Upload
nickelhand
View
165
Download
1
Embed Size (px)
Citation preview
GX630 (MS-1652)Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■ 3、THERMAL-KIT And CPU Module
■ 4、RAM、WLAN And TUNER Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■ 10、LCD MODULE ASSY
GX630(MS-1652)Disassemble SOP
■ 1、Battery Pack
1-1:Push the battery Unlock button as below;
1-2:Push the battery Release button as below, then slide the battery pack out of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-0366200-SB3 1
GX630(MS-1652)Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1:Remove 2pcs M2.5*5mm Screws ; Note:Screw driver torque is 2.0~2.5kgf.cm
2-2:Remove Bottom Door Assy as below;
GX630(MS-1652)Disassemble SOP
2-3:Remove SIM Card Door as below;
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 2
2 SIM CARD DOOR E2P-6510511-Y31 1
2 BOTTOM DOOR ASSY 307-651J411-Y31 1
GX630(MS-1652)Disassemble SOP
■ 3、THERMAL-KIT And CPU Module
3-1:Remove 7pcs SPING Screws and 2pcs M2.5*5mm screws, Then Disconnect CPU Fan sink Cable; Note:Screw driver torque is 2.0~2.5kgf.cm
2 4
3 1
9
7 5
8
6
3-2:Remove CPU Fansink;
NO. Part Name Part No. Qty
1 screw E43-1255001-G68 2
2 CPU FANSINK E32-1300112-F05 1
GX630(MS-1652)Disassemble SOP
3-3:Open CPU lock as below;
3-4:Remove CPU Module;
NO. Part Name Part No. Qty
1 CPU Module A10-K82G2F6-A08 1
GX630(MS-1652) Disassemble SOP 3-5:Remove 2pcs M2.5*5mm Screws;
Note:Screw driver torque is 1.8~2.0kgf.cm
3-6:Remove VGA Card Module;
NO. Part Name Part No. Qty
1 VGA CARD Module 602-V114-020 1
2 Screw E43-1255001-G68 2
GX630(MS-1652)Disassemble SOP
■ 4、RAM、WLAN And TUNER Module
4-1:Push RAM Slot Fastener as below;
4-2:Remove RAM Module;
NO. Part Name Part No. Qty
1 RAM Module S7C-S357701-T10 2
GX630(MS-1652)Disassemble SOP
4-3:Remove WLAN Card Antenna, Then Remove 1pcs M2*3mm Screw; Note:Screw driver torque is 1.5~2.0kgf.cm
4-4:Remove WLAN Card Module;
NO. Part Name Part No. Qty
1 WLAN CARD Module S57-3800010-T46 1
2 Screw E43-1203007-G68 1
GX630(MS-1652)Disassemble SOP
4-5:Remove Tuner Antenna, Then Remove 1pcs M2*3mm; Note:Screw driver torque is 1.5~2.0kgf.cm
4-6:Remove Tuner Module;
NO. Part Name Part No. Qty
1 TUNER Module S36-0000610-K45 1
2 Screw E43-1203007-G68 1
GX630(MS-1652)Disassemble SOP
■ 5、HDD Module ASSY
5-1:Remove 2pcs M2.5*5mm Screws Then Remove HDD Door Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 2
2 HDD DOOR ASSY 307-651K411-Y31 1
GX630(MS-1652)Disassemble SOP
5-2:Remove HDD Module as below;
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 1
GX630(MS-1652)Disassemble SOP
5-3:Remove 2pcs M3*3.5mm Screws Then Remove HDD Bracket as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1303501-G68 2
2 HDD Bracket E2M-6510311-Y28 1
3 HDD MODULE ASSY S71-2416504-T14 1
GX630(MS-1652)Disassemble SOP
■ 6、ODD Module ASSY
6-1:Remove 1pcs M2.5*5mm Screw Then Remove ODD Module Assy as below; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 1
GX630(MS-1652)Disassemble SOP
6-2:Remove ODD Bezel as below;
NO. Part Name Part No. Qty
1 ODD Bezel E2P-651F211-Y31 1
GX630(MS-1652)Disassemble SOP
6-3:Remove 2pcs M2*3mm Screws Then Remove ODD Bracket as below; Note:Screw driver torque is 1.5~1.8kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 2
2 ODD MODULE S7D-2270001-SI4 1
3 ODD Bracket E2M-6510211-Y28 1
GX630(MS-1652)Disassemble SOP
■ 7、HINGE COVER ASSY
7-1:Push Fastener as below;
GX630(MS-1652)Disassemble SOP 7-2:Remove Hinge Cover as below;
NO. Part Name Part No. Qty
1 HINGE COVER 307-651E221-Y31 1
GX630(MS-1652)Disassemble SOP
7-3:Remove Hinge Cover Cable as below;
NO. Part Name Part No. Qty
1 POWER BOARD 607-1652B-01S 1
GX630(MS-1652)Disassemble SOP
7-4:Remove Cap Sensor Board as below;
GX630(MS-1652)Disassemble SOP
7-5:Remove Cap Sensor Board as below;
NO. Part Name Part No. Qty
1 Cap Sensor Board 607-1652D-01S 1
2 Cap Sensor Board Cable K1C-1012023-J36 1
GX630(MS-1652)Disassemble SOP 7-6:Disconnect Camera Cable out of the slot as below;
NO. Part Name Part No. Qty
1 Camera Cable K10-3006056-H39 1
GX630(MS-1652)Disassemble SOP
7-7:Remove 2pcs M2.5*5mm Screw; Note:Screw driver torque is 2.0~2.5kgf.cm
7-8:Use Plastic Stick Push Hinge Cap as below;
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 2
2 Hinge Cap_L E2P-6513211-Y31 1
3 Hinge Cap_R E2P-6513311-Y31 1
GX630(MS-1652)Disassemble SOP
7-9:Draw Out Camera Cable、Wireless Antenna and 3G Antenna as below;
NO. Part Name Part No. Qty
1 3G Antenna S79-1800780-V03 1
2 Wireless Antenna_L S79-1800800-V03 1
3 Wireless Antenna_R S79-1800790-V03 1
GX630(MS-1652)Disassemble SOP
7-10:Disconnect Coaxia Cable as below;
NO. Part Name Part No. Qty
1 Coaxia Cable K19-3040006-H39 1
GX630(MS-1652)Disassemble SOP
7-11:Remove 4pcs M2.5*7mm Screws; then remove LCD MOUDLE. Note:Screw driver torque is 3.5±0.2kgf.cm(1-2) Note:Screw driver torque is 3.0-3.5kgf.cm(3-4)
NO. Part Name Part No. Qty
1 Screw E43-1257001-H29 4
GX630(MS-1652)Disassemble SOP
■ 8、UPCASE ASSY
8-1:Remove 5pcs M2*3mm Screws, Then Remove Keyboard as below; Note:Screw driver torque is 1.5~2.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 5
2 Keyboard S1N-3UUS112-C54 1
GX630(MS-1652)Disassemble SOP
8-2:Remove 2pcs M2*3mm Screws, Then Remove Power Board as below; Note:Screw driver torque is 1.5~2.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 2
2 Power Board 607-1652B-01S 1
GX630(MS-1652)Disassemble SOP
8-3:Remove 13pcs M2.5*5mm Screws; Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 13
GX630(MS-1652)Disassemble SOP
8-4:Remove PCI-E Card And XD Card as below;
NO. Part Name Part No. Qty
1 PCI-E Card E2P-6510411-Y31 1
2 XD Card E2M-6510111-A81 1
GX630(MS-1652)Disassemble SOP
8-5:Disconnect Speaker Cable and Microphone Cable as below;
NO. Part Name Part No. Qty
1 Speaker S33-A020200-F33 1
2 Microphone S34-2100580-F33 1
GX630(MS-1652)Disassemble SOP
8-6:Remove FFC Cable(TO Power Board) and FFC Cable(TO T/P) as below;
NO. Part Name Part No. Qty
1 FFC Cable(Power Board) K1C-1018003-J36 1
2 FFC Cable(T/P) K1C-1012024-J36 1
GX630(MS-1652)Disassemble SOP
8-7:Remove 2pcs M2*3mm Screws, Then Remover FFC Cable(TO M/B)&(TO Button) as below; Note:Screw driver torque is 1.5~2.0kgf.cm
8-8:Remove Touchpad Bracket;
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 2
2 FFC Cable(TO Button) K1C-1012025-J36 1
3 Touchpad Bracket E2M-5222911-G40 1
GX630(MS-1652)Disassemble SOP
8-9:Remove 1pcs M2*3mm Screw, Then Remove Touchpad Button Board; Note:Screw driver torque is 1.0~1.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 1
2 Touchpad Button Board 607-1651C-C10 1
GX630(MS-1652)Disassemble SOP
8-10:Remove FFC Cable (TO Button) as below, then remove touchpad module;
NO. Part Name Part No. Qty
1 FFC Cable(TO Button) K1C-1012025-J36 1
2 Touchpad Module S78-3700360-SD2 1
GX630(MS-1652)Disassemble SOP
8-11:Remove 4pcs M2*3mm screws, then remove speaker module s below; Note:Screw driver torque is 1.0~1.5kgf.cm
8-12:Remove 2pcs s below;
NO. Part Name Part No. Qty
1 screw E43-1203007-G68 4
2 speaker S33-A020200-F33 1
3 magnet E2Y-6512511-SF7 2
GX630(MS-1652)Disassemble SOP
■ 9、LOWER CASE ASSY
9-1:Remove 1pcs M2.5*5mm Screw, Then Remove FFC Cable (TO Audio Board) as below; Note:Screw driver torque is 2.3±0.2kgf.cm
9-2:Remove FFC Cable (TO Power Board) as below;
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 1
2 FFC Cable(To Audio Board) K1C-1020003-J36 1
3 FFC Cable(To Power Board) K1C-1018003-J36 1
GX630(MS-1652)Disassemble SOP
9-3:Remove RJ11 Cable and Bluetooth Cable as below;
9-4:Remove M/B;
NO. Part Name Part No. Qty
1 RJ11 CABLE K10-3002114-H58 1
2 BLUETOOTH CABLE K10-3008077-H39 1
3 M/B 607-16521-01S 1
GX630(MS-1652)Disassemble SOP
9-5:Remove 1pcs M2*3mm Screw, Then Remove Bluetooth Antenna; Note:Screw driver torque is 1.0~1.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 1
2 BLUETOOTH ANTENNA S79-1800890-V03 1
3 BLUETOOTH MODULE 605-6837D-070 1
GX630(MS-1652)Disassemble SOP
9-6:Remove 2pcs M2*3mm Screws, Then Remove Audio Board; Note:Screw driver torque is 1.0~1.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 2
2 AUDIO BOARD 607-1652A-01S 1
3 LOWER CASE ASSY 307-651D411-Y31 1
GX630(MS-1652)Disassemble SOP
9-7:Remove Bluetooth Antenna、RJ11 Cable and TV IO Jack;
NO. Part Name Part No. Qty
1 BLUETOOTH ANTENNA S79-1800890-V03 1
2 RJ11 CABLE K10-3002114-H58 1
3 TV IO JACK K19-3001017-H39 1
GX630(MS-1652)Disassemble SOP
■ 10、LCD MODULE ASSY 10-1:Remove 8pcs LCD Rubbers Then Remove 8pcs M2.5*5mm Screws;
Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 LCD Rubber E2Y-6510121-Y40 6
2 Screw E43-1255001-G68 6
GX630(MS-1652)Disassemble SOP
10-2:Remove LCD Bezel as below;
NO. Part Name Part No. Qty
1 LCD BEZEL 307-651B211-Y31 1
GX630(MS-1652)Disassemble SOP 10-3:Remove 8pcs M2.5*5mm Screws, Then Remove Left And Right Hinge;
Note:Screw driver torque is 2.0~2.5kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1255001-G68 8
2 Hinge_Left E2M-6510411-G60 1
3 Hinge_Right E2M-6510711-G60 1
GX630(MS-1652)Disassemble SOP
10-4:Remove Inverter Cable, Then Remove Display Module;
10-5:Remove 2pcs MAGNET as below;
NO. Part Name Part No. Qty
1 MAGNET E2Y-3110411-SF7 2
GX630(MS-1652)Disassemble SOP
10-6:Remove Inverter Module、3G Antenna、WLAN Antenna;
NO. Part Name Part No. Qty
1 INVERTER S78-3300450-SG3 1
2 Wireless Antenna_R S79-1800790-V03 1
3 Wireless Antenna_L S79-1800800-V03 1
4 3G Antenna S79-1800780-V03 1
GX630(MS-1652)Disassemble SOP
10-7:Remove CMOS Camera Module as below;
NO. Part Name Part No. Qty
1 CMOS Camera Module S1F-0003040-C54 1
2 Camera Cable K10-3006056-H39 1
3 LCD Cover Assy 307-651A511-CG0 1
GX630(MS-1652)Disassemble SOP
10-8:Remove Coaxial Cable as below;
NO. Part Name Part No. Qty
1 Coaxial Cable K19-3040006-H39 1
2 Display Module S1J-640G017-S02 1
GX630(MS-1652)Disassemble SOP
10-9:Remove 8pcs M2*3mm Screws, Then Remove LCD Bracket as below; Note:Screw driver torque is 1.5~2.0kgf.cm
NO. Part Name Part No. Qty
1 Screw E43-1203007-G68 8
2 LCD Bracket_Left E2M-6510511-Y28 1
3 LCD Bracket_Right E2M-6510611-Y28 1
GX630 (MS-1652)screws specification
Photo Screw specification Label
(M2.5*L5MM) black
(M2*L3MM)white
(M3*L3.5MM) white
(M2.5*L7MM) black
GX630 (MS-1652)screws specification ■ 1、BOTTOM DOOR ASSY total 20pcs screws, ■ specification:
Photo Screw specification
label
(M2.5*L7MM) black
(M2.5*L5MM) black
GX630 (MS-1652)screws specification ■ 2、THERMAL-KIT total 9pcs screws
7
8
5
6
1
2
9
4
3
Photo Screw specification label
(M2.5*L5MM) black
GX630 (MS-1652)screws specification ■ 3、TUNER, WIRELESS ,MDC CARD and HDD ASSY total 8Pcs screws, ■ specification:
Photo Screw specification label
(M3*L3.5MM) white
(M2.5*L5MM) black
(M2*L3MM)white
GX630 (MS-1652)screws specification ■ 4.UPCASE ASSY total 13pcs screws , ■ specification:
Photo Screw specification Label
(M2*L3MM)white
(M2.5*L5M) black
GX630 (MS-1652)screws specification ■ 5.LCD Bezel total 6pcs screws, ■ specification:
Photo Screw specification label
(M2.5*L5MM) black
GX630 (MS-1652)screws specification ■ 6. LCD MODULE ASSY total 16pcs screws
■ specification:
Photo Screw specification label
(M2.5*L5MM) black
(M2*L3MM)white
GX630 (MS-1652)screws specification ■ 7. UPCASE and LOWER CASES total 3cs screws,
■ specification:
Photo Screw specification label
(M2*L3MM)white
GX630 (MS-1652)screws specification ■ 8、NB total 1pcs screw,
■ specification:
Photo Screw specification label
(M2.5*L5MM) black
GX630 (MS-1652)screws specification ■ 9. Bluetooth and Audio Board 3pcs screws
■ specification:
Photo Screw specification label
(M2*L3MM)white
GX630 (MS-1652)screws specification ■ 10. Touch Pad Board total 3pcs screws ■ specification:
Photo Screw specification label
(M2*L3MM)white