Earthquake Cutouts

8/12/2019 Earthquake Cutouts

1/16

1

http://www.canon.com/c-park/

Canon Inc.

Haruko Takaku & Bookmark Inc.KID'S SCIENCEThe principle of earthquakes : Pattern

The principle of earthquakes

Plate boundary- type earthquake

Assembly tip

Writing the number of each section on its back side before cutting out the sections is highly recommended.(* This way, you can be sure which section is which even after cutting out the sections.)

Fold and crease mountain folds and valley folds before applying glue.

Take your time to cut out each piece carefully.

Trace along the folds with a ruler and an exhausted pen (no ink) to get a sharper, easier fold.

When applying glue to large areas,take care to prevent warping of paper that may be caused byover-application of glue.Apply small amounts of glue around the peripheral of the piece or use dual-sided tape tominimize warping.

Necessary utensils

scissors, set square, glue, pencil, used ballpoint pen

CautionPlease read the Assembly Instructions carefully,and assemble in order as shown on the pattern sheets.

This papercraft involves using glue, scissors,and other utensils and materials that may be dangerousto young children.Please work somewhere out of reach of young children.

Pattern

Sixteen A4 sheets (No. 1 to No. 16)

Notation Key

Mountain fold(dotted line)

Valley fold(dashed and dotted line)

Scissors line(solid line)

Arrow indicatesposition for gluingor insertion.

Guidelines(dotted lines)Align these guidelineswhen gluing pieces together.

Glue spot (Red dot)

Glue reverse side(Green dot)

* The following are used in the assembly instructions.

Indicates reverse side of paper.

An earthquake is a phenomenon in which a normally solidly attached

subterranean ground or rock bed suddenly shifts with at a certain

boundary. It also means quaking of the ground surface caused by this

shift. A plate-type earthquake is also called an ocean-type earthquake,

which occurs at a boundary between different plates. This earthquake

occurs when a plate pushed up by the other plate that starts to slide

underneath the plate springs back because it can no longer absorb the

strain, and it is repeated in a certain cycle unless a significant changeoccurs in the actions of the Earth. In the case of Japan, most of the

earthquakes are ocean-type because most of the boundaries of the plates

are under the sea. The Great Kanto Earthquake, Tokachi offshore

earthquakes and other M8 class earthquakes are of this type.


2/16

2


Canon Inc.

Haruko Takaku & Bookmark Inc.

Main body

KID'S SCIENCEThe principle of earthquakes : Pattern

Reinforcement part C


3/16

3


Canon Inc.


Main body


Reinforcement part C


4/16

4


Canon Inc.


Main body


Reinforcement part A Reinforcement part B

After you have cut thepart, glue it here.

After you have cut thepart, glue it here.


5/16

5


Canon Inc.


Main body


Continental plate


6/16

6


Canon Inc.


Continental plate

Main body



7/16

7


Canon Inc.


Main body


The

principle

of

earthquakes

KID'SSCIENCE

Oceanplate

Ocean

plate

Earthquake

center

Earthquakecenter


8/16

8


Canon Inc.


Main body Building


Donothitotherpeo

plewiththepointededges.

Doingsocouldresu

ltininjury.

Adultsshouldmake

surethatchildrenobservethiscaution.

CAUTION


9/16

9


Canon Inc.

Haruko Takaku & Bookmark Inc.KID'S SCIENCEThe principle of earthquakes : Pattern

Ocean plate (fixed part)


10/16

10


Canon Inc.


Ocean plate (fixed part)

Reinforcement part D Reinforcement part E



11/16

11


Canon Inc.


Ocean plate (movable part)



12/16

12


Canon Inc.


Ocean plate (movable part)


Ocean plate Ocean plate


13/16

13


Canon Inc.


Continental plate


Crease it and thenglue the rear sidestogether.

Reinforcement part F


14/16

14


Canon Inc.


Continental plate


Continentalplate


15/16

15


Canon Inc.


Continental plate

Ocean surface


Reinforcement part G


16/16

16


Canon Inc.


Ocean surface


Documents

Earthquake Cutouts