ED. Larius 4 Transferlarius.org/manuali/LARIUS4_UK.pdf · LARIUS 4 - TRAnSfeR eD. 04 - 06/2020 - Cod. 150147 5 WARNINGS The table below provides the meaning of the symbols used in

www. l a r i u s . com

ED. 0

4 -

06/2

020

Man

uale

Cod

. 150

147

II 2 G c IIB T4

Larius 4Transfer

Pneumatic double diaphragm pump

OP

ER

ATIN

G A

ND

MA

INTE

NA

NC

E M

AN

UA

L

EN

LARIUS 4 - TRAnSfeR

www.larius.com2 ED. 04 - 06/2020 - Cod. 150147

Due to a constant product improvement programme, the factory reserves the right to modifytechnical details mentioned in this manual without prior notice.

This manual is to be considered as an English language translation of the original manual in Italian.The manufacturer shall bear no responsibility for any damages or inconveniences that may arise due to

the incorrect translation of the instructions contained within the original manual in Italian.

LARIUS 4 - TRAnSfeR

www.larius.com 3ED. 04 - 06/2020 - Cod. 150147

WE ADVISE THE USE OF THIS EQUIPMENT ONLY BY PROFESSIONAL OPERATORS.ONLY USE THIS MACHINE FOR USAGE SPECIFICALLY MENTIONED IN THIS MANUAL.

Thank you for choosing a LARIUS S.R.L. product.As well as the product purchased, you will receive a range of support services

enabling you to achieve the results desired, quickly and professionally.

WARNINGS ............................................................................................................................................................ p. 5

WORKING pRINCIpLE ........................................................................................................................................... p. 6

TECHNICAL DATA .................................................................................................................................................. p. 6

DESCRIpTION OF THE EQUIpMENT .................................................................................................................... p. 8

IDENTIFICATION .................................................................................................................................................... p. 8

TRANSpORT AND UNpACKING ............................................................................................................................ p. 8

SAFETY RULES ...................................................................................................................................................... p. 9

CONDITIONS OF GUARANTEE ............................................................................................................................. p.10

SETTING-Up .......................................................................................................................................................... p.10

WORKING .............................................................................................................................................................. p.11

pROBLEMS AND SOLUTION ................................................................................................................................ p.12

SPARE PARTS

EXpLODED pNEUMATIC MOTOR UNIT VIEW ...................................................................................................... p.14

ATEX ....................................................................................................................................................................... p.16

DECLARATION OF CONFORMITY ......................................................................................................................... p.19

INDEX

A

CD

B

E

HG

F

I

JK

Larius 4TransferPneumatic double diaphragm pump

Inte

ntio

nally

bla

nk p

age

LARIUS 4 - TRAnSfeR


WARNINGS The table below provides the meaning of the symbols used in this manual in relation to using, earthing, operating, maintaining, and repairing of this equipment.

Read this operator’s manual carefully before using the equipment.An improper use of this machine can cause injuries to people or things.Do not use this machine when under the influence of drugs or alcohol.Do not modify the equipment under any circumstances.Use products and solvents that are compatible with the various parts of the equipment, and read the manufacturer’s warnings carefully.See the Technical Details for the equipment given in the Manual.Check the equipment for worn parts once a day. If any worn parts are found, replace them using ONLY original spare parts.Keep children and animals away from work area.Comply with all safety standards.

It indicates an accident risk or serious damage to equipment if this warning is not followed.

It indicates important recommendations about disposal and recycling process of products in accordance with the environmental regulations.

It indicates a fire or explosion risk if this warning is not followed.Eliminate all ignition sources such as pilot lights, cigarettes, portable electric lamps and plastic drop cloths.Keep work area free of debris.ONLY use this equipment in a well ventilated area.EARTH ALL THE EQUIpMENT LOCATED IN THE WORK AREA.Do not form connections or switch light switches on or off if the air contains inflammable fumes.If electrical shocks or discharges are encountered the operation being carried out using the equipment must be stopped immediately.Keep a fire extinguisher at hand in the immediate vicinity of the work area.

It indicates wound and finger squashing risk due to movable parts in the equipment.Tenersi lontano dalle parti in movimento.Do not use the equipment without the proper protection.Before any inspection or maintenance of the equipment, carry out the decompression procedure explained in this manual, and prevent any risk of the equipment starting unexpectedly.

Report any risk of chemical reaction or explosion if this warning has not been given.There is a risk of injury or serious lesion related to contact with the jet from the spray gun. If this should occur, IMMEDIATELY contact a doctor, indicating the type of product injected.Do not spray before the guard has been placed over the nozzle and the trigger on the spray gun.Do not put your fingers in the spray gun nozzle.Once work has been completed, before carrying out any maintenance, complete the decompression procedure explained in this manual.

Report any danger of electric shock if the warning and presence of live electrical parts has not been indicated.Store in a dry place and do not expose to the rain.Check that the cables are in good condition.Switch off the equipment and discharge any electricity before cleaning or maintaining the equipment.

Mark any clamps attached to earth cables.Use ONLY 3-wire extension cords and grounded electrical outlets.Before starting work make sure that the electrical system is earthed and that it complies with safety standards.

It is obligatory to wear suitable clothing as gloves, goggles and face shield.Wear clothing that complies with the safety standards in force in the country in which the equipment is used.Do not wear bracelets, earrings, rings, chains, or anything else that may hinder the operator’s work.Do not wear clothing with wide sleeves, scarves, ties, or any other piece of clothing that could get tangled up in moving parts of the equipment during the work, inspection, or maintenance cycles.

LARIUS 4 - TRAnSfeR


A

8 bar (115 psi)

2-8 bar (30-115 psi)

1/4" GAS (F)

40 l/min

1” GAS (M)

1” GAS (M)

190 l/min (6,7 cfm)

<75 dB (A)

9 kg

LARIUS 4

WORKING PRINCIPLEpneumatic double membrane pumps for industrial pumping of liquids and highly corrosive and aggressive acids.Characterised by their high performance, high power and stur-diness, which make them suitable for pumping liquids with high viscosity, including in the presence of suspended solids. They meet the working needs of the chemical, textile, food, ecologi-cal, graphics, tanning, ceramics, electronics, galvanic, oil, paint, biodiesel, urea pumping and other industries

The compressed air introduced by the pneumatic exchanger behind one of the two diaphragms generates compression and pushes the product into the delivery duct, at the same time, the opposing diaphragm that is integral with the exchanger shaft creates a vacuum and intakes the fluid.

Once the stroke has been completed, the pneumatic exchanger diverts the compressed air behind the opposing diaphragm and the cycle is reversed.

TECHNICAL DATAB

*N.B. The pump is supplied with a bayonet connection.

Parts of the pump in contact with the material In the standard model in Aluminium (code 8000) the parts are made of:Aluminium AISI 12 UNI 5076 - pTFE - Galvanized steel - Stainless steel AISI 316 and AISI 303 - pTFE

In the Stainless steel model (code 8132) they are made of: Stain-less steel AISI 316 and AISI 303 - pTFE

OTHER pARTS OF THE pUMp

pump body: ALUMINIUM

Supporting bracket: GALVANIZED STEEL

Always observe these instructions care-fully when evaluating the product com-patibility and in case of disposal of some parts of the pump no more usable, in order to meet the environmental regulations on recycling process.

MAXIMUM PRESSURE OF THE PRODUCT

PUMP FEED AIR PRESSURE

*FEED AIR INLET

MAXIMUM DELIVERY

MATERIAL INPUT

MATERIAL EXIT

MAXIMUM AIR CONSUMPTION

NOISE PRESSURE LEVEL

wEIgHT

LARIUS 4 - TRAnSfeR


320

390

N. Code

8300

8301

A

Alluminium

Stainless steel

Pump

LARIUS

OUT

IN163÷170

A

10

103

206 215

LARIUS 4 - TRAnSfeR


C

1

2

3

4

5

6

7

POS.

1

2

3

4

5

6

7

Description

Pump feed air pressure regulator

Pump feed air manometer

Air closing cock

Pump feed air inlet

Pump fastening and supporting bracket

Material inlet fitting

Material outlet filling

E

MADE IN ITALYWWW.LARIUS.COM

MODEL

SERIAL NUMBER

YEAROF COSTRUCTION

DESCRIPTION OF THE EQUIPMENT

The LARIUS 4 pump is a double diahragm pneuma-tic pump to be used for transfer of low and medium viscosity fluids.It is essentially composed of two chambers which are placed on suctio and on delivery alternatively thanks to the action of two membranes in pTFE connected to a shaft in reciprocating traverse motion. The reciprocating motion is obtained through a proper compressed air driver reversal device (pilot valve).

TRANSPORT AND UNPACKING• The packed parts should be handled as indicated in the

symbols and markings on the outside of the packing.

• Before installing the equipment, ensure that the area to be used is large enough for such purposes, is properly lit and has a clean, smooth floor surface.

• The user is responsible for the operations of unloading and handling and should use the maximum care so as not to damage the individual parts or injure anyone.

To perform the unloading operation, use only qualified and trained personnel (truck and crane operators, etc.) and also suitable hoisting equipment for the weight of the installation or its parts.

Follow carefully all the safety rules. The personnel must be equipped with the necessary

safety clothing.

• The manufacturer will not be responsible for the unlo-ading operations and transport to the workplace of the machine.

• Check the packing is undamaged on receipt of the equi-pment. Unpack the machine and verify if there has been any damage due to transportation.

In case of damage, call immediately LARIUS and the Shipping Agent. All the notices about possible damage

IDENTIFICATIONDFor communications with LARIUS, always refer to the machine model contained on the identification plate.

LARIUS 4 - TRAnSfeR


F SAFETY RULES• THE EMpLOYER SHALL TRAIN ITS EMpLOYEES

ABOUT ALL THOSE RISKS STEMMING FROM ACCI-DENTS, ABOUT THE USE OF SAFETY DEVICES FOR THEIR OWN SAFETY AND ABOUT THE GENERAL RULES FOR ACCIDENT pREVENTION IN COMpLIAN-CE WITH INTERNATIONAL REGULATIONS AND WITH THE LAWS OF THE COUNTRY WHERE THE pLANT IS USED.

• THE BEHAVIOUR OF THE EMpLOYEES SHALL STRICTLY COMpLY WITH THE ACCIDENT pREVENTION AND ALSO ENVIRONMENTAL REGULATIONS IN FORCE IN THE COUN-TRY WHERE THE pLANT IS INSTALLED AND USED.

Read carefully and entirely the following instructions before using the product. Please save these instructions in a safe place.

The unauthorised tampering/replacement of one or more parts composing the machine, the use of accessories, tools, expendable materials other than those recommended

by the manufacturer can be a danger of accident. The manufacturer will be relieved from tort and criminal liability.

•• KEEp YOUR WORK pLACE CLEAN AND TIDY. DISORDER WHERE YOU ARE WORKING CREATES A pOTENTIAL RISK OF ACCIDENTS.

• ALWAYS KEEp pROpER BALANCE AVOIDING UNUSUAL STANCE.

• BEFORE USING THE TOOL, ENSURE THERE ARE NOT DAMAGED pARTS AND THE MACHINE CAN WORK pRO-pERLY.

• ALWAYS FOLLOW THE INSTRUCTIONS ABOUT SAFETY AND THE REGULATIONS IN FORCE.

• KEEp THOSE WHO ARE NOT RESpONSIBLE FOR THE EQUIpMENT OUT OF THE WORK AREA.

• NEVER EXCEED THE MAXIMUM WORKING pRESSURE INDICATED.

• NEVER pOINT THE SpRAY GUN AT YOURSELVES OR AT

OTHER pEOpLE. THE CONTACT WITH THE CASTING CAN CAUSE SERIOUS INJURIES.

• IN CASE OF INJURIES CAUSED BY THE GUN CASTING, SEEK IMMEDIATE MEDICAL ADVICE SpECIFYING THE TYpE OF THE pRODUCT INJECTED. NEVER UNDERVALUE A WOUND CAUSED BY THE INJECTION OF A FLUID.

• ALWAYS DISCONNECT THE SUppLY AND RELEASE THE pRESSURE IN THE CIRCUIT BEFORE pERFORMING ANY CHECK OR pART REpLACEMENT OF THE EQUIp-MENT.

• NEVER MODIFY ANY pART IN THE EQUIpMENT. CHECK REGULARLY THE COMpONENTS OF THE SYSTEM.

REpLACE THE pARTS DAMAGED OR WORN.

• TIGHTEN AND CHECK ALL THE FITTINGS FOR CONNECTION BETWEEN pUMp, FLEXIBLE HOSE AND SpRAY GUN BEFORE USING THE EQUIpMENT.

• ALWAYS USE THE FLEXIBLE HOSE SUppLIED WITH STANDARD KIT.

• THE USE OF ANY ACCESSORIES OR TOOLING OTHER THAN THOSE RECOMMENDED IN THIS MANUAL, MAY CAUSE DAMAGE OR INJURE THE OpERATOR.

• THE FLUID CONTAINED IN THE FLEXIBLE HOSE CAN BE VERY DANGEROUS. HANDLE THE FLEXIBLE HOSE CARE-FULLY. DO NOT pULL THE FLEXIBLE HOSE TO MOVE THE EQUIpMENT. NEVER USE A DAMAGED OR A REpAIRED FLEXIBLE HOSE.

• NEVER SpRAY OVER FLAMMABLE pRODUCTS OR SOL-VENTS IN CLOSED pLACES.

• NEVER USE THE TOOLING IN pRESENCE OF pOTENTIALLY EXpLOSIVE GAS.

Always check that the product is compatible with the materials composing the equipment (pump, spray gun, flexible hose and accessories) with which it can come into contact. Never use

paints or solvents containing Halogen Hydrocarbons (as the Methylene Chloride). If these products come into contact with aluminium parts can provoke dangerous chemical reactions with risk of corrosion and explosion.

Avoid approaching too much to the pump pi-ston rod when the pump is working or under pressure. A sudden movement of the piston rod can cause wounds or finger squashing.

The high speed of travel of the product in the hose can create static electricity through discharges and sparks. It is suggested to earth the equipment. The pump is earthed through the earth cable of the supply. The gun is earthed through the high pressure

flexible hose. All the conductors near the work area must be earthed.

or anomalies must arrive timely within 8 days at least from the date of receipt of the plant through Registered Letter to the Shipping Agent and to LARIUS.

• The disposal of packaging materials is a customer’s competence and must be performed in accordance with the regulations in force in the country where the plant is installed and used.It is nevertheless sound practice to recycle packaging materials in an environment-friendly manner as much as possible.

LARIUS 4 - TRAnSfeR


OUT product

IN product

TAKE pROpER SAFETY MEASURES FOR THE pROTECTION OF HEARING IN CASE OF WORK NEAR THE pLANT.

IF THE pRODUCT TO BE USED IS TOXIC, AVOID INHALATION AND CONTACT BY USING pROTECTION GLOVES, GOGGLES AND pROpER FACE SHIELDS.

The conditions of guarantee do not apply in the following situations:

- improper washing and cleaning of components causing malfunction, wear or damage to the equipment or any of its parts;

- improper use of the equipment;- use that does not conform with applicable na-

tional legislation;- incorrect or faulty installation;- modifications, interventions and maintenance that

have not been authorised by the manufacturer;- use of non-original spare parts or parts that do

not correspond to the specific model;- total or partial non-compliance with the in-

structions provided.

CONDITIONS OF GUARANTEE

G

INSTALLATION

WASHING OF THE BRAND NEW EQUIPMENT

• The LARIUS 4 pump has been tested at our plant with light mineral oil left inside of the pumping elementi ad protection. Before sucking the pro-duct, carry out a washing using a diluent.

• The suction hose diameter must be proper to the viscosity of the fluid to be pumped. The installation of a filer at the end of the suction hose is recommended

SETTING-UP

SUCTION AND DELIVERY HOSES CONNECTION

• Connect the suction and delivery hoses to the pump it is suggested to tighten the fillings.

• Make sure the hoses are not too heavy for the pump structure

CONNECTION TO THE REED AIR

• For pump feed use a hose with a internal diameter no lower than 6 mm.

FILTER

AIR INPUT

LARIUS 4 - TRAnSfeR


LARIUS

LARIUS

1

SI

NO

Check all the connection fittings of the com-ponents (pump. flexble hose, etc.) before using the equipment.

• Dip the suction hose into the tank of the product.

• Let compressed air flow to the pump. Adjust air pressure to the minimum level necessary to the working of the pump continually

• The pump will start and sto when all the product chamber will be full. Each time the delivery valve is open, the pump will start again to work.

WARNING! Avoid pump iding because it could da-mage the pneumatic system and the membranes.

EMERGENCY STOP

In the case of an emergency, promptly close the air opening/closing valve (1) blocking motor power.

H WORKING

To avoid risks after stops, keep the valve open and completely discharge the pump.

POSITIONING DIAGRAM

Fix the pump on a base by using the supporting brackets holes.

NEVER INSTALL the pump upside-down or inclined

TUNING

Connect the pump with a grounding cable as indicated in the figure.

LARIUS 4 - TRAnSfeR


I PROBLEMS AND SOLUTION

SolutionCauseProblem

• The pump does not start up

• The pump has accelerated opera-tion and does not suck the product

• The pump stalled continuously

• Feed air not sufficient;

• Outlet product line clogged;

• Clogged product intake line;

• The membrane has ruptured;• The drive valve has locked;

• There is no product; • The pump sucks air;• The “balls” do not close perfectly;

• The feed air is insufficient.

• Check the air supply line. Increase the feed hose diameter;

• Clean. Detach the product outfeed hose power the pump at minimum pressure and check if the pump starts without the outfeed hose;

• Check the hose and the intake filter. Clean;

• Replace the membrane;• Press the reset buttons located at

the sides of the valve;

• Add the product;• Check the suction pipe;• Remove and clean and/or replace

the balls and ball seats;

• Check the air supply line. Increase the feed hose diameter;

• Check that the parts of the air feed circuit guarantee a sufficient flow rate (the quick-couplings cause pressure drops).

Always close the compressed air supply and release the pressure in the system before checking or replacing the pump parts.

LARIUS 4 - TRAnSfeR


J

SPARE PARTS

List of spare parts

pag. 14

LARIUS 4 - TRAnSfeR


J

27

2625

23

22

2124

23

23

22

22

2322

2322

2124

2124

2124

21

20

13

16

40 39

42

6

4

5 7 5 67

3 2 40 39

37

38

15

12

41

11

10

98

2

5 6 7 5 67

3031

32

35 34 33 36 29

27

26

18

19

1

17

15

14

41

11

10

9

8

4

EXPLODED PNEUMATIC MOTOR UNIT VIEWWARNING: always indicate code and quantity for each part required.

LARIUS 4 - TRAnSfeR


Body pump

Fluid passage cover

Screw

Fluid passage sleeve

Ball INOX 1”

Ball pTFE 1”

Ball VULKOLLAN

O ring

Ball seat

Screw

Washer

External membrane pressing disc

Membrane

O ring

O ring

Membrane push rod

Hex nut

O ring

Insert for pump body

Gasket

piston

piston rod

Washer

O ring

O ring

Spacer ring

Spacer ring

Gasket

Support bracket

Screw

Ball valve

Fitting

pressure regulator

Fitting

Elbow fitting

pressure gauge

Bayonet attack

Silencer

plug

Washer

Nipplo 1” Gas

Internal membrane pressing disc

Screw

Body pump

Fluid passage cover

Screw

Fluid passage sleeve

Ball INOX 1”

Ball pTFE 1”

Ball VULKOLLAN

O ring

Ball seat

Screw

Washer

External membrane pressing disc

Membrane

O ring

O ring

Membrane push rod

Hex nut

O ring

Insert for pump body

Gasket

piston

piston rod

Washer

O ring

O ring

Spacer ring

Spacer ring

Gasket

Support bracket

Screw

Ball valve

Fitting

pressure regulator

Fitting

Elbow fitting

pressure gauge

Bayonet attack

Silencer

plug

Washer

Nipplo 1” Gas

Internal membrane pressing disc

Screw

1

2

16

2

4

4

4

4

4

2

2

2

1

1

5

1

2

4

1

1

1

1

5

5

5

4

1

2

2

8

1

1

1

1

1

1

1

1

1

2

2

2

8

1

2

16

2

4

4

4

4

4

2

2

2

1

1

5

1

2

4

1

1

1

1

5

5

5

4

1

2

2

8

1

1

1

1

1

1

1

1

1

2

2

2

8

1

2

3

4

5*

5

5

6*

7*

8

9

10

11**

12**

13**

14

15

16

17

18

19

20

21

22

23

24

25

26

27

29

30

31

32

33

34

35

36

37

38

39

40

41

42

1

2

3

4

5*

5

5

6*

7*

8

9

10

11**

12**

13**

14

15

16

17

18

19

20

21

22

23

24

25

26

27

29

30

31

32

33

34

35

36

37

38

39

40

41

42

8350

8351

8385

8352

3326

3326/1

8305

8404

8379

8386

8387

8388

8353

91008

8403

8399

8410

8402

8409

8363

8364

8365

8362

96840

4026

8361

8360

8369

8368

54004

4004

3354

3344

3343

3341

8167

3338

8405

96205

8406

8407

8388

8371

8350

8355

8385

8356

3326

3326/1

8305

8404

8379

8357

8358

8359

8353

91008

8403

8399

8410

8402

8409

8363

8364

8365

8362

96840

4026

8361

8360

8369

8374

54004

4004

3354

3344

3343

3341

8167

3338

8405

96205

8406

8373

8388

8371

*Ball and ball housing (INOX) kit Code 40336**Diaphragm kit Code 40337***Motor gasket kit Code 40332

****Ball and ball housing (PTFE) kit Code 40336/2*****Ball and ball housing (VULKOLLAN) for abrasive products kit Code 40336/1

*** *

**

*** *

**

*** *

**

***

****

****

*****

*****

***

Pos. Pos.CodeALLUM.

CodeINOX

Description DescriptionQ.ty Q.ty

LARIUS 4 - TRAnSfeR


K

II =

2 =

G =

c =

T4 =

- 10°C ÷ + 50°C

60°C

xxxxx/AA

3

X

ATEX

MARKINGLow pressure double diaphragm transfer pumps series 2 and 4.

II 2 G c IIB T4 Tamb: -10°C ÷ + 50°C Tmax. fluid: 60°C Tech. File: LARIUS 2-4/ATEX/05

Group II ( surface)

Category 2 (zone 1)

Explosion hazardous environment with presence of gas, fog and vapour

Manufacturing safety “c”

Class of temperature T5

Environment temperature

Maximum fluid temperature

Serial number xxxxx = PROGRESSIVE/ year = AA

Relation between hazardous areas, products and categories

CATEGORIES AS PER RULES94/9/CE

Gas, vapour or fog

Gas, vapour or fog

Gas, vapour or fog

1G

2G or 1G

3G, 2G or 1G

DANGEROUS AREA

Zone 0

Zone 1

Zone 2

LARIUS 4 - TRAnSfeR


SAFETY INSTRUCTIOINS FOR ONSTALLA-TIONS IN HAZARDOUS AREAS

Before proceeding with the installation carefully read the use and service manual. All the service operations must be carried out as stated in the manual.

• The low pressure double diaphragm transfer pumps series 2 and 4 must be connected to the ground with a suitable connector anti-release and anti-rotation.

• Gas and vapour of flammable liquids must belong to the group IIB and compatible with class temperature T4.

• According with the nature of the operations and products, the operator must regularly check the presence of de-posit, the cleaning, the wearing and the correct pump’s functioning.

• It is advisable that a filter will be placed at the suction of the material to prevent solid parts entering the pump.

• The pipes used to connect suction and delivery must be metallic, or plastic with metallic braid or plastic with fabric braid with suitable earthing cable.

• According to duties it is recommended the control of diaphragms and replacement.

• The air feeling the pump needs to be filtered and origi-nated by a safe area.

The low pressure double diaphragm transfer pumps series 2 and 4 must not work empty of material.

All the operations, installation and service, must be carried out by qualified operators.

EXAMPLE OF INSTALLATION

The picture shows a typical example of installation of a Larius double diaphragm pump.

LARIUS 4 - TRAnSfeR


We Larius S.r.l. Via Stoppani, 21 24032 Calolziocorte (LC)

declare under our sole responsibility that the product:

Low pressure transfer double diaphragm pumps - series 2 and 4.

to which this declaration relates complies with the following Directives:

- Direttive 94/9/EC (ATEX)

The conformity are under observance of the following standards or standards documents:

- EN 1127-1 - EN 13463-1 - EN 13463-5

Marking

3

X II 2 G c IIB T4 Tamb.: - 10°C ÷ 50°C Tmax. fluido: 60°C Tech. File: LARIUS 2-4/ATEX /05 Technical file c/o: INERIS (0080)

Calolziocorte- LC Signature

ATEX - DECLARATION OF CONFORMITY

LARIUS 4 - TRAnSfeR


LARIUS srlVia Antonio Stoppani 21 - 23801 Calolziocorte (LC) ITALYTel: +39 0341 621152 Fax: +39 0341 621243

E-mail: [email protected]

Pierangelo CastagnaManaging Director

LARIUS 4 TRANSFERPneumatic double diaphragm pump

CE DECLARATION OF CONFORMITY

Declares under his owns resonsibility that the product:

Company

Signature

Calolziocorte, 4 June 2020 Location / Date

complies with the directives: - EC Directive 2006/42 Machinery Directive

furthermore to the harmonized standards: - UNI EN ISO 12100-1/-2

Machinery safety, basic concepts, general principles of design. Basic terminology, methodology. Technical principles.

This declaration relates exclusevely to the product in the state in which it was placed on the market, and excludes components or modifications which are added or carried out subsequently by end user.

LARIUS srlVia Antonio Stoppani 21 - 23801 Calolziocorte (LC) ITALY

TEL. +39 0341 621152 - Fax +39 0341 621243 - [email protected]

www.larius.com

Documents

ED. Larius 4 Transferlarius.org/manuali/LARIUS4_UK.pdf · LARIUS 4 - TRAnSfeR eD. 04 - 06/2020 - Cod. 150147 5 WARNINGS The table below provides the meaning of the symbols used in