Cisco CCNP 642-832 Exam - · PDF fileCisco CCNP 642-832 Exam Vendor：Cisco Exam Code: ... Switched Networks (TSHOOT) Ensurepass.com Easy Test! ... QUESTION 8 FCAPS is a network

Ensurepass.com Easy Test! Easy Pass!

Download the complete collection of Exam's Real Q&As www.ensurepass.com

Cisco CCNP 642-832 Exam

Vendor：Cisco

Exam Code: 642-832

Exam Name: Troubleshooting and Maintaining Cisco IP

Switched Networks (TSHOOT)



QUESTION 1

The following commands are issued on a Cisco Router:

Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1

Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1

Router(configuration)#exit

Router#debug ip packet 199

What will the debug output on the console show?

A. All IP packets passing through the router

B. Only IP packets with the source address of 10.1.1.1

C. All IP packets from 10.1.1.1 to 172.16.1.1

D. All IP packets between 10.1.1.1 and 172.16.1.1

Correct Answer: D

QUESTION 2

What level of logging is enabled on a Router where the following logs are screen?

%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

A. alerts

B. critical

C. errors

D. notifications

Correct Answer: D

QUESTION 3

You have the followings commands on your Cisco Router:

ip ftp username admin

ip ftp password backup

You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the

existing commands?

A. ip http username admin

B. ip http client username admin

C. ip http password backup



D. ip http client password backup

E. ip http server username admin

F. ip http server password backup

Correct Answer: BD

QUESTION 4

You have 2 NTP servers in your network - 10.1.1.1 and 10.1.1.2. You want to configurationure a

Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will

you use to configurationure the router?

A. ntp server 10.1.1.1

ntp server 10.1.1.2

B. ntp server 10.1.1.1

ntp server 10.1.1.2 primary

C. ntp server 10.1.1.1

ntp server 10.1.1.2 prefer

D. ntp server 10.1.1.1 fallback

ntp server 10.1.1.2

Correct Answer: C

QUESTION 5

The following command is issued on a Cisco Router:

Router(configuration)#logging console warnings

Which alerts will be seen on the console?

A. Warnings only

B. debugging, informational, notifications, warnings

C. warnings, errors, critical, alerts, emergencies

D. notifications, warnings, errors

E. warnings, errors, critical, alerts

Correct Answer: C

QUESTION 6

Which two of the following options are categories of Network Maintenance tasks?



A. Firefighting

B. Interrupt-driven

C. Policy-based

D. Structured

E. Foundational

Correct Answer: BD

QUESTION 7

You enabled CDP on two Cisco Routers which are connected to each other. The Line and Protocol

status for the interfaces on both routers show as UP but the routers do not see each other a CDP

neighbors. Which layer of the OSI model does the problem most likely exist?

A. Physical

B. Session

C. Application

D. Data-Link

E. Network

Correct Answer: D

QUESTION 8

FCAPS is a network maintenance model defined by ISO. It stands for which of the following?

A. Fault Management

B. Action Management

C. Configuration Management

D. Protocol Management

E. Security Management

Correct Answer: ACE

QUESTION 9

Which three management categories are contained in the FCAPS network maintenance model?

(Choose three.)

A. Config

B. Fault

C. Storage

D. Accounting



E. Redundancy

F. Telecommunications

Correct Answer: ABD

QUESTION 10

What is the result of configuring the logging console warning command?

A. Messages with a severity level of 4 and higher will be logged to all available TTY lines.

B. Only warning messages will be logged on the console.

C. Warning, error, critical, and informational messages will be logged on the console.

D. Warning, critical, alert, and emergency messages will be logged on the console.

E. The logging console warning command needs to be followed in the configuration with logging

buffered byte size to specify the message buffer size for the console.

Correct Answer: D

QUESTION 11

Refer to the shown below. What statement is correct regarding the output shown in the graphic?

% LINK-3-UPDOWN: Interface Serial0/0, change state to up

% LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

A. These two log messages will not have severity level. They are not errors but are just

informational messages.

B. The first log message is categorized as a warning message.

C. These messages regarding interface status are normal output and will always be displayed

when you exit config mode.

D. The first log message is an error message with a severity level of 3.

E. The second message would be shown if the logging console warning command had been

issued.

Correct Answer: D

QUESTION 12

Refer to the configuration statements shown in the graphic above. Which statement reflects what

the effect is of this configuration sequence?



A. These commands will generate an error message because you cannot use an access list with

any debug commands.

B. These commands will have no effect at all. The debug ip packet command will work as normal

and display info for all IP packets.

C. These commands turn on debug ip packet only for packets between hosts 10.1.1.1 and

172.16.1.1.

D. These commands will only work when you specify only one host rather than two.

Correct Answer: C

QUESTION 13

What is the result if you configure two devices with the ntp server command?

A. Nothing will happen until one of the devices is configured with the prefer parameter.

B. The NTP protocol will determine which server is most reliable and will synchronize to that

server.

C. The device with the highest priority will become the active server and the other device will

become the backup server.

D. The device with the lowest MAC address will become the active server and the other device

will become the backup server.

Correct Answer: B

QUESTION 14

A technician is troubleshooting connectivity problems between two routers that are directly

connected through a serial line. The technician notices that the serial line is up, but cannot see any

neighbors displayed in the output of the show cdp neighbors command. In which OSI layer is the

problem most likely occurring?

A. physical

B. data link

C. network

D. transport

E. application

Correct Answer: B



QUESTION 15

What are two approaches to maintaining a network?(Choose two)

A. PPDIOO

B. structured

C. bottoms up

D. interrupt-driven

Correct Answer: BD

QUESTION 16

FCAPS is a network maintenance model defined by ISO. FCAPS stands for:

Correct Answer:

QUESTION 17

There are many Network Maintenance models. Match the model names on the left to the options

on the right:



Correct Answer:

QUESTION 18

Match the items on the left to their purpose on the right:

Correct Answer:



QUESTION 19

Ticket 1: Switch Port Trunk

Scenario: The implementation group has been using the test bed to do a 'proof-of-concept' that

requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several

changes to the network addressing, routing schemes, DHCP services, layer 2 connectivity, FHRP

services, and, device security, a trouble ticket has been opened indicating that Client 1 cannot ping

the 209.65.200.241 address.



Trouble Ticket Statement

Client 1 and Client 2 are getting a 169.x.x.x IP address and are not able to ping DSW1 or the FTP

Server. They are able to ping each other.

Configuration on ASW1

Interface PortChannel13 switchport mode trunk

switchport trunk allowed vlan 1-9

!

Interface PortChannel23 switchport mode trunk


!

Interface FastEthernet1/0/1 switchport mode access switchport access vlan 10

!

Interface FastEthernet1/0/2 switchport mode access switchport access vlan 10

!

On which device is the fault condition located?

A. ASW1

B. DSW1

C. Client 1



D. FTP Server

E. ASW2

F. DSW2

Correct Answer: A

QUESTION 20






the 209.65.200.241 address.





The Fault Condition is related to which technology?



A. NTP

B. Switch to Switch Connectivity

C. Access Vlans

D. Port Security

E. VLAN ACL / Port ACL

F. Switch Virtual Interface

Correct Answer: B

QUESTION 21






the 209.65.200.241 address.







Interface PortChannel13

switchport mode trunk


!

Interface PortChannel23

switchport mode trunk


!

Interface FastEthernet1/0/1

switchport mode access

switchport access vlan 10

!




!



What is the solution of the fault condition?

A. Change the VLAN assignment on fa1/0/1 and fa1/0/2 on ASW1 to VLAN 1

B. Change the IP Address of VLAN 10 on DSW1

C. Issue switchport trunk allowed vlan 10,200 on interface portchannel13 and portchannel23 on

ASW1

D. Issue switchport trunk allowed vlan none on interface portchannel13 and portchanngel23 on

ASW1

Correct Answer: C

QUESTION 22

Ticket 2: Access VLAN





the 209.65.200.241 address.










!





A. DSW1

B. ASW1

C. Client 1

D. FTP Server

E. DSW2

F. ASW2



Correct Answer: B

QUESTION 23






the 209.65.200.241 address.



Use the supported commands to isolate the cause of this fault and answer the following questions.


The fault condition is related to switch technology?

A. NTP

B. Switch-to-Switch Connectivity

C. Loop Prevention



D. Access Vlans

E. VLAN ACL Port ACL

F. Switch Virtual Interface

G. Port Security

Correct Answer: D

QUESTION 24






the 209.65.200.241 address.





What is the solution to the fault condition?

A. In Configuration mode, using the interface range Fastethernet 1/0/1 - 2, then switchport mode

access vlan 10 command.

B. In Configuration mode, using the interface rante Fastethernet 1/0/1 - 2, then switchport access

mode vlan 10 command.



C. In Configuration mode, using the interface range Fastethernet 1/0/1 - 2, then switchport vlan

10 access command.

D. In Configuration mode, using the interface range Fastethernet 1/0/1 - 2, then switchport access

vlan 10 command.

Correct Answer: D

QUESTION 25

Ticket 3: OSPF Authentication





the 209.65.200.241 address.




Configuration on R1 and R2

On which is the fault condition located?



A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Correct Answer: A

QUESTION 26






the 209.65.200.241 address.




Configuration on R1 and R2

The fault condition is related to which technology?



A. BGP

B. NTP

C. IP NAT

D. IPv4 OSPF Routing

E. IPv4 OSPF Redistribution

F. IPv6 OSPF Routing

G. IPv4 layer 3 security

Correct Answer: D

QUESTION 27






the 209.65.200.241 address.



Trouble Ticket Statement:

Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not

have any OSPF neighbors or any OSPF routes

Configuration on R1:

router ospf 1

log-adjacency-changes

network 10.1.1.0 0.0.0.3 area 12

default-information originate always

!

interfaceSerial0/0/0/0.12 point-to-point

ip address 10.1.1.1 255.255.255.252

ip nat inside

ip ospf message-digest-key 1 md5 TSHOOT

Configuration on R2:

router ospf 1

log-adjacency-changes

network 10.1.1.0 0.0.0.3 area 12

!



interfaceSerial0/0/0/0.12 point-to-point

ip address 10.1.1.2 255.255.255.252

ip ospf authentication message-digest



A. ip ospf authentication message-digest command has to be added on S0/0/0/0.12

B. ip ospf authentication message-digest command has to be added under the OSPF routing

process

C. A static route to 10.1.1.4 must be added on R1

D. ip nat outside must be added on S0/0/0/0.12

E. ip ospf authentication command has to be added on router ospf 1 on R1

F. ip ospf authentication command has to be added on router ospf 1 on R2

Correct Answer: A

QUESTION 28

Ticket 4: BGP Neighbor





the 209.65.200.241 address.




Configuration on R1



On which is the fault condition located?

A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

H. ASW2

Correct Answer: A

QUESTION 29






the 209.65.200.241 address.






Client 1 is able to ping 209.65.200.226 but not the Web Server at 209.65.200.241. Initial

troubleshooting shows and R1 does not have any BGP routes. R1 also does not show any active

BGP neighbor

Configuration on R1

router bgp 65001

no synchronization

bgp log-neighbor-changes

network 209.65.200.224 mask 255.255.255.252

neighbor 209.56.200.226 remote-as 65002

no auto-summary

R1#sh bgp ipv4 unicast neighbors

BGP neighbor is 209.56.200.226, remote AS 65002, external link

BGP version 4, remote router ID 0.0.0.0

BGP state = Idle

Last read 00:00:20, last write 00:00:20, hold time is 180, keepalive interval is 60 seconds

Message statistics:

InQ depth is 0

OutQ depth is 0

Sent Rcvd

Opens: 0 0

Notifications: 0 0

Updates: 0 0

Keepalives: 0 0

Route Refresh: 0 0

Total: 0 0

Default minimum time between advertisement runs is 30 seconds

For address family: IPv4 Unicast

BGP table version 2, neighbor version 0/0

Output queue size: 0

Index 1, Offset 0, Mask 0x2

1 update-group member

Sent Rcvd

Prefix activity: ---- ----

Prefixes Current: 0 0

Prefixes Total: 0 0

Implicit Withdraw: 0 0

Explicit Withdraw: 0 0

Used as bestpath: n/a 0

Used as multipath: n/a 0



Outbound Inbound

Local Policy Denied Prefixes: -------- -------

Total: 0 0

Number of NLRIs in the update sent: max 0, min 0

Connections established 0; dropped 0

Last reset never

External BGP neighbor not directly connected.

No active TCP connection


A. EIGRP

B. HSRP

C. BGP

D. OSPF

E. OSPFv3

F. RIP

Correct Answer: C

QUESTION 30






the 209.65.200.241 address.




Configuration on R1




A. Under the BGP process, enter the bgp redistribute-internal command.

B. Under the BGP process, bgp confederation identifier 65001 command.

C. Delete the current BGP process and reenter all of the commands using 65002 as the AS number.

D. Under the BGP process, delete the neighbor 209.56.200.226 remote-as 65002 command and

enter the neighbor 209.65.200.226 remote-as 65002 command.

Correct Answer: D

QUESTION 31

Ticket 5: NAT ACL





the 209.65.200.241 address.






Client 1 and Client 2 are not able to reach the WebServer at 209.65.200.241. Initial troubleshooting

shows that DSW1, DSW2 and all the routers are able to reach the WebServer

Configuration on R1

ip nat inside source list nat_pool interface Serial0/0/0/1 overload !

ip access-list standard nat_pool

permit 10.1.0.0

!

interface Serial0/0/0/1

ip address 209.65.200.224 255.255.255.252

ip nat outside

!

interfaceSerial0/0/0/0.12

ip address 10.1.1.1 255.255.255.252

ip nat inside


ip ospd authentication message-digest


A. R1

B. DSW1

C. R4

D. R2

E. R3

F. DSW2

Correct Answer: A

QUESTION 32

Ticket 5: NAT ACL





the 209.65.200.241 address.








Configuration on R1

ip nat inside source list nat_pool interface Serial0/0/0/1 overload !


permit 10.1.0.0

!


ip address 209.65.200.224 255.255.255.252

ip nat outside

!


ip address 10.1.1.1 255.255.255.252

ip nat inside




A. EIGRP

B. HSRP

C. BGP

D. NAT

E. OSPF

F. OSPFv3

Correct Answer: D

QUESTION 33

Ticket 5: NAT ACL





the 209.65.200.241 address.








Configuration on R1

ip nat inside source list nat_pool interface Serial0/0/0/1 overload

!


permit 10.1.0.0

!


ip address 209.65.200.224 255.255.255.252

ip nat outside

!


ip address 10.1.1.1 255.255.255.252

ip nat inside




A. Add permit 10.2.0.0 statement in nat_pool access-list

B. Remove permit 10.1.0.0 statement from nat_pool access-list

C. Change ip nat inside source list nat_pool interface Serial0/0/0/1 overload to ip nat inside source

list nat_pool interface Serial0/0/0/0.12 overload

D. Change ip nat outside statement under Serial0/0/0/1 configuration to ip nat inside

Correct Answer: A

QUESTION 34

Ticket 6: ACL





the 209.65.200.241 address.






Configuration on R1


A. R1

B. R2

C. R3

D. R4

E. DSW1

F. DSW2

G. ASW1

Correct Answer: A

QUESTION 35

Ticket 6: ACL





the 209.65.200.241 address.






Client 1 is not able to reach the WebServer at 209.65.200.241. Initial troubleshooting shows that

R1 is also not able to reach the WebServer. R1 also does not have any active BGP neighbor.

Config on R1

router bgp 65001

no synchronization


network 209.65.200.224 mask 255.255.255.252


no auto-summary

!

access-list 30 permit host 209.65.200.241

access-list 30 deny 10.1.0.0 0.0.255.255

access-list 30 deny 10.2.0.0 0.0.255.255

!


ip address 209.65.200.224 255.255.255.252

ip nat outside

ip access-group 30 in


A. R1

B. DSW1

C. R4

D. R2

E. DSW2

F. R3

Correct Answer: A

QUESTION 36

Ticket 6: ACL





the 209.65.200.241 address.








Config on R1

router bgp 65001

no synchronization


network 209.65.200.224 mask 255.255.255.252


no auto-summary

!


access-list 30 deny 10.1.0.0 0.0.255.255

access-list 30 deny 10.2.0.0 0.0.255.255

!


ip address 209.65.200.224 255.255.255.252

ip nat outside



A. IP Access

B. IP NAT

C. BGP

D. IP Access List

E. OSPF

F. Add permit statement for 209.65.200.224/30 network in access list 30

Correct Answer: D

QUESTION 37

Ticket 6: ACL





the 209.65.200.241 address.








Config on R1

router bgp 65001

no synchronization


network 209.65.200.224 mask 255.255.255.252


no auto-summary

!


access-list 30 deny 10.1.0.0 0.0.255.255

access-list 30 deny 10.2.0.0 0.0.255.255

!


ip address 209.65.200.224 255.255.255.252

ip nat outside



A. Add permit statement for 209.65.200.224/30 network in access list 30

B. Remove Deny Statements from access-list 30

C. Change neighbor 209.65.200.226 remote-as 65002 statement to neighbor 209.65.200.226

remote-as 65001

D. Use extended access-list instead of standard access-list

Correct Answer: A

QUESTION 38

Ticket 7: Port Security





the 209.65.200.241 address.






Client one is getting a 169.x.x.x IP address and is not able to ping Client 2 or DSW1. Inital

troubleshooting shows that port Fa1/0/1 on ASW1 is in errdisable state.




switchport port-security

switchport port-security mac-address 0000.0000.0001


A. DSW1

B. ASW1

C. Client 1

D. FTP Server

E. ASW2

F. DSW2

Correct Answer: B

QUESTION 39






the 209.65.200.241 address.











CertKiller.com




A. VLAN Access Map

B. InterVLAN communication

C. DHCP

D. Port Security

E. ASW2

F. DSW1

Correct Answer: D

QUESTION 40






the 209.65.200.241 address.














A. Configurationure Static IP Address on Client 1


C. Issue shutdown command followed by no shutdown command on port fa1/0/1 on ASW1

D. Issue no switchport port-security mac-address 0000.0000.0001 command followed by

shutdown and no shutdown command on port fa1/0/1 on ASW1

E. Issue no switchport port-security mac-address 0000.0000.0001 command on port fa1/0/1 on

ASW1

Correct Answer: D

QUESTION 41

Ticket 8: Redistribution of EIGRP to OSPF





the 209.65.200.241 address.






Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the

Fa0/1 interface of R4 but not the s0/0/0/0.34 interface.

Configuration on DSW1

router eigrp 10

network 10.1.4.4 0.0.0.0

network 10.2.1.1 0.0.0.0

network 10.2.4.13 0.0.0.0

no auto-summary


router eigrp 10

network 10.1.4.8 0.0.0.0

network 10.2.2.1 0.0.0.0

network 10.2.4.14 0.0.0.0

no auto-summary

Configuration on R4

router eigrp 10

network 10.1.4.5 0.0.0.0

no auto-summary

redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF

!

router ospf 1

network 10.1.1.8 0.0.0.0 area 34

redistribute eigrp 10 subnets

!

route-map EIGRP->OSPF

match ip address 1

!

access-list 1 permit 10.0.0.0 0.255.255.255



A. DSW1

B. DSW2

C. Client 1

D. Client 2

E. R4

Correct Answer: E



QUESTION 42






the 209.65.200.241 address.







router eigrp 10

network 10.1.4.4 0.0.0.0

network 10.2.1.1 0.0.0.0

network 10.2.4.13 0.0.0.0

no auto-summary


router eigrp 10

network 10.1.4.8 0.0.0.0

network 10.2.2.1 0.0.0.0

network 10.2.4.14 0.0.0.0

no auto-summary

Configuration on R4



router eigrp 10

network 10.1.4.5 0.0.0.0

no auto-summary

redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF !

router ospf 1

network 10.1.1.8 0.0.0.0 area 34

redistribute eigrp 10 subnets

!

route-map EIGRP->OSPF

match ip address 1

!




A. EIGRP

B. Route Redistribution

C. OSPF

D. IP Addressing

E. HSRP

F. BGP

Correct Answer: B

QUESTION 43






the 209.65.200.241 address.




Configuration on R4




A. Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_to_EIGRP command

and enter the redistribute ospf 1 route-map OSPF->EIGRP command.

B. Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_to_EIGRP command

and enter the redistribute ospf 6 metric route-map OSPF->EIGRP command.

C. Under the EIGRP process, delete the redistribute EIGRP 10 subnets route-map EIGRP->OSPF

command and enter the redistribute eigrp 10 subnets route-map OSPF->EIGRP command.

D. Under the EIGRP process, delete the redistribute EIGRP 10 subnets route-map EIGRP->OSPF

command and enter the redistribute eigrp 10 subnets route-map EIGRP->OSPF command.

Correct Answer: A



QUESTION 44

Ticket 9: EIGRP AS number





the 209.65.200.241 address.







router eigrp 10

network 10.1.4.4 0.0.0.0

network 10.2.1.1 0.0.0.0

network 10.2.4.13 0.0.0.0

no auto-summary


router eigrp 10

network 10.1.4.8 0.0.0.0

network 10.2.2.1 0.0.0.0

network 10.2.4.14 0.0.0.0

no auto-summary

Configuration on R4



router eigrp 1

network 10.1.4.5 0.0.0.0

no auto-summary

redistribute ospf 1


A. DSW1

B. DSW2

C. Client 1

D. R4

E. R2

F. R1

G. R3

Correct Answer: D

QUESTION 45






the 209.65.200.241 address.









router eigrp 10

network 10.1.4.4 0.0.0.0

network 10.2.1.1 0.0.0.0

network 10.2.4.13 0.0.0.0

no auto-summary


router eigrp 10

network 10.1.4.8 0.0.0.0

network 10.2.2.1 0.0.0.0

network 10.2.4.14 0.0.0.0

no auto-summary

Configuration on R4

router eigrp 1

network 10.1.4.5 0.0.0.0

no auto-summary

redistribute ospf 1


A. EIGRP


C. OSPF

D. Switch to Switch Connectivity

E. BGP

F. HSRP

Correct Answer: A

QUESTION 46








the 209.65.200.241 address.




Configuration on R4


A. Disable auto summary on the EIGRP process.

B. Enable EIGRP on the FastEthernet0/0 and FastEthernet0/1 interface using the no passive-

interface command.

C. Change the AS number on the EIGRP routing process from 1 to 10 to much the AS number

used on DSW1 and DSW2.

D. Under the EIGRP process, delete the network 10.1.4.0 0.0.0.255 command and enter the

network 10.1.4.4 0.0.0.252 and 10.1.4.8 0.0.0.252 commands.

Correct Answer: C

QUESTION 47

Ticket 10: VLAN Access Map





the 209.65.200.241 address.






Client 1 is getting an IP address from the DHCP server but is not able to ping DSW1 or the FTP

Server


vlan access-map test1 10

drop

match ip address 10

!

vlan filter test1 vlan-list 10

!

ip access-list standard 10

permit 10.2.0.0 0.0.255.255

!

Interface VLAN10

ip address 10.2.1.1 255.255.255.0

!


A. R4

B. DSW1

C. Client 1

D. FTP Server

E. DSW2

F. R1

Correct Answer: B

QUESTION 48






the 209.65.200.241 address.







DSW1


action drop

match ip address 10


action drop

match ip address 20


action foward

match ip address 30


action foward

!


vlan internal allocation policy asdending

!

access-list 10 permit 10.2.1.3




A. NTP

B. IP DHCP Helper

C. IPv4 EIGRP Routing

D. IPv6 RIP Routing

E. IPv4 layer 3 security

F. Switch-to-Switch Connectivity

G. Loop Prevention

H. Access Vlans

I. Port Security

J. VLAN ACL / Port ACL

K. Switch Virtual Interface

Correct Answer: J

QUESTION 49








the 209.65.200.241 address.





Server



drop

match ip address 10

!


!


permit 10.2.0.0 0.0.255.255

!

Interface VLAN10

ip address 10.2.1.1 255.255.255.0

!


A. VLAN Access Map




C. DHCP

D. IP Access List

E. VLAN Map

Correct Answer: A

QUESTION 50






the 209.65.200.241 address.





Server



drop

match ip address 10

!


!


permit 10.2.0.0 0.0.255.255

!

Interface VLAN10

ip address 10.2.1.1 255.255.255.0

!


A. Configurationure Static IP Address on Client 1




C. Add Permit any statement to access-list 10

D. Remove VLAN filter test1 from DSW1

Correct Answer: D

QUESTION 51






the 209.65.200.241 address.





DSW1


action drop

match ip address 10


action drop

match ip address 20


action foward

match ip address 30


action foward

!


vlan internal allocation policy asdending

!







A. Under the global configuration mode enter no access-list 10 command.

B. Under the global configuration mode enter no access-map vlan 10 command.

C. Under the global configuration mode enter no vlan access-map test1 10 command.

D. Under the global configuration mode enter no vlan filter test1 vlan-list 10 command.

Correct Answer: C

QUESTION 52

Ticket 11: IPv6 OSPF





the 209.65.200.241 address.

The network setup for this trouble ticket is shown in exhibit.


DSW1 and R4 cannot ping R2's loopback or R2's s0/0/0/0.12 IPv6 address. Initial troubleshooting



shows and R2 is not an OSPFv3 neighbor on R3.

Configuration on R2

ipv6 unicast-routing

!

ipv6 router ospf 6

router-id 2.2.2.2

!

interface s0/0/0/0.23

ipv6 address 2026::1:1/122

Configuration on R3


!

ipv6 router ospf 6

router-id 3.3.3.3

!


ipv6 address 2026::1:2/122

ipv6 ospf 6 area 0


A. DSW1

B. DSW2

C. R2

D. R3

E. R1

F. R4

Correct Answer: C

QUESTION 53








the 209.65.200.241 address.





Configuration on R2


!

ipv6 router ospf 6

router-id 2.2.2.2

!


ipv6 address 2026::1:1/122

Configuration on R3




!

ipv6 router ospf 6

router-id 3.3.3.3

!


ipv6 address 2026::1:2/122

ipv6 ospf 6 area 0


A. IPv6 Addressing

B. Route Redistribution

C. OSPFv3

D. RIPng

E. BGP

Correct Answer: C

QUESTION 54






the 209.65.200.241 address.







Configuration on R2


!

ipv6 router ospf 6

router-id 2.2.2.2

!


ipv6 address 2026::1:1/122

Configuration on R3


!

ipv6 router ospf 6

router-id 3.3.3.3

!




ipv6 address 2026::1:2/122

ipv6 ospf 6 area 0


A. Add ipv6 ospf 6 area 0 under s0/0/0/0.23 on R2

B. Add ipv6 ospf 6 area 6 under s0/0/0/0.23 on R2

C. Remove IPv6 address from s0/0/0/0.23 on R2

D. Enable IPv6 routing on s0/0/0/0.23 on R2

Correct Answer: A

QUESTION 55

Ticket 12: HSRP Issue





the 209.65.200.241 address.




HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be

active router but it never becomes active even though the HSRP communication between DSW1

and DSW2 is working.


track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2

!


!

interface Vlan10

ip address 10.2.1.1 255.255.255.0

standby 10 ip 10.2.1.254

standby 10 priority 200

standby 10 preempt

standby 10 track 1 decrement 60

Configuration on R4

interface loopback0

ip address 10.2.21.128 255.255.255.0




A. R4

B. DSW2

C. DSW1

D. R3

E. R2

F. R1

Correct Answer: C

QUESTION 56






the 209.65.200.241 address









!


!

interface Vlan10

ip address 10.2.1.1 255.255.255.0

standby 10 ip 10.2.1.254


standby 10 preempt


Configuration on R4

interface loopback0

ip address 10.2.21.128 255.255.255.0



Fault Condition is related to which technology?

A. GLBP

B. HSRP

C. OSPF

D. Switch to Switch Connectivity

E. VRRP

F. EIGRP

Correct Answer: B

QUESTION 57






the 209.65.200.241 address.









!


!

interface Vlan10

ip address 10.2.1.1 255.255.255.0

standby 10 ip 10.2.1.254


standby 10 preempt


Configuration on R4

interface loopback0

ip address 10.2.21.128 255.255.255.0



What is the solution of fault condition?

A. Change standby priority to 140

B. Change standby priority to 260

C. Change standby 10 track 1 decrement 60 to standby 10 track 10 decrement 60

D. Change standby 10 track 1 decrement 60 to standby 10 track 1 decrement 100

E. Change standby 10 track 1 decrement 60 to standby 10 track 10 decrement 100

F. Change standby 10 track 1 decrement 60 to standby 10 track 1 decrement 60

Correct Answer: C

QUESTION 58

Ticket 13: DHCP Issue Topology Overview





the 209.65.200.241 address.

Client should have IP 10.2.1.3

EIGRP 100 is running between switch DSW1 & DSW2

OSPF (Process ID 1) is running between R1, R2, R3, R4

Network of OSPF is redistributed in EIGRP

BGP 65001 is configured on R1 with Webserver cloud AS 65002

HSRP is running between DSW1 & DSW2 switches



Question:






services, and, device security, a trouble ticket has been opened indicating DSWA will not become

the active outer for HSRP group 10.

Configuration on R4 was:

!

ip dhcp exclude 10.2.1.1-10.2.1.253

!


A. R4

B. DSW1

C. DSW2

D. ASW1

E. ASW2

F. Client 1

G. Client 2

Correct Answer: A

QUESTION 59






the 209.65.200.241 address.











Question:







!

ip dhcp exclude 10.2.1.1-10.2.1.253

!




A. NTP

B. IP DHCP Server

C. IPv4 EIGRP Routing

D. IPv6 RIP Routing

E. IPv4 layer 3 security

F. Switch-to-Switch Connectivity

G. Loop Prevention

H. Access Vlans

I. Port Security

J. VLAN ACL / Port ACL

K. Switch Virtual Interface

Correct Answer: B

QUESTION 60






the 209.65.200.241 address.









Question:









!

ip dhcp exclude 10.2.1.1-10.2.1.253

!


A. on DSW1 delete ip dhcp exclude 10.2.1.1-10.2.1.253 and apply ip dhcp-excluded 10.2.1.1-

10.2.1.2

B. on DSW2 delete ip dhcp exclude 10.2.1.1-10.2.1.253 and apply ip dhcp-excluded 10.2.1.1-

10.2.1.2

C. on R4 delete ip dhcp exclude 10.2.1.1-10.2.1.253 and apply ip dhcp-excluded 10.2.1.1-10.2.1.2

D. on R4 delete ip dhcp exclude 10.2.1.1-10.2.1.253 and apply ip dhcp-excluded 10.2.1.1-

10.2.1.10

Correct Answer: C

QUESTION 61

Ticket 14: EIGRP Passive Interface





the 209.65.200.241 address.









router eigrp 10

network 10.1.4.4 0.0.0.0

network 10.2.1.1 0.0.0.0

network 10.2.4.13 0.0.0.0

no auto-summary


router eigrp 10

network 10.1.4.8 0.0.0.0

network 10.2.2.1 0.0.0.0

network 10.2.4.14 0.0.0.0

no auto-summary

Configuration on R4

router eigrp 10

passive-interface default

redistribute ospf 1 route-map OSPF->EIGRP

network 10.1.4.4 0.0.0.3

network 10.1.4.8 0.0.0.3

default-metric 10000 100 255 1 10000

no auto-summary


A. DSW1

B. DSW2

C. Client 1

D. R1

E. R2

F. R3

G. R4

Correct Answer: G

QUESTION 62



Ticket 14: EIGRP Passive Interface





the 209.65.200.241 address.

Ensurepass.com Members Features:

1. Verified Answers researched by industry experts.

2. Q&As are downloadable in PDF and VCE format.

3. 98% success Guarantee and Money Back Guarantee.

4. Free updates for 180 Days.

View list of All Exam provided:

http://www.ensurepass.com/certfications?index=A

To purchase Lifetime Full Access Membership click here:

http://www.ensurepass.com/user/register

Valid Discount Code for 2014: SFOH-FZA0-7Q2S

To purchase the HOT Exams:

Cisco CompTIA Oracle VMWare IBM

100-101 640-554 220-801 LX0-101 1Z0-051 VCAD510 C2170-011

200-120 640-802 220-802 N10-005 1Z0-052 VCP510 C2180-319

300-206 640-816 BR0-002 SG0-001 1Z0-053 VCP550 C4030-670

300-207 640-822 CAS-001 SG1-001 1Z0-060 VCAC510 C4040-221

300-208 640-864 CLO-001 SK0-002 1Z0-474 VCP5-DCV RedHat

350-018 642-467 ISS-001 SK0-003 1Z0-482 VCP510PSE EX200

352-001 642-813 JK0-010 SY0-101 1Z0-485 EX300

400-101 642-902 JK0-801 SY0-301 1Z0-580

640-461 700-302 1Z0-820

http://www.ensurepass.com/certfications?index=A

http://www.ensurepass.com/user/register

http://www.ensurepass.com/cisco.html

http://www.ensurepass.com/comptia.html

http://www.ensurepass.com/oracle.html

http://www.ensurepass.com/VMWare.html

http://www.ensurepass.com/ibm.html

http://www.ensurepass.com/100-101.html



http://www.ensurepass.com/lx0-101.html

http://www.ensurepass.com/1z0-051.html

http://www.ensurepass.com/VCAD510.html

http://www.ensurepass.com/C2170-011.html




http://www.ensurepass.com/n10-005.html


http://www.ensurepass.com/VCP510.html




http://www.ensurepass.com/BR0-002.html

http://www.ensurepass.com/sg0-001.html


http://www.ensurepass.com/VCP550.html




http://www.ensurepass.com/CAS-001.html

http://www.ensurepass.com/sg1-001.html


http://www.ensurepass.com/VCAC510.html




http://www.ensurepass.com/CLO-001.html

http://www.ensurepass.com/sk0-002.html


http://www.ensurepass.com/VCP5-DCV.html

http://www.ensurepass.com/redhat.html



http://www.ensurepass.com/ISS-001.html

http://www.ensurepass.com/sk0-003.html


http://www.ensurepass.com/VCP510PSE.html

http://www.ensurepass.com/EX200.html



http://www.ensurepass.com/JK0-010.html

http://www.ensurepass.com/sy0-101.html


http://www.ensurepass.com/EX300.html



http://www.ensurepass.com/JK0-801.html

http://www.ensurepass.com/sy0-301.html





http://www.ensurepass.com/apple.html

http://www.ensurepass.com/citrix.html

http://www.ensurepass.com/comptia.html

http://www.ensurepass.com/microsoft.html

http://www.ensurepass.com/oracle.html

http://www.ensurepass.com/cisco.html

Documents

Cisco CCNP 642-832 Exam - · PDF fileCisco CCNP 642-832 Exam Vendor：Cisco Exam Code: ... Switched Networks (TSHOOT) Ensurepass.com Easy Test! ... QUESTION 8 FCAPS is a network