Chemco Marine Brochure

8/6/2019 Chemco Marine Brochure

1/10


2/10


3/10


4/10


5/10


6/10


7/10

PRODUCT FEATURES Moisture tolerant: Surpasses any so called

moisture tolerant material, hence it is calledWet-tolerant. The product can be applied in anyhumidity. High humidity, rain or water has no

detrimental affect on coating performance.

Solvent-free: 100% solid, no ventilation,de-humidification or heating required. No fire

hazard during application or storage.

Cost effective: Substantial cost savings areachieved due to alternative surface preparation,

lack of supportive equipment (de-humidifiers,

ventilators, heaters etc) and quick back-in service

time (tank is operational within 6 - 12 hours after

application).

Can cure underwater - reducing back-in service

times.

Unlimited over-coating: ultimate product for start/stopmaintenance projects.

Compatible: Coating compatible with virtually everycoal-tar epoxy coatings or other traditional ballast tank

paints.

Compatible with all shop primers. Long-term protection: Glassflakes technology

ensures long-term performance, life expectancy up to

25 years (with factory guarantee), far exceeding

IMO/PSPC latest requirements. Adhesion test result

on wet substrates far exceed the industry norms (for

dry grit blasted) attaining over 1300psi before

cohesive failure.

Reduces the risk of MIC (Microbiological InducedCorrosion) and SRB (Sulphate Reducing Bacteria)

as it does not contain the nutrients solvent-based

coatings.

Excellent chemical resistance.

RA 500MEpoxy Solvent-free Systems

Solvent-free, Wet-tolerant, Glassflake Epoxy

APPLICATION Tanks - ballast, oil cargo, fresh drinking water

and dry cargo (FDA approved), grey water.

Void spaces, cofferdams.

Superstructures, pipes.

Decks and internal floors. New builds.

Rev: Apr 2010

APPROVALS Lloyds certificate (salt water ballast tank).

FDA (use with fresh drinking water, use in

transporting and holding all non-alcoholic food).


8/10

DISCLAIMER The information contained herein is to the best of our knowledge accurate and current and is given in good faith without warranty. Users aredeemed to have satisfied themselves independently as to the suitability of our products for their particular purpose. In no event shall Chemco

International be liable for consequent or incidental damages.

East Shawhead Industrial Estate

Coatbridge

ML5 4XD, Scotland UK

Tel: +44 (0) 1236 606060

Fax: +44 (0) 1236 606070

Email: [email protected]

Web: www.chemcoint.com

APPLICATION DATAMethod: Airless spray, roller, brush or trowel.

Thinner: T5 if required (maximum 5%).

Cleaner: S11A

Recoating interval:Minimum: 4 - 6 hrs (touch dry).

Maximum: Unlimited.

Pot life: 45 - 75 minutes (depending on temperature).

Cure: 24 - 72 hrs (depending on temperature and other environmental conditions).

APPLICATIONConstitutes: Two pack epoxy system consisting of base resin and hardener.

Airless spray:Pump: Minimum 45:1 ratio (preferably 63:1), large volume delivery is essential

Tip: (23 - 31 thou. Ideal 27 thou.) 60angle, heavy duty reversible.

Brush or roller: For inaccessible or awkward areas or when spray application is not required or feasible.

SURFACE PREPARATIONAbrasive blast: Min. SA 2

Water-jetting: Min. WJ-2

Mechanical: Min. ST3

LIMITATIONSPot life: Vigilant care and attention to pot life is required during application. If gelling has started, do not

apply.

Airless spraying: Preferably keep the material at room temperature when airless spraying.

Environmental conditions: There are no humidity, dew point restrictions.

Safety precautions:

It is the policy of CHEMCO INTERNATIONAL to ensure that its products are handled and applied

by professionally approved and skilled applicators. Application shall be carried out in accordance

with instructions contained in this data sheet and referenced to CHEMCO INTERNATIONAL

TECHNICAL SPECIFICATION MANUAL. CHEMCO INTERNATIONAL management are intent onensuring all work is carried out in accordance with company HEALTH & SAFETY procedures and

all materials are handled with due care to COSHH regulations and instructions.

Storage: Store in cool, dry conditions (not less than 4C or above 20C). Keep away from direct heat

source and sunlight. When not using the material, always replace the lid on the container.

Shelf life: At least 24 months when stored in sealed containers at temperatures of not less than 4C or

above 20C. At temperatures above, refer to manufacturer for advice.

Pack sizes: 5 and 20 kgs

Temperature resistance: Maximum 60C (immersed).

Theoretical coverage:

3.1m/kg@ 250 microns.

1.5m/kg@ 500 microns.

(Allow for application losses, surface irregularities, etc).

Typical thickness range: 200 - 600 microns per coat.

Mix ratio:Mix part A (resin RA 500M) and part B (hardener HF 500M)

in proportionate weights as supplied.

Cure: Catalyst induced cross-linking polymerisation.

Volume solids: 100%

Colour: Standard light grey (other colours available on request).

PRODUCT DATA


9/10

PRODUCT FEATURES Surface tolerant: Surpasses any so called

surface tolerant material, hence it is calledRust-Tolerant. Ideal for poorly and hand preparedsurfaces (ST2 or WJ-4).

Moisture tolerant: Surpasses any so calledmoisture tolerant material, hence it is calledWet-Tolerant. The product can be applied in anyhumidity and on really wet surfaces.

Solvent-free: 100% solid, no ventilation,de-humidification or heating required. No fire

hazard during application or storage.

Any surface preparation method: Choose themost convenient/cost effective system, e.g.

grit-blast, wet-blast, HP water jetting (500-800

bar), UHP or mechanical.

Compatible: Coating compatible with virtuallyevery coal-tar epoxy coatings or other traditional

ballast tank paints.

Compatible with all shop primers. Cost Effective: Substantial cost savings are

achieved due to minimal surface preparation,

lack of supportive equipment (de-humidifiers,

ventilators, heaters etc) and quick back-in

service time (tank is operational within

6 - 12 hours after application).

Unlimited over-coating: Ultimate product forstart/stop maintenance projects.

Can cure underwater - reducing back-in servicetimes.

Available in tropical grade RS 500P-TG

RS 500PEpoxy Solvent-free Systems

Unique Solvent-free, Wet-tolerant, Rust-tolerant Epoxy Primer/Finish

Rev: June 2010

APPLICATION Tanks - ballast, oil cargo, fresh drinking water

and dry cargo, grey water.

Void spaces, cofferdams.

Superstructures, pipes.

Decks and internal floors. New builds.

APPROVALS Lloyds certificate (salt water ballast tank).


10/10

DISCLAIMER The information contained herein is to the best of our knowledge accurate and current and is given in good faith without warranty. Users aredeemed to have satisfied themselves independently as to the suitability of our products for their particular purpose. In no event shall Chemco

International be liable for consequent or incidental damages.

APPLICATION DATAMethod: Airless spray, roller or brush.

Thinner: T5 (if required).

Cleaner: S11A

Recoating interval:Minimum: Touch dry.

Maximum: Unlimited.

RS 500P 15C 30C RS 500P-TG 15C 30CPot life (minutes)*: 65 30 140 65

APPLICATIONConstitutes: Two pack epoxy system consisting of base resin and hardener.

Airless spray:Pump: Minimum 45:1 ratio (preferably 63:1), large volume delivery is essential

Tip: (17 - 19 thou.) 60angle, heavy duty reversible.

Brush or roller: For inaccessible or awkward areas or when spray application is not required or feasible.SURFACE PREPARATIONAbrasive blast: Min. SA 1

Water-jetting: Min. WJ-4

Mechanical: Min. ST2

LIMITATIONSPot life: Vigilant care and attention to pot life is required during application. If gelling has started, do not

apply.

Environmental conditions: There is no humidity, dew point restrictions.

Safety precautions:

It is the policy of CHEMCO INTERNATIONAL to ensure that its products are handled and applied

by professionally approved and skilled applicators. Application shall be carried out in accordance

with instructions contained in this data sheet and referenced to CHEMCO INTERNATIONAL

TECHNICAL SPECIFICATION MANUAL. CHEMCO INTERNATIONAL management are intent on

ensuring all work is carried out in accordance with company HEALTH & SAFETY procedures andall materials are handled with due care to COSHH regulations and instructions.

Storage: Store in cool, dry conditions (not less than 4C or above 20C). Keep away from direct heat

source and sunlight. When not using the material always replace the lid on the container.

Shelf life: At least 24 months when stored in sealed containers at temperatures of not less than 4C or

above 20C. At temperatures above, refer to manufacturer for advice.

Pack sizes: 5 and 20kgs (other pack sizes available on request).

Theoretical coverage:5m/kg@ 100 microns.

(Allow for application losses, surface irregularities, etc).

Typical thickness range: 50 - 250 microns per coat.

Cure: Cross-linking polymerisation.

Mix ratio:Mix part A (resin RS 500P) and part B (hardener HR 500P)

in proportionate weights as supplied.

Volume solids: 100%

Colour: Medium grey (other colours are available on request).

PRODUCT DATA

Drying time (hours)*: Touch dry:

Hard dry:

4 - 8 2 - 4 8 - 12 4 - 8

12 - 16 6 - 8 24 12 - 16

*Depending on environmental factors such as humidity, airflow etc.

East Shawhead Industrial Estate

Coatbridge

ML5 4XD, Scotland UK

Tel: +44 (0) 1236 606060

Fax: +44 (0) 1236 606070

Email: [email protected]

Web: www.chemcoint.com

Documents

Chemco Marine Brochure