Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
CERTIFI CATE NUMB ER
15-BK1382920-PDA
ABS TECH NICAL OFFICE
DATE
06 Jul 2015
Susan Eng ineering Services
CERTIFICATE OF
DESIGN AsSESSMENTThis is to certify that a representative of this Bureau did, at the request of
DK LOK CORPORATIONassess design plans and data for the below listed product. This assessment is a representation by the Bureau as to the
degree of compliance the design exhibits with applicable sections of the Rules. This assessment does not waive unit
certification or classification procedures required by ABS Rules for products to be installed in ABS classed vessels or
facilities. This certificate, by itself, does not reflect that the product is Type Approved. The scope and limitations of
this assessment are detailed on the pages attached to this certificate.
Product:
Model:
Valve
V81, V82 , V83 , V86 , VH86, V23, V15 , V16 , V46, V56, V96, V103 , V33, VP33,
VA33,VH36,VL36,V73,V76,V63,V66,VB16
This Product Design Assessment (PDA) Certificate 15·B KI382920-PDA. dated 06/JuU201 5 remains valid until 05/Ju1l2020 or until the Rules or
specifications used in the assessment are revised (whichever occurs first).
This PDA is intended for a product to be installed on an AS S classed vessel, MODU or facility which is in existence or under contract for
construction on the date of the ASS Rules or specifications used to evaluate the Product.
Use of the Product on an AS S classed vessel, MODU or facility which is contracted after the validity date of the ASS Rules and specifications
used to evaluate the Product, will require re-evaluation of the PDA.
Use of the Product for non ASS classed vessels, MODUs or facilities is to be to an agreement between the manufactu rer and intended client.
AMERICAN BUREAU OF SH IPPING
H'(!lh- Du-: kHyun-Dae Lee
Engineer
'll11 II", ..-,,,Il,.,I<'," "k",," ",rnrh~ ",,' "lIh " '''" ,,, "",''' ,,1Ih,- Ruk,_l,u,J." -1.,,,.1,,,.1, ,,, "rI"·,, 11,,'11.' "I .\1\:- ,., .• ""'''''''}, ",.1"'"1.11<>t ,,'"""1 ....1\>'"'' ""uJ.ud, I, " ,,,,,,..1,,'Id} 1", ,1,,- """I .\1\" ,I- ,,'''''''U I...... ",' It,."" '" ''1h.., ~uth.,rt~ed ,'nlltre, .In} "l:",h,.lln, h,,,,~'t·, '" ,hf .,I''''-IlI,",,,,,,,-d p"~ lu,, ""h"", .'pl'",,,,II,,,,,, .\1\" ",II ,,.,,,It '" ,h" ",,,,h,.'''' h...."",I1\~ ",, 11 ,,,,.1"",1lh" ",,,,I,, ,II,' " ~''' '' rr,,"J l>~ ,I,,' lam, .1IlJ"'nd"",,,,~, ""lt~",,"<1 on.-\11" R"k·, 1-1-,-\V~ >l 1""" _""I( ",,,10,,,,,,_ "I ,h.. R,"!""'" 1,·, 1'""J,,, I r~l'" '\1'1',.".,1 ~"d '\l:"''''''''nl \b'1I1'
A81S 8(0 110)
DK LOK CORPORATION
7 GOLDEN ROOT-RO
129 BEON-G IL
JUCHON-MYEON
GlMHAE
Korea, Republic of
Telephone: 82-70-47 07-83 72
Fax: 82-7 0-90 1-0 145
Email : dkqa@dk lok .com
Web: ww w.dklok.com
T ier: 3 - Type App roved, u nit certification not required
Product:
Model:
Va lve
V81 , V82, V83, V86, V1I86, V23, V15, V16 , V46, V56, V96 , VI 03, V33 , VP 33, VA33, VH36,VL36, V73 , V76 , V63, V66, VB 16
Intended Service:Saturated Steam , Compressed air , Hydrau lic oil, Lubricating oil, Fuel oil, Fresh water, Sea water
Descripti on:I. V8 11) Nominal Diameter : As per the attache d manufacturer 's document2) Bod y : Stainless Steel/B rass
2. V82I ) Nominal Diameter : As per the attached manufacturer' s document2) Bod y : Stain less SteellBrass
3. V83I) Nomina l Diam eter : As per the attached manufacturer ' s document2) Body: Stain less Stee l/Carbon Steel
4. V86I) Nominal Diameter : As per the attached manufacturer ' s document2) Bod y : Stainless Steel
5. VH86I) Nominal Diameter : As per the atta ched manufacturer ' s document2) Body : Stainless Steel
6. V23I) Nominal Diam eter : As per the attac hed manufa cturer's document2 ) Body : Sta inless Stee l/Brass
7. VIS1) Nominal Diameter : As per the attached manufacturer' s document2) Body: Sta inless Steel/Brass/A lloy 400
8. V I6I) Nominal Diameter : As per the attac hed manufacturer ' s document2) Body : Stainless Steel/A lloy2 0/A lloy C276
9. V461) Nominal Diameter : As per the attached manufacturer ' s document2) Body : Stainless Stee l/Carbon Steel
10. V561) Nominal Diameter : As per the attached manufacturer 's document2) Bod y : Stainless Stee l/Carbon Steel
II. V96
As of 06/Jul/20 15 Type Approved Page 1 of 6
DK LOK CORPORATION7 GOLDEN ROOT-RO
129 BEON-GIL
JUC HON-MYEON
GIMHAE
Korea, Repub lic of
Tele phone: 82-70 -4707-8372
Fax: 82-70-9 01-0 145
Email: dkqa@dklo k.com
Web: www. dklok.com
Tier: 3 - Type Approved, unit certification not required
1) Nominal Diameter: As per the attached manufacturer's document2) Body : Stainless Steel
12. VI03I) Nominal Diameter: As per the attached manufacturer's document2) Body : Stainless Steel/Brass
13. V331) Nominal Diameter : As per the attached manufacturer's document2) Body : Sta inless Steel/Brass
14. VP33I) Nominal Diameter : As per the attached manufacturer's document2) Body : Sta inless SteellBrass
15.VA331) Nominal Diameter : As per the attached manufacturer's document2) Body: Stainless SteellBrass
16. VH361) Nominal Diameter : As per the attached manufacturer's document2) Body : Stainless Stee l
17. VL36I) Nominal Diameter : As per the attached manufacturer 's document2) Body: Stainless Stee l
18 V731) Nominal Diameter : As per the attached manufacturer's document2) Body : Stainless Steel/Brass
19. V76I) Nominal Diameter : As per the attached manufacturer's document2) Body: Stainless Steel/Brass
20. V63I) Nominal Diameter : As per the attached manufacturer's document2) Body: Stainless Steel
21. V66I) Nominal Diameter: As per the attached manufacturer's document2) Body : Stainless Stee l
22.VB161) Nominal Diameter : As per the attached manufacturer's document2) Body : Stainless Steel
Rating:I. Model: V81a. Design Pressure: 68.9bar @38 deg.C
As of 1I6/.JuI1201S Type Approved Page 2 of 6
DK LOK CO RPO RATI ON
7 GOLDEN ROOT-RO
129 BEON-GI L
JUCHON-MYEON
GIMHAE
Korea, Republic of
Telephone: 82-70-4707-8372Fax: 82-70-90 1-0145
Email: [email protected]: www .dklok.com
T ier: 3 - Type Approved, unit certification not required
b. Design Temperature: - 18 - 204 deg.C
2. Model: V82a. Design Pressure : I72bar @38 deg.Cb. Design Temperature: 10 - 65 deg.C
3. Model : V83a. Design Pressure : 151bar @38 deg.Cb. Design Temperature : -18 - 232 deg .C
4. Model : V86a. Design Pressure : 4 13bar @38 deg.Cb. Design Temperature : -18 - 130 deg.C
5. Model : VH86a. Design Pressure: 413ba r @38 deg.Cb. Design Temperature : -18 - 180 deg.C
6. Model : V23a. Design Pressure: 206ba r @38 deg.Cb. Design Tempe rature: - 18 - 204 deg.C
7. Model: VISa. Design Pressure : 345bar @38 deg.Cb. Design Temperature: - 18 - 232 deg.C
8. Model : V I6a. Design Pressure : 4 13bar @38 deg.Cb. Design Temperature : -18 - 232 deg.C
9. Model : V46a. Design Pressure : 4 13bar @38 deg.Cb. Design Temperature: -18 - 232 deg.C
10. Model : V56a. Design Pressure : 413bar @38 deg.Cb. Design Tempera ture: -18 - 232 deg.C
I I. Mode l : V96a. Design Pressure : 413bar @38 deg.Cb. Design Temperature: - 18 - 121 deg.C
12. Mode l : V I03a. Design Pressure : 20.6bar @38 deg.Cb. Design Temperature : -18 - 93 deg.C
13. Model : V33a. Design Pressure : 206bar @21 deg.Cb. Design Temperature : - 18 - 190 deg.C
14. Model : VP33
As of06/Jul/2015 Type Approved Page 3 of 6
DK LOK CO RPO RATI ON
7 GO LDEN ROO T-RO
129 BEON-G IL
JUC HON -MYEON
G1MHAE
Korea, Republic of
Telephone: 82-70-47 07-8372
Fax : 82-70-901-0 145
Ema il: [email protected]
Web: www.dklok.c om
Tier: 3 - Type Approved, unit certification not requ ired
a. Design Pressure: 206bar @2 1 deg.Cb. Design Temperature : -18 - 190 deg.C
15. Mo de l : VA33a. Design Pressure : 206bar @2 1 deg.Cb. Design Temperature : - 18 - 190 deg .C
16. Model : VH36a. Design Pressure : 413 bar @2 1 deg.Cb. Design Te mperatu re : -18 - 190 deg .C
17. Model : VL36a. Design Pressure : 41 J bar @38 dcg.Cb. Design Temperature: - 18 - 48 2 deg .C
18. Model : V73a. Design Pressure ; 206bar @38 deg.Cb. Design Temperature : -18 - 482 deg.C
19. Mo del: V76a. Design Pressure : 4 13bar @38 deg.Cb. Design Temperature : -18 - 482 deg.C
20. Model : V63a. Design Pressure : 20.6bar @20 deg.Cb. Design Tempera ture : -12 - 135 deg.C
21. Model: V66a. Design Press ure: 4 13bar @20 deg.Cb. Design Temperature : -12 - 135 deg.C
22 . Model: VB I6a. Design Pressure : 4 13bar @38 deg.Cb. Design Te mperature : -18 - 232 deg.C
Service Restriction:Un it Certi ficat ion is not required for thi s produ ct. If the man ufacturer or purc haser requests an ABS Certificate forcompliance with a specificat ion or standard, the spec ification or standard, inc ludi ng inspection standards andtole rances . must be clearly defi ned .
Com ments:I . The Manufacture r has provided a declarati on about the control of, or the lack of Asbest os in this product.2. The materi als for body, disc stem and scat arc to be suitable for intended service.3. Maxim um service pressure and temperature are not to exceed those specified by the manufactu rer.4 . All va lves intended for installation on the side she ll, includin g va lves at the sea ches ts, are to be hydro stat icall ytested, before installation, to a pressure of at least 5 bar, in the presence of the Surveyor.
Notes/Dr awing/Documenta t ion:Thi s Product Design Assessment (PDA) is based on as follo ws:- Drawing No. V8 1 Ser ies, Rev.O, Ball va lve
As of 06/Jul/2015 Type Approved Page 4 of 6
I>K LOK CO R PO RATIO:"
7 GOLDEN ROOT-RO
129 BEON-GIL
JUCHON-MY EON
GIMHAE
Korea, Republic of
Te lephone: 82-70-4707- 8372
Fax : 82-70 -901-0 145
Ema il: dkqa @d klok .eom
Web : www.dklok.corn
Tier: 3 - Type Approved, unit certification nn t required
- Drawin g No. V82 Series, Rev.O, Ball valve- Drawing No. V83, Rev.O, Ball valve- Drawi ng No. V86, Rev.O, Ball valve- Drawin g No. V1l86, Rev.O, Ball valve- Drawing No. V23, Rev.O, Plug valve- Drawing No. V15, Rev.O, Needle Valve- Drawing No. V I6, Rev.O, Union bonnet valve- Drawing No. V46 , Rev.O, Gauge root valve- Drawing 1'\0. V56, Rcv.O, Instrument manifolds valve- Drawin g :-':0. V96. Rcv.O, Rising stem plug valve- Drawing :\0. V10 3, Rcv.O, Toggle valve- Drawing :\0. V33, Rev.O, Check Valve- Drawing No. VP33, Rev.O, Check Valve- Drawing No. VA33, Rev.O, Adj ustab le check valve- Dra wing No. VH36, Rev.O, Chec k Valve- Drawing No. VL36, Rev .O, Lift check Valve- Drawing No. V73 , Rev.O, In-L ine Filters- Dra wing No. V76, Rev.O, Tee Filters- Drawin g No. V63, Rev.O, Relief Valve- Drawing No. V66 , Rev.O, Relief Valve- Drawin g No. VB I6, Rev.O, Integral Bonnet Needle valve- Burst test report (BK I 73845 I ) witnessed by ABS Su rveyor dated 9 Octobe r 2009.- Burst test report (B K29 I 7 I 73) wi tnessed by ABS Surveyo r daled 3 June 20 15.
Terms of Valid itv :Thi s Product Design Assessme nt (PDA) Certificate 15-BK J38 2920 -PDA, da ted 06/Ju1l201 5 remains valid until05/Ju1l2020 or unti l the Rule s or specifications used in the assessment are revised (whichever occur s first).
This PDA is intended for a product to be installed on an ABS classed vessel, MO DU or facility which is in existenceor under contract for construction on the date of the ABS Rules or specifications used to evaluate the Product.
Usc of the Product on an ABS classed vesse l, MODU or facility which is contrac ted after the validity date of the ABSRules and specifications used to evaluate the Product, will require re-evaluation of the PDA.
Usc of the Product for non ABS classed vessels, MO DUs or facilities is to be to an agreement between themanufacturer and intended client.
ST ANDAIW S
ABS Rules:201 5 Steel Vessels Rules 1- 1-417.7, I- I-A3 & A4, 4-6-2/3 .1,4-6-2/5.11,4-6-2/5.15
Nation al:NA
Internatio na l:NA
As of 06/.1 ul/20 15 Type App r oved Page 5 of 6
DK LOK CORPORATION
7 GOLDEN ROOT-RO
129 BEO N-GIL
JUCHO N-MYEO N
GIMHAE
Korea , Republi c of
Telephone: 82-70-4707-8372
Fax: 82-70 -90 1-0145
Email: dkqa @dklok .com
Web: www.dklok.corn
Tier: 3 - Type Approved, unit certification not required
Government:NA
EU M ED:NA
OTHERS:NA
As of 06/,Ju1 /201S Type Approved Page 6 of 6
DK LOK CORPORATION7 GOLDEN ROOT-RO, 129 BEa N-GIL,JUCHON-MYEON, GIMHAE, JUCHON-MYEON,Korea, Republic of,
ATTN: Mr. K. H. Lee,
Reference:Project Number:Date:
HJK4/yhbrrI 38292015729897 July 2015
Review Activity :
Gentlemen:
Product Design Assessment (PDA, Revalidation) for "Valves"
Model: V81, V82, V83, V86, VH8 6, V23, VIS, V16, V46, V56, V96, VI03,V33, VP33, VA33, VH36, VL36, V73, V76, V63, V66, VB16
(Applicable Rules : 2015 Steel Vessel Rules)
Your Ref.: Transmittal dated 4 June 2015
We have received your declaration stating that the material s in the requested assessment are free fromAsbestos and your application for ABS Type Approval dated 07 January 2015 and 04 June 2015 togetherwith the enclosures listed below and are pleased to advise that we have completed the Product DesignAssessment (PDA) phase of the type approval process. Enclosed is your original copy of the PDA. Yourdetails are publi shed on our web site at ww2.eagl e.org and can also be downloaded there.
Please be sure that you understand the scope and conditions of the validity of the certificate. An assessmentis not an approval. As applicable, the PDA is a generic assessment of materials, components, products orsystems for a specific use in compliance with the Rules, Guides and recognized standards. In essence thefinal approval is given when an Engineer or Surveyor accepts it for a specific user and installation.Therefore, the PDAs are written assuming that the end user and installation of the product is unknown, andthat the manufacturer may not apply for Manufacturing Assessment.
In particular we draw your attention to the pages attached to the PDA and the restrictions that may affect itsuse.
Unit Certification is not required for this product. If you or your purchaser requests an ABS Certificate forcompliance with a specification or standard; the specification or standard, including inspection standardsand tolerances, you must clearly define the conformity criteria.
This Product Design Assessment (PDA) is intended for products to be used on ABS classed vessels,MODUs or facilities which are in existence or under contract for construction on the date of the ABS Rulesused to evaluate the Product. The use of the product in a non-AB S classed vessel, MODU or facility is to bemutually agreed between your company and your client
We recommend that you monitor the ABS Rules, Guides and other standards used in the approval. TheseRules, Guides and standards often change on an annual basis, and you must comply with the new Rules,Guides and standards in order for the product to be used on an ABS classed vesse l or facility contractedunder the new Rules, Guides or specifications.
We do caution you that the use of the ABS logo is copyrighted . However, our "Design Assessed" logo maybe used as long as your PDA remains valid.
- Continued to next page -
PACIFIC DIVISION8th Floor, Kyobo Life Insurance Bldg., 7, Chungjang-daero, Jung-gu. Susan, 600-737, Republic of Korea
TEL : +82-5 1-469-8371. FAX: +82-5 1-462-4830 . WEBSIT E: wwweaote.orpPAGE 1 of 3
Our "Product Type Approva l" Logo may be used as long as you have an IS09001 Certified Quality System(or equivalent) and you are conducting regular ABS Manufacturing Assessment audits of yourmanufacturing process. Should you desire to continue with Product Type Approval, please contact the ABSOffice at Busan, Tel: 82-51-463-4600, Fax: 82-51-463-4610. The office will arrange for the productiontesting as may be necessary and audit of your quality assurance and control arrangements. To find anotheroffice, please use the directory of ABS offices on the ABS Web Site at www.eagle.org. You may also askthe ABS Program staff at Tel. (281) 877-6107, Fax (281) 877-6591, or e-mail absta-programs@eagle .om.
A copy of the artwork for the Design Assessed and Type Approved logos may be requested from our emailaddress absta-progams@eagle .org. Please be aware that both logos are not to be used at the same time. Fora copy of the art work and detailed guidance on their use, please contact absta-prol!rams@eal!le.org.
An electronic copy of the drawings, appropriately stamped to indicate our review, is available through theABS Eagle Construct Engineering Manager (02E), Web Portal.
Our invoice to cover the cost of the design assessment phase of the type approval process will be sentseparately.
Ifwe may be offurther assistance, please do not hesitate to contact Ms. Hyun-Jung Kim at 82-51-460-4177(Ist contact) or the undersigned at 82-51-460-4167 (2nd contact). In all communications with ABSregarding this approval please quote the Reference and the date of this letter.
Very truly yours,
K.M. WongSen ior Vice President of EngineeringABS Pacific Division
BV:~Yun-Hak Bae kPrincipa l EngineerShip/Offshore Engineering System Dept.
Encl.: as statedce: ABS Busan - 02E
- Continued to next page -
PACIFIC DIVISION8th Floor, Kyobo Life Insurance Bldg.. 7, Chungjang-daero, Jung-gu, Susan, 600-737, Republic of Korea
TEL: +82-51-469-8371, FAX : +82 -51-462-4830, W EBSITE: www.eaqle .orqPAGE 2 of 3
Enclosures
Drawing No
V8 1 Series, Ball valveV82 Series, Ball valveV83, Ball valveV86, Ball valveVH86 , Ball valveV23, Plug valveV15, Needle ValveV16, Union bonne t valveV46, Gauge root valveV56, Instrument manifolds valveV96, Rising stem plug valveV I03 , Toggle valveV33, Check ValveVP33, Check ValveVA33, Adjustable check valveVH36, Check ValveVL36, Lift check ValveV73, In-Line FiltersV76, Tee FiltersV63, Relief ValveV66, Relief ValveVBI6, Integra l Bonnet Needle valve
BKI738451BK2917I73
Revision No Drawing Title
Rev.O Manufacturer's Valves Specification
Burst test report (dated 9 October 2009)Burst test report (dated 3 June 2015)
PACIFIC DIVISION8th Floor, Kyobo Life Insurance Bldg., 7, Chungjang -daero , Jung-gu, Susan , 600-737, Republic of Korea
TEL: +82-51-469-8371 . FAX: +82-51-462-4830. WEBSITE: www.eagle .orgPAGE 30f3