SECOSTEEL &CAST IRONTURNING

DURATOMIC®

TP & TK GRADES

2

EDGE INTELLIGENCE

Give every insert the long life it deserves with Duratomic® used-edge detection, which makes wear visible to the naked eye without impacting turning performance.

NEVER WASTE ANOTHER EDGE

3

Grade, Speed & Feeds ............ 18Insert Offering ........................ 19Technical Info/My Pages ........ 25

STEEL - Case Studies .................... 4CAST IRON - Case Studies ............. 5 Used Edge Detection ................ 8 TOOL SELECTION MADE EASYTool Style ................................. 10Workpiece Materials ............... 12Nose Radius & Feed Rates ...... 13Chipgrooves............................. 14Applying SMG ........................ 17

OVERCOME ANY STEEL & CAST IRON TURNING CHALLENGE WITH THE POWER OF DURATOMIC®

TP3501 / TP2501 / TP1501 / TP0501 (steel)& TK1501 / TK0501 (cast iron)

To make your shop competitive in steel turning, you must master one of the world‘s most common industrial processes. If you want to stand out from the pack, your shop needs tools that will unleash the full potential of your machines and maximize material removal rates. With Duratomic® technology, first introduced with our revolutionary TP2500 grade in 2007, Seco has built a reputation as a leader in this application area.

And after over a decade of continued research into the technology that produces our Duratomic® coatings, we have now incorporated all of that knowledge into six new grades and six new ways to help manufacturers achieve the highest level of turning productivity: TP3501, TP2501, TP1501 and TP0501 for steel turning and TK1501 and TK0501 for cast iron turning.

By keeping the same characteristics and strengths as their predecessors, these six grades represent a substantial improvement to both toughness and wear resistance. This will boost your productivity and greatly enhance the tool life you can obtain with Seco’s turning grades.

LEARN MORE AT: DURATOMIC.COM

FOR APPLICATION VIDEOS VISIT: YOUTUBE.COM/SECOTOOLSAB

STEEL

TP3501: SECURED PRODUCTIVITY • First choice for secure productivity in steels• Intended for tough, demanding applications • Ideal for intermittent machining and/or speed limitations• Roughing to finishing • Highly capable in stainless steel applications

TACKLE ANY STEEL TURNING APPLICATION

To offer you a comprehensive

range of grades for steel turning

– and make it easy to improve

performance and productivity

for your turning applications

– we have the well-known and

highly effective TP3501, TP2501,

TP1501 and TP0501 Duratomic®

grades. Since its introduction

in 2007, we have maintained

all the characteristics of each

Duratomic® TP grade while

applying the vast knowledge we

have learned from the technology

itself and how it affects properties

such as toughness and wear

resistance to further improve the

technology – and make an impact

on your bottom line.

CASE STUDY

Part ROLLER

Workpiece material A105Low-alloy general structural steels

SMG SMG P4

Operation Roughing

Cutting method O.D. and Facing

Coolant No

Grade TP3501 Competitor

InsertCNMG432-M3 TP3501 CNMG432

4 useable edges 4 useable edges

Vc 520 sfm (158 m/min) 410 sfm (125 m/min)

f 0.0120 in/rev (0.30 mm/rev) 0.0100 in/rev (0.25 mm/rev)

APMX 0.1000 in. (2.54 mm) 0.1000 in. (2.54 mm)

Tool Life 6 pcs 5 pcs

Tool Life 47 mins 32 secs 1 hr 16 secs

Failure Mode Flank Wear Flank Wear

Output/Hour 7.27 pcs 4.82 pcs

Total In CutTime 7 mins 55 secs 12 mins 3 secs

Total Cost Per Component (USD) $15.49 $23.23

Total Cost (USD) $131,675.22 $197,464.09

Total Cost Savings (USD) $65,788.87 (33%)

Achieve higher cutting speeds with inserts featuring our premium Duratomic® coating for substantial cost savings in all steel and cast iron turning applications.

4

5

TP2501: VERSATILE PRODUCTIVITY • First choice grade in most steels• When reliability is required • Versatility and more intermittent machining• Roughing to finishing• Capable in cast irons and stainless steel

TP0501: HIGH-SPEED PRODUCTIVITY• First choice in high-carbon steels• When highest productivity is required • Continuous cuts and limited intermittent machining• Roughing and higher speeds than TP1501• Effective for dry machining and gray cast iron

TP1501: BALANCED PRODUCTIVITY • First choice in low-alloy steels• When optimizing is required• Versatile productivity and some intermittent machining• Finishing and lower heat applications than TP0501 • Capable of intermittent machining of ductile cast iron

Grade TP2501 Competitor

Insert WNMG332-M3 TP2501 WNMG332

Vc 492 sfm (150 mm/min) 394 sfm (120 mm/min)

f 0.010 in/rev (0.25 mm/rev) 0.010 in/rev (0.25 mm/rev)

APMX 0.060 in (1.5 mm) 0.060 in (1.5 mm)

Tool life 1,200 - 1,500 parts 200 - 500 parts

CASE STUDY

Part DRIVER GEAR

Workpiece material SCM415

SMG SMG P3

Cutting mode Internal interrupted cut

Coolant Emulsion

Grade TP0501 Competitor

Insert TNMG433-M5 TP0501 TNMG433

Vc 984 sfm (300 mm/min) 984 sfm (300 mm/min)

f 0.014-0.016 in. (0.35-0.40 mm) 0.014-0.016 in. (0.35-0.40 mm)

APMX 0.079-0.160 in. (2-4 mm) 0.079-0.160 in. (2-4 mm)

Tool life > 50 parts < 30 parts

CASE STUDY

Part BEARING

Workpiece material 100Cr6

SMG SMG P7

Cutting mode Continuous

Coolant Emulsion

Customer expectations exceeded with improved process stability in small demanding components with interruptions for a 25% increase in productivity.

Grade TP1501 Competitor

Insert TNMG332-M3 TP1501 TNMG332

Vc 853 sfm (260 mm/min) 787 sfm (240 mm/min)

f 0.008 in/rev (0.2 mm/rev) 0.006 in/rev (0.15 mm/rev)

APMX 0.060 in. (1.5 mm) 0.060 in. (1.5 mm)

Tool life 20 parts 5 parts

CASE STUDY

Part PISTON

Workpiece material C60

SMG SMG P3

Cutting mode Continuous

Coolant Emulsion

In many ordinary steel applications TP1501 provides major tool life or productivity gains without sacrificing reliability.

TP0501 enables more than 60% greater tool life per number of parts in roller bearing steel materials.

INTERNAL SEMI-FINISHING

TOOL LIFE / NO. OF PARTS

1,200

1,000

800

600

400

200

0

1,400

TP25

01 -

M3

Com

petit

or

TOOL LIFE / NO. OF PARTS

50

40

30

20

10

0 TP05

01 -

M5

Com

petit

or

CAST IRON

TK1501: BALANCED CAST IRON PRODUCTIVITY • First choice in ductile cast iron• When optimizing is required• Versatile productivity and intermittent machining in most cast irons• High reliability at moderate speeds for demanding applications• MR9 geometry offers the most secure productivity solution available • Also suitable for general steel applications

CONQUER ALL CAST IRON CHALLENGES

Since the launch of our first Duratomic® grades for cast iron in 2013, TK2001 and TK1001, we have further improved how we apply Duratomic® technology to turning inserts for cast iron applications. By expanding the application range and focusing on what makes each grade particularly useful, we have improved performance and reliable productivity in both grey and nodular ductile cast iron.

Grade TK1501 Competitor

Insert CNMG432-M4 TK1501 CNMG432

Tool life 45 parts 45 parts

CASE STUDY

Part SHAFT

Workpiece material Ductile

SMG SMG K4

Coolant Emulsion

Vc 722 sfm (220 mm/min)

f 0.010 in/rev (0.25 mm/rev)

APMX 0.079 in. (2 mm)

Higher wear resistance in lower speed applications compared to competitor.

A moderate cutting speed results in reliable performance improvements, as the competitor’s insert is prone to chipping (shown below) even with these parameters.

RELIABLE SHAFT MACHINING

6

TK1501 Competitor

NO. OF PARTS PER EDGE

7

Grade TK0501 Competitor

Insert CNMA433-MR9 TK0501 CNMA433

Vc 492 sfm (150 mm/min) 492 sfm (150 mm/min)

f 0.012 in/rev (0.30 mm/rev) 0.012 in/rev (0.30 mm/rev)

APMX 0.079-0.157 in. (2-4 mm) 0.079-0.157 in. (2-4 mm)

Tool life 6 parts per edge 4 parts per edge

CASE STUDY

Part CYLINDER BLOCK,

PARTLY INTERRUPTED

Operation Rough-Boring

Workpiece material EN-GJS-600, Ductile iron

SMG SMG K4

Coolant Flood

NO. OF PARTS PER EDGE

Outperform the competition and produce 50% more parts with a superior solution.

6

5

4

3

2

1

0

TK05

01 -

MR9

Com

petit

or

TK0501: SECURED PRODUCTIVITY• First choice in grey cast iron• When the highest productivity is required• Highest wear resistance for continuous cuts in all cast irons• Higher speed capabilities in cast iron applications than TK1501• Using MR9 creates a very secure, high productivity solution• High performance even in hardened steels

Reducing manufacturing costs requires reducing waste – and every unused cutting edge in the trash impacts your bottom line. But you don‘t need microscopes or magnifying glasses to see wear with used-edge detection, a simple solution that will save money with every fully used tool.

USED EDGE DETECTION New edge 10 seconds in cut 15 minutes in cut

All Black New edge 10 seconds in cut 15 minutes in cut

Black/TiN-flankBlack/TiC-flank

New edge 10 seconds in cut 15 minutes in cut

Classic TiN or TiN-top New edge 10 seconds in cut 15 minutes in cut

USED-EDGEDETECTION

Duratomic® used-edge detection technology provides the highest possible wear visibility at the same time it excels in real-life working conditions.

Conclusion: With careful observation, wear scarring can be seen on gold TiN coated inserts. However, the presence of this coating on top of aluminum oxide usually results in a significant reduction in performance. The situation is even worse for black inserts, which makes it very difficult to tell which cutting edges are used and which ones are not. Avoid all this waste with Duratomic® coatings made with a chrome color that boosts the visibility of used edges – and helps you reduce part costs per edge.

8

Insert

Fracture

Notch

Wear

Plastic

Deformation

Edge

Chipping

Thermal

Mechanical

Fracturing

Built-up

Edge

Flank

Wear

Crater

Wear

9

CORRECTIVE ACTIONS (TO RAPID FLANK WEAR)

• Select a harder, more wear resistant grade.

• Apply coolant correctly• Reduce the cutting speed

(RPM or SFPM)

CORRECTIVE ACTIONS (TO RAPID CRATER WEAR)

• Use a coated grade, coatings containing relatively thick layers of aluminum oxide are best

• Apply coolant• Use a freer cutting geometry

to reduce heat• Reduce the cutting speed

(RPM or SFPM)• Reduce feed rate• Increasing the lead angle will

have a small, but positive, effect

CORRECTIVE ACTIONS

• Increase the cutting speed (RPM or SFPM)

• Any coating, but especially a nitride coating, will reduce built-up edge

• Select an insert with a sharper, freer cutting edge geometry

• Apply coolant correctly. Increasing the concentration usually helps

• Use an insert with a smoother (polished) surface

CORRECTIVE ACTIONS

• Ensure proper (rigid) machine tool setup

• Minimize deflection • Select a stronger cutting edge

geometry • Select a tougher insert grade• Reduce the feed rate

(especially at the entrance or exit of the cut)

• See also corrective actions for built-up edge as built-up edge is a frequent cause of chipping

CORRECTIVE ACTIONS

• Apply coolant correctly or remove completely

• Select a tougher insert grade (higher cobalt content)

• Reduce the cutting speed (RPM or SFPM)

• Reduce the feed rate

CORRECTIVE ACTIONS

• Apply coolant correctly • Use a harder, more wear

resistant grade with a lower cobalt content

• Using a freer cutting insert geometry will have a small but positive effect

• Reduce the cutting speed (RPM or SFPM)

• Reduce the feed rate• Select an insert with a larger

nose radius

CORRECTIVE ACTIONS

• Correct for all other failure mechanisms besides normal flank wear

• Verify set-up rigidity• Select a tougher insert grade

(higher content of cobalt)• Select a thicker insert• Select an insert with a tougher

cutting edge• Select an insert with a

chipbreaker geometry designed for higher feed rates

• Reduce the depth of cut • Reduce the feed rate• Check the workpiece for hard

inclusions or difficult entry

CORRECTIVE ACTIONS

• Vary the depth of cut when using multiple passes

• Use taper machining techniques when possible

• Use a tool with a larger lead angle

• Increase cutting speed if machining a high temp alloy – NOTE: This will generate more flank wear

• Use a chipbreaker designed for high feed rates

• Select a tougher insert grade • Reduce the feed rate

TROUBLE-SHOOTINGCOMMON WEAR MODES

10

TOOL SELECTION MADE EASY: THE RECOMMENDED PROCESS FOR SELECTING THE RIGHT TOOLAs an illustration of the tool selection process, consider a part that is made of 4140 steel. There is a feature showing an undercut at 25° and the finish requirement is 128 R

a. APPLICATION EXAMPLE:

Insert DN... 93°

DDHNR DDHNL

93°

DDJNR DDJNL

93°

MDJNR MDJNL

62.5°

DDPNN

STEP 1: TOOL STYLEMatch the shape of the part to be machined with the sketches shown below. Select toolholder and insert style to suit the machining operation to be carried out.

EXTERNAL TURNING, -D STYLE, ANSI -M STYLE AND -P STYLE (M STYLE WITHOUT TOP CLAMP)

Insert CN... 75°

DCKNR DCKNL

75°

MCKNR MCKNL

95°

DCLNR DCLNL

95°

MCLNR MCLNL

40°

MCMNN

75°

MCRNR MCRNL

Insert R...

DRGNR DRGNL MRGNR MRGNL MRGOR MRGOL

11

Insert DC... 93°

SDJCR SDJCL

62.5°

SDPCN

Insert RC...

SRDCN SRGCR SRGCL

Insert SC... 45°

SSDCN

Insert TC... 90°

STGCR STGCL

Insert VB... 95°

SVLBR SVLBL

72.5°

SVVBN

EXTERNAL TURNING, ANSI -S C-LOCK (S TOOLHOLDER)

Insert CC... 90°

SCGCR SCGCL

95°

SCLCR SCLCL

50°

SCMCN

75°

SCRCR SCRCL

Insert WN... 95°

DWLNR DWLNL

95°

MWLNR MWLNL

Insert VN... 93°

DVJNR DVJNL

93°

MVJNR MVJNL

95°

MVLNR MVLNL

117.5°

DVTNR DVTNL

117.5°

MVTNR MVTNL

Insert TN... 90°

MTCNN

60°

MTENNS

90°

DTFNR DTFNL

90°

MTFNR MTFNL

90°

DTGNR DTGNL

Insert SN... 45°

MSDNN

75°

DSKNR DSKNL

75°

MSKNR MSKNL

75°

MSRNR MSRNL

45°

MSSNR MSSNL L

Insert TN... 90°

MTGNR MTGNL

93°

DTJNR DTJNL

93°

MTJNRS MTJNLS

95°

MTLNR MTLNL

12

STEP 2: WORKPIECE MATERIAL (STEEL & CAST IRON)Find the name of the materials being machined and identify the Seco Material Group that is appropriate for your material of interest.

STEELS, FERRITIC AND MARTENSITIC STAINLESS STEELS

SMG DESCRIPTION

PROPERTIES

UTS = Ultimate tensile strength (ksi) REFERENCE MATERIAL (ANSI)

P1 Free-cutting steels 50 < UTS < 751213UTS = 55 ksi

P2Low-alloy ferritic steels, C < 0.25%wt Low-alloy weldable general structural steels

45 < UTS < 85A 573 Gr. 58UTS = 60 ksi

P3

Ferritic & ferritic/pearlitic steels, C < 0.25%wt Weldable general structural steels Case hardening steels

60 < UTS < 905115UTS = 80 ksi

P4 Low-alloy general structural steels, 0.25% < C < 0.67%wt Low-alloy Quench & Temper steels

75 < UTS < 1751045UTS = 95 ksi

P5Structural steels, 0.25% < C < 0.67%wt Quench & Temper steels

80 < UTS < 1754140UTS = 100 ksi

P6Low-alloy through-hardening steels, C > 0.67%wt Low-alloy spring and bearing steels

75 < UTS < 1701095UTS = 85 ksi

P7Through hardening steels, C > 0.67%wt Spring and bearing steels

85 < UTS < 17052100UTS = 95 ksi

P8Tool steels High Speed Steels (HSS)

85 < UTS < 170H13UTS = 100 ksi

P11 Ferritic & martensitic stainless steels 60 < UTS < 170420UTS = 95 ksi

CAST IRONS

SMG DESCRIPTION PROPERTIES REFERENCE MATERIAL (ANSI)

K1 Grey cast irons (GCI) 20 < UTS < 40 A48 35 B

K2 Compacted graphite irons (CGI) 50 < UTS < 73 Grade 400-15

K3 Malleable cast irons (MCI) 60 < UTS < 70 A220 60004

K4 Nodular cast irons (SGI) 80 < UTS < 120 80-55-06

K5 Austempered ductile irons (ADI) 130 < UTS < 230 1050/700/7

K6 Austenitic lamellar cast irons 24 < UTS < 29 A436 Type 1 (Ni-Resist 1)

K7 Austenitic nodular cast irons 54 < UTS < 60A439 Type D-2M (Ni-Resist D-2M)

13

Find the feed recommendations for a chosen chipbreaker. Then look in the surface finish table below to be sure that the required surface finish can be achieved. The maximum feed rate should always be considerably smaller than the nose radius. A feed rate that is too low can result in poor chipbreaking and tool life.

STEP 3: NOSE RADIUS & FEED RATE

Surface

finish

Ra value

(μ inch)

Nose radius, r (inch)

Feed rate, f (inch/rev)

.008 .016 .032 .047 .062 .094

2464128250320

.002

.003

.005––

.003

.005

.006

.009–

.004

.006

.009

.013

.016

.005

.008

.011

.016

.019

.006

.009

.013

.018

.022

.007

.011

.016

.022

.027

NOSE RADIUSThe choice of nose radius is dependent on the workpiece design and the machining operation. The nose radius influences cutting data choice and the surface finish achieved. The maximum feed rate that can be used depends on a number of factors including machine power, stability, workpiece material, insert shape and size, nose radius, chipbreaker, grade and setting angle.

Small nose radius = universal machining, low cutting forces (less vibration risk).Large nose radius = strong, suitable for high cutting data, good surface finish.

Feed (ipr)

Ra(μ in)

Standard M3

Standard insert geometry

Rmax

HIGH FEED INSERTS The Seco High Feed inserts offer

• Excellent surface finish at high feed rates• Superior surface finish at normal feed rates

The use of High Feed inserts often eliminates the need for finish grinding. High Feed inserts are designed for small cutting depths.

CNMG 432W-M3, TP2501, = 95°, APMX = .040”, cutting speed adjusted for feed, workpiece material: steel, Seco material group 4.

WIPER INSERT OPERATION GUIDELINESFavorable surface finish results are lost, if the cutting edge angle diverges from:95° (C & W style inserts)93° (D & T style inserts)

Maximum diversion angle allowed ± 2°, Back turning is not recommended

For more info, see page 50 of the Turning Navigator Catalog.

Wiper insert geometry

Rmax

DU

RAT

OM

IC

EDP 15761

02960087

®

WNMG060408-M3, TP0501

WNMG 332-M3

1111111 001/015

DU

RAT

OM

IC® WNMG080412-M6, TP1501

WNMG 433-M6

02959875

EDP 15158

NOSE RADIUS

*Wiper W-M3

14

CHIPBREAKER OVERVIEWThe chipbreakers are designed to control the chips when turning long chipping materials. The numerical designations describe the application area as follows:

Numerals 1 - 9:1 = For low feed rates and easy conditions9 = For high feed rates and

rough conditions

-FF1 Chipbreaker for negative inserts. Used to achieve a very fine finish when turning steel and stainless steel.Machining range: f = .003–.012 ipr, APMX = .008–.120”

-FF2 Chipbreaker for high feed finishing and medium-roughing machining of steel and cast iron.Ensures safe and well directed chip flow and good surface finish.Machining range: f = .003–.012 ipr, APMX = .008–.060”

-MF1 Chipbreaker intended for machining stainless steel, superalloys and titanium alloys. Type ..GG insert has a sharp, precision ground edge. Type ..MG insert has a lightly honed cutting edge for increased strength. MF1 is intended for use in semi-finishing and finishing applications.Machining range: f = .003–.012 ipr, APMX = .008–.140”

-MF2 First choice for finishing with negative inserts. Suitable for chip control at depths of cut down to .010”, provided that the feed rate is in excess of .010”/rev. Good capacity for medium-rough machining.Machining range: f = .004–.016 ipr, APMX = .008–.120”

NEGATIVE INSERT CHIPBREAKERS

TYPE

OF

OPE

RAT

ION

EDGE STRENGTH/FEED RATE

STEP 4: CHIPGROOVESSelect the proper chip groove by understanding both feed rate and depth of cut, in which you will be machining for your component.

FINISHING at low depth of cut. Typical APMX = .008–.032” and f = .008 in/rev.

MEDIUM-ROUGH MACHININGTypical one pass machining at APMX = .032–.120” and f = .012 in/rev.

ROUGH MACHINING at higher depth of cut and feed rate in most cases with difficult surface conditions such as scale, irregularities and other conditionsleading to interruptions and edge damage. Typically APMX = .12–.28” and f = .02 in/rev.

Steel

(ISO-P)

Stainless Steel

(ISO-M)

Cast Iron

(ISO-K)

Hardened Steels

(ISO-H)

FF2

MF1

M3

MF1

M3

MF4

M5

M3

M6

M5

MR9

–

F1

F1

F1

F1

MF2

MF2

M3

_

M5

M5

M5

–

NEGATIVE INSERT CHIPGROOVE RECOMMENDATIONS

POSITIVE INSERT CHIPGROOVE RECOMMENDATIONS

15

NEGATIVE INSERT CHIPBREAKERS

-MF3 Chipbreaker with positive cutting rake angle intended for moderately difficult stainless steel. The MF3 is also intended for light roughing in relatively soft, “tacky” steel and difficult to machine stainless steel if the depth of cut is limited. MF3 can also be used for finishing of cast iron.Machining range: f = .006–.016 ipr, APMX = .040–.200”

-MF4 Chipbreaker intended for medium/finishing of stainless steel, very open and highly positive geometry.Machining range: f = .006–.020 ipr, APMX = .020–.160”

-MF5 Chipbreaker intended for medium finishing of steel and stainless steel at high feeds. Very easy cutting and open geometry.Machining range: f = .008–.031 ipr, APMX = .008–.100”

-M3 First choice for medium-rough machining and also the most versatile Seco chipbreaker. In most cases, it is the only chipbreaker needed. Offers the best useful life and best chipbreaking in a wide range of cutting data and workpiece materials. Suitable for pre-cision forged and cast workpieces (Near Net Shape workpieces or NNS) as regards both chip control and edge strength. Machining range: f = .006–.020 ipr, APMX = .020–.200”

-M4 Chipbreaker intended for cast iron. Positive rake angle with a narrow T-land gives low cutting forces. First choice for cast iron machining at high speeds. Machining range: f = .004–.028 ipr, APMX = .008–.276”

-M5 First choice for roughing by means of double-sided inserts. Intended for demanding operations at high feed rates in steel, stain-less steel and cast iron. Combines high edge strength with comparatively low cutting forces.Machining range: f = .010–.028 ipr, APMX = .060–.275”

-M6 Strong double-sided chipbreaker, intended for semi-roughing and roughing of steel. A well-balanced design combining excellent chip control and relatively low cutting forces which provides reliable cutting action in both continuous as well as interrupted cuts. Well suited also for machining of ferritic and martensitic stainless steels. Machining range: f = 0.008-0.031 in/rev, APMX = 0.040-0.275 inch

-MR4 The MR4 has a negative T-land, which gives extremely high edge strength. The chipbreaker is intended for more difficult machining applications on superalloys and titanium alloys, such as intermittent cuts and the machining of parts with raw surface. Machining range: f = .006–.022 ipr, APMX = .060–.275”

-MR7 The strongest chipbreaker for double-sided inserts. The MR7 is suitable for high feed rates and depths of cut that normally require a single-sided insert. The chipbreaker has a wide negative T-land, which gives high edge strength.Machining range: f = .010–.032 ipr, APMX = .060–.275”

-MR9 Chipbreaker for double sided inserts in our cast iron grade range. Large support surfaces improve strength and heat transport from the cutting zone through the insert is more efficient. Primarily designed for high feed rates and depth of cut, interruptions and forging skins. Machining range: f = .010–.032 ipr, APMX = .060–.275”

-R4 Chipbreaker for single-sided inserts. It has a positive cutting edge which gives low cutting forces.Machining range: f = .008–.024, APMX = .080–.400”

-R5 Chipbreaker for single-sided inserts. Recommended for medium-roughing of steel.Machining range: f = .012–.040 ipr, APMX = .080–.480”

-R6 Chipbreaker for single-sided inserts. Recommended for medium-roughing of stainless steel.Machining range: f = .010–.025 ipr, APMX = .080–.400”

-RR6 A very easy-cutting chipbreaker for single-sided inserts. Recommended for roughing of stainless steel and steel.Machining range: f = .012–.040, APMX = .080–.480”

-R7 A strong but easy-cutting chipbreaker for single sided inserts. The R7 is well suited for intermittent machining of both stainless and ordinary carbon steel.Machining range: f = .016–.040, APMX = .070–.500”

16

POSITIVE INSERT CHIPBREAKERS

W-F1 A versatile chipbreaker for positive inserts. For finishing machining of steel, stainless steel and cast iron giving good surface finish. Suitable for high feed rates at small depth of cut.Machining range: f = .002–.020, APMX = .010–.120”

W-MF2 First choice for finishing with negative inserts. Chipbreaker suitable for finishing machining of steel, stainless steel and cast iron at high feed rates giving good surface finish.Machining range: f = .002–.024 ipr, APMX = .010–.160”

W-MF5 Chipbreaker intended for medium finishing of steel at high feed. The geometry is very open and highly positive.Machining range: f = .008–.031 ipr, APMX = .008–.105”

W-M3 Versatile chipbreaker for high feed finishing and medium-roughing machining of steel, stainless steel and cast iron. Operates in a wide application area. Gives a good surface finish even at high feeds.Machining range: f = .008–.035 ipr, APMX = .020–.240”

W-R7 A strong easy cutting chipbreaker for single sided inserts. Intended for the highest feeds when medium-roughing and rough machining of steel, stainless steel and cast iron. Gives a good surface finish even at the higher feeds.Machining range: f = .016–.048 ipr, APMX = .080–.375”

CHIPBREAKER PROGRAM, HIGH FEED INSERTS (WITH WIPER RADIUS)

-FF1 Chipbreaker for positive inserts. Used to achieve a very fine finish when turning steel and stainless steel.Machining range: f = .002–.012 ipr, APMX = .008–.080”

-F1 A versatile chipbreaker for positive inserts. Positive geometry with sharp cutting edge gives easy-cutting properties. Suitable for high feed rates at fine depths of cut on precision forgings and castings.Machining range: f = .004–.012, APMX = .020–.100”Machining in bar automatics, for instance: f = .003–.010 ipr, APMX = .040–.120”

-F2/M3 Chipbreaker for positive inserts. Ensures safe chip flow on finishing and medium roughing in steel and stainless steel.Machining range: f = .006–.016 ipr, APMX = .030–.200”

-M5 Rigid chipbreaker for positive inserts. Intended for medium-rough and rough machining of steels, stainless steels and cast iron. Combines high edge strength with comparatively low cutting forces.Safe action in interruptions and rough skin on parts.Machining range: f = .006–.024 ipr, APMX = .039–.200”

-R8 A very strong chipbreaker for single-sided inserts. The R8 is intended for high feed rates when machining castings and forgings of austenitic stainless steel.Machining range: f = .014–.031 ipr, APMX = .070–.500”

-RR9 Extremely strong chipbreaker for single-sided negative inserts, for use at high feed rates.Suitable for difficult castings and forgings and for austenitic stainless steel.Machining range: f = .020–.048 ipr, APMX = .100–.600”

-UX Chipbreaker for negative inserts. Positive cutting rake with sharp edge. Low cutting force.Suitable for slim components.Machining range: f = .008–.016 ipr, APMX = .040–.240”

SUPPLEMENTARY CHIPBREAKER PROGRAM

17

Chipbreaker for positive inserts. Used to achieve a very fine finish when turning steel and stainless steel.

Suitable for high feed rates at fine depths of cut on precision forgings and castings.

Chipbreaker for positive inserts. Ensures safe chip flow on finishing and medium roughing in steel and stainless steel.

Suitable for difficult castings and forgings and for austenitic stainless steel.

STEEL

SMG Description

TP0501 TP1501 TP2501 TP3501

f (in/rev) f (in/rev) f (in/rev) f (in/rev)

0.008 0.016 0.008 0.016 0.008 0.016 0.008 0.016

P1 Free-cutting steels 2560 2002 2264 1674 1936 1476 1674 1100

P2 Low-alloy ferritic steels, C < 0.25%wt 2494 1936 2230 1624 1838 1510 1624 1082

P3 Case-hardening steels, C < 0.25%wt 2034 1674 1640 1312 1870 1526 1182 820

P4 Low-alloy Quench & Temper steels, 0.25% < C < 0.67%wt 1902 1476 1674 1230 1428 1082 1246 820

P5 Quench & Temper steels, 0.25% < C < 0.67%wt 1706 1428 1378 1100 1328 1082 984 722

P6 Low-alloy bearing steels, C > 0.67%wt 2034 1574 1804 1328 1526 1164 1346 886

P7 Bearing steels, C > 0.67%wt 1804 1510 1460 1164 1280 1148 936 688

P8 Tool steels 1706 1428 1378 1100 1328 1082 886 590

P11 Ferritic & martensitic stainless steels 1772 1460 1428 1132 1378 1116 820 426

P12 Maraging and precipitation-hardening stainless steels 1034 870 836 672 574 524 492 246

STEP 5: CUTTING DATA

This cutting data for CNMG432 can be used as an example for referencing the SMG steel classification. It comes from the same single source cutting data service that is used for box label data, data in My Pages and catalogs for consistency.

SMG Description

TK0501 TK1501 TP1501

f (in/rev) f (in/rev) f (in/rev)

0.008 0.016 0.008 0.016 0.008 0.016

K1 Grey Cast Iron (GCI) 1870 1492 1574 1164 1476 1328

K2 Compacted graphite irons (CGI) 1378 1164 1378 1132 1280 1148

K3 Malleable cast irons (MCI) 1164 984 1164 952 1082 968

K4 Nodular cast irons (SGI) 1116 936 1116 918 1034 918

K5 Austempered ductile irons (ADI) 672 558 656 542 606 558

K6 Austenitic lamellar cast irons 1148 918 968 722 902 820

K7 Austenitic nodular cast irons 854 706 854 688 788 706

CAST IRON

SMG Description

TK0501 TK1501 TP1501

f (in/rev) f (in/rev) f (in/rev)

0.008 0.016 0.008 0.016 0.008 0.016

K1 Grey Cast Iron (GCI) 1968 1706 1738 1444 1492 1510

K2 Compacted graphite irons (CGI) 1526 1362 1492 1312 1296 1312

K3 Malleable cast irons (MCI) 1296 1148 1264 1116 1100 1116

K4 Nodular cast irons (SGI) 1230 1100 1198 1066 1050 1066

K5 Austempered ductile irons (ADI) 738 656 722 624 624 640

K6 Austenitic lamellar cast irons 1230 1050 1066 886 918 936

K7 Austenitic nodular cast irons 936 836 918 804 804 804

This cutting data for CCMT32.52-M5 can be used as an example for referencing the SMG cast iron classification for 15 minutes tool life and 0.04 in D.O.C. including a reference to TP1501 from the TP grade chain.

This cutting data for CNMG433-MR7 can be used as an example for referencing the SMG cast iron classification. for 15 minutes tool life and 0.12 in D.O.C including a reference to TP1501 from the TP grade chain.

18

STEP 6: GRADE, SPEED & FEED - GENERAL MACHINING RECOMMENDATIONS

TK0501

TK1501

SMG SMG

MR9

MR9

K4K1

P

H

Stable Unstable

WEAR RESISTANCE, HEAT

RESISTANCE (VC, f x APMX)APPLICATION AREA IN CAST IRON

WEAR RESISTANCE TOUGHNESS

The cast iron grade chain provides a versatile product range that has an even wider coverage of the cast iron application area. TK1501 is the first choice in ductile cast iron and TK0501 is the first choice in grey cast iron material, but the interchange capability of the grades i.e. TK0501 works amazingly well in continuous application in ductile casts as well as TK1501 could be a better choice at more limited speed in more toughness demanding grey cast. iron applications. Worth noting is the complementary capability of TP1501 from the TP grade chain in cast irons especially at higher speed in ductile irons with some level of interrupted cuts. Always remember the ability of MR9 to drastically shift both the grades to higher toughness keeping the highest wear resistance.

TP0501

TP1501

TP2501

TP3501M

M

K

K

K

K

K

M

M

WEAR RESISTANCE, HEAT

RESISTANCE (VC, f x APMX)

Stable UnstableSemi-stable

TOUGHNESS

CONDITIONS

WEAR RESISTANCE

Best suited

Suitable

Best suited Best suited

Suitable Suitable

APPLICATION AREA IN STEEL

CONDITIONS Semi-stable

The grade chain provides a very versatile and comprehensive range to cover the whole steel turning area. TP2501 is the “king” of versatility and TP3501 the secure choice. TP1501 provides a balance of performance and productivity for applications in low-alloy steels or using lower speeds. TP0501 offers a high-heat profile in general steel machining, particularly in high alloy steels.

The following chart illustrates the indicative positioning and application area for the following grades in steel and cast iron applications.

19

CODE KEY

INSERT SIZE

For equal sided inserts I.C. in 1/8ths of an inch.Examples:1/8” = 1 5/32” = 1.2 3/16” = 1.5 7/32” = 1.8 1/4” = 2 5/16” = 2.5 3/8” = 3 1/2” = 4 5/8” = 5 3/4” = 6 7/8” = 7 1” = 8 1/4” = 10

Rectangle and parallelogram inserts require two digits: 1st Digit-Number of 1/8ths in width. 2nd Digit-Number of 1/4ths in length.

INSERT NOSE RADIUS

0.0 = Sharp to .002”0 = Sharp to .004”0.5 = .008”1 = .016”2 = .031”3 = .047”4 = .062”6 = .094”8 = .125”

INSERT THICKNESS

Number of 1/32nds on inserts less than 1/4”

I.C.Number of 1/16ths on inserts 1/4” I.C. and over.

Insert shape

Side clearance angle

Tolerances

Insert type

I.C.

Thickness

Nose radius

Chipbreaker designationLetter: F = FinishingM = MediumR = Roughing

GradeCutting edgecondition

First digit:1 = Low edge strength9 = High edge strength

-C C M T 4 3 2 TP2501F1W

DURATOMIC®

INSERT PROGRAM

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

CCGX21.50.5W-F1 - 15856 - - - -CCGX32.50.5W-F1 - 15857 - - - -CCMT21.50.5-F1 49290 15859 15858 - - 46639CCMT21.50.5-FF1 - 19361 - - - -CCMT21.50.5-M3 49292 19397 19356 - - -CCMT21.50.5-MF2 49293 14244 - - - -CCMT21.51-F1 49294 19555 19554 - 46638 46637CCMT21.51-FF1 03169506 19404 - - - -CCMT21.51-M3 49295 19559 19523 - 46640 46639CCMT21.51-MF2 49296 14245 14937 14934 - -CCMT21.51W-F1 - 19338 - - - -CCMT21.51W-MF2 - 14246 - - - -CCMT21.52-F1 49298 19588 - - - -CCMT21.52-M3 49299 19463 - - 46641 -CCMT21.52-MF2 49300 14247 14939 14938 - -CCMT32.50.5-F1 49302 19474 19369 - - -CCMT32.50.5-M3 - 19371 19359 - - -CCMT32.50.5-MF2 49303 14248 - - - -CCMT32.51-F1 49305 19594 19405 - 46646 46483CCMT32.51-FF1 03133179 19486 - - - -CCMT32.51-M3 49308 20359 19541 - 46655 46503CCMT32.51-M5 61339 14271 14941 14940 46540CCMT32.51-MF2 49309 14249 14943 - - -CCMT32.51W-F1 03169500 19161 19225 - - -CCMT32.51W-MF2 49311 14250 14944 - - -CCMT32.52-F1 49312 19599 19550 - 46648 46484CCMT32.52-M3 49313 19616 19613 - 46656 46505CCMT32.52-M5 49314 14272 14947 14945 46649 46485CCMT32.52-MF2 49315 14251 14952 14951 - -CCMT32.52W-F1 - 19306 19223 - - -CCMT32.52W-M3 - - 19353 - - -CCMT32.52W-MF2 - 14252 14953 - - -CCMT32.53-M3 61345 19372 19366 - - -CCMT321-M3 - 19358 - - - -CCMT431-F1 49316 19482 - - - -CCMT431-M3 49317 19516 19392 - 46552 -CCMT431W-F1 - 18965 - - - -CCMT432-F1 49318 19551 - - 46541 -CCMT432-M3 49319 19617 19552 - 46657 46506CCMT432-M5 49320 14274 14955 14954 46650 46489CCMT432-MF2 49322 14253 14957 - - -CCMT432W-F1 - 18975 - - - -CCMT433-F1 - 19367 - - - -CCMT433-M3 49323 19408 19398 - 46658 46507CCMT433-M5 61346 14275 14962 14960 46542 -CCMT53.52-M3 - 19632 - - 46553 -CCMT53.52-M5 03169825 03169650 - - - -CCMT53.53-M3 - - - - 46555 -CCMT53.53-M5 61594 14276 - - - -CCMT53.54-M5 49324 14277 - - - -CNMA431 - - - - - 46691CNMA432 - - - - 46809 46692CNMA432-MR9 - - - - 46322 46320CNMA433 - - - - 46810 46693CNMA433-MR9 - - - - 46327 46323CNMA434 - - - - 46623 -CNMA434-MR9 - - - - 46330 46328CNMA542 - - - - 46624 46490CNMA543 - - - - 46625 46491CNMA543-MR9 - - - - 46296 46295CNMA544 - - - - 46626 46492CNMA544-MR9 - - - - 46299 46297CNMA643 - - - - 46811 46694CNMA644 - - - - 46812 46695CNMG321-M3 - 17489 - - - -CNMG322-M3 - 17577 - - - -CNMG430.5-FF2 - 15587 - - - -CNMG431-FF1 03169507 17593 - - - -CNMG431-M3 48936 15328 - - - -CNMG431-M5 48992 16492 - - 46808 -CNMG431-MF2 49024 15051 - 15009 46752 -CNMG431-MF3 48577 - - - - -CNMG431-MF4 03096304 - - - - -

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

CNMG431W-FF2 - 15589 - - - -CNMG431W-MF2 - 15673 15672 - - -CNMG431W-MF4 03100383 - - - - -CNMG432-FF2 48937 14293 15718 15591 - -CNMG432-M3 48952 15333 15332 15330 46753 -CNMG432-M4 - - - - 46755 46720CNMG432-M5 48993 16097 16096 16095 46761 46721CNMG432-M6 49366 15109 15108 15104 46518 -CNMG432-MF2 49025 15061 15022 15021 46669 46465CNMG432-MF3 49026 - - - 46768 -CNMG432-MF4 03094139 18500 - - - -CNMG432-MF5 - 18562 18559 18488 - 46466CNMG432-MR6 - 18163 18220 - - -CNMG432-MR7 49029 15977 15976 - 46770 46722CNMG432-R4 48955 - - - - -CNMG432W-FF2 - 14294 15592 - - -CNMG432W-M3 - 15559 15557 15556 46566 -CNMG432W-M6 49370 15117 - - - -CNMG432W-MF2 49371 15676 15675 15674 46567 -CNMG432W-MF4 03100384 - - - - -CNMG432W-MF5 - 16747 16713 - - 46468CNMG433-M3 48953 15339 15338 15335 - -CNMG433-M4 - - - - 46771 46723CNMG433-M5 48994 16104 16099 16098 46772 46725CNMG433-M6 49372 15125 15122 15120 46519 -CNMG433-MF2 - 15063 15723 15722 - 46469CNMG433-MF3 49030 - - - - -CNMG433-MF4 03096309 16493 - - - -CNMG433-MF5 - 15987 15983 15981 - 46472CNMG433-MR6 - 16054 16034 - - -CNMG433-MR7 49032 16060 16059 16057 46773 46726CNMG433W-M3 - 15562 15561 15560 46568 -CNMG433W-M6 61347 15127 15126 - - -CNMG433W-MF2 - - - 15677 - -CNMG433W-MF4 03100385 - - - - -CNMG434-M3 - 15728 15724 - - -CNMG434-M5 49374 16106 16105 - - -CNMG434-M6 49375 15129 15128 - - -CNMG434-MF5 - 16064 16062 - - -CNMG434-MR7 49376 16068 16065 - 46670 46501CNMG542-M3 49377 15341 15340 - - -CNMG542-M5 48995 16108 16107 - 46774 -CNMG542-M6 03169826 - 03169651 - 03169653 -CNMG542-MF4 03096315 - - - - -CNMG542-MR7 49380 - - - - -CNMG543-M3 49381 15346 15345 15342 - -CNMG543-M5 48996 16496 16495 16494 46775 -CNMG543-M6 49382 15132 15131 15130 46520 -CNMG543-MF4 03096319CNMG543-MR7 49385 16073 16072 16071 46672 46502CNMG543W-M6 61387 15133 - - - -CNMG544-M3 03169502 03109502 03078008 - - -CNMG544-M5 48997 16113 16110 16109 46777 -CNMG544-M6 49386 15137 15136 15134 46521 -CNMG544-MR7 49387 16076 16075 16074 46569 -CNMG544W-M6 61388 15139 15138 - - -CNMG546-M6 61348 15143 15142 - 46570 -CNMG546-MR7 - - 16077 - - -CNMG642-M3 48954 15955 15954 - - -CNMG642-M5 48998 16116 16114 - - -CNMG642-MR7 49033 - - - - -CNMG643-M3 49388 15349 15348 - - -CNMG643-M5 48999 16502 16500 - 46779 -CNMG643-M6 49389 48973 48961 48951 - -CNMG643-MF4 03096325 - - - - -CNMG643-MR7 49034 16083 16081 16078 46780 -CNMG644-M3 49392 15353 15956 - - -CNMG644-M5 49000 16503 03169815 - 46781 -CNMG644-M6 49393 49007 48975 48974 46522 -CNMG644-MR7 49035 16529 16523 16086 46782 -CNMG646-M6 49394 49018 49010 49009 46523 -CNMG646-MR7 - 16089 16088 - - -CNMG866-MR4 49334 - - - - -CNMG866-MR7 49335 18769 18569 - - -CNMM432-R4 - 17064 17020 - - -CNMM433-R4 49396 17075 17026 16845 - -

20

DURATOMIC® - TP & TK GRADES

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

CNMM433-R6 49398 - - - - -CNMM433W-R4 - 16653 16690 - - -CNMM434-R4 - 16911 16908 16863 - -CNMM543-R4 49399 17062 16954 16932 - -CNMM543-R6 49402 - - - - -CNMM543-R7 49403 - - - - -CNMM543-RR6 - 17270 - - - -CNMM544-R4 49405 16982 17045 16948 - -CNMM544-R5 - - 17347 17444 - -CNMM544-R7 49406 17137 - 17136 - -CNMM544-RR6 - 17155 17323 - - -CNMM546-R7 - - - 17440 - -CNMM643-R4 49408 17028 16925 16889 - -CNMM643-R6 49409 - - - - -CNMM643-R7 49411 17165 - - - -CNMM643-RR6 - 17172 - - - -CNMM644-MR6 - - 18015 - - -CNMM644-R4 48990 16997 17081 16930 - -CNMM644-R5 - - 17175 - -CNMM644-R7 49413 17334 17181 - - -CNMM644-R8 49414 - - - - -CNMM644-RR6 49415 17350 - - - -CNMM644W-R7 03169509 16693 16669 - - -CNMM646-R4 49416 16966 16952 16903 - -CNMM646-R5 - - - 17277 - -CNMM646-R7 49417 17447 - 17192 - -CNMM646-RR6 - 17437 - 17206 - -CNMM646W-R7 03169510 16766 16658 16657 - -

DCMT21.50.5-F1 49419 19787 - - - -DCMT21.50.5-M3 - 20284 20236 - - -DCMT21.51-F1 49420 19974 19919 - - -DCMT21.51-M3 49421 20296 20285 - - -DCMT21.51-MF2 49422 14255 14963 - - -DCMT21.52-F1 49425 - 19789 - - -DCMT21.52-M3 49426 20291 20265 - - -DCMT21.52-MF2 49428 - - - - -DCMT32.50.5-F1 49429 19971 - - - -DCMT32.50.5-FF1 - 19684 - - - -DCMT32.50.5-M3 - 20288 20237 - - -DCMT32.50.5-MF2 49759 14256 14964 - - -DCMT32.51-F1 49430 20179 19983 15860 46651 46493DCMT32.51-FF1 03139177 19955 - - - -DCMT32.51-M3 48956 20298 20293 15904 46558 -DCMT32.51-MF2 49431 14257 14970 14966 - -DCMT32.52-F1 49432 20220 20182 15862 46652 46494DCMT32.52-FF1 03139176 19957 - - - -DCMT32.52-M3 49433 20299 20289 - 46559 -DCMT32.52-M5 49434 14278 14975 14971 - -DCMT32.52-MF2 49435 14258 14977 14976 - -DCMT32.53-F1 - 19939 19920 - - -DCMT32.53-M5 61340 14283 - - - -DCMT32.53-MF2 - 14259 - - - -DCMT431-M3 49437 20292 20266 - - -DCMT432-M3 49438 20294 20282 - - -DCMT433-M3 49439 20286 20283 - - -DCMX32.51W-F1 - 19307 19130 - - -DCMX32.52W-F1 - 19224 19308 - - -DNMA432 - - - - - 46697DNMA433-MR9 - - - - 46301 46300DNMA442 - - - - - 46698DNMA443 - - - - - 46699DNMA443-MR9 - - - - 46304 46302DNMG431-FF2 - 15594 15593 - - -DNMG431-M3 - 15407 15406 - 46571 -DNMG431-M5 49440 - - - - -DNMG431-MF2 - 15064 15028 15023 - -DNMG431-MF3 49441 - - - - -DNMG431-MF4 03096370DNMG432-FF2 49443 14296 15600 15599 - -DNMG432-M3 48958 15419 15417 15411 46572 -

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

DNMG432-M5 49001 16238 16237 16223 46573 -DNMG432-M6 49444 15182 15180 - - -DNMG432-MF2 49446 15065 15031 15029 - -DNMG432-MF3 49447 - - - - -DNMG432-MF4 03096375 - - - - -DNMG432-MF5 - 18251 18100 - - 46473DNMG433-M3 49449 15450 15445 15427 46574 -DNMG433-M5 49002 16596 16595 - - -DNMG433-M6 49451 15184 15183 - - -DNMG433-MF2 - 15066 - - - -DNMG433-MF4 03096378 - - - - -DNMG433-MF5 - 18235 18025 - - -DNMG434-M3 61351 - - - - -DNMG434-M6 61350 15188 - - - -DNMG441-FF2 - 15606 15605 - - -DNMG441L-UX - 17578 17510 - - -DNMG441-M3 48959 15455 15454 - 46575DNMG441-M5 49458 16251 - - - -DNMG441-MF2 49038 15067 15729 - - -DNMG441-MF3 49767 - - - - -DNMG441-MF4 03096380 - - - - -DNMG441R-UX - 17597 17541 - - -DNMG442-FF2 - 14297 15612 15611 - -DNMG442L-UX - 17585 17559 - - -DNMG442-M3 48960 15463 15461 15458 46576DNMG442-M5 49003 16267 16266 16258 46783 46732DNMG442-M6 49790 15190 15189 - 46524DNMG442-MF2 49052 15068 15733 15732 46673 46474DNMG442-MF3 49053 - - - - -DNMG442-MF4 03096381 18104 - - - -DNMG442-MF5 - 18238 18225 18222 - 46475DNMG442-MR7 - - 16597 - - -DNMG442R-UX - 17596 17566 - - -DNMG443-M3 - 15466 15734 15464 46577 -DNMG443-M5 49004 16606 16605 16604 46785 46734DNMG443-M6 49462 15204 15192 15191 46525 -DNMG443-MF2 - 15069 15737 15736 46578 -DNMG443-MF3 48962 - - - - -DNMG443-MF4 03096383 - - - - -DNMG443-MF5 - 18164 18230 18046 - -DNMG443-MR7 49465 16412 16408 46579 -DNMG444-M3 - 15475 15738 - - -DNMG444-M5 49005 16610 16608 16607 - -DNMG444-M6 49466 15211 15206 - - -DNMG444-MF2 03169655 - 03169656 - - -DNMG444-MF5 - 18181 - - - -DNMG542-M5 61598 - - - - -DNMG543-M6 61599 - - - - -DNMM442-R4 49467 16801 16797 - - -DNMM443-R4 49468 16832 16833 16802 - -DNMM444-R4 - 16831 16819 - - -DNMP431-M3 48957 - - - - -DNMP431-MF2 49036 - - - - -DNMU330.5-M3 61352 15483 15479 - - -DNMU331-FF2 49470 14298 15619 - - -DNMU331-M3 48963 15485 15739 - 46580 -DNMU331-MF2 49054 15070 15034 15033 - 46477DNMU331-MF4 03096389 - - - - -DNMU331-MF5 - 18182 - - - -DNMU332-FF2 49475 14299 15621 15620 - -DNMU332-M3 48964 15504 15500 15496 46581 -DNMU332-M5 - - 16277 - 46582 -DNMU332-M6 49479 49037 49028 - 46516 -DNMU332-MF2 49055 15071 15743 15741 46674 46478DNMU332-MF4 03096392DNMU332-MF5 - 18231 - - - -DNMU333-M3 - - 15510 15509 46583 -DNMU333-M5 - - 16280 - - -DNMU333-M6 49484 49070 49063 - 46517 -DNMU333-MF2 - 15072 - - - -DNMU333-MF5 - 18114 - - - -DNMX331W-MF2 - 15695 15694 - - -DNMX332W-MF2 49485 15697 15696 - - -DNMX432W-M3 - - 15563 - - -DNMX433W-M3 - - 15565 - - -DNMX443W-M3 - - 15570 15569 - -

21

DURATOMIC® - TP & TK GRADES

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

KNUX160405L-11 49336 18923 18868 - - -KNUX160405R-11 49338 18948 18869 - - -KNUX160410L-11 - 18870 - - - -KNUX160410R-11 - 18871 - - - -

LNMX191940-MF - 18828 18889 - - -LNMX191940-MR - 18846 18829 - - -LNMX191940-R2 - - 18872 18848 46616 -LNMX191940-RR94 - - 18894 18849 46617 -LNMX301940-MF - 18873 18850 - - -LNMX301940-MR - 18854 18852 - - -LNMX301940-R2 - - 18856 18855 46618 -LNMX301940-RR94 - - 18857 18875 - -LNMX301940-RR97 - - 18860 18859 - -LNMX401432-RR93 - - 18862 18882 - -LNMX401432-RR96 - 18864 18863 - - -LNMX501432-RR96 - 18867 18866 - - -

RCMT0602M0-F1 49487 15863 - - - -RCMT0602M0-M3 61341 15906 - - - -RCMT0803M0-F1 61342 15864 - - - -RCMT0803M0-M3 49488 15908 15907 - 46560 -RCMT10T3M0-F1 49489 15865 - - - -RCMT10T3M0-M3 49490 15911 15909 - 46561 -RCMT1204M0-F1 49491 15867 15866 - 46544 -RCMT1204M0-M3 49493 15913 15912 - 46662 46508RCMT1204M0-R2 61343 - - - - -RCMT1606M0-F1 49495 15870 15869 15868 - -RCMT1606M0-M3 49497 15916 15915 15914 - -RCMT2006M0-R3 03084618RCMX100300-RR94 48965 - - - - -RCMX120400-RR94 48966 20318 - - - -RCMX160600-RR94 49498 20315 20313 - - -RCMX200600-R2 - 20310 - 20309 - -RCMX200600-R3 - 03084610 03084609 03084608 - -RCMX200600-RR93 - 03084621 03084620 03084619 - -RCMX250700-R3 - 03084615 03084614 03084613 - -RCMX250700-RR93 - 03084625 03084624 03084623 - -RCMX320900-R3 03084617RCMX320900-RR93 - 03084629 03084628 03084627 - -RCMX200600-RR94 49328 20314 20317 20316 - -RCMX200600-RR97 - 20312 - 20311 - 46614RCMX250700-R2 - 20334 - 20333 - -RCMX250700-RR94 48967 20341 20345 20349 46621 -RCMX250700-RR97 - 20335 - 20342 - 46615RCMX320900-R2 - 20325 - 20321 - -RCMX320900-RR94 49329 20336 20340 20347 46622 -RCMX320900-RR97 - 20330 - 20328 - -RNMA43 - - - - 46627 -RNMG43-M3 49499 15528 15527 - - -

SCMT09T308-F1 - - - - 46545 -SCMT09T308-M3 - - - - 46663 46509SCMT1268-RR97 - - - 20339 - -SCMT2.522-M3 49646 15918 - - - -SCMT21.51-M3 49645 15917 - - - -SCMT32.51-F1 49649 15871 - - - -SCMT32.51-M3 49650 15919 - - - -SCMT32.51-MF2 - 14260 - - - -SCMT32.52-F1 49652 15880 - - - -SCMT32.52-M3 49661 15927 15921 - - -SCMT32.52-M5 03169819 03169504 - - - -SCMT32.52-MF2 49662 14261 - - - -SCMT32.53-F1 49663 - - - - -SCMT32.53-M5 03169828 - - - - -SCMT432-F1 49666 15884 - - - -

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

SCMT432-M3 49668 15946 15929 - 46664 46510SCMT432-M5 49669 14285 03169501 14978 46562 -SCMT432-MF2 49672 14262 - - - -SCMT433-F1 - - 15886 - - -SCMT433-M3 - - - - 46563 -SCMT866-RR97 - - - 20337 - -SCMT866T-RR97 - 20338 - - - -SNMA322 - - - - - 46495SNMA432 - - - - 46813 46700SNMA432-MR9 - - - - 03128756 03128755SNMA433 - - - - - 46701SNMA433-MR9 - - - - 46306 46305SNMA434 - - - - - 46496SNMA434-MR9 - - - - 46308 46307SNMA543 - - - - 46628 46497SNMA544-MR9 - - - - 46312 46309SNMA643 - - - - - 46705SNMA644 - - - - 46814 46706SNMG321-MF2 18499 - - - -SNMG322-M5 49006 18259 - - - -SNMG322-MF2 - 18258 - - - -SNMG431-M3 49500 15529 - - - -SNMG432-M3 48968 15531 15530 - 46584 -SNMG432-M5 49008 16611 - - 46786 46735SNMG432-M6 49514 15280 15272 - - -SNMG432-MF2 49071 15073 15744 - - -SNMG432-MF4 03096541 - - - - -SNMG432-MR7 49516 16420 16414 - - -SNMG433-M3 48969 15534 15533 - - -SNMG433-M5 49011 16303 16299 - 46787 -SNMG433-M6 49517 15307 15297 - - -SNMG433-MF2 - 15074 15035 - - -SNMG433-MF4 03096544 - - - - -SNMG433-MR7 49058 16446 - - 46789 -SNMG434-M3 61354 15536 15535 - - -SNMG434-M5 49519 16312 16304 - - -SNMG434-M6 03169827 - 03169654 - - -SNMG434-MR7 - 16470 - - - -SNMG542-M5 - 16316 - - - -SNMG543-M3 61355 15538 15537 - - -SNMG543-M5 49523 16345 16320 - - -SNMG543-M6 49524 15313 15312 - - -SNMG543-MR6 - 18210 - - - -SNMG543-MR7 49525 16475 - - 46585 -SNMG544-M5 49526 16368 16360 16346 - -SNMG544-M6 49527 15319 15316 15314 - -SNMG544-MR7 - 16476 - - 46586 -SNMG643-M3 49528 15539 - - - -SNMG643-M5 49012 16612 - - 46790 -SNMG643-M6 49530 49109 49080 49073 - -SNMG643-MR7 49533 16489 - - - -SNMG644-M3 - 15540 - - - -SNMG644-M5 49013 16622 16614 16407 - -SNMG644-M6 49536 49147 49143 49126 46526 -SNMG644-MR7 49059 16637 16636 16490 - -SNMG646-M6 61359 49158 49156 49155 46527 -SNMG646-MR7 - 16491 - - - -SNMG866-MR7 49060 18827 - 18617 - -SNMM432-R4 49540 - - - - -SNMM433-R4 49541 16775 - - - -SNMM543-R4 48970 18475 - - - -SNMM544-R4 48971 18507 - 18271 - -SNMM546-R7 - 17340 - - - -SNMM643-R4 49544 16792 - - - -SNMM643-R6 49545 - - - - -SNMM643-R7 - 17286 - - - -SNMM643-R8 49550 - - - - -SNMM643-RR6 49551 - - - - -SNMM644-R4 49784 16793 16784 16770 - -SNMM644-R5 - 17207 - - - -SNMM644-R6 49786 - - - - -SNMM644-R56 61360 - - - - -SNMM644-R57 - 17291 17408 - - -SNMM644-RR6 - 17213 - - - -

22

DURATOMIC® - TP & TK GRADES

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

SNMM644W-R7 - 16694 - - - -SNMM646-57 48976 - - - - -SNMM646-R4 49555 16790 - 16771 - -SNMM646-R5 - 17215 - - - -SNMM646-R57 61361 - - 17229 - -SNMM646-R7 - 17346 - 17235 - -SNMM646-RR6 - 17315 - - - -SNMM646W-R7 - 16663 - - - -SNMM856-56 49341 - - - - -SNMM856-57 49342 - - - - -SNMM856-R56 - 18567 - - - -SNMM856-R57 - 18621 - - - -SNMM856-R7 49343 18813 - 18627 - -SNMM856-RR6 - 18676 - - - -SNMM856-RR9 49344 - - - - -SNMM866-R68 - 18633 - 18629 - -SNMM866-R7 49345 18821 - 18634 - -SNU433 - - - - 46629 -SPMR321-F1 - 18283 - - - -SPMR322-F1 - 18481 - - - -SPMR421-F1 - 18484 - - - -SPMR422-F1 - 17626 - - - -SPMR422-M3 - 17735 - - - -SPMR423-F1 - 18448 - - - -SPU421 - 17900 - - - -SPU422 - 17997 - - - -SPU633 - 17870 - - - -SPU634T - 17835 - - - -

TCGX32.50.5WL-F1 - 15887 - - - -TCGX32.50.5WR-F1 - 15888 - - - -TCMT16T312-M5 - - - - 46547 -TCMT21.50.5-F1 49676 - - - - -TCMT21.51-F1 49680 15890 15889 - - -TCMT21.51-MF2 49681 14263 - - - -TCMT21.52-F1 49682 15892 15891 - - -TCMT21.52-MF2 49683 14264 - - - -TCMT32.50.5-F1 49684 - - - - -TCMT32.51-F1 49685 15894 15893 - - -TCMT32.51-M3 49686 15948 15947 - 46564 -TCMT32.51-MF2 49694 14265 - - - -TCMT32.52-F1 49699 15896 15895 - - -TCMT32.52-M3 49701 15951 15949 - 46665 46513TCMT32.52-M5 61344 14286 - 14979 46546 -TCMT32.52-MF2 49702 14266 - - - -TCMT32.53-F1 49703 - 15897 - - -TCMT32.53-M5 49704 14288 - - - -TCMT432-M3 49711 15953 15952 - - -TCMX32.52W-F1 - 15903 15902 - - -TNMA331 - - - - - 46707TNMA332 - - - - 46815 46708TNMA333 - - - - 46816 46710TNMA333-MR9 - - - - 46315 46314TNMA334 - - - - - 46498TNMA334-MR9 - - - - 46317 46316TNMA432 - - - - - 46711TNMA433 - - - - 46817 46712TNMA434 - - - - - 46713TNMA434-MR9 - - - - 46319 46318TNMG221-MF2 15746 - - - -TNMG322-M5 49014 - - - - -TNMG322-MF3 49556 - - - - -TNMG331-FF2 - 15658 15623 - - -TNMG331L-UX - 17592 - - - -TNMG331-M3 48977 15541 15747 - 46791 -TNMG331-M5 49558 15957 - - - -TNMG331-MF2 49061 15076 15748 - - -TNMG331-MF3 49062 - - - - -TNMG331-MF4 03096566 - - - - -TNMG331R-UX - 17602 - - - -TNMG332-FF1 03169508 - - - - -

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

TNMG332-FF2 - 15659 15749 - - -TNMG332L-UX - 17591 - - - -TNMG332-M3 48978 15546 15751 15750 - -TNMG332-M4 - - - - 46588 -TNMG332-M5 49015 15966 15964 15960 46792 46740TNMG332-M6 49560 15323 15320 - -TNMG332-MF2 49064 15077 15038 15037 - -TNMG332-MF3 49065 - - - - -TNMG332-MF4 03096568 - - - - -TNMG332-MF5 - 18253 18240 - - -TNMG332-MR7 49568 - - - - -TNMG332R-UX - 17594 - - - -TNMG333-M3 48979 15548 15752 - - -TNMG333-M5 49016 16640 16639 16638 46793 -TNMG333-M6 49569 15326 15324 - - -TNMG333-MF2 - 15078 15755 - - -TNMG333-MF4 03096571 - - - - -TNMG333-MF5 - 18136 18211 - - -TNMG333-MR7 49066 - 16646 - - -TNMG334-M5 - - - - 46589 -TNMG431-M5 49574 15967 - - - -TNMG431-MF2 - 15079 - - - -TNMG431-MF3 49067 - - - - -TNMG432-M3 48991 15549 15757 - - -TNMG432-M5 49017 16649 16648 15968 46794 -TNMG432-M6 49575 49161 49160 49159 46528 -TNMG432-MF2 - 15080 15041 - - -TNMG432-MF3 49576 - - - - -TNMG432-MF4 03096575 - - - - -TNMG432-MR7 49579 - - - - -TNMG433-M3 49580 15553 15550 - - -TNMG433-M5 49019 15971 15970 15969 - -TNMG433-M6 49581 49164 49163 49162 46529 -TNMG433-MF4 03096579 - - - - -TNMG433-MR7 49584 - - - - -TNMG434-M5 49585 15974 15973 15972 - -TNMG434-M6 49586 49175 49166 49165 - -TNMG542-M5 49347 - - - - -TNMG543-M3 49348 18792 - - - -TNMG543-M5 49349 18826 18677 - - -TNMG543-M6 49588 49177 49176 - - -TNMG543-MR7 49354 18684 - - - -TNMG544-M5 49355 18669 18824 - - -TNMG544-M6 49589 49179 49178 - - -TNMG544-MR7 49357 18825 - - - -TNMG666-MR7 49358 18690 - - - -TNMM331-R6 49590 - - - - -TNMM332-R4 49592 16795 - - - -TNMM333-R4 - 18493 - - - -TNMM432-R4 49594 16796 - - - -TNMM433-R4 49595 16794 16791 - - -TNMM434-R4 49598 16789 16800 - - -TNMM434-R6 49359 - - - - -TNMX332W-M3 - 15572 15571 - - -TNMX333W-M3 - - 15573 - - -TPMR221-F1 - 17643 - - - -TPMR222-F1 - 18503 - - - -TPMR321-F1 - 17644 17605 - - -TPMR321-M3 - 17750 - - - -TPMR322-F1 - 17611 17617 - - -TPMR322-M3 - 17757 - - - -TPMR432-M3 - 17771 - - - -TPMR433-M3 - 17694 - - - -TPU221 - - - - 46822 -TPU222 - - - - 46823 -TPU321 49714 17915 - - 46633 -TPU322 49716 18013 - - 46634 -TPU323 - - - - 46635 -TPU431 - 17885 - - - -TPU432 - 17925 - - 46636 -TPU433 - 18487 - - - -

23

DURATOMIC® - TP & TK GRADES

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

WNMG333-MF2 - 15084 - - - -WNMG333-MF4 03096591 - - - - -WNMG333-MF5 - 18087 18212 - - -WNMG333W-M3 - 15577 15576 - - -WNMG431-FF2 - 14300 15667 - - -WNMG431-M3 48985 15395 15764 - 46801 -WNMG431-MF2 - 15085 15765 - - -WNMG431-MF4 03096592 - - - - -WNMG431W-MF2 - 15709 - - - -WNMG432-FF2 - 14301 15668 - - -WNMG432-M3 48986 15397 15767 15766 46802 -WNMG432-M4 - - - - 46591 -WNMG432-M5 49022 16589 16567 16560 46803 46742WNMG432-M6 49603 15151 15149 15145 46530WNMG432-MF2 - 15089 15044 - - 46479WNMG432-MF3 49074 - - - - -WNMG432-MF4 03096594 18232 - - - -WNMG432-MF5 - 18257 18239 18144 - 46480WNMG432-MR6 - 18213 18202 - - -WNMG432-MR7 49075 16090 - - 46804 46747WNMG432W-M3 - 15582 15580 15578 46592 -WNMG432W-M6 61364 15155 15152 - - -WNMG432W-MF2 - 15716 15712 - - -WNMG432W-MF4 03100388WNMG432W-MF5 - 16688 16687 - - -WNMG433-M3 48987 15402 15769 15768 46805 -WNMG433-M4 - - - - 46593 -WNMG433-M5 49023 16592 16591 16590 46806 46749WNMG433-M6 49607 15159 15158 15156 46532 -WNMG433-MF2 - - 15045 - - 46482WNMG433-MF4 03096596 18203 - - - -WNMG433-MF5 - 18234 18161 18207 - -WNMG433-MR6 - - 18215 - - -WNMG433-MR7 49076 16594 16593 - 46807 46750WNMG433W-M3 - 15586 15585 15584 46594 -WNMG433W-M6 61389 15163 15160 - - -WNMG433W-MF4 03100389WNMG434-M3 - 15403 - - - -WNMG434-M5 49611 16205 16189 16185 - -WNMG434-M6 49614 15172 15165 15164 46533 -WNMG434-MF5 - 18250 - - - -WNMG434-MR7 49615 16094 16093 - - -WNMG442-M5 49616 - - - - -WNMG443-M5 49617 16210 16207 - - -WNMG443-M6 49620 15177 15175 15173 46534 -WNMG444-M5 49621 16221 16216 - - -WNMG444-M6 - - 15178 - 46536 -WNMM432-R6 49640 - - - - -

DESCRIPTION

GRADES (PRODUCT NUMBER)

TP35

01

TP25

01

TP15

01

TP05

01

TK15

01

TK05

01

VBMT21.50.5-F1 49717 - - - - -VBMT21.51-F1 49718 - - - - -VBMT21.52-F1 03169505 - - - - -VBMT220.5-F1 49719 - - - - -VBMT221-F1 49720 19952 - - - -VBMT222-F1 - 19673 - - - -VBMT330.5-F1 49721 19953 - - - -VBMT330.5-MF2 49722 - - - - -VBMT331-F1 48980 20223 19973 - - -VBMT331-M3 49723 20300 20290 - 46667 46514VBMT331-MF2 49724 14268 14983 14981 - -VBMT332-F1 49725 20235 20227 - 46654 46500VBMT332-M3 49727 20308 20295 20287 46565 -VBMT332-M5 49736 14291 14986 14985 46549 -VBMT332-MF2 49737 14269 14989 14988 - -VBMT333-F1 49738 19862 20126 - - -VBMT333-M3 48981 20297 20267 - - -VBMT333-MF2 - 14270 14994 14993 - -VNMA332 - - - - 46619 -VNMG330.5-FF2 - 14302 15669 - - -VNMG331-FF1 - - 17571 - - -VNMG331-FF2 49622 14303 15670 - - -VNMG331-M3 48988 15512 15511 - 46595 -VNMG331-MF2 49624 15090 15046 - - -VNMG331-MF3 49625 - - - - -VNMG331-MF4 03096607 - - - - -VNMG332-FF2 49630 14304 15671 - - -VNMG332-M3 48989 15515 15770 15514 46596 -VNMG332-MF2 49631 15092 15049 15048 - -VNMG332-MF3 49637 - - - - -VNMG332-MF4 03096611VNMG333-M3 03169661 03169658 03169659 03169660 03169662 -VNMG333-MF2 - 15100 15050 - - -VNMU130408-MF2 - - - - 46609 -VNMU2.531-M3 49641 15520 15516 - - -VNMU2.531-MF2 49642 47502 47501 - - -VNMU2.532-M3 49643 15526 15524 15522 - -VNMU2.532-M6 61365 49181 49180 - - -VNMU2.532-MF2 49644 47505 47504 - - -

WCMT32.52-F1 49755 19956 - - - -WCMT32.52W-F1 - 18970 - - - -WNMA332 - - - - 46818 46714WNMA333 - - - - 46819 -WNMA432 - - - - 46820 46715WNMA432-MR9 - - - - 46336 46331WNMA433 - - - - 46821 46716WNMA433-MR9 - - - - 46338 46337WNMA434 - - - - 46630 46717WNMA434-MR9 - - - - 46340 46339WNMG330.5-M3 - 15373 - - -WNMG331-FF2 - 15661 15660 - - -WNMG331-M3 48982 15374 15759 - - -WNMG331-MF2 49068 15082 15760 - - -WNMG331-MF5 - 18140 - - - -WNMG331W-FF2 - 15662 - - - -WNMG331W-MF2 - 15704 15703 - - -WNMG332-FF2 - 15665 15664 - - -WNMG332-M3 48983 15376 15763 15761 46795WNMG332-M5 49020 16555 16550 16546 46798 46741WNMG332-MF2 49069 15083 15043 - - -WNMG332-MF3 49072 - - - - -WNMG332-MF4 03096590 18191 - - - -WNMG332-MF5 - 18256 - - - -WNMG332W-FF2 - 15666 - - - -WNMG332W-M3 61362 15575 15574 - 46590 -WNMG332W-MF2 - 15708 15706 - - -WNMG332W-MF5 - 16696 16683 - - -WNMG333-M3 48984 15386 15382 15378 - -

24

DURATOMIC® - TP & TK GRADES

25

TECHNICAL INFORMATION

INDIVIDUAL CUTTING DATA ON THE INSERT BOXThe box features cutting data specific to the parts within:• This cutting data for WNMG433-M6 can be used as an example for

referencing the SMG steel classification. It comes from the same one-source cutting data service that is used for box label data, data in My Pages and catalogs.

• The SMG-based box label incorporates a QR code to provide a direct link to a product-specific cutting data page in My Pages. Cutting data comes from a single source and is populated across all Seco platforms for consistency.

Marking for main application area (open circle for secondary application)

Recommended depth of cut, feed rateand cutting speed for Seco Material Group

WNMG080412-M6, TP1501WNMG433-M6

QTY 10

02959875

EDP 15158DU

RAT

OM

IC®

P

M

K

N

S

H

P4 P5

ap

f

Vc

1,3

0.05

0,12

0.0048

385

1250

mm

in

mm/rev

in/rev

m/min

sf/min

1,3

0.05

0,12

0.0048

510

1675

SMG (v2)

Steel

Stainless steel

Cast iron

Finishing Medium- rough

machining

Rough machining

Chipbreaker

CUTTING DATA ONLINENow cutting data is just a few clicks away. Gain quick and easy access to this useful information through our website where standard products are easily searchable by description, grade, trademark or product number. Simply enter your query in the search box at the top of the screen and upon selection of a product the cutting data is provided with the other product details. Initially the data is populated based on default values but you can modify different criteria to fit your requirements.

• Gain instant access to advanced cutting data

• Easily adjust cutting data by material and cutting method

• Or modify based on a variety of other options like desired number of passes, feed/tooth, RPM, machine power or torque

SECOTOOLS.COM

25

DURATOMIC® MAKES THE WORLD TURN

27

DURATOMIC® AT YOUR FINGERTIPS WITH MY PAGESMy Pages is your digital portal that puts the power of Seco at your fingertips. Anything is possible when it comes to our broad selection of general turning grades and chipbreakers, including our newest range of Duratomic chrome technology. Supporting inserts of different shapes, sizes and thicknesses, we developed this application with one goal in mind: to boost the productivity and tool life in your turning applications. My Pages brings together a wide range of tools under a single interface, while offering the opportunity for seamless integration of new capabilities in the future. Covering all material groups, this comprehensive range allows you to achieve your goals in terms of material removal rates, tool life and surface finish. It works to meet your specific needs and helps you to achieve cost and time savings.

• Gain instant access to specifications, cutting data and CAD models on every standard Seco product

• Use Suggest to get tool recommendations based on your part specifications and material

• Quickly generate CNC code for threading and send it to your machine• Easily find tips on how to optimize your machining operations

Register today at SECOTOOLS.COM

28

To find an Authorized SECO Distributor near you, please refer

to our Distributor Locator:

SECOLOCATOR.COM

For technical assistance, call: 1-800-TEC-TEAM

For customer support, call: 1-248-528-5220

SECO TOOLS, LLC

NORTH AMERICAN HEADQUARTERS

2805 Bellingham Drive

Troy, MI 48083

248-528-5200

SECOTOOLS.COM

P-1908-2500 GT19-115Copyright © 2019 Seco Tools, LLC Printed in USA. All rights reserved.

Follow Seco Tools on Twitter, Facebook,

YouTube and Blogger. Stay up to date

on new products and technology,

special events, promotions and more.

@SECOTOOLSUS

LEARN MORE AT: DURATOMIC.COM