CTU202 ACTE - Ch 02b - BJ CT Tools Catalog

BJ Coiled Tubing Tools Catalog

F.O.B. BJ Services Tool Production, (see back of title page for contact information)The latest version of this catalog is always available in Lotus NOTES under TIE \ Coiled Tubing Documents database.

January 10, 2002 BJ Coiled Tubing Tools Catalog

January 10, 2002

Orders may be placed through:

Coiled Tubing Tool ProductionBJ Services6620 – 36 Street S.E.Calgary, Alberta, CanadaT2C 2G4FAX: (403) 215-1361Telephone: (403) 531-6750

Contact Name: John Ferguson, P.Eng.Email address: [email protected]

To ensure you have the latest version of this manual, compare the date on this page with the date on theon-line version of this manual. The on-line manual is located in Lotus NOTES on your nearest LotusNOTES server under the TIE folder. The database title is: Coiled Tubing Documents. Alternatively,contact Coiled Tubing Tool Production.

This publication is the property of BJ Services and may not be reproduced or translated, without the priorwritten consent from the BJ Services, Technical Publication Department, Calgary, Alberta, Canada.

F.O.B. BJ Services Tool Production, (see page 2 for contact information)The latest version of this catalog is always available in Lotus NOTES under TIE \ Coiled Tubing Documents database.

BJ Coiled Tubing Tools Catalog January 10, 2002 Page 1

Table of Contents(See Price List Table of Contents Also)

MATERIAL ................................................................................................................................................................ 3

THREADS ................................................................................................................................................................... 3

STANDARD TOOLS.................................................................................................................................................. 5

Surface Tubing Connector ................................................................................................................................... 7Downhole Filter Sub ............................................................................................................................................ 9Surface Filter Screen.......................................................................................................................................... 11Tubing Grapple Connector ................................................................................................................................ 13BDK Dimpleon Connector ................................................................................................................................. 15Tubing Roll-on Connector.................................................................................................................................. 19Sequence Valve................................................................................................................................................... 23Double Dart Check Valve .................................................................................................................................. 25BDK Double Dart Check Valve.......................................................................................................................... 27Double Flapper Check Valve ............................................................................................................................. 29Double Flapper Check Valve with BDK Cartridge............................................................................................ 31Vortex Nozzle ..................................................................................................................................................... 33Cleanout Nozzle ................................................................................................................................................. 35Bakke Release Tool & Fishing Spear................................................................................................................. 37Kick-off Tool....................................................................................................................................................... 39Centralizer.......................................................................................................................................................... 41Dual Circulation Sub ......................................................................................................................................... 43Straight Bar........................................................................................................................................................ 45Rod Clamp.......................................................................................................................................................... 47Snake Grapple Connector .................................................................................................................................. 49Crossover Sub .................................................................................................................................................... 51Precision Displacement Dart ............................................................................................................................. 53Shearable Center Displacement Plug ................................................................................................................ 57Plug Catcher Sub ............................................................................................................................................... 59

SPECIALIZED TOOLS........................................................................................................................................... 61

Roto-Jet .............................................................................................................................................................. 63Roto-Jet - Options .............................................................................................................................................. 65Tornado.............................................................................................................................................................. 67Downhole Phase Separator................................................................................................................................ 69Well-Vac............................................................................................................................................................. 71Concentric Tubing Surface Connector............................................................................................................... 73Lateral Entry Guidance System.......................................................................................................................... 75Straddle Packer .................................................................................................................................................. 77Universal Connect / Disconnect (UCD)............................................................................................................. 79Bakke Motor-head .............................................................................................................................................. 81Parabow ............................................................................................................................................................. 83

WIRELINE TOOLS................................................................................................................................................. 85

Stiff Wireline Connector..................................................................................................................................... 87Snap Latch.......................................................................................................................................................... 89Tension Release Tool ......................................................................................................................................... 91Bakke Flow Release Cable Head ....................................................................................................................... 93Contact Sub ........................................................................................................................................................ 95BJ Wireline Pressure Bulkhead.......................................................................................................................... 97Bakke Wireline Pressure Bulkhead .................................................................................................................... 99


Page ii January 10, 2002 BJ Coiled Tubing Tools Catalog

DRILLING TOOLS................................................................................................................................................ 101

Bottom Hole Assembly ..................................................................................................................................... 103Boss Anchor ..................................................................................................................................................... 105Steering Tool .................................................................................................................................................... 107Orientation Tool............................................................................................................................................... 109Downhole Pressure/Temperature Memory Unit .............................................................................................. 111

WELL CONSTRUCTION EQUIPMENT............................................................................................................ 113

Side Entry Sub .................................................................................................................................................. 115

INDEX...................................................................................................................................................................... 119

(See Price List Index also)



Material

All tools in this catalog are rated for H2S service and are compatible with BJ Services acid inhibitorsunless otherwise noted.

Threads

The standard threads used on tool joints are listed below. These threads have been selected becausethey are easily cut in most areas of the world and do not require a large make-up torque associated withtapered v-form threads.

Other threads can be special ordered.

Tool O.D. (inch) Thread0.75" 5/8" UNF1 0.75" x 16 UNF1.25 1" x 12 UNF1.5 1.125" x 10SA1.687 1.125" x 10SA1.75 1.125" x 10SA1.75 (optional) 7/8" I.D. 1.375 x 10SA2 1.563 x 8SA2.125 1.70" x 10SA2.375 2.08" x 10 SA2.875 2.125" x 8 SA3.125 2.50" x 5 Acme


Page 4 December 17 2001 BJ Coiled Tubing Tools Catalog



Standard Tools





Surface Tubing Connector

The Surface Tubing Connector provides a reliable connection betweenthe coiled tubing and surface equipment inside the reel. It creates a jointwhich is stronger than the coiled tubing itself. The Surface TubingConnector comes with a 2” Fig. 1502 WECO union connection.

It is not recommended that this be used as a general purpose connectorto coiled tubing.

TubingO.D O.D. I.D. Length SAP No. JDE No.

1-1/4" 4.125" 1.030" 6.77" 112331-1/2" 4.00" 1.28" 7.280" 112341 3/4" 4.00" 1.53" 7.280" 234772" 9802Source: BJ Services - Tool Production





Downhole Filter Sub

The Downhole Filter Sub is attached above various downhole tools such as the Roto-Jet and VortexNozzle tools to prevent clogging and wear on the tool.

The standard Downhole Filter Sub is a wire wound filter. For the Roto-Jet tool, a magnetic trap is alsorequired to collect particles that could plug or damage the magnets in the speed governor. The gapsize on these filters is 0.010”.

Other filter subs are available upon request.

Type O.D. LengthWorkingPressure

TensileRating

MicronRating

SAPNo.

JDENo.

Standard 1-3/4" 28.6" 5,000 psi 25,000 lb 254u 22035 850935Magnetic 1-3/4" 28.5" 5,000 psi 25,000 lb 254u 22113Standard 2-1/8" 36.2" 5,000 psi 20,000 lb 254u 22037 76994Magnetic - Short 2-1/8" 24.22" 5,000 psi 20,000 lb 254u 22523Magnetic - Long 2-1/8" 36.2" 5,000 psi 20,000 lb 254u 22525Magnetic 2-7/8" 28.9" 5,000 psi 60,000 lb 254u 22387Replacement Screen 1-3/4" 12783Replacement Screen 2-1/8" 12900Replacement Screen 2-1/8" 12905Replacement Screen 2-7/8" 22277Source: BJ Services - Tool Production





Surface Filter Screen

The Surface Filter Screen is a wire wound design which mounts ina specially designed WECO 1502 crossover and slides into astandard joint of treating iron. The filter connects to the InlineSurface Filter Plug which is inserted into the Surface Treating iron.The surface filter must have a smaller wire gap than the downholefilter to minimize the risk of plugging the downhole filter.

The filter is provided but not the filter housing.



DescriptionGapSize O.D. Length

MicronRating

SAPNo.

JDENo.

Jetting .007" 1.687" 60" 177 u 11105General .028" 1.687" 86" 635 u 11106 73011Short General .028" 1.687" 40" 635 u 25049Cement .110" 1.687" 86" 2500 u 11107Standard Filter Plug for 2" iron 12890Small Filter Plug for 1-3/4" iron 12840Source: BJ Services - Tool Production



Tubing Grapple ConnectorThe Tubing Grapple Connector connects bottom hole assemblies to the coiled tubing witha superior gripping action. The design has been proven in heavy-duty applications suchas drilling, milling and fishing.

The Tubing Grapple Connector has been optimised for torque and tensile loads. Setscrews are not used to carry the torsional loads in this design. The principle of theconnector is that the grapple has fine thread profile on the inside diameter which is forcedinto the tubing wall by a larger pitch thread on the outside diameter. The Tubing GrappleConnector provides a high tensile and torsional strength connection onto the tubing.

In order to attach the grapple to the tubing there is a specific procedure to ensure thatgood, consistent performance is achieved. Grapples must be checked to ensure that theinternal thread profile and slot edges are sharp, sometimes referred to as "wickers", priorto fitting.



TubingSize Part I.D. O.D. Length Thread

Max.WorkingPressure

SAPNo.

JDENo.

1-1/4" Connector 1.0" 2-1/8" 14.75" 1.70-10SA 5,000 psi 94571-1/4" Slip 94541-1/2" Connector 1.0" 2-3/8" 14.75" 1.70-10SA 5,000 psi 94631-1/2" Connector 1.825-8SA 6011691-1/2" Slip 94601-1/2" Service Kit 232111-3/4" Connector 1.13" 2 5/8" 14.75" 2 1/8"-8SA 5,000 psi 22501 765231-3/4" Slip 224951-3/4" Service Kit 23533 765242" Connector 1.13" 3-1/8" 17.25" 2.50-5 Acme 5,000 psi 94732" Connector 2.65-8SA 94752" Slip 94672-3/8" Connector 1.5" 3 3/8" 17.25" 2.65-8SA 5,000 psi 94502-3/8" Slip 94412-3/8" Connector 1.125" 3-3/8" 17.25" 2.50-5 Acme 5,000 psi 94492-7/8" Connector 2.5" 3-3/4" 17.25" 2.65-8SA 5,000 psi 94822-7/8" Slip 94792-7/8" 2.5-5A 9523Source: BJ Services - Tool Production



BDK Dimpleon ConnectorThe BDK Dimple Connector offers a fast, efficient and safe means of connecting the coiled tubingconnector to the tubing.

The BDK Hydraulic Yoke and Jig are essential tools for making up the BDK Dimple Connectors. TheHydraulic Yoke can be operated via a hydraulic hand pump or control panel. The Jig is designed to suitall wall thicknesses of that particular tubing size. Once the connection has been made it has the sametensile and torque capability as the tubing.

This third-party tool is:• Best in class• Bulk purchased for lowest cost• Delivered immediately from Tool Production inventory• Entered into the quality control system upon entry into Tool Production inventory.



Description SAP No. JDE No.1-1/4" Dimpleon Connector 0.095"W x 1.5"OD 271971-1/4" Dimpleon Connector 0.102"W x 1.5"OD 233851-1/4" Dimpleon Connector 0.109"W x 1.5"OD 234211-1/4" Dimpleon Connector 0.118"W x 1.5"OD 233871-1/4" Dimpleon Connector 0.125"W x 1.5"OD 234231-1/4" Dimpleon Connector 0.145"W x 1.7"OD 95431-1/2" Dimpleon Connector 0.095"W x 1.5"OD 286551-1/2" Dimpleon Connector 0.102"W x 1.5"OD 286571-1/2" Dimpleon Connector 0.109"W x 1.5"OD 23197 8547611-1/2" Dimpleon Connector 0.109"W x 1.5"OD 239051-1/2" Dimpleon Connector 0.118"W x 1.5"OD 288251-1/2" Dimpleon Connector 0.125"W x 1.5"OD 227631-1/2" Dimpleon Connector 0.125"W x 1.75" OD 227611-1/2" Dimpleon Connector 0.125"W x 1.5"OD 227671-1/2" Dimpleon Connector 0.125"W x 1.5"OD 227651-1/2" Dimpleon Connector 0.134"W x 1.5"OD 234591-1/2" Dimpleon Connector 0.145"W x 1.5"OD 250911-1/2" Dimpleon Connector 0.156"W x 1.5"OD 286631-1/2" Dimpleon Connector 0.175"W x 1.5"OD 250211-3/4" Dimpleon Connector 0.190"W x 1.125"OD 95311-3/4" Dimpleon Connector 0.109"W x 1.75"OD 272171-3/4" Dimpleon Connector 0.118"W x 1.75"OD 237371-3/4" Dimpleon Connector 0.125"W x 1.75"OD 237951-3/4" Dimpleon Connector 0.134"W x 1.75"OD 286751-3/4" Dimpleon Connector 0.125"W x 2.125"OD 237931-3/4" Dimpleon Connector 0.134"W x 2.125"OD 6003551-3/4" Dimpleon Connector 0.156"W x 1.75"OD 234612" Dimpleon Connector 0.134"W x 2.125"OD 96362" Dimpleon Connector 0.156"W x 2.125"OD 232152" Dimpleon Connector 0.203"W x 1-1/4" CS Hydril 237492-7/8" Dimpleon Connector 0.190"W x 2.875"OD x 2.5-5 95712-7/8" Dimpleon Connector 0.190"W x 2.875"OD x 2.658"SA 229752-7/8" Dimpleon Connector 0.203"W x 2.875"OD 235412-7/8" Dimpleon Connector 0.203"W x 2.875"OD 230551-1/2" Dimpleon Reelable Connector 0.125"W - 0.109"W 227731-1/2" Dimpleon Reelable Connector 0.125"W - 0.125"W 227691-1/2" Dimpleon Reelable Connector 0.125"W - 0.134"W 227711-1/2" Dimpleon Reelable Connector 0.109"W - 0.109"W 253571 3/4" Dimpleon Reelable Connector 0.134"W - 0.134"W 286472" Dimpleon Reelable Connector 0.134"W - 0.134"W 285232" Dimpleon Reelable Connector 0.203"W - 0.203"W 286511-1/4" Dimpleon Jig Bushing 22781



Description SAP No. JDE No.1-1/2" Dimpleon Jig Bushing 23163 8543321-3/4" Dimpleon Jig Bushing 22783 8547572" Dimpleon Jig Bushing 232132-7/8" Dimpleon Jig Bushing 232391-1/4" - 2-3/8" Hydraulic Dimpleon Yoke 23161 8543332-7/8" - 3-1/2" Hydraulic Dimpleon Yoke 23237Hydraulic Hand Pump 23443 854334Thread Chaser 1.70"-10SA Box/Pin 23791 853162Thread Chaser 1-1/8"-10SA Box/Pin 22785 8531631-1/4" Reamer Cutter 0.095"W 272151-1/4" Reamer Cutter 0.102"W 234251-1/4" Reamer Cutter 0.109"W 232031-1/4" Reamer Cutter 0.118"W 234271-1/4" Reamer Cutter 0.125"W 232051-1/4" Reamer Cutter 0.134"W 238691-1/2" Reamer Cutter 0.095"W 286591-1/2" Reamer Cutter 0.102"W 286611-1/2" Reamer Cutter 0.109"W 22779 8543351-1/2" Reamer Cutter 0.125"W 227771-1/2" Reamer Cutter 0.118"W 288271-1/2" Reamer Cutter 0.134"W 227751-1/2" Reamer Cutter 0.145"W 264051-1/2" Reamer Cutter 0.156"W 286651-1/2" Reamer Cutter 0.175"W 250191-3/4" Reamer Cutter 0.109"W 272191-3/4" Reamer Cutter 0.118"W 237391-3/4" Reamer Cutter 0.125"W 23797 8547581 3/4" Reamer Cutter 0.134"W 286491-3/4" Reamer Cutter 0.156"W 234631-3/4" Reamer Cutter 0.190"W 95322" Reamer Cutter 0.156"W 232252" Reamer Cutter 0.203"W 237512-7/8" Reamer Cutter 0.190W 229732-7/8" Reamer Cutter 0.203W 230572-7/8" Reamer Cutter 0.203W - Rough 230612-7/8" Reamer Cutter 0.203W - Stepped 230591-1/4" Bevel Deburr Cutter 234651-1/2" - 2-3/8" Bevel Deburr Cutter 23159 8543362-7/8" - 3-1/2" Bevel Deburr Cutter 230631-1/2" Internal Reamer Tubing Bushing 23469 8543371-3/4" Internal Reamer Tubing Bushing 23471 8547592" Internal Reamer Tubing Bushing 232232-7/8" Internal Reamer Tubing Bushing 232351-1/4" Internal Combination Reamer System 23467



Description SAP No. JDE No.1-1/2" - 2-3/8" Internal Combination Reamer System 23157 8547602-7/8" - 3-1/2" Internal Combination Reamer System 23233Source: BJ Services - Tool Production



Tubing Roll-on Connector

Roll-on connectors attach tools to the bottom of the coiled tubing string. It isimportant to use the correct roll-on fitting for the wall thickness and size of tubing.The appropriate roller wheel must be used to apply the roll-on fitting.

The two styles of roll-on fitting are:(a) with a roll-on connection on one end and a thread connection on the otherend.(b) with a roll-on connection on both ends (used to spool the tubing onto the reelin an emergency)

Pressure rated the same as the rating of the coiled tubing. Tensile and torquerating is 80% of the coiled tubing.

Tubing circularizers are available.

Picture (a)

Picture (b)

DescriptionSAPNo.

JDENo.

3/4" x 0.080" Wall x 5/8" UNF 250671" x 0.087" Wall x 1"-12UNF 238671" x 0.095" Wall x 1-1/8"-10SA 236131" x 0.095" Wall x 1"-12UNF 237231-1/4" x 0.087" Wall x 1"-12UNF 97441-1/4" x 0.095" Wall x 1"-12UNF 235451-1/4" x 0.102" Wall x 1"-12UNF 97451-1/4" x 0.109" Wall x 1"-12UNF 97531-1/4" x 0.116" Wall x 1"-12UNF 250111-1/4" x 0.125" Wall x 1"-12UNF 238731-1/4" x 0.134" Wall x 1"-12UNF 238711-1/4" x 0.087" Wall x 1-1/8"-10SA 97031-1/4" x 0.095" Wall x 1-1/8"-10SA 97201-1/4" x 0.102" Wall x 1-1/8"-10SA 97471-1/4" x 0.109" Wall x 1-1/8"-10SA 97041-1/4" x 0.116" Wall x 1-1/8"-10SA 250731-1/4" x 0.125" Wall x 1-1/8"-10SA 250711-1/4" x 0.134" Wall x 1-1/8"-10SA 239251-1/2" x 0.095" Wall x 1-1/8"-10SA 9701 852152

Specify the tubing size, wall thickness and threadrequirements for the one end.

(a)

(b)



DescriptionSAPNo.

JDENo.

1-1/2" x 0.102" Wall x 1-1/8"-10SA 129461-1/2" x 0.109" Wall x 1-1/8"-10SA 9702 8540221-1/2" x 0.116" Wall x 1-1/8"-10SA 121251-1/2" x 0.125" Wall x 1-1/8"-10SA 97291-1/2" x 0.134" Wall x 1-1/8"-10SA 121261-1/2" x 0.145" Wall x 1-1/8"-10SA 232291-1/2" x 0.156" Wall x 1-1/8"-10SA 232271-1/2" x 0.175" Wall x 1-1/8"-10SA 129431-3/4" x 0.095" Wall x 1-1/8"-10SA TBA1-3/4" x 0.102" Wall x 1-1/8"-10SA TBA1-3/4" x 0.109" Wall x 1-1/8"-10SA 23149 8511141-3/4" x 0.118" Wall x 1-1/8"-10SA 234351-3/4" x 0.125" Wall x 1-1/8"-10SA 231271-3/4" x 0.134" Wall x 1-1/8"-10SA 235251-3/4" x 0.156" Wall x 1-1/8"-10SA 235232" x 0.109" Wall x 1.70"-10SA 129402" x 0.125" Wall x 1.70"-10SA TBA2" x 0.134" Wall x 1.70"-10SA 97542" x 0.156" Wall x 1.70"-10SA 9740 8531512" x 0.175" Wall x 1.70"-10SA 97412" x 0.190" Wall x 1.70"-10SA 128792-3/8" x 0.109" Wall x 2.08"-10SA TBA2-3/8" x 0.134" Wall x 2.08"-10SA 97152-3/8" x 0.156" Wall x 2.08"-10SA 97162-3/8" x 0.175" Wall x 2.08"-10SA TBA2-3/8" x 0.190" Wall x 2.08"-10SA 97212-7/8" x 0.134" Wall x 2-1/8"-8SA TBA

Tubing Roll-on to Roll-on Connector

DescriptionSAPNo.

JDENo.

1" x 0.087" Wall x 0.087" Wall 285311" x 0.087" Wall x 0.095" Wall 285271" x 0.095" Wall x 0.095" Wall 285291-1/4" x 0.087" Wall x 0.087" Wall 97251-1/4" x 0.087" Wall x 0.109" Wall 97261-1/4" x 0.095" Wall x 0.095" Wall 97241-1/4" x 0.102" Wall x 0.102" Wall 285251-1/4" x 0.109" Wall x 0.109" Wall 97271-1/2" x 0.102" Wall x 0.102" Wall 287351-1/2" x 0.087" Wall x 0.087" Wall 271791-1/2" x 0.095" Wall x 0.095" Wall 25217



DescriptionSAPNo.

JDENo.

1-1/2" x 0.095" Wall x 0.109" Wall 97431-1/2" x 0.102" Wall x 0.102" Wall 287351-1/2" x 0.116" Wall x 0.116" Wall 287971-1/2" x 0.125" Wall x 0.125" Wall 287991-1/2" x 0.134" Wall x 0.134" Wall 288011-1/2" x 0.145" Wall x 0.145" Wall 288031-1/2" x 0.156" Wall x 0.156" Wall 288051-3/4" x 0.109" Wall x 0.109" Wall 25077 851151-3/4" x 0.116" Wall x 0.116" Wall 288071-3/4" x 0.125" Wall x 0.125" Wall 288091-3/4" x 0.134" Wall x 0.134" Wall 288111-3/4" x 0.145" Wall x 0.145" Wall 288131-3/4" x 0.156" Wall x 0.156" Wall 288151-3/4" x 0.175" Wall x 0.175" Wall 288171-3/4" x 0.190" Wall x 0.190" Wall 288191-3/4" x 0.204" Wall x 0.204" Wall 288212" x 0.125" Wall x 0.156" Wall 237872" x 2" x 0.156 Wall x 0.156 Wall 97122-3/8" x 0.175" Wall x 0.190" Wall 25225

Tubing Roll-on Connector Crimp Wheel

DescriptionSAPNo.

JDENo.

3/4" Roll-on Pipe Cutter Crimp Wheel 250811" - 2" Crimp Wheel 9735 718461" - 2" Backup Crimp Wheel 97341" - 2" Cutting Tool 226532-3/8" - 3" Crimp Wheel 97132-3/8" - 3" Backup Crimp Wheel 9714Source: BJ Services - Tool Production





Sequence Valve

Sequence valves are often used in cementing and acid spotting operations.

A sequence valve is designed to hold a positive pressure inside the coiled tubing andtoolstring. The purpose is to allow control and placement of fluids in the well by preventingfree fall of the fluids out of the tubing in a well with a low bottom hole pressure which may leadto collapse of the coiled tubing. Free fall of the fluids is likely when the well pressure is belowthat of hydrostatic column of the fluids that will be pumped into the CT string. Alternatively thevalve may be used to allow positive pressure to be applied inside the coiled tubing whilstrunning in hole in a high pressure well that might impose a collapse load on the coiled tubing.

The positive pressure differential is achieved by the valve system acting against a spring. Inthe Hydrostatic Sequence Valve the spring is coiled steel. In the Nitrogen Charged SequenceValve the spring is a pre-charged nitrogen chamber.

These sequence valves contain stored compressive energy and must therefore be handledwith great care by fully trained personnel only.

2-3/8" Hydrostatic Sequence ValveThe Hydrostatic Sequence Valve acts as a pressure controlled check-valve and back-pressure valve. It provides surface control of fluid injected into the well. The valve isdesigned to handle both clean and abrasive fluids such as cement. Two HydrostaticSequence Valves can be stacked for a higher overall pressure rating. There is no need to runa Double Flapper Check Valve in a string which contains the Hydrostatic Sequence Valve.

2" N2 Sequence ValveThe nitrogen chamber spring does not contain a compensating piston, as exists in theHydrostatic Sequence Valve, therefore, the pre-charge pressure provides an absolute springpressure. A correction factor must be applied to compensate for the rise in pressure of thenitrogen chamber gas resulting from rising temperature as the tool is run in the hole. The pre-charge setting is the valve opening pressure. For example, if the N2 chamber pressure is2,000 psi, then 2,000 is the opening pressure.

The nitrogen charged sequence valve has a higher differential operating pressure rating thanthe Hydrostatic Sequence Valve.

Any release or ball operated tool should be run above the sequence valve.

The sequence valve should not be confused with the Sequencing Valve (available from othersuppliers) as their function and purpose is entirely different.



Description

BackPressureSettingRange

WorkingPressure

TensileRating Length

SAPNo.

JDENo.

1-11/16" Abrasive Tool 0 - 2,300 psi 5,000 psi 16,000 lb 56.75" 91141-11/16" Redress Kit 91172" N2 - Abrasive Tool 0 - 6,000 psi 6,000 psi 20,000 lb 34.0" 220712" Redress Kit 252232-1/8" Abrasive Tool 0 - 2,300 psi 5,000 psi 20,000 lb 34.64" 93932-1/8" Redress Kit 252212-3/8" - Abrasive Tool 500 - 3,000 psi 5,000 psi 17,000 lb 34.64" 90012-3/8" Redress Kit 235391-11/16" SQV Assembly ToolKit (for 5 redresses)

9115

2" N2 SQV Assembly Tool Kit 252992-3/8" SQV Assembly Tool Kit 9024Source: BJ Services - Tool Production



Double Dart Check Valve

A Double Dart Check Valve is used on Coiled Tubing tool strings which are required to have aslick, slim O.D. These types of strings are usually used for simple clean-out operations. The O.D.is limited to the size of the coiled tubing being used.

The tool consists of two darts in tandem which allow flow from the coiled tubing to the annulus butare pushed back onto their seats should there be any back flow. This prevents the well fromproducing up the coiled tubing if there is a break in the coiled tubing at surface. Activation ballscannot be pumped beyond the darts.

The Double Dart Check Valve is available in the following diameters.

Description O.D. Length Thread SAP No. JDE No.3/4" Assembly 3/4" ? 5/8" UNF TBA1" Assembly 1" ? 3/4-16UNF TBA1-1/4" Assembly 1-1/4" 7.5" 1"-12UNF 23721 8540761-1/4" Redress Kit 1-1/4" 23921 8540711-1/2" Assembly 1-1/2" 14" 1-1/8"-10SA 22711 8521571-1/2" Redress Kit 1-1/2" 25025 250251-11/16" Assembly 1-11/16" 14" 1-1/8"-10SA 23673 8527381-11/16" Redress Kit 1-11/16" 250252" Assembly 2" 1-56 – 8SA 287432" Redress Kit 2" 28745

Double Dart Check Valve No-Go Bodies

O.D.No-GoSize SAP No. JDE No.

1-1/4" 1-1/2" 111171-1/4" 1-3/4" 250311-1/2" 1-3/4" 225651-11/16" 2" 23433Source: BJ Services - Tool Production





BDK Double Dart Check Valve

The BDK Double Dart Check Valve is available in the following diameters. The valve offers a safetysystem that ensures against reverse flow within the coiled tubing. PEEK darts and spring returns on thedarts are available options.

Description O.D. Length ThreadSAPNo.

JDENo.

Assembly 1-1/4" 10.5" 1"-12UNF 23383Aluminum Redress Kit 1-1/4" 23745Peek Redress Kit 1-1/4" 23747Assembly 1-1/2" 12.6" 1-1/8"-10SA 22759Aluminum Redress Kit 1-1/2" 23663Peek Redress Kit 1-1/2" 23365Assembly 1-11/16" 15" 1-1/8"-10SA TBARedress Kit 1-11/16" TBASource: BJ Services - Tool Production





Double Flapper Check Valve

The Double Flapper Check Valve (DFCV) is run on virtually all non-stiffwireline coiledtubing operations. The Flappers prevent back flow from the well into the coiled tubing.This is required as CT is used in live well operations and if there is a failure in thetubing at surface, the well is prevented from flowing out through the CT by the closureof the check valves.

Two flappers are used to ensure a double barrier. Flappers are held in the closedposition by a light duty coil spring on the hinge so that the valve closes even at lowpressure/flow differentials. The flappers are designed to allow the passage of balls toactivate tools lower in the toolstring. The DFCV is normally placed immediately belowthe coiled tubing connector. Each flapper is part of a cartridge assembly and twocartridges are installed into the body of the tool. The BJS DFCV features a bleed-offport below the flappers so that any trapped pressures below the flapper can bereleased prior to removal of the tools. Another design feature is the retaining nut whichholds the cartridges in place if the tool joint is backed off prior while there is stillpressure below the cartridge.

Prior to running in hole with the CT the DFCV must be pressure tested at both high andlow pressure. Each flapper should be tested independently. The 1-11/16" and 1-3/4"will be available with O-ring style seat as soon as testing is complete.



O.D. I.D. Length Thread WorkingPressure

TensileRating

SAPNo.

JDENo.

Tool 1-11/16" 0.625" 11.125" 1 1/8"-10SA 5,000 psi 25,000 lb 27451Tool 1-3/4" 0.625" 11.125" 1 1/8"-10SA 5,000 psi 25,000 lb 11423 852229Tool 2-1/8" 1.0" 12.0" 1.70"-10SA 5,000 psi 50,000 lb 9330 71981Tool 3-1/8" 1.062" 16" 2.5"-5 Acme 5,000 psi 130,000 lb 22079Redress 1-11/16" 28533Redress 1-3/4" 22103 73545Redress 2-1/8" to

4-3/4"22685 71982

Source: BJ Services - Tool Production



Double Flapper Check Valve with BDK CartridgeThe Double Flapper Check Valve with BDK Cartridge is used on a tool string as a safetyprecaution to prevent fluid flow up the tubing. This can be a critical component in a livewell where an open end at surface would allow the well to flow uncontrolled.

N.B. Specifying this tool with a BDK cartridge will approximately double the cost.




Description O.D. I.D. Length ThreadWorkingPressure

TensileRatings

SAPNo.

JDENo.

1-3/4" 1-3/4" 0.625" 11.125" 1 1/8"-10SA 5,000 psi 25,000 lb 230531-3/4" Redress 0.688" 1 1/8"-10SA 6004472-1/8" 2-1/8" 0.920" 12.25" 1.70"-10SA 5,000 psi 50,000 lb 230512-1/8" Redress 0.920" 1.70"-10SA TBA2-7/8" 2-7/8" 238192-7/8" Redress 1.125" 2 1/8"-8SA 286973-1/8" 3-1/8" 1.13" 14.7" 2.5"-5 Acme 5,000 psi 130,000 lb 230493-1/8" Redress 0.920" 2.5"-5SA 28697

4-3/4" 17-1/2" 5,000 psiSource: BJ Services - Tool Production



Vortex Nozzle

The Vortex Nozzle uses four tangentially offset nozzles and optionally, a downward jet toproduce a high powered vortex of fluid for the removal of muds, gels, waxes, asphaltenes,light scales and filtercake. Jet velocities often exceed 140 m/sec (460 ft/sec). Vortexrotational speeds at 8,000 rpm or more serve to entrain debris adding abrasion to themechanism of cleaning.

An alternative for harder scales is the Roto-Jet on page 63.

O.D.InsertType Thread

WorkingPressure SAP No. JDE No.

1-3/8" 45° 1"-12UNF TBA 104361-3/8" 90° 1"-12UNF TBA 104351-11/16" 45° A 1 1/8"-10SA 5,000 psi 23415 8540251-11/16" 45° B 1 1/8"-10SA 5,000 psi 234171-11/16" 45° C 1 1/8"-10SA 5,000 psi 10494 768921-11/16" 90° A 1 1/8"-10SA 5,000 psi 10496 8540271-11/16" 90° B 1 1/8"-10SA 5,000 psi 236951-11/16" 90° C 1 1/8"-10SA 5,000 psi 236972-1/8" 45° A 1.70"-10SA 5,000 psi 10498 8540262-1/8" 45° B 1.70"-10SA 5,000 psi 22755 765172-1/8" 45° C 1.70"-10SA 5,000 psi 22757 768932-1/8" 90° A 1.70"-10SA 5,000 psi 10499 8540282-1/8" 90° B 1.70"-10SA 5,000 psi 237032-1/8" 90° C 1.70"-10SA 5,000 psi 237052-7/8" 45° A 1.70"-10SA 5,000 psi 237092-7/8" 45° B 1.70"-10SA 5,000 psi 237112-7/8" 45° C 1.70"-10SA 5,000 psi 237132-7/8" 90° A 1.70"-10SA 5,000 psi 237152-7/8" 90° B 1.70"-10SA 5,000 psi 237172-7/8" 90° C 1.70"-10SA 5,000 psi 23719

Vortex Nozzle Mule Shoe Assembly

O.D. Type ThreadWorkingPressure SAP No. JDE No.

1-11/16" 45° A 1 1/8"-10SA 5,000 psi 104951-11/16" 45° B 1 1/8"-10SA 5,000 psi 236911-11/16" 45° C 1 1/8"-10SA 5,000 psi 23693 8531651-11/16" 90° A 1 1/8"-10SA 5,000 psi 10497

Cone Assembly

MuleshoeAssembly



1-11/16" 90° B 1 1/8"-10SA 5,000 psi 236991-11/16" 90° C 1 1/8"-10SA 5,000 psi 237012-1/8" 90° A 1.70"-10SA 5,000 psi 105002-1/8" 90° B 1.70"-10SA 5,000 psi 223192-1/8" 90° C 1.70"-10SA 5,000 psi 23707 853331Source: BJ Services - Tool Production



Cleanout NozzleA variety of nozzles are used to cleanout fill from vertical andhorizontal wells. The fill may include produced sand ordrilling solids. A variety of fluids will be used with theappropriate nozzles depending on particle size, density, welldeviation profile, completion geometry, reservoir pressureand temperature. Fluids through the nozzles will includegelled water, nitrified water, stable foam, orwater/gel/nitrogen slugs.

90o nozzle recommended for cementing.



Description O.D. Threads SAP No. JDE No.Straight Jet Nozzle 1" 3/4"-16 UNF 28623

1-1/4" 1"-12 UNF 10970 8540791-1/2" 1.125"-10SA 22703 8521531-11/16" 1.125"-10SA 109782" 1.125"-10SA TBA2-1/8" 1.70"-10SA 10984 8544242-7/8" 2.125"-8SA TBA

Jet Down Nozzle 3/4" 5/8"- 18UNF 250691" 3/4"-16 UNF 286251-1/4" 1"-12 UNF 10971 8512871-1/2" 1.125"-10SA 22701 8521541-11/16" 1.125"-10SA 22809 8544252" 1.125"-10SA 22805 8544262" 1.568SA 287492" 1.125"-10SA 10986 8544272-1/2" 1-1/8"-10SA 228032-7/8" 2.125"-8SA TBA

Jet Up Nozzle 1-1/4" 1"-12 UNF 10972 8512881-1/2" 1.125"-10SA 22705 8521551-11/16" 1.125"-10SA 10980 8544282" 1.125"-10SA 10982 8544292-1/8" 1.70"-10SA 10988 8544302-7/8" 2.125"-8SA TBA

Tangential Nozzle 1-1/4" 1"-12 UNF 10973(Cementing) 1-1/2" 1.125"-10SA 22707 852156

1-11/16" 1.125"-10SA 228112" 1.125"-10SA 228072-1/8" 1.70"-10SA 10990 8544312-1/2"' 1-1/8"-10SA 228012-7/8" 2.125"-8SA TBA

Blank Nozzle 1" 3/4"-16 UNF 286211-1/4" 1"-12 UNF 236851-1/2" 1.125"-10SA 239111-11/16" 1.125"-10SA 239092" 1.56 – 8SA 287472" 1.125"-10SA 287412-1/8" 1.70"-10SA 10997 8544322-7/8" 2.125"-8SA TBA3-1/8" 2.5"-5A 28753




Bakke Release Tool & Fishing SpearThe Bakke Release Tool is a heavy duty ball operated tool designed to withstand torqueand load applications such as drilling. Large bores help to minimize pressure drops. Torelease, a ball is pumped down the coiled tubing from surface. Once caught in the ballseat, the pressure required to release depends on the number of shear pins installed in theBakke Tool (typically 1000 psi per shear pin). Ball sizes are ½”, ¾” and 1” respectively forthose listed below.

These tools are supplied nitrited for increased durability when ordered through ToolProduction.

Tensile and compressive loads are transmitted by the dogs, not the shear pins.

There should always be a Bakke Fishing Spear available when the Release Tool is run.The Fishing Spear is not illustrated.




Size Description I.D.I.D.Ball Length

WorkingPressure

(psi)

TensileRatings

(lbs) SAP No. JDE No.1-11/16" Tool 273951-3/4" Tool 7/16" 1/2" 13-1/8" 5,000 31,000 12894 735441-3/4" Redress Kit 12897 755781-3/4" Spear Redress Kit 6004491-3/4" Fishing Spear 22787 735462-1/8" Tool 11/16" 3/4" 15.28" 5,000 46,000 12895 719832-1/8" Spear Redress Kit 6004792-1/8" Redress Kit 22743 719842-1/8" Fishing Spear 232172-7/8" Tool 15/16" 1" 21" 5,000 91,000 237812-7/8" Redress Kit 238152-7/8" Fishing Spear 237993-1/8" Tool 15/16" 1" 21.1" 5,000 130,000 128963-1/8" Redress Kit 228153-1/8" Fishing Spear 23071Source: BJ Services - Tool Production



Kick-off ToolThe Kick-off Tool is used where there is a possibility of hanging up on gas lift mandrels orother obstructions. When an obstruction is encountered, the Kick Off Tool rotates whilecompressing and then slides off the obstacle. After a deflection, the tool resets to its originalrunning position and length.



Size Desc. ThreadsLengthOpen

LengthClosed

WorkingPressure

TensileRatings

SAPNo.

JDENo.

1-11/16" Tool 1 1/8"-10SA 44.6" 39.2" 5,000 psi 30,000 lb 235991-11/16" Redress Kit 227451-3/4" Tool 1 1/8"-10SA 45.58" 39.10" 5,000 psi 30,000 lb 25137 765181-3/4" Redress Kit 227452-1/8" (53 mm) Tool 1.70"-10SA 69.59" 57.7" 5,000 psi 45,000 lb 10718 765302-1/8" Redress Kit 12762 127623-1/8" (79.4 mm) Tool 2.5"-5 Acme 60.285" 48.785" 5,000 psi 77,000 lb 107023-1/8" Redress Kit 23069Source: BJ Services - Tool Production



Centralizer

Centralizers ensure centralization of coiled tubing tools within a casing. Thereare two models: (a) Sleeve, pictured at top (also known as non-rotating),pictured at top; and (b) Standard Fluted.

O.D. Type1-3/4", 2-1/8", 3-1/8", or as required Sleeve1-3/4", 2-1/8", 3-1/8", or as required Standard Fluted






Dual Circulation Sub

The Dual Circulation Sub is used to divert flow out to the wellbore above the toolstring.

Flow is diverted in one of two ways.(a) Flow may be diverted by pumping a ball down the coil. When the ball is caught inthe Dual Circulation Sub, flow is blocked and rerouted directly to the wellbore, aftershearing pins and moving the piston downward.(b) Flow may be diverted by increasing pressure in the string until a burst disk isruptured allowing some of the flow out to the wellbore above the tool string. A varietyof burst disks are available for a variety of triggering pressure differentials. BurstDiscs are stocked in 3,000 psi, 3,500 psi, 4,000 psi and 5,000 psi ratings. Burst discsneed to be ordered separately as the tool only comes supplied with a blank disc.

Note: Burst disks are not approved for use in H2S wells. An exception is the 5,800psi burst disk in the Lateral Entry Guidance System, described elsewhere in thiscatalog.



Description O.D.BallSize Length

MinimumI.D.

WorkingPressure

TensileRatings

SAPNo.

JDENo.

Tool 1-11/16" 3/8" 7.73" 0.345" 5,000 psi 25,000 lb 27431Redress 27445Tool 1-3/4" 3/8" 7.73" 0.345" 5,000 psi 25,000 lb 23035 76527Redress 23513Tool 2-1/8" 5/8" 7.73" 0.500" 5,000 psi 60,000 lb 23475 854822

76528Redress 23515Tool 2-7/8" 7/8" 11.0" 0.812" 7,000 psi 91,000 lb 23771Redress 27443Tool 3-1/8" TBA 7.73" TBA TBARedress TBA

Description SAP No. JDE No.Blank Burst Disk 22693 8548263,000 psi Burst Disk 22691 765293,500 psi Burst Disk 23499 8548234,000 psi Burst Disk 23115 8548245,000 psi Burst Disk 22689 854825Source: BJ Services - Tool Production



Straight Bar

The purpose of a Straight Bar is to provide some centralization of downhole toolsbecause coiled tubing retains some residual curvature even after beingstraightened by the injector chains. By giving the coiled tubing a straight section,the Straight Bar, at the bottom of the coiled tubing or bottom hole assembly, it isoften easier to get past potential obstructions such as liner laps or gasliftmandrels.

The outside diameter of the bar should be the same as the coiled tubing tool stringthat is being used. Different threads are available upon request.

The straight bar is attached below the Check Valve and the Coiled Tubing EndConnector. One or two meter long sections of straight bar are often all that isrequired to move past an obstruction. For an alternative, see the 'Kick Off Tool'.

The shearable Straight Bar is designed to be cut by standard Coiled Tubing BOPs.They may be special ordered from Tool Production.

O.D. LengthSAPNo.

JDENo.

1-1/4" 36" 9874 8512901-1/2" 36" 98751-1/2" 48" 98761-3/4" 36" 9863 8540231-3/4" 48" 22751 8540242" 36" 9873Source: BJ Services - Tool Production

Standard Straight Bar





Rod Clamp

The Rod Clamp is used as a temporary non-damaging clamp while handling thetubing. It can be used in the injector while connecting the bottom hole assembly.

The holding force of a single clamp depends upon many factors. In general, it isnot safe to assume more than 2,500 lb. holding force per clamp.

A side-view and top-view of the Rod Clamp is depicted here.

Pipe O.D. Clamp O.D. SAP No. JDE No.1-1/2" 5.00" 22681 8527401-3/4" 5.30" 11161 8527392" 5.41" 111622-3/8" 5.79" 111632-7/8" 6.20" 111653-1/8" 95493-1/2" 6.69" 11164Source: BJ Services - Tool Production

Side view of hinge plates





Snake Grapple Connector

The Snake Grapple Connector is used to stab coiled tubing into the injector head andstuffing box. It is placed on the end of the coiled tubing, shown as the upper-most sleevein the picture.

After the tool is positioned inside the coiled tubing, a portion of the tool housing is rotatedto drive a wedge against a set of wickers which grip the internal surface of the coiledtubing.

The tool contains a socket for a wire rope ferrule. A minimum of ½” cable isrecommended. The wire cable extends from the hole in the bottom of the tool throughthe injector to a winch. The winch pulls the tubing into and through the injector.

After the coiled tubing is successfully stabbed, then the Snake Grapple Connector isremoved.

A shackle-end version is available for out-of-alignment pulls.

O.D. SAP No. JDE No.1-1/4" 22683 226831-1/2" 226131-3/4" 111662" 97892-3/8" 98942-7/8" 10969Source: BJ Services - Tool Production





Crossover Sub

Crossover subs enable you to make connections between twoincompatible threaded components. We select crossover subsfrom our stock or you can design them using our crossover programlocated in Lotus NOTES, Coiled Tubing Discussion database.

If you require additional support, contact Engineering Support at(403) 531-6750.





Precision Displacement Dart

Precision Displacement Darts can be pumped ahead and behind a fluid, including slurries, to preventcontamination of the fluid with the other fluids being pumped. The darts contain a rupture disc that istriggered to burst at a predetermined pressure after the dart reaches a landing point in the bottom holeassembly. Once the disc ruptures a bore of 12 or 16 mm is exposed to allow passage of activation balls,if required.

The use of these darts gives a surface pressure indication of when the fluid has been displaced to theend of the coiled tubing. This prevents such things as cement slurries from being over-displaced and,therefore, becoming contaminated during placement.

The Precision Displacement Dart material is based on a nickel foil welded between stainless steel flangesand with a nose and body encapsulated in polyurethane. They are shaped to provide a seal with thetubing.

The 12mm standard version cement dart has a heavy nose which encourages the dart to keep head-down in wider bore launch systems. A 1.25" nose is available upon special request.

Standard 12mm bore darts fit 098 & 109WT tubing.Use the 13mm cementing dart on 156WT and give a bore through which a 1/2" ball can pass whenrequired. The tail shape centers one dart behind another and enables a ball to be directed into andthrough the hole as it is swept along, even in horizontal sections.

Specify a 120C, 140C or 160C temperature rating.

For more information, see www.benoil.com.

Max BallSize (in)

7/16 7/16 1/2 9/16 11/16 7/8 1

Bore (mm)CT Size (in) Std 12 12 13 16 20 24 271.00 na na 12315 na na na Na1.25 1240 1241 12415 1242 na na na1.50 1250 1251 12515 1252 1253 na na1.75 1260 1261 12615 1262 1263 1264 na2.00 1270 1272 1273 1274 12752.375 1280 1283 1284 12852.875 1290 1294 12953.50 1300 1304 13054.50 1310 1315



1.25 CTU, 098-125 WT; 12mm bore, metal OD 22mm, OD 28mm, 120C

PressureColorCode Part No.

1000psi yellow TBA2000 orange TBA2700 salmon TBA3000 red TBA4000 blue TBA5000 black TBA6000 brown TBA

1.50 CTU, 098-109 WT; 12mm bore, metal OD 22mm, OD 35 mm, 120C



1.50 CTU, 109-156 WT; 12mm bore, metal OD 22mm, OD 32.5 mm, 120C



1.75 CTU, 109-156 WT; 12mm bore, metal OD 22mm, OD 39 mm, 120C





2.00 CTU, 109-156 WT; 12mm bore, metal OD 22mm, OD 45.5 mm, 120C


1000psi Yellow TBA2000 Orange TBA2700 Salmon TBA3000 Red TBA4000 Blue TBA5000 Black TBA6000 Brown TBA

1.25 CTU, 087-098 WT; 16mm bore, with cone tail, OD 28 mm, 120C


1000*psi Yellow TBA2000* Orange TBA2500 Salmon TBA3500 Red TBA4300 Lt. blue TBA6500* Black TBA

1.25 CTU, - WT; 16mm bore, with cone tail, OD - mm, 120C



1.50 CTU, 087-109 WT; 16mm bore, with cone tail, OD 34 mm, 120C



1.50 CTU, 125-156 WT; 16mm bore, with cone tail, OD 32 mm, 120C. * = subject to confirmation.


1000*psi Yellow TBA2000* Orange TBA2500 Salmon TBA3500 Red TBA4300 Lt. blue TBA6500* black TBA





Shearable Center Displacement Plug

The plug is held with a crosswire, whose thickness is given in the list and whichshears at the given pressure. Pigs are designed to nest into each other so that a2500psi pig can follow a 1750psi pig and they will shear in known succession. Thesepigs usually need a catcher for the plug.These have only been made in the wire sizes indicated and for the coil tubing sizesindicated. The list could be extended, but some preliminary work with thicker wiressuggests that it may be difficult to obtain consistent results.

For more information, see www.benoil.com.

1.25" CT For use in 098-125WT tubing72thou wire 2500psi orange TBA64thou wire 1750psi blue TBA

1.50” CT For use in 098-125WT tubing72thou wire 2500psi black TBA64thou wire 1750psi white TBA

For 156WT tubing, use the following. They use a reduced diameter centre to avoid sticking.72thou wire 2500psi yellow TBA64thou wire 1750psi green TBA

1.75" CT For use in 098-156WT tubing72thou wire 2500psi orange TBA64thou wire 1750psi blue TBA





Plug Catcher Sub

The Plug Catcher is run below the tubing end connector. The plug catcher stopsas many as three shearable portions of the plugs but allows a ball to pass aroundthe assembly to operate a release tool fitted with a small ball catcher.

O.D. LengthMaximumBall Size SAP No. JDE No.

1-3/4" 8.0" 3/8" 9156 76519Source: BJ Services - Tool Production





Specialized Tools





Roto-Jet

The Roto-Jet is designed to clean deposits from vertical and horizontalwellbores. Deposits may range in hardness from mineral scales through togels and particulates.

Controlled-rotation, high-velocity and high hydrodynamic liquid jets haveproven to be more effective at cleaning scale encrusted tubing in a singlepass than conventional static jetting nozzles. Controlled rotation is a keyfactor in reducing the dispersion of the jet and inducing cyclic stress in thescale which leads to efficient removal.

The basic tool is the 1-3/4” size. Conversion kits allow for 2-1/8” or 2-7/8”configurations and are available upon request. The 2-1/8” tool differs fromthe 1-3/4” tool only in the strength of the housings, i.e., a larger diameter.Flow handling capacity is the same.

The 2-7/8” tool permits jetting in larger completions where flow rates inexcess of 1-1/2 barrels per minute are required to circulate debris from thewell. Flow rates up to 3-1/2 barrels per minute are possible with the standard2-7/8” tool. For higher flow rates contact Tool Production for a special bypasssub.



O.D. Desc. LengthWorkingPress.

TensilePull @

0 psi

TensilePull @50000

psi

Max.Operating

Temp.SAPNo.

JDENo.

1-3/4" Tool 87.5"(2222.50mm)

5,000 psi 20,000 lbs 0 lbs 400oF(200oC)

22107

1-3/4" Redress Kit 23105 735451-3/4" Nozzles

S90A..S90ES45A..S45E

1-3/4" Roto-Jet Kit* 22109 735432-1/8" Tool 88.6"

(2250.44mm)5,000 psi 25,000 psi 0 lbs 400oF

(200oC)22535

2-1/8" Redress Kit 231032-1/8" Nozzles

R90A..R90ER45A..R45E

2-1/8" Roto-Jet Kit* 225332-7/8" Tool 106"

(2692.40mm)5,000 psi 20,000 lbs 10,000 lbs 400oF

(200oC)22217

2-7/8" Redress Kit 231072-7/8" Nozzles

R901..R903(A-C)R45A..R45C

2-7/8" Roto-Jet Kit* 22379Roto-JetTachometer

9674

* contains a Roto-Jet Tool complete with downhole filter, surface filter, nozzles, hand tools, spare bearinghousings, extra moles and redress parts for 5 complete redresses.




Roto-Jet - Options

Oversize Moles:Listed below are the SAP part numbers for:

2-1/8” O.D. Shroud for 1-3/4” RJT R90-2 Mole Sub-Assembly.2-7/8” O.D. Shroud for 1-3/4” RJT R90-2 Mole Sub-Assembly.3-3/8” O.D. Shroud for 1-3/4” RJT R90-2 Mole Sub-Assembly.3-3/8” O.D. Shroud for 2-1/8” RJT R90-2 Mole Sub-Assembly.

Also available:Low Flow Roto-jet Conversion Kits for 1-3/4 Roto-JetCarbide NozzlesRoto-Jet Dump Subs

Call for details.

Description SAP No. JDE No.Bullnose 45 deg. – 1-3/4" RJT* 23527Bullnose 45 deg. – 2-1/8" RJT 23573Bullnose 45 deg. – 2-7/8" RJT 23679OS** Mole Kit 1-3/4" To 2-1/8" 28611OS Mole Kit 1-3/4" To 2-7/8" 22995OS Mole Kit 1-3/4" To 3-3/8" 22993OS Mole Kit 2-1/8" To 3-3/8" 22991OS Mole Kit 2-1/8" R45 Bulnose 1-3/4" 28785OS Mole Kit 2.52" OD R45 Bullnose 1-3/4" 28787OS Mole Kit 2.52" OD R90 Bullnose 1-3/4" 6004272" S45M 1-3/4" RJT Shroud Centralizer 287712-1/2" S45M 1-3/4" RJT Shroud Centralizer 287732-1/4" S45M 1-3/4" RJT Shroud Centralizer 28755*RJT = Roto-Jet Tool**OS = Oversize


Bullnose 45o

Oversize Mole





Tornado



O.D. Description Length SAP No. JDE No. US$1-3/4" Tool TBA TBASource: BJ Services - Tool Production



Downhole Phase SeparatorThe Downhole Phase Separator is a tool for dividing gaseous and liquid phases in ajetting or milling tool string downhole. As the co-mingled fluid passes through the innergeometry of the tool liquid and gas phases are separated. Gas exits the tool stringabove the jetting tool or motor, while the liquid continues down the tool string to providemaximum hydraulic power.

The Downhole Phase Separator has no moving parts.

V.1 is for light duty.V.2 is for acid service.V.3 is for general service.



1 3/4" & 2 1/8" Tool 2 7/8" ToolTotal Maximum Combined Flow Rate (at BHP & T) 4 bpm 7 bpmMin Total Combined Flow Rate (at BHP & T) 0.5 bpm 0.5 bpmMinimum Gas Fraction (at BHP & T) 5% 5%Maximum Gas Fraction (at BHP & T) 85% 80%Max gas carry-over 2% 2%Maximum Differential pressure 5,000 psi 5,000 psiMaximum Pressure Drop across Tool 100 psi 150 psi

O.D. Description LengthDifferentialPressure

TensileRatings SAP No. JDE No.

1-3/4" Tool V1 35" 5000 psi 25,000 lb 23295 716071-3/4" Redress Kit V1 23453 765251-3/4" Tool V2 35" 5000 psi 25,000 lb 250451-3/4" Redress Kit V2 287891-3/4" Tool V3 TBA2-1/8" Tool V2 35" 5000 psi 40,000 lb 239612-1/8" Tool V3 TBA2-7/8" Tool V2 60" 5,000 psi 50,000 lb 253152-7/8" Tool V3 60" 5,000 psi 50,000 lb 28619Source: BJ Services - Tool Production



Well-VacThe Well-Vac has two important and very different purposes:• Sand-Vac Mode for debris clean-out; and• Well-Vac Mode for producing wellbore fluids

In Sand-Vac mode, the tool cleans vertical and horizontal wellbores of sandand loose debris by fluidizing and entraining the material in the return flowof a concentric coiled tubing (CCT) string. The Well-Vac has been carefullydesigned to prevent cave-in or damage to the hole and filter-cake.

Power fluid is pumped down the internal string and returned up the annulusbetween two coiled tubing strings. The Well-Vac creates a venturi effect atthe face of the tool as the fluid passes through a specially designed jetpump and from the internal string to the annulus.

Tangential jets on the Well-Vac (2-1/2") swirl debris into forward andbackward moving slurries. The forward moving slurry maximizes travelspeed and minimizes the duration of the cleanout operation. The backwardslurry is pulled into suction ports and sent through the annulus betweenstrings, and out of the well.

The Well-Vac (3-3/4") has an external fluted sleeve that is shear pinned tothe interior body. When zinc alloy pins are sheared by over-pull or acidizingthe BHA becomes a flush profile & will be released. The 2-1/2" Well-Vacis equipped with shear rings at the upper end of the tool. Aluminium ringsare used for releasing the tool from inner and outer strings upon an over-pull or acidizing. Brass rings are used in acid work to prevent accidentaltool release.

The 2-1/2" Well-Vac can also be equipped with a DownholePressure/Temperature Memory Unit in the forward nozzle to record BHPand BHT, and another Downhole Pressure/Temperature Memory Unit torecord diffuser pressure. This option requires additional components andincreases the overall length of the tool by approximately 20 inches.

The Well-Vac (3-3/4") runs on 1-1/4", 2-3/8" CCT.The Well-Vac (2-1/2") runs on 1", 2" CCT or 1-1/4", 2-3/8" CCT.

A complete system analysis is required before ordering this tool. ContactTool Production for assistance.



O.D. Description LengthDifferentialPressure

SAPNo.

JDENo.

2-1/2" Tool 93.2" 96532-1/2" Hand Tool Kit2-1/2" Redress Kit3-3/4" Tool 44.58" 5,000 psi 226233-3/4" BullNose SubAssy 22351 755533-3/4" Hand Tool Kit 226473-3/4" Redress Kit 226493-3/4" O-Ring Redress Kit 253053-3/4" Recirculating Kit 22955Source: BJ Services - Tool Production



Concentric Tubing Surface Connector

The Concentric Tubing Surface Connector splits the innercoiled tubing flow from the outer coiled tubing flow. Theconnector is fastened to the hub of the concentric coiledtubing spool. Depending on the application, fluids may bepumped via the Concentric Tubing Surface Connector intothe inner coiled tubing with returns coming back throughthe annulus between the two coiled tubing strings or visaversa. It is used with the Well-Vac tool.

OuterC.T.

InnerC.T. Length Width

SAPNo.

JDENo.

1-1/2" ¾" 95532" 1" 19.5" 12.3" 6003512-3/8" 1 1/4" 19.5" 12.3" 9687Source: BJ Services - Tool Production

* not included





Lateral Entry Guidance System

The Lateral Entry Guidance System (L.E.G.S.) provides a fast and easy method to enterand stimulate all branches in a multiple-completion well. The L.E.G.S. tool locates andsteers coiled tubing into any branch of a multiple completion well using a specialmethodology which circumvents any need for an electrical control or steering system. Allbranches or sidetracks can be serviced in a single operation without returning to the surfacebetween runs.

The Well-Vac can be used with the L.E.G.S. tool.

Description O.D.Length

with filterSAPNo.

JDENo.

LEGS Tool 2-1/8' 16.5 ft 27199Complete LEGS Kit 2-1/8' 16.5 ft 27479Spare Machine Parts Kit 27469Spool Valve Piston Kit 27471Wands, 6" to 36" Kit 27439O-Ring Teflon Backup Kit 27465Slyd Rings, Spiroloks & Msc. Kit 27467Hand Tools Kit 27477Incolloy Upgrades 9528Source: BJ Services - Tool Production





Straddle PackerThe Straddle Packer contains two inflatable packers spaced as required to cover thetreatment interval. The inflation sequence is initiated simply by increasing the pump rate to apre-set value, which closes a latch valve, filling the elements.

Deflation is accomplished by a simple pulling action to open the latch valve, allowing theelement to deflate. The tool is then ready to be moved to the next treatment interval.

The Sequence Valve in the tool string stops U-tubing effects of fluids during placement.Circulation is maintained while running in the hole or pulling out of the hole with continuouscommunication between the top and bottom of the tool string to prevent swabbing whilemoving the tool.

The following specifications incorporate a significant safety factor:

• Packer elements are rated for 20 inflations in 7” casing. The elements are rated to 280o F(137o C).

• Minimum allowable retrieval diameter after inflations is 3.25”.• Maximum differential squeeze pressure in 7” casing (liner) is 2,000 psi.• Maximum flow (squeeze) rate is 2.5 bpm.• Maximum set-down weight = 10,000 lbf.

O.D. Description SAP No. JDE No.3-1/8" Tool 236153.0" Packer Element 10506Source: BJ Services - Tool Production





Universal Connect / Disconnect (UCD) Top Sub

The Universal Connect / Disconnect (UCD) is a quick connector for joining strings withoutrotation. Threading is not involved in the connection so that tension, compression and torqueloads can be transmitted.

The UCD provides a hands-free, remote deployment capability, which is especially crucialwhen used in live well operations. It is used during vertical deepenings, frac jobs andperforating gun deployment.

The two methods of pressuring up the UCD are:a) by using a modified BOP stack and additional isolation barriers in the stack.b) by a hand pump connected to a port on the UCD. The hand pump may only be used

when remote operation is not required.

The connection process is (1) pressure up the UCD, (2) stab the two halves of the UCDtogether (torque keys self-align), and (3) release pressure, to lock the UCD halves together.

The disconnect process is (1) pressure up the UCD, (2) withdraw the two halves of the UCD,and then (3) release pressure.

Two additional configurations of the UCD are:a) conversion to a BOSS (Ball Operated Shear Sub) tool providing an emergency release for

a BHA that may become stuck in the hole. Pumping a 7/8" diameter ball from surfaceshears a pin in the UCD to effect an emergency release.

b) for use with BJ's wet connectors to provide a reliable electrical connection, a flow path forfluids, and a strong mechanical connection.

O.D. Description Length SAP No. JDE No.3 3/8" Tool 22.5" 12145


Bottom Sub





Bakke Motor-head

The Bakke Oil Tools Moto-head assembly contains dual flapper valves, a hydraulicdisconnect and a dual circulating sub.

The flapper cartridges have been tested by Bakke to 10,000 psi at 400 deg. F.

The heavy duty hydraulic disconnect provides heavy-duty rotation lock to withstandvibration and high torque for long milling operations.

Bending of this tool will not affect the shear pin value as is the case with a collet typetool.

The large bore minimizes pressure drop.

O.D. Description SAP No. JDE No.4-3/4" Bakke Motorhead 9639Source: BJ Services - Tool Production





ParabowThe Parabow is run on coiled tubing to the point in the well where a cement plug is to be situated. Afterthe tool is in position a ball is sent downhole to activate a piston, shut-off circulation, and extrude the innerportion of the tool beneath the tool housing. The inner portion then expands creating a seat for a cementplug.

O.D. Desc. Length SAP No. JDE No.2-1/8" Tool 49.68" 65505-1

Refill 65462Source: BJ Services - Tomball, Texas, USA





Wireline Tools





Stiff Wireline Connector

Function Summary:• mechanical connection from the coiled tubing connector to the wireline (logging) tools.• Electrical connection through an electrical pressure bulkhead.• Flow bypass for circulating well.• Back pressure valve.

Circulation is often required during coiled tubing logging or perforating operations so the StiffWireline Connector features circulation ports and a back-pressure valve. The back-pressurevalve is spring loaded and adjustable from 500 to 2,200 psi. This valve allows a positive internalpressure to be held in the coiled tubing and also acts as a back-pressure valve to maintain wellcontrol should there be a loss of pipe integrity at surface.

The tool includes an anchor sub which secures the logging cable and an electrical pressurebulkhead sub where the logging cable is attached to conventional electric line pin connections.

Uphole thread: 1-1/8” – 10SADownhole thread: 1-3/16” – 12 UN left hand thread.

A Tension Release Tool is usually connected below the Stiff Wireline Connector to provide anemergency release mechanism (see page 91).

O.D. DescriptionTensileRating

WorkingPressure

SAPNo.

JDENo.

1-11/16" Single Conductor 20,000 lb 5,000 psi 94231-11/16" Four Conductor 20,000 lb 5,000 psi 94241-11/16" Redress Kit 225931-11/16" Hand Tools & Test Sub(s) 9428

Hand Tools Kit 28517Source: BJ Services - Tool Production





Snap Latch

The Snap Latch tool enables fast rig-up of long logging tools to a wireline string. The SnapLatch does not require rotation of an entire tool string because there is no threadedconnection.

Wireline (logging) tools connected beneath the Snap Latch can be rotated at will. The toolscan be disconnected only by rotating a collet retainer four turns and then pulling up.

The Snap Latch provides a quick mechanical and electrical connection between two parts of atool string. The Snap Latch can be especially useful when tool strings must be deployed asection at a time because of length restrictions imposed by the lubricator.

A Tension Release Tool, described on the next page, is usually run with a Snap Latch foremergency release.

For an alternative to the Snap Latch see the Universal Connect / Disconnect (UCD) on page79.

O.D. Description LengthTensileRatings

DifferentialWorkingPressure

SAPNo.

JDENo.

1-11/16" Banana Plug 10.70" 16,000 lbs 5,000 psi 9133 765201-11/16" Pin Connector 10.70" 16,000 lbs 5,000 psi 91341-11/16" Redress Kit 23735 76521

Hand Tools Kit 28515Source: BJ Services - Tool Production





Tension Release Tool

The Tension Release Tool is usually placed below the Stiff Wireline Connector and abovethe logging or perforating string. An electrical connection runs through the Tension Releasetool. An anti-rotation lug in the Tension Release Tool prevents rotation of the two halves' ofthe tool to prevents breakage of the electrical connection. A 5,000 lb over-pull triggers arelease.

If the logging or perforating tool string becomes trapped in the well, the coiled tubing can beretrieved by pulling on the Tension Release Tool to trigger release. A collet within theTension Release Tool moves against a stack of disc springs until release is achieved.

If the Tension Release Tool is disconnected, a 3/4" External Fishneck is left behind in thehole. The tool can be re-latched later with a fishing string.

The Tension Release Tool is designed to absorb the shock from perforating operations andcan be used in highly deviated wells.

A proper job design takes into account both the tool string weight and frictional drag so thatthe 5,000 lbf. release load is not inadvertently reached.

Uphole thread: 1-3/16” – 12 UN left hand thread;Downhole thread: 1-3/16” – 12 UN right hand thread.Fishneck size: 0.75” O.D.



O.D. Description LengthTensileRatings

TensilePullto

ReleaseWorkingPressure

SAPNo.

JDENo.

1-11/16" Tool 15.82" 15,000 lb 5,000 lb 5,000 psi 94981-11/16" Redress Kit 285211-11/16" Hand Tools Kit* 28519* includes Test Sub(s)Source: BJ Services - Tool Production



Bakke Flow Release Cable Head

The Bakke Flow Release Cable Head is used on CT e-line operations and is designed forheavier duty than the Stiff Wireline Connector and TRT. The tool provides the followingfunctions;

a) Cable Anchorb) Electrical Bulkheadc) Fluid flow and back pressure check valvesd) Two Step toolstring releasee) Load is carried by heavy duty segments

The toolstring is released by pumping at a predetermined rate through the check valves andexhaust orifice to generate a pressure inside the tool which forces a piston against a spring.Once the piston has moved fully the segments are released and the tensile load is allowed tocome onto the shear pins. Final release is achieved by shearing the pins by either pulling onthe tool or continuing to increase the pump rate.

O.D. LengthTensileRatings

WorkingPressure

SAPNo.

JDENo.

1-3/4" TBA TBA TBA TBA TBA2" TBA 53,000 7500 TBA TBA2-1/2" TBA 77,000 7500 TBA TBA3-1/8" TBA TBA TBA TBA TBASource: BJ Services - Tool Production





Contact Sub

Contact Subs are part of the Stiff Wireline Connector. Specify your threadrequirements when ordering. The contact subs are shown in the same orderas they are listed in the chart below.

Specify your thread requirements when ordering.

A 1-11/16 shearable straight bar is available upon request.

Description O.D.TensileRatings

SAPNo.

JDENo.

Teardrop, spring pin 1-7/16" 20,000 lb 9048Swivel, spring pin 1-11/16" 20,000 lb 9049Swivel, banana plug 1-11/16" 20,000 lb 9050Teardrop, banana plug 1-7/16" 20,000 lb 9051Contact Sub, banana plug 1-7/16" 20,000 lb 9052Type 'S'Contact Sub,banana plug

1-11/16" 20,000 lb 9054






BJ Wireline Pressure Bulkhead

The BJ Wireline Pressure Bulkhead uses Kemlon Connectors and a 2” Fig.1502 WECO hammer union to allow electrical wireline to be passed into apressurized coiled tubing reel. The signal is passed from the pressure bulkheadthrough an electrical quick connect to a signal collector at the center of the reel.As many as eight wires can be connected and anchored within the sub. In thisway, connection can be made from downhole and run to the Slip Ring orCollector.

This Bulkhead is suitable for applications up to 10,000 psi.

* Not Included



O.D. Description Length SAP No. JDE No.3-3/4" Tool 17-3/4" 9699 740143-3/4" Redress Kit 239193-3/4" Slip Ring Assembly 22021 74015Source: BJ Services - Tool Production



Bakke Wireline Pressure Bulkhead

The Bakke Wireline Pressure Bulkhead is used inside the Stiff Wireline Reel toanchor the e-line cable, typically either a 7/16" or 3/8" Hepta Cable. The bulkheadallows the cable to exit the reel and prevent fluids from leaking. The differentialpressure rating of this model is 5,000 psi. The bulkhead attaches to the CT via aFig. 1502 Weco Hammer Union.

Features:• Easy to install• No Kemlon pins (simplicity and economical)• Final electrical connections are not in a wetted area• When used with a Trollex Collector this system is Zone II rated• When used with an alternative collector it is considered as "Rig Safe"

This third-party tool is:• Best in class• Bulk purchased for lowest cost• Delivered immediately from Tool Production inventory• Entered into the quality control system upon entry into Tool Production

inventory.

Description SAP No. JDE No.Tool 27379Trollex Collector TBASource: BJ Services - Tool Production





Drilling Tools





Bottom Hole AssemblyThe Drilling Using Coiled Tubing (DUCT) Bottom Hole Assembly (BHA) is comprised of the following indescending order:

• BOSS Anchor Tool• 3-3/8” UCD Tool• Steering Tool• 3-3/8” UCD Tool• Orientation Tool (c/w Popper Check Valve sub.• Drilling Motor• Bent Sub• Drilling Bit

* indicates components which are not supplied.

OrientationOrientation Tool PoppetPoppet CheckCheckValveValve Sub

SteeringSteering ToolUCDUCD BottomSubSub

TubingTubingGrappleGrapple

UCD TopUCD Top SubBOSSBOSS AnchorToolTool

Bit *Positive DisplacementPositive Displacement Motor * BentBent Housing *

UCD TopUCD Top Sub

UCDUCD BottomSubSub





Boss AnchorThe Boss Anchor V3 is a flow through cable anchor to be used at the top of the tool string,designed to withstand both torque and axial loads. It incorporates a Double Flapper CheckValve in the flow passage, as well as a ball catcher for the release mechanism. The cableanchor is a sealed unit down the center of the tool with the flow passage around the innerannulus of the tool assembly. Anchor of the cable is such that it is allowed to "tear away"when the B.O.S.S. is activated.

O.D. Description Length SAP No. JDE No.3 1/8" Boss Anchor V3 32.0" 23503






Steering Tool

The Steering Tool is part of the coiled tubing directional drilling bottom holeassembly. It contains:• an accelerometer triad, tool face angle and inclination.• a magnetometer triad to give real-time azimuth and inclination.• a gamma tool for measuring the natural gamma radiation of the

formations.• temperature sensors• shock sensors• BHA tubing pressure and annulus pressure

O.D. DescriptionLength with

UCD Top Sub SAP No. JDE No.3-1/8" Steering Tool 345.8" 12289Source: BJ Services - Tool Production





Orientation Tool

The Orientation Tool is part of the coiled tubing directional drilling bottomhole assembly. The function of the tool is to change the bottom holeassembly Tool Face angle while drilling. Orienting can be achieved withoutinterrupting the drilling process. The Orientation Tool is an electric overhydraulic system. It is operated at surface with the aid of a computercontrolled power supply.

The Orientation Tool also houses a circulating valve. The circulating valveis a hydraulic device which, when closed, directs all circulating fluids to thedrill motor. When the valve is open the circulating fluids are directed to theannulus allowing for more efficient hole cleaning using a patented process.



O.D. Description

Length withUCD Bottom

SubTorqueOutput Thread

SAPNo.

JDENo.

3-3/8" Orientation Tool 160.0" 1500 ft-lb 2 3/8" APIREG.

22105




Downhole Pressure/Temperature Memory UnitThis robust Downhole Pressure/Temperature Memory Unit operates inenvironments up to 70 MPa in pressure and 150oC in temperature, under highgravitational loading.

The unit has a memory capacity for 500,000 samples and comes with softwareto setup and program the tool. Sampling rates are from 1 second to severalhours.

The small, long-life lithium battery provides many hours of tool operation. Theestimated battery life is calculated by the software. Battery life is dependantupon downhole temperature, sampling rate and battery manufacture. At anextreme, battery life can be more than 100 hours while sampling once persecond and at extreme operating conditions such as 150oC downholetemperature.

Tools which can incorporate use of this tool include: the Roto-Jet, Well-Vac,Lateral Entry Guidance System and in BJ horizontal drilling strings.

An 'Acquisition' software page provides the basic commands for programmingand downloading data from the unit. Under the 'Processing' tab you will findthe commands for manipulating data files. 'Reporting' presents commands forproducing reports and graphs. A 'Utilities' tab provides options for real-timesampling of data from the unit at surface and downloading of the binarymemory image for later analysis.

The following tools can accommodate the unit with a corresponding letter (seeTool column).



ForHousing

O.D.HousingLength Thread

WellborePressure

ToolPressure

SAPNo.

JDENo.

Roto-Jet (1-3/4") 1-3/4" 18.2" 1-1/8-10S.A. TBALateral Entry Guidance 2-1/8" 14.5" 1.7-10S.A.

TBA

Lateral EntryGuidance System 2-1/8" 23.5" 1.7-10S.A

TBA

Roto-Jet (2-7/8") 2-7/8" 15.5" 2-1/8-8S.A. TBA

Drilling 3-1/8" 15.5" 2-1/8-8S.A. TBA

Roto-Jet (3-1/8") 3-1/8" 26" 2.5-5A. TBA




Well Construction Equipment





Side Entry Sub

The Side Entry Sub anchors a parasite injection string onto casing. The casing string islanded and cemented into place. Gas can then be injected into the returning mudcolumn to facilitate further underbalanced drilling of the next hole section.

An aluminum pump-out plug seals the port during run-in and cementing. When drillingresumes the port is opened by pressuring up the parasite string to pump-out the plug. Ifnecessary, acidizing the shear pin will ensure removal of the plug, and opening of theport.

The coil tubing / Side Entry Sub connection can be pressure tested prior to running in thehole.

Due to the need to match the casing grade, this item is special order only.

O.D. Length Thread SAP No. JDE No.7.969" 40" 5 1/2" API 8 Round Long Casing 93569.500" 40" 7" API 8 Round Long Casing 935711.294" 40" 8 5/8" API 8 Round Long Casing 935812.283" 40" 9 5/8" IPSCO-QB2 5 TPI 9359Source: BJ Services - Tool Production





User CommentsManual Name:

Document Date:

Are there sections of this manual you especially like?

Are there topics that you think need more explanation or graphical representation?

Please identify any errors and their location in the manual.

What parts of the manual do you use most?

What additional material would you like added to future a version of this manual?

Other comments?

If you would like to receive an update:

Your name:

Your address:

Please rate this manual: Excellent Acceptable Poor Did not use

BJ ServicesCoiled Tubing Research, Development & EngineeringTechnical Publications6620 – 36 St. S.E.Calgary, Alberta, Canada.T2C 2G4Fax (403) 531-6751





Index

AAnchor – Boss ............................................... 105

Bback-pressure valve ........................................ 23Bakke Flow Release Cable Head.................... 93Bakke Moto-head ............................................ 81Bakke Release Tool & Fishing Spear.............. 37Bakke Wireline Pressure Bulkhead ................. 99Bar - Straight ................................................... 45BDK Dimpleon Connector ............................... 15BDK Double Dart Check Valve........................ 27BJ Wireline Pressure Bulkhead....................... 97Boss Anchor .................................................. 105Bulkhead – Bakke Wireline Pressure .............. 99Bulkhead - BJ Wireline Pressure..................... 97

Ccalcium carbonates.......................................... 63Catcher Sub - Plugs ........................................ 59Cementing Dart ............................................... 53Centralizer ....................................................... 41Check Valve .................................................... 29Check Valve - BDK Double Dart ..................... 27Check Valve - Double Flapper - with BDK

Cartridge...................................................... 31Check Valve Double Dart ................................ 25check-valve...................................................... 23Circulation Sub - Dual...................................... 43Clamp - Rod type............................................. 47Clean out – Well-Vac....................................... 71Cleaning Wellbore – Vortex Nozzle................ 33cleaning wellbore............................................. 63Clean-out - Tornado ........................................ 67Cleanout Nozzle .............................................. 35Comments form ............................................. 117Concentric Tubing Surface Connector ............ 73Connect (UCD) ............................................... 79Connector - BDK Dimpleon ............................. 15Connector - Concentric Tubing Surface .......... 73Connector - Stiff Wireline........................... 87, 95Connector - Surface Tubing .............................. 7Connector - Tubing Grapple............................ 13Connector - Tubing Roll-on ............................. 19

Contact Sub......................................................95Crossover Sub..................................................51

DDart – Precision Displacement.........................53deposits removal ..............................................63Disconnect (UCD) ...........................................79Displacement Dart............................................53Double Dart Check Valve.................................25Double Dart Check Valve - BDK ......................27Double Flapper Check Valve ...........................29Double Flapper Check Valve - .........................31Double Flapper Check Valve with BDK Cartridge

......................................................................31Downhole Filter Sub...........................................9Downhole Phase Separator .............................69Downhole Sensing Tool .................................111Dual Circulation Sub ........................................43

EEntry Sub........................................................115

FFilter Screen.....................................................11Filter Sub - Downhole.........................................9Flapper Check Valve........................................29Flow Release Cable Head - Bakke ..................93

Ggas lift mandrels - avoidance ...........................39Grapple Connector...........................................13Grapple Connector - Snake .............................49

Hhanging up - avoidance....................................39

JJet - Roto..........................................................63Jet – Roto - Options .........................................65

KKick-off Tool .....................................................39

LLatch - Snap.....................................................89

Mmandrels - avoidance.......................................39Moto-head - Bakke...........................................81



NNozzle - Cleanout ............................................ 35Nozzle - Vortex ................................................ 33

OOrientation Tool ............................................. 109

PPacker-Straddle............................................... 77Parabow .......................................................... 83Phase Separator - Downhole .......................... 69Plug Catcher Sub ............................................ 59Position - Kick-off Tool..................................... 39Precision Displacement Dart ........................... 53Pressure Bulkhead - BJ Wireline..................... 97Pressure Bulkhead – Wireline - Bakke............ 99Pressure controlled check-valve ..................... 23

RRelease Cable Head – Bakke Flow................. 93Release Tool ................................................... 91Release Tool - Bakke. & Fishing Spear .......... 37Release Tool - Tension Release ..................... 91Release Tool & Fishing Spear......................... 37removing deposits ........................................... 63Reposition - Kick-off Tool ................................ 39Rod Clamp....................................................... 47Roll-on Connector............................................ 19Roto-Jet ........................................................... 63Roto-Jet - Options ........................................... 65

SSand – Well-Vac.............................................. 71Screen - Surface Filter..................................... 11Separator - Downhole Phase Separation........ 69Sequence Valve .............................................. 23Side Entry Sub............................................... 115Snake Grapple Connector ............................... 49

Snap Latch .......................................................89Standard Threads ..............................................3Steering Tool ..................................................107Stiff Wireline Connector .............................87, 95Straddle Packer................................................77Straight Bar ......................................................45Surface Connector - Concentric Tubing...........73Surface Filter Screen .......................................11Surface Tubing Connector .................................7

TTension Release Tool ......................................91Threads - Standard ............................................3Tornado ............................................................67Tubing Connector - Surface ...............................7Tubing Grapple Connector...............................13Tubing Roll-on Connector ................................19Tubing Surface Connector ...............................73

UUCD - Universal Connect / Disconnect............79Universal Connect / Disconnect (UCD)............79User Comments .............................................117

VVacuum Well – Well-Vac..................................71Valve ................................................................29Valve - BDK Double Dart Check Valve ............27Valve - Double Dart Check Valve.....................25Valve - Double Flapper Check - with BDK

Cartridge.......................................................31Valve - Sequence.............................................23Vortex Nozzle...................................................33

WWellbore Cleaning – Vortex Nozzle .................33Well-Vac ...........................................................71Wireline Connector.....................................87, 95

