Disassemble N011

U100（MS-N011）Disassemble SOP

■ 1、Battery Pack

■ 2、LOWER CASE ASSY

■ 3、WLAN and RAM Module

■ 4、HDD Module ASSY

■ 5、THERMAL-KIT And CPU Module

■ 6、Disassemble LCD and UPCASE

■ 7、UP CASE ASSY

■ 8、LCD MODULE ASSY


■ 1、Battery Pack

1-1：Push the battery Unlock button in the direction shown below;

1-2：Push the battery Release button in the direction shown below, then slide the battery pack out of the slot;

NO. Part Name Part No. Qty

1 Battery Pack S9N-1832300-SJ3 1

U100（MS-N011）Disassemble SOP ■ 2、LOW CASE ASSY

2-1：Remove 9pcs M2*2.5mm screws which is on Bottom Door with Screw Driver.

Note：driver torque is 1.8-2.2Kgf-cm(3-9) Note：Screw driver torque is 3.0-3.5Kgf-cm (1-2)

7

5

8 9

6

4

2

3

1

2-2：Remove Bottom Door Assy;


1 Screw E43-1255007-H29 9

2 LOW CASE ASSY 307-011D411-TA2 1

U100（MS-N011）Disassemble SOP ■ 3、WLAN and RAM Module

3-1： Remove 1pcs M2*3mm screw ,Then Remove ANTENNA/HIGH-TEK/R-L in the direction shown below;

Note：Screw driver torque is 1.0-1.4Kgf-cm

1

3-2：Remove WIRELESS CARD in the direction shown below;


1 WIRELESS CARD 605-6894-A10 1

2 Screw E43-1203003-H29 1


3-3：Push the RAM locks away;

3-4：Take off the RAM Module as below;


1 RAM Module S7C-S347701-T10 1


■ 4、HDD Module ASSY 4-1：Remove 1pcs M2*2.5mm screw, Then RemoveHDD Module Assy in the direction shown below;


1


1 screw E43-1255007-H29 1


4-2：Remove 2pcs M3*3.5mm screws ,Then Remove HDD Bracket in the direction shown below;


2

1


1 Screw E43-1303502-H29 2

2 HDD Bracket Assy 307-0110111-A89 1

3 HDD MODULE ASSY S71-2408505-W36 1


■ 5、THERMAL-KIT And CPU Module 5-1：Remove 1pcs M2*2.5 screw, CPU Fan sink Cable and Remove HEATSINK in order.


1


1 screw E43-1255007-H29 1

2 CPU FAN MOUDULE OE3-0800020 1

HEATSINK E31-0800720-TA9 1


■ 6、Disassemble LCD and UPCASE 6-1: Remove LCD LVDS Cable 、CMOS CABLE、 BLUETOOTH CABLE、 MICROPHONE Cable、

Then Remove SPEAKER MODULE Cable in the direction shown below;


6-2：Remove LCD LVDS Cable 、CMOS CABLE、 BLUETOOTH CABLE、 MICROPHONE Cable、

Then Remove SPEAKER MODULE Cable in the direction shown below;


1 CMOS CABLE K10-3006060-H39 1

2 COAXIAL CABLE K19-3024001-V03 1

3 BLUETOOTH CABLE K10-3008069-H39 1


6-3：Remove 4pcs M2*2.5mm screws which is use screw driver;


21


1 screw E43-1255007-H29 2


6-4：Remove LCD MODULE ASSY in the direction shown below;


■ 7、UP CASE ASSY

7-1：Remove 1pcs M2*3mm Screw, Remove FFC Cable (TO Button) in the direction shown below;


1

7-2：Remove M/B ,Then Remove DIS BATTERY in the direction shown below;


1 Screws E43-1203003-H29 1

2 DIS BATTERY D06-0100300-H04 1


7-3：Remove Keyboard in the direction shown below;

7-4：Remove Keyboard Cable in the direction shown below;


1 Keyboard S1N-1UUS361-SA0 1


7-5：Remove Touchpad FFC (To Button)，Remove Touchpad Module in the direction shown below;


1 Touchpad Module S78-3700170-SD2 1

2 Touchpad FFC (To Button) K1C-1012026-J36 1


7-6：Remove Bluetooth Antenna ,Then Remove BLUETOOTH CABLE in the direction shown below;

7-7：Remove BLUETOOTH MODULE in the direction shown below;


1 BLUETOOTH MODULE 605-6837D-050 1

2 BLUETOOTH CABLE K10-3008069-H39 1


7-8：Remove speaker in the direction shown below;


1 Speaker S33-A010300-F33 1


7-9：Remove MAGNET in the direction shown below;


1 MAGNET E2M-0110611-SF7 2

2 M/B 607-N0111-C10 1

3 UP CASE ASSY 307-011C411-TA2 1


■ 8、LCD MODULE ASSY 8-1：Remove 4pcs LCD Rubbers ,Then Remove 4pcs M2*2.5mm screws in the direction shown below;

Note：Screw driver torque is 2.0~.2.2kgf*cm

4

2

3

1

4 3

2 1


1 Screw E43-1255007-H29 4

2 LCD SECOND RUBBER E2Y-0112711-Y40 2

3 LCD RUBBER E2Y-0112611-Y40 4


8-2：Remove LCD Bezel in the direction shown below;


1 LCD BEZEL 307-011B411-TA2 1


8-3：Remove 2pcs M2*2.5mm screws , Then Remove Hinge LCD_HINGE_CAP;


1 2

1 2

8-4：Remove Hinge Cap-L-R in the direction shown below;

1 2


1 Hinge_Left E2M-0110211-G60 1

2 Hinge_Right E2M-0110111-G60 1

3 LCD_HINGE_CAP E2P-0110111-TA2 2

4 Screw E43-1255007-H29 2


8-5：Remove 2pcs M2*3mm screws, Then Remove 2pcs magnet in the direction shown below;;


1

2


1 Screw E43-1203003-H29 2

2 MAGNET E2M-0110811-SF7 2


8-6：Remove Display Module in the direction shown below;


8-7：Remove CMOS CABLE，Remove CMOS Camera Module in the direction shown below;


1 CMOS Camera Module S1F-0001200-AF5 1


8-8：Remove2PCS WIRELESS ANTENNA in the direction shown below;


1 WIRELESS ANTENNA_R S79-1800990-V03 1

2 WIRELESS ANTENNA_L S79-1800980-V03 1


8-9：Remove MICROPHONE in the direction shown below;


1 MICROPHONE S34-2100680-F33 1

2 LCD Cover Assy 307-011A411-TA2 1


8-10：Remove Coaxial Cable in the direction shown below;


1 LCD LVDS Cable K19-3024001-V03 1

2 ANTI-GLARE OS1-N011001 1


8-11：Remove 4pcs M2*3mm Screws, Then Remove LCD Bracket in the direction shown below;


2 4

3 1

2 1


1 Screw E43-1203003-H29 4

2 DISPLAY MODULE S1J-100A002-H34 1

3 LCD-Bracket E2M-0110311-A89 2

（MS-N011）screws specification

Photo Screw specification label

(M2*3mm)white

(M2*2.5 mm) black


■ 1、LOW CASE ASSY 9pcs screws，

specification：

Photo Screw specification Label

(M2*2.5 mm) black


■ 2、 wireless 1pcs screw，

specification：


(M2*3mm)white


■ 3、HDD、NB 5pcs screws，

specification：

1


(M2*2.5 mm) black

(M2*3mm)white


■ 4、 LCD Bezel total 4pcs screws，

specification：


(M2*2.5 mm) black


■ 5. LCD Bracket total 8pcs screws，specification：


(M2*2.5 mm) black

(M2*3mm)white

Documents

Disassemble N011