - Light Duty Swing-Out Wall Mount Rack - Heavy Duty



Wall Mount Rack

The wall mount relay rack is great for situations where plenty of heavy equipment is required to be wall mounted. This rack will support more weight and more equipment than a standard wall mount bracket. It has similar construction as our standard relay racks and includes brackets to fi x the frame to a wall. Holes are tapped 10-32 at standard E.I.A. spacing on the front only.

* Wall Mount Relay Rack Features:

Accepts more equipment than wall mount brackets

Designed for 19” rackmount equipment

Extra long mounting brackets provide ample room for deep equipment

Many heights available

Includes mounting holes for cable management accessories

Part No. Useable Panel Overall Overall Overall Height Space Depth Width Height RU WMRFIX-191216-BK 12 21 19 19.25 20.5 24.25 WMRFIX-192016-BK 20 35 19 19.25 20.5 38.25 WMRFIX-192416-BK 24 42 19 19.25 20.5 42.25


Wa

ll M

ou

nts


Wall Mount Rack


Wall M

ounts


* Wall Mount Bracket Features:

Light weight, sturdy construction

Pre-punched holes for wall mounting

Large cable access cutout on rear

Includes many cable tie-down lancings

Availablity of single or double hinges

Adjustable depth model also available

Accepts 19” equipment

Large variety of models and sizes

Wall Mount Brackets

Electron Metal AIG off ers a wide variety of wall mount brackets. These are used when smaller equipment is required to be mounted on a wall, such as patch panels and other small equipment. Great for use in small offi ce networking rooms. Brackets come with either one or two hinges, for easy access to the rear of equipment, cable entry hole on rear, cable tie down lancings, and rails pre-tapped 10-32 at standard E.I.A. spacing. Available in 19” rackmount only, fi xed depth or adjustable.


Part No. Height Width Depth RUWMBHD2-190206-BK 3.5 20 6 2 WMBHD2-190406-BK 7 20 6 4WMBHD2-190806-BK 14 20 6 8

Part No. Height Width Depth RUWMBADJ-190414-BK 7 20 9 to 14 4 WMBADJ-190614-BK 10.5 20 9 to 14 6WMBADJ-190814-BK 14 20 9 to 14 8

Wall Mount Bracket, Double Hinged, Fixed Depth Wall Mount Bracket, Adjustable Depth

Dimensions shown in inches Dimensions shown in inches

SHELVES & DRAWERS

1 2 3 4 5 6Select Shelf Type Select Sub Type Select Width Select Height Select Depth Select Color

Type Description Sub-Type Description Width Height RU Depth ColourSHF Fixed Shelves FMT Front mount 19 01 12 BK for BlackSHD Heavy Duty Shelves FRM Front/rear mount 23 02 14 GY for GreySHS Sliding Shelves CMT Center mount 03 15SHK Keyboard Shelves SMT Side mount 04 16DRW Drawers ADJ Adjustable 05 18

ADV Adjustable vented 06 20FRV Front/rear mount vented 22CMV Center mount vented 24FMV Front mount vented 26SMV Side mount vented 28MTM Monitor/keyboard tray, wide (keyboard only) 30MTY Monitor/keyboard tray, narrow (keyboard only) 32PFM Front mount pivoting (keyboard only) 34CFM Combination front mount (drawers only)CFR Combination front/rear mount (drawers only)CSM Combination side mount (drawers only)

SHF FMT -19 03 18 -BK 1 2 3 4 5 6

Part Number Configurator For Electron Metal Shelves

Electron Metal AIG has been making custom cabinets, shelves and accessories for the Telecommunication, IT, Security and Broadcast markets for over 30 years. If you do not see a standard product in the catalog that that meets your needs please call us because we CAN make it for you. Our manufacturing fl exibility, quick turn around and competitive pricing is what keeps our customers coming back time and time again.

Shel

ves

& D

raw

ers



*

Shelves & D

rawers

SHELVES & DRAWERS

Part No. Width Depth RU SHDFMT-190418-BK 19 18 4 SHDFMT-190420-BK 19 20 4

Heavy Duty Front Mount Shelf

Part No. Width Depth RU SHFADJ-190124-BK 19 24 - 32 1 SHFADJ-190128-BK 19 28 - 36 1

Front & Rear Mount Shelf - Adjustable Rear Supports

Part No. Width Depth RU SHFFMT-190212-BK 19 12 2 SHFFMT-190316-BK 19 16 3SHFFMT-190318-BK 19 18 3SHFFMT-190324-BK 19 24 3

Front Mount Shelf

Part No. Width Depth RU SHKFMT-190318-BK 19 18 3SHKFTY-190210-BK 19 10 2

Front Mount Keyboard Shelf

Part No. Height Width Depth RU SHFADV-190124-BK 1.75 19 24 1SHFADV-190128-BK 1.75 19 28 1

Vented Adjustable Shelf

Part No. Width Depth RU SHFCMV-190218-BK 19 18 2

Center Mount Shelf - VentedPart No. Width Depth RU SHSFMT-190318 -BK 19 18 3SHSFMT-190324-BK 19 24 3

Front Mount Sliding Shelf

Part No. Width Depth RU SHSFRM-190118-BK 19 18 1 SHSFRM-190124-BK 19 24 1SHSFRM-190128-BK 19 28 1

Front Mount Sliding Shelf

Part No. Width Depth RU SHDCMT-190318-BK 19 18 3 SHDCMT-190324-BK 19 24 3 SHDCMT-190328-BK 19 28 3

Heavy Duty Center Mount Shelf

Part No. Width Depth RU SHFCMT-190218-BK 19 18 2 SHFCMT-190224-BK 19 24 2

Center Mount Shelf

Part No. Width Depth RU SHKCMT-190218-BK 19 18 2

Center Mount Keyboard Shelf

Part No. Width Depth RU SHKMTA-190216-BK 19 16 2

Part No. Width Depth RU SHKFST-190114-BK 19 14 1

Keyboard/Monitor Shelf

1 RU Keyboard Shelf

Part No. Height Width Depth RU DRWCFM-190220-BK 3.5 19 20 2

Front Mount Combination Drawer

Part No. Height Width Depth RU SHFZAD-190124-BK 1.75 19 24 1

Heavy Duty Front & Rear Mount Shelf

Zone 4 Capacity: 105 Lbs

Part No. Height Width Depth RU DRWCFR-190216-BK 3.5 19 16 2

Front/Rear Mount Drawer

Electron Metal AIG has many shelf options but our ability to off er almost anything our customers require is what sets us apart. If you do not see a standard product that fi ts you application please contact us we can come up with the perfect solution for your application.



*

Security Options

* Security Options:

Standard Key Locks

Key Code Locks

Swing Handle Locks

Self-locking Slam Latches

Padlock Handles

Magnetic Locks

Combination Locks

Digital Locks

Access Cards

Monitoring Solutions

Security options are an important part of any cabinet solution. Electron Metal AIG has been supplying cabinets for over 30 years and has a tremendous amount of experience in providing the right security solutions. Whether you need standard locks, key coded locks, self-locking doors, card scanners, monitoring or no locks at all, Electron Metal AIG can provide a solution for you. We will also work with your security integrator to ensure compatibility with existing security or monitoring systems. For more information visit our website at www.electronmetal.ca or call us at 1-866-96-RACKS.


Acc

ess

ori

es


Ventilation and Air Conditioning

* Ventilation and Air Conditioning Options:

Fans

Blowers

Top Mount Air Conditioners

Side Mount Air Conditioners

Rear Door Air Conditioners

Hot Air Exhaust Chimneys

Rear Door Heat Exchangers

Hot Aisle Containment Systems

Cold Aisle Containment Systems

Cooling the equipment in an enclosed cabinet has always been important. With today’s IT equipment’s heat loads increasing, this is becoming even more important and challenging. Electron Metal AIG has been incorporating ventilation and cooling into our cabinet solutions for decades. Whether you need a simple fan solution or 25kW blower solutions, Electron Metal AIG can help with almost any cooling requirement. We can incorporate top mount or side mount air conditioners, rear door heat exchangers and forced air chimney solutions depending on your application. If you have cooling issues or want to design a future proof system that will grow with your heat loads, Electron Metal AIG can always help come up with a cost eff ective and reliable solution.



Accessories

Electron Metal AIG off ers a wide array of Mounting Rails, Brackets, Blanking Plates, Casters, Leveling Feet and Hardware or we can customize something for your exact requirements. For more information visit our website at www.electronmetal.ca or call us at 1-866-96-RACKS.

* Mounting Rails Features:

All rails off er standard EIA spacing

Cage nut or drilled and tapped

RU markings on mounting rails

One piece solid 12 ga. Steel

Variety of sizes and models

Simplify your installations

Customize your own if required

Mounting Rails & Hardware

RU markings on rails


Acc

ess

ori

es q u a l i t y

f lex ib i l i t y va lue s e r v i c e

Today, the Mounting Rails in your cabinets are for more than just mounting equipment. They can be a vital part of your cable management strategy and help keep your servers and other equipment cool. Electron Metal AIG has many options for your Mounting Rails and few of which are shown here. For more information to customize your own features call us at 1-866-96-RACKS.

HARDWARE


Accessories

Part No. DescriptionCASSP4-000300-BK Set of 4 Pivoting 3" Casters with Series 4000 Mounting Plates (black)CASSTC-190300-BK Set of 3” casters (2 with brake) with (19”) channels

Caster KitPart No. DescriptionSCWOHN-103208 Oval Head Screw 10-32 x 0.5 nylon washer black (100)NUTCAG-1032 Cage-Nuts 10-32 (nut retainer) (100)SCWTQZ-103208 Truss Head Machine Screw Quadrex 10-32 x 1/2 (100)

Screws and Nuts

Part No. Description RURALABR-020100 Pair Adaptor Brackets (23 - 19 x 1.75) 1RALABR-020200 Pair Adaptor Brackets (23 - 19 x 3.5) 2RALABR-020300 Pair Adaptor Brackets (23 - 19 x 5.25) 3RALABR-020400 Pair Adaptor Brackets (23 - 19 x 7) 4

Adaptor Brackets


Grounding



Pass Through with rubber

grommet to protect cable and

reduce air leakage

Grounding is not only very

important for the safety of

your equipment, with the

increased loads per cabinets it

is vital to the life safety of your

staff. Electron Metal AIG can

pre-install grounding buses to

help ensure you can ground

your equipment appropriately.

Fibre or copper Slack Spools

help manage excess cable

Velcro Ties mounted on rails for

extra cable management

AirLock Brushes to help protect

cables and manage airflow

LAN Furniture

Single LAN Rack

Our LAN racks are an ideal solution for networking storage and workstations. The racks feature modular components and construction providing almost limitless adjustability and customization. With its open design, it allows easy access to both the front and rear of your equipment. Each rack features concealed cable management in its vertical members, as well as through the horizontal stiffeners, to keep your cabling in order. Shelves and other accessories can be adjusted in increments. All our racks feature a simple “hook on” system for shelves and accessories. Your components simply hook onto the LAN frame, without the need for any special tools or hardware.

Double LAN Rack

Our LAN racks are also available in a double configuration. The rack includes long support legs on both sides for maximum stability. Mounting holes are equipped on the front and rear of the rack to allow shelves and other equipment to be installed on both sides simultaneously. Great for smaller areas that require more capacity with a smaller footprint.

D

B

F

AE

C

D

B

F F

AE

C

D

B

A E

C

Work Station

Our user-friendly workstation is ideal for repair, assembly and service technicians. With its large table surface, it offers a clean and uncluttered work area. A rear-mounted powerbar allows for multiple electrical connections and large overhead fluorescent lights supply ample illumination. The heavy-duty frame is constructed of welded steel and has a reinforced base with a non-slip rubber surface footrest. The frame comes standard with a series of holes and cutouts to allow easy repositioning of accessories. Large shelves allow easy access to equipment and also provides for close-at-hand storage.

Part No. Usable Usable Overall Overall Overall Usable Height Width Depth Width Height Depth A B C D E FLANFRA-248418-BK 75.375 22.75 22.50 24 84 16LANFRA-248424-BK 75.375 22.75 28.50 24 84 22LANFRA-248430-BK 73.375 22.75 34.50 24 84 28

24” Wide Model


30” Wide Model


36” Wide Model

Part No. Usable Usable Overall Overall Overall Height Width Depth Width Height A B C D E LANFRD-248418-BK 75.375 22.75 35.50 24 84 LANFRD-248424-BK 75.375 22.75 47.50 24 84 LANFRD-248430-BK 73.375 22.75 59.50 24 84

24” Wide Model


30” Wide Model


36” Wide Model

Custom sizes available upon request. Please contact a customer service technician.

Part No. Usable Usable Overall Overall Overall Height Width Depth Width Height A B C D E LANKWS-487232-BK 69 45.50 32 48 72

48” Wide Model

LAN

Fur

nitu

re



*

Co

nso

les

Electron Metal AIG off ers a complete A to Z solution for all your custom console requirements. We work in conjunction with the client to ensure a tailormade product for each project. In each case our team ensures that the design, structure, fi t & fi nish and ergonomics conform fully to the client’s needs and expectations. This meticulous approach coupled with over 30 years of experience is what puts Electron Metal AIG in a class all its own.

CONSOLES


* Our custom consoles have become the

product of choice across a broad spectrum

of industries, such as:

Broadcast

Security

Law Enforcement

Aviation

Research Labs

Satellite Stations

Traffi c Control

Installation Monitoring

Electron Metal AIG has helped many customers with small and simple to extremely large and challenging technology rollouts. Major and regional Banks/Credit Unions, Retail Chains, Service Providers, Grocery Chains, Government Agencies and others have utilized Electron Metal AIG’s services to help ensure a successful technology deployment. If you or one of your customers have a regional, national and global rollout planned Electron Metal AIG can help ensure your project runs smoothly and you get the perfect product for your application.

* Services Include:

Concept and Design

Prototyping

Custom Fabrication

Pre-Installing customer’s equipment

Consolidation of multiple suppliers products

Staging

Logistics

ROLLOUTSR

ollo

uts


Sta

gin

g

Technology is always changing rapidly. This couldn’t be more true than in the Telecommunication, IT and Security markets that Electron Metal AIG has supported for over 30 years. As such we have a great amount of experience helping our customers with new technology rollouts or deployments. We can work directly with end-user IT departments, Engineering fi rms, Contractors/Integrators or Distributors to ensure your project goes smoothly.

One of the most popular options our customers choose is our staging solutions. This can be as simple as bundling products to ship out with our cabinets or racks so that there is reduced transport costs and paperwork, to complex pre-installation work of your equipment so that when it arrives on site it is a simple plug and play scenario. The choice on how simple or complex the staging requirements are is up to you, but we are confi dent we will save you time, money and headaches along the way!

For more information on how Electron Metal AIG can help stage your next products please contact your local representative. For more information on how Electron Metal AIG can help Stage your next products please contact your local representative.

STAGING

Preloaded rack or cabinets to your specifi c requirements saves time and money

Safely packaged to minimize possible damage

Multiple products consolidated and shipped to site for speedy deployment Various shipping methods for on time delivery


Cus

tom

Wor

k

Unlike most manufacturers who do not like to deviate from their standard set of products, Electron Metal AIG’s business was built on tailoring products to our customers exact requirements. Even though we have a very broad and competitive off ering today we still prefer to customize our products so that they best meet our customer’s needs and wants.

Electron Metal AIG has been making custom cabinets, rack, consoles, LAN Furniture, shelves and accessories for the Telecommunication, IT, Security and Broadcast markets for over 30 years. If you do not see a product in this catalog that that meets your needs please, please call us because we CAN make it for you. Our manufacturing fl exibility, quick turn around and competitive pricing is second to none, and is what keeps our customers coming back time and time again. We can fi nd a cost-eff ective solution for any application.

CUSTOM WORK


Top 4 Things to Consider When Ordering a Cabinet

1. CompatibilityThe number one concern for end users is will the IT equipment mount or fi t in the cabinet. The answer is typically yes. The mounting rails in most cabinets are built to industry standards that guarantee interoperability. The bigger question is will your cabinet be able to house your current and future equipment depth, cabling requirements and cooling needs? Can it be expanded if you need more depth in the future? Does it off er enough cable entry points? Can cooling options be added? Although cable management and cooling issues are close, the number one reason for replacing existing cabinets is because new electronic equipment will not fi t. Electron Metal AIG’s cabinets have been designed so that extensions can be easily added in the future. We also have many cable management and cooling options so that total replacement of the cabinets should often not be required. We have added these features to future proof the investment our customers make with us. 2. Environmental RequirementsThere are many environmental considerations when ordering a cabinet. Will the cabinet be in a clean room or a dirty location? Will it be subject to dust, moisture, hot or cold environments etc. The basic environmental conditions are typically planned for, but what is often missed is how much heat the equipment is going to generate and can the cabinet selected exhaust that much heat? All computer and electronic equipment create heat. Your cabinets need to be able to dissipate that heat effi ciently, or your equipment will potentially overheat, shutdown, and in the worst cases be physically damaged. If this is planned for, the next question needs to be what happens if the heat load increases? Cabinet heat loads have incrementally been increasing for several years. Rack power and heat loads that were once considered impractical are now common. New, high density computer designs can increase heat density to as much as 30kW/h per rack. High density computing brings a new set of design challenges for cabinets. Can future onsite modifi cations be made to improve cooling effi ciency and performance? Our cabinet designs are optimized for effi cient cooling now. Using our retrofi t kits, we are easily compatible with various cooling topologies and have non-liquid solutions tested to exhaust 25kW/h per cabinet. Using Electron Metal AIG’s Thermal containment solutions can save thousands in annual electrical expenses, and lower your company’s carbon footprint. Call us for an onsite evaluation today. 3. Cable ManagementAs heat loads and power densities grow, so does the structured cabling system that supports it. Data Centers have to provide higher bandwidth to properly deliver services to internal and external customers. Higher bandwidth means higher switch port density, and much thicker cables which are diffi cult to manage. Proper cable management is critical. Cable pathways that used to support legacy applications like CAT5e will quickly become a bottleneck as your network migrates to Category 6A and beyond. High density switches now use up to 1536 Category 6 cables in a single cabinet. Cabinets used with a small space have an effi cient footprint and make great use of valuable data center fl oor space, but can easily be the wrong choice for applications requiring high density cable management. Electron Metal AIG helps you make the right cabinet selection for applications of today and tomorrow. 4. Power & GroundingMore data processing = More power. Port densities are on the rise. Server virtualization continues to be widely deployed, increasing the power requirements per cabinet even more. Applications that in the past used 110V single phase 15 AMP power distribution strips, now often call for 208V 3 phase 60 AMP electrical feeds. With this increased electrical load deployed in cabinets, safety is becoming a serious concern. It is estimated by industry associations that over 50% of installed IT cabinets are not grounded or bonded at all. Cabinets that are grounded often do not conform to industry specifi cations, or the Canadian Electrical Code. All Electron Metal AIG racks and cabinets have grounding/bonding points. We off er pre-terminated grounding cables, and grounding bus bars for all of our Racks and Cabinets to help ensure equipment and maintenance staff remain safe. Electron Metal AIG also off ers a variety of standard and customized vertical and horizontal power distribution units. Selecting the appropriate PDU is critical for new equipment deployments and, as with our cabinets, we can customize our PDU’s to your exact requirements. Electron Metal AIG can pre-install your customized power distribution units into your racks prior to packaging and shipping; for no additional cost.

Technical PagesT

ec

hn

ica

l Pa

ge

s

Rack Units (RU)Standard EIA Spacing

All of Electron Metal AIG's quality products adhere to strict industry standards for Rack Units, Rack Spacing and EIA hole spacing.

One "Rack Unit" (RU) is equalto 1.75".

Each product is measured in multiples of RU's.

Mounting rails and accessories are drilled and tapped 10-32 UNF at standard EIA spacing (see chart on right). Cage nuts are also available.

Electron Metal AIG offers products in either 19" or 23" rackmount widths. We also have the capability to fabricate non-standard sizes.


Technical Pages

Manager Size Width Depth

Cat 5e Cat 6 Cat6 +Cat 6A

Gen 1

Cat 6A

Gen 2

5" X 6 " 5 6 30

7.5 " X 6 " 7.5 6 45

8" X 7 " 8 7 56

10" X 6 " 10 6 60

Vertical Manager Cable Capacity Estimator

Cross

Sectional

Area

Estimated Number of Cables based on 50%

capacity and Typical Cable size

12" X 7 " 12 7 84

Manager Size Depth Height

1.75 " X 2.5" 2.5 1.75 4.38

1.75 " X 3" 3 1.75 5.25

3.5" X 3" 3 3.5 10.5

5.25" X 3.5" 5.25 3.5 18.38

Cross

Sectional

Area

Estimated Number of Cables based on 50%

capacity and Typical Cable size

3 " X 7" 3 7 21

39 28 28 11 15

47 34 34 14 18

93 68 68 27 18

164 119 119 48 64

187 137 137 55 74

267 195 195 78 105

401 293 293 117 158

534 390 390 156 210

498 364 364 146 196

748 546 546 218 294

Horizontal Manager Cable Capacity Estimator

Note: The calculations within the Manager Capacity Estimator are based upon Industry practices, however, the results between different calculation methods may vary. The results are to be used as a general guideline and Electron Metal AIG cannot be held responsible for this information as it pertains to your installation. Proper size selection is the sole responsibility of the installer. Be sure to check local codes.

OD 0.19 OD 0.22 OD 0.22 OD 0.35 OD 0.295

Cat 5e Cat 6 Cat6 +Cat 6A

Gen 1

Cat 6A

Gen 2

OD 0.19 OD 0.22 OD 0.22 OD 0.35 OD 0.295


Te

ch

nic

al

Pa

ge

s



*

Technical Pages


GLOSSARYAmp - a unit of electrical current.

Aisle - The open space between rows of racks.

ASHRAE - American Society of Heating, Refrigerating and Air-Conditioning Engineers

Blanking Panel - A device that is installed into unused rack spaces. Using blanking panels improves the effi ciency and capacity of the Data Center cooling system.

BTU - British Thermal Unit, a unit of energy.

Cabinet - A standardized frame or enclosure for mounting multiple equipment modules.

CFM - Cubic Feet per Minute, often cooling systems airfl ow is specifi ed in CFM.

Close-Coupled Cooling - Cooling that occurs close to the heat load – This improves effi ciency and capacity.

Cold Aisle - The aisle between racks that feeds the IT equipment cool air.

cQPS – The Standards Council of Canada has certifi ed QPS Evaluation Services, Inc. as an “Accredited Testing Laboratory and Certifi cation Body”. QPC can test and certify products for safe use in Canada as does CSA International, Underwriters Laboratories Inc. (UL) and Intertek Group plc. (ETL). Products marked with a CSA, cUL, cETL or cQPS label are deemed tested and approved for safe use in Canada. The QPC is not as widely known as CSA, UL and ETL but the cQPC Mark is a direct equivalent to CSA, cUL or cETL according to, and approved by, the Standard Council of Canada. For more information visit http://www.qps.ca/CertCanada.html

CRAC - Computer Room Air Conditioner

CRAH - Computer Room Air Handler

Delta T - The diff erence between the entering and exiting temperature in a cooling system.

EMI (electromagnetic interference) - “Noise” generated in copper conductors when electromagnetic fi elds induce currents. EMI may be caused by other copper cables and is caused by proximity to motors and machinery. The all dielectric optical fi ber cable design makes them immune to EMI.

Equipment Room (ER) - A centralized space for telecommunications equipment that serves the occupants of a building. An equipment room is considered distinct from a telecommunications closet because of the nature or complexity of the equipment.

ESD - Electrostatic Discharge

Gigabit Ethernet (GE or GbE) - This standard was written by the IEEE 802.3 committee and adopted as a new standard for Gigabit transmission of LANs.

Hot Aisle - The Aisle between racks that is designated for exhaust air that needs to be cooled.

In-Row Cooling - A cooling technology that removes heat at the rack and row level. This close coupled cooling approach is effi cient and can handle extremely high densities.

Local Area Network (LAN) - A network connecting several nodes within a limited geographic area, usually within a building or campus

OEM (Original Equipment Manufacturer) - An OEM maker is a manufacturer of original equipment. A company who buys their components from someone else and simply assembles the components into a product is not considered an OEM and is often called a value-added reseller.

PDU – Power Distribution Unit - Typically installed in a rack or cabinet. Can be vertical or horizontal with a variety of receptacle types.

Plenum - A compartment or chamber to which one or more air ducts are connected and that forms part of the air distribution system (i.e. the space above the drop ceiling).

PUE - Power Use Eff ectiveness

Rack - A device used for mounting IT equipment.

Raised Floor - An artifi cial fl oor installed above the natural fl oor that creates space for cable management, or cold air distribution. Still common, but by no means required.

RoHS-Compliant - (The Restriction of Hazardous Substances

Directive) - RoHS-compliant was adopted in February 2003 by the European Union. The RoHS took eff ect on July 1, 2006, but is not a law; it is simply a directive for participating countries, including the European Union (exclusive of the United States and many other countries). This directive restricts the use of six hazardous materials in the manufacture of various types of electronic and electrical equipment. RoHS-compliant is often referred to as the “lead-free” directive.

RU - A unit of space in a rack, equal to 1.75” Cabinets are typically discussed in U’s, as this is the area in an enclosure for rackmount equipment.

Telcordia Technologies - Formerly Bellcore, a research company once owned by the RBOCs. TIA (Telecommunications Industry Association) - TIA represents the telecommunications industry in association with the EIA (Electronics Industry Association) and creates telecommunications standards.


NotesN

ote

s

Why should you need to try to fi t your products and

applications into someone else’s cabinet? At Electron Metal

AIG, our strength has always been the fl exibility to off er you

customized solutions for your specifi c applications. Our

state of the art 80,000 sqft plant allows us to deliver on a

very broad range of products for your needs and wants.

FLEXIBILITYf lex ib i l i t y

No premiums for your customized solutions

No large minimum order quantities

Wide scope of product designs & manufacturing capabilities

Ability to pre-load or pre-wire your products

ELECTRON METAL

Ours Yours

100% Canadian made Top Quality

30 years of proven service Confi dence

Customized to your specifi c needs & wants Satisfaction

Competitive pricing with no large premiums Value

Experienced team to help with fl exible designs Ease

Customer fi rst service, face to face or over the phone Trust

Logistic services to ensure your products are always there On time

Electron Metal AIG

2160 Boulevard Dagenais West

Laval, Quebec Canada H7L 5X9

Phone: 1.450.625.8064 Toll Free: 1.866.96.RACKSFax: 1.450.625.8004

E-mail: [email protected]

Website: www.electronmetal.ca

Feedback: [email protected]

What’s Ours is Yours at Electron Metal

Documents

Electron Metal Catalogue 2012