Cisco/Linksys SPA Phone Base Setup for MegaPath Duet ...€¦ · IP connectivity to the SIP phone. Once the router and switch are installed, a local machine on the customer’s network

CCiissccoo//LLiinnkkssyyss SSPPAA PPhhoonnee

BBaassee SSeettuupp ffoorr MMeeggaaPPaatthh DDuueett HHoosstteedd VVooiiccee

SSeerrvviiccee

© 2010 MegaPath Inc. All rights reserved. Confidential and Proprietary 2

SSuummmmaarryy This document details the steps to obtain the basic phone setup necessary for

provisioning your Linksys or Cisco SPA phone to the MegaPath network. Once these

steps are completed, the phones will be ready to use with the Duet Hosted service.

MMiinniimmuumm RReeqquuiirreemmeennttss::

� The EdgeMarc router and Ethernet switch need to be installed and configured.

MegaPath will install and configure the EdgeMarc for all Duet Hosted customers.

MegaPath will also install and configure the Ethernet switch if MegaPath provided.

If the Ethernet switch is customer provided, the customer is be responsible for the

installation and configuration of the switch.

� The MAC Address (MAC ID) and phone number for each of the phones will need to

be provided to MegaPath. The MAC Address is located on a sticker on the bottom

of each phone. MegaPath will use the MAC Address and phone number for each

phone to provision it to the MegaPath server.

� IP address of the phone. DHCP is enabled on the EdgeMarc allowing the SIP Phones

and PCs to automatically have an IP address assigned to them. The phone IP address

can be manually looked up by depressing the "Menu" button on the phone, then

scrolling down to "Network", and then depressing the "Select" soft key button.

� IP connectivity to the SIP phone. Once the router and switch are installed, a local

machine on the customer’s network is used to pull the setup for the SIP phones.

PPhhoonnee SSeettuupp

There are two methods for setting up your Cisco or Linksys SPA phones outlined in this

document.

OOppttiioonn 11:: HHTTTTPP

Manually enter the IP address and the device name of the phone into the URL string

using the example below.

http://(Phone IP Address)/admin/resync?http://xs.voice.dsl.net/dms/(Device Name)/$MA.xml


For example:

If you have a Linksys SPA 942, with an IP address of 192.168.1.100, enter the following

in your browser:

http://192.168.1.100/admin/resync?http://xs.voice.dsl.net/dms/Linksys_SPA942/$MA.xml

RReessyynncc tthhee PPhhoonnee

Once you have entered the information for the specific phone, cut and paste the

completed URL into the browser of the local machine, and hit enter. This step will

resync the phone.

RReebboooott tthhee PPhhoonnee

You will be directed to a webpage that will display messaging about the SPA phone will

resync once the phone is rebooted, and then direct you to enter a URL to reboot the

phone so that it can be synched to the MegaPath Duet Hosted service.

Manually enter the IP address of the phone where indicated (see below). Cut and paste

the completed URL into the browser of the local machine, and hit enter.

http ://(Phone IP Address)/admin/reboot

For example:

If the IP address of the phone is 192.168.1.100, enter the following into your browser:

http://192.168.1.100/admin/reboot

The phone will now reboot and sync to the MegaPath Duet Hosted service.


OOppttiioonn 22:: HHTTTTPP iinnttoo tthhee PPhhoonnee

LLiinnkkssyyss SSPPAA PPhhoonneess

Step 1

Enter the IP address of the phone into your web browser. For example purposes we

will use the IP address: 192.168.20.12.

http://192.168.20.12

Note: If the phone prompts for a "login", enter your current login information. If you

do not know the login information, you may need to factory default your phone.

Step 2

From the default page select "Admin Login" which is located at the top right hand

corner of the web page. See arrow below.


Step 3

From the default page select "advanced” which is located at the top right hand corner.

See arrow below.


Step 4

Select the "Provisioning" tab. See arrow below.


Step 5

Enter the following into the “Profile Rule” Field (see arrow below) using the following

format: http://xs.voice.dsl.net/dms/DEVICE/$MA.xml

In this example, for a Linksys SPA 942 you would enter:

http://xs.voice.dsl.net/dms/Linksys_SPA942/$MA.xml


Step 6

Submit the changes by clicking on the "Submit All Changes" button at the bottom of the

page. See arrow below.

SStteepp 77

The phones will resync to Duet Hosted service and reboot.


CCiissccoo SSPPAA PPhhoonneess

Step 1

Enter the IP address of the phone into your web browser. For example purposes we

will use the IP address: 192.168.20.102.

http://192.168.20.102

Note: If the phone prompts for a "login", enter your current login information. If you

do not know the login information, you will need to factory default your phone.

Step 2

From the default page select "Admin Login" which is located at the top right hand

corner of the web page. See arrow below.


Step 3

From the default page select "advanced” which is located at the top right hand corner.

See arrow below.


Step 4

Select the "Provisioning" tab. See arrow below.


Step 5

Enter the following into the “Profile Rule” Field (see arrow below) using the following

format: http://xs.voice.dsl.net/dms/DEVICE/$MA.xml

In this example, for a Cisco SPA 504 you would enter:

http://xs.voice.dsl.net/dms/Cisco_SPA504/$MA.xml

If you are not sure what to enter into the DEVICE section of the URL please contact

MegaPath Technical Support.


Step 6

Submit the changes by clicking on the "Submit All Changes" button at the bottom of the

page. See arrow below.

SStteepp 77

The phones will resync to Duet Hosted service and reboot.

Documents

Cisco/Linksys SPA Phone Base Setup for MegaPath Duet ...€¦ · IP connectivity to the SIP phone. Once the router and switch are installed, a local machine on the customer’s network