CDX-GT410U/GT414U - ESpecarchive.espec.ws/files/SONY CDX-GT410U_GT414U.pdf · Power requirements 12 V DC car battery ... To control CD/radio/MD/USB, the same as (SEEK) ... CDX-GT410U/GT414U

SERVICE MANUAL

Sony CorporationeVehicle DivisionPublished by Sony Techno Create Corporation

AEP ModelUK Model

9-887-452-022007C04-1 2007.03

Ver. 1.1 2007.03

SPECIFICATIONS

CD player sectionSignal-to-noise ratio 120 dBFrequency response 10 20,000 HzWow and flutter Below measurable limit

Tuner sectionFMTuning range 87.5 108 MHzAntenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo), 69 dB (mono)Harmonic distortion at 1 kHz

0.5% (stereo), 0.3% (mono)Separation 35 dB at 1 kHzFrequency response 30 15,000 Hz

MW/LWTuning range MW: 531 1,602 kHz

LW: 153 279 kHzAntenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzSensitivity MW: 30 V, LW: 40 V

USB player sectionInterface USB (Full-speed)Maximum current 500 mA

Power amplifier sectionOutputs Speaker outputs (sure seal connectors)Speaker impedance 4 8 ohmsMaximum power output

50 W 4 (at 4 ohms)

The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW

CD Drive Mechanism Type MG-101U-188//Q

Optical Pick-up Name DAX-25A

Continued on next page

CDX-GT410U/GT414U

FM/MW/LW COMPACT DISC PLAYER

(Photo: CDX-GT410U)

2

CDX-GT410U/GT414U

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE PART NUMBERS APPEAR AS SHOWN IN THISMANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of optical pick-up block.

SERVICE NOTES

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

GeneralOutputs Audio outputs terminal (sub/rear switchable)

Power antenna relay control terminalPower amplifier control terminal

Inputs Telephone ATT control terminalBUS control input terminalBUS audio input terminalAntenna input terminalAUX input jack (stereo mini jack)

Tone controls Low: 10 dB at 60 Hz (XPLOD)Mid: 10 dB at 1 kHz (XPLOD)High: 10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery (negative ground)Dimensions Approx. 178 50 179 mm

(7 1/8 2 7 1/8 in.) (w/h/d)Mounting dimensions Approx. 182 53 162 mm

(7 1/4 2 1/8 6 1/2 in.) (w/h/d)Mass Approx. 1.2 kg (2 lb. 11 oz.)Supplied accessories Card remote commander: RM-X151

Parts for installation and connections (1 set)USB cap

Design and specifications are subject to change withoutnotice.

US and foreign patents licensed from Dolby Laboratories.

optical pick-up

semi-fixed resistor

Notes on Chip Component Replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged

by heat.

TEST DISCSPlease use the following test discs for the check on the CD section.

YDES-18 (Part No. 3-702-101-01)PATD-012 (Part No. 4-225-203-01)

3

CDX-GT410U/GT414U

UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350C.Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful! Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

SERVO BOARDCN2

MAIN BOARDCN350 J-2502-076-1

EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)as shown below.

Connect the MAIN board (CN350) and the SERVO board (CN2)with the extension cable (Part No. J-2502-076-1).

This label is located on the bottom of the chassis.

This compact disc player is classified as a CLASS 1 LASERproduct. The CLASS 1 LASER PRODUCT label is located on theexterior.

CD playbackYou can play CD-DA (also containing CD TEXT*), CD-R/CD-RW (MP3/WMA/AAC files also containing Multi Session) andATRAC CD (ATRAC3 and ATRAC3plus format).

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

ATRAC CD

* A CD TEXT disc is a CD-DA that includes information such asdisc, artist and track name.

4

CDX-GT410U/GT414U

TABLE OF CONTENTS

1. GENERALLocation of Controls ........................................................ 5Connections ..................................................................... 6

2. DISASSEMBLY2-1. Sub Panel (FL) Assy ........................................................ 92-2. CD Mechanism Block ..................................................... 92-3. Main Board ...................................................................... 102-4. Servo Board ..................................................................... 102-5. Chassis (T) Sub Assy ....................................................... 112-6. Roller Arm Assy .............................................................. 112-7. Chassis (OP) Assy ........................................................... 12

3. DIAGNOSIS FUNCTION ........................................ 13

4. DIAGRAMS4-1. Block Diagram Main Section ...................................... 174-2. Block Diagram Display Section .................................. 184-3. Printed Wiring Board Main Section ............................ 204-4. Schematic Diagram Main Section (1/3) ...................... 214-5. Schematic Diagram Main Section (2/3) ...................... 224-6. Schematic Diagram Main Section (3/3) ...................... 234-7. Printed Wiring Board Key Section .............................. 244-8. Schematic Diagram Key Section ................................. 25

5. EXPLODED VIEWS5-1. Main Section .................................................................... 315-2. Front Panel Section ......................................................... 325-3. CD Mechanism Section (MG-101U-188//Q) .................. 33

6. ELECTRICAL PARTS LIST .................................. 34

NOTE FOR REPLACEMENT OF THE USB CONNECTOR(CN902)To replace the USB connector requires alignment.1. Insert the USB connector into the front panel.2. Place the KEY board on the front panel and align the terminals

of the USB connector with the holes in the KEY board.3. Solder the four terminals of the connector.

KEY board

front panel

USB (socket) connector

NOTE FOR REPLACEMENT OF THE SERVO BOARDWhen repairing, the complete SERVO board (A-1177-201-A) shouldbe replaced since any parts in the SERVO board cannot be repaired.

NOTE FOR THE 24-PIN CONNECTOR (CN901)Do not use alcohol to clean the 24-pin connector (CN901) connectingthe front panel with the main body.Do not touch the connector directly with your bare hand. Poor contactmay be caused.

Ver. 1.1

5

CDX-GT410U/GT414USECTION 1GENERAL This section is extracted

from instruction manual.

LOCATION OF CONTROLS

6

Location of controls and basic operations

Main unit

Card remote commander RM-X151

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.

A OFF buttonTo power off; stop the source.

B EQ3 (equalizer) button 11To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

C Volume control dial/select button 11To adjust volume (rotate); select setup items (press and rotate).

D SOURCE buttonTo power on; change the source (Radio/CD/MD*1/USB/AUX).

E Disc slotInsert the disc (label side up), playback starts.

F Display window

G USB terminalTo connect to the USB device. 10

H Z (eject) buttonTo eject the disc.

I PTY (Program Type) button 10To select PTY in RDS.

J (front panel release) button 5

AUX

OFF

DSPL

MODE

PUSH SELECT

SEEK SEEK

PAUSEDIM REP SHUF

EQ3 SOURCE

1 2 3 4 5 6GP/ALBM

AF/TA

PTY

12

qjqh

4 5 863

CDX-GT414UCDX-GT410Uqa qdq;9 qs qfqg

7

qk

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

+

4 wsqd

1

wf

ql

qf

wa

w;

wg

wd

7

K SEEK /+ buttonsCD/MD*1/USB*2:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold).Radio:To tune in stations automatically (press); find a station manually (press and hold).

L Receptor for the card remote commander

M MODE button 8, 13To select the radio band (FM/MW/LW); select the unit*3; select the play mode*4.

N DSPL (display)/DIM (dimmer) button 8, 9To change display items (press); change the display brightness (press and hold).

O RESET button (located behind the front panel) 4

P Number buttonsCD/MD*1/USB*2:(1)/(2): GP*5/ALBM*6 /+

To skip albums (press); skip albums continuously (press and hold)*7.

(3): REP 8(4): SHUF 8(6): PAUSE*8

To pause playback. To cancel, press again.

Radio:To receive stored stations (press); store stations (press and hold).

Q AF (Alternative Frequencies)/TA (Traffic Announcement) button 9To set AF and TA in RDS.

R AUX input jack 12To connect a portable audio device.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).

ql < (.)/, (>) buttonsTo control CD/radio/MD/USB, the same as (SEEK) /+ on the unit.

w; VOL (volume) +/ buttonTo adjust volume.

wa ATT (attenuate) buttonTo attenuate the sound. To cancel, press again.

ws SEL (select) buttonThe same as the select button on the unit.

wd M (+)/m () buttonsTo control CD, the same as (1)/(2) (GP/ALBM /+) on the unit.

wf SCRL (scroll) button 8To scroll the display item.

wg Number buttonsTo receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected.*2 When a USB device is connected.*3 When a CD/MD changer is connected.*4 When an ATRAC Audio Device is connected.*5 When an ATRAC CD is played.*6 When an MP3/WMA/AAC is played. *7 If the changer/USB device is connected, the

operation is different, see page 10, 13.*8 When playing back on this unit.

Notes When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc. If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see Replacing the lithium battery of the card remote commander on page 16.

About USB capWhen not using the USB terminal (G), use the supplied USB cap to prevent dust or dirt entering.Keep the USB cap out of the reach of children to prevent accidental swallowing.

6

CDX-GT410U/GT414U

CONNECTIONS

AUDIO OUT REAR*

BUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

A

B

* not supplied nicht mitgeliefertnon fourninon in dotazioneniet bijgeleverd

Source selector*Signalquellenwhler*Slecteur de source*

Selettore di fonte*Bronkeuzeschakelaar*

XA-C40

* AUDIO OUT SUB/REAR

Voorbeeldaansluitingen Opmerkingen (2-A) Sluit eerst de aardingskabel aan voordat u de versterker

aansluit. U hoort de pieptoon alleen als de ingebouwde versterker wordt

gebruikt.

Tip (2-B- )Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de bronkeuzeschakelaar XA-C40 (niet bijgeleverd) nodig.

Exemple de raccordement Remarques (2-A) Raccordez dabord le cble de mise la masse avant de

raccorder lamplifi cateur. Lalarme est mise uniquement lorsque lamplifi cateur intgr

est utilis.

Conseil (2-B- )Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le slecteur de source XA-C40 (non fourni) est indispensable.

Anschlussbeispiel Hinweise (2-A) Schlieen Sie unbedingt zuerst das Massekabel an, bevor Sie

den Verstrker anschlieen. Der Warnton wird nur ausgegeben, wenn der integrierte

Verstrker verwendet wird.

Tipp (2-B- )Zum Anschlieen von zwei oder mehr CD/MD-Wechslern wird der Signalquellenwhler XA-C40 (nicht mitgeliefert) bentigt.

Esempio di collegamento Note (2-A) Assicurarsi di collegare il cavo di terra prima di collegare

lapparecchio allamplifi catore. Lallarme viene emesso solo se in uso lamplifi catore

incorporato.

Suggerimento (2-B- )Per collegare due o pi cambia CD/MD, occorre utilizzare il selettore di fonte XA-C40 (non in dotazione).

Connection example Notes (2-A) Be sure to connect the ground (earth) lead before connecting

the amplifi er. The alarm will only sound if the built-in amplifi er is used.

Tip (2-B- )For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.

7

CDX-GT410U/GT414U

BUSCONTROL IN

BUS AUDIO IN

AUDIO OUT REAR*3

L

R

AUDIO OUTREAR/SUB

BUSIN

1 3 5 7

2 4 6 8

5 7

4 8

*1 from car antenna (aerial) von Autoantenne de lantenne de la voiture dallantenna dellauto van een auto-antenne

Fuse (10 A)Sicherung (10 A)Fusible (10 A)Fusibile (10 A)Zekering (10 A)

AMP REM

Light blueHellblauBleu cielAzzurroLichtblauw

Blue/white stripedBlauwei gestreiftRay bleu/blancRigato blu e biancoBlauw/wit gestreept

from the cars power connectorvom Stromanschluss des Fahrzeugsdu connecteur dalimentation de la voituredal connettore di alimentazione dellautovan de autovoedingsaansluiting

ATT

See Power connection diagram on the reverse side for details.

Nheres dazu fi nden Sie im Stromanschlussdiagramm. Blttern Sie dazu bitte um.

Voir le Schma de raccordement dalimentation au verso pour plus de dtails.

Per ulteriori informazioni, vedere Diagramma dei collegamenti di alimentazione che si trova sul retro.

Zie "Voedingsaansluitschema" op de achterkant voor meer details.

*1 Note for the antenna (aerial) connectingIf your car antenna (aerial) is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit.

*2 RCA pin cord (not supplied)*3 AUDIO OUT can be switched SUB or

REAR. For details, see the supplied Operating Instructions.

*1 Hinweis zum Anschlieen der AntenneWenn Ihre Autoantenne der ISO-Norm (Internationale Normungsgemeinschaft) entspricht, schlieen Sie sie mithilfe des mitgelieferten Adapters 2 an. Verbinden Sie zuerst die Autoantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgerts.

*2 Cinchkabel (nicht mitgeliefert)*3 AUDIO OUT kann zwischen SUB

und REAR umgeschaltet werden. Nheres hierzu fi nden Sie in der Bedienungsanleitung.

*1 Remarque sur le raccordement de lantenneSi votre antenne de voiture est de type ISO (Organisation internationale de normalisation), utilisez ladaptateur fourni

pour la r2 accorder. Raccordez dabord lantenne de voiture ladaptateur fourni et, ensuite, la prise dantenne de lappareil principal.

*2 Cordon broche RCA (non fourni)*3 AUDIO OUT peut tre commut sur SUB

ou REAR. Pour obtenir plus de dtails, reportez-vous au mode demploi.

*1 Nota per il collegamento dellantennaSe lantenna dellauto di tipo ISO (International Organization for Standardization), utilizzare ladattatore

in dotazione per collegar2 la. Collegare prima lantenna della macchina alladattatore in dotazione, quindi collegarla alla presa dellantenna dellapparecchio principale.

*2 Cavo a piedini RCA (non in dotazione)*3 AUDIO OUT pu essere impostato

su SUB o su REAR. Per ulteriori informazioni, consultare il manuale di istruzioni per luso.

*1 Opmerking bij de antenne-aansluitingIndien uw auto is uitgerust met een antenne van het type ISO (International Organization for Standardization), moet u die aansluiten met behulp van de bijgeleverde adapter 2. Sluit eerst de auto-antenne aan op de bijgeleverde adapter en vervolgens de antennestekker op het hoofdtoestel.

*2 Tulpstekkersnoer (niet bijgeleverd)*3 AUDIO OUT kan worden ingesteld

op SUB of REAR. Raadpleeg de gebruiksaanwijzing voor meer informatie.

Max. supply current 0.3 Amax. Versorgungsstrom 0,3 ACourant dalimentation maximum 0,3 AAlimentazione massima fornita 0,3 AMax. voedingsstroom 0,3 A

Negative polarity positions 2, 4, 6, and 8 have striped leads.An den negativ gepolten Positionen 2, 4, 6 und 8 befi nden sich gestreifte Adern.Les positions de polarit ngative 2, 4, 6 et 8 sont dotes de cordons rays.Le posizioni a polarit negativa 2, 4, 6 e 8 hanno cavi rigati.De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.

1PurpleViolettVioletViolaPaars

+

Speaker, Rear, RightLautsprecher hinten rechtsHaut-parleur, arrire, droit

Diffusore, posteriore, destroLuidspreker, achter, rechts

5WhiteWeiflBlanc

BiancoWit

+

Speaker, Front, LeftLautsprecher vorne links

Haut-parleur, avant, gaucheDiffusore, anteriore, sinistro

Luidspreker, voor, links

2

Speaker, Rear, RightLautsprecher hinten rechtsHaut-parleur, arrire, droit

Diffusore, posteriore, destroLuidspreker, achter, rechts

6

Speaker, Front, LeftLautsprecher vorne links

Haut-parleur, avant, gaucheDiffusore, anteriore, sinistro

Luidspreker, voor, links

3GrayGrauGris

GrigioGrijs

+

Speaker, Front, RightLautsprecher vorne rechtsHaut-parleur, avant, droit

Diffusore, anteriore, destroLuidspreker, voor, rechts

7GreenGrnVert

VerdeGroen

+

Speaker, Rear, LeftLautsprecher hinten links

Haut-parleur, arrire, gaucheDiffusore, posteriore, sinistro

Luidspreker, achter, links

4

Speaker, Front, RightLautsprecher vorne rechtsHaut-parleur, avant, droit

Diffusore, anteriore, destroLuidspreker, voor, rechts

8

Speaker, Rear, LeftLautsprecher hinten links

Haut-parleur, arrire, gaucheDiffusore, posteriore, sinistro

Luidspreker, achter, links

*2

Supplied with XA-C40Mit dem XA-C40 geliefertFourni avec le XA-C40In dotazione con il modello XA-C40Geleverd met de XA-C40

Supplied with the CD/MD changerMit dem CD/MD-Wechsler geliefertFourni avec le changeur de CD/MDIn dotazione con il cambia CD/MDGeleverd met de CD/MD-wisselaar

Source selector(not supplied)

Signalquellenwhler(nicht mitgeliefert)

Slecteur de source(non fourni)

Selettore di fonte(non in dotazione)

Bronkeuzeschakelaar(niet bijgeleverd)

XA-C40

from the cars speaker connectorvom Lautsprecheranschluss des Fahrzeugsdu connecteur de haut-parleur de la voituredal connettore dei diffusori dellautovan de autoluidsprekeraansluiting

Positions 1, 2, 3, and 6 do not have pins.An Position 1, 2, 3 und 6 be nden sich keine Stifte.Les positions 1, 2, 3 et 6 ne comportent pas de broches.Le posizioni 1, 2, 3 e 6 non hanno piedini.De posities 1, 2, 3 en 6 hebben geen pins.

4

YellowGelb

JauneGialloGeel

continuous power supplypermanente Stromversorgung

alimentation continuealimentazione continua

continu voeding

7

RedRot

RougeRossoRood

switched power supplygeschaltete Stromversorgung

alimentation commutealimentazione commutata

geschakelde voeding

5

BlueBlauBleuBlu

Blauw

power antenna (aerial) controlMotorantennensteuerung

antenne lectriquecomando dellantenna elettrica

elektrische antenne

8

BlackSchwarz

NoirNeroZwart

ground (earth)Massemasseterra

aarding

2

3

Aansluitschema

A Naar AMP REMOTE IN van een optionele versterkerDeze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het apparaat worden beschadigd.

B Naar het interface-snoer van een autotelefoon

WaarschuwingIndien u een elektrische antenne hebt zonder relaiskast, kan het aansluiten van dit apparaat met de bijgeleverde voedingskabel 3 de antenne beschadigen.Opmerkingen over de bedienings- en voedingskabels De bedieningskabel van de elektrische antenne (blauw) levert

+12 V gelijkstroom wanneer u de tuner inschakelt of de AF (alternatieve frequenties) of TA (verkeersinformatie) functie activeert.

Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de achterruit/zijruit, moet u de bedieningskabel van de elektrische antenne (blauw) of de voedingskabel van de accessoires (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details.

Met dit apparaat is het niet mogelijk een elektrische antenne zonder relaiskast te gebruiken.

Instandhouden van het geheugenZolang de gele voedingskabel is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer de contactschakelaar van de auto wordt uitgeschakeld.

Opmerkingen betreffende het aansluiten van de luidsprekers Zorg dat het apparaat is uitgeschakeld, alvorens de

luidsprekers aan te sluiten. Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm

en let op dat die het vermogen van de versterker kunnen verwerken. Als u dit niet doet, kunnen de luidsprekers ernstig beschadigd raken.

Verbind in geen geval de aardingskabel van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter- en linkerluidspreker niet op elkaar aan.

Verbind de aarddraad van dit apparaat niet met de negatieve () aansluiting van de luidspreker.

Probeer nooit de luidsprekers parallel aan te sluiten. Sluit geen actieve luidsprekers (met ingebouwde versterkers)

aan op de luidsprekeraansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan.

Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve () kabel is voor de rechter- en linkerluidsprekers.

Verbind de luidsprekerkabels niet met elkaar.

Opmerking over aansluitenAls de luidspreker en versterker niet goed zijn aangesloten, wordt "FAILURE" in het display weergegeven. In dit geval moet u zorgen dat de luidspreker en versterker correct zijn aangesloten.

Schmas de raccordement

A Au niveau du AMP REMOTE IN dun amplifi cateur de puissance facultatifCe raccordement existe seulement pour les amplifi cateurs. Le raccordement tout autre systme peut endommager lappareil.

B Vers le cordon de liaison dun tlphone de voiture

AvertissementSi vous disposez dune antenne lectrique sans botier de relais, le branchement de cet appareil au moyen du cordon dalimentation fourni 3 risque dendommager lantenne.Remarques sur les cbles de commande et dalimentation Le cble de commande (bleu) fournit du courant continu de

+12 V lorsque vous mettez le tuner sous tension ou lorsque vous activez la fonction AF (frquence alternative) ou TA (messages de radioguidage).

Lorsque votre voiture est quipe dune antenne FM/MW (GO)/LW (PO) intgre dans la vitre arrire/latrale, raccordez le cble de commande dantenne (bleu) ou le cble dalimentation des accessoires (rouge) la borne dalimentation de lamplifi cateur dantenne existant. Pour plus de dtails, consultez votre revendeur.

Une antenne lectrique sans botier de relais ne peut pas tre utilise avec cet appareil.

Raccordement pour la conservation de la mmoireLorsque le cble dalimentation jaune est connect, le circuit de la mmoire est aliment en permanence mme si la cl de contact est en position darrt.

Remarques sur le raccordement des haut-parleurs Avant de raccorder les haut-parleurs, mettez lappareil hors

tension. Utilisez des haut-parleurs ayant une impdance de 4 8 ohms

et une capacit adquate sous peine de les endommager. Ne raccordez pas les bornes du systme de haut-parleurs au

chssis de la voiture et ne pas connecter les bornes du haut-parleur droit celles du haut-parleur gauche.

Ne raccordez pas le cble de mise la masse de cet appareil la borne ngative () du haut-parleur.

Ne tentez pas de raccorder les haut-parleurs en parallle. Connectez uniquement des haut-parleurs passifs. Le

raccordement de haut-parleurs actifs (avec des amplifi cateurs intgrs) aux bornes des haut-parleurs pourrait endommager lappareil.

Pour viter tout problme de fonctionnement, nutilisez pas les cbles des haut-parleurs intgrs installs dans votre voiture si lappareil dispose dun cble ngatif commun () pour les haut-parleurs droit et gauche.

Ne raccordez pas entre eux les cordons des haut-parleurs de lappareil.

Remarque sur le raccordementSi les haut-parleurs ne sont pas raccords correctement, le message FAILURE saffi che. Dans ce cas, assurez-vous que les haut-parleurs sont raccords correctement.

Anschlussdiagramm

A An AMP REMOTE IN des gesondert erhltlichen EndverstrkersDieser Anschluss ist ausschlielich fr Verstrker gedacht. Schlieen Sie nichts anderes daran an. Andernfalls kann das Gert beschdigt werden.

B An Schnittstellenkabel eines Autotelefons

WarnungWenn Sie eine Motorantenne ohne Relaiskstchen verwenden, kann durch Anschlieen dieses Gerts mit dem mitgelieferten Stromversorgungskabel 3 die Antenne beschdigt werden.Hinweise zu den Steuer- und Stromversorgungsleitungen Die Motorantennen-Steuerleitung (blau) liefert +12 V

Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.

Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schlieen Sie die Motorantennen-Steuerleitung (blau) oder die Zubehrstromversorgungsleitung (rot) an den Stromversorgungsanschluss des vorhandenen Antennenverstrkers an. Nheres dazu erfahren Sie bei Ihrem Hndler.

Es kann nur eine Motorantenne mit Relaiskstchen angeschlossen werden.

Stromversorgung des SpeichersWenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zndung) mit Strom versorgt.

Hinweise zum Lautsprecheranschluss Schalten Sie das Gert aus, bevor Sie die Lautsprecher

anschlieen. Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und

8 Ohm und ausreichender Belastbarkeit. Ansonsten knnen die Lautsprecher beschdigt werden.

Verbinden Sie die Lautsprecheranschlsse nicht mit dem Wagenchassis und verbinden Sie auch nicht die Anschlsse des rechten mit denen des linken Lautsprechers.

Verbinden Sie die Masseleitung dieses Gerts nicht mit dem negativen () Lautsprecheranschluss.

Versuchen Sie nicht, Lautsprecher parallel anzuschlieen. An die Lautsprecheranschlsse dieses Gerts drfen nur

Passivlautsprecher angeschlossen werden. Schlieen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstrkern) an, da das Gert sonst beschdigt werden knnte.

Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am Ende eine gemeinsame negative () Leitung fr den rechten und den linken Lautsprecher verwendet wird.

Verbinden Sie nicht die Lautsprecherkabel des Gerts miteinander.

Hinweis zum AnschlieenWenn die Lautsprecher nicht richtig angeschlossen sind, erscheint FAILURE im Display. Vergewissern Sie sich in diesem Fall, dass die Lautsprecher richtig angeschlossen sind.

Schema di collegamento

A A AMP REMOTE IN di un amplifi catore di potenza opzionale Questo collegamento riservato esclusivamente agli amplifi catori. Non collegare un tipo di sistema diverso onde evitare di causare danni allapparecchio.

B Al cavo di interfaccia di un telefono per auto

AvvertenzaQuando si collega lapparecchio con il cavo di alimentazione in dotazione 3, si potrebbe danneggiare lantenna elettrica se questa non dispone di scatola a rel.Note sui cavi di controllo e di alimentazione Il cavo (blu) di controllo dellantenna elettrica fornisce

alimentazione pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA (notiziario sul traffi co) o AF (frequenza alternativa).

Se lautomobile dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dellantenna elettrica o il cavo (rosso) di ingresso dellalimentazione ausiliaria al terminale di alimentazione dellamplifi catore di potenza dellantenna esistente. Per ulteriori informazioni, consultare il proprio fornitore.

Non possibile usare unantenna elettrica senza scatola a rel con questo apparecchio.

Collegamento per la conservazione della memoriaQuando il cavo di alimentazione giallo collegato, viene sempre fornita alimentazione al circuito di memoria anche quando linterruttore di accensione spento.

Note sul collegamento dei diffusori Prima di collegare i diffusori spegnere lapparecchio. Usare diffusori di impedenza compresa tra 4 e 8 ohm e con

capacit di potenza adeguata, altrimenti i diffusori potrebbero venire danneggiati.

Non collegare i terminali del sistema diffusori al telaio dellauto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro.

Non collegare il cavo di terra di questo apparecchio al terminale negativo () del diffusore.

Non collegare i diffusori in parallelo. Assicurarsi di collegare soltanto diffusori passivi, poich

il collegamento di diffusori attivi, dotati di amplifi catori incorporati, ai terminali dei diffusori potrebbe danneggiare lapparecchio.

Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nellautomobile se lapparecchio condivide un cavo comune negativo () per i diffusori destro e sinistro.

Non collegare fra loro i cavi dei diffusori dellapparecchio.

Nota sui collegamentiSe il diffusore non collegato correttamente, FAILURE viene visualizzato nel display. In tal caso, accertarsi che il diffusore sia collegato correttamente.

Connection diagram

A To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

B To the interface cable of a car telephone

WarningIf you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power connecting lead 3 may damage the antenna (aerial).Notes on the control and power suppy leads The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffi c Announcement) function.

When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.

A power antenna (aerial) without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

Do not connect the ground (earth) lead of this unit to the negative () terminal of the speaker.

Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative () lead for the right and left speakers.

Do not connect the units speaker leads to each other.

Note on connectionIf speaker and amplifi er are not connected correctly, FAILUREappears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

8

CDX-GT410U/GT414USECTION 2

DISASSEMBLY

Note: This set can be disassemble according to the following sequence.

2-1. SUB PANEL (FL-U) ASSY(Page 9)

2-2. CD MECHANISM BLOCK(Page 9)

SET

2-3. MAIN BOARD(Page 10)

2-5. CHASSIS (T) SUB ASSY(Page 11)

2-6. ROLLER ARM ASSY(Page 11)

2-7. CHASSIS (OP) ASSY(Page 12)

2-4. SERVO BOARD(Page 10)

1. CHUCKING ARM SUB ASSY(SUPPLEMENT-1 Page 1)

2. SLED MOTOR ASSY(SUPPLEMENT-1 Page 2)

3. OPTICAL PICK-UP SECTION(SUPPLEMENT-1 Page 3)

4. OPTICAL PICK-UP(SUPPLEMENT-1 Page 3)

Ver. 1.1

9

CDX-GT410U/GT414U

2-2. CD MECHANISM BLOCK

Note: Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (FL) ASSY

2 two claws

3 two claws

4 sub panel (FL-U) assy

1 two screws (+PTT 2.6 6)

4 CN350

5 CN352 (3P)

3

1 screw(+PTT 2.6 6)

2 screw(+PTT 2.6 6)

6 two screws(+PTT 2.6 4)

7 bracket (CD)8 CD mechanism block

10

CDX-GT410U/GT414U

2-4. SERVO BOARD

2-3. MAIN BOARD

0 MAIN board

insulating sheet3


8 screw(+PTT 2.6 10)

7 screw(+P 2.6 10)

9 heat sink

5 two screws(+P 2.6 8)



1 three screws(+BTT 2.6 5)

5 SERVO board

SERVO board

claw

claw

3 toothed lock screw(M 1.7 2.5)

2 toothed lock screw(M 1.7 2.5)

1 Remove the eleven solders.

GRYYELBLU

ORGREDBLKREDWHT

BLKREDWHT

4 optical pick-up (16 core)(CN1)

11

CDX-GT410U/GT414U

2-6. ROLLER ARM ASSY

2-5. CHASSIS (T) SUB ASSY

4 chassis (T) sub assy

3 claw

1 two precision screws(+P 1.7 2.2)

2 two precision screws(+P 1.7 2.2)

3 washer

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)

12

CDX-GT410U/GT414U

2-7. CHASSIS (OP) ASSY

7 coil spring (damper) (natural)

8 coil spring (damper) (green)

6 chassis (OP) assy

5

1 tension spring (KF)

2 gear (LE1)

3 lever (D)

4 slider (R)

Ver. 1.1

13


DIAGNOSIS FUNCTION

Description of the Diagnostics function:

1. Setting the Diag display modeWith the power off, press the [4] button, [5] button, and [4] buttonon the set body or the remote control (for more than 2 seconds)in turn.

2. Canceling the Diag display modeDuring the Diag function mode, press the [OFF] button.

3. Initial display in the Diag display mode.Just when the Diag mode is entered, reset count is displayed.The display mode is switched by each rotation of SEEK +/M > or SEEK /. m keys.

4. Contents of each display mode4-1. Reset count display mode

4-2. Reset count by watchdog timer display mode

4-3. Number of connected units display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the number of connected units displaymode.

4-4. Operating hours display mode

Reset count (in hexadecimal format)

Diag code01: Reset count

0 1 X X

Reset count (in hexadecimal format)

Diag code 02: Number of resets by watchdog timer

0 2 X X

Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format).

Recency of information1-3: 1 represents the latest.

Diag code03: Number of connected unit.

0 3 1 X X X

No. of connected units history 1 (latest) display

No. of connected units history 3 display

No. of connected units history 2 display

0 3 1 X X X

0 3 2 X X X

0 3 3 X X X

Operating hours (in hexadecimal format)

Diag code04: Operating hours

0 4 X X X X

Reset count display

OFFSET/FAILURE error display

CD error information display

Operating hours display

Number of connected units display

Reset count by watchdog timer display

0 1 X X

0 2 X X

0 3 1 X X X

0 4 X X X X

0 5 1 X X

0 6 1 X X X X X

USB error information display

0 7 1 X X

14

CDX-GT410U/GT414U

4-5. CD error information display mode4-5-1. Error description

4-5-2. Disc type and operating hours

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

4-6. OFFSET/FAILURE error display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the OFFSET/FAILURE error displaymode.

Error description (in hexadecimal format)


Diag code05: CD error information

0 5 1 X X

Operating hours


Diag code05: CD error information

0 5 1 X X X X

CD error info history 1 (latest)Error description plus error details display

CD error info history 3Disc type plus operating hours display

CD error info history 3Error description plus error details display

CD error info history 2Disc type plus operating hours display

CD error info history 2Error description plus error details display

CD error info history 1 (latest)Disc type plus operating hours display

0 5 1 X X X X

0 5 2 X X

0 5 2 X X X X

0 5 3 X X

0 5 3 X X X X

0 5 1 X X

Operating hours


Diag code06: OFFSET/FAILURE

Error description (0: OFFSET, 1: FAILURE)

0 6 1 X X X X X

OFFSET/FAILURE error history 1 (latest) display

OFFSET/FAILURE error history 3 display

OFFSET/FAILURE error history 2 display

0 6 2 X X X X X

0 6 3 X X X X X

0 6 1 X X X X X

Error informationIndication Description

1X SERVO ERROR3X LOADING ERROR4X TRACK JUMP5X TEXT ERRORFX MECHA ERROR

Disc typeIndication Disc type

0 MP31 WMA2 AAC3 ATRAC8 CD/DAF UNKNOWN

4-7. USB error information display mode4-7-1. Error description

Error description (in hexadecimal format)


Diag code07: USB error information

0 7 1 X X

Error informationIndication Description

15 DEVICE ERROR

17FILE ERROR(NO MUSIC)

1E POWER ON ERROR1F BOOT ERROR

3AINVALID EJECTERROR

43 READ ERROR

44INVALIDFORMAT FILE

FANOT SUPPORTDEVICE

FBHUB NOTSUPPORT

15

CDX-GT410U/GT414U

4-7-2. Disc type and operating hours The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

USB error info history 1 (latest)Error description plus error details display

USB error info history 3Disc type plus operating hours display

USB error info history 3Error description plus error details display



USB error info history 1 (latest)Disc type plus operating hours display

0 7 1 X X X X X

0 7 2 X X

0 7 2 X X X X

0 7 3 X X

0 7 3 X X X X X

0 7 1 X X





0 7 4 X X

0 7 4 X X X X

0 7 5 X X

0 7 5 X X X X

Operating hours


Diag code07: USB error information

0 7 1 X X X X

16

CDX-GT410U/GT414U

MEMO

17 17CDX-GT410U/GT414U

CDX-GT410U/GT414U

4-1. BLOCK DIAGRAM MAIN SECTION

SECTION 4DIAGRAMS

J901

AUX

AUX R-CH

1 ANT

SCLSDA

CDMONCDON

9 AUX-LCH

ELECTRONIC VOLUMEIC401

J1(ANTENNA)

TU1(TUNER UNIT)

I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR

IC300

SYSTEM CONTROLIC501 (1/2)

CN300

7 AUX-RCH

BATT

6 CD-LCH5 CD-RCH

6S-METER7TU MUTE

16E2P SCL17E2P SDA

39 VSM

5QUALITY

9RDS OUT

38 QUALITY8MUTE CON 53 TU ATTIN

56 DAVN

BU+3.3V

26 RDS ON

95 CDMON94 CDON61 Z MUTE

11VDD+5V

4L-CH3R-CH

BU+3.3V

10VCC

12 TUATT

13 NSMASK

25 EEP CKO24 EEP SIO

CD ONCDM ON

CD LCD R

4 TU-LCH3 TU-RCH

CD-RCH

A ATT

R-CH(REAR)

TU-RCH

AUDIO+8.3V

AUDIO+8.3V

24OUT-RRR-CH(FRONT)26OUT-FR

53

OUT FL+OUT FL

97

OUT RL+OUT RL

2927

AMP REM

R-CH

ANT REM

BATT

3037

AUDIO+B

35VP

BU+B3133

SERVO3.3VMECHA6V

34PANEL+B

28MUTE

2 SDA

AUDIO+8.3VBU+5VSERVO+3.3VMECHA+6VPANEL+B

4 SCL

SDASCL

16 BEEP22 STB25 DIAG

15

13

7

10

12

11

16

19

2

4

3

56

2930

SCLSDA

SCLSDA

SCLSDA

9VOLATT

100ATT

33I2C SCK34I2C SIO

96

BUIN

97TESTIN

12 IN FL FL+FL

RL+RL

FR+FRRR+RR

AMP-REMANT-REM

ACC

TEST

11 IN RL23OUT-RL

25OUT-FL

MUTEQ432

AUDIO OUTREAR/SUB

MUTE CONTROLSWITCH

Q491,492

60

UNISI54

UNISO

58

UNISCK

59

BUSON

88SYSRST

12

B/U-C11

DATA OUT10

DATA IN8

CLK IN

9

BUS IN

13 RST

RESET

3

56

8

423

1

BATT

CLK 4DATA I/O

1BUS ON

2RST

SYSR

ST

99ACCIN ACCESSORY CHECKQ702

BATTBATT

BATTERYCHECKQ605

BUS INTERFACEIC601

MUTEQ470

MUTEQ401

MUTE CONTROLSWITCH

Q411,412

MUTEQ440

D491

F901

R-CH2122

SUBOUT-LSUBOUT-R

R-CH

L

R

J652 (2/2)

BUSCONTROL IN

D353

D602

DISPLAY SECTIONA

TH400

CNJ4007

BATT

TUNER+5VREGQ3

NOISE MASKSWITCH

Q1

RDS+3.3VSWITCH

Q50

RDS MODULATORIC50

15E2PVDD

13TU-SCL14TU-SDA

BU+5VBU+3.3V

REGIC681

TEL ATT98TELATTTELEPHONE ATTENATION

CHECKQ701

5DIAG8AMPSTB

7BEEP

BUSAUDIO

IN BUS-RCH

L

R

J652 (1/2)

2 BUS-LCH1 BUS-RCHBUS-RCH

CD-RCH

AUX-RCH

TU-RCH

ZMUTE

93 WAKE UPWAKE UP

27 MC RXMC RX

28 MC TXMC TX

Z MUTE

SYS RST

MECHA+6VBU+3.3V

SERVO+3.3V

B/U CHECK

RXD

TXD

DR+6V

BU+3.3V

A+3.3V

D+3.3V

CDONCDMONZMUTE

WAKE UP WAKE UP

SYSRST

B/U CHECK

MC TX

MC RX

CDMECHANISM

UNIT(MG-101U)

(1/2)

6

11SCL

15INTN

16 MPX

XTO

XTI

12SDA

SCLSDA

1VDDA7VDDD

10

9

X508.664MHz

B/U

CHEC

K

Signal Path R-CH is omitted due to same as L-CH.

: CD PLAY

: FM

: AUX

: MW/LW(Page 18)

1818CDX-GT410U/GT414U

CDX-GT410U/GT414U

4-2. BLOCK DIAGRAM DISPLAY SECTION

RESETMAIN

SECTION A

KEY ACKNOWLEDGESWITCH

Q664

83

82

41

192018

40

52

48

64

SYSTEM CONTROLIC501 (2/2)

USB CONTROLIC804

DC-DC CONVERTERIC803

SHIFTCONTROLSWITCH

Q805

FL901FLUORESCENT

INDICATOR TUBE

KEYIN0

CLKCS

FL SOFL SCK

FL CS

20

19

16

GRID1

GRID2

GRID3

411G

15RESET

40Q1

39Q2

F+

F

5VDD(+3.3V)

KEYIN1

31 RE-IN032 RE-IN1

KEYACK

AD ON

62 NOSESW

SIRCS

77 RESET

FL VH+12V

OSCOUT

OSCIN

89FL ON

X50118.432MHz

1214

10

3G

D50317

18

6

42

12

44

45

2G

DIO

PANEL+B

BU+3.3V

KEY MATRIX

80

79

XOUT

XIN

X50232.768kHz

10FSW IN

91USB OVER

92USB ON

90DD ON

75FSW OUT

LSW901,902S901904,906915

(VOLUME)

PUSH SELECTRE901

ROTARYENCODER

REMOTE CONTROLSIGNAL RECEIVER

IC971

RESETIC602

PANEL+B

BATT

PANEL+B

LED841847,850857,861864,LSW901,902

LED941947,950957,961963,LSW901,902

IN OUT

USB DUSB D+

4 /EN5 /OC

1

7

6 5

3

223

678

FL DRIVEQ883

FL DRIVEQ882

LED DRIVEQ991

LED DRIVEQ992

FL DRIVEQ881

PANEL+B

9VH

VDD+3.3VREG

IC972

FL+3VREG

IC802

S103RESET

D804

FL +12VREG

IC801

SWBATT

INV

FB

VIN

EN

RT

D801

1 CN902

CN902

CDMECHANISM

UNIT(MG-101U)

(2/2)

234

(Page 17)


CDX-GT410U/GT414U

Waveforms

MAIN Board

NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)

For schematic diagrams.Note: All capacitors are in F unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

All resistors are in and 1/4 W or less unless otherwise

specified. f : internal component. C : panel designation.

For printed wiring boards.Note: X : parts extracted from the component side. Y : parts extracted from the conductor side. a : Through hole. : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

A : B+ Line. B : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. no mark : FM

( ) : MW/LW< > : CD PLAY

: Impossible to measure Voltages are taken with a VOM (Input impedance 10 M).

Voltage variations may be noted due to normal productiontolerances.

Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

Circled numbers refer to waveforms. Signal path.

J : CD PLAYF : FMf : MW/LWL : AUX

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

1.1 Vp-p

8.664 MHz

3 IC50 9 (XTI)

0.8 Vp-p

32.768 kHz

1 IC501 i; (XOUT)

1 Vp-p

18.432 MHz

2 IC501 is (OSC IN)

0.2 V/DIV, 20 sec/DIV

0.5 V/DIV, 0.1 sec/DIV

0.5 V/DIV, 0.1 sec/DIV


CDX-GT410U/GT414U

: Uses unleaded solder.4-3. PRINTED WIRING BOARD MAIN SECTION

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

L RJ1

(ANTENNA) L R

J652

-1 -2 -3 -4

AUDIO OUTREAR/SUB

BUSAUDIO IN

CN2

CN101

CDMECHANISM

UNIT(MG-101U)

BATT

1

3

1

4

8 7

3 2 1

6 5 4

34

21

1

5

1

7

1

5

X501 S103RESET

1-872-031- 11

R55

2

JC38

C890

D153

C951

C820

C704

C705

R673

D503

JC905

IC802

R8

R9

R672

C302

R553

JC91

2

IC40

1

D802

R815

R814

R813 D80

1

R816

R818

R890

C812 R

819

R82

0

Q805

C814

C808

IC804

R89

1

JC81

0C8

07

C445

R812

R81

1

C805

R810

IC681

C804

R80

9

C802R529

C810

Q3

R351

R570

JC90

7

L402

L411

JC90

9

JC91

0

JC92

7

JC924

R903

JC923

JC92

2

JC92

9

R612 R615

R912

C317

JC931

JC930JC92

8

C7

R91

7

D105C3

29

D10

7

D10

6

JC21

D11

1

D11

2

JC921

R152

D10

9

R606

D108

R607

D113

JC926

JC939

C509

JC940R920

R81

7

JC94

3

C703

C313

R923

C315

R925

R924

R70

9

D703

R701

D704

R703R704

R70

2

Q701D70

2

R70

6

Q702

R70

8

R70

7

D605

D606

D603

D602

R611

L409

R616

JC22

C601

R601

R602

C402

R402

R401

L410

C418

C419

L406

L401

C307

IC602

C305

C309

L403

C417

IC60

1

C415

L405

JC19

R901

R902

JC90

6

JC941

C301

C325

C516

C330

C304

JC93

3

C515

JC36

R537

R551R573

R523

R53

4R

557

R544

R556

R559

R520

JC81

1

JC934

IC801

C702

JC938

JC93

5

R511

JC33

JC32

R555

R568

C507

C508

C320

R91

0

C504

R52

1

R52

2

C513

C501

C512 C514

R50

4

R505

R502

R503

C502

R671

R565

R56

7

R561

L4

R517

Q664

JC16

C510

R519

D502

R674

R56

3

C519

R564

R636

JC18

JC24

D353

R60

0

D90

1

JC23

JC90

3

C312

JC920

JC904

R61

C681

Q42

0

Q44

0

C412

C682

D604

D2

Q605

R531

Q49

1

Q49

2

R604

R491

JC902

D491

R60

3

R2

R3R4 R5

R10

C3

C6

L1

R12

R13R6

R7

C8

JC5

D110

CN352

R151

R154

R15

5

JC93

2

R153

L151

L901

L902

JC17

R533R532

L407

JC90

1

JC936

JC913

JC914

R50

9

JC942

R919

R918

JC12

C816

R558

JC28

C361

C362

C413C414

R35

7

R358

R355R356

R420

R440

R460

R470

R452

R430

R48

5C4

84

R45

1

R431

JC4

JC30

JC29

C443

C426C423

Q43

2Q

452

C454

C318

R301

JC8

JC14

JC31

R450 R449

C432 C452

R448 R447

R44

2

R421

R471

R461

Q460

Q470

C434

R46

2

R472C463C462

C472 C473

JC9

C444

C424

R54

0

R51

0

R52

6

JC1

R95

1

R95

2C319

R96

1

R302

C157

D10

2

D10

1D10

4

D10

3

C905

C891

C892

C921

C924

JC91

1

R150

R35

4

JC11

L501

R91

3

IC50

1

R80

2R

803

R591

L804

L805

R59

2 R59

3

Q401

Q402

JC40

1

Q411

Q412

R41

1

R493

R91

6

R91

5

R91

4

R40

3R40

4

D15

2

D151

(CHASSIS)

R926

R92

7

R536

R59

5

R59

6

R59

7

R598

R599

R15

6R

157

R15

8

D156

JC10

R800

C706

C707

D706

D707

JC705

C158

C159

R58

L50

R57Q50

C57C56

C55C54

IC50R54

C52

R53

R52

C53

C50C51

R55

C58

C953 R15

L2

L3

R60

C493

C494

Q1

R1

TU1(TUNER UNIT)

JW1

JW2

JW22

JW23

JW24

JW28

JW34

JW35

JW38

JW42

JW43

JW44

JW45

JW46JW

49

JW50

YEL

JW51

JW52

JW53

JW56 JW

57

JW58

JW59

JW60

JW61

JW66 J

W68

JW74

JW75

JW76

JW77

JW79

JW95

JW96

JW97

JW98

JW99

JW101

JW102

JW103

JW10

5

JW10

6

JW26

JW25

JW33

JW32

JW31

JW36

JW29

JW81

JW80

JW19

JW20

JW21

JW12

JW11

JW10

JW9

JW10

9

JW10

8

JW100

JW11

0

JW17

JW16

JW15

JW14

JW13JW8

JW92

JW91

JW89

JW86

JW83

JW62

JW64

JW63

JW65

JW69

JW84

JW67

JW48

JW47

JW27

JW3

JW4

JW30

JW70

JW71

JW72

JW73

JW78

JW82

JW85

JW87

JW88

JW90

JW10

4

JW11

1

JW113

JW114

JW115

JW116

JW119

JW120JW121

JW122

JW123

JW12

4JW

125

JW12

6

JW12

7

JW12

8

JW12

9

JW130

JW131

JW132

JW13

3

JW134

JW135

JW13

6

JW137

JW13

8

D607

S103

C803

D304

D303

D30

8

C623

D30

7

C622

C683

D31

1D312

L818

D310

C316C3

14

X50

R705

D301

C809

IC803

D302

C403

C401

C701

YEL

C308

C306

C405

C409

C806

C811X5

01

CN350

D309

D30

6

D30

5

TH400

X502

L300

L802

L803

C61

C491

CN300

C2

C5

C153

C152

C151

C818

CN370

C364

C363

C365

C366 C4

86

C485

C431

C451

C461C471

C441

C421

C303

C801

JW18

JW54

JW55

JW11

8

D804

JW139

C624

C625

C626

C815

JW10

7

JW5

JW117

JW112

JW94

JW93

CNJ400

CNJ400(BUS CONTROL IN)

IC300

C406

C407

JW14

0

JW41

JW40

JW39

C819

C600

JW7

C1

F901

R710

CN351

(Page 24)

D2 E-2D101 I-4D102 I-4D103 I-4D104 I-4D105 J-7D106 I-4D107 I-4D108 I-3D109 I-2D110 I-4D111 I-4D112 I-4D113 H-3D151 I-2D152 I-2D153 I-3D156 I-2D301 C-8D302 D-8D303 C-9D304 D-9D305 C-6D306 C-6D307 C-6D308 C-6D309 C-6D310 C-6D311 C-7D312 C-7D353 H-8D491 E-5D502 H-7D503 I-6D602 D-10D603 D-10D604 E-10D605 D-9D606 D-9D607 D-9D702 C-8

Semiconductor LocationRef. No. Location Ref. No. Location

D703 C-9D704 C-8D706 C-9D707 D-8D801 F-10D802 F-9D804 H-9D901 B-10

IC50 G-2IC300 B-6IC401 D-3IC501 G-6IC601 E-10IC602 G-7IC681 D-6IC801 I-10IC802 H-10IC803 G-10IC804 H-9

Q1 E-2Q3 F-2Q50 H-2Q401 F-4Q402 E-4Q411 E-5Q412 E-4Q420 B-4Q432 B-3Q440 B-4Q452 C-3Q460 C-4Q470 C-4Q491 E-5Q492 E-5Q605 D-10Q664 I-6Q701 C-8Q702 C-8Q805 G-11


CDX-GT410U/GT414U

4-4. SCHEMATIC DIAGRAM MAIN SECTION (1/3) Refer to page 26 for IC Block Diagrams.

IC B/D

IC B/D

C701

C303

C600

D606

C622

C306

R301

R302

C623

R604 R603

R706 R708

R703

R704

Q492

C491

R491

R600

R531

JC36

JC905

C626

C625

C624

R599

Q491

C601

JC909

C702 C703

C705

C704

L300

C319 C318

C317

C325

C301

C302

C444 C424 C330

C304

C454 C434

C305 C307

C309

JC939

JC940

R615

JC31JC30JC29

L902

L901C308

JC12

C312 C3

20

C314

C313

C316

C315

C681C682C683

IC681IC602

R961

R493 JC8

JC1

R701

R705

R709

R702

R707

R612

R607

R606

JC21

JC22 R611

R616 R602

R601

IC300

IC601

JC33 JC32

F901

Q701

Q702

Q605

CNJ400

TH400

JC910

JC19

D30

2

D30

1

D30

4

D303D305D306D307D308D309D310D311D312

C706

C707

JC705

CN300

D704

D703

D707

D706

D702

D607

D603 D602

D604D605D901

D491

R710

C329

(Page 23)

(Page 22)


CDX-GT410U/GT414U

4-5. SCHEMATIC DIAGRAM MAIN SECTION (2/3) Refer to page 19 for Waveforms. Refer to page 26 for IC Block Diagrams.

(Page 21)

(Page 23)

IC B/D IC B/D

R442R421 R451 R431

C441C421 C451 C431

X50

R52

R55

R53

R1

R10

R58

R57

Q440Q420 Q452 Q432

R447R448 R449 R450

R12 R13

R15

L50

R430

R420

R460

R470

R440

R452

R357 R358

R355 R356

C365

C366

C461

R461

C471

R471

R462R472

C485

R153R155

L1

JC9

JC28

R918

R919

C953

R150

C406

C407

Q401

Q402

Q411

Q460Q470

Q412

C426 C423

C445 C443

C473 C472

C484

C494

C493

JC4

C463 C462

C452 C432 C413 C414

C905

C362

C361

JC943

C6

C3

C8

C58C50

C55

C54 C56

C157

JC926

L818

C921

CN352

L805

R152

R151

L151

JC927

C924

JC923

L804

C818

JC928JC930

JC929JC931

R913

J1

R5

R4

R2

R3

C1

R8

R9

JC5JC11

R354

R920

JC401

R411

R15

6

R15

8

R15

7

R485

JC942 JC941

C7

R6 R7

L4

R558

R54

C51C52

C53 L2

L3

R60

R61

C57

C151

C153

C152

R154

C820

R912

JC920

JC921

JC922

R952

R951

JC924

CN370

J652TU1

Q1

Q3

Q50

C486

IC50IC401

C2

C364

C363

R403

R404

C158

C159

C5

D2

C61

D151

D152D156

D153

D103

D102

D101

D104

D106

D107

D109

D108

D113

D111

D112

D110

D105

JC10

(Page 25)


CDX-GT410U/GT414U

4-6. SCHEMATIC DIAGRAM MAIN SECTION (3/3)

Refer to page 19 for Waveforms. Refer to page 27 for IC Block Diagrams. Refer to page 28 for IC Pin Description of IC501.

(Page 21) (Page 22)

IC B/D IC B/D

IC B/D

X502

C409

R351

R502

R53

7

R401

R402 L401

L410

L403

L407

R55

1

R57

3

R55

7

R51

1

R51

0

R53

2

R53

4

R55

3

R567R565

R561

R503

D353

R540

R555

R520

R523

L501

L803

R813

L802

C803 C806

Q805

R811

R812R810

R809

R816

R817

JC901 R901

L411

R925

C891

R55

2

R59

1

R592

R593

R927

R595

CN350JC902

JC903

C415

L406

L405

C892

C804

C402

C419

C412

C507

C508

C510

JC14

C519

C512

C501

C513

R672

JC913

R526

R55

6 C504

R91

6

R91

4

R91

5

R54

4

JC911

R671

C516C515R521

R522

JC932 JC933

JC934

R517

JC935

JC936

JC938

JC23

R673

C502

C514 JC16

R505 R504

R596

R598

JC24

JC914

R57

0

R52

9

JC912

C509

R674R519

JC17

R597

R53

6

JC38

R802 R803

JC811

C815C816

R891

R819R820

C814

R818

C812

JC810

R890

C810

C811

C890

R815R800

JC907R814

C808

C809

C807

C805

IC802IC801

C802C801

R917

R926

CN351

JC18

R636

R563

R564

R923 R924

R533

L402 L409

C418

C401

JC906JC904

R902

R903

C417C405

IC803

R910

R509

X501

S103

Q664

C403

R568

D502

C951

D804

C819

D801

D802

IC804

R55

9

D503

IC501


CDX-GT410U/GT414U4-7. PRINTED WIRING BOARD KEY SECTION : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13

1-872-032-

1-872-032- (11)

11

1-872-033- (11)

11

1-872-033- (11)

11

(11)

11

LED846,946,S903SOURCE

M >

SEEK+

LSW901LED861864,LED961963

(RING ILLUMINATION)

LED843,943,S902

SEEK

LSW902

OFF

LED844,944,S904EQ3

LED845,945,S906PTY

1/GP/ALBM 2/GP/ALBM+ 5 6/PAUSE AF/TA

PUSH SELECT(VOLUME)

RE901

AUXJ901

DSPL/DIM

IC971

MODE

LED847,947,S907

LED850,950,S908

LED851,951,S909

LED852,952,S910

LED853,953,S911

LED854,954,S912

LED855,955,S913

LED856,956,S914

LED857,957,S915

3/REP 4/SHUF

LED841,941,S901

AMAIN BOARD CN370

1 2

5 4 3

LED842,942(CD INDICATOR)

LED

944

LED943LED843

LED

863

LED961

LED

862

LED864

LED

846

LED

946

LED

847

R904

LED

947

LED842LED942

LED

850

LED

950

LED

851LE

D95

1

LED

852

LED

845

LED

952

S908 S909

S903

S902

LED

853L

ED95

3

LED

854

S907

LED

945

LED

856

LED

956

LED

857

LED

957

LED941LED841

R909

LED861

LED9

63

LED9

62IC971

S906

S904

S910

R85

4R

954

R947R847

R96

1

R86

1

R86

2R

843R943

R906R907

R908

R90

2

R903

C974 R977R853

R953

LSW902

S915

LSW901

LED

844

S901

S911 S912 S913 S914

LED

954

LED

855L

ED95

5

1

2

3

4

CN902

ORG

RED

FB90

1FB

903

FB90

2

BRN

ORG

RED

BRN

R98

9

C981

R98

8

C982

R90

1

C992

C975

D906 D95

3D90

4

D903

R971

R88

8

R88

9

R887

C976

R978

R98

4

R98

3

C979

R85

0R

950

R91

0

CN901

Q882Q881 Q883

R911

FB90

7

FB906C991

R84

9R

949

R95

1

R85

1

R91

2

R95

2R

852

R914

R915

R96

2

R848R948

R946R846

R84

5

R94

5

R94

4

R84

4

R905

D971 R97

6

R975

R864 R863

Q991 Q992

R922

R921

D907

R91

3

C977

R98

2

R942 R842

R841

R941

R981

D905

D908 FB904FB905

R99

3

R994R995

LF90

1

D95

1

D95

5

R881 R882R

886

R883R885R884

IC972

C905

RB901

FL901FLUORESCENT INDICATOR TUBE

CN90

2

RE901

(Page 20)

LED844 B-2LED845 C-2LED846 B-4LED847 C-4LED850 D-5LED851 D-6LED852 D-7LED853 D-8LED854 D-8LED855 D-9LED856 D-10LED857 D-11LED861 B-3LED862 B-2

Ref. No. Location

D903 I-10D904 I-9D905 I-10D906 I-10D907 I-10D908 H-9D971 H-4

IC971 D-4IC972 I-11

LED841 A-13LED842 B-7LED843 A-1

Semiconductor LocationRef. No. Location

LED863 B-3LED864 C-3LED941 A-13LED942 B-7LED943 A-2LED944 B-2LED945 C-2LED946 B-4LED947 C-4LED950 D-5LED951 D-6LED952 D-7LED953 D-7LED954 D-8

Ref. No. Location Ref. No. Location

LED955 D-9LED956 D-10LED957 D-11LED961 B-3LED962 C-3LED963 C-2

Q881 I-8Q882 I-8Q883 I-9Q991 I-6Q992 I-6


CDX-GT410U/GT414U

4-8. SCHEMATIC DIAGRAM KEY SECTION

R901 R904

R978

R984R983

R909

R850R950

R910

Q882

Q881

Q883

R911

R849R949

R951 R851

R912

R952 R852

R914 R915

R954

R962

R961

R943

R948

R946

R945

R906 R907 R908

R944

R902 R903

R977R976

R975

R913

R982

R953

R881

R886

R883

R885

R884

IC972R941

R942

R947

R841

R842

R843

R844

R845

R846

R847

R848

R853

R854

R861

R862

FB905

FB904

C905

FB902

FB901

FB903

S901

S902

S903

S904

LSW

901(

2/2)

LSW

902(

2/2)

S907

S908

S909

S910

S911

S912

S913

S914

S915

S906

R922 R921

C974C975

C976

C977

C979

C982

C981

Q991Q992

C992 C991

IC971

R971

FB906

FB907

R905

R88

2

R88

7

R88

8

R88

9

R994

R993

R995

LSW901(1/2)

LSW902(1/2)

R863

R864

FL901RE901

CN901

CN902

J901

LED941

LED942

LED943 LED843

LED945

LED842

LED841

LED944 LED844

LED947

LED845

LED847

LED846LED946

LED950 LED850

LED953

LED951 LED851

LED952 LED852

LED954

LED955 LED855

LED854

LED956

LED963

LED962

LED856

LED853

LED957 LED857

LED961

LED861

LED863

LED862

LED864

D97

1

R981

D904

D903

D908

D906

D907

D905

D951 D953

D95

5

LF901

RB901

R989R988

(Page 22)


CDX-GT410U/GT414U

IC BLOCK DIAGRAMS

IC300 TDA8588AJ/N2/R1/M5 (AEP, UK MODEL) (MAIN Board (1/3))IC300 TDA8588AJ/N2/R1 (RUSSIA MODEL) (MAIN Board (1/3))

MUT

EM

UTE

ENABLELOGIC

STANDBY/MUTE

BATTERYDETECTION

CHIP DETECT/DIAGNOSTIC

PROTECTION/DIAGNOSTIC

SWITCH

REGU

LATO

R

SWITCH

REFERENCEVOLTAGE

LOADDUMPPROTECTION

TEMPERATUREPROTECTION

BACK-UPSWITCHREGULATOR

1

3

5

7

9

11

13

15

17

19

21

23

25

27

29

31

33

35

37

2

4

6

8

10

12

14

16

18

20

22

24

26

28

30

32

34

36

TAB

OUT-FL-

OUT-FL+

OUT-RL-

OUT-RL+

IN-RL

S-GND

IN-RR

OUT-RR+

OUT-RR-

OUT-FR+

OUT-FR-

DIAG

ANT-REM

AMP-REM

SERVO5V

MECH6V

VP

B.UP+B

SDA

SCL

VP2

PGND3

SVR

IN-FL

IN-FR

BEEP

PGND2

VP1

STB

PGND1

RST

CRES

AUDIO8.3V

GND

PANEL+B

CBU

FL

RL

RR

VP

FR

I2C BUS

IC601 BA8271F-E2 (MAIN Board (1/3))

1

2

3

456

7 8

9

10

14

131211

BUS ONSWITCH

RESETSWITCH

BATTERYSWITCH

BUS ON

RST

BATT

CLKVREF

GND

VCC

RESETBUS ONCLK INBU IN

DATA IN

DATA OUT

DATA

IC401 BD3442FS-E2 (MAIN Board (2/3))

1

2

BUS-RCH

100k

100k

100k

100k

100k

100k

250k

250k

250k

BUS-LCH

TU-RCH 3

4TU-LCH

5CD-RCH

6CD-LCH

7AUX-RCH

8AUX-GND

9AUX-LCH

10DS3-L

11DS1-L

12DS2-L

13EBIAS

14DS2-R

15DS1-R

16DS3-R

26 OUT-FR

27 VCCVCC

VCC2

28 MUTE

29 SCL

30 SDA

31 GND

32 F2L

INPUTSELECTOR

VOLUME1/MUTE

VOLUME2

I2CBUS

LOGIC

TREBLE/BASS

/MIDDLE

SPECTRUMANALYZER

FADER

25 OUT-FL

24 OUT-RR

23 OUT-RL

FADER

FADER

22 SUBOUT-R

21

20

SUBOUT-L

19

ADJ

18

SAOUT

17

SADA

SACLK

FADER

FADER

LPF

EFFECT

INPUTGAIN

FADER

27

CDX-GT410U/GT414U

IC50 TDA7333013TR (MAIN Board (2/3))

VDDA

INTERPOLATOR

RAMBUFFER

&CONTROL

LOGIC

TEST LOGIC&

PIN MUX'S

I2C/SPI

INTERFACE

BAND PASSFILTER

SIGMA DELTACONVERTER

SINC4FILTER

REF3

REF2

REF1

VSS

VDDD

RESETN

TM

1

MPX16

CSNSDAOUT

RDSREG

3

INTNM

PX

SINC

4REG

SDAINSCKSPITESTREG

14

2

3

4

5

6

7

8

INTN15

SA_DATAOUT13SDA_DATAIN12SCL_CLK11

OSCILLATOR

XTO10

XTI9

RDSDEMODULATOR &

SYNCHRONIZATION

2

IC801 NJM2387ADL3 (MAIN Board (3/3))IC802 NJM2387ADL3 (MAIN Board (3/3))

1 2 3 4 5

CURRENTLIMIT

THERMALPROTECTION

OVERVOLTAGEPROTECTION

BANDGAPREFERENCE

VIN CONTROL VOUT VADJ GND

28

CDX-GT410U/GT414U

IC803 BD9778HFP (MAIN Board (3/3))

1 2 3 4 5

CURRENTLIMIT

PWMCOMPARATOR

ERRORAMP

L:OFFH:ON

VREF

VINTSD

OSC

VIN SW PB GND INV6

RT7

EN

VREFSOFTSTART

ON/OFF

LATCH

DRIVER

RESET

29

CDX-GT410U/GT414U

IC PIN DESCRIPTIONIC501 MB90F046PF-G-101E1 (SYSTEM CONTROL) (MAIN BOARD (3/3))

Pin No. Pin Name I/O Pin Description

1 AREASEL0 I Destination setting pin 0



4 B-OUTSEL I Black-out with/without discrimination signal input H: Black-out

5 DIAG I Status signal input from power amplifier

6 AAC SEL I AAC play setting signal input

7 BEEP O Beep signal output to power amplifier

8 AMPSTB O Standby signal output to power amplifier

9 VOLATT O Electronic volume attenuate control signal output

10 FSW IN I D/D converter oscillator frequency count signal input

11 VSS Ground pin

12 TUATT O Tuner mute control signal output

13 NSMASK O Noise mask signal output

14 ILLUMI SEL I Illumination voltage setting signal input

15 COL SEL I Two colors change setting signal input

16, 17 NCO O Not used. (Open)

18 FL CS O Fluorescent indicator tube chip select signal output

19 FL SO O Fluorescent indicator tube serial data signal output

20 FL SCK O Fluorescent indicator tube serial clock signal output


23 VCC5 Power supply pin (+3.3 V)

24 EEP SIO I/O EEPROM bus serial data signal input/output

25 EEP CKO O EEPROM bus serial clock signal output

26 RDS ON O RDS (Radio Data System) on signal output Tuner on: L

27 MC RX I Mechanism microcomputer comunication signal input RX

28 MC TX O Mechanism microcomputer comunication signal output TX


31 RE IN0 I Rotary encoder signal input 0

32 RE IN1 I Rotary encoder signal input 1

33 I2C SCK O I2C bus serial clock signal output

34 I2C SIO I/O I2C bus serial data signal input/output

35 DAVDD A/D converter power supply pin (+3.3 V)

36 AVRH A/D converter external reference power supply pin (+3.3 V)

37 DAVSS Ground pin

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEYIN1 I Key signal input 1

41 KEYIN0 I Key signal input 0

42 VSS Ground pin

43 RCIN0 I Rotary commander key signal input Not used in this set.

44 to 47 NCO O Not used. (open)

48 AD ON O A/D converter power supply control signal output

49 MD0 I Operation mode setting pin (Connect to VDD.)

50 MD1 I Operation mode setting pin (Connect to VDD.)

51 MD2 I Operation mode setting pin (Connect to VSS.)

52 KEYACK I Key acknowledgment detect signal input

53 TUATTIN I Tuner mute zero cross detect signal input

54 BUIN I Back-up power supply detect signal input

30

CDX-GT410U/GT414U

55 NCO O Not used. (Open)

56 DAVN I RDS (Radio Data System) data block synchronized detect signal input


58 UNISI I SONY bus data signal input

59 UNISO O SONY bus data signal output

60 UNISCK O SONY bus clock signal output

61 Z MUTE I Mute signal input

62 NOSE SW I Front panel attachment detect signal input L: With panel, H: Without panel

63 FLASH W IMemory mode change signal input Normally H: Single chip mode, after reset

L: flash write mode

64 SIRCS I Remote control signal input

65 to 70 NCO O Not used. (Open)

71 RC IN1 I Rotary commander shift key signal input Not used in this set.

72 to 74 NCO O Not used. (Open)

75 FSW OUT OD/D converter oscillator frequency shift control signal output

L: 350 kHz, H: 415 kHz


77 RESET I CPU reset signal input

78 NCO (OPEN REQ) O Not used. (Open)

79 XIN I Low speed operation clock signal input (32.768 kHz)

80 XOUT O Low speed operation clock signal output (32.768 kHz)

81 VSS1 Ground pin

82 OSCIN I High speed operation clock signal input (18.432 MHz)

83 OSCOUT O High speed operation clock signal output (18.432 MHz)

84 VCC3 Power supply pin (+3.3 V)

85 CYRIL SEL I Cyril correspondence discrimination signal input L: No correspondence

86 DEMOSEL I DEMO select signal input H: DEMO on, L: DEMO off


88 SYSRST O System reset signal output

89 FL ON O Fluorescent indicator tube power on/off control signal output

90 DD ON O D/D converter power on/off control signal output

91 USB OVER I USB overcurrent detection signal input L: Overcurrent detection

92 USB ON O USB overcurrent detection IC control signal output H: On, L: Off

93 WAKE UP O Mechanism microcomputer wake up signal output H: Wake up, L: Sleep

94 CDON I CD mechanism servo power supply control request signal input

95 CDMON I CD mechanism deck power supply control request signal input

96 BUSON O Bus on signal output

97 TESTIN I Test mode detect signal input

98 TELATT I Telephone attenuate detect signal input

99 ACC IN I Accessory power supply detect signal input

100 ATT O Audio mute control signal output

Pin No. Pin Name I/O Pin Description

31


EXPLODED VIEWS

1 X-2149-438-1 PANEL (FL-U) ASSY, SUB2 3-042-244-11 SCREW (T)3 X-2108-670-1 LOCK ASSY (S)4 2-050-124-01 SCREW +BTT 2.6X55 A-1215-203-A MAIN BOARD, COMPLETE (AEP,UK)

5 A-1221-474-A MAIN BOARD, COMPLETE (RU)6 2-021-848-01 SHEET (TU), GROUND7 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)

F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10ATU1 A-3220-961-B TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)

#4 7-685-794-09 SCREW +PTT 2.6X10 (S)#5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT#6 7-621-284-40 SCREW +P 2.6X10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE: The mechanical parts with no reference

number in the exploded views are not supplied. Items marked * are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

-XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinets Color Accessories are given in the last of this parts list.

5-1. MAIN SECTION

R R

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

not supplied

not supplied

not supplied

F901

not supplied

TU1

not supplied

not supplied

#1

#1

#1

#3

#4

#4

#5

#6

#3

#4

#2

#1

MG-101U-188//Q

A

A

B

B

1

2

3

4

7

6

A

5

AbbreviationRU: Russia model

32

CDX-GT410U/GT414U

51 A-1215-205-A PANEL COMPLETE ASSY, FRONT(GT410U:AEP,UK)

51 A-1215-215-A PANEL COMPLETE ASSY, FRONT(GT414U:AEP,UK)

51 A-1226-240-A PANEL COMPLETE ASSY, FRONT (GT410U:RU)51 A-1228-536-A PANEL COMPLETE ASSY, FRONT (GT414U:RU)52 X-2149-754-1 BUTTON ASSY (S) (GT410U)

52 X-2149-755-1 BUTTON ASSY (S) (GT414U)53 X-2149-758-1 PANEL (SV) ASSY, FRONT (GT410U)53 X-2149-759-1 PANEL (SV) ASSY, FRONT (GT414U)54 X-2149-353-1 KNOB (VOL) (SV) ASSY

55 2-693-599-01 SPRING (RELEASE)56 2-686-937-01 PANEL (FL-U), BACK57 3-250-543-21 SCREW (+B P-TITE M2)58 X-2149-228-2 CASE ASSY (for FRONT PANEL)59 2-686-941-01 HOLDER (USB)

60 2-686-945-01 CAP (USB)61 3-251-320-01 EMBLEM (NO. 2.5), SONYCN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENTRE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)


5-2. FRONT PANEL SECTION

58

59FL901CN902

not supplied(KEY board)

not supplied

not supplied

not supplied

not supplied

not suppliednot supplied(AUX board)

51

52

53

60

54

55

56

57

57

RE901

61

33

CDX-GT410U/GT414U

101 A-1177-168-A MECHANICAL BLOCK ASSY102 A-1177-169-A DAXEV//Q

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)104 2-626-869-01 SCREW (M2X3), SERRATION

105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK107 A-1206-357-A SERVO BOARD, COMPLETE#7 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE3


5-3. CD MECHANISM SECTION(MG-101U-188//Q)

NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.

not supplied

#6#6

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

101

102

103

105

104

107

106not supplied 106

Ver. 1.1

34


ELECTRICAL PARTS LIST

AUX BOARD**********

< FERRITE BEAD >

FB901 1-414-595-11 INDUCTOR, FERRITE BEADFB902 1-414-595-11 INDUCTOR, FERRITE BEADFB903 1-500-245-11 INDUCTOR, FERRITE BEAD

< JACK >

J901 1-819-732-21 JACK (DIA. 3.5) (AUX)*************************************************************

KEY BOARD**********

< CAPACITOR >

C905 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC974 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC975 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC976 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC977 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V

C979 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC982 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC991 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC992 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

< CONNECTOR >

CN901 1-820-620-11 PLUG, CONNECTOR 24P

< DIODE >

D903 8-719-057-80 DIODE MA8180-M-TXD904 8-719-057-80 DIODE MA8180-M-TXD905 8-719-977-12 DIODE DTZ6.8BD906 8-719-977-12 DIODE DTZ6.8BD907 8-719-977-12 DIODE DTZ6.8B

D908 8-719-977-12 DIODE DTZ6.8BD951 1-804-988-21 VARISTOR, CHIP (1608)D953 1-804-988-21 VARISTOR, CHIP (1608)D955 1-804-988-21 VARISTOR, CHIP (1608)D971 8-719-420-90 DIODE MA8051-M

< FERRITE BEAD >

FB904 1-469-876-11 INDUCTOR, FERRITE BEADFB905 1-469-876-11 INDUCTOR, FERRITE BEAD

FB906 1-216-295-11 SHORT CHIP 0FB907 1-216-295-11 SHORT CHIP 0

< FLUORESCENT INDICATOR TUBE >

FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT

< IC >

IC971 6-600-163-01 IC RS-770 (IR)IC972 6-706-715-01 IC NJM2867F33(TE2)

< DIODE >

LED841 8-719-078-21 LED SML-310PTT86 (Z)LED842 8-719-078-21 LED SML-310PTT86 (CD INDICATOR)LED843 8-719-078-21 LED SML-310PTT86 (OFF)LED844 8-719-078-21 LED SML-310PTT86 (EQ3)LED845 8-719-078-21 LED SML-310PTT86 (PTY)

LED846 8-719-078-21 LED SML-310PTT86 (SOURCE)LED847 8-719-078-21 LED SML-310PTT86 (MODE)LED850 8-719-078-21 LED SML-310PTT86 (DSPL/DIM)LED851 8-719-078-21 LED SML-310PTT86 (1/GP/ALBM)LED852 8-719-078-21 LED SML-310PTT86 (2/GP/ALBM+)

LED853 8-719-078-21 LED SML-310PTT86 (3/REP)LED854 8-719-078-21 LED SML-310PTT86 (4/SHUF)LED855 8-719-078-21 LED SML-310PTT86 (5)LED856 8-719-078-21 LED SML-310PTT86 (6/PAUSE)LED857 8-719-078-21 LED SML-310PTT86 (AF/TA)

LED861 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED862 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED863 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED864 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED941 8-719-053-09 LED SML-310VTT86 (Z)

LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR)LED943 8-719-053-09 LED SML-310VTT86 (OFF)LED944 8-719-053-09 LED SML-310VTT86 (EQ3)LED945 8-719-053-09 LED SML-310VTT86 (PTY)LED946 8-719-053-09 LED SML-310VTT86 (SOURCE)

LED947 8-719-053-09 LED SML-310VTT86 (MODE)LED950 8-719-053-09 LED SML-310VTT86 (DSPL/DIM)LED951 8-719-053-09 LED SML-310VTT86 (1/GP/ALBM)LED952 8-719-053-09 LED SML-310VTT86 (2/GP/ALBM+)LED953 8-719-053-09 LED SML-310VTT86 (3/REP)

LED954 8-719-053-09 LED SML-310VTT86 (4/SHUF)LED955 8-719-053-09 LED SML-310VTT86 (5)LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE)


NOTE: Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.

-XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

Items marked * are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

SEMICONDUCTORSIn each case, u : , for example:uA.. : A.. uPA.. : PA..uPB.. : PB.. uPC.. : PC.. uPD.. : PD..

CAPACITORSuF : F

COILSuH : H

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

KEYAUX

AbbreviationRU: Russia model

35

CDX-GT410U/GT414U

LED957 8-719-053-09 LED SML-310VTT86 (AF/TA)LED961 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED962 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED963 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)

< COIL >

LF901 1-457-223-11 COIL, COMMON MODE CHOKE

< SWITCH >

LSW901 1-798-018-11 SWITCH, TACTILE (WITH LED)(M > SEEK +)

LSW902 1-798-018-11 SWITCH, TACTILE (WITH LED)(. m SEEK )

< TRANSISTOR >

Q881 8-729-600-22 TRANSISTOR 2SA1235-FQ882 8-729-600-22 TRANSISTOR 2SA1235-FQ883 8-729-600-22 TRANSISTOR 2SA1235-FQ991 6-550-752-01 TRANSISTOR DTC614TKT146Q992 6-550-752-01 TRANSISTOR DTC614TKT146

< RESISTOR >

R841 1-216-810-11 METAL CHIP 120 5% 1/10WR842 1-216-810-11 METAL CHIP 120 5% 1/10WR843 1-216-811-11 METAL CHIP 150 5% 1/10WR844

Documents

CDX-GT410U/GT414U - ESpecarchive.espec.ws/files/SONY CDX-GT410U_GT414U.pdf · Power requirements 12 V DC car battery ... To control CD/radio/MD/USB, the same as (SEEK) ... CDX-GT410U/GT414U