View
222
Download
0
Tags:
Embed Size (px)
Citation preview
Electromagnetics Electromagnetics (ENGR 367)(ENGR 367)
The Complete The Complete
Sourced & Loaded T-lineSourced & Loaded T-line
T-line Power: Big or SmallT-line Power: Big or Small
• While T-lines carry from the high voltage of While T-lines carry from the high voltage of Power Generators to the miniscule voltage Power Generators to the miniscule voltage detected by Communications Receivers, the detected by Communications Receivers, the load can only absorb as much signal power load can only absorb as much signal power as is transmitted, and that depends initially as is transmitted, and that depends initially on the source and input impedances. on the source and input impedances.
• To address this issue adequately, we must To address this issue adequately, we must consider the consider the fully sourced and loaded T-linefully sourced and loaded T-line..
Outline of LectureOutline of Lecture
• Model the Fully Sourced & Loaded T-lineModel the Fully Sourced & Loaded T-line
• Define Wave & Input Impedance of T-Define Wave & Input Impedance of T-lineline
• Form an Equivalent Circuit at the InputForm an Equivalent Circuit at the Input
• Observe Special Input Impedance CasesObserve Special Input Impedance Cases– For a half-wavelength lineFor a half-wavelength line– For a quarter-wavelength lineFor a quarter-wavelength line
• Work Out Examples of T-line ProblemsWork Out Examples of T-line Problems
Introduction: Practical T-lines Introduction: Practical T-lines Connect to Both Source and Connect to Both Source and
LoadLoad• Practical T-line may be mismatched at both Practical T-line may be mismatched at both
endsends
• If fully unmatched, reflections occur at If fully unmatched, reflections occur at bothboth endsends
Sourced & Loaded T-line Sourced & Loaded T-line (lossless)(lossless)(in case of lossy T-line, replace j(in case of lossy T-line, replace j with with ))• Express the Phasor line Voltage & CurrentExpress the Phasor line Voltage & Current
asas
0 0
0 0
0 0 0 0
( )
( )
where , , and may be complex
j z j z
j z j z
V z V e V e
I z I e I e
V V I I
Introduce Wave ImpedanceIntroduce Wave Impedance
• Define Wave Impedance as the Ratio Define Wave Impedance as the Ratio of Total Voltage to Current Anywhere of Total Voltage to Current Anywhere on lineon line
• In terms of the voltage reflection In terms of the voltage reflection coeff. (coeff. ())
0 0
0 0
( )( )
( )
j z j z
W j z j z
V e V eV zZ z
I z I e I e
0 00 0 0 0
0 0
0
, and
( )j z j z
W j z j z
V VV V I I
Z Z
e eZ z Z
e e
Wave Impedance Wave Impedance & Input Impedance& Input Impedance
• In terms of line and load impedancesIn terms of line and load impedances
• Define Input Impedance as the Wave Define Input Impedance as the Wave Impedance at the front (source) end Impedance at the front (source) end of lineof line
00
0
0
0
cos( ) sin( )( )
cos( ) sin( )
(by substituting and applying Euler's Identity)
LW
L
L
L
Z z jZ zZ z Z
Z z jZ z
Z Z
Z Z
0in 0
0
cos( ) sin( )@ : ( )
cos( ) sin( )L
WL
Z l jZ lz l Z Z l Z
Z l jZ l
Equivalent CircuitEquivalent Circuit• The Practical Sourced & Loaded T-line with The Practical Sourced & Loaded T-line with
ZZinin
• Acts like the equivalent circuit:Acts like the equivalent circuit:
Special Case ISpecial Case I
• Half-Wavelength (Half-Wavelength (/2) Line/2) Line– Also known as the Half-Wave Transformer (HWT)Also known as the Half-Wave Transformer (HWT)– Electrical LengthElectrical Length
– Input ImpedanceInput Impedance
• Notes on the HWTNotes on the HWT– Ideally, this T-line section is Ideally, this T-line section is transparent to the sourcetransparent to the source
and acts and acts as if it were absent from the circuitas if it were absent from the circuit– Actually, any Actually, any line loss results in less than ideal line loss results in less than ideal
performanceperformance, so , so the shortest possible section is the shortest possible section is usually preferred in applicationusually preferred in application
– Results Results depend on frequencydepend on frequency::
2 for 0,1, 2,...
2
ml m m
in ( / 2) LZ l m Z
valid only at 2pmv
fl
HWT BehaviorHWT Behavior
• Due to the length of the HWT:Due to the length of the HWT:
• Provided:Provided:
in LZ Z
22 2
2 2p
p
vl l fv l
Special Case IISpecial Case II
• Quarter-Wavelength (Quarter-Wavelength (/4) Line/4) Line– Also known as the Quarter-Wave Transformer (QWT)Also known as the Quarter-Wave Transformer (QWT)– Electrical LengthElectrical Length
– Input ImpedanceInput Impedance
• Notes on the QWTNotes on the QWT– Ideally, can be used to Ideally, can be used to match impedances at a match impedances at a
junctionjunction– Affected by line lossesAffected by line losses so shortest section preferred so shortest section preferred
– Results Results depend on frequencydepend on frequency::
(2 1) for 0,1,2,...
2
ml m
2in 0( / 4) / LZ l Z Z
(2 1)valid only at
4pm v
fl
QWT MatchingQWT Matching
• Desire:Desire:
• Provided:Provided:
202
in 01 02 01 LL
ZZ Z Z Z Z
Z
2 4p
p
vl l fv l
Examples of T-line ProblemsExamples of T-line Problems
• Consider a lossless 2-wire 300-Consider a lossless 2-wire 300- line line such as the lead-in wire from the such as the lead-in wire from the antenna to a TV or FM radio antenna to a TV or FM radio communications receivercommunications receiver
T-line Problem: Example AT-line Problem: Example A
• GivenGiven: Z: ZGG = Z = Z00 = Z = ZLL = (R = (Rinin of Rx)= 300 of Rx)= 300 vvpp = 2.5 x 10 = 2.5 x 1088 m/s and m/s and ll = 2.0 m= 2.0 m
• FindFind: : , SWR, , SWR, , , , , , Z, Zinin, V, Vinin, I, Iinin, V, VLL, I, ILL, , PPLL
• SolutionSolution: line is matched at both ends!: line is matched at both ends!
8
6
o
2.5 10 m/sa) 0 c) 2.5m
100 10 Hz
2 2 radb) 1 d) 0.8 rad/m; 0
2.5m
e) (0.8 rad/m)(2 m)
1.6 rad 288 0.8
pv
f
SWR
l
T-line Problem: Example AT-line Problem: Example A
• SolutionSolution: (continued): (continued)
1.6
1.6
f) 300 (due to matched conditions)
6 V3 V (by voltage division)
2 2
3 V10 nA
300
g) 3 V 3 V 1.6 rad
10 nA 10 nA 1.6 ra
in
s in sin
in G
inin
in
j jL in
j jL in
Z
V Z VV
Z Z
VI
Z
V V e e
I I e e
15
d
h) (due to matched conditions)
1 1(3 V)(10 nA) 15 fW( 15 10 W)
2 2
in L
in in
P P
V I
T-line Problem: Example BT-line Problem: Example B
T-line Problem: Example BT-line Problem: Example B
• GivenGiven:: a 2a 2ndnd identical Rx in parallel with 1 identical Rx in parallel with 1stst so that so that ZZGG = Z = Z0 0 = 300 = 300 ; Z; ZLL = R = Rin1in1 RRin2in2
• FindFind: : , SWR, , SWR, , , , , , Z, Zinin, V, Vinin, I, Iinin, V, VLL, I, ILL, P, PLL with with locations & values of Vlocations & values of Vminmin, ,
VVmaxmax
• SolutionSolution: Z: ZLL = (300 = (300 )) (300 (300 )) =150 =150
0
0
1 411150 300 150 1 3 3a) b) 2
1 2150 300 450 3 1 13 3
c, d, e) , , all same as before, since no changes were made to the T-line or frequency
L
L
Z ZVSWR
Z Z
T-line Problem: Example BT-line Problem: Example B
• SolutionSolution: (continued): (continued)
• Good News: ZGood News: Zinin may be calculated or checked may be calculated or checked by MATLAB Zx on a lossless line to save complex by MATLAB Zx on a lossless line to save complex arithmetic labor and show a graphical result!arithmetic labor and show a graphical result!
00
0
o
cos( ) sin( )f)
cos( ) sin( )
150cos(.8 ) 300sin(.8 )(300 )
300cos(.8 ) 150sin(.8 )
510 23.8 (466 206) a cap. impedance
Lin
L
in
Z l jZ lZ Z
Z l jZ l
jZ
j
j
T-line Problem: Example BT-line Problem: Example B
• SolutionSolution: (continued): (continued)
22 9
1 2
2
6 Vf) 7.56 nA .263 rad
(300 466 206)
1 1Re{ } 7.65 10 A 466 13.3 fW
2 2g) (due to lossless line)
but 6.67 fW each2
1h) since where 1 or
2
sin
G in
in in in
L in
LL L
LiLi
ini
VI
Z Z j
P I Z
P P
PP P
VP i
R
2 1 1
2 for either of the two Rx's
then 2.0 V each (vs. 3.0 V w/single Rx)L L in LV V R P
T-line Problem: Example BT-line Problem: Example B
• SolutionSolution: (continued): (continued)
• Check with the graphical output of MATLAB Check with the graphical output of MATLAB ZxZx
max
max
min max
min
1 1i) ( 2 ) ( 0,1, 2,...) where
2 3
and 0.8 0.625 m and -1.875 m
( .25 ) and ( .75 )
j) locations are 0.625 m from positions4
0 and 1.25 m (
j jz m m e e
z
z z
z
only due to 2-m length of line)
T-line Problem: Example BT-line Problem: Example B• SolutionSolution: (note that for all real, resistive Z: (note that for all real, resistive ZLL & Z & Z00))
– The voltage min. occurs @ load if ZThe voltage min. occurs @ load if ZLL<Z<Z0 0
– The voltage max. occurs @ load if ZThe voltage max. occurs @ load if ZLL>Z>Z00
• For the phase of the voltage at the input versus the load For the phase of the voltage at the input versus the load
min
max min
k) 2.0 V
and ( ) (2)(2.0 V) 4.0 VLV V
V VSWR V
9
o
0
0
o0
(7.56 10 A .263 rad)(510 .415 rad)
3.85 V .152 rad 3.85 V 8.7
but anywhere on the line: ( ) ( )
so @ the input ( ): ( ) ( )
3.0 V 72
and @
in in in
j z j z
j l j lin
V I Z
V z e e V
z l V V l e e V
V
o
0
o o
the output ( 0) : (0) (1 ) 2.0 V 288
the reflected wave causes and to differ by 279 vs. 288
L
L in
z V V V
V V
T-line Problem: Example CT-line Problem: Example C
T-line Problem: Example CT-line Problem: Example C(based on Ex. 11.8, H&B, 7/e, p. (based on Ex. 11.8, H&B, 7/e, p.
363)363)• GivenGiven: same T-line but add –j300: same T-line but add –j300 at load at load
• FindFind: : , VSWR, Z, VSWR, Zinin, I, Iinin, P, PLL
• SolutionSolution: now Z: now ZLL = (150 = (150))(–j300(–j300) )
o0
0
o
(150 )( 300 )(120 60)
(150 300)
120 60 300a) .447 153.4
120 60 300
1 1 .447b) 2.62
1 1 .447
c) (755 138.5) 767.5 10.4 (e.g., from MATLAB ZX)
L
L
L
in
jZ j
j
Z Z j
Z Z j
VSWR
Z j
T-line Problem: Example CT-line Problem: Example C
• SolutionSolution: : (continued)(continued)
o
2 2
1 2
6.0 Vd)
[300 (755 138.5)]
5.64 nA 7.5
1 1e) Re{ } (5.64 nA) (755 )
2 212 fW
12 fWwhere and 6 fW
2 2
sin
G in
in in in
LL in L L
VI
Z Z j
P I Z
PP P P P
T-line Problem: Example DT-line Problem: Example D
T-line Problem: Example DT-line Problem: Example D (based on Ex. 11.9, H&B, 7/e, pp. 363, (based on Ex. 11.9, H&B, 7/e, pp. 363,
364)364)• GivenGiven:: same T-line as before but now use same T-line as before but now use
the the purely capacitive load Zpurely capacitive load ZLL = - = -j300j300
• FindFind: : , VSWR, Z, VSWR, Zin in SolutionSolution::o0
0
300 300a) 1 1 90 (total reflection)
300 300
1 1 1b) ( pure standing waves)
1 1 1
c) 589 (purely inductive reactance)
No real power can be delivered to this input
L
L
in
Z Z jj
Z Z j
VSWR
Z j
impedance by the source,
nor can any average power be delivered to the load!
T-line Problem: Example ET-line Problem: Example E (based on D11.4&5, H&B, 7/e, p. (based on D11.4&5, H&B, 7/e, p.
364)364)• GivenGiven: a 50-: a 50- lossless line, lossless line, l l = 0.4= 0.4 long, long,
operating at 300 MHz with Zoperating at 300 MHz with ZLL = 40+j30 = 40+j30 connected at z = 0, and a Thevenin Equiv. connected at z = 0, and a Thevenin Equiv. source of 12esource of 12ej0j0 V at z = - V at z = -l l in series with in series with ZZThTh== 50+j0 50+j0
• FindFind: : , VSWR, Z, VSWR, Zinin, V, Vinin, V, VLL, P, PLL
• SolutionSolution::
o0
0
o
1(40 30) 50 1 1 1 1/ 3 4 / 3a) 90 b) 2
(40 30) 50 3 3 1 1 1/ 3 2 / 3
2c) = 0.4 0.8 rad 144 (25.5 5.90) (e.g., from MATLAB Zx)
L
L
in
Z Z jj s VSWR
Z Z j
l Z j
T-line Problem: Example ET-line Problem: Example E
• Solution: Solution: (continued)(continued) o
o
0
o0
o0
(12 V 0 )(25.5 5.90) d)
(50 0) (25.5 5.90)
4.15 V 8.6
e) also ( ) ( )
6.00 144
@ the load ( 0) : (0) (1 ) 6.33 V 126
and di
ffer by +2.1
Th inin
Th in
j l j lin
L
L in
V Z jV
Z Z j j
V V l e e V
V
z V V V
V V
o8 V in magnitude and +18 in phase
T-line Problem: Example ET-line Problem: Example E
• Solution: Solution: (continued)(continued)
o o
o
o
2 2
f) to calculate average power at the load we can use
6.33 V 126 6.33 V 126
(40 30) 50 36.9
127 mA 163
1 1Re{ } (.127 A) (40 )
2 2.32 W 320 mW
LL
L
L L L
VI
Z j
P I Z
Methods of Solving T-line Methods of Solving T-line ProblemsProblems
• Analytical Expressions (as illustrated here)Analytical Expressions (as illustrated here)+ No special tools needed other than calculator+ No special tools needed other than calculator– Complex number calc’s may become tediousComplex number calc’s may become tedious
• Software ToolsSoftware Tools1) MATLAB Zx for lossless lines (have access)1) MATLAB Zx for lossless lines (have access)
2) Other commercial programs for calc. & sim.2) Other commercial programs for calc. & sim.
• Graphical Tools: Smith ChartGraphical Tools: Smith Chart
ConclusionsConclusions
• Practical T-line problems must address Practical T-line problems must address both source and load conditions; if fully both source and load conditions; if fully unmatched, reflections occur at both unmatched, reflections occur at both ends.ends.
• Input impedance (ZInput impedance (Zinin) is the complex ) is the complex wave impedance at the source end of wave impedance at the source end of the T-line evaluated by analytical the T-line evaluated by analytical formula, MATLAB, other software tools or formula, MATLAB, other software tools or the Smith Chart.the Smith Chart.
ConclusionsConclusions
• The input impedance (ZThe input impedance (Zinin) reduces any ) reduces any sourced and loaded T-line to an equivalent sourced and loaded T-line to an equivalent circuit for the purpose of voltage, current and circuit for the purpose of voltage, current and power analysis. power analysis.
• Certain T-line lengths (Certain T-line lengths (ll) transform the load ) transform the load impedance (Zimpedance (ZLL) at the input in a special way ) at the input in a special way
– QWT: QWT: l l == /4 /4 Z Zinin = Z = Z0022/Z/ZL L (good for matching)(good for matching)
– HWT: HWT: l l == /2 /2 Z Zinin = Z = ZL L (good for transparency)(good for transparency)
ConclusionsConclusions• To find average power delivered to the To find average power delivered to the
load (Pload (PLL) of a sourced and loaded T-line ) of a sourced and loaded T-line – If one knows theIf one knows the
•Thevenin equivalent source (VThevenin equivalent source (Vthth, Z, Zthth))•Characteristic Line & Load impedances (ZCharacteristic Line & Load impedances (Z00,, ZZLL) ) •T-line length, frequency & prop. velocity (T-line length, frequency & prop. velocity (ll, f, v, f, vpp))
– then one can calculatethen one can calculate•T-line electrical length (T-line electrical length ( = = ll))• Input impedance (ZInput impedance (Zinin))•Power input (PPower input (Pinin) via equivalent circuit at the ) via equivalent circuit at the
source and real power absorbed in the load source and real power absorbed in the load
ConclusionsConclusions
• If the If the loadload is not matched to a T-line, is not matched to a T-line, some power reflects back to the source some power reflects back to the source and may damage a generator if and may damage a generator if excessiveexcessive
• If the If the sourcesource is not matched to a T-line is not matched to a T-line (not addressed in examples here!), (not addressed in examples here!), power may reflect at both ends and power may reflect at both ends and calculations become more involvedcalculations become more involved
ReferencesReferences• Hayt & Buck, Hayt & Buck, Engineering Engineering
ElectromagneticsElectromagnetics, 7/e, McGraw Hill: , 7/e, McGraw Hill: New York, 2006.New York, 2006.
• Kraus & Fleisch, Kraus & Fleisch, Electromagnetics Electromagnetics with Applicationswith Applications, 5/e, McGraw Hill: , 5/e, McGraw Hill: New York, 1999.New York, 1999.