EDGE KPI.pdf

GSM/EDGE BSS, Rel. RG10(BSS), Operating Documentation, Issue 08

Reference

76 Dynamic Abis Measurement

DN00209137

Issue 6-0Approval Date 12/02/2009 00:00:00

Confidential

2 DN00209137Issue 6-0


Id:0900d805805a391eConfidential

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given "as is" and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL Nokia Siemens Networks BE LIABLE FOR ERRORS IN THIS DOCUMENTA-TION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDI-RECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only.

Copyright © Nokia Siemens Networks 2011. All rights reserved

f Important Notice on Product SafetyThis product may present safety risks due to laser, electricity, heat, and other sources of danger.

Only trained and qualified personnel may install, operate, maintain or otherwise handle this product and only after having carefully read the safety information applicable to this product.

The safety information is provided in the Safety Information section in the “Legal, Safety and Environmental Information” part of this document or documentation set.

The same text in German:

f Wichtiger Hinweis zur Produktsicherheit Von diesem Produkt können Gefahren durch Laser, Elektrizität, Hitzeentwicklung oder andere Gefahrenquellen ausgehen.

Installation, Betrieb, Wartung und sonstige Handhabung des Produktes darf nur durch geschultes und qualifiziertes Personal unter Beachtung der anwendbaren Sicherheits-anforderungen erfolgen.

Die Sicherheitsanforderungen finden Sie unter „Sicherheitshinweise“ im Teil „Legal, Safety and Environmental Information“ dieses Dokuments oder dieses Dokumentations-satzes.

DN00209137 3



Table of contentsThis document has 22 pages.

Summary of changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 76 Dynamic Abis Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Counters of Dynamic Abis Measurement . . . . . . . . . . . . . . . . . . . . . . . . 82.1 076000 / TOTAL PCM SUBTSLS IN EDAP. . . . . . . . . . . . . . . . . . . . . . . 82.2 076001 / AVERAGE DL EDAP USAGE. . . . . . . . . . . . . . . . . . . . . . . . . . 82.3 076002 / AVERAGE UL EDAP USAGE. . . . . . . . . . . . . . . . . . . . . . . . . . 92.4 076003 / AVERAGE EDAP USAGE DEN . . . . . . . . . . . . . . . . . . . . . . . . 92.5 076004 / PEAK DL EDAP USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.6 076005 / PEAK UL EDAP USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.7 076006 / UL TBFS WITHOUT EDAP RES . . . . . . . . . . . . . . . . . . . . . . 112.8 076007 / DL TBFS WITHOUT EDAP RES . . . . . . . . . . . . . . . . . . . . . . 112.9 076008 / DL TBFS WITH INADEQUATE EDAP RES . . . . . . . . . . . . . . 112.10 076009 / UL EDAP ALLOCATION REQUESTS . . . . . . . . . . . . . . . . . . 122.11 076010 / DL EDAP ALLOCATION REQUESTS . . . . . . . . . . . . . . . . . . 122.12 076011 / AVE EDAP UL ALLOCATED FOR RT . . . . . . . . . . . . . . . . . . 132.13 076012 / AVE EDAP DL ALLOCATED FOR RT . . . . . . . . . . . . . . . . . . 132.14 076013 / AVE EDAP UL USAGE FOR RT . . . . . . . . . . . . . . . . . . . . . . 142.15 076014 / AVE EDAP DL USAGE FOR RT . . . . . . . . . . . . . . . . . . . . . . 142.16 076015 / AVE EDAP UL USAGE FOR NRT . . . . . . . . . . . . . . . . . . . . . 142.17 076016 / AVE EDAP DL USAGE FOR NRT . . . . . . . . . . . . . . . . . . . . . 152.18 076017 / TOT NBR OF PCM STS IN EDAP UL . . . . . . . . . . . . . . . . . . 152.19 076018 / DYNAMIC ABIS DENOM UL . . . . . . . . . . . . . . . . . . . . . . . . . 162.20 076019 / UL MCS LIMITED BY PCU. . . . . . . . . . . . . . . . . . . . . . . . . . . 162.21 076020 / DL MCS LIMITED BY PCU. . . . . . . . . . . . . . . . . . . . . . . . . . . 172.22 076021 / TIMES OVER DL EDAP LOW THRESHOLD. . . . . . . . . . . . . 172.23 076022 / TIMES OVER DL EDAP HIGH THRESHOLD . . . . . . . . . . . . 182.24 076023 / TIMES OVER UL EDAP LOW THRESHOLD. . . . . . . . . . . . . 182.25 076024 / TIMES OVER UL EDAP HIGH THRESHOLD . . . . . . . . . . . . 192.26 076025 / EDAP SLAVE CHANNEL REQUESTED DL . . . . . . . . . . . . . 192.27 076026 / EDAP SLAVE CHANNEL REQUESTED UL . . . . . . . . . . . . . 202.28 076027 / EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO

SMALL DL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202.29 076028 / EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO

SMALL UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.30 076029 / EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON

DL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.31 076030 / EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON

UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4 DN00209137



List of tablesTable 1 Measurement description of Dynamic Abis Measurement . . . . . . . . . . . . 6Table 2 Counters of Dynamic Abis Measurement . . . . . . . . . . . . . . . . . . . . . . . . 6

DN00209137 5

76 Dynamic Abis Measurement Summary of changes

Id:0900d805805a3915Confidential

Summary of changesChanges between document issues are cumulative. Therefore, the latest document issue contains all changes made to previous issues.

Changes made between issues 6-0 and 5-1NetAct names corrected in counter tables.

Changes made between issues 5-1 and 5-0Counters 076001 and 076002 modified.

Changes made between issues 5-0 and 4-0New counters 076021 - 076030 related to BSS20432: Packet Data Optimisation Package added.

Counter table format changed.

6 DN00209137




1 76 Dynamic Abis MeasurementDynamic Abis Measurement provides information on the usage of EDAP both in uplink and downlink directions.

This measurement is optional.

Measurement description

Measurement counters

MeasurementMeasurement IDMeasurement abbreviation

Dynamic Abis Measurement76DYNAMIC_ABIS

Product BSC

Product software release S10

Target name Abis pool

Table 1 Measurement description of Dynamic Abis Measurement

Counter Counter number

TOTAL PCM SUBTSLS IN EDAP 076000

AVERAGE DL EDAP USAGE 076001

AVERAGE UL EDAP USAGE 076002

AVERAGE EDAP USAGE DEN 076003

PEAK DL EDAP USAGE 076004

PEAK UL EDAP USAGE 076005

UL TBFS WITHOUT EDAP RES 076006

DL TBFS WITHOUT EDAP RES 076007

DL TBFS WITH INADEQUATE EDAP RES 076008

UL EDAP ALLOCATION REQUESTS 076009

DL EDAP ALLOCATION REQUESTS 076010

AVE EDAP UL ALLOCATED FOR RT 076011

AVE EDAP DL ALLOCATED FOR RT 076012

AVE EDAP UL USAGE FOR RT 076013

AVE EDAP DL USAGE FOR RT 076014

AVE EDAP UL USAGE FOR NRT 076015

AVE EDAP DL USAGE FOR NRT 076016

TOT NBR OF PCM STS IN EDAP UL 076017

DYNAMIC ABIS DENOM UL 076018

UL MCS LIMITED BY PCU 076019

DL MCS LIMITED BY PCU 076020

Table 2 Counters of Dynamic Abis Measurement

DN00209137 7

76 Dynamic Abis Measurement 76 Dynamic Abis Measurement


Related topics

• Counters of Dynamic Abis Measurement

Instructions

• BSC Statistics AdministrationFor information on using this measurement to test the activation of related software, see the testing instructions in:

• Activating and Testing BSS10083: EGPRS

Reference

• BSC Measurement Counters Displaying Program (FOXMEA) • Performance Measurements • PCU2 Service Terminal Commands

Descriptions

• Dynamic Abis in BSC • GPRS/EDGE System Feature Description

TIMES OVER DL EDAP LOW THRESHOLD 076021

TIMES OVER DL EDAP HIGH THRESHOLD 076022

TIMES OVER UL EDAP LOW THRESHOLD 076023

TIMES OVER UL EDAP HIGH THRESHOLD 076024

EDAP SLAVE CHANNEL REQUESTED DL 076025

EDAP SLAVE CHANNEL REQUESTED UL 076026

EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL DL

076027

EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL UL

076028

EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON DL

076029

EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON UL

076030

Counter Counter number

Table 2 Counters of Dynamic Abis Measurement (Cont.)

8 DN00209137


Id:0900d805805a391bConfidential

Counters of Dynamic Abis Measurement

2 Counters of Dynamic Abis Measurement

2.1 076000 / TOTAL PCM SUBTSLS IN EDAP

2.2 076001 / AVERAGE DL EDAP USAGE

Counter ID: 076000 Network element name: TOTAL PCM SUBTSLS IN EDAP

Version: 3.0 NetAct name: TOTAL_PCM_SUBTSLS_IN_EDAP

Description: Total number of 16kbit/s PCM subTSLs in the Dynamic Abis Pool.This counter is updated along with counters 076001 and 076003.

Updated: When DL Dynamic Abis resource allocation occurs. The counter is incremented by the size of the Dynamic Abis Pool.

Logical type: Sum Trigger type: Event Sampling interval:

Unit: Integer number Range: Example values:

Dependencies with other counters:

076001: AVERAGE DL EDAP USAGE

076003: AVERAGE EDAP USAGE DEN

Operability class:

Related to feature:

BSS115171: Dynamic Abis Enhancements

BSS10045: Dynamic Abis

Related to standard:

3GPP Measurement name (Clause header):

3GPP Measurement type:

Exceptions to related standard:

Used from release: S10 Definition updated in release:

Counter ID: 076001 Network element name: AVERAGE DL EDAP USAGE

Version: 3.1 NetAct name: AVERAGE_DL_EDAP_USAGE_SUM

Description: This counter sums up the sampled values of reserved 16 kbit/s subTSLs in downlink. The number of the samples is stored in counter 076003.

Updated: When DL Dynamic Abis resource allocation occurs. The counter is incremented by the value of reserved 16 kbit/s subTSLs in downlink.




076003: AVERAGE EDAP USAGE DEN

Operability class:

Related to feature:





DN00209137 9

76 Dynamic Abis Measurement Counters of Dynamic Abis Measurement


2.3 076002 / AVERAGE UL EDAP USAGE

2.4 076003 / AVERAGE EDAP USAGE DEN


Used from release: S10 Definition updated in release: S13

Counter ID: 076002 Network element name: AVERAGE UL EDAP USAGE

Version: 3.1 NetAct name: AVERAGE_UL_EDAP_USAGE_SUM

Description: This counter sums up the sampled values of reserved 16 kbit/s subTSLs in uplink. The number of the samples is stored in counter 076018.

Updated: When UL Dynamic Abis resource allocation occurs. The counter is incremented by the value of reserved 16 kbit/s subTSLs in uplink.




076018: DYNAMIC ABIS DENOM UL

Operability class:

Related to feature:






Used from release: S10 Definition updated in release: S13

Counter ID: 076003 Network element name: AVERAGE EDAP USAGE DEN

Version: 3.0 NetAct name: AVERAGE_EDAP_USAGE_DEN

Description: Denominator.This counter is updated along with counters 076000 and 076001.

Updated: When DL Dynamic Abis resource allocation occurs. Counter is incremented by 1 in every trans-mission turn.




076000: TOTAL PCM SUBTSLS IN EDAP

076001: AVERAGE DL EDAP USAGE

Operability class:

Related to feature:





10 DN00209137




2.5 076004 / PEAK DL EDAP USAGE

2.6 076005 / PEAK UL EDAP USAGE




Counter ID: 076004 Network element name: PEAK DL EDAP USAGE

Version: 3.0 NetAct name: PEAK_DL_EDAP_USAGE

Description: Peak usage of used 16 kbit/s PCM subTSLs in downlink direction. The value is given as per-centage from the total amount of subTSLs in DL EDAP.

Updated: When Dynamic Abis resource allocation occurs.

Logical type: Max Trigger type: Event Sampling interval:

Unit: % Range: Example values:


Operability class:

Related to feature:







Counter ID: 076005 Network element name: PEAK UL EDAP USAGE

Version: 3.0 NetAct name: PEAK_UL_EDAP_USAGE

Description: Peak usage of used 16 kbit/s PCM subTSLs in uplink direction. The value is given as per-centage from the total amount of subTSLs in UL EDAP.

Updated: When Dynamic Abis resource allocation occurs.

Logical type: Max Trigger type: Event Sampling interval:

Unit: % Range: Example values:


Operability class:

Related to feature:







DN00209137 11



2.7 076006 / UL TBFS WITHOUT EDAP RES

2.8 076007 / DL TBFS WITHOUT EDAP RES

2.9 076008 / DL TBFS WITH INADEQUATE EDAP RES

Counter ID: 076006 Network element name: UL TBFS WITHOUT EDAP RES

Version: 3.0 NetAct name: UL_TBFS_WITHOUT_EDAP_RES

Description: Number of cases where scheduled UL TBF cannot be serviced because of a lack of EDAP resources.

Updated: Every time UL TBF is left without Dynamic Abis service.




Operability class:

Related to feature:







Counter ID: 076007 Network element name: DL TBFS WITHOUT EDAP RES

Version: 3.0 NetAct name: DL_TBFS_WITHOUT_EDAP_RES

Description: Number of cases where no EDAP channels can be given to a downlink TBF and only the EDGE master channel is granted.

Updated: Every time DL TBF is left without Dynamic Abis service.




Operability class:

Related to feature:







Counter ID: 076008 Network element name: DL TBFS WITH INADEQUATE EDAP RES

12 DN00209137




2.10 076009 / UL EDAP ALLOCATION REQUESTS

2.11 076010 / DL EDAP ALLOCATION REQUESTS

Version: 3.0 NetAct name: DL_TBFS_WITH_INADEQ_EDAP_RES

Description: Number of cases where required EDAP channels cannot be granted to DL TBF and it is serviced with reduced number of EDAP channels in addition to the EGPRS master channel.

Updated: Every time DL TBF is serviced with reduced number of channels.




Operability class:

Related to feature:







Counter ID: 076009 Network element name: UL EDAP ALLOCATION REQUESTS

Version: 3.0 NetAct name: UL_EDAP_ALLOCATION_REQUESTS

Description: Number of UL EDAP allocation requests.

Updated: At every scheduling round for every TSL where radio blocks are to be transferred.




Operability class:

Related to feature:

BSS115172: PCU Measurement Enhancements





Used from release: S11.5 Definition updated in release:

Counter ID: 076010 Network element name: DL EDAP ALLOCATION REQUESTS

Version: 3.0 NetAct name: DL_EDAP_ALLOCATION_REQUESTS

Description: Number of DL EDAP allocation requests.

Updated: At every scheduling round for every TSL where radio blocks are to be transferred.


DN00209137 13



2.12 076011 / AVE EDAP UL ALLOCATED FOR RT

2.13 076012 / AVE EDAP DL ALLOCATED FOR RT



Operability class:

Related to feature:

BSS115172: PCU Measurement Enhancements






Counter ID: 076011 Network element name: AVE EDAP UL ALLOCATED FOR RT

Version: 3.1 NetAct name: AVE_EDAP_UL_ALLOCATED_FOR_RT

Description: This counter is not in use.

Updated: This counter is not updated.

Logical type: Trigger type: Sampling interval:

Unit: Range: Example values:


Operability class:

Related to feature: Related to standard:




Used from release: S11.5 Definition updated in release: S12

Counter ID: 076012 Network element name: AVE EDAP DL ALLOCATED FOR RT

Version: 3.1 NetAct name: AVE_EDAP_DL_ALLOCATED_FOR_RT






Operability class:




14 DN00209137




2.14 076013 / AVE EDAP UL USAGE FOR RT

2.15 076014 / AVE EDAP DL USAGE FOR RT

2.16 076015 / AVE EDAP UL USAGE FOR NRT



Counter ID: 076013 Network element name: AVE EDAP UL USAGE FOR RT

Version: 3.1 NetAct name: AVE_EDAP_UL_USAGE_FOR_RT






Operability class:






Counter ID: 076014 Network element name: AVE EDAP DL USAGE FOR RT

Version: 3.1 NetAct name: AVE_EDAP_DL_USAGE_FOR_RT






Operability class:






Counter ID: 076015 Network element name: AVE EDAP UL USAGE FOR NRT

Version: 3.1 NetAct name: AVE_EDAP_UL_USAGE_FOR_NRT

DN00209137 15



2.17 076016 / AVE EDAP DL USAGE FOR NRT

2.18 076017 / TOT NBR OF PCM STS IN EDAP UL






Operability class:






Counter ID: 076016 Network element name: AVE EDAP DL USAGE FOR NRT

Version: 3.1 NetAct name: AVE_EDAP_DL_USAGE_FOR_NRT






Operability class:






Counter ID: 076017 Network element name: TOT NBR OF PCM STS IN EDAP UL

Version: 3.0 NetAct name: TOT_NBR_OF_PCM_STS_IN_EDAP_UL

Description: Total number of 16 kbit/s PCM subtimeslots in EDAP. Sum of samples.Dependency: 076018 DYNAMIC ABIS DENOM UL

Updated: When UL Dynamic Abis resource allocation occurs. The counter is incremented by the size of the Dynamic Abis Pool.




076018: DYNAMIC ABIS DENOM UL

16 DN00209137




2.19 076018 / DYNAMIC ABIS DENOM UL

2.20 076019 / UL MCS LIMITED BY PCU

Operability class:

Related to feature:







Counter ID: 076018 Network element name: DYNAMIC ABIS DENOM UL

Version: 3.0 NetAct name: DYNAMIC_ABIS_DENOM_UL

Description: Denominator.Dependencies: 076017 TOT NBR OF PCM STS IN EDAP UL, 076002 AVERAGE UL EDAP USAGE

Updated: When UL Dynamic Abis resource allocation occurs. The counter is incremented by 1 in each transmission turn.




076002: AVERAGE UL EDAP USAGE

076017: TOT NBR OF PCM STSIN EDAP UL

Operability class:

Related to feature:







Counter ID: 076019 Network element name: UL MCS LIMITED BY PCU

Version: 3.0 NetAct name: UL_MCS_LIMITED_BY_PCU

Description: Number of cases when MCS has been limited by the PCU (for example, DSP resources) in uplink scheduling.

Updated: When MCS is limited in UL scheduling.




Operability class:

DN00209137 17



2.21 076020 / DL MCS LIMITED BY PCU

2.22 076021 / TIMES OVER DL EDAP LOW THRESHOLD

Related to feature:







Counter ID: 076020 Network element name: DL MCS LIMITED BY PCU

Version: 3.0 NetAct name: DL_MCS_LIMITED_BY_PCU

Description: Number of cases when MCS has been limited by the PCU (for example, DSP resources) in downlink scheduling.

Updated: When MCS is limited in UL scheduling.




Operability class:

Related to feature:







Counter ID: 076021 Network element name: TIMES OVER DL EDAP LOW THRESHOLD

Version: 2.0 NetAct name: TIMES_OVER_DL_EDAP_LOW_THR

Description: Number of 20 ms periods when the DL EDAP load was above the low threshold parameter value.

Updated: When the current EDAP load is above the low threshold parameter value. The current EDAP load is checked against the low EDAP load threshold parameter every time the EDAP allocation is made.This counter is updated for PCU2 only.


Unit: 20 ms Range: Example values:


076022: TIMES OVER DL EDAP HIGH THRESHOLD

Operability class:

18 DN00209137




2.23 076022 / TIMES OVER DL EDAP HIGH THRESHOLD

2.24 076023 / TIMES OVER UL EDAP LOW THRESHOLD

Related to feature:

BSS20432: Packet Data Optimisation Package






Counter ID: 076022 Network element name: TIMES OVER DL EDAP HIGH THRESHOLD

Version: 2.0 NetAct name: TIMES_OVER_DL_EDAP_HIGH_THR

Description: Number of 20 ms periods when the DL EDAP load was above the high threshold parameter value.

Updated: When the current EDAP load is above the high threshold parameter value. The current EDAP load is checked against the high EDAP load threshold parameter every time the EDAP allocation is made. This counter is updated for PCU2 only.




Operability class:

Related to feature:







Counter ID: 076023 Network element name: TIMES OVER UL EDAP LOW THRESHOLD

Version: 2.0 NetAct name: TIMES_OVER_UL_EDAP_LOW_THR

Description: Number of 20 ms periods when the UL EDAP load was above the low threshold parameter value.

Updated: When the current EDAP load is above the low threshold parameter value. The current EDAP load is checked against the low EDAP load threshold parameter every time the EDAP allocation is made.This counter is updated for PCU2 only.




076024: TIMES OVER UL EDAP HIGH THRESHOLD

DN00209137 19



2.25 076024 / TIMES OVER UL EDAP HIGH THRESHOLD

2.26 076025 / EDAP SLAVE CHANNEL REQUESTED DL

Operability class:

Related to feature:







Counter ID: 076024 Network element name: TIMES OVER UL EDAP HIGH THRESHOLD

Version: 2.0 NetAct name: TIMES_OVER_UL_EDAP_HIGH_THR

Description: Number of 20 ms periods when the UL EDAP load was above the high threshold parameter value.

Updated: When the current EDAP load is above the high threshold parameter value. The current EDAP load is checked against the high EDAP load threshold parameter every time the EDAP allocation is made. This counter is updated for PCU2 only.




Operability class:

Related to feature:







Counter ID: 076025 Network element name: EDAP SLAVE CHANNEL REQUESTED DL

Version: 2.0 NetAct name: EDAP_SLAVE_CH_REQUESTED_DL

Description: Number of EDAP slave channels that are requested for DL allocation.

Updated: With the number of requested slave channels at every DL EDAP request where also the slave channels are requested.This counter is updated for PCU2 only.




Operability class:

20 DN00209137




2.27 076026 / EDAP SLAVE CHANNEL REQUESTED UL

2.28 076027 / EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL DL

Related to feature:







Counter ID: 076026 Network element name: EDAP SLAVE CHANNEL REQUESTED UL

Version: 2.0 NetAct name: EDAP_SLAVE_CH_REQUESTED_UL

Description: Number of EDAP slave channels that are requested for UL allocation.

Updated: With the number of requested slave channels at every UL EDAP request where also the slave channels are requested.This counter is updated for PCU2 only.




Operability class:

Related to feature:







Counter ID: 076027 Network element name: EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL DL

Version: 2.0 NetAct name: NO_EDAP_SLAVE_CH_DUE_SIZE_DL

Description: Number of EDAP slave DL channels that could not be allocated because the EDAP size was too small.

Updated: When the DL channel allocation is smaller than the requested due to the EDAP capacity.This counter is updated for PCU2 only.




Operability class:

DN00209137 21



2.29 076028 / EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL UL

2.30 076029 / EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON DL

Related to feature:







Counter ID: 076028 Network element name: EDAP MISSING SLAVE CHANNEL DUE TO EDAP SIZE TOO SMALL UL

Version: 2.0 NetAct name: NO_EDAP_SLAVE_CH_DUE_SIZE_UL

Description: Number of EDAP slave UL channels that could not be allocated because the EDAP size was too small.

Updated: When the UL channel allocation is smaller than the requested due to the EDAP capacity.This counter is updated for PCU2 only.




Operability class:

Related to feature:







Counter ID: 076029 Network element name: EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON DL

Version: 2.0 NetAct name: NO_EDAP_SLAVE_CH_DUE_OTH_DL

Description: Number of EDAP slave DL channels that could not be allocated because of any other reason than EDAP size (for example, DSP channels not available).

Updated: When the DL channel allocation is smaller than the requested due to other reasons than the EDAP size.This counter is updated for PCU2 only.




22 DN00209137




2.31 076030 / EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON UL

Operability class:

Related to feature:







Counter ID: 076030 Network element name: EDAP MISSING SLAVE CHANNEL DUE TO OTHER REASON UL

Version: 2.0 NetAct name: NO_EDAP_SLAVE_CH_DUE_OTH_UL

Description: Number of EDAP slave UL channels that could not be allocated because of any other reason than EDAP size (for example, DSP channels not available).

Updated: When the UL channel allocation is smaller than the requested due to other reasons than the EDAP size.This counter is updated for PCU2 only.




Operability class:

Related to feature:







Documents

EDGE KPI.pdf