Embed Size (px)
Citation preview
www.flowcreteaustralia.com.au
DECKSHIELD Car Park Decking Systems for:
9 Exposed Decks 9 Internal Decks 9 Ramps
9 Walkways/Stairwells 9 Demarcation 9 Service Corridors
Deckshield Range Technical Profile
Application Suitability
Product Selector
Multi-storey car parks have always been many customers’ first point of contact with commercial destinations, but it is only recently that developers have made efforts to improve the quality of the car park experience.
Although often underestimated, the correct specification of waterproofing and surfacing materials is critical, within the car park environment, to delivering a long-term, structurally protected and safe facility for car park operators and vehicle owners.
Flowcrete Australia’s Deckshield range offers a number of colourful deck coating solutions geared up to provide slip-resistance, durability and an excellent service life as well as stand-up to common car park problems. What’s more, Flowcrete’s deck coating systems are Singapore Green Label certified.
Each parking facility consists of a range of zones or areas and requires a number of surface applications as a result. Flowcrete offers a wide range of flooring products to meet the surface requirements of the entire car park as well as neighbouring zones.
Exposed Decks Internal Decks Ramps
Instructional Signage Demarcation Kerbs/Islands
Line Marking
Multi-storey Top Deck
RampsMulti-storey
Internal Deck
StairwaysTurning Circles
Stair Landings
Entrance to Shopping Malls
Deckshield ID(1.5mm)
Deckshield UV (WB)
Deckshield Finish
Deckshield Oxide/Quartz
Deckshield Finish
Prepared Substrate
** C
ure
times
at t
empe
ratu
res
betw
een
0–30
˚C c
an b
e ac
hiev
ed b
y al
terin
g th
e qu
antit
y of
cat
alys
t use
d.
For
appl
icat
ions
falli
ng o
utsi
de o
f thi
s te
mpe
ratu
re r
ange
, ple
ase
cont
act y
our
loca
l Flo
wcr
ete
Tech
nica
l Dep
artm
ent.
A low VOC, flexible polyurethane deck coating, system that transforms intermediate decks of multi-storey parking structures.
Typically used to cosmetically enhance, reduce noise, protect and brighten internal car parks.
Technical Profile
FIRE RESISTANCE
EN13501–1 B – s1
SLIP RESISTANCE
Method described inAS4586–2013
Dry & Wet Rating isdependant on specification(in accordance with AS4586–2013)
The slipperiness of flooring materials can change significantly, due to the installation process, after short periods of use, due to inappropriatemaintenance, longer-term wear and/or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) — please contact our Technical Advisors for further details.
TEMPERATURE RESISTANCE
Softens of 70°C Hardens on cooling
WATER PERMEABILITY
Karsten Test Nil (Impermeable)
RESISTANCE TO CHLORIDE IONS
DOT BD47/94: Appendix BMethod B4, 2 (d)
No chloride ion penetration after 28 days
BOND STRENGTH
ASTM D4541 (Pull-Off Test) >1.5MPa*
ABRASION RESISTANCE
Taber Abrader ASTM D4060
0.1mg loss per 1000 cycles 1kg Load using CS17 wheels
CHEMICAL RESISTANCE
Contact Technical Department
VOC CONTENT
ISO11890-2 Very low < 20 g/L
ENVIRONMENTALLY FRIENDLY
Green Label certified — 032–089 EnvironmentallyPreferred Coating
UV LIGHT RESISTANCE
Excellent (Non Yellowing)
SPEED OF CURE** 10˚C 20˚C 30˚C
Light Traffic 30 hrs 18 hrs 12 hrs
Full Traffic 36 hrs 48 hrs 24 hrs
Full Chemical Cure 12 days 7 days 6 days
Attractive: Brightens up dull, dark and musty car parks and suspended floors.
Reduces Noise: Minimises unwanted noise from tyre squeal.
Resistant: Resistance to chemicals, fire and has a low slip potential.
*Assumes concrete compressive strength is greater than 25 N/mm2
032-089 Environmentally Preferred
Coating
Environmentally Friendly: Low in Votaile Organic Compounds (VOCs) and solvent free
Chemical Resistance
Petrol 9
Diesel 9
Antifreeze 9
Hydraulic Fluid 9
Chlorides 9
Battery Acids 9
These figures are typically properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
** C
ure
times
at t
empe
ratu
res
betw
een
0–30
˚C c
an b
e ac
hiev
ed b
y al
terin
g th
e qu
antit
y of
cat
alys
t use
d.
For
appl
icat
ions
falli
ng o
utsi
de o
f thi
s te
mpe
ratu
re r
ange
, ple
ase
cont
act y
our
loca
l Flo
wcr
ete
Tech
nica
l Dep
artm
ent.
A car park deck coating system providing a colourful, watertight surface for intermediate decks of multi-storey structures.
Typically used to cosmetically enhance, reduce noise and brighten internal car parks.
Deckcoat EP Topcoat
Natural Quartz Scatter
DeckcoatEP Primer
Prepared Substrate
Technical Profile
FIRE RESISTANCE
EN 13505–1 B – s1
SLIP RESISTANCE
Method described inAS4586–2013
Dry & Wet Rating isdependant on specification(in accordance with AS4586–2013)
The slipperiness of flooring materials can change significantly, due to the installation process, after short periods of use, due to inappropriatemaintenance, longer-term wear and/or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) — please contact our Technical Advisors for further details.
TEMPERATURE RESISTANCE
Tolerant up to 60°C
WATER PERMEABILTY
Karsten Test Nil (Impermeable)
SURFACE HARDNESS
Koenig Hardness Test 180 secs
BOND STRENGTH
ASTM D4541 (Pull-Off Test) >1.5MPa*
ABRASION RESISTANCE
Taber Abrader BS8204–2 80mg loss per 1000 cycles 1kg Load using CS10 wheelsGrade AR2
CHEMICAL RESISTANCE
Contact Technical Department
ENVIRONMENTALLY FRIENDLY
TGreen Label certified — 032–089 EnvironmentallyPreferred Coating option available.
SPEED OF CURE** 10˚C 20˚C 30˚C
Light Traffic 48 hrs 24 hrs 18 hrs
Full Traffic 72 hrs 48 hrs 36 hrs
Full Chemical Cure 12 days 7 days 6 days
032-089 Environmentally Preferred
Coating
Attractive: Brightens up dull, dark and musty car park environments.
Resistant: Resistance to chemicals, fire and has a low slip potential.
Environmentally Friendly: Low in Volatile Organic Compounds(VOCs) and solvent free.
Chemical Resistance
Petrol 9
Diesel 9
Antifreeze 9
Hydraulic Fluid 9
Chlorides 9
Durable: Hard wearing, durable and abrasion resistant.
Deckcoat EP(0.4–1mm)
*Assumes concrete compressive strength is greater than 25 N/mm2
These figures are typically properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
** C
ure
times
at t
empe
ratu
res
betw
een
0–30
˚C c
an b
e ac
hiev
ed b
y al
terin
g th
e qu
antit
y of
cat
alys
t use
d.
For
appl
icat
ions
falli
ng o
utsi
de o
f thi
s te
mpe
ratu
re r
ange
, ple
ase
cont
act y
our
loca
l Flo
wcr
ete
Tech
nica
l Dep
artm
ent.
Deckshield ED is a low VOC, solvent free, flexible, crack-bridging, waterproof polyurethane car park deck coating.
Typically used to cosmetically enhance and protect external and multi-storey car parks.
Deckshield UV (WB)
Deckshield Oxide0.8–1.2mm ScatterDeckshield
Finish
Deckshield ED Membrane
DeckshieldED Primer
Prepared Substrate
Technical Profile
FIRE RESISTANCE
EN 13501–1 B – s1
SLIP RESISTANCE
Method described in AS4586–2013
Dry & Wet Rating isdependant on specification(in accordance with AS4586–2013)
The slipperiness of flooring materials can change significantly, due to the installation process, after short periods of use, due to inappropriatemaintenance, longer-term wear and/or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) — please contact our Technical Advisors for further details.
TEMPERATURE RESISTANCE
Softens over 70°C Hardens on Cooling
WATER PERMEABILITY
Karsten Nil (Impermeable)
RESISTANCE TO CHLORIDE IONS
DOT BD47/94: Appendix BMethod B4, 2 (d)
No chloride ion penetration after 28 days.
BOND STRENGTH
ASTM D4541 (Pull-Off Test) >1.5MPa*
ABRASION RESISTANCE
Taber Abrader 300mg loss per 1000 cycles 1kg load using CS17 wheels
CRACK-BRIDGING
BS EN 1062–7 Method B1 0.5mm
UV LIGHT RESISTANT
Excellent (Non Yellowing)
SPEED OF CURE** 10˚C 20˚C 30˚C
Light Traffic 30 hrs 18 hrs 12 hrs
Full Traffic 48 hrs 36 hrs 24 hrs
Full Chemical Cure 12 days 7 days 6 days
Crack-Bridging: Conforms to UNE-EN 1062–7:2004Method B — B.3.2
Waterproof: Water resistant and waterproof trafficable deck coating system.
Chemical Resistant: Excellent resistance to engine oil, battery acid, fuel and hydraulic fluid.
UV Light Stable: 100% UV light stable and resistant, non-yellowing
Chemical Resistance
Petrol 9
Diesel 9
Antifreeze 9
Hydraulic Fluid 9
Chlorides 9
Battery Acids 9
Deckshield ED(2.5mm)
*Assumes concrete compressive strength is greater than 25 N/mm2
These figures are typically properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
Deckshield ID Rapide(2.5mm)
Technical Profile
FIRE RESISTANCE
EN 13501–1 C – s1
SLIP RESISTANCE
Method described in AS4586–2013
Dry & Wet Rating isdependant on specification(in accordance with AS4586–2013)
The slipperiness of flooring materials can change significantly, due to the installation process, after short periods of use, due to inappropriatemaintenance, longer-term wear and/or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) — please contact our Technical Advisors for further details.
WATER PERMEABILITY
Karsten Test Nil (Impermeable)
RESISTANCE TO CHLORIDE IONS
DOT BD47/94: Appendix B Method B4,2 (d)
No chloride ion penetration after 28 days
BOND STRENGTH
ASTM D4541 (Pull-Off Test) >1.5 MPa*
ABRASION RESISTANCE
Taber Abrader 300mg loss per 1000 cycles 1kg load using CS17 wheels
CHEMICAL RESISTANT
Contact Technical Department. Resistant to petrol, diesel, antifreeze, hydraulic fluid, chlorides and battery acids.
SPEED OF CURE** PER COAT
Walk on 1 hr
Full Traffic & Chemical Cure 2–3 hrs**
Cur
e tim
es a
t tem
pera
ture
s be
twee
n 0–
30˚C
can
be
achi
eved
by
alte
ring
the
quan
tity
of c
atal
yst u
sed.
Fo
r ap
plic
atio
ns fa
lling
out
side
of t
his
tem
pera
ture
ran
ge, p
leas
e co
ntac
t you
r lo
cal F
low
cret
e Te
chni
cal D
epar
tmen
t.
Deckshield ID Rapide is a flexible MMA car park deck coating system providing a colourful, durable and rapid curing finish.
Typically used to enhance and protect multi-storey car parks and suspended floors.
Rapid Curing: Fast track application, dramatically reducing program time.
Noise Reduction: Higher textured finishes reduce tyre squeal.
Colourful: Aesthetically attractive to brighten dark, dull car parks.
Resistant: Provides fire, slip, abrasion and chemical resistance
Deckshield Rapide Topcoat
Deckshield Oxide / Quartz
Deckshield Rapide/Flowfast
Bodycoat
Silica Quartz Scatter
Deckshield Rapide / Flowfast Damp Primer
Prepared Substrate
Chemical Resistance
Petrol 9
Diesel 9
Antifreeze 9
Hydraulic Fluid 9
Chlorides 9
Battery Acids 9
*Assumes concrete compressive strength is greater than 25 N/mm2
These figures are typically properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
Deckshield ED Rapide(4mm)
** C
ure
times
at t
empe
ratu
res
betw
een
0–30
˚C c
an b
e ac
hiev
ed b
y al
terin
g th
e qu
antit
y of
cat
alys
t use
d.
For
appl
icat
ions
falli
ng o
utsi
de o
f thi
s te
mpe
ratu
re r
ange
, ple
ase
cont
act y
our
loca
l Flo
wcr
ete
Tech
nica
l Dep
artm
ent.
Deckshield ED Rapide is a flexible MMA car park deck coating providing a colourful, watertight, durable surface for exposed decks.
Typically used to cosmetically enhance and protect external and multi-storey car parks.
Technical Profile
FIRE RESISTANCE
EN 13501–1 C – s1
SLIP RESISTANCE
Method described in AS4586–2013
Dry & Wet isdependant on specification(in accordance with AS4586–2013)
The slipperiness of flooring materials can change significantly, due to the installation process, after short periods of use, due to inappropriatemaintenance, longer-term wear and/or surface contaminants (wet or dry).
Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) — please contact our Technical Advisors for further details.
WATER PERMEABILITY
Karsten Test Nil (Impermeable)
RESISTANCE TO CHLORIDE IONS
DOT BD47/94: Appendix B Method B4, 2 (d)
No chloride ion penetration after 28 days.
BOND STRENGTH
ASTM D4541 (Pull-Off Test) >1.5MPa*
ABRASION RESISTANCE
Taber Abrader 300mg loss per 1000 cycles 1kg load using CS17 wheels
CRACK-BRIDGING
BS EN 1062–7 Method A Table 6
Class A3 (-20°C)
CHEMICAL RESISTANT
Contact Technical Department. Resistant to petrol, diesel, antifreeze, hydraulic fluid, chlorides and battery acids.
SPEED OF CURE** PER COAT
Walk On 1 hr
Full Traffic & Chemical Cure 2–3 hrs
Rapid Curing: Fast track application, dramatically reducing program time.
Noise Reduction: Higher textured finishes reduce tyre squeal.
Resistant: Provides fire, slip, abrasion and chemical resistance.
Colourful: Aesthetically attractive to brighten dark dull car parks.
Chemical Resistance
Petrol 9
Diesel 9
Antifreeze 9
Hydraulic Fluid 9
Chlorides 9
Battery Acids 9
Deckshield Rapide TopcoatDeckshield
Oxide / QuartzDeckshield Rapide/Flowfast
Bodycoat
Deckshield Rapide
Membrane
Silica Quartz ScatterDeckshield Rapide /
Flowfast Damp PrimerPrepared Substrate
*Assumes concrete compressive strength is greater than 25 N/mm2
These figures are typically properties achieved in laboratory tests at 20°C and at 50% Relative Humidity.
Europe & Middle East
Baltic States +48 883 303 880 [email protected]
Bulgaria +359 898 61 58 31 [email protected]
Denmark +46 435 40 01 10 [email protected]
France +33 1 60 61 74 42 [email protected]
Germany +49 4187 50 29 470 [email protected]
Italy +39 339 4853258 [email protected]
Norway +47 6486 0830 [email protected]
Poland +48 22 879 8907 [email protected]
Romania +40 766 596 991 [email protected]
Russia +7 916 931 35 13 [email protected]
Spain +34 937 07 0872 [email protected]
Sweden +46 435 40 01 10 [email protected]
UAE +971 4 886 4728 [email protected]
UK +44 1270 753 000 [email protected]
Africa
East Africa +254 20 682 1011 [email protected]
South Africa +27 31 461 3411 [email protected]
Americas
Brazil +55 11 3230 1107 [email protected]
Canada +1 604 628-1782 [email protected]
Chile +56 2 2938 1962 [email protected]
Colombia +57 1 381 9254 [email protected]
Mexico +01 800 099 0468 [email protected]
USA +1 936 539 6700 [email protected]
India
India +91 44 4202 9831 [email protected]
Flowcrete
World leader in seamless resin flooring solutions and other specialist coatings.
Asia Pacific
Australia +61 7 3205 7115 [email protected]
Bangladesh +88 02 985 7222 [email protected]
China +86 10 8472 1912 [email protected]
Hong Kong +852 2795 0478 [email protected]
Indonesia +62 21 252 3201 [email protected]
Malaysia +60 3 6277 9575 [email protected]
Pakistan +92 33 731 59272 [email protected]
Philippines +63 2 834 6506 [email protected]
Singapore +65 6848 7166 [email protected]
Taiwan +886 916 954 291 [email protected]
Thailand +66 2539 3424 [email protected]
Vietnam +84 8 6287 0846 [email protected]
www.flowcreteaustralia.com.au
