APPLICATIONS Standard coiled tubing interventions oil,
gas, and injector wells Standard HPHT operations Perforating
Jarring/impact hammers Milling
ADVANTAGES Rotational lock holds high amount of torque Reusable
connectors offer multiple use Minimal ID restriction of the CT,
allowing
unrestricted flow and the use of wiper plugs or process
balls
Allows coiled tubing preparations at base Sweet and sour
services according to
NACE standards Quick installation and removal
Two O-rings seal on the coil High-strength construction
makes
the connector stronger than the coiled tubing string
Uses 12 knurled grub screws
Historically, the external set screw, or dimple connector, has
been the preferred style of connector. It is attached to the coiled
tubing end by set screws that engage preformed dimples, which are
formed using a dimpling tool. After the dimpling, the coiled tubing
end is prepared for the O-ring seal by beveling off the end and
smoothing the O-ring seal area. The connector is then slipped up
the coiled tubing; the set screws are torqued in place.
Verification of proper installation is required with a pressure and
pull test.
The dimple connectors are available standard CT sizes of 1 in, 1
in, 2 in, 2 in, and 2 in.
Dimple ConnectorQuickly installs and removes
Dimple connector.
*Mark of SchlumbergerCopyright 2014 Schlumberger. All rights
reserved. 13-CT-0061
slb.com/CoilTOOLS
Specifications Part Number OD,
in [mm]ID, in [mm]
CT Size Lower Thread Will Pass Ball Size, in [mm]
Make-up length, in [mm]
Sweet and sour services
Working Pressure, psi [kPa]
Tensile Strength, lbf [daN]
Torque Capacity, ft-lbf [daN-m]
100476698 1.69 [42.926]
0.812 [20.625]
1-in CT 1-in AMMT-S PIN
0.75 [19.05]
6.68 [169.672]
Yes 10,000
[68,948]
31,790
[14,141]
374
[51]
100297852 2.13 [54.102]
1.03 [26.162]
112-in CT 112-in AMMT-S PIN
1 [25.4]
6.68 [169.672]
Yes 10,000
[68,948]
63,772
[28,367]
1,237
[168]
100297854 2.13 [54.102]
0.812 [20.625]
112-in CT 1-in AMMT-S PIN
0.75 [19.05]
6.68 [169.672]
Yes 10,000
[68,948]
31,790
[14,141]
374
[51]
100289510 2.875 [73.025]
1.38 [35.052]
134-in CT 238-in PAC DSI PIN
1.25 [31.75]
6.68 [169.672]
Yes 10,000
[68,948]
97,650
[43,437]
2,749
[373]
100288814 2.25 [57.15]
1.03 [26.162]
134-in CT 112-in AMMT-S PIN
1 [25.4]
6.68 [169.672]
Yes 10,000
[68,948]
57,034
[25,370]
1,237
[168]
100297129 2.56 [65.024]
1.03 [26.162]
2-in CT 112-in AMMT-S PIN
1 [25.4]
6.68 [169.672]
Yes 10,000
[68,948]
63,772
[28,367]
1,237
[168]
100297134 2.875 [73.025]
1.38 [35.052]
2-in CT 238-in PAC DSI PIN
1.25 [31.75]
6.68 [169.672]
Yes 10,000
[68,948]
97,650
[43,437]
2,749
[373]
100476229 2.875 [73.025]
1.38 [35.052]
238-in CT 238-in PAC DSI PIN
1.25 [31.75]
8.5 [215.9]
Yes 10,000
[68,948]
74,326
[33,062]
2,749
[373]
100626341 3.13 [79.502]
1.25 [31.75]
238-in CT 238-in API REG PIN
1.125 [28.575]
8.5 [215.9]
No 10,000
[68,948]
124,992
[55,599]
4,000
[542]
100549919 3.13 [79.502]
1.25 [31.75]
238-in CT 238-in API REG PIN
1.125 [28.575]
8.5 [215.9]
Yes 10,000
[68,948]
124,992
[55,599]
4,000
[542]
100675642 3.375
[85.725]
1.75
[44.45]
278-in CT 238-in API IF
PIN
1.625
[41.275]
8.5
[215.9]
Yes 10,000
[68,948]
84,758
[37,702]
3,778
[512]
100288815 3.375 [85.725]
1.38 [35.052]
278-in CT 238-in PAC DSI PIN
1.25 [31.75]
8.5 [215.9]
Yes 10,000
[68,948]
84,758
[37,702]
3,778
[512] Values are based on 80-ksi strength steel at 70 degF [21
degC] and a single load case. At temperatures above 250 degF [121
degC] all ratings for the tool are reduced by 7%, at 350 degF [177
degC] the ratings are reduced by 12%. All users should determine
the actual operating and load parameters for their own
application.
Dimple Connector
