Common to All Models WARNING: Condenser fins are sharp, gloves are recommended to avoid injury. • Clean the condenser every 3 - 6 months. • Condensers look like radiators with looping copper tubing. • With pets, consider cleaning more often. • Use a brush attachment and vacuum to remove debris from the condenser. • Refer to the Use & Care Guide for additional guidance. • Be cautious not to bend the aluminum fins of the condenser. •If flashing service, wrench icon, other error indicators return or temperatures do not improve, contact factory certified service for assistance. •Use mild detergent and warm water to clean grilles and kickplates and dry before reinstalling. Do not remove foam strips. 600, 500, 200/300 Series & Model 430 Excludes models listed separately Stainless Steel & Framed Units 1. Press Unit ON/OFF on the control panel to turn the unit off. 2. Open the door(s) and remove (2 or 3) Phillips screws going up into the bottom of the grille. 3. Tilt the grille forward from the top and release (1 or 2) springs attached behind the grille to remove it. 4. Vacuum the condenser facing outer right. 5. Turn the unit back on after replacing the grille. Overlay Units 1. Follow instructions above. 2. To remove the grille, push up on the solid panel covering the grille area, pull out at the bottom and pull down to release the panel grille from the mounting bracket. 3. Turn the unit back on after replacing the grille panel. 601R, 601F, 501R, 501F, 201R, 201F Stainless Steel, Framed and Overlay Units 1. Press Unit ON/OFF on the control panel to turn unit off (601) or turn the control dial down past 1 to OFF (501, 201). 2. Remove (2) black screws in the lowest louver of the grille, one located on each side of the grille. 3. Tilt the bottom of the grille out and away to release the top of the grille. 4. Vacuum the condenser facing forward. 5. Turn the unit back on after replacing the grille. Built-In (BI) Series, PRO48 Models 1. Press POWER on the control panel to turn unit off 2. Grasp the center of the grille assembly at the bottom, lift and rotate the grille up to expose the condenser area. 3. Remove the water filter for easier access if needed. 4. Carefully vacuum the condenser facing outer right. 5. Turn the unit back on after closing the grille area. Integrated, 700 Series, 427 & 427R Models 1. Press Unit ON/OFF on the control panel to turn unit off. 2. Remove the lower drawer by pulling up and out. CAUTION: This exceeds 25 lbs of lifting. 3. Remove (4) screws at each corner of the kick- plate and slide it forward to remove. 4. Carefully vacuum the condenser facing forward. 5. Turn the unit back on after reinstalling the kick- plate. Undercounter (UC) Series, 249, 245, 505, 506, 315I, UC-15I, 424 and 315W Models 1. Turn the unit off at the control panel or control knob. 2. Remove the screws on both sides of the kickplate. 3. Carefully vacuum the condenser facing forward. 4. Turn the unit back on after reinstalling the kick- plate. SUB-ZERO, INC. P. O. BOX 44988 MADISON, WI 53744 SUBZERO-WOLF.COM 800-222-7820 Condenser Cleaning Guide

Condenser Cleaning Guide for Customersdocuments.subzero.com/AnswerAdvisor/Condenser Cleaning Guide.pdf4. Carefully vacuum the condenser facing forward. 5. Turn the unit back on after

Download PDF Report

Upload
others
View
5
Download
0

Embed Size (px)

Citation preview

Page 1: Condenser Cleaning Guide for Customersdocuments.subzero.com/AnswerAdvisor/Condenser Cleaning Guide.pdf4. Carefully vacuum the condenser facing forward. 5. Turn the unit back on after

Common to All ModelsWARNING: Condenser fins are sharp, gloves are recommended to avoid injury.

• Clean the condenser every 3 - 6 months.• Condensers look like radiators with looping copper tubing.• With pets, consider cleaning more often.• Use a brush attachment and vacuum to remove debris from the condenser.• Refer to the Use & Care Guide for additional guidance.• Be cautious not to bend the aluminum fins of the condenser.

•If flashing service, wrench icon, other error indicators return or temperatures do not improve, contact factory certified service for assistance.•Use mild detergent and warm water to clean grilles and kickplates and dry before reinstalling.Do not remove foam strips.

600, 500, 200/300 Series & Model 430Excludes models listed separately

Stainless Steel & Framed Units

1. Press Unit ON/OFF on the control panel to turn theunit off.2. Open the door(s) and remove (2 or 3) Phillips screws going up into the bottom of the grille.3. Tilt the grille forward from the top and release (1 or 2) springs attached behind the grille to remove it.4. Vacuum the condenser facing outer right.5. Turn the unit back on after replacing the grille.

Overlay Units

1. Follow instructions above.2. To remove the grille, push up on the solid panel covering the grille area, pull out at the bottomand pull down to release the panel grille from the mounting bracket.3. Turn the unit back on after replacing the grille panel.

601R, 601F, 501R, 501F, 201R, 201FStainless Steel, Framed and Overlay Units

1. Press Unit ON/OFF on the control panel to turn unit off (601) or turn the control dial down past 1 to OFF (501, 201).2. Remove (2) black screws in the lowest louver of the grille, one located on each side of the grille.3. Tilt the bottom of the grille out and away to release the top of the grille.4. Vacuum the condenser facing forward.5. Turn the unit back on after replacing the grille.

Built-In (BI) Series, PRO48 Models1. Press POWER on the control panel to turn unit off

2. Grasp the center of the grille assembly at the bottom, lift and rotate the grille up to expose the condenser area.3. Remove the water filter for easier access if needed.4. Carefully vacuum the condenser facing outer right.5. Turn the unit back on after closing the grille area.

Integrated, 700 Series, 427 & 427R Models1. Press Unit ON/OFF on the control panel to turn unit off.2. Remove the lower drawer by pulling up and out.CAUTION: This exceeds 25 lbs of lifting.3. Remove (4) screws at each corner of the kick-plate and slide it forward to remove.4. Carefully vacuum the condenser facing forward.5. Turn the unit back on after reinstalling the kick-plate.

Undercounter (UC) Series, 249, 245, 505, 506, 315I, UC-15I, 424 and 315W Models1. Turn the unit off at the control panel or control knob.2. Remove the screws on both sides of the kickplate. 3. Carefully vacuum the condenser facing forward.4. Turn the unit back on after reinstalling the kick-plate.

SUB-ZERO, INC. P. O. BOX 44988 MADISON, WI 53744 SUBZERO-WOLF.COM 800-222-7820

Condenser Cleaning Guide

http://www.subzero-wolf.com/professional-kitchen/kitchen-plans.aspx