CS UNITEC Wet/Dry Vacuum Cleaner - toolsrenewed.comtoolsrenewed.com/New Tools/CS Unitec/DutslessTools.pdf · Industry’s 1st Vacuum To Use CS Unitec's CS 1500 wet/dry dust extraction

CS UNITEC Wet/Dry Vacuum Cleaner

CS UNITEC, Inc. 22 Harbor Avenue, Norwalk, CT 06850

Tel: (203) 853-9522, Toll Free: (800) 700-5919, Fax: (203) 853-9921 Website: www.csunitec.com E-Mail: [email protected]

• Electromagnetic Pulse Cleaning System maintains maximum airflow and suction with automatic filter vibration.

• “Power Take Off” outlet activates the vacuum ON/OFF from the power tool switch. Includes a 7 second shut-off delay to clean any dust in the hose.

• 4 Modes of operation: regular vacuum; power tool activation; auto-clean and auto-clean with power tool activation.

• 99.93% filtration efficiency of particles of 3.0 microns.

• Wet vacuuming capability with sensor for automatic shut off to protect motor and filters.

• Includes a 15’ hose and 25’ power cord for easy portability on jobsite.

Standard Equipment: 2 Filters (P/N 416069), 15’ Hose, Tool Adapter and 25’ Power Cord

Specifications Power 11 Amps / 120 V Max. Tool Rating 15 Amps Air Flow 130 CFM Water Lift 98 Inches Filter Area 9.25 Sq. Ft. Canister Capacity 6.6 gallon Dust Volume Capacity 4.2 gallon Weight 24.3 lbs.

Electromagnetic Pulse Filter Cleaning System vibrates both filters to remove dust. Cleaning can be activated automatically or manually. This maximizes suction and doubles filter life.

MODEL CS 1225

Connect Electric Tools up to 15 AMPS Can Be Used With or Without Filter Bags

With Automatic Pulse Filter Cleaning System and Outlet for Electric Power Tools

Optional Accessories: Filter Bags (P/N 416014),and Cleaning Kit (including wands, nozzles and hose P/N 072401).

http://www.csunitec.com

Industry’s1st Vacuum

To UsePlastic Filter BagsCS Unitec's CS 1500 wet/dry dust extraction vacuum

provides a clean, dust-free environment. The "PowerTake Off" outlet activates the vacuum ON/OFF from thepower tool switch. The Electromagnetic Pulse FilterCleaning System automatically cleans the filters tomaximize air flow, dust collection and suction power.The CS 1500 has a large tank capacity of 13 gallons.

The versatile CS 1500 works in 4 ways:• Without filter bag – dust goes directly into tank• With plastic filter bag for concrete and masonry dust• With paper filter bag for normal dust and soot• With slurry filter bag to capture concrete slurry from

wet drilling, sawing and grinding

For moreinformation onthe CS 1500,please seereverse.

Dust Extraction VacuumWet or Dry

1006-7.5M

CS UNITEC, Inc.22 Harbor Avenue, Norwalk, CT 06850

Toll Free: (800) 700-5919 Tel: (203) 853-9522 Fax: (203) 853-9921Website: www.csunitec.com E-Mail: [email protected]

Note: Specifications subject to change. Refer to Owner's Manual for operating instructions.

Right: Optional VacuumAccessories and Cleaning Kit

Right: Back of CS1500 with optional

Cleaning Kit

ModelCS 1500

Left: Y Splitterfor two tools(included withCS 1500 K)

CS 1500CS 1500 K

includes accessories for one toolincludes accessories for two tools

Wet or dry, 13 gal. capacity with three 10-gallonplastic filter bags and guide handle

CS 1500 Dust Extraction System

Dust Extraction System for Power ToolsCollects concrete dust, concrete slurry,job site debris and more

421742416021420592416069419190

072401

Plastic Filter Bags, 5-packPaper Filter Bags, 5-packSlurry Filter Bags, 3-packFilter Cartridge, 2-packHEPA Filter Cartridge, 2-packCleaning Kit (wands, hose, crevice tool,floor cleaning tool)

Optional Equipment

Three Filter Bag Options:Plastic, Paper and Slurry

CS Unitec, Inc., 22 Harbor Avenue, Norwalk, CT 06850Toll Free: (800) 700-5919 Tel: (203) 853-9522 Fax: (203) 853-9921

Website: www.csunitec.com E-Mail: [email protected]

www.csunitec.com

Filters mountedparallel to motor to

maximize tank space.Located above dustand water levels to

maintain maximum airflow and suction.

Power take-off socketautomatically turnsvacuum ON/OFF via

power tool.

Electromagnetic Pulse Filter Cleaning SystemAutomatically shakes dust from dual-filter system to maintain maximum air flow andsuction power. If airflow is restricted by dirty filters, the vacuum sensor automaticallyactivates the cleaning mode when the power tool is turned off. Manual activation isalso available.

Polyester Filters – Washable and ReusableSave time and money – no need to carry spares. These filters are washable andreusable. Large surface area of 1,333 square inches. Standard filters (P/N 416069)capture 99.93% of all particles 0.3 microns and larger. Optional HEPA filters(P/N 419190) capture 99.9977% of all particles 0.3 microns and larger.

Built-in Power Take-Off Socket – up to 15 AmpsAutomatically turns vacuum ON/OFF from the power tool switch. Accepts 15-amptools. When the tool is turned off, the vacuum runs for 7 seconds to clear the hose.

Quiet OperationLow noise level – only 69 dba.

High Mobility and DependabilityLarge wheels, locking front casters, 26-ft. power cord and removable handle allow foreasy maneuverability and transport.

No-Memory, Non-Static Heavy-Duty Hose15' hose always maintains its shape – no kinking or knots.

Three Filter Bag Options; Four Ways to Use Vacuum

No Filter Bag – Dust goes directly into tank.

Plastic Filter Bag – Holds more than 20x the amount ofconcrete dust collected by paper filter bags. With a capacity ofup to 10 gallons, plastic filter bags are ideal for fine concretedust that would otherwise clog pores of paper bags. Tie stripcloses bag to seal in dust for easy disposal. The special airguide maintains equal vacuum pressure inside and outsidethe bag to make it possible to use the plastic filter bags. Withthe largest capacity in the industry, plastic filter bags needfewer changes, saving you time and money.

Paper Filter Bag – For general debris collection, includingnormal dust and soot.

Slurry Filter Bag – Captures concrete slurry and allows thewater to pass through the porous wall of the bag into the tank.This prevents the concrete from hardening in the tank. Slurryfilter bags make for easy disposal of the concrete waste,preventing environmental pollution.

Dust Extraction VacuumWet or Dry

Versatile, Dependable Dust Extraction System for Power Tools.Collects concrete dust, concrete slurry, job site debris and more.

The CS 1500 Vacuum features:

No-memory,non-static hose alwaysmaintains its shape –

never any kinks orknots.

Up To 15 AMPS

The CS 2000 water recycling vacuum is ideal for contractors who usediamond core drills, masonry saws, grinders and other wet-working tools.An integrated sump pump delivers water from the tank to the tool, thenthe vacuum suction brings the water back to the tank and into a porousfilter bag. Slurry and debris are captured and the clean water flows backinto the tank for delivery back to the tool. This system saves time andallows safe, easy disposal of the slurry.

The CS 2000 is 4 Tools in 1:• Portable water supply for power tools – saves time

with fewer interruptions for refilling water tanks. Keepswork site clean and traps slurry for easy waste disposal.

• Flood vacuum cleaner – picks up large volumes ofwater in a short time from flooded areas, includingbasements, and pumps it out of the location. Also idealfor draining water from pipes.

• Pond and pool cleaning – efficiently vacuums particlesup to 3/8" dia., including algae, mud and foliage. Thematerial is captured in the porous filter bag. The clearwater can be pumped back into the pond/pool.

• Universal wet/dry vacuum cleaner

Water Recycling andSlurry Containment Vacuum

0107

Note: Specificationssubject to change. Referto Owner's Manual foroperating instructions.

Right: VacuumSystem includes

vacuum hose, waterrecycling/discharge

hose, slurry filterbags and owner's

manual.

For more information on the CS 2000, please see reverse.

Left: Integrated sumppump can recycle ordischarge water.

Water Recycling System for Power Tools, FloodReclamation, Pond/Pool Cleaning and Wet/Dry VacuumingSlurry and debris contained in filter bag – clean waterpasses into the tank for recycling

Model CS 2000and attachments

Power

Water CapacityPump Output

Water LiftWater PressureAir FlowCanister VolumeCanisterDimensionsWeight

CS 2000 Water Recycling/Slurry Containment System

17 Amp, 115 VAC/60Hz, 1-phase(includes 11 Amp Vac motor and 6 Amp sump pump)

7 gallons78 GPM at ground level10.5 GPM at 10 ft. discharge height18 ft. max. discharge height14.5 PSI (pump delivery)150 CFM13 gallonsStainless steel tank with cart20.5" W x 21.6" L x 39.5" H59 lbs.

420592416021072401

Slurry Filter Bags, 3-packPaper Filter Bags, 5-packCleaning Kit(includes wands, hose, crevice tool and floor cleaning tool)

Optional Equipment



CS Unitec, Inc., 22 Harbor Avenue, Norwalk, CT 06850Toll Free: (800) 700-5919 Tel: (203) 853-9522 Fax: (203) 853-9921

Website: www.csunitec.com E-Mail: [email protected]

www.csunitec.com

Power socket forintegrated sump pump.

Two switches operatemotor and pumpindependently.

The CS 2000 vacuum features:

Integrated Submersible Sump Pump with Replaceable Filter SleevePowerful, robust operation has a flow rate of 78 gallons per minute at level and a maximum

water lift of 18 feet. Delivery is 10.5 GPM at 10 feet.

Secure, Reliable ConnectionsPower cable plug for sump pump and water recyclingor discharge hose connection.

Heavy-duty SealsHeavy-duty plugs seal vacuum for normal wet/dry cleaningand transport.

Water Recycling andSlurry Containment Vacuum

Versatile, Heavy-duty Water Recycling System for Power Tools and Other Applications.

Slurry and debris are captured in a porous filter bag – clean water flows into tank andcan be cycled in a continuous loop or pumped out of the area.

The CS 2000 saves time and money, benefiting both the environment and your bottom line.Work FasterWith both a portable water supply and a continuous loop system, you will conservewater and save time normally used for refilling portable pumps.

Work CleanerThe slurry containment and vacuum system keeps the work area clean and dry – spendless time cleaning up. Ideal for indoor and outdoor applications such as hospitals, officebuildings, factories, patios and more.

Work More Environmentally FriendlySlurry is contained in a porous filter bag, allowing for safe, easy, proper waste disposal. Stainless steel

canister can either betilted (above) or lifted

out of cart (below).

Large wheels, lockingfront casters, 26-ft.

power cord andremovable handle

allow for easymaneuverability and

transport.

When wet drilling, cutting orgrinding, water can be

continuously pumped to thework area, then vacuumed

and filtered in the tank.Above: Watercollection ringallows vacuum

attachment.

Concrete Grinderwith Dust Extraction

Motor PowerWeightLoad Speed

Model EBS 125

14 AMP/110 Volt9 lbs.10,000 RPM

The EBS 125 Concrete Grinder is held by two side handles. This ergonomic “H” design differsfrom traditional right angle grinders and allows theoperator to finish larger surfaces with less fatigue.Additionally, the motor is set above the grindingwheel in a dust-free zone, resultingin longer tool life.

A brush shield protectsagainst dust and enablesadjustment of the workingheight to the wear of thediamond grinding wheel. Also,the EBS 125 has a removablefront dust guard for finishingconcrete floors into thecorners and edges. Thisallows grinding right up to thewall (see below).

An optional walk-behind cart(P/N 37210, shown above) allows for comfortableoperation of the EBS 125 Concrete Grinder. Theperfect addition to virtually dust-free grinding whenused with the CS 1225 vacuum (see left).

Model EBS 125 D includes one premium diamondwheel (P/N 253.115).

Removable front dust guard

With optionalwalk-behind cart

and vacuum

Standard Equipment includes:Spanner wrench, open-ended wrenchand metal carrying case.

Accessories:P/N 253.115 5” Diamond Grinding Wheel for paint, epoxy, thermoplastics, adhesives and hard coatings.

P/N 253.115 C5” Diamond Grinding Wheel for finishing clear concrete, green concrete, mortar and masonry.

P/N 37210Walk-behind cart.

Concrete Surface Preparation with Dust CollectionModel EBS 125

• Remove paint, epoxy, glue and other hard coatings

• Smooth rough surfaces

• Clean concrete before applying new paint or coatings

• Collect dust for clean working area with CS 1225 dust extraction vacuum

EIBENSTOCK TOOLS

5M-0206



Note: Specifications subject to change. Refer to Owner'sManual for operating instructions.


Motor PowerCapacityWeightLoad Speed

Model EBS 180116 AMP/110 Volt5" diameter12 lbs.10,000 RPM

Concrete Grinder 5" with Dust Extraction

The most powerful in its class!

The EBS 1801 Concrete Grinder removespaint, epoxy, glue and other hard coatings. Itcan be used to prepare roughconcrete and floors forapplication of new epoxyand/or coatings. This grinder issolidly built with a 16 AMPmotor to enable a high loadcapacity. The EBS 1801Concrete Grinder is especiallysuited for hard jobs, such asthe grinding of two componentadhesives.

• High-performance motor is located above thediamond grinding wheel, away from dust, toextend the life of the grinder

• Brush shield allows the user to adjust theheight of the grinder to the wear of thediamond wheel and protect against dustand debris

• Electronic features include soft start,overcurrent cut-off and optical overloadindication

• Front edge of the dust guard is removableto allow grinding right up to the wall

• Optional walk-behind cart is availableto eliminate kneeling or bending whilegrinding and to provide more comfort to the user (P/N 37210)

• Collect dust for clean working area with CS 1225 and CS 1500 wet/dry vacuums

Standard Equipment includes:Diamond Grinding Wheel and metal carrying case

Accessories:P/N 253.115 5" Diamond Grinding Wheel for epoxy, thermoplastics, paint, adhesives and hard coatings

P/N 253.115 C5" Diamond Grinding Wheel for finishing clear concrete, green concrete, mortar and masonry

P/N 37210Walk-behind cart

• Remove epoxy, glue, paint and other hard coatings

• Smooth rough surfaces or clean concrete beforeapplying new paint or coatings

• Powerful 16 AMP motor with high load capacity

• Collect dust for clean working area with CS Unitec'sCS 1225 or CS 1500 dust extraction vacuum

EIBENSTOCK TOOLS

0907




Removable front dust guard forgrinding up to

walls and edges.

Motor PowerCapacityWeightLoad Speed

Model EBS 18022 AMP/110 Volt7" diameter21 lbs.6,000 RPM

The 7" EBS 180 walk-behind Concrete Floor Grinder prepares roughconcrete and floors for the application of new epoxy and/or coatings.It can be used to remove epoxy, glue, paint and other hard coatings.The EBS 180 Concrete Floor Grinder weighs only 21 lbs. It makesfinishing large areas easy by eliminating kneeling and bending, thusincreasing user comfort.

• High-performance motor is located above the diamond wheel, away from dust and debris, to extend the lifetime of the grinder

• Brush shield allows the user to adjust the height of the grinder to protect the unit from surface dust, dirt and stones

• Electronic features include soft start, temperature control,overcurrent cut-off and constant speed

• Collect dust for clean working area with CS 1225 and CS 1500wet/dry vacuums

Standard Equipment includes:7" Diamond Grinding Wheel

Accessories:P/N 253.1177" Diamond Grinding Wheel for epoxy, adhesives, paint and hard coatings

P/N 371127" Diamond Grinding Wheelfor clear (uncoated) concrete

• Fast removal of epoxy, glue, paint and other hard coatings

• Smooth rough surfaces or clean concrete before applying new paint or coatings

• Walk-behind operation is comfortable for operator when workingon large areas – eliminates kneeling and bending

• Powerful 22 AMP motor with high load capacity

• Collect dust for clean working area with CS Unitec's CS 1225 orCS 1500 dust extraction vacuum

EIBENSTOCK TOOLS

0907




Concrete Floor Grinder 7"with Dust Extraction

Powerful 22 AMP MotorOnly 21 lbs. – Easily Portable

DUST EXTRACTION TOOLS CONCRETE GRINDER AND VACUUM


Tel: (203) 853-9522, Toll Free: (800) 700-5919, Fax: (203) 853-9921Website: www.csunitec.com E-Mail: [email protected]

CS 1225 Industrial Vacuum withAutomatic Filter Cleaning SystemDust extraction vacuum –includes “power take-off” outletfor electric tools. ElectromagneticPulse Filter Cleaning System vibratestwo filters to remove dust. Ideal forconcrete and masonry applications.

LD 1509 FR 5” Concrete GrinderRemoves all kinds of coatings fromconcrete surfaces. Clean workingconditions when used with an industrialvacuum. No rasping or jumping,perfect for spot jobs and edging.11 AMP/10,000 RPM.Wt.: 6 lbs Vacuum port: 1-1/4”

Model LD 1509 FRD includes (1) 5”Premium Diamond Grinding Wheel(part no. 253.115)

Standard Equipment:Clamping Flange (191.612)Hose Clip (252.050)Accessories:5” Diamond Grinding Wheel (253.115)Carrying Case (252.185)

Thermo-Jet Diamond Wheel withlarge holes for dust extraction5” Thermo-Jet PN.253.1157” Thermo-Jet PN.253.117


Concrete Repair Toolswith Dust Extraction

5M-0206



Dust Extraction System for Power ToolsCS 1225 Wet/Dry Vacuum Cleaner With AutomaticFilter Cleaning System

High vacuuming power (130 CFM) provides a clean, dust-freeenvironment for the operator. "Power Take Off" outlet activatesvacuum ON/OFF from the power tool switch. Electromagnetic PulseFilter Cleaning System vibrates two filters to remove dust. Cleaningcan be activated automatically or manually. Includes 2 filters(416069), 15' Hose, Tool Adapter and 25' Power Cord.

Joint Cutter with Vacuum PortFor Tuck Pointing JobsModels F 1509 FR and F 1509 FRDRemoves brittle mortar from long and generally horizontal brick joints for rapid restoration of old brick buildings. Clear view of joints.Adjustable cutting depth to 1".Motor: 11 AMP; 10,000 RPM; Arbor: 7/8"; Wgt: 7.5 lbs.Vacuum Port: 1-1/8" dia.Model F 1509 FRD includes:(1) 5" Premium Diamond Blades (252.290).Standard Equipment:Holding Wrench (100.110)Open-end Wrench (106.461)4mm Hex Key (211.494)(3) Cable Clips (252.188)Metal Carrying Case (256.464)Accessories:Premium Diamond Blade (252.290) 5" x .080" x 7/8"Premium Diamond Blade (252.291) 5" x .250" x 7/8"

Wall Slotter with Vacuum PortFor Cutting Concrete and MasonryModels M 1509 FR and M 1509 FRDIdeal for cutting a channel for wires, cables, etc.Cutting widths of 3/8"; 5/8" or 7/8".Cutting depth up to 1-3/16".Motor: 11 AMP; 10,000 RPM; Arbor 7/8"; Wgt: 8 lbs.Vacuum Port: 1-1/8" dia.Model M 1509 FRD includes:(2) 5" Premium Diamond Blades (252.290)Standard Equipment:Holding Wrench (100.110)Open-end Wrench (100.102)Web Remover (slot chisel) (229.253)Set of Clamping Washers (251.479)(3) Cable Clips (252.188)4mm Hex Key (211.494)Metal Carrying Case (256.464)Accessories:Premium Diamond Blade (252.290) 5" x .080" x 7/8" (2 Required)

Note: Specifications subject to change.Refer to Owner's Manual for operating instructions.


Scouring Machinewith Dust Extraction

5M-0206

EPF 1502



Note: Specifications subject to change.Refer to Owner's Manual for operating instructions.

Extremely Versatile.

The new EPF 1502 Scouring Machine enablesthe user to knock off plaster, roughenconcrete, level screed or remove old paint. The13.6 AMP motor is powerful enough to scarifylarge surfaces. The dust guard is verticallyadjustable and connects directly to a standardvacuum hose. The combination of a verticallymounted motor and dust guard extends the lifeof the tool by keeping dust away from themotor. The ergonomically designed toolreduces user fatigue.

This is an ideal tool forprofessional renovation.The EPF 1502 will roughen,descale, abrade, clean andtexturize, as well as removeplaster, old paint, adhesives,plastics and resins.

PowerRated VoltageMilling Head DiameterLoad Speed (min-1)SpindleWeight

13.6 AMP110 Volt5"4000 RPMM 1410 lbs.

Spare Cutting Teeth Sets (1 Set = 16 pcs.)

37421 Milling star, diagonal teeth (incl. washers)width 1/8" each

37422 Milling star, straight teeth (incl. washers)width 1/8" each

Roughen Concrete and Quickly Remove Plaster

and Paint Dust-free

EIBENSTOCK TOOLS


Documents

CS UNITEC Wet/Dry Vacuum Cleaner - toolsrenewed.comtoolsrenewed.com/New Tools/CS Unitec/DutslessTools.pdf · Industry’s 1st Vacuum To Use CS Unitec's CS 1500 wet/dry dust extraction