Please read the instructions thoroughly before attempting to fit the product or attach it to your electrical system.Please ensure that you use the correct size of electrical element for your towel rail. This product must be fitted by a competent person and in accordance with IEE and local authority regulations. Ensure the mains electrical circuit and the fused spur unbathroom Zone 1. WIRING INSTRUCTIONS A fused spur is required in the supply circuit to the controller, fitted with the correct size fuse. The 2 x E (Earth) & 2 x N (Neutral) terminals are linked on the printed circuit board.

ELECTRICAL ELEMENT WIRES (OUT)

MAINS CABLE WIRES (IN)

ELEMENT

MAINS

1 2 3 4 5 6

1 2 3 4 5 6

Please read the instructions thoroughly before attempting to fit the product or attach it to your electrical system.Please ensure that you use the correct size of electrical element for your towel rail.

This product must be fitted by a competent person and in accordance with IEE and local authority regulations. Ensure the mains electrical circuit and the fused spur unit are both isolated before fitting. This unit should not be fitted in IEE

A fused spur is required in the supply circuit to the controller, fitted with the correct size fuse. terminals are linked on the printed circuit board.

ELECTRICAL ELEMENT WIRES (OUT) From Left to Right terminals Element cable. The element wires should be connected as follows: Green/Yellow Earth to terminal Blue Neutral to terminal 2Brown Live to terminal 3 VERY IMPORTANT - This unit must be earthed

From Left to Right terminals Mains cable wires. The mains cable wires should be connected as follows;Brown Live to terminal 4 Blue Neutral to terminal 5Green/Yellow Earth to terminal VERY IMPORTANT - This unit must be earthed

Clamp the element cable to the controller.

Carefully fit the control plate into the back box ensuring that no wires are trapped during the siting process. Use the two fixing screws to secure to the back box.

ELECTRICAL ELEMENT WALL

Please read the instructions thoroughly before attempting to fit the product or attach it to your electrical system.

This product must be fitted by a competent person and in accordance with IEE and local authority regulations. Ensure the it are both isolated before fitting. This unit should not be fitted in IEE

A fused spur is required in the supply circuit to the controller, fitted with the correct size fuse.

From Left to Right terminals 1-3 correspond to the

should be connected as follows:

to terminal 1 (E on board) 2 (LO on board) (AD/T on board)

This unit must be earthed

From Left to Right terminals 4-6 correspond to the

wires should be connected as follows; (L on board)

5 (N on board) to terminal 6 (E on board)

This unit must be earthed

Clamp the element cable to the bottom of the wall

Carefully fit the control plate into the back box ensuring that no wires are trapped during the siting process.

crews to secure to the back box.

ELECTRICAL ELEMENT WALL CONTROLLER

BASIC OPERATION The Power Button cycles the unit between standby Press the Power Button and the power LED will turn Press the +/- buttons to increase or decrease the Each one of the ORANGE LEDs represents the following power output from the element:5 LEDs = 100% power > 4 LEDs = 85% powerTo switch off/enter standby, press the Power B NOTE: The wall controller has a memory anthe unit is turned on again. ECO FUNCTION The ECO function operates the wall contminutes. (The final 90 minutes must be equal to or lower than the initial Press the Power Button and the power LED will Use the +/- buttons to set the required power level for the final 90 minutes of operationPress the ECO Button and the power LED will turn Use the +/- buttons to set the required power level for the initialThe wall controller will now be on for 30 minutes at the level just set. After 30 minutes the power LED will turn the wall controller will operate for the final 90 minuAfter 90 minutes the power LED will turn Technical Data. Ingress protection: IPX4 Voltage: 230-245 V Maximum power output: 800w Dimensions: 85 x 85 x 20mm Approvals: CE, tested to EN55014-1:2006

(2)

(3)(1)

(4)

© Copyright Kudox Limited 2014

The Power Button cycles the unit between standby mode (BLUE LED) and on (RED LED).LED will turn RED with the ORANGE LEDs showing the power setting.

o increase or decrease the towel rail surface temperature. represents the following power output from the element:

4 LEDs = 85% power > 3 LEDs = 70% power > 2 LEDs = 55% power /enter standby, press the Power Button to make the power LED BLUE.

a memory and the temperature set before the unit entered standby will be resumed when

ECO function operates the wall controller for 2 hours at a power for the initial 30 minutes higher than the final 90 must be equal to or lower than the initial 30 minute level).

utton and the power LED will turn RED. buttons to set the required power level for the final 90 minutes of operation.

utton and the power LED will turn GREEN. buttons to set the required power level for the initial 30 minutes of operation.

The wall controller will now be on for 30 minutes at the level just set. After 30 minutes the power LED will turn the wall controller will operate for the final 90 minutes at the equal or lower level.

LED will turn BLUE and the wall controller has switched off.

For technical support please call 020 75899617 or visit

1:2006 Kudox Limited 1 Bray Place SW3 3

(2)

(3)

OPERATING INSTRUCTIONS There are four buttons on the control plate: (1) Power Button (2) Temperature Increase (3) Temperature Decrease (4) ECO Button

LED). showing the power setting.

2 LEDs = 55% power > 1 LED = 40% power

entered standby will be resumed when

or the initial 30 minutes higher than the final 90

The wall controller will now be on for 30 minutes at the level just set. After 30 minutes the power LED will turn RED and

For technical support please call or visit www.kudox.com

Kudox Limited 1 Bray Place SW3 3LL

ur buttons on the control plate:

Version 1.01 20141024