COATING SOLUTION - I-CanNano SOLUTION.pdf · contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. Self-organizing

I-CanNanoTM

225 Innovation Center for Applied Nanotechnology - I-CanNanoTM

India: 22A Hemchandra Mukheerjee Road, Barisha, Kolkata -700 008. Ph.: +91 33-32985444, e-mail:[email protected]

COATING SOLUTION

I-CanNanoTM



I-CanNanoTM



Nano Anti-Damp Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product

contains specially modified Functional Nano Particles that are specially linked into a Silicon

Matrix in a Solvent Base. Self-organizing Nano components form an invisible layer on the

surface with excellent water and oil repellent properties. n-constrkoat is a high performance,

multifunctional coating with many key functional properties combined together in one

coating solution.

BENEFITS & ADVANTAGES

Water repellant (hydrophobic) and Dirt repellent (oleo phobic),

UV Resistant ,

Anti-Bacterial / algae, Thermal Shock Absorption,

Breathable (air can water can’t pass through),

It allows water to roll-off the surface forming a Brushing Effect (Self-Cleaning

Effect),

No dampness develops on the surface ,

Transparent,

Easy application through Spray, Brush,

Material can be cured at atmospheric temperature,

Stable at varying Temperatures,

Low Cleaning and Maintenance Cost,

Ecologically beneficial and biologically safe,

It helps to retain the quality of the surface.

AREAS OF APPLICATION: Can be applied on exterior walls of buildings as TOPCOAT, buildings

with Brick exterior, buildings with plaster exterior, brick Walls/Slabs, Exposed RCC, painted

building exterior walls , painted building interior walls etc. This coating should be applied as

topcoat over plaster/brick/ painted surfaces.

APPLICATION INSTRUCTIONS

Mixing/Dilution: The material does not require any mixing or dilution . Application of

the material as delivered from original packaging is recommended.

Cleaning of the Surface: It must be ensured that the surface is free of all loose

particles/ Dust etc. Before application of the coat the Plaster/ Brick/ Painted

Surface should be cleaned and completely dried.

Application of Coating Solution: The material can be applied on the surface by

either by Spray, Brush, Roller etc. It should be ensured that the material is

adequately applied until the surface is saturated (This may vary for different

I-CanNanoTM



surfaces, usually rough & absorbing surfaces may consume more material than

smooth surfaces. On an average, a liter of the coating material should be sufficient

for about 150 Sq Ft.).

Application Conditions: Ambient temperature: Coating can be applied in ambient

temperature conditions (i.e. 10 Deg C to 40 Deg C).

Humidity level: 60% to 80%. Deviating conditions can influence the formation of

hydrophobic effect and drying time. Coating should be applied and dried in a dust

free environment, if possible, in clean room conditions. Application should be

avoided under high humid/moist/rainy conditions.

Curing: The Coating takes about 6 Hrs to completely set.

Test of Coating: Once coated the performance can be tested by pouring some water

on the coated panels. If properly coated, the water should form droplets and roll-off.

VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent

STORAGE: Shelf life is of at least 12 months in sealed original packing. In case of

overstepping, the quality of the material should be tested again. The material should be

protected against heat, frost and moisture.

PACKING: 1/10/50 Liters

I-CanNanoTM



Nano Stone Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, this synthesized product


Matrix in a Solvent/water Base. Self-organizing Nano components form an invisible layer on

the surface with excellent water and oil repellent properties. NANO STONE COATING is very

versatile. It has special additional properties like UV protection and anti-bacterial protection

BENEFITS & ADVANTAGES:

Water repellent (hydrophobic) and Dirt repellent (oleo phobic),

Properties such as UV Resistance, Anti-Bacterial property are incorporated,

The water rolls-off the surface forming a Brushing Effect (Self-Cleaning Effect),

Easy application through Spray/Brush,

Material can be cured at atmospheric temperature,

Stable at varying temperatures.

Low Cleaning and Maintenance Cost.

It is ecologically beneficial and biologically safe,

It retains the quality of the surface,

It provides resistance against: Dirt, Algae, etc.

AREAS OF APPLICATION: Buildings with Stone exterior, Buildings with stone interior, Stone

Sculptures, Stone Walls, Stone Slabs, dholpur/ yellow/jaisalmer/natural/black/marble stones

etc. are all potential areas for the application of this material.


Mixing/Dilution: The material requires no mixing or dilution . The material can be

applied directly as delivered from original packaging.

Cleaning of Surface: It must be ensured that the surface is free of all loose

particles/ dust etc. Before application the Stone/ Brick Surface must be clean and

completely dry.


temperature conditions (i.e. 10 Deg C to 40 Deg C). In this case, drying time would be

around 3 hours. Humidity level: 60% to 80%. Deviating conditions can influence the

formation of hydrophobic effect and drying time. Coating should be applied and dried

in a dust free environment, if possible, in clean room conditions. Application of

coating should be avoided under high humid/moist/rainy conditions.


either by Spray, Brush, Roller etc. It should be ensured that the material is

adequately applied until the surface is saturated (This may vary for different

surfaces, usually rough & absorbing surfaces may consume more material than

I-CanNanoTM



smooth surfaces. On an average, a liter of the coating material should be sufficient

for about 70 – 100 Sq Ft). Solvent based coating and water based coating should be

applied for smooth and rough surfaces respectively.

Test of Coating: The Coating takes about 6 Hrs to completely set. Once coated the

performance can be tested by pouring some water on the coated panels. If properly

coated, the water should form droplets and roll-off.

VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent/white




PACKING: 1/10/50 Liters

I-CanNanoTM



Nano Ceramic Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, this synthesized product


Matrix in a Solvent Base. Self-organizing Nano components form an invisible layer on the

surface with excellent Water/Dust Repulsion & Anti-bacterial properties. Product n-cerkoat is

high performance multifunctional coating with many key functional properties combined

together in one coating solution.

BENEFITS & ADVANTAGES: It is a stain-free, Water repellant (hydrophobic) , Dirt repellent

(oleo phobic), Anti-Bacterial / algae/ foul, Scratch Resistant, Anti-sticking, Anti-corrosive ,

and an easy clean product. It permits water to roll-off the surface forming a Brushing Effect

(Self-Cleaning Effect). Other benefits provided by this product hail from its ability to avoid

dampness on the surface and its transparency. Easy application through Spray/Brush, curing

at atmospheric temperature, stability at varying temperatures, low cleaning and

maintenance costs and the fact that this product is ecologically beneficial and biologically

safe makes this product perfectly tailored for industry usage . It also helps to retain the

quality of the surface.

AREAS OF APPLICATION: Areas of application include Ceramic wall tiles, Ceramic sanitary

wares, Ceramic bath-wares, Ceramic Wash-Basins, Ceramic Commode/ Urinals, Water-less

urinals.

UNSUITABLE FOR: Plaster, natural stone, metal or plastic surfaces.


Mixing/Dilution: No mixing or dilution of material should be done. The material

should be delivered directly from original packaging.

Cleaning of the Surface: It must be ensured that the Surface is free of all loose

particles/ dust etc. Before application the ceramic surface must be clean and

completely dry. This coating should be applied as topcoat over ceramic surfaces.


either Spray, Brush, Roller, Sponge, Tissue paper etc. It should be ensured that the

material is adequately applied until the surface is saturated (This may vary based on

efficiency of applicator. On an average, a liter of the coating material should be

sufficient for about 700 Sq Ft.).

Application conditions: Between + 10 °C (283 K) and + 40 °C (313 K) air and object

temperature; dew temperature should be taken into account when working at low

temperatures. Relative Humidity level should lie between 60% and 80% . Application

process needs to be done in clean & dust-free environment. Application should be

avoided in moist/ humid & rainy environment.

I-CanNanoTM



Curing: The coating takes about 3 Hrs to get set completely.

Polishing: After 3 hours the surface should be wiped out with a clean & dry tissue

paper and should then be polished till it becomes completely dry.

Testing: Once coated the performance can be tested by pouring some water on the

coated tiles. If properly coated, the water should form droplets and roll-off.

CLEANING & MAINTENANCE OF THE COATED SURFACE: Periodically scaly residues,

deposited salts and dirt must be removed with a nylon brush, if necessary, mild detergents

may also be used. Use of strong detergents and alkali for cleaning purposes is strictly

prohibited.

TOUCH UP & RE-COAT: Existing coatings need not be removed; surface should be prepared

as per above instructions and then recoated.

VISCOSITY: 15 sec SPECIFIC GRAVITY: 0.81 COLOR: Transparent CHEMICAL RESISTANCE TESTS

BIS Standard BIS+ Standard Name of

Chemical

Strength

Condition Result Condition Resul

t

Acetic Acid 10% 16 hrs, 100 Deg C Pass 72 hrs, 100 deg C Pass

Citric Acid 10% 16 hrs, 100 Deg C Pass 72 hrs, 100 deg C Pass

Detergent ---- 48 hrs, 60 Deg C Pass 72 hrs¸100 deg C Pass

Hydrochloric Acid 50% 48 hrs, 25–35 Deg C Pass 72 hrs, 35 deg C Pass

Sodium Hydroxide 5% ½ hrs, 60 Deg C Pass 24 hrs, 100 deg C Pass

Sodium Stearate 0.15% 48 hrs, 60 Deg C Pass 72 hrs, 100 deg C Pass

Sulphuric Acid 3% 16 hrs, 100 Deg C Pass 72 hrs, 100 deg C Pass

STAIN RESISTANCE TESTS BIS Standard Result

0.5% Methyl Blue Soln. Pass. No stain

10% Sodium Hypochlorite Pass. No stain.

3% Hydrogen Peroxide Pass. No stain.

Amyl Acetate Pass. No stain.

Carbon Tetrachloride Pass. No stain.

Iodine with ethanol Pass. No stain.

OTHER TESTS

Test Result

I-CanNanoTM



Contact Angle of water droplets 1180

Thickness of coating (Dektak Profilometer) 530A

Abrasion Resistance Improved

Cold Test ( -20ºC for 2 Hrs.) Pass

Bake Test (130ºC for 2 Hrs.) Pass

Anti-bacterial Test No bacteria growth

Humidity Test ( 50ºC & 99.99% RH for 360hrs) Pass

Salt Spray (Keep the coated tiles at 5% NaCl salt chamber for 360 hrs) Pass

Water immersion test (immersed in water for 360 hrs at room temp.) Pass

Boil Test (Boil the coated ceramic tiles at 100ºC for 2 Hrs.) Pass

Temperature withstand ability Above 3000

Scratch Resistance Improved

Contact angle post abrasion test No significant change

UV Radiation Test (2 sun intensity for 100 Hrs.) Pass

Acid Test (pH=1) & Alkaline Test (pH=11) Pass




PACKING: 0.5/1/10 Liters

I-CanNanoTM



Nano Glass Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product n-

glaskoat contains specially modified Functional Nano Particles that are specially linked into a

Silicon Matrix in a Solvent Base. NANO GLASS COATING material, when applied on Glass

surface forms a thin layer with excellent Roll-Off behavior for water, simplifying the removal

of dirt and scaly residues.


Water repellent (hydrophobic) and Dust repellent,

Provides UV Protection,

Conserves Air-Condition Load

Protects glass from corrosion (acid rain etc.) and silicon oil formation,

anti-glare,

improved visibility,

Easy application through spraying, polishing, immersion, smearing etc.,

Optically neutral (colorless, transparent),

Allows curing at room temperature.

Stable at varying temperatures,

Low Cleaning and Maintenance requirements,

It helps to retain the quality of the surface

It is ecologically beneficial & biologically safe,

It provides resistance against: Dirt, Algae, Scales etc.

AREAS OF APPLICATION: Glass facades/ Glass roofs, Window panels/glass doors, Frosted

glass, Decorative glass, Glass shower cabins, Automobile glass, all exterior glasses,

architectural glasses, Solar PV & Thermal Panels are some of the areas where this material

can be applied.


Mixing/Dilution: No mixing or dilution of the material is required. The material can

de applied directly as delivered from original packaging.

Cleaning of the Glass Surface: Prior to application it must be ensured that the glass

surface is free from all loose particles/ dust etc. If the glass surface is very dirty or

oily (Fingerprints/Stains) it must be cleaned with a cleaner (detergent

wash/acetone). If glass has been stored over a longer period of time, it must be

cleaned e.g. a glass washing line. That the glass surface is clean and completely dry,

should be ensured, if necessary, it should be wiped with little acetone.



I-CanNanoTM





in a dust free environment, if possible, in clean room conditions.

Application of coating solution: Small quantity of the material has to be applied on

the Glass Surface (Approximately about 15 ml/m2, the exact amount need to be

determined on site by a simple Roll –Off Test). Material can be applied by Spraying,

Brushing, Rolling, Dipping or Smearing using soft cloth/tissue paper/sponge. It is

recommended to apply the material in small sections for efficient coating. That the

glass surface is saturated with coating solution needs to be ensured.

Curing: The coating should be allowed to dry naturally for about 3 hours or the

coating may be dried by placing the glass at ambient temperature of 80 to 125 Deg C.

If drying process is natural and if the coating, due to different climatic conditions,

does not dry up even after about 3 hrs, then it needs to be wiped off/ polished until

it completely dries out.

Polishing: The material once applied need to be polished in circular motion using

clean & dry soft cloth/tissue paper. This can be done by polishing/ rubbing in circular

motions until it is completely rubbed off/dries out. Polishing the material at least

once is recommended in order to ensure the quality of the surface.

Test of Coating: Once coated, performance can be tested by pouring some water on

the coated panels. If coating is done properly, water should form droplets and roll-

off the glass surface and should not spread out into an uniform film.

CLEANING & MAINTENANCE OF THE COATED SURFACE: The coated surface should be

periodically cleaned with water only. Detergents or alkaline solutions should preferably be

avoided.


as per the above instructions and then subsequently recoated.

REMOVAL OF COATING: Acetone should be used for removal of coating.


I-CanNanoTM



TEST RESULTS

Test Result


Thickness of coating 530A

Light Transmission (Transmitivity) No Change

Abrasion Resistance Improved

Optical Distortion No Change

Secondary Image Separation No Change

Identification of Colors No Change

Cold Test Pass

Bake Test Pass

UV Radiation Test Pass

Humidity Test Pass

Cyclic Test Pass

Water immersion test Pass

Boil Test Pass

Wiper Test More than 330 hrs.

Temperature withstand ability Above 3000

Scratch Resistance Improved

Thermal Insulation ‘U’ value No Change in ‘U’ value

Contact angle post abrasion test No significant change

UV Protection 60% blocking of UV Rays




PACKING: 0.1/1/10/50 Liters

I-CanNanoTM



Nano Leather Coating PRODUCT DESCRIPTION: Based on Chemical Nanotechnology, the synthesized product


Matrix in a Solvent Base. NANO LEATHER COATING material, when applied on leather surface

forms a thin layer with excellent roll-Off behavior for water, simplifying the removal of dirt

and scaly residues and imparting anti-bacterial and anti-fungal behaviour.


Water repellent (hydrophobic) and Dust repellent,

Provides UV Protection,

Conserves Air-Condition Load

Easy application through spraying, polishing, immersion, smearing etc.,

Optically neutral (colorless, transparent),

Allows curing at room temperature.

Stable at varying temperatures,

Low Cleaning and Maintenance requirements,

It helps to retain the quality of the surface

It is ecologically beneficial & biologically safe,

It provides resistance against: Dirt, Algae, Scales etc.

This product provides anti-bacterial effect

AREAS OF APPLICATION: All clean and dry leather surfaces.


Mixing/Dilution: No mixing or dilution of the material is required. The material can

de applied directly as delivered from original packaging.

Cleaning of the Surface: Prior to application of the coating it must be ensured that

the surface is free from all loose particles/ dust etc. If the leather surface is very

dirty or oily (Fingerprints/Stains) it must be cleaned with a cleaner (detergent

wash/acetone). If leather has been stored over a longer period of time, it must be

cleaned. That the leather surface is clean and completely dry, should be ensured, if

necessary, it should be wiped with little nano leather cleaner.





in a dust free environment, if possible, in clean room conditions.

Application of coating solution: Small quantity of the material has to be applied on

the Leather Surface (Approximately about 15 ml/m2, the exact amount need to be

I-CanNanoTM



determined on site by a simple Roll –Off Test). Material can be applied by Spraying,

Brushing, Rolling, Dipping or Smearing using soft cloth/tissue paper/sponge. It is

recommended to apply the material in small sections for efficient coating. That the

leather surface is saturated with coating solution needs to be ensured.

Curing: The coating should be allowed to dry naturally for about 3 hours or the

coating may be dried by placing the leather at an ambient temperature of 80 to 125

Deg C. If drying process is natural and if the coating, due to different climatic

conditions, does not dry up even after about 3 hrs, then it needs to be wiped off/

polished until it completely dries out.

Polishing: The material once applied need to be polished in circular motion using

clean & dry soft cloth/tissue paper. This can be done by polishing/ rubbing in circular

motions until it is completely rubbed off/dries out. Polishing the material at least

once is recommended in order to ensure the quality of the surface.

Test of Coating: Once coated, performance can be tested by pouring some water on

the coated panels. If coating is done properly, water should form droplets and roll-

off the leather surface and should not spread out into a uniform film.

CLEANING & MAINTENANCE OF THE COATED SURFACE: The coated surface should be

periodically cleaned with water only. Detergents or alkaline solutions should preferably be

avoided.


as per the above instructions and then subsequently recoated.

REMOVAL OF COATING: Nano Leather Cleaner should be used for removal of coating.


I-CanNanoTM



TEST RESULTS

Test Result


Thickness of coating 530A Abrasion Resistance Improved Optical Distortion No Change Identification of Colors No Change Cold Test Pass Bake Test Pass UV Radiation Test Pass Humidity Test Pass Cyclic Test Pass Water immersion test Pass Boil Test Pass UV Stability 300+hrs. Temperature withstand ability Above 3000

Scratch Resistance Improved Thermal Insulation ‘U’ value Change in ‘U’ value incurred Contact angle post abrasion test No significant change UV Protection 70% blocking of UV Rays Antibacterial Effect Very high




PACKING: 1/10/50 Liter

Documents

COATING SOLUTION - I-CanNano SOLUTION.pdf · contains specially modified Functional Nano Particles that are specially linked into a Silicon Matrix in a Solvent Base. Self-organizing