Catalog ASA CONS 2014 s

8/10/2019 Catalog ASA CONS 2014 s

1/100

b

a

c

3%

peste 500 structuri prefabricatepeste 300.000 m 3 de beton prefabricat

peste 3.000.000 m2

construiiover 500 precast structures

over 300,000 m 3 precast concreteover 3,000,000 m 2 built

Prefabricate din beton armat i precomprimatReinforced and prestressed concrete elements


2/100


3/1003

Prezentarea companiei / About the company

ISTORICASA CONS ROMNIA SRL a luat fiin n anul 1999 ca parte aGrupului ASA Kft. Ungaria, devenind n scurt timp liderul pieeiromneti n domeniul prefabricatelor din beton armat pen-

tru construcii nerezideniale. n decursul anilor ASA CONS aacumulat o experien considerabil n construcia de centrecomerciale i logistice, depozite, lucrri de infrastructur, con-strucii industriale i civile.

n 2008 ASA CONS devine parte a Grupului Consolis, lider eu-ropean n livrarea soluiilor n domeniul construciilor, lucr-rilor civile i infrastructurii feroviare, specializat n produciaelementelor din beton cu performane nalte. Cu aproximativ10.000 de angajai care opereaz n 30 de ri din ntreagalume, n special n Europa i regiunea mediteranean, Grupula generat venituri de 1,3 miliarde Euro n 2013. Inovaia areun rol central n activitatea Consolis. Grupul dezvolt conti-nuu materiale, produse i procese de producie inovatoare cuscopul mbuntirii eficienei i calitii. Cu peste 100 de anide experien, Grupul Consolis a devenit sinonim cu soluiileinovatoare de ultim generaie.

Intrarea n Consolis a nsemnat pentru ASA CONS un pas marespre viitor, acces la tehnologii de vrf i o infuzie de know-howde la cei mai buni specialiti n domeniu.

EVOLUIA N CIFRE/INVESTIIICreterea investiiilor n domeniu, precum i dotrile cu utilajei echipamente moderne, au dus la creterea produciei i a

capacitii de montaj. n 2008 acestea au atins cifre record:40.000 m3 de beton prefabricat, iar cifra de afaceri a depit40 milioane Euro. Pn n prezent, ASA CONS a executat peste500 structuri prefabricate pentru construcii civile i indus-triale, care nsumeaz peste300.000 m3 de beton prefabri-cat, echivalnd aproximativ3.000.000 m2 construii.

ASIGURAREA CALITIICalitatea materialelor i a produselor finite este o preocuparepermanent a companiei. Se verific n permanen calitateabetoanelor puse n oper la realizarea elementelor prefabri-cate. Elementele prefabricate executate au certificate de con-

formitate, obinute n urma testelor realizate n laboratorulpropriu, laborator de grad II, dotat cu aparatur necesar efec-turii acestor ncercri.

HISTORY ASA CONS ROMANIA SRL was founded in 1999 as part of thegroup ASA Kft. Hungary and has quickly become the marketleader in precast concrete for non residential buildings in Ro-

mania. ASA CONS built an impressive track record over theyears, including commercial and logistic centers, warehouses,infrastructure, civil and industrial buildings.

In 2008 ASA CONS became part of Consolis Group, a leadingEuropean Group in building solutions, civil works and rail in-

frastructure, specialized in manufacturing high-performanceconcrete building elements. With around 10,000 employeesoperating in 30 countries throughout the world, mostly in Eu-rope and the Mediterranean region, the Group generated 1.3billion in revenue in 2013. Innovation plays a central role inConsolis activities. The Group is continually developing newand innovative materials, products and manufacturing pro-cesses in order to improve productivity and quality. With over100 years of experience Consolis Group has become synony-mous with latest generation innovative solutions.

Joining Consolis Group meant for ASA CONS a big step in the future, access to cutting-edge technology and know-how infu-sion from the best specialists in the field.

FACTS AND FIGURES/INVESTMENTSThe company has consistently made investments in its equip-ment, leading to an increased production and assembly ca-

pacity. In 2008, record numbers were achieved: 40,000 m 3 of

precast concrete and an annual turnover of over 40 million. Todate, ASA CONS has produced over 500 precast structures forcivil and industrial projects, totalling more than 300,000 m 3 of precast concrete , for a total of about 3,000,000 m 2 built .

QUALITY ASSURANCE The quality of materials and finished products is an ongoing

priority for the company, who is constantly assessing the qual-ity of the concrete used for precast elements. The precast el-ements hold certificates of compliance, obtained from testsconducted in our Grade II laboratory, well equipped for suchtests.

ASA CONSs management is focused on the quality of productsand services, aiming daily to exceed the standards to which the

Anul nfiinrii /Founding year : 1999Intrarea n Consolis / Joined Consolis : 2008


4/1004

company is certified: ISO 9001:2008 for quality, ISO 14001: 2004 for environment and OHSAS 18001: 2007 for healthand safety.

GRADE 2 LABORATORY

ASA CONSs grade 2 laboratory is authorized by State Inspec-torate in Constructions and functions under reference standardSR EN ISO / IEC 17025. The laboratory is equipped with allnecessary equipment and follows environmental conditionsspecified in European standards. This certification authorizesus to conduct determinations both for own products, as wellas for third parties , for the following profiles:

1. BBABP Concrete, reinforced and prestressed concrete Making concrete specimens Preservation samples - tests for hardened concrete Bulk density - tests for hardened concrete

Bulk density of fresh concrete granularity aggregates con-tained in the concrete mix

Preliminary tests Workability (consistency) Compressive strength - tests for hardened concrete Temperature - tests for fresh concrete Setting time - fresh concrete testing

2. M.B.M. Materials for concrete and mortar The appearance and shape of granules - tests for natural

river aggregates Humus content Grading curve. Grading analysis by sieve tests Dry and wet bulk density Determination of bulk density. Tests for aggregates


Managementul ASA CONS acord o atenie deosebit calit-ii produselor i serviciilor oferite, urmrind zilnic depireastandardelor asumate prin certificarea sistemelor de manage-ment al calitiiISO 9001:2008, de mediuISO 14001: 2004 i al sntii i securitii n muncOHSAS 18001:2007.

LABORATOR DE GRAD II

Laboratorul de gradul II al ASA CONS este autorizat de ctreInspectoratul de Stat n Construcii i funcioneaz conformstandardului de referin SR EN ISO/CEI 17025, fiind dotat cuechipamentele necesare i respectnd condiiile de mediu pre-cizate n standardele europene. Aceast certificare ne autori-zeaz s efectum determinriatt pentru propriile produse,ct i pentru teri, pentru urmtoarele profile:

1. BBABP beton, beton armat i beton precomprimat Confecionare epruvete beton Conservare probe ncercri pentru beton ntrit Densitate aparent - ncercri pentru beton ntrit Densitate aparent a betoanelor n stare proaspt Granulozitatea agregatelor coninute n amestecul de beton ncercri preliminare Lucrabilitatea (consistena) Rezistena la compresiune ncercri pentru beton ntrit Temperatura ncercri pentru beton proaspt Timp de priz ncercri pentru beton proaspt

2. M.B.M. Materiale pentru betoane i mortare Aspectul i forma granulelor ncercri pentru agregate na-

turale, de ru Coninut de humus

Curba granulometric. Analiza granulometric prin cernere Densitatea n grmad n stare uscat i n stare de umidi-tate natural


5/1005

Additive solution density Floating particles in aggregates Cements strength: 2 days, 7 days, 28 days Cement stability (volume constant). Tests for cement Conservation status - tests for cement Setting time for cement

Aggregates humidity Average values b/a and c/a of granules with dmin> 7.1 mm Organoleptic testing

The testing are performed to improve the quality of services ,in accordance with documented procedures and requirementsset by our customers. No deviations are accepted and preven-tive measures are taken to eliminate non-quality, along theidentification and registration of all non-compliances relatedto quality and achievement of corrective and preventive ac-tions.

Processes covered: Collecting Preservation of samples Identifying samples Sampling Technical process procedures - specific to each type of test Registration

Advantages of grade 2 laboratory ASA CONS: Professional and experienced staff, licensed by the Inspec-

torate State in Construction Tests performed according to European standards Certificate issuance, recognized in the field as the test report Develop cumulative bulletin paper Preparation and verification of concrete recipes Specialized technical assistance for improving recipes

COMPLETE SERVICES ASA CONS is aone-stop-shop partner , supplier of high qual-ity products and customized services. The company offers avariety of products for precast concrete structures: foundationelements, intermediate floor elements, precast roof, wall pan-els and columns, as well as infrastructure solutions: beams,culvert elements, soundproof panels.

Determinarea masei volumice n vrac. ncercri pentru agre-gate

Densitatea soluiei de aditivi Pri levigabile din agregate Rezistene mecanice la cimenturi: la 2 zile, 7 zile, 28 zile Stabilitatea cimentului (constan de volum). ncercri pen-

tru ciment Starea de conservare ncercri pentru ciment Timpul de priz al cimentului Umiditatea agregatelor Valori medii b/a i c/a ale granulelor cu dmin> 7.1 mm Verificarea organoleptic

ncercrile sunt efectuate cu scopul mbuntirii calitiiserviciilor, conform procedurilor documentate stabilite i ce-rinelor clienilor, neadmindu-se abateri de la acestea i lu-ndu-se msuri pentru prevenirea non-calitii, identificarea i nregistrarea tuturor neconformitilor referitoare la calitate irealizarea aciunilor corective i preventive.

Procese reglementate: Recoltare Pstrarea probelor Identificarea probelor Eantionare Proceduri Tehnice de Proces specifice pentru fiecare tip

de ncercri nregistrare

Avantajele laboratorului de grad II ASA CONS: Personal de specialitate, cu experien, autorizat de Inspec-

toratul de Stat n Construcii ncercri efectuate conform standardelor europene Emiterea documentelor de atestare, recunoscute n dome-

niu, sub forma raportului de ncercare Elaborarea buletinelor cumulative pe lucrare ntocmirea i verificarea reetelor de beton Asisten tehnic de specialitate pentru mbuntirea re-

etelor

SERVICII COMPLETEASA CONS este unpartener complet, un furnizor de produsecalitative i servicii adaptate cererilor fiecrui client. Compania

v ofer pentru structurile prefabricate din beton armat: ele-mente de fundare, elemente de planeu intermediar, elementeprefabricate de acoperi, panouri i stlpi, precum i soluii ninfrastructur: grinzi de pod, elemente de podee, panouri fo-noabsorbante.



6/1006

ASA CONS producegama complet de elemente din beton

armat i precomprimat, oferind n acelai timp i servicii-le adiacente pe care le implic ridicarea unei structuri, de lacentre comerciale sau logistice la construcii industriale saupoduri.

AVANTAJELE PRODUSELOR ASA CONS:- toate produsele noastre respect ntru totul standardele ilegislaia n domeniu privind: rezistena n timp, rezistena lafoc, rezistena la factorii de mediu

- ncorporeaz materie prim de cea mai bun calitate i teh-nologie performant

- fabricarea elementelor presupune o serie de procese rigurosdefinite astfel nct produsul finit va corespunde celor maimari pretenii de calitate

- elementele prefabricate executate sunt verificate n laborato-rul propriu; n urma acestei verificri se emite certificatul deconformitate al produsului

AVANTAJELE CLIENILOR ASA CONS:- one stop shop- garania final a lucrrii- timp redus de la proiectare la execuie i montaj; posibili-tatea avansrii construciei pe timp de iarn, pn la -20C

- costuri mai mici dect o construcie clasic- evitarea problemelor cu intermediarii, ntruct echipele noas-

tre de montaj pun n oper elemente deja cunoscute, produseconform acelorai standarde de calitate, n mod tradiional

PROIECTAREPrimul pas n crearea elementelor prefabricate l reprezintproiectarea corect a acestora. Echipa de proiectani preia in-formaiile de la beneficiarul final i le transform n planuriconcrete, astfel nct produsul finit s corespund pe deplinnevoilor clienilor notri. Aceast echip includeprofesioniticu experiena necesar prentmpinrii oricror potenialepiedici n ridicarea efectiv a structurilor din prefabricate. Pu-nem la dispoziia beneficiarilorconsultan de specialitate ndomeniu.

ASA CONS manufactures and provides the full range of reinforced and prestressed concrete elements , as well as the

services related to raising a structure, from commercial anddistribution centres to industrial buildings and bridges.

ASA CONS PRODUCT BENEFITS:- All our products fully comply with standards and legislation

on: resistance over time, fire resistance, resistance to envi-ronment factors

- Made with high quality raw materials and high technology - The manufacturing process consists of a series of rigorous

steps so the finished product will meet the highest qualityrequirements

- Precast elements are tested in our laboratory; following this

examination a certificate of conformity of the product is is-sued

ASA CONS OFFERS TO ITS CLIENTS:- One stop shop- Final work warranty - Reduced time from design to fabrication and installation, al-

lowing for construction in temperatures as low as -20C - Lower costs than with a traditional building- No third parties, as our installation teams work with already

known items, produced according to the same standards

DESIGNThe first step in creating precast elements is correct and ac-curate design. The design department takes information fromthe final beneficiary and turns it into blueprints, so that the

finished product fully meets our clients needs. The depart-ment includes experienced professionals , able to preventany potential obstacles in the effective elevation of precaststructures. We also provide specialized consulting for ourcustomers.

Oferta companiei /Company offer

Soluii complete marca ASA CONSComplete solutions by ASA CONS


7/1007

EXECUTIONThe company can produce precast elements needed for the

fast elevation of slender structures with large span, with amaximum post-to-post distance of 36 m. Up to now, 300,000m3 of precast concrete left our factory for sites across thecountry, for a total of about 3,000,000 m 2 built.

LOGISTICS ASA CONS providesadequate transport for normal and over-sized elements, including columns and beams with a length of26 or 30 m. We partner with 15 transportation companies ex-

perienced in the transportation of regular and oversized loads.

For lifting on site, the company is equipped with 70- and 80-ton Liebherr cranes and 80-ton Tadano Faun crane, as well asManitou erecting platforms.

ASSEMBLY ASA CONS has professional installation teams, with extensiveexperience in the field. ASA CONS has executed over 500 pre-cast structures for civil and industrial construction . The com-

pany can manage projects that include the entire structuralbuild - the precast elements as well as the monolithic build.

A common extension of our mandate is bringing the projectto the building envelope, inclusive of enclosures. At times, wehave acted as the general contractor for the entire project,as it has been the case of the pharmaceutical center RichterGedeon in Targu Mures.

EXECUIEASA CONS are capacitatea de a produce elementele prefabrica-te necesare ridicrii n scurt timp de structuri zvelte, cu deschi-dere mare, permind o distan maxim ntre stlpi de pnla 36 m. Pn n prezent 300.000 m3 de beton prefabricat auieit pe poarta fabricii spre antiere din ntreaga ar, echiva-lnd aproximativ 3.000.000 m2 construii.

LOGISTICAASA CONS asigur printr-o logistic adecvattransportul ele-mentelor cu dimensiuni normale i gabarit depit, inclusivstlpi i grinzi cu lungimea de 26 sau 30 m, avnd un porto-foliu tradiional de 15 companii cu care colaboreaz, fiecarespecializat n transportul elementelor normale i cu gabaritdepit. Pentru ridicarea on site, compania are n dotare auto-macarale tip LIEBHERR de 70 i 80 tone i tip TADANO FAUN cucapacitatea de 80 tone, precum i platforme autoridictoareMANITOU.

MONTAJASA CONS dispune de echipe de montaj formate din profe-sioniti cu o experien vast n domeniu. Pn acum, ASACONS a executat peste 500 de structuri prefabricate pentruconstrucii civile i industriale. De asemenea, echipele coor-doneaz i lucrri care duc la realizarea cldirii n concept destructur la rou, respectiv ntreaga structur de rezisten,att componentele prefabricate, ct i structura monolit.

O extindere uzual o reprezint realizarea cldirii la nivel deanvelop, inclusiv nchideri, uneori extinzndu-ne competen-ele pn la asigurarea antreprizei generale a unei construc-ii, ca exemplu execuia centrului farmaceutic Richter GedeonTrgu Mure.

Oferta companiei /Company offer


8/1008

Lucrri de referin - centre comerciale /Reference works - commercial centers

Armonia - 2 magazine /2 stores

Baumax - 5 magazine /5 stores

Anul construciei /Construction year : 2007-2008Suprafaa total /Total area : 90 000 m2



9/1009



Cora - 4 magazine /4 stores

Dedeman - 22 magazine / 22 stores



10/10010


Jupiter Piteti

Anul construciei /Construction year : 2008Suprafaa / Area: 55 000 m2

Anul construciei /Construction year : 2008-2009Suprafaa / Area: 61 000 m2

Era Shopping Park Oradea


11/10011



Kaufland - 27 magazine /27 stores

Kika Bucureti



12/10012


Obi Sibiu



Metro Cash & Carry - 19 magazine /19 stores


13/10013




Penny Market - 22 magazine /22 stores

Polus Cluj-Napoca


14/10014



Real Hypermarket - 5 magazine /5 stores

Praktiker - 5 magazine /5 stores



15/10015

Lucrri de referin - centre comerciale, construcii industriale /Reference works - commercial centers, industrial buildings

Anul construciei /Construction year : 2006-2013Suprafaa / Area : 47 000 m 2

Bosch Blaj

Centru Comercial Trgu Jiu

Anul construciei /Construction year : 2013-2014Suprafaa / Area : 31 000 m 2


16/10016

Lucrri de referin - construcii industriale /Reference works - industrial buildings


Continental Timioara

Calsonic Kansei Ploieti



17/10017

Lucrri de referin - construcii industriale / Reference works - industrial buildings


Emerson Cluj - 5 fabrici /5 factories

Egger Rdui



18/10018


Holzindustrie Schweighoffer Baco Comneti


Anul construciei /Construction year : 2013Suprafaa total /Total area : 16 000 m2

Emerson Oradea - 1 fabric /1 factory


19/10019


Ina Schaeffler Braov



Huf Arad - hal producie / production hall


20/10020


Makita Brneti - 3 fabrici /3 factories



Kronospan Braov


21/10021


Plexus Oradea


MGI Coutier Ghiroda



22/10022

Lucrri de referin - depozite logistice /Reference works - logistic warehouses

Aramis Baia Mare


Bucharest West Logistic Park



23/10023


Gedeon Richter Trgu-Mure



Dacia Renault Piteti


24/10024


Log Center - 2 depozite /2 warehouses



Lidl Iernut


25/10025

Lucrri de referin - depozite logistice, construcii civile /Reference works - logistic warehouses, civil buildings

Ansamblu rezidenial Sibiu /Residential buildings Sibiu

Anul construciei /Construction year : 2014Suprafaa / Area: 630 m2

Rewe Turda



26/10026

Ansamblu rezidenial Cluj-Napoca /Residential buildings Cluj-Napoca


Lucrri de referin - construcii civile /Reference works - civil buildings

Piaa agroalimentar Rogerius Oradea / Rogerius marketplace Oradea



27/10027

Lucrri de referin - lucrri infrastructur /Reference works - infrastructure works

Anul construciei /Construction year : 2007

Pasaj Iulius Mall /Iulius Mall passage Cluj-Napoca

Pasaj Polus Center / Polus Center passage Cluj-Napoca



28/10028



Pod Snpaul / Sanpaul bridge

Poduri peste rul Some / Bridges over river Somes



29/10029


oseaua de centur / Beltway Cluj-Napoca

Autostrada Transilvania / Transilvania highway

Anul construciei /Construction year : 2009-2010



30/10030

Lucrri de referin /Reference works


31/100


32/100

ASA CONS ROMNIA SRLStr. 22 Decembrie 1989 nr. 27401113 Turda RomniaTel. +40 264 312 765 Fax +40 264 317 [email protected] www.asacons.ro www.consolis.ro


33/100

peste 500 structuri prefabricatepeste 300.000 m 3 de beton prefabricat

peste 3.000.000 m2

construiiover 500 precast structures

over 300,000 m 3 precast concreteover 3,000,000 m 2 built

Prefabricate din beton armat i precomprimatReinforced and prestressed concrete elements


34/100


35/100

Construcii industriale - produse

Industrial buildings - products

31


36/10032

Produse - Elemente de fundare /Products - Foundation elements

Pahare / Pocket foundations

Din structura fundaiei pahar se execut prefabricat gulerul, care transportat n antier se rotete cu 180 n plan vertical, dup care se leag pe mustiarmtura tlpii paharului i se monteaz pe poziie.Eliminnd manopera n antier i timpul de maturizare a betonului, viteza demontaj a structurii crete considerabil.

From the structure of the pocket foundation the collar is precast executed; onsite it is vertically rotated by 180 degrees, then the plate reinforcement is con-nected on stubs and assembled in position.By eliminating labor on site and concrete maturation time, the erection speedof the structure rises considerably.

Vedere 3D /3D view


37/10033

Produse - Elemente de fundare /Products - Foundation elements

Nr. crt. a b e h

1 0.90 0.90 0.25 1.10

2 1.20 1.20 0.25 1.10

3 1.30 1.30 0.25 1.10

4 1.50 1.50 0.30 1.10

5 1.50 2.30 0.30 1.10

6 1.60 2.60 0.30 1.10

1 - egalizare2 - talp monolit3 - pahar prefabricat

1 - equalization2 - monolithic base3 - precast pocket foundation

Dimensiuni /Dimensions

Seciune caracteristic /Specific section


38/10034

Produse - Stlpi /Products - Columns

Stlpi / Columns

Lungimile stlpilor variaz ntre 5 i 24 m. /The column length varies between 5 and 24 m.

Stlpii prefabricai sunt executai ntr-o varietate de dimensiuni, forme i lun-gimi. Suprafaa betonului este neted, iar muchiile sunt teite. n general stl-pii necesit o seciune transversal minim de 300 x 300 mm, care asigur obun conexiune cu grinzile, o manipulare uoar, precum i o rezisten la focde 120 minute fcndu-i potrivii pentru o gam larg de construcii. The columns are made in a variety of dimensions, shapes and lengths. Thesurface of the concrete is smooth and the edges are beveled. Generally thecolumns require a minimum cross section of 300 x 300 mm that ensures agood connection with the beams, an easy handling and a 120 minutes fireresistance, making them suitable for a large range of construction.

Vedere 3D /3D view


39/10035

a

b

Produse - Stlpi /Products - Columns

Nr. crt. a b

1 0.25 0.25

2 0.40 0.40

3 0.50 0.50

4 0.54 0.60

5 0.60 0.60

6 0.70 0.70

7 0.80 0.80

8 0.80 1.20




40/10036

Produse - Elemente prefabricate de acoperi /Products - Roof precast elements

Grinzi I drepte / Straight I beams

Lungimea poate varia de la 12 la 27 m. /Lenght can vary between 12 and 27 m.

Vedere 3D /3D view

Grinzile principale se execut cu seciune constant sau seciune variabilfuncie de soluia de scurgere a apelor de pe acoperi. La rndul lor ambeletipuri pot avea seciunea transversal I sau T funcie de deschiderea halei i ncrcrile la nivelul acoperiului, iar mbinarea acestora cu stlpii structuriieste de tip uscat.

The main beams are executed with constant or variable section dependingon the solution of draining water of the roof. Both types can have I or T crosssection depending on the halls opening and loads at the roof level. The con-nection with the structures columns is made by dry mechanical fixing.


41/10037


Capt /End Coam /Ridge

Seciuni caracteristice /Specific sections

Vedere lateral /Side view


42/10038


Grinzi 30 m I n dou ape /30 m I beams


Vedere 3D /3D view




43/10039

15

9 7

2 0

5 2

15

30

60

1 1 9

60

30

135858

523 523

9 0

2 0

5 3

1 4 5

2 3

5 8


Pant 3% /Slope 3%Pant 3% /Slope 3%





44/10040


Grinzi T drepte / Straight T beams


Vedere 3D /3D view




45/10041


Nr. crt. a

1 0.18

2 0.20

3 0.23





46/10042

Produse - Elemente prefabricate de acoperi / Products - Roof precast elements

Grinzi T n dou ape /T beams


Vedere 3D /3D view




47/10043

1 0 5

Pant 3% /Slope 3% Pant 3% /Slope 3%






48/10044


Pane seciune T /T section purlins

Panele se execut n special n variant precomprimat cu seciuni trapezoi-dale sau T. Lungimea lor i mbinarea cu restul structurii se stabilete n partepentru fiecare structur.

Purlins can be made also prestressed with trapezoidal or T section. The lengthand the connection with the rest of the structure are determined separately

for each structure.

Vedere 3D /3D view



49/10045


a b c d

0.30-0.50 0.14-0.20 0.31-0.61 0.10-0.30





50/10046


Pane trapez / Trapezoidal purlins

Vedere 3D /3D view


Panele se execut n special n variant precomprimat cu seciuni trapezoi-dale sau T. Lungimea lor i mbinarea cu restul structurii se stabilete n partepentru fiecare structur.

Purlins can be made also prestressed with trapezoidal or T section. The lengthand the connection with the rest of the structure are determined separately

for each structure.


51/10047





52/10048


Grinzile de planeu servesc ca suport pentru plcile constituen-te ale planeului. Pe aceste elemente se pot rezema fii cu go-luri, predale i alte elemente de planeu. Prin alctuirea acestor ele-mente se poate asigura continuarea pe reazeme n suprabetonare.

Floor beams are used as support for constituent slabs of the floor. On theseelements hollow core slabs, filigrames and other floor elements can be rest.Using floor beams, bearings extension in over concreting can be assured.

Vedere 3D /3D view

Produse - Elemente de planeu intermediar /Products - Intermediate floor elements

Grinzi de planeu / Floor beams


53/10049


a b

0.40-0.80 0.40-0.80




a

b


54/10050


Elemente TT /TT elements


Acest tip de elemente se folosete pentru planee ncrcate cu sarcini maripn la deschideri de 17 m. Capacitatea portant a acestora se proiecteazdup necesiti prin dimensionarea suprabetonrii. Variaia dimensionrilorse poate asigura prin limea plcii laterale, respectiv nlimea i limeanervurilor.

This type of elements are used for slabs loaded with high loads up to 17 mspans. Their bearing capacity is designed according to requirements by dimen-sioning of the over concreting. The variation of the correct dimensioning canbe assured by the width of side slab, respectively height and width of the ribs.

Vedere 3D /3D view


55/10051





56/10052


Fii cu goluri - FGP 200 /Hollow core slabs - FGP 200

Aceste produse sunt executate cu tehnologie de beton extrudat pe piste continuede 90 m cu debitare la lungime dup necesitile proiectantului. Sunt executatedin beton C50/60 i cu armare exclusiv cu toroane dup o conformare rezulta-t din dimensionare. nlimea seciunilor produse la ASA sunt de 20 i 32 cm.

These products are executed with extruded concrete technology on 90 m con-tinuous tracks with cut to length according to designers needs. They are ex-ecuted of C50/60 concrete with reinforcing exclusively with strands accordingto a sizing calculation. Sections produced at ASA CONS are of 20 and 32 cm.

Vedere 3D /3D view


57/10053

n c r c

r i a d m

i s e , v a

l o r i c a r a c t e r

i s t i c e

P e r m

i s s i

b l e l o a d

, c h a r a c

t e r i s t

i c v a

l u e s

[ d a N

/ m 2 ]



H(mm)

I(mm)

TIPCod

produsNumrtoroane

Diametrutoron (mm)

200 1200

FGP-200/A 69.3FGP-200/B 8

FGP-200/C 612.9

FGP-200/D 8

t o r o a n e

s t r a n

d s

toroane strands

(section area)(volume/meter)(weight/meter)(point/meter)(total weight)(density/m 3 )

Deschidere Opening


58/10054



Vedere 3D /3D view




59/10055

H(mm)

I(mm)

TIPCod

produsNumrtoroane

Diametrutoron (mm)

320 1200

FGP-320/A 5+2

12.9FGP-320/B 7+2

FGP-320/C 8+2

FGP-320/D 11+2



toroane strands

toroane strands

5 buc TBP 12.9-1860 (12.9)Pk=110 kN

7 buc TBP 12.9-1860 (12.9)Pk=110 kN

8 buc TBP 12.9-1860 (12.9)Pk=110 kN

11 buc TBP 12.9-1860 (12.9)Pk=110 kN

FGP-320/A

FGP-320/B

FGP-320/C

FGP-320/D

volum/metru: V=0.1993 m3/mlmasa/metru: M=478.32 kg/mlrost/metru: m=33.6 kg/ml

densitate/m 33: 24.00 kN/m

FGP-320

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

A (7 TBP-12,90)B (9 TBP-12,90)

C (10 TBP-12,90)D (13 TBP-12,90)

6559

90510251280

45510

665765970

31011

485565740

20012

350420565

11513

245305430

14

160210325

15

135235

16

165

(section area)(volume/meter)(weight/meter)(point/meter)(total weight)

(density/m 3 )

n c r c

r i a d m

i s e , v a


i s t i c e

P e r m

i s s i

b l e

l o a d

, c h a r a c

t e r i s t

i c v a

l u e s

[ d a N

/ m 2 ]

Deschidere Opening


60/10056


Predale / Filigrames

Vedere 3D /3D view


Sunt elementele componente pentru planee la care prin suprabetonare serealizeaz o structur cu planeu mixt. Acestea au rol de cofraj i de obiceitrebuie sprijinite pe durata turnrii i maturizrii suprabetonrii.

These products are component elements for floors whereat by over concretingis achieved a monolith floor. These elements have formwork function and usu-ally must be supported during casting period and over concreting maturation.


61/10057



suprafa rugoasrough surface



62/10058

Produse - Panouri de faad i grinzi de soclu /Products - Facade panels and cap beams

Vedere 3D /3D view

Panourile prefabricate pot fi interioare de tip antifoc i exterioare de tiptristrat. Acestea la rndul lor sunt panouri de soclu i panouri curente. Di-mensiunile panourilor sunt limitate de posibilitatea manipulrii i trans-portului. Fixarea lor de structur se face cu mbinri sudate sau nurubate.

Precast panels can be interiors type fire resistant and exteriors type tri layerwhich at their turn can be socle panels and current panels. The dimensions ofthe panel are limited by the possibility of manipulation and transport. The set-ting with the structure is made by screwed or welded joints.

Not: vezi i panourile grafice de la pagina 66.Note: see also the graphic panels on page 66.

Panouri de faad monostrat i tristrat - beton aparent / Monolayer and trilayerconcrete facade panels - exposed concrete


63/10059


Tip/mrime H max L max b1 t b2

Panou tristrat 4.8 m 15 m 12-16 cm 6-8 cm 7-10 cm

Panou monostrat 4.8 m 15 m 12-35 cm - -





64/10060

Produse - Trepte prefabricate beton armat /Products - Precast concrete staircase

Vedere 3D /3D view

Trepte prefabricate beton armat / Precast concrete staircase

Scara prefabricat din beton armat este un element de construcie care asi-gur legtura pe vertical ntre diferite etaje ale cldirii. Dintre avantajeleprefabricrii sistemului de trepte merit menionate: dimensiunile exacte,forma perfect i identic a elementelor proiectate, gama variat de realizarea acestora n funcie de necesitile clientului, precum i reducerea timpuluide execuie pe antier prin eliminarea timpului necesar realizrii cofrajului.

The precast concrete staircase is a construction element that provides verticalconnection between different floors of the building. Among the advantages ofconcrete prefabricating system worth mentioning: size precision, perfect sha-

pe and identical elements, designed for a wide range of projects, depending oncustomer needs and reducing execution time on site by eliminating the timerequired to complete the shuttering.


65/10061

Produse - Trepte prefabricate beton armat /Products - Precast concrete steps

d

AA


Not: dimensiunea variaz n funcie de specificul proiectului. /Note: size varies depending on the type of the project.


h

ab

l


66/10062


67/10063

Construcii civile - produse

Civil buildings - products


68/10064

Informaii utile /Useful information


69/10065

Informaii utile /Useful information

Analiz comparativ a planeelor / Concrete slab benchmarking

Avantajele produselor prefabricate /Precast concrete products advantages

Timp de execuie i montaj redus, fiind independentde condiiile meteorologice

Performance and reduced installation time, it doesnot depend on the weather

Cost redus de execuie i montaj Lower costs for manufacturing and assembly

Pot lua orice forme i dimensiuni Any shape or size

Calitate superioar n producie, datorit controluluipermanent din fabric

High quality production due to permanent producti-on control

Elementele prefabricate se livreaz pe antier cu cer-tificate de conformitate

Prefabricated elements are delivered on site withcompliance certificates

Asigur protecie termic, fonic, mpotriva apei ia focului

Resistant to most external factors thermal, sound,water, fire

Elementele prefabricate sunt durabile; rezistena lorcrete gradual n timp

Prefabricated elements are durable; their resistancegradually increases over time

Utilizare mai buna a spaiului construit datorit des-chiderilor mari a elementelor prefabricate

Better use of space built through large openings prefabricated elements

Indicator / Indicator FGP + suprabetonare /Hollow concrete slab Planeu monolit / Monolithic slab

lei/m2 lei/m2Fabricaie /Production 83Transport /Transport 15

Pre montaj /Installation price 27Macara /Crane inclus da nu

Cofraj /Framework nu 80 manoper + materialArmare /Reinforcement 22 4kg/m2, 8/20 91 17kg/m2, 28/10

Folie /Foil nu daBetonare /Casting 24 8 cm 45 15 cm, manoper + material

Finisaj /Finishing 11 1 strat tinci nu necesit alte straturiGrosime /Thickness 25-45 cm 15 cm

Timp /Time 40 m2/h 5 m2/hPersonal /Personnel 4 6

Fono/Termo /Phonic/Thermal da nuTotal costuri /Total costs 182 mai economic i mai rapid 216


70/10066

Panouri grafice / Graphic panels

Sectorul comercial /Commercial sector

Produse - Panouri grafice /Products - Graphic panels

Panourile grafice sunt unprodus prefabricat nou, unicat n Romnia, careofer plusvaloare proiectelor dumneavoastr. Prin crearea unor suprafee tex-turate cu undesign original la alegere, acestea vor transforma o simpl con-strucie ntr-o oper de art. Nu exist limite n dimensiunea i tipul designuluisau imaginii unice utilizate n crearea texturii panourilor grafice. ASA CONS estesingurul productor din Romnia care deine tehnologia deproducie i v poate oferi acest tip de panouri. Ele sunt realizate dup o teh-nologie de ultim generaie, originar din Finlanda. Metoda utilizat are cai rezultat o suprafa texturat, neted sau complet expus. Textura de pesuprafa este rezultatul contrastului dintre faa panoului i expunerea finisa- jului agregat. Aceasta este o metod eficient din punct de vedere al costurilor,finisajul agregat fiind folosit n faza de producie a elementelor de beton..

Aplicabilitatea panourilor grafice este similar cu cea a panourilor de faad,ele putnd fi implementate ntr-o gam variat de tipuri de construcii, dela construcii civile i industriale la lucrri de infrastructur, att pentruexterior, ct i pentru interior.

Prin utilizarea panourilor grafice vei obine o faad cu stil la un pre rezonabil.

Panourile grafice sunt: Cu mult stil i la un pre rezonabil Durabile i uor de ntreinut Testate i sigure

Panourile grafice nseamn noi posibiliti arhitecturale i o nou modalitatede finisare a construciilor.Singura limit este imaginaia!

The graphic panels are a new precast product, unique in Romania , providingadded value to your projects. By creating textured surfaces with an original design of choice , they will turn a simple design into a work of art. There areno limits on the size and type of design or single image graphic panels usedto create texture.

ASA CONS isthe only producer in Romania holding production technologyand capability to provide this type of facade panels. They are created usingcutting-edge technology, originally from Finland. The method used results in a patterned, smooth or completely exposed surface. The pattern on the surfaceresults from the contrast between the fairface and the exposed fine aggregate finish. This is a cost-effective, tested and safe method because traditional exposed fine aggregate materials and processes are used in the manufacturingof concrete elements.

The applicability of graphical panels is similar to the facade panels; they canbe implemented in a wide range of building types, from civil and industrialbuildings to infrastructure works , both for exterior and interior projects.

Graphic concrete offers the chance to produce a stylish facade at a reason-able price.

Graphic concrete is: Stylish and reasonably priced Durable and easy to maintain Tested and safe

Graphic concrete offers new building possibilities and a new way of finishingconstructions. Imagination is your only limit!


71/100


Sectorul industrial /Industrial sector

Sectorul rezidenial /Residential sector Sectorul ambiental /Environmental sector

Sectorul public /Public sector



72/100


Fii cu goluri - FGP 200 / Hollow core slabs - FGP 200



Vedere 3D /3D view

6867


73/10069



H(mm)

I(mm)

TIPCod

produsNumrtoroane

Diametrutoron (mm)

200 1200

FGP-200/A 69.3FGP-200/B 8

FGP-200/C 612.9

FGP-200/D 8

t o r o a n e

s t r a n

d s

toroane strands

(section area)(volume/meter)(weight/meter)(point/meter)(total weight)(density/m 3 )

n c r c

r i a d m

i s e , v a


i s t i c e

P e r m

i s s i

b l e l o a d

, c h a r a c

t e r i s t

i c v a

l u e s

[ d a N

/ m 2 ]

Deschidere Opening


74/10070



Vedere 3D /3D view




75/10071

H(mm)

I(mm)

TIPCod

produsNumrtoroane

Diametrutoron (mm)

320 1200

FGP-320/A 5+2

12.9FGP-320/B 7+2

FGP-320/C 8+2

FGP-320/D 11+2



toroane strands

toroane strands

FGP-320

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

A (7 TBP-12,90)B (9 TBP-12,90)

C (10 TBP-12,90)D (13 TBP-12,90)

6559

90510251280

45510

665765970

31011

485565740

20012

350420565

11513

245305430

14

160210325

15

135235

16

165

5 buc TBP 12.9-1860 (12.9)Pk=110 kN

7 buc TBP 12.9-1860 (12.9)Pk=110 kN

8 buc TBP 12.9-1860 (12.9)Pk=110 kN

11 buc TBP 12.9-1860 (12.9)Pk=110 kN

FGP-320/A

FGP-320/B

FGP-320/C

FGP-320/D

volum/metru: V=0.1993 m3/mlmasa/metru: M=478.32 kg/mlrost/metru: m=33.6 kg/ml

densitate/m 33: 24.00 kN/m

(section area)(volume/meter)(weight/meter)(point/meter)(total weight)

(density/m 3 )

n c r c

r i a d m

i s e , v a


i s t i c e

P e r m

i s s i

b l e

l o a d

, c h a r a c

t e r i s t

i c v a

l u e s

[ d a N

/ m 2 ]

Deschidere Opening


76/10072

Vedere 3D /3D view

Produse - Trepte prefabricate beton armat /Products - Precast concrete staircase

Trepte prefabricate beton armat / Precast concrete staircase

Scara prefabricat din beton armat este un element de construcie care asi-gur legtura pe vertical ntre diferite etaje ale cldirii. Dintre avantajeleprefabricrii sistemului de trepte merit menionate: dimensiunile exacte,forma perfect i identic a elementelor proiectate, gama variat de realizarea acestora n funcie de necesitile clientului, precum i reducerea timpuluide execuie pe antier prin eliminarea timpului necesar realizrii cofrajului.

The precast concrete staircase is a construction element that provides verticalconnection between different floors of the building. Among the advantages ofconcrete prefabricating system worth mentioning: size precision, perfect sha-

pe and identical elements, designed for a wide range of projects, depending oncustomer needs and reducing execution time on site by eliminating the timerequired to complete the shuttering.


77/10073

Produse - Trepte prefabricate beton armat /Products - Precast concrete steps

d

AA



h

ab

l



78/10074


Predale / Filigrames

Vedere 3D /3D view


Sunt elementele componente pentru planee la care prin suprabetonare serealizeaz o structur cu planeu mixt. Acestea au rol de cofraj i de obiceitrebuie sprijinite pe durata turnrii i maturizrii suprabetonrii.

These products are component elements for floors whereat by over concretingis achieved a monolith floor. These elements have formwork function and usu-ally must be supported during casting period and over concreting maturation.


79/10075






80/10076


Panourile prefabricate pot fi interioare de tip antifoc i exterioare de tiptristrat. Acestea la rndul lor sunt panouri de soclu i panouri curente. Di-mensiunile panourilor sunt limitate de posibilitatea manipulrii i trans-portului. Fixarea lor de structur se face cu mbinri sudate sau nurubate.

Precast panels can be interiors type fire resistant and exteriors type tri layerwhich at their turn can be socle panels and current panels. The dimensions ofthe panel are limited by the possibility of manipulation and transport. The set-ting with the structure is made by screwed or welded joints.

Not: vezi i panourile grafice de la pagina 66.Note: see also the graphic panels on page 66.

Vedere 3D /3D view

Panouri de faad monostrat i tristrat - beton aparent / Monolayer and trilayerconcrete facade panels - exposed concrete


81/10077


Tip/mrime H max L max b1 t b2

Panou tristrat 4.8 m 15 m 12-16 cm 6-8 cm 7-10 cm

Panou monostrat 4.8 m 15 m 12-35 cm - -





82/10078


Grinzile de planeu servesc ca suport pentru plcile constituen-te ale planeului. Pe aceste elemente se pot rezema fii cu go-luri, predale i alte elemente de planeu. Prin alctuirea acestor ele-mente se poate asigura continuarea pe reazeme n suprabetonare.

Floor beams are used as support for constituent slabs of the floor. On theseelements hollow core slabs, filigrames and other floor elements can be rest.Using floor beams, bearings extension in over concreting can be assured.

Vedere 3D /3D view


Grinzi de planeu / Floor beams


83/10079


a b

0.40-0.80 0.40-0.80




a

b


84/10080


Elemente TT /TT elements

Acest tip de elemente se folosete pentru planee ncrcate cu sarcini maripn la deschideri de 17 m. Capacitatea portant a acestora se proiecteazdup necesiti prin dimensionarea suprabetonrii. Variaia dimensionrilorse poate asigura prin limea plcii laterale, respectiv nlimea i limeanervurilor.

This type of elements are used for slabs loaded with high loads up to 17 mspans. Their bearing capacity is designed according to requirements by dimen-sioning of the over concreting. The variation of the correct dimensioning canbe assured by the width of side slab, respectively height and width of the ribs.

Vedere 3D /3D view



85/10081





86/1008282


87/10083

Infrastructur - produse

Infrastructure - products


88/10084

Grinzi de pod 42 i 52 cm /Bridge beams 42 and 52 cm

Produse - Grinzi de pod /Products - Bridge beams


Vedere 3D /3D view

Grinzile de pod sunt asimilate din gama de produse IPTANA pentru diferitedeschideri i sarcini, cu seciune I i T, cu deschideri ntre 10 i 12 metri. Pro-dusele fiind de catalog, suport modificri i adaptri n limita acceptrii aces-tora de ctre proiectani.

Bridge beams are assimilated from the IPTANA products range for variousspans and loads, with I and T sections, with spans between 10 and 12 meters.

As catalogue products can be modified and adapted in the acceptance limitof the designers.


89/10085


Dispunere toroane /Strands layoutSeciune caracteristic /Specific sectionSeciune transversal /Cross section


L (m) ncrcare admis

Valoare caracteristic(kN/ml)

6 61

8 3610 23

L (m) ncrcare admis


10 30

12 19.5

19 1922

5

2

5

7

7

0 2

5

531521

52 60

5

14

5 4 2

5

3

5

0 3

5

3

5 5 5 5 5 5 5 56 644

60

7 4 4 7

22

5

7 4 4 722

5 5 5 5 5 5 56 644

60

19 1922

53152

152

60

5 5

5

2

5

7

7

0 2

5 1

2 5

5

3

5

0 4

5

3

Grind de pod 42 / 42 Bridge beam Grind de pod 52 / 52 Bridge beam


90/10086



Vedere 3D /3D view






91/10087

R = 5 R = 5

92

851 125 25

R = 5 R = 5

Produse - Grinzi de pod / Products - Bridge beams



L (m) ncrcare admis


14 40.5

16 25.5

92

851 1 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5

25 25

3 5

8 0

5 8

4 8 8 2

8 5

2 5

5

3

3 5

8

335 335

102 42 429102

9

4 427 R =

5

R = 5

R = 5

R = 5

Grind de pod 72 / 72 Bridge beam


92/10088



Vedere 3D /3D view






93/10089

118

4

4

5 5 5 5 5

4 4 5

40 4010

R = 1 0

10

1 0 2 1 0

2 4 5

1 2

118

1 0 3

50 75 5 5 5

44

5 5 5 5 7 5

R = 2 0 R = 2 0

R = 1 0

18



L (m) ncrcare admis


18 42.5

21 27.524 21.5

L (m) ncrcare admis


18 46.5

21 33.524 24.5

42 421010

120

16

R =

1 0

R = 2 0 78

6

1 145

47

8

2 0 1

5

9 3

5

1 2

2 1

120

5

3 9

4 4

5 5 5 5 5 5 5 5

4 5

5 5

5 5

4


Grind de pod 93 / 93 Bridge beam Grind de pod 103 / 103 Bridge beam


94/10090


Vedere 3D /3D view

Vedere de sus /Top view


Grinzi de pod 150 cm /Bridge beams 150 cm

Grinda de pod cu seciune I este un proiect propriu, conceput de ctre proiec-tanii notri de specialitate, pentru nlime de 1.50 m i deschideri cuprinse ntre 30 i 41 m.

The I section bridge beam is an original project designed by our expert design-ers, for a height of 1.50 m and openings varying between 30 and 41 m.



95/10091


L (m) Greutate (tone)/buc

30 37.45

41 51.18




96/10092

Vedere 3D /3D view

Canivouri din beton armat / Reinforced concrete channel elements

Acest tip de elemente prefabricate din beton se folosete pentru protejareaconductelor de ap, liniilor electrice i brei optice din subteran. Se pot realizacarosabile sau necarosabile, drepte sau curbe, simple sau duble, n funcie desolicitarea clientului.

This type of precast concrete elements is used for protection of undergroundwater pipes, electric cables and ber optic lines. The elements can be executed

for carriage way or non-carriage way, straight or curved, single or double, depending on customers request.

Produse - Canivouri /Products - Channel elements


97/10093

d

a b a

c

e

a

a

aba

c

Seciune caracteristic /Specific sectionSeciune transversal /Cross section

ab ba a

e

a

c

ad

ab ba ac

Produse - Canivouri /Products - Channel elements



98/1009494


99/100


100/100

Documents

Catalog ASA CONS 2014 s