C-MAX(CG3478en)09-2009

Feel the differenceFordC-MAXOwner's handbook

The information contained in this publication was correct at the time of going to print. In the interest ofdevelopment the right is reserved to change specifications, design or equipment at any time withoutnotice and without incurring any obligations. This publication, or part thereof, may not be reproducednor translated without our approval. Errors and omissions excepted.

© Ford Motor Company 2009

All rights reserved.

Part number: AM5J-19A321-BDA (CG3478en) 09/2009 20090929114739

E108837

IntroductionAbout this handbook................................5Symbols glossary......................................5Parts and accessories..............................5

Quick startQuick start..................................................8

Child safetyChild seats................................................16Child seat positioning..............................17Booster cushions.....................................19ISOFIX anchor points..............................20Child safety locks....................................20

Occupant protectionPrinciple of operation..............................22Fastening the seat belts........................24Seat belt height adjustment..................25Seat belt reminder..................................26Using seat belts during pregnancy......26Disabling the passenger airbag............26

Keys and remote controlsGeneral information on radiofrequencies..........................................28

Programming the remote control........28Changing the remote controlbattery...................................................28

LocksLocking and unlocking...........................32Keyless entry...........................................34Global opening and closing...................36

Engine immobiliserPrinciple of operation..............................38Coded keys.............................................38Arming the engine immobiliser.............38Disarming the engine immobiliser........38

AlarmPrinciple of operation..............................39Arming the alarm.....................................39Disarming the alarm................................40

SteeringwheelAdjusting the steering wheel.................41Audio control............................................41Voice control............................................42

Wipers andwashersWindscreen wipers.................................43Autowipers...............................................43Windscreen washers.............................44Rear window wiper and washers.........44Adjusting the windscreen washerjets.........................................................45

Headlamp washers................................45Checking the wiper blades...................46Changing the wiper blades...................46

LightingLighting control........................................47Autolamps................................................48Front fog lamps.......................................48Rear fog lamps........................................48Headlamp levelling..................................48Adaptive front lighting system(AFS)......................................................49

Hazard warning flashers........................50Direction indicators.................................50Interior lamps...........................................50Removing a headlamp............................51Changing a bulb......................................52Bulb specification chart..........................58

Windows andmirrorsElectric windows.....................................60Exterior mirrors.........................................61

1

Table of contents

Electric exterior mirrors...........................61Auto-dimming mirror..............................62

InstrumentsGauges.....................................................63Warning lamps and indicators..............65Audible warnings and indicators...........67

Information displaysGeneral information................................69Trip computer..........................................72Personalised settings.............................74Information messages...........................76

Climate controlPrinciple of operation..............................81Air vents.....................................................81Manual climate control...........................82Automatic climate control.....................84Heated windows and mirrors................87Auxiliary heater........................................87Electric sunroof.......................................90

SeatsSitting in the correct position.................93Manual seats...........................................93Head restraints........................................94Electric seats...........................................95Rear seats................................................96Heated seats..........................................101

Convenience featuresSun blinds...............................................103Instrument lighting dimmer..................103Cigar lighter............................................103Auxiliary power sockets.......................104Centre console......................................104Cool box.................................................105Storage compartments........................106

Cup holders............................................107Glasses holder.......................................108Toll reader...............................................108Childminder mirror.................................109CD changer............................................109Auxiliary input (AUX IN) socket............109USB port..................................................110Satellite navigation unit holder..............110Floor mats................................................111

Starting the engineGeneral information...............................112Ignition switch.........................................112Steering wheel lock...............................112Starting a petrol engine.........................112Starting a petrol engine - E85..............113Starting a diesel engine.........................114Keyless starting......................................115Diesel particulate filter (DPF).................116Switching off the engine........................117Engine heater..........................................117

Fuel and refuellingSafety precautions.................................118Fuel quality - Petrol.................................118Fuel quality - E85....................................118Fuel quality - Diesel................................118Catalytic converter.................................119Fuel filler flap............................................119Refuelling.................................................119Refuelling - E85......................................120Fuel consumption..................................120Technical specifications........................120

TransmissionManual transmission.............................122Automatic transmission........................122

2

Table of contents

BrakesPrinciple of operation............................125Hints on driving with ABS.....................125Parking brake.........................................125

Stability controlPrinciple of operation............................126Using stability control............................126

Parking aidPrinciple of operation............................127Using the parking aid............................127

Rear viewcameraPrinciple of operation............................129Using the rear view camera.................129

Cruise controlPrinciple of operation............................132Using cruise control..............................132

Load carryingGeneral information..............................134Luggage covers....................................134Rear under floor storage......................135

TowingTowing a trailer.......................................136Detachable tow ball..............................136

Driving hintsRunning-in..............................................140Cold weather precautions...................140Driving through water...........................140

Emergency equipmentFirst aid kit................................................141Warning triangle......................................141

Status after a collisionFuel cut-off switch.................................142

FusesFuse box locations................................143Changing a fuse....................................143Fuse labels..............................................143Fuse specification chart.......................145

Vehicle recoveryTowing points.........................................150Towing the vehicle on four wheels......151

MaintenanceGeneral information..............................152Opening and closing the bonnet........152Engine compartment overview - 1.6LDuratec-16V (Sigma)/1.6LDuratec-16V Ti-VCT (Sigma)............154

Engine compartment overview - 1.8LDuratec-HE (MI4)/2.0L Duratec-HE(MI4).....................................................156

Engine compartment overview - 1.6LDuratorq-TDCi (DV) Diesel................157

Engine compartment overview - 1.8LDuratorq-TDCi (Lynx) Diesel............159

Engine compartment overview - 2.0LDuratorq-TDCi (DW) Diesel..............160

Engine oil dipstick - 1.6L Duratec-16V(Sigma)/1.6L Duratec-16V Ti-VCT(Sigma).................................................161

Engine oil dipstick - 1.8L Duratec-HE(MI4)/2.0L Duratec-HE (MI4)............161

Engine oil dipstick - 1.6L Duratorq-TDCi(DV) Diesel...........................................162

Engine oil dipstick - 1.8L Duratorq-TDCi(Lynx) Diesel........................................162

Engine oil dipstick - 2.0L Duratorq-TDCi(DW) Diesel.........................................162

Engine oil check.....................................162Engine coolant check...........................163Brake and clutch fluid check...............163

3

Table of contents

Power steering fluid check..................164Washer fluid check................................164Technical specifications........................165

Vehicle careCleaning the exterior............................168Cleaning the interior..............................168Repairing minor paint damage............169

Vehicle batteryUsing booster cables............................170Battery connection points.....................171

Wheels and tyresGeneral information...............................172Changing a road wheel........................172Tyre repair kit..........................................177Tyre care.................................................180Using winter tyres..................................181Using snow chains.................................181Technical specifications........................181

Vehicle identificationVehicle identification plate....................183Vehicle identification number (VIN).....183

Technical specificationsTechnical specifications........................184

TelephoneGeneral information...............................187Telephone setup....................................187Bluetooth setup.....................................188Telephone controls...............................189Using the telephone - VehiclesWithout:Navigation System.............................189

Using the telephone - Vehicles With:Navigation System.............................192

Voice controlPrinciple of operation............................194Using voice control...............................194Audio unit commands..........................195Telephone commands........................206Navigation system commands...........210Climate control commands.................210

ConnectivityGeneral information..............................213Connecting an external device...........214Connecting an external device -Vehicles With: Bluetooth...................214

Using a USB device...............................215Using an iPod.........................................217

Navigation introductionRoad Safety............................................221

Navigation systemGetting started......................................222

AppendicesType approvals......................................224Type approvals......................................224Type approvals......................................224Electromagnetic compatibility............225

4

Table of contents

ABOUT THISHANDBOOK

Thank you for choosing Ford. Werecommend that you take some time toget to know your vehicle by reading thishandbook. Themore that you knowaboutit, the greater the safety and pleasure youwill get from driving it.

Note: This handbook describes productfeatures and options available throughoutthe range, sometimes even before theyare generally available. It may describeoptions not fitted to your vehicle.

Note: Some of the illustrations in thishandbook may be used for differentmodels, so may appear different to yourvehicle. However, the essentialinformation in the illustrations is alwayscorrect.

Note: Always use and operate yourvehicle in line with all applicable laws andregulations.

Note: Pass on this handbook whenselling your vehicle. It is an integral part ofthe vehicle.

This vehicle has received theendorsement of TÜV, the accreditedinternational testing organisation, for itsallergy-friendly properties.

All materials used in the manufacture ofthe interior of this vehicle meet strictrequirements of the TÜV TOXPROOFCriteria Catalogue for Vehicle Interiors byTÜV Produkt and Umwelt GmbH and aredesigned to minimize the risk of allergicreactions.

Additionally an efficient pollen filterprotects the passengers against allergenparticles in the outdoor air.

For more information, contact TÜV atwww.tuv.com.

SYMBOLSGLOSSARY

Symbols in this handbook

WARNING

You risk death or serious injury toyourself and others if you do notfollow the instructions highlighted

by the warning symbol.

CAUTION

You risk damaging your vehicle if youdo not follow the instructionshighlighted by the caution symbol.

Symbols on your vehicle

When you see these symbols, read andfollow the relevant instructions in thishandbook before touching or attemptingadjustment of any kind.

PARTSANDACCESSORIES

Nowyou can be sure that yourFord parts are Ford parts

Your Ford has been built to the higheststandards using high quality Ford OriginalParts. As a result, you can enjoy driving itfor many years.

Should the unexpectedoccur and amajorpart needs replacing,we recommend thatyou accept nothing less than FordOriginalParts.

5

Introduction

The use of Ford Original Parts ensuresthat your vehicle is repaired to itspre-accident condition and maintains itsmaximum residual value.

FordOriginal Partsmatch Ford's stringentsafety requirements and high standardsof fit, finish and reliability. Quite simply, theyrepresent the best overall repair value,including parts and labour costs.

Now it is easier to tell if you have reallybeen given Ford Original Parts. The Fordlogo is clearly visible on the following partsif they are Ford Original Parts. If yourvehicle has to be repaired, look for theclearly visible Ford branding and makesure that only Ford Original Parts havebeen used.

Look for the Ford logo on thefollowing parts

Sheetmetal

• Bonnet

• Wings

• Doors

• Luggage compartment lid or tailgate

E89932

Bumper and radiator grille

• Radiator grille

• Front and rear bumper

E89933

6

Introduction

Exteriormirror

E89934

Glass

• Rear window

• Side glass

• Windscreen

E89935

Lighting

• Rear lamps

• Headlamp

E89936

7

Introduction

QUICKSTART

Instrument panel overview

Left-hand drive

C DA B E F G H I J K

T S R Q P O N M LE78209

8

Quick start

Right-hand drive

E78210

I HG J K C E D F B A

O N M L S Q R P T

Lighting control. See Lighting control (page 47). Front fog lamps. SeeFront fog lamps (page 48). Rear fog lamp. See Rear fog lamps (page48).

A

Headlamp levelling control. See Headlamp levelling (page 48).B

Multi-function lever: Information display controls. Direction indicators. SeeDirection indicators (page 50). Main beam. SeeLightingcontrol (page47).

C

Instrument cluster. SeeGauges (page 63). SeeWarning lamps andindicators (page 65).

D

9

Quick start

Horn.E

Wiper lever. SeeWipers andwashers (page 43).F

Card holder.G

Air vents. See Air vents (page 81).H

Hazard warning flasher switch. SeeHazardwarning flashers (page 50).I

Airbag deactivation indicator. SeeDisablingthepassengerairbag (page26). Parking aid switch. See Using the parking aid (page 127).

J

Start button. See Keyless starting (page 115).J

Heated windscreen switch. See Heatedwindows andmirrors (page87).

K

Heated rear window switch. See Heatedwindows andmirrors (page87).

L

Climate controls. See Climate control (page 81).M

Audio or navigation unit. See separate handbook.N

Heated front seat switch. See Heated seats (page 101).O

Ignition switch. See Ignition switch (page 112).P

Steeringwheel adjustment. SeeAdjustingthesteeringwheel (page 41).Q

Cruise control switches. See Using cruise control (page 132).R

Audio controls. See Audio control (page 41).S

Instrument lighting dimmer. See Instrument lighting dimmer (page 103).T

Airbag

E69213

WARNING

To avoid the risk of death or seriousinjury, never use a rearward facingchild restraint in the front, unless the

air bag is off.

See Child safety (page 16).

See Disabling the passengerairbag (page 26).

10

Quick start

Locking and unlocking

Unlocking the vehicle

E71963

ABC

UnlockA

LockB

Tailgate unlockC

Press the unlock button once to unlockthe vehicle. See Programming theremote control (page 28).

Press and hold the unlock button for threeseconds to unlock the vehicle and openthe windows and sunroof (globalopening)*.

Press the lock button once to activatecentral locking and arm the alarm.

Press the lock button twice within threeseconds to activate double locking andarm the interior sensors.

Press and hold the lock button for threeseconds to lock the vehicle and close thewindows and sunroof (global closing)*.

Press the tailgate unlock button twicewithin three seconds to unlock theluggage compartment.

* only in combination with four electricwindows (in combinationwith two electricwindows, only the sunroof canbeopenedand closed in this way).

Opening the tailgate

E78262

Toopen the luggage compartment, pressthe switch. The driver’s door must beunlocked.

See Locking and unlocking (page32).

Keyless entry

E78276

Passive locking and unlocking requires avalid passive key to be locatedwithin oneof the three external detection ranges.

11

Quick start


E78278

Pull a door handle to unlock all the doorsand the luggage compartment lid anddisarm the alarm.

Locking the vehicle

E87384

E87435

Locking buttons are located on each ofthe front doors and the luggagecompartment lid.

See Keyless entry (page 34).

Adjusting the steeringwheel

WARNING

Never adjust the steering wheelwhen the vehicle is moving.

1

2

2

E95178

3E95179

12

Quick start

WARNING

Make sure that you fully engage thelocking lever when returning it to itsoriginal position.

See Adjusting the steeringwheel(page 41).

Autowipers

E71013

C

A B

Low sensitivityA

OnB

High sensitivityC

SeeWindscreenwipers (page 43).

Autolamps

E73840

The headlamps will come on and go offautomatically depending on the ambientlight.

See Lighting control (page 47).

Manual climate control

Defrosting and demisting thewindscreen

E71382

Heating the interior quickly

E71377

Cooling the interior quickly

E71381

13

Quick start

SeeManual climate control (page82).

Automatic climate control

E78730

E D C

BA

Windscreendefrosting/demisting

A

Toggle mono mode on and offB

Air conditioning OFFC

Recirculated airD

Air conditioning ONE

See Automatic climate control(page 84).

Rear seats

E78062

E78064

See Rear seats (page 96).

14

Quick start

Engineidlespeedafterstarting

The engine may idle at a higher speedthan normal immediately after startingfrom cold.

See Starting the engine (page 112).

Keyless starting

E85766

Press the start button.

See Keyless starting (page 115).

Diesel particulate filter (DPF)

WARNING

Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF

regeneration process creates very highexhaust gas temperatures and theexhaust will radiate a considerableamount of heat during and after DPFregeneration, andafter youhave switchedthe engine off. This is a potential firehazard.

See Diesel particulate filter (DPF)(page 116).

Manual transmission

Selecting reverse gear

E99067

On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.

SeeManualtransmission (page 122).

Automatic transmission

Note:When the engine is started, thebrakepedal and the selector leverbuttonmust be depressed before theselector lever can be moved from thepark position P.

See Transmission (page 122).

Opening the bonnet

Note:On vehicleswith keyless entry, usethe spare key.

SeeOpening and closing thebonnet (page152). SeeKeylessentry(page 34).

15

Quick start

CHILDSEATS

E68916

WARNINGSSecure children that are less than150 centimetres tall or less than 12years of age in a suitable, approved

child restraint, in the rear seat.

Original text according to ECER94.01: ExtremeHazard!Donot usea rearward facing child restraint on

a seat protected by an air bag in front ofit!

Read and follow themanufacturer’sinstructions when you are fitting achild restraint.

Do not modify child restraints in anyway.

Do not hold a child on your lapwhenthe vehicle is moving.

Do not leave unattended children inyour vehicle.

If your vehicle has been involved inan accident, have the child restraintschecked by properly trained

technicians.

Note:Mandatory use of child restraintsvaries from country to country.

Only child restraints certified toECE-R44.03 (or later) have been testedand approved for use in your vehicle. Achoice of these are available from yourDealer.

Child restraints for differentmass groups

Use the correct child restraint as follows:

Baby safety seat

E68918

Secure children that weigh less than 13kilograms in a rearward facing baby safetyseat (Group 0+) in the rear seat.

16

Child safety

Child safety seat

E68920

Secure children that weigh between 13and 18 kilograms in a child safety seat(Group 1) in the rear seat.

CHILDSEATPOSITIONING

Child seat positions

WARNINGSWhen using a child seat with a seat belt, make sure that the seat belt is not slackor twisted.

When you are using a child seat with a support leg, remove the storagecompartment cover and extend the leg to the base of the compartment.

Mass group categoriesSeating positions

IIIIII0+0

22-36 kg15-25 kg9-18 kgUp to 13kg

Up to 10kg

Boosterseat orcushion


Childsafetyseat

Babysafetyseat

Babysafetyseat

U1U1U1XXFront passenger airbagON

UUUUUFront passenger airbagOFF

17

Child safety

Mass group categoriesSeating positions

IIIIII0+0

22-36 kg15-25 kg9-18 kgUp to 13kg

Up to 10kg



Childsafetyseat

Babysafetyseat

Babysafetyseat

UUUUURear seats

U Suitable for universal category child restraints approved for use in this mass group.

X Not suitable for children in this mass group.

U1 Suitable for universal category child restraints approved for use in this mass group.However, we recommend that you secure children in a government approved childrestraint, in the rear seat.

18

Child safety

BOOSTERCUSHIONS

WARNINGSDo not install a booster seat or abooster cushion with only the lapstrap of the seat belt.

Do not install a booster seat or abooster cushionwith a seat belt thatis slack or twisted.

Do not put the seat belt under yourchild’s arm or behind its back.

Do not use pillows, books or towelsto boost your child’s height.

Make sure that your children sit inan upright position.

Secure children that weigh morethan 15 kilograms but are less than150 centimetres tall in a booster

seat or a booster cushion.

CAUTION

When using a child seat on a rearseat, make sure that the child seatrests tightly against the vehicle seat.

It may be necessary to lift or remove thehead restraint. See Head restraints(page 94).

Booster seat (Group2)

E70710

We recommend that you use a boosterseat that combines a cushion with abackrest instead of a booster cushiononly. The raised seating position will allowyou to position the shoulder strap of theadult seat belt over the centre of yourchild’s shoulder and the lap strap tightlyacross its hips.

Booster cushion (Group3)

E68924

19

Child safety

ISOFIX ANCHORPOINTS

WARNINGSUse only ISOFIX child seats werecommend.

Use an anti-rotation device whenusing the ISOFIX system. Werecommend the use of a top tether

or support leg.

When you are using a child seatwitha support leg, remove the storagecompartment cover and extend the

leg to the base of the compartment.

The ISOFIX systemcomprises of two rigidattachment arms on the child restraintthat attach to anchor points on the rearseats, where the cushion and backrestmeet. Tether anchor points may also befitted.

If you want to use the ISOFIX anchorpoints, see your dealer.

E75531

Attaching a child seatwith toptethers

WARNING

Do not attach a tether strap toanything other than the correcttether anchor point.

E78299

Route the tether strap to the anchor point.Tighten the tether strap in line with thechild seat manufacturer's instructions.

CHILDSAFETY LOCKS

WARNING

You cannot open the doors frominside if you have put the child safetylocks on.

Note:On vehicleswith keyless entry, usethe spare key. SeeKeylessentry (page34).

20

Child safety

E78298

Left-hand side

Turn anti-clockwise to lock and clockwiseto unlock.

Right-hand side

Turn clockwise to lock and anti-clockwiseto unlock.

21

Child safety

PRINCIPLEOFOPERATION

Airbags

WARNINGSDo not modify the front of yourvehicle in any way. This couldadversely affect deployment of the

airbags.

Original text according to ECER94.01: ExtremeHazard!Donot usea rearward facing child restraint on

a seat protected by an airbag in front ofit!

Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use

the seat belt properly, can it hold you in aposition that allows the airbag to achieveits optimum effect. See Sitting in thecorrect position (page 93).

Have repairs to the steering wheel,steering column, seats, airbags andseat belts carried out by a properly

trained technician.

Keep the areas in front of theairbags free from obstruction. Donot affix anything to or over the

airbag covers.

Do not poke sharp objects intoareas where airbags are fitted. Thiscould damage and adversely affect

deployment of the airbags.

Use seat covers designed for seatswith side airbags. Have these fittedby a properly trained technician.

Note: You will hear a loud bang and seea cloud of harmless powdery residue if anairbag deploys. This is normal.

Note: Only wipe airbag covers with adamp cloth.

Driverandfrontpassengerairbags

E74302

The driver and front passenger airbagswill deploy during significant frontalcollisions or collisions that are up to 30degrees from the left or the right. Theairbags will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thuscushioning forward body movement.During minor frontal collisions, overturns,rear collisions and side collisions, the driverand front passenger airbags will notdeploy.

Side airbags

E72658

Side airbags are fitted inside the seatbackof the front seats. A label indicates thatside airbags are fitted to your vehicle.

22

Occupant protection

The side airbags will deploy duringsignificant lateral collisions. Only the airbagon the side affected by the collision willdeploy. The airbagswill inflatewithin a fewthousandths of a second and deflate oncontact with the occupants, thusproviding protection for the chest andshoulder areas. During minor lateralcollisions, overturns, front collisions andrear collisions, the side airbags will notdeploy.

Curtain airbags

E75004

Curtain airbags are fitted inside the trimpanels over the front and rear sidewindows. Moulded badges in the B-pillartrim panels indicate that curtain airbagsare fitted to your vehicle.

The curtain airbags will deploy duringsignificant lateral collisions. Only the airbagon the side affected by the collision willdeploy. The airbag will inflate within a fewthousandths of a second and deflate oncontact with the occupants, thusproviding protection for the head. Duringminor lateral collisions, front collisions, rearcollisions, or overturns the curtain airbagswill not deploy.

Seat belts

WARNINGSWear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use

the seat belt properly, can it hold you in aposition to achieve its optimum effect.See Sitting in the correct position(page 93).

Never use a seat belt for more thanone person.

Use the correct buckle for each seatbelt.

Do not use a seat belt that is slackor twisted.

Do notwear thick clothing. The seatbeltmust fit tightly around your bodyto achieve its optimum effect.

Position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap strap

tightly across your hips.

The driver and front passenger seat beltbuckles are fitted with a seat beltpretensioner. Seat belt pretensionershave a lower deployment threshold thanthe airbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.

Status after a collision

WARNING

Seat belts subjected to strain, as aresult of an accident, should berenewed and the anchorages

checked by a properly trained technician.

23

Occupant protection

FASTENINGTHESEATBELTS

E74124

WARNING

Insert the tongue into the buckleuntil a distinct click is heard,otherwise the seat belt will not be

locked correctly.

Pull the belt out steadily. It may lock ifpulled sharply or if the vehicle is on aslope.

To release the belt, press the red buttonon the buckle and let the belt rewindcompletely and smoothly.

E78079

When in use, the rear seat belts shouldbe placed in the belt guides on theoutboard seatbacks.

E74127

WARNING

In order to ensure that the centrebelt works properly, the rearseatback must be correctly

engaged.

Make sure that each seat belt uses thecorrect buckle.

24

Occupant protection

E74125

2

1

3

The retractor for the rear centre seat beltis located in the roof. To fasten the seatbelt, pull it out steadily and engage thesmaller, black tongue in the smaller blackbuckle to the right of the centre seat.

E74126

2

Then pull the larger tongue across the lapand engage it in the larger buckle to theleft of the centre seat.

To release the belt, first press the redbutton on the left buckle and let the beltrewind. If in constant use, the belt can beleft buckled in the right-hand buckle.When not in use, or when folding ormoving the rear seats, the belt should bereleased from the right-hand buckle bypressing the button on the side of thebuckle and letting the belt rewindsmoothly to the retractor in the roof.

E78080

Fold the smaller seat belt tongue backand insert the larger belt tongue into theretaining slot as shown.

SEATBELTHEIGHTADJUSTMENT

E78081

Press the locking control on the heightadjuster and move the pivot so that thebelt rests across the centre of theshoulder.

25

Occupant protection

Lifting the slider slightly while pressing thelocking control makes it easier to releasethe locking mechanism.

SEATBELTREMINDER

WARNING

Theoccupant protection systemwillonly provide optimum protectionwhen you use the seat belt properly.

The seat belt reminder warninglamp illuminates and an audiblewarning will sound if the driver's

seat belt has not been fastened and thevehicle exceeds a relatively low speed. Itwill also illuminate if the driver's seat beltis unfastenedwhen the vehicle ismoving.The audible warning will go off after fiveminutes but the seat belt reminderwarning lamp will remain on until thedriver's seat belt is fastened.

Deactivating the seat beltreminder

See your dealer.

USINGSEATBELTSDURINGPREGNANCY

E68587

WARNING

Position the seat belt correctly foryour safety and that of your unbornchild. Do not use only the lap strap

or the shoulder strap.

Position the lap strap comfortably acrossyour hips and low beneath your pregnantabdomen. Position the shoulder strapbetween your breasts, above and to theside of your pregnant abdomen.

DISABLINGTHEPASSENGERAIRBAG

WARNING

Make sure that the passengerairbag is disabled when using arearward facing child restraint on the

front passenger seat.

E71313

26

Occupant protection

Fitting the passenger airbagdeactivation switch

WARNING

If you need to fit a child restraint ona seat protected by an operationalairbag in front of it, have a

passenger airbag deactivation switchfitted. Ask your dealer for furtherinformation.

Note: The key switch is located in theglove compartment with an airbagdeactivation lamp in the instrument panel.

If the airbag warning lamp illuminates orflasheswhen you are driving, this indicatesamalfunction. SeeWarninglampsandindicators (page 65). Remove the childrestraint and have the system checkedimmediately.

Disablingthepassengerairbag

A BE71312

DisabledA

EnabledB

Turn the switch to position A.

When you switch the ignition on, checkthat the passenger airbag deactivationwarning lamp illuminates.

Enabling thepassengerairbag

WARNING

Make sure that the passengerairbag is enabledwhen you arenotusing a child restraint on the front

passenger seat.

Turn the switch to position B.

27

Occupant protection

GENERALINFORMATIONONRADIO FREQUENCIES

CAUTION

The radio frequency used by yourremote control can also be used byother short distance radio

transmissions (e.g. amateur radios,medical equipment,wirelessheadphones,remote controls and alarm systems). Ifthe frequencies are jammed, you will notbe able to use your remote control. Youcan lock and unlock the doors with thekey.

Note: You could unlock the doors if youpress the buttons on the remote controlunintentionally.

The operating range between yourremote control and your vehicle variesdepending on the environment.

PROGRAMMINGTHEREMOTECONTROL

A maximum of eight remote controls(including any supplied with your vehicle)canbeprogrammed. The remotecontrolsmust remain inside the vehicle during theprogrammingprocedure. Fasten the frontseat belts and close all doors to ensurethat conflicting chimes do not soundduring programming.

Programming a new remotecontrol

1. To programme new remote controlsturn the ignition key to position II fourtimes within six seconds.

2. Turn the ignition to position 0. A tonesounds to indicate that it is nowpossible to programme the remotecontrols for ten seconds.

3. Press any button on a new remotecontrol. A tone will sound asconfirmation.

4. Repeat this last step for all yourremote controls, including youroriginal. Do not remove the key fromthe ignition when pressing the buttonon this remote control.

5. Switch the ignition back on (positionII) or wait for ten seconds withoutprogramming another remote controlto end the key programming. Only theremote controls which you have justprogrammedare nowable to lock andunlock the vehicle.

Reprogramming theunlockingfunction

Note:When you press the unlock buttoneither all the doors are unlocked or onlythe driver’s door and the luggagecompartment lid are unlocked. Pressingthe unlock button again unlocks all thedoors.

Press and hold the unlock and lockbuttons on the remote key simultaneouslyfor at least four seconds with the ignitionoff. The direction indicators will flash twiceto confirm the change.

To return to the original unlocking function,repeat the process.

CHANGINGTHEREMOTECONTROLBATTERY

E107998

Make sure that you dispose ofold batteries in anenvironmentally friendly way.

Seek advice from your local authorityregarding recycling.

28

Keys and remote controls

Remote control with a foldingkey blade

1

E74383

1. Insert a screwdriver as far as possibleinto the slot on the side of the remotecontrol, push it towards the key bladeand remove the key blade.

E74384

2

2. Twist the screwdriver in the positionshown to start separating the twohalves of the remote control.

E743853

3. Twist the screwdriver in the positionshown to separate the two halves ofthe remote control.

CAUTION

Do not touch the battery contacts orthe printed circuit board with thescrewdriver.

4. Carefully prise out the battery with thescrewdriver.

5. Install a newbattery (3VCR2032)withthe + facing downwards.

6. Assemble the two halves of theremote control.

7. Install the key blade.

29


Remote control without afolding key blade

Type 1

E74386

1. Insert a screwdriver into the recess onthe back of the key and remove thekey blade.

2. Release the retaining clips with thescrewdriver and separate the twohalves of the remote control.

CAUTION



4. Install a newbattery (3VCR2032)withthe + facing upwards.



Type2

1

2

E78284

1. Slide the release slider in the directionof the arrow.

2. Remove the key blade.

E105064

3

3. Twist the screwdriver in the positionshown to separate the two halves ofthe remote control.

CAUTION



5. Install a newbattery (3VCR2032)withthe + facing downwards.

30




31


LOCKINGANDUNLOCKING

Central locking

You can only centrally lock the doors ifthey are all closed.

Note: The driver’s door can be unlockedwith the key. This needs to be used if theremote control or keyless entry is notfunctioning.

Note: Central locking also locks andunlocks the fuel filler flap.

Double locking

WARNING

Donot activate double lockingwhenpersons or animals are inside thevehicle. You will not be able to

unlock the doors from the inside if youhave double locked them.

Double locking is a theft protection featurethat prevents someone fromopening thedoors from the inside. You can onlydouble lock the doors if they are all closed.

Locking and unlockingconfirmation

When you unlock the doors, the directionindicators will flash once.

When you lock the doors, the directionindicators will flash twice.

Note: If your vehicle has double locking,the direction indicatorswill only flash twiceonce you have activated double locking.

Locking and unlocking thedoorswith the key

Turn the top of the key towards the frontof the vehicle to lock the door. Turn thetop of the key towards the rear of thevehicle to unlock the door.

Double locking the doorswiththe key

Turn the key to the lock position twicewithin three seconds to double lock thedoors.

Locking and unlocking thedoors and the luggagecompartment lidwith theremote control

E87379

A B C

UnlockA

LockB

Luggage compartment lidunlock

C

Double locking the doors and theluggage compartment lidwith theremote control

Press button B twice within threeseconds.

32

Locks

Locking and unlocking thedoors from inside

Driver's door

A

B

E71958

Lock all doorsA

Unlock all doorsB

Front and rear passenger doors

E98653

To lock the front and rear passengerdoors individually, press the button andclose the door when leaving the vehicle.

Luggage compartment lid

Openingtheluggagecompartmentlidwith the remote control

Press button C on the remote controltwice within three seconds.

Closing the luggage compartmentlid

E78263

A recessed grip is incorporated inside theluggage compartment lid to facilitateclosing.

Automatic relocking

The doors will relock automatically if youdo not open a door within 45 seconds ofunlocking the doors with the remotecontrol. The door locks and the alarm willreturn to their previous state.

33

Locks

Reprogramming theunlockingfunction

The unlocking function may bereprogrammed so that all the doors areunlocked or only the driver’s door and theluggage compartment lid are unlocked.See Programming the remotecontrol (page 28).

KEYLESSENTRY

General information

WARNING

The keyless entry system may notfunction if the key is close to metalobjects or electronic devices such

as mobile phones.

Note: If the door handles are pulledrepeatedly during a short period of timewithout the presence of a valid passivekey, the system will become inoperablefor 30 seconds.

The passive entry systemwill not functionif:• The passive key frequencies are

jammed.• The passive key battery is flat.

Note: If the passive entry system doesnot function, you will need to use the keyblade to lock and unlock your vehicle.

The keyless system allows the driver tooperate the vehicle without the use of akey or remote control.

E78276

Passive locking and unlocking requires avalid passive key to be locatedwithin oneof the three external detection ranges.These are located approximately one anda half metres from the driver and frontpassenger door handles and the luggagecompartment lid.

Passive key

The vehicle can be locked and unlockedwith the passive key. The passive key canalso be used as a remote control. SeeLocking and unlocking (page 32).

Locking the vehicle

WARNING

The vehicle does not lock itselfautomatically. If no locking button ispressed, the vehicle will remain

unlocked.

E87384

34

Locks

E87435

Locking buttons are located on each ofthe front doors and the luggagecompartment lid.

To activate central locking and arm thealarm:• Press a locking button once.

To activate double locking, to arm thealarm and the interior sensors:• Press a locking button twice within

three seconds.

Note: Once activated, the vehicle willremain locked for approximately threeseconds. This is to allow you to pull a doorhandle and check if the vehicle is locked.When the delay period is over, the doorscan be opened again, provided thepassive key is within the respectivedetection range.

Luggage compartment lid

Note: The luggage compartment lidcannot be closed and will pop back up ifthe passive key is located inside theluggage compartment.

Note: If a second valid passive key islocated within the luggage compartmentlid detection range, the luggagecompartment lid can be closed.


Note: If the vehicle remains locked forlonger than three days, the system willenter an energy-saving mode. This is toreduce the discharge of the vehiclebattery. When the vehicle is unlockedwhile in this mode, the reaction time ofthe system may be a little longer thannormal. Unlocking the vehicle once willdeactivate the energy-saving mode.

E78278

Pull one of the door handles or theluggage compartment lid handle.

Note: A valid passive key must belocatedwithin the detection range of thatdoor.

One long flash of the direction indicatorsconfirms that all the doors, the luggagecompartment lid and the fuel filler flaphave been unlocked and that the alarmhas been disarmed.

Unlocking only the driver's door

If the unlocking function is reprogrammedso that only the driver’s door is unlocked( See Programming the remotecontrol (page 28). ), note the following:

35

Locks

If the driver’s door is the first door whichis opened, the other doors will remainlocked. All the other doors can beunlocked from inside the vehicle by usingthe unlock button next to the driver’s doorhandle. Doors canbeunlocked individuallyby pulling the interior door handles onthose doors.

If the front passenger door or one of therear doors is the first door which isopened, all the doors and the luggagecompartment lid will be unlocked.

Disabled keys

Any keys left inside the vehicle interiorwhen it is locked will be disabled.

A disabled key cannot be used to turn theignition on or start the engine.

In order to use these passive keys again,they have to be enabled.

To enable all your passive keys, unlockthe vehicle using a passive key or theremote control unlocking function.

All passive keys will then be enabled if theignition is turned on or the vehicle isstarted using a valid key.

Locking and unlocking thedoorswith the key blade

1

2

E78284

1. Slide the release slider in the directionof the arrow and pull out the key bladewith your thumb.

2. Remove the key blade and insert itinto the lock.

GLOBALOPENINGANDCLOSING

You can also operate the electricwindowswith the ignition off via the globalopening and global closing function.

Note: Global closing will only operate ifyou have set the memory correctly foreach window. See Electricwindows(page 60).

Global opening

E71955

To open all the windows, press and holdthe unlock button for at least threeseconds. Press either the lock or theunlockbutton again to stop the openingfunction.

36

Locks

Global closing

Vehicleswithout keyless entry

WARNING

Take care when using globalclosing. In an emergency, press abutton immediately to stop.

E71956

To close all the windows, press and holdthe lock button for at least threeseconds. Press any button again to stopthe closing function. The anti-trap functionis also active during global closing.

Vehicleswith keyless entry

E87384

WARNING

Take care when using globalclosing. In an emergency, press thebutton on the driver’s door handle

to stop.

Note: Global closing can be activatedusing the button on the driver’s doorhandle. Global opening and closing canalso be activated using the buttons on thepassive key.

To close all the windows, press and holdthe button on the driver’s door handle forat least two seconds. The anti-trapfunction is also active during globalclosing.

37

Locks


The engine immobiliser is a theftprotection system that prevents someonefrom starting the engine with anincorrectly coded key.

CODEDKEYS

Note:Do not shield your keys withmetalobjects. This may prevent the receiverfrom recognising your key as a valid one.

Note: Have all of your remaining keyserased and recoded if you lose a key. Askyour dealer for further information. Havereplacement keys recoded togetherwithyour existing keys.

If you lose a key, you can obtain areplacement from your Ford Dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtainadditional keys from your Ford Dealer.

ARMINGTHEENGINEIMMOBILISER

The engine immobiliser is armedautomatically a short time after you haveswitched the ignition off.

The indicator in the instrument cluster willflash to confirm that the system isoperating.

DISARMINGTHEENGINEIMMOBILISER

The engine immobiliser is disarmedautomaticallywhen you switch the ignitionon with a correctly coded key.

The indicator in the instrument cluster willcomeon for approximately three secondsand then go out. If the indicator stays onfor one minute or flashes forapproximately one minute and thenrepeatedly at irregular intervals, your keyhas not been recognised. Remove thekey and try again.

If you are unable to start the engine witha correctly coded key, this indicates amalfunction. Have the immobiliserchecked immediately.

38

Engine immobiliser


Perimeter alarm

The system acts as deterrent againstunauthorised access to your vehiclethrough the doors and the bonnet. It alsoprotects the audio unit.

Interior sensors

WARNINGSThis system functions correctly onlyif all windows and the sunroof arecompletely closed.

The systemshould not be activatedif any persons, animals or othermoving objects are inside the

vehicle.

The sensors in the interior lamp unitmust not be covered up.

E71401

The system acts as deterrent againstunauthorised intrusion by sensing anymovement within the vehicle.

The interior sensing alarm is armedtogether with the central locking system.

To deactivate the interiorsensors

E80555

Press the upper part of the switch nextto the driver’s door handle.

Triggering the alarm

Once armed, the alarm is triggered in anyof the following ways:

• If someone opens a door, the luggagecompartment or the bonnet withouta valid key or remote control.

• If someone removes the audio ornavigation system.

• If the ignition is turned to position I, IIor III without a valid key.

• If the interior sensors detectmovement within the vehicle.

If the alarm is triggered, the alarm hornwillsound for 30 seconds and the hazardwarning flashers will flash for fiveminutes.

Any further attempts to perform one ofthe above will trigger the alarm again.

ARMINGTHEALARM

To arm the alarm, lock the vehicle. SeeLocks (page 32).

39

Alarm

DISARMINGTHEALARM

Vehicleswithout keyless entry

Perimeter alarm

Disarmand silence the alarmby unlockingthe doors with the key and switching theignition on with a correctly coded key, orunlocking the doors or the luggagecompartment lid with the remote control.

Category one alarm

Disarmand silence the alarmby unlockingthe doors with the key and switching theignition on with a correctly coded keywithin 12 seconds, or unlocking the doorsor the luggage compartment lid with theremote control.


Note: A valid passive key must belocatedwithin the detection range of thatdoor for keyless entry. See Keylessentry (page 34).

Perimeter alarm

Disarmand silence the alarmby unlockingthe doors and switching the ignition on,or unlocking the doors or the luggagecompartment lid with the remote control.

Category one alarm

Disarmand silence the alarmby unlockingthe doors and switching the ignition onwithin 12 seconds, or unlocking the doorsor the luggage compartment lid with theremote control.

40

Alarm

ADJUSTINGTHESTEERINGWHEEL

WARNING

Never adjust the steering wheelwhen the vehicle is moving.

Note:Make sure that you are sitting inthe correct position. See Sitting in thecorrect position (page 93).

1

2

2

E95178

3E95179

WARNING

Make sure that you fully engage thelocking lever when returning it to itsoriginal position.

AUDIOCONTROL

Select radio, CD or cassettemode on theaudio unit.

The following functions can be operatedwith the remote control:

Volume

E78046

Volume up: Press the top button on theback of the remote control.

Volume down: Press the bottom buttonon the back of the remote control.

41

Steeringwheel

Seek

E78047

Move the lever up or down:

• In radiomode, this will locate thenext radio station up or down thefrequency band.

• In CDmode, it will select the next orprevious track.

Mode

E78048

Briefly press the button on the side:

• In radiomode, this will locate thenext pre-set radio station.

• In CDmode, this will select the nextCD if a CD changer is fitted.

• In all modes to abort a trafficmessage during broadcasting.

Press and hold the button on the side:

• In radiomode to change thewaveband.

VOICECONTROL

E78049

To select or deselect voice control, pressthe button on the top.

For further information See Voicecontrol (page 194).

42

Steeringwheel

WINDSCREENWIPERS

E71012

A

B

C

D

Single wipeA

Intermittent wipe or autowipersB

Normal wipeC

High speed wipeD

Intermittentwipe

E71013

C

A B

Long wipe intervalA

Intermittent wipeB

Short wipe intervalC

Automaticwiper system

Some models without autowipers arefitted with a speed-dependent frontscreen wiper system.

When the vehicle is slowed to walkingspeed or is brought to a standstill, thewiper speed will automatically switch tothe next lower wiper speed setting.

When the vehicle speed is increased, thewiper speed will return to themanually-chosen setting.

Moving the wiper lever when the systemis operating will switch off the system.

If the vehicle is again slowed to walkingspeed or is brought to a standstill, thesystem is reactivated.

AUTOWIPERS

CAUTIONSDo not switch autowipers on in dryweather conditions. The rain sensoris very sensitive and the wipers may

operate if dirt, mist or flies hit thewindscreen.

Replace thewiper blades as soon asthey begin to leave bands of waterand smears. If you do not replace

them, the rain sensor will continue todetect water on the windscreen and thewipers will operate, even though themajority of the windscreen is dry.

Fully defrost the windscreen in icyconditions before you switchautowipers on.

Switch autowipers off before youenter a car wash.

43

Wipers andwashers

E71013

C

A B

Low sensitivityA

OnB

High sensitivityC

If you switch autowipers on, the wiperswill not cycle until water is detected onthe windscreen. The rain sensor will thencontinuously measure the amount ofwater on the windscreen and adjust thespeed of the wipers automatically.

Adjust the sensitivity of the rain sensorusing the rotary control. With lowsensitivity, the wipers will operate whenthe sensor detects a lot of water on thewindscreen. With high sensitivity, thewipers will operate if the sensor detectsa small amount of water on thewindscreen.

WINDSCREENWASHERS

E71016

WARNING

Donot operate thewasher formorethan 10 seconds at a time, andnever when the reservoir is empty.

While the button at the end of the lever ispressed the washer will work inconjunction with the wipers.

After releasing the button, the wipersoperate for a short time.

REARWINDOWWIPERANDWASHERS

Intermittentwipe

E71017

Pull the lever towards the steering wheel.

Reverse gearwipe

The rear wiper will be activatedautomaticallywhen selecting reversegearif:• the rear wiper is not already switched

on,• the wiper lever is in position A, B, C

or D and• the front wiper is operating (when set

to position B).

The rear wiper will follow the front wiperinterval (at intermittent or normal speed).

44

Wipers andwashers

Rearwindowwasher

E71018

WARNING

Donot operate thewasher formorethan 10 seconds at a time, andnever when the reservoir is empty.

While the lever is pulled towards thesteering wheel the washer will work inconjunction with the wipers.

Once the wash and wipe cycle iscompleted, thewiperswill pause and thenperform one more wipe to clear thewindscreen.

After releasing the lever, the wipersoperate for a short time.

ADJUSTINGTHEWINDSCREENWASHERJETS

E73425

The eye ball jets can be adjusted preciselyusing a pin.

HEADLAMPWASHERS

The headlamp washers will operate withthe windscreen washers when theheadlamps are on.

Note: To stop the washer fluid reservoiremptying quickly, the headlamp washerswill not operate every time that you usethe windscreen washers.

45

Wipers andwashers

CHECKINGTHEWIPERBLADES

E66644

Run the tip of your fingers over the edgeof the blade to check for roughness.

Clean the wiper blade lips with waterapplied with a soft sponge.

CHANGINGTHEWIPERBLADES

Windscreenwiper blades

E78156

Lift thewiper arm. Position thewiper bladeat a right angle to thewiper arm. Removethe blade from the arm and replace it.

Rearwindowwiper blades

Lift the wiper arm and position the wiperblade at a right angle to the wiper arm. Toremove, press the retaining clip,disengage the wiper blade and pull it offthe arm in the opposite direction.

46

Wipers andwashers

LIGHTINGCONTROL

Lighting control positions

E71094 D

B CAF

E

OffA

Side and tail lampsB

HeadlampsC

Front fog lampsD

Rear fog lampsE

Parking lampsF

Parking lamps

CAUTION

Prolonged use of the parking lampswill discharge the battery.

Switch off the ignition.

Push the lighting control inwards and turnit to position F.

Main and dipped beam

E71095

Pull the lever fully towards the steeringwheel to switch between main anddipped beam.

Headlamp flasher

Pull the lever slightly towards the steeringwheel.

Homesafe lighting

Switch the ignition off and pull thedirection indicator lever towards thesteering wheel to switch the headlampson. You will hear a short tone. Theheadlamps will go off automatically after3 minutes with any door open, or 30seconds after the last door has beenclosed.

With all doors closed, but within the 30second delay, opening any doorwill resultin the 3 minute timer starting again.

The home safe lights can be cancelled byeither pulling the direction indicator levertowards the steering wheel again or byturning the ignition switch ON.

47

Lighting

AUTOLAMPS

E73840

Note: If you have switched autolampson, you can only switch the main beamon when autolamps has switched theheadlamps on.

The headlamps will come on and go offautomatically depending on the ambientlight.

FRONT FOGLAMPS

E71096

WARNING

Only use the front fog lamps whenvisibility is considerably restricted byfog, snow or rain.

Note: You cannot switch the front foglamps on if you have switched autolampson.

REARFOGLAMPS

E71097

WARNING

Donot use the rear fog lampswhenit is raining or snowing and visibilityis more than 50 metres.

Note: You cannot switch the rear foglamps on if you have switched autolampson.

HEADLAMPLEVELLING

Note: Vehicles with Xenon headlampsare equipped with automatic headlamplevelling.

48

Lighting

E74611

A

B

Raise beamsA

Lower beamsB

Set the headlamp levelling control to zerowhen your vehicle is unloaded.

You can adjust the level of the headlampbeams according to the vehicle load.

ADAPTIVE FRONT LIGHTINGSYSTEM (AFS)

E72897

A

B

A

B

without AFSA

with AFSB

49

Lighting

The AFS adjusts the headlamp dippedbeamdepending on vehicle direction andspeed. It improves visibility when you aredriving at night and helps to reduceheadlamp glare for oncoming drivers.

The headlamps will also move when thevehicle is stationary and the steeringwheel is turned. To prevent headlampglare for the oncoming traffic, theywill onlymove towards the passenger side of thevehicle.

The system will not operate when youhave switched on the daytime runninglampsorwhen you have selected reversegear.

To activate the AFS when the daytimerunning lamps are activated, turn thelighting control to position C. SeeLighting control (page 47).

A message will appear in the informationdisplay and the headlamp indicator flashesif the system malfunctions. SeeInformationmessages (page 76).The headlampswill move to a fixed centralor dipped position. Have the systemchecked as soon as possible.

HAZARDWARNINGFLASHERS

Note:Depending on applicable laws andregulations in the country for which yourvehicle was originally built, the hazardwarning flashers may flash if you brakeheavily.

E71943

For item location: SeeQuickstart (page8).

DIRECTION INDICATORS

E71098

Note: Tap the lever up or down to makethe direction indicators flash only threetimes.

INTERIOR LAMPS

Courtesy lamp

CBA

E71945

OffA

Door contactB

OnC

50

Lighting

If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door or the luggagecompartment lid. If you leave a door openwith the ignition switch off, the courtesylamp will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch it back on, switchon the ignition for a short time.

The courtesy lampwill also comeonwhenyou switch off the ignition. It will go offautomatically after a short time or whenyou start or restart the engine.

If you set the switch to positionCwith theignition switch off, the courtesy lamp willcome on. It will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch it back on,switch on the ignition for a short time.

Reading lamps

E71946

If you switch off the ignition, the readinglamps will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch them back on,switch on the ignition for a short time.

Vanitymirror lamps

A

B

E72900

OffA

OnB

If you switch off the ignition, the vanitymirror lampswill go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch them backon, switch on the ignition for a short time.

REMOVINGAHEADLAMP

WARNING

Have Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.

1. Open thebonnet. SeeOpeningandclosing the bonnet (page 152).

51

Lighting

E78106

2

2. Remove the screw.

E78107

33

4

3. Release the retaining clips.

4. Disconnect the electrical connector.

5. Remove the headlamp.

Note:When fitting the headlamp, makesure that you fully engage the headlampin the retaining clips.

CHANGINGABULB

WARNINGSSwitch the lights and the ignition off.

Let the bulb cool down beforeremoving it.

Have Xenon bulbs changed by atrained technician. There is a risk ofelectric shock.

CAUTIONSDo not touch the glass of the bulb.

Only fit bulbs of the correctspecification. See Bulbspecification chart (page 58).

Note: The following instructions describehow to remove the bulbs. Fitreplacements in the reverse order unlessotherwise stated.

Front direction indicators

1. Remove the headlamp. SeeRemoving a headlamp (page 51).

E781082 3

2. Turn the bulb holder anti-clockwiseand remove it.

52

Lighting

3. Gently press the bulb into the bulbholder, turn it anti-clockwise andremove it.

Headlampmain beam


E115158

2. Remove the cover.

E1151603

5

4


4. Release the retaining clip.

5. Remove the bulb.

Headlampdipped beam


2

E115162


E917343 4

3. Turn the bulb holder anti-clockwiseand pull it out.

4. Remove the bulb.

Side lamps


53

Lighting

E115158


E115161

4

3

3. Squeeze the clips on either side of thebulb holder and pull it out.

4. Remove the bulb.

Front fog lamps

1

2

E91735

1. Prise out the fog lamp bezel at itsbase, slide the bezel downwards andremove it.

2. Loosen the screws and pull out thelamp assembly.

3

4

E91736


4. Remove the bulb.

54

Lighting

Side repeaters

12

E98658

1. Tip themirror as far down as possible.Using a suitable implement release theretaining clip.


3

4

E98659

3. Using a suitable implement release theretaining clip. Remove the bulb andthe bulb holder.

4. Remove the bulb.

Approach lamps

E72264

1

55

Lighting

1. Turn themirror glass as far inwards aspossible. Using a suitable implementrelease the retaining clip.

E72265

2

3

2. Remove the lamp.

3. Remove the bulb.

Rear lamps

Note: The LEDboard is not a serviceableitem, please consult your dealer if this fails.

Central brake lamp

Note: The LEDboard is not a serviceableitem, please consult your dealer if this fails.

Number plate lamp

1

2

3

E79606

1. Remove the screws.

2. Remove the lens.

3. Remove the bulb.

Front interior lamp

Vehicleswith a perimeter alarm

E78128

1

2

1. Carefully prise out the lamp.

2. Remove the lens.

3E78129

3. Remove the bulb.

56

Lighting

Vehicleswithacategoryonealarm

E73091

1

2


2. Remove the lens.

E73092

3

3. Remove the bulb.

Front reading lamps

E73938

1

2



E739393

3. Remove the bulb.

Vanitymirror lamps

1

2

E78131


2. Remove the bulb.

57

Lighting

Luggage compartment lamp

13

2

E79605



3. Remove the bulb.

BULBSPECIFICATIONCHART

Power (watt)SpecificationLamp

21PY21WFront direction indicator

55H1Headlamp main beam

551H7Headlamp dipped beam

351D1SHeadlamp dipped beam

55H11Front fog lamp

5W5WSide lamp

5WY5WSide repeater

5W5WApproach lamp

21PY21WRear direction indicator

21/5P21/5WBrake lamp

21P21WRear fog lamp

21P21WReversing lamp

5W5WNumber plate lamp

6W6W XenonInterior lamp

58

Lighting

Power (watt)SpecificationLamp

5W5W2J6Reading lamp

5W5Wn5YVanity mirror lamp

5W5WLuggage compartment lamp

1Fit a replacement with the same rating as the one you have removed.

59

Lighting

ELECTRICWINDOWS

WARNING

Donot operate the electricwindowsunless they are free fromobstruction.

Note: If you operate the switches oftenduring a short period of time, the systemmight become inoperable for a certaintime to prevent damage due tooverheating.

Switch on the ignition to operate theelectric windows.

Global opening and closing

You can also operate the electricwindowswith the ignition off via the globalopening and closing function. SeeLocks(page 32).

Driver's door switches

You can operate all the windows with theswitches on the door trim panel of thedriver’s door.

E70848

Opening and closing thewindows automatically

Press or lift the switch to the secondaction point and release it completely.Press or lift it again to stop the windows.

Safetyswitchforrearwindows

Note: You can always operate the rearwindows from the driver’s door.

E70850

A switch in the driver’s door disables therear electric window switches.

The light in the switch comes on and thelights in the rear window switches go offwhen the rear windows are disabled.

Anti-trap function

WARNING

Careless closingof thewindowscanoverride the protection function andcause injuries.

The electric windows will stopautomatically while closing and reversesome distance if there is an obstacle inthe way.

60

Windows andmirrors

Overriding the anti-trap function

CAUTION

While you close the window for thethird time, the anti-trap function isdisabled. Make sure there are no

obstacles in the way of the closingwindow.

To override this protection function whenthere is a resistance, e.g. in the winter,proceed as follows:

1. Close the window twice until itreaches the resistance and let itreverse.

2. Close the window a third time to theresistance. The anti-trap function isdisabled and you cannot close thewindowautomatically. Thewindowwilloverride the resistance and you canclose it fully.

3. If the window does not close after thethird attempt, have it checked by anexpert.

Resetting thememory of theelectricwindows

WARNING

The anti-trap function is deactivateduntil you have reset the memory.

After the battery has been disconnectedfrom the vehicle you must reset thememory separately for each window:

1. Lift and hold the switch until thewindow is fully closed.

2. Release the switch.

3. Lift the switch again for one moresecond.

4. Push and hold the switch until thewindow is fully open.

5. Release the switch.

6. Lift and hold the switch until thewindow is fully closed.

7. Open the window and try to close itautomatically.

8. Reset and repeat procedure if thewindow does not close automatically.

EXTERIORMIRRORS

WARNING

Do not overestimate the distanceof the objects that you see in theconvex mirror. Objects seen in

convex mirrors will appear smaller andfurther away than they actually are.

Manual foldingmirrors

Folding

Push themirror towards the doorwindowglass.

Unfolding

Make sure that you fully engage themirrorin its support when returning it to itsoriginal position.

ELECTRIC EXTERIORMIRRORS

Note:When the mirrors are operatedoften during a short period of time, thesystem might become inoperable for acertain time to prevent damage due tooverheating.

The electric exteriormirrors are fittedwitha heating element that will defrost ordemist the mirror glass. See Heatedwindows andmirrors (page 87).

61

Windows andmirrors

A CB

E122704

Left-hand mirrorA

OffB

Right-hand mirrorC

Mirror tilting positions

E122705

Electric foldingmirrors

Note: The switch must be in position B.

E122706

The electric folding mirrors operate withthe ignition on.

Press the button to fold or unfold themirrors.

If you press the switch again while themirrors are moving, they will stop andreverse the direction of movement.

AUTO-DIMMINGMIRROR

E71028

The auto-dimming mirror will adjustautomaticallywhen hit by glaring light frombehind. It will not work when you haveselected reverse gear.

62

Windows andmirrors

GAUGES

Type 1

E98733

A B C

E

D

TachometerA

Engine coolant temperature gaugeB

Fuel gaugeC

SpeedometerD

Information displayE

63

Instruments

Type2 and3

E98738

A B C

E

D

TachometerA

Engine coolant temperature gaugeB

Fuel gaugeC

SpeedometerD

Information displayE

Engine coolant temperaturegauge

All vehicles

Shows the temperature of the enginecoolant. At normal operating temperature,the needle will remain in the centresection.

CAUTION

Do not restart the engine until thecause of overheating has beenresolved.

64

Instruments

If the needle enters the red section, theengine is overheating. Stop the engine,switch the ignition off and determine thecause once the engine has cooleddown. See Engine coolant check(page 163).

Fuel gauge

The arrow adjacent to the fuel pumpsymbol indicates on which side of thevehicle the fuel filler cap is located.

WARNINGLAMPSANDINDICATORS

The following warning lamps andindicators illuminate when the ignition isswitched on:

• Airbag

• Oil pressure

• ABS

• Stability control (ESP)

• Engine

• Doors open

• Brake system

• Frost

• Power steering

• Ignition

If a warning or indicator lamp does notilluminate when the ignition is switchedon, it indicates a malfunction. Have thesystem checked by properly trainedtechnician.

ABSwarning lamp

If it illuminates when you aredriving, this indicates amalfunction. You will continue

to have normal braking (without ABS).Have the system checked by a properlytrained technician as soon as possible.

Airbagwarning lamp

If it illuminates when you aredriving, this indicates amalfunction. Have the system

checked by a properly trained technician.

Brake system lamp

It illuminates when the parkingbrake is engaged.

WARNING

Reduce your speed gradually andstop your vehicle as soon as it issafe to do so. Use your brakes with

care.

If it illuminateswhen you are driving, checkthat the parking brake is not engaged. Ifthe parking brake is not engaged, thisindicates amalfunction. Have the systemchecked by a properly trained technicianimmediately.

Cruise control indicator

E71340

It will illuminate when you haveset a speed using the cruisecontrol system. See Using

cruise control (page 132).

Direction indicators

Flashes during operation. Asudden increase in the rate offlashing warns of a failed

indicator bulb. See Changing a bulb(page 52).

Doors openwarning lamp

Illuminates when the ignition isswitched on and remains on ifany door, the bonnet or the

luggage compartment is not closedproperly.

65

Instruments

Enginewarning lamp

If it illuminates with the enginerunning, this indicates amalfunction. If it flashes when

you are driving, reduce the speed ofyour vehicle immediately. If itcontinues to flash, avoid heavyacceleration or deceleration. Have thesystem checked by a properly trainedtechnician immediately.

CAUTION

If the enginewarning lamp illuminatesin conjunction with a message, havethe system checked as soon as

possible.

Front fog lamp indicator

It will illuminatewhen you switchthe front fog lamps on.

Frostwarning lamp

WARNING

Even if the temperature rises toabove +4ºC there is no guaranteethat the road is free of hazards

caused by inclement weather.

It will illuminate and glow orangewhen the outside airtemperature is between 4ºC

(39ºF) and 1ºC (34ºF). It will glow redwhenthe temperature is below 1ºC (34ºF).

Glowplug indicator

SeeStartingadieselengine(page 114).

Headlamp indicator

It will illuminatewhen you switchthe headlamp dipped beam orthe side and tail lamps on.

Ignitionwarning lamp

If it illuminates when you aredriving, this indicates amalfunction. Switch off all

unnecessary electrical equipment. Havethe systemchecked by a properly trainedtechnician immediately.

Low fuel level warning lamp

If it illuminates, refuel as soon aspossible.

Main beam indicator

It will illuminatewhen you switchthe headlamp main beam on. Itwill flash when you use the

headlamp flasher.

Message indicator

It will illuminate when a newmessage is stored in theinformation display. See

Informationmessages (page 76).

Oil pressurewarning lamp

CAUTION

Do not resume your journey if itilluminates despite the level beingcorrect. Have the system checked

by a properly trained technicianimmediately.

66

Instruments

If it stays on after starting orilluminates when driving, thisindicates a malfunction. Stop

your vehicle as soon as it is safe to do soand switch the engine off. Check theengine oil level. See Engine oil check(page 162).

Power steeringwarning lamp

It illuminates to indicate amalfunction of the powersteering system. Full steering

will be maintained but you will need toexert greater force on the steeringwheel.Have the system checked by a properlytrained technician as soon as possible.

Rear fog lamp indicator

It will illuminatewhen you switchthe rear fog lamps on.

Seat belt reminder

See Seat belt reminder(page 26).

Shift indicator

It will illuminate to inform youthat shifting to a higher gearmay give better fuel economy

and lower CO2 emissions. It will notilluminate during periods of highacceleration, braking or when the clutchpedal is pressed.

Stabilitycontrol (ESP) indicator

While driving, it flashes duringactivation of the system. Afterswitching on the ignition, if it

does not illuminate or illuminatescontinuously while driving, this indicatesa malfunction. During a malfunction, thesystem switches off. Have the systemchecked by a properly trained technicianas soon as possible.

If you switch ESP off, the warning lampwill illuminate. The lamp will go out whenyou switch the system back on or whenyou switch the ignition off.

AUDIBLEWARNINGSANDINDICATORS

Automatic transmission

If position P is not selected, a warningchime will sound when the driver’s dooris opened.

Frost

WARNING

Even if the temperature rises toabove +4ºC there is no guaranteethat the road is free of hazards

caused by inclement weather.

Awarning chimewill sound in the followingconditions:• +4ºC or lower: frost warning

• 0ºC or lower: danger of icy roads.

Key outside car


If the engine is running and a passive keyis no longer detected within the vehicleinterior, a chimewill sound as soon as thedoor is closed.

67

Instruments

Key-in-ignition

Except vehicleswithkeylessentry

A warning tone will sound when thedriver’s door is opened if:• the key is in the ignition.


A warning tone will sound when thedriver’s door is opened if:• the ignition is still on

• the spare key is in the ignition.

Lights on

A warning chime will sound if the driver’sdoor is opened with the exterior lightsswitched on and the ignition switched off.

Low fuel

A warning chime will sound at thefollowing ranges: 80 km (50miles), 40 km(25 miles), 20 km (12 miles), 0 km (0miles).

Seat belt reminder

See Seat belt reminder (page 26).

68

Instruments

GENERAL INFORMATION

WARNING

Do not operate the informationdisplay controls when the vehicle ismoving.

Note: The information display will remainon for several minutes after you switch offthe ignition.

Various systems on your vehicle can becontrolled using the multi-function leveron the steering column. Correspondinginformation is displayed in the informationdisplay.

For detailed instructions on navigation,refer to the appropriate manual.

Controls

E73265

Use the rotary control:

• to scroll through the trip computerdisplays

• to scroll through and highlight theoptions within a menu.

Note: To scroll automatically, hold therotary control in the upward or downwardposition.

E73266

Press the SET/RESET button to:

• enter the main menu from the tripcomputer displays

• enter a sub-menu

• exit a menu

• choose and confirm a setting.

Note: If the chimes are activated, a shorttone will sound each time the button ispressed.

Type2 and3

69

Information displays

Menu structure

Trip OdoAvg FuelAvg SpeedAll

Set Clock24 Hour Mode

A B C

E98875

StandardSportComfort

Always offHelp Screen

DisplayConfigure

NAV InfoOn GuidanceAlways on

Reset Trip

Messages

Steering

ESP

Clock

Setup

70


B C

E98876

EnglishLanguage

Measure Unit

DeutschItalianoFrançaisEspañolTürkçePyccкийNederlandsPolskiSvenskaPortuguêsMetricImperial

Chimes

Aux. Heater

Low FuelGeneral WarnGeneral Info

71


A

E98884

Time 1 on

Set onceActive now

Set Time 1MondayTuesdayWednesdayThursdayFridaySaturdaySunday

Time 2 onSet Time 1MondayTuesdayWednesdayThursdayFridaySaturdaySunday

Park Heater

TRIPCOMPUTER

Type2 and3

Odometer

Registers the total mileage of the vehicle.

Tripmeter

Registers the mileage of individualjourneys.

Distance to empty

Indicates the approximate distance thevehicle will travel on the fuel remaining inthe tank. Changes in driving pattern maycause the value to vary.

Instantaneous fuel consumption

Indicates the current average fuelconsumption.

Average fuel consumption

Indicates the average fuel consumptionsince the function was last reset.

Average speed

Indicates the average speed calculatedsince the function was last reset.

Outside air temperature

Shows the outside air temperature.

Hold 'SET' to set Tyre Pres.

Recalibrates the system to the actualpressure of the tyres.

Menu

Enters the main menu. SeeGeneralinformation (page 69).

72


E74428

6.3Average Fuel

10:20

234.2 km

123456 km

l100km

A

B

C

Trip computerA

OdometerB

TripmeterC

The trip computer includes the followinginformation displays:

Trip

Dist to empty

Instant Fuel

Average Fuel

Average Speed

Outside Air

Hold ‘SET’ to set Tyre Pres

Menu

E105166

Turn the rotary control to scroll throughthe trip computer displays.

Note: The position of the trip computerdisplay may vary depending on theinformation shown in the display.

Resetting the trip computer usingthemainmenu

To reset a particular display:

1. Turn the rotary control and highlightMenu.

2. Press the SET/RESET button.3. Highlight "Reset Trip".

4. Press the SET/RESET button.5. Highlight the function to be reset.

6. Press and hold the SET/RESETbutton.

73


PERSONALISEDSETTINGS

1. Use the rotary to enter the mainmenu.

2. Press the SET/RESET button tochoose a sub-menu and adjust thesettings.

ESP

Select this option to activate or deactivateESP.

1. Use the rotary control to enter themain menu.

2. Highlight ESP and press theSET/RESET.

3. HighlightBack and repeatedly pressthe SET/RESET button to return tothe main menu.

Steering

Note: For road safety reasons, changesin theSteeringmenu can only bemadewhile the vehicle is stationary. If this menuor one of its sub-menus is openwhen thevehicle begins to move, the informationdisplay will automatically exit theSteeringmenu.

Note:When the vehicle is stationary, thesteering assistance is optimized in all threesettings and does not differ noticeably.

Standard: The standard setting issuitable for all driving styles.

Sport: The steering assistance isreduced. This suits a sportier driving styleby increasing the feedback through thesteering wheel. The sport setting is alsoan advantage when driving on icy andsnowy road conditions.

Comfort: The steering assistance isincreased. The steeringwill feel lighter andyou will not need to exert as much forceon the wheel.


2. Highlight Steering and press theSET/RESET button.

3. Highlight the desired setting and pressthe SET/RESET button to confirmthe setting.


Clock setting


2. Highlight Clock and press theSET/RESET button.

3. Highlight Set Clock and press theSET/RESET button. The hours startto flash.

4. Use the rotary control to adjust thehours to the desired setting.

5. Press the SET/RESET button toconfirm the setting. The minutes startto flash.

6. Proceed in the same way to set theminutes and the date.

7. Press the SET/RESET button toconfirm the setting.


Help screen and navigationinformation

The help screen appears for a fewsecondswhen you switch the ignition on.

If the navigation is operating, informationrelating to this system is displayed in theinformation display.

To select which information is displayedin the information display:

74



2. Highlight Setup and press theSET/RESET button.

3. Highlight Display and press theSET/RESET button.

4. Highlight Configure and press theSET/RESET button.



Navigation information

You can also choosewhen the navigationinformation is displayed in the informationdisplay. Three options are available:

• Always off: No navigationinformation is displayed in theinformation display.

• Onguidance: The navigationinformation will only appear when thenavigation system provides aguidance instruction. This function isonly available on certain navigationsystems.

• Always on: Navigation informationwill always appear in the informationdisplay when the navigation system isoperating.

To setwhennavigation information shouldbe displayed:




4. Highlight Configure and press theSET/RESET button.

5. Highlight Nav Info and press theSET/RESET button.



Language setting

A choice of eleven languages areavailable.

English, German, Italian, French, Spanish,Turkish, Russian, Dutch, Polish, Swedishand Portuguese.




4. Highlight Language and press theSET/RESET button.



Units ofmeasure

To select metric or imperial units:

Toggling the units of measure using thisdisplay will affect the following displays:• Distance to empty.

• Average fuel consumption.

• Instantaneous fuel consumption.

• Average speed.

• Outside air temperature.

• The temperature display in theautomatic climate control.

75


Note: The units of measure for outsideair temperature and the automatic climatecontrol can be toggled independent ofthe other displays. When showing theoutside air temperature, press and holdthe SET/RESET button for a short time.1. Use the rotary control to enter the

main menu.



4. HighlightMeasureUnit and pressthe SET/RESET button.



Chimedeactivation

The following chimes can be deactivated:• Low fuel warning.

• General warning messages.

• General information messages.



3. Highlight Chimes and press theSET/RESET button.



INFORMATIONMESSAGES

E73265

E73266

Press the SET/RESET button toacknowledge and remove somemessages from the information display.Other messages will be removedautomatically after a short time.

Certain messages need to be confirmedbefore you can access the menus.

Message indicator

The message indicatorilluminates to supplement somemessages. It will be red or

amber depending on the severity of themessage and will remain on until thecause of themessage has been rectified.

Message symbols

See Owner’s handbook.

76


Have the system checked atthe next service.

Have the system checked assoon as possible.

Stop your vehicle as soon as itis safe to do so.

Viewing currentmessages

Type2 and3


2. HighlightMessages and press theSET/RESET button.

3. Use the rotary control to view thecurrent messages.

4. Press SET/RESET to acknowledgethe message and exit the menu.

Doors open

SystemWarning lampMessage

Locks.redDriver door open

Locks.redDriver side rear door open

Locks.redPassenger door open

Locks.redPassenger side rear door open

Locks.redLuggage comp. open

Locks.redBonnet open

Locks. Close all the doors to startthe car.amberDoor ajar close door

Keyless system


Keyless system.redImmobiliser malfunction

You willONLY be able restartyour vehicle up to a maximum offive times or for a period of up to56hours afterwhich the vehiclecannot be started. Have thesystem checked by a properlytrained technician as soon aspossible.

redSteering malfunction

77



Keyless system. See Keylessentry (page 34).amberKey not detected

Keyless system. See Keylessentry (page 34).amberKey outside car

Change battery. SeeChangingthe remote control battery(page 28).

amberRemote key battery low

Have your vehicle checked by aproperly trained technician.-Steering malfunction

Keyless system.-To start press brake

Keyless system.-To start press clutch

Lighting


Brake lamp switch. The vehiclecan be driven as normal.However, cruise control cannotbe switched on. Have the systemchecked by a properly trainedtechnician as soon as possible.

redBrake light fault

Adaptive front lighting system(AFS).amberAdaptive front light failure

Maintenance


Cooling system.redHigh engine temperature

The brake fluid level is low. Checkthe brake fluid level. See Brakeand clutch fluid check (page163).

redLow brake fluid level

78



Engine. Stop the vehicle as soonas safely possible and switch offthe engine immediately. Have thesystem checked by a properlytrained technician immediately.

redEngine malfunction

Electronic acceleration control(EAC). The vehicle can be drivenbut the acceleration rate will benoticeably reduced. Maximumvehicle speed will be maintained.Have the system checked by aproperly trained technician assoon as possible.

redAcceleration reduced

Appears only on vehicles fittedwith headlamp washers. Thewasher fluid level is low. Checkthe washer fluid level. SeeWasherfluidcheck (page 164).

amberLow washer fluid level

Service Indication-Service oil

Power steering


Power steering. Full steering willbe maintained but you will needto exert greater force on thesteering wheel. Have the systemchecked by a properly trainedtechnician as soon as possible.

redPower steering malfunction

Transmission


Under certain driving conditionsit is possible that the clutches inthe transmission can overheat. Inthese circumstances it is neces-sary to press the brake pedal andstop the vehicle to prevent

redTransm. overt. Press brake

79



damage to the transmission.Select N (NEUTRAL) or P(PARK) and apply the parkingbrake until the transmission hascooled and the message disap-pears from the display.

The transmission is too hot. Inthese extreme conditions thetransmission will disengage drivein order to prevent damage. Youwill not be able to drive until thetransmission has cooled.

redTrans. too hot Press brake

Automatic transmission. Haveyour vehicle checked by a prop-erly trained technician.

amberTransmission malfunction

At lowoutside temperatures, afterstarting the engine, it may takethe transmission several secondsto engage R (REVERSE) or D(DRIVE). Keep the brake pedaldepressed until these messagesdisappear from the display.

-Engagement in progressPress brake pedal

Automatic transmission.-Move shifter to P

Stability control (ESP)


Stability control (ESP). Have yourvehicle checked by a properlytrained technician.

amberESP malfunction

80



Outside air

Keep the air intakes forward of thewindscreen free from obstruction (snow,leaves etc.) to allow the climate controlsystem to function effectively.

Recirculated air

CAUTION

Prolonged use of recirculated airmaycause the windows to mist up. If thewindows mist up, follow the settings

for defrosting and demisting thewindscreen.

The air currently in the passengercompartmentwill be recirculated. Outsideair will not enter the vehicle.

Heating

Heating performance depends on thetemperature of the engine coolant.

Air conditioning

Note: The air conditioning operates onlywhen the temperature is above 4ºC(39ºF).

Note: If you use the air conditioning, thefuel consumption of your vehicle will behigher.

Air is directed through the evaporatorwhere it is cooled. Humidity is extractedfrom the air to help keep thewindows freeof mist. The resulting condensation isdirected to the outside of the vehicle andit is therefore normal if you see a smallpool of water under your vehicle.

General information oncontrolling the interior climate

Fully close all the windows.

Warming the interior

Direct the air towards your feet. In cold orhumid weather conditions, direct someof the air towards thewindscreen and thedoor windows.

Cooling the interior

Direct the air towards your face.

AIR VENTS

E77930

81

Climate control

MANUALCLIMATECONTROL

Air distribution control

A

F B

C

D

E

E71379

WindscreenA

Footwell and windscreenB

FootwellC

Face level and footwellD

Face levelE

Face level and windscreenF

You can set the air distribution control toany position between the symbols.

Blower

E75470

A

OffA

Note: If you switch the blower off, thewindscreen may mist up.

Recirculated air

Press the button to toggle betweenoutside air and recirculated air.

Heating the interior quickly

E71377

82

Climate control

Ventilation

E71378

Set the air distribution control, blower andair vents to suit your requirements.

Air conditioning

Switching the air conditioning onand off

If you turn the blower off, the airconditioning will turn off. When you turnthe blower on again, the air conditioningwill come on automatically.

Coolingwith outside air

E71380

Cooling the interior quickly

E71381

Defrosting and demisting thewindscreen

E71382

When the temperature is above 4°C(39°F), the air conditioning will switch onautomatically. Make sure that the bloweris on. The indicator in the switch willilluminate during defrosting anddemisting.

If you move the air distribution control toa position other than A, the A/C willremain on.

You can switch the air conditioning andrecirculated air on and off while the airdistribution control is set to position A.

If necessary, switch the heated windowson. See Heatedwindows andmirrors (page 87).

83

Climate control

Reducing interior air humidity

E71383

AUTOMATICCLIMATECONTROL

E91390

The system controls the temperature,amount and distribution of the air flowautomatically and adjusts themaccordingto the driving and weather conditions.Pressing theAUTObuttononce switcheson the auto mode.

The system in your vehicle is dual-zoneautomatic climate control. When thesystem is in mono mode, all thetemperature zones are linked to thedriver's zone. When you switch monomode off, the dual-zone system allowsyou to set different temperatures for thedriver's and front passenger's side.

Note: Avoid adjusting the settings whenthe vehicle interior is extremely hot orcold. The automatic climate controladjusts to the current circumstancesautomatically. For the system to functionproperly, the side and centre vents shouldbe fully open.

Note: The sunload sensor is located ontop of the instrument panel. Do not coverthe sensor with any objects.

Note:At lowoutside temperatures,whenthe system is in automode, the air streamwill be directed to thewindscreen and theside windows as long as the engine iscold.

84

Climate control

Note: For information on the automaticclimate control, on vehicles fitted with acombined Navigation and automaticclimate control system, see separatehandbook.

Setting the temperature

E91391

You can set the temperature between16ºC and 28ºC in steps of 0.5ºC. Inposition LO (below 16ºC) the system willswitch to permanent cooling, inHI (above28ºC) to permanent heating, and notregulate a stable temperature.

Monomode

In monomode, the temperature settingsfor both the driver’s and passenger’s sideare linked. If you adjust the temperatureusing the rotary control on the driver’sside, the settings will be adjusted to thesame setting on the passenger’s side. Inmono mode, MONO appears in thedisplay.

To switchmonomodeoff

Select a temperature for the passenger’sside with the rotary control on thepassenger’s side. Monomodewill switchoff andMONO disappears from thedisplay. The temperature for the driver’ssidewill remain unchanged. You can nowadjust the driver and passenger sidetemperatures independently of eachanother. The temperature settings foreach side are shown in the display. Youcan set a temperature difference of up to4ºC.

Note: If you set a temperature of greaterthan 4°C, the temperature on the othersidewill be adjusted so that the differenceremains 4°C.

Note: If you set one of the sides toHI orLO, both sides will be set to HI or LO.

To switchmonomodeback on

To switchmonomodeback on, press theMONO button.MONO reappears in thedisplay and the passenger’s sidetemperature will be adjusted to thedriver’s side temperature.

Blower

Use the buttons to adjust the blowerspeed.

The blower setting is indicated in thedisplay.

To return to automode, press theAUTObutton.

85

Climate control

Air distribution

To adjust air distribution, press the desiredbutton. Any combination of settings canbe selected simultaneously.

E70308

A B C

FootwellA

Face levelB

WindscreenC

When you select windscreen defrostingand demisting, A, B and C switch offautomatically and the air conditioningswitches on. Outside air will flow into thevehicle. You cannot select recirculatedair.

Windscreen defrosting anddemisting

E91392

Press the windscreen defrosting anddemisting button. Outside air will flow intothe vehicle. Air conditioning isautomatically selected. As long as the airdistribution is set to this position, youcannot select recirculated air.

The blower speed and the temperaturecontrol operate automatically and cannotbe adjusted manually. The blower is setto high speed and the temperature toHI.

When you select windscreen defrostinganddemisting, the heated screens switchon automatically and switch off after ashort time.

To return to automode, press theAUTObutton.

Switching the air conditioningon and off

E91393

Press the A/C button to switch the airconditioningonandoff.A/COFF appearsin the display when the air conditioning isswitched off.

A/CON appears in the display when theair conditioning is switched on.

Recirculated air

Press the recirculated air button to togglebetween outside air and recirculated air.

Note:When the system is in auto modeand the interior and exterior temperaturesare quite hot, the system selectsrecirculated air automatically tomaximisecooling of the interior. Once the selectedtemperature is reached, the system willreselect outside air automatically.

Switching off the automaticclimate control

E91394

Press theOFF button.

When switchedoff, the heating, ventilationand air conditioning system is switchedoff and recirculated air is selected.

86

Climate control

HEATEDWINDOWSANDMIRRORS

Heatedwindows

Use the heated windows to defrost ordemist the windscreen or rear window.

Note: The heatedwindowsoperate onlywhen the engine is running.

Heatedwindscreen

Note:Also defrosts the frontwasher jets.

E78039

Heated rearwindow

E78040

Heated exteriormirrors

Electric exterior mirrors are fitted with aheating element thatwill defrost or demistthe mirror glass. They will switch onautomaticallywhen you switch the heatedrear window on.

AUXILIARYHEATER

Parking heater

WARNINGSThe parking heater must not beoperated at filling stations, nearsources of combustible vapours or

dust or in enclosed spaces.

WARNINGSThe parking heater should beswitched on for approximately 10minutes at least once a month all

year round. This prevents thewater pumpand heater motor from seizing.

Note: The parking heater will onlyoperate if there is at least 7.5 litres (1.6gallons) of fuel in the fuel tank and theambient temperature is below 15°C(59°F). The heater will not operate if thebattery is low.

Note: The heating depends on theoutside air temperature.

Note:When the parking heater isactivated, exhaust fumesmay come fromunder the sides of the vehicle. This isnormal.

Note: On vehicles with manual climatecontrol the heating of the vehicle interioris dependent on the temperature, airdistribution and blower control settings.

The parking heater operatesindependently of the vehicle heater byheating the engine’s coolant circuit. It isfed from the vehicle fuel tank. You canalso use it while the vehicle is in motion tohelp the vehicle heater warm up theinterior more quickly.

Used properly, the parking heaterprovides the following benefits:

• It preheats the interior of the vehicle.

• It keeps the windows clear of ice inthe event of frost and preventscondensation.

• It avoids cold starts and allows theengine to reach operatingtemperature sooner.

To prevent the battery from discharging:

87

Climate control

• Once the parking heater hasperformedone heating cycle, the nextprogrammed heating cycle will onlybe carried out if you have started thevehicle’s engine in between.

• After a heating cycle, drive the vehiclefor at least the period of the heatingcycle.

Programming the parking heater

Note: The programmed time is the timeat which you wish the vehicle to be warmand ready to drive, not the time at whichthe heater switches on.

Note: You must programme the timesat least 70minutes in advance of the timeyou wish to set.

Note: You must set the time and datecorrectly.

To programme the heating times:

E73265

E73266


2. HighlightParkHeater and press theSET/RESET button.

E74467

One-Time

Program 1Program 2

Active now

Park Heater

• The functions Program 1 andProgram2 allow you to programmeup to two heating cycles for each dayof the week. These times will remainstored and the heaterwill warmup thevehicle at these times on these daysevery week.

• The functionOne-Time allows youto programme one heating cycle forone specific day.

• The function Active nowautomatically switches on the heater.

88

Climate control

Programming the functionsProgram 1 andProgram2

E74468

FridayThursday

TuesdayMonday

Wednesday

[07:55]

Program 1


2. Highlight Program 1 and press theSET/RESET button.

3. Highlight the day on which the heatershould warm up the vehicle.

4. Press the SET/RESET button toconfirm the selection. A cross appearsin the box next to the day to show thatthis day is selected.

5. Continue in the sameway to select allthe days on which the heater shouldwarm up the vehicle.

6. To set the time at which the vehicleshould be warmed up, highlight thetime at the top of the display andpress the SET/RESET button. Thehours start to flash.



9. Use the rotary control to adjust theminutes to the desired setting.


11. Press the SET/RESET button toexit the menu.

E74469

07:5501:12:2006

ParkheaterProgram 1

OK = change

You can use the function Program2 toset a second cycle, for example differenttimes on different days or twice on thesame day. The programming procedureis the same as for the functionProgram1.

Programming the functionOne-Time

1. HighlightOne-Time and press theSET/RESET button. The hours startto flash.



4. Use the rotary control to adjust theminutes to the desired setting.


6. Press theSET/RESET button to exitthe menu.

89

Climate control

Active now

1. Highlight Active now and press theSET/RESETbutton. A cross appearsin the box next to the function to showthat the heater is activated.

To deactivate the heater, highlightActivenow and press the SET/RESET buttonagain.

Diesel auxiliary heater(depending on country)

The diesel auxiliary heater (PTC electricalheater) aids in warming the engine andthe vehicle interior on vehicles with adiesel engine. It is switched on or offautomatically depending on the outsideair temperature, the coolant temperatureand the alternator load.

Fuel operated heater(depending on country)

The fuel operated heater aids in warmingthe engine and the vehicle interior onvehicles with a petrol or diesel engine. Itis switched on or off automaticallydepending on the outside air temperatureand the coolant temperature, unless youhave deactivated it. When the fueloperated heater is operating, a messageappears in the information display. SeeInformation displays (page 69).

To deactivate the fuel operated heater:



3. HighlightAux.Heater and press theSET/RESETbutton. A cross appearsin the box when the heater isactivated.

4. Press theSET/RESET button to exitthe menu.

ELECTRICSUNROOF

E78054

WARNING

Before operating the electricsunroof you should verify it is free ofobstructions and ensure that

children and/or pets are not in theproximity of the sunroof opening. Failureto do so could result in serious personalinjury. It is the primary responsibility of thesupervising adults to never leave a childunattended in a vehicle and to never leavethe keys in an unattended vehicle.

Note:When the switches are operatedoften during a short period of time, thesystem might become inoperable for acertain time to prevent damage due tooverheating.

Note: The electric sunroof can also beoperatedwith the ignition off via the globalopening and global closing function. SeeGlobal opening and closing (page36).

There are two ways of opening thesunroof – the rear of the sunroof lifts openor the sunroof opens from the front,sliding back under the roof. The sunroofopens and closes whilst the switch ispressed.

Switch on the ignition to operate theelectric sunroof.

90

Climate control

The power sunroof is operated by aswitch located between the sun visors.

Opening and closing thesunroof

E72188

E72185

B

A

Press to closeA

Press to openB

Tilting the sunroof

E72189

E72185

B

A

Press to openA

Press to closeB

Opening and closing thesunroof automatically

Note:When opening automatically, thesunroofwill stop about 8 cm from the fullyopened position. This position reducesthe buffeting noise which is sometimesheard when the sunroof is fully open. Thesunroof will only stop automatically in thisposition when the sunroof is openedautomatically.

91

Climate control

To open or close the sunroofautomatically press either side of theswitch to the second action point andrelease it completely. Press again to stop.

When the closed position is reached, thesunroof stops automatically.

Sunroof anti-trap protection

WARNINGSThe anti-trap function is deactivateduntil the memory has been reset.Careless closing of the window can

cause injuries.

Careless closing of the electricsunroof can override the anti-trapprotection and cause injuries.

The sunroof will stop automatically whileclosing and reverse somedistance if thereis an obstacle in the way.

To override anti-trap protection whenthere is a resistance, e. g. in the winter,proceed as follows:

WARNING

While the sunroof is being closed forthe third time, the anti-trap functionis disabled. Make sure there are no

obstacles in the way of the closingsunroof.

Close the sunroof a third time to theresistance. The anti-trap function isdisabled and the sunroof cannot beclosed automatically. The sunroof willoverride the resistance and can then beclosed fully.

If the sunroof does not close after thethird attempt, have it checked by anexpert.

Sunroof safetymode

WARNING

The anti-trap function is not activeduring this procedure. Make surethat there are no obstacles in the

way of the closing sunroof.

If the system detects a malfunction, itenters a safety mode. The sunroof willmove for only about 0.5 seconds at a timeand then stop again. Close the sunroofby pressing the button again when thesunroof stops moving. When the rear ofthe sunroof is lifted, lift the rear all the wayand then close the sunroof. Have thesystem checked by an expertimmediately.

Sunroof relearning

WARNING

The anti-trap function is not activeduring this procedure. Make surethat there are no obstacles in the

way of the closing sunroof.

In case the sunroof no longer closesproperly, follow this relearning procedure:

• Tilt the rear of the sunroof as far aspossible. Release the button.

• Press and hold the samebutton againfor 30 seconds until you see thesunroof move.

• Release the button and immediatelypress and hold it again. The sunroofwill close, open fully and then closeagain. Do not release the buttonbefore the sunroof has reached theclosed position for the second time.

If the button is not pressed continuously,the relearning functionwill be interrupted.Start the procedure once more from thebeginning.

92

Climate control

SITTING IN THECORRECTPOSITION

E68595

WARNINGSDo not adjust the seats when thevehicle is moving.

Only when you use the seat beltproperly, can it hold you in a positionthat allows the airbag to achieve its

optimum effect.

When you use them properly, the seat,head restraint, seat belt and airbags willprovide optimum protection in the eventof a collision. We recommend that you:

• sit in an upright position with the baseof your spine as far back as possible.

• do not recline the seatbackmore than30 degrees.

• adjust the head restraint so that thetop of it is level with the top of yourhead and as far forwards as possible,remaining comfortable.

• keep sufficient distance betweenyourself and the steering wheel. Werecommend a minimum of 250millimetres (10 inches) between yourbreastbone and the airbag cover.

• hold the steeringwheelwith your armsslightly bent.

• bend your legs slightly so that you canpress the pedals fully.

• position the shoulder strap of the seatbelt over the centre of your shoulderand position the lap strap tightlyacross your hips.

Make sure that your driving position iscomfortable and that you canmaintain fullcontrol of your vehicle.

MANUALSEATS

Moving the seats backwardsand forwards

E70728

WARNING

Rock the seat backwards andforwards after releasing the lever tomake sure that it is fully engaged in

its catch.

93

Seats

Adjusting the lumbar support

E70729

Adjusting the height of thedriver’s seat

E70730

Adjusting the angle of theseatback

E70731

HEADRESTRAINTS

Adjusting the head restraint

WARNINGSRaise the rear head restraint whenthe rear seat is occupied by apassenger.

When using a forward facing childrestraint on a rear seat, alwaysremove the head restraint from that

seat.

E66539

Adjust the head restraint so that the topof it is level with the top of your head.

94

Seats

Removing the head restraint Press the locking buttons and remove thehead restraint.

ELECTRICSEATS

E78060

95

Seats

REARSEATS

Comfort seat system

WARNING

Make sure that there is nothing inthe luggage compartment whichcould obstruct themovement of the

seats or get damaged when the seatsmove rearwards.

The centre seat can be folded up and theoutboard seats moved rearwards andslightly inboard to provide more leg andshoulder room for the rear passengers.

First, fold back the front of the luggagecover.

E78062

Fold up the centre seat by releasing thelever on the underside of the seat.

E78063

The complete seat will move rearwardsas the seat cushion is folded up. Fold theseat back until it engages.

E78064

Pull the lever on the outer front edge ofthe outboard seats and push the seatsrearwards. As the seats slide rearwards,they also move slightly inboard. Afterreleasing the lever, rock the seats toensure that the catch is securelyengaged.

96

Seats

To return the seats to the forwardposition, pull the lever and slide the seatsforwards. After releasing the lever, rockthe seats to ensure that the catch issecurely engaged.

To return the centre seat to its originalposition, pull the lever on the undersideof the seat. Fold the centre seat forwardsand push it back down fully until itengages.

Fold the front of the luggage coverforwards.

E78065

WARNING

Do not slide the outboard seatsrearwards into the comfort positionif the centre seat is folded forwards.

There is a risk of injury in the event of anaccident or if the centre seat falls backdown.

Foldingtheseatbacksforward

CAUTION

Do not fold the seatbacks forwardwhen the seats are in the comfortposition (slid rearwards). This could

result in damage to the seats or paneltrim. Slide the seats fully forwards.

All three seatbacks can be folded forwardindependently of one another.

E78066

Remove the seat belts from the beltguides on the outboard seatbacks. Theseat belt tongues must be inserted intothe retaining slots. The retaining slot forthe centre seat belt is located in the roof.See Fastening the seat belts (page24).

Lower the outboard head restraints andraise the centre head restraint. SeeHead restraints (page 94).

E78067

97

Seats

Pull up the lever on the side of theseatback, fold the seatback forwards andpush it down until it engages.

WARNING

To avoid scalding, never place hotdrinks in the cup holder.

A table surface and two cup holders arelocated on the rear of the centreseatback.

Returningtheseatbackstotheupright position

E78068

WARNING

Always have the rear head restraintsraised when the rear seat isoccupied by a passenger or a child

restraint. See Head restraints (page94).

Pull the lever on the seatback and lift theseatback up. The seatbackmust engagein its latch.

Make sure the seatbelts will functionproperly and are positioned in front of theseatbacks. When in use, the rear seatbelts should be placed in the belt guideson the outboard seatbacks.

Folding the seats forward

To increase the space in the luggagecompartment, the rear seats can befolded forward.

First, fold the seatback(s) forward. SeeFolding the seatbacks forward.

E78069

2

2

1

Note: All three seats can be foldedforward individually. However, if one orboth outboard seats is to be foldedforward togetherwith the centre seat, thecentre seat must be folded forward first.If only the outboard seats are to be foldedforward, the centre seatbackmust be leftin the upright position.

E78070

12

Pull the lower bar on the rear of the seatsto release them from the floor and foldthe seats forward.

98

Seats

E78071

WARNING

Always attach the bungee strap tothe front head restraint when a rearseat is folded forwards. Failure to do

so may result in the seat falling backdown.

Once the seats are folded forward, pullout and attach the bungee straps to thefront head restraints to hold the foldedseats in the upright position.

Returning the seats to theseating position

E78073

WARNINGSTo avoid injury, take care whenfolding the seats down.

Make sure that the locking hole onthe floor is clear of sand, rock or anyobjectswhichmayprevent the seat

from locking.

CAUTION

Make sure that no objects arelocated in the storage compartmentsunder the rear seats which could get

damaged when the seats are foldeddown.

Before folding the seats back down, pullthe lower bar on the rear of each seat andcheck that the latches are in thedelatched (extended) position.

99

Seats

E78074

Note: If one or both outboard seats arefolded forward together with the centreseat, the outboard seats must be foldedback down first.

WARNING

When the bungee strap isdetatched from the head restraint,it will recoil back into the seat. Take

care not to get your fingers caught whenthe strap recoils.

Detach the bungee straps.

WARNING

Make sure the seat is securelylocked by pushing forward andrearward on the top of the seatback

or by trying to pull up the edge of thecushion.

Fold the seats back down until theyengage.

Raise the seatbacks ensuring that theyengage in their latches.

WARNING

When folding the seatbacks up,make sure that the belts are visibleto an occupant and not caught

behind the seat.

The rear seatbelts should be placed in thebelt guides on the outboard seatbacks.

Removing the seats

To increase the space in the luggagecompartment, the rear seats can beremoved completely.

Fold the seats forward. SeeFolding theseats forward.

Fold up the seat to be removed to anangle of approximately 45 degrees to thefloor.

E78075

With the seat in this position, push downboth levers marked in red to rotate thelocking claws to the open position.

E78076

100

Seats

WARNING

The rear seats are heavy. To avoidinjury, take care when lifting theseats.

In order to remove the seats from theretaining bar on the floor, the seat shouldbe held at an angle of approximately 45degrees to the floor.

Lift the seats out.

Installing the seats

E78077

WARNINGSTo avoid injury, take care whenfolding the seats down.

Make sure that the locking hole onthe floor is clear of sand, rock or anyobjectswhichmayprevent the seat

from locking.

CAUTION

Make sure that no objects arelocated in the storage compartmentsunder the rear seats which could get

damaged when the seats are foldeddown.

Ensure that both locking claws are rotatedto the open position.

To reinstall the seats, lower the seat ontothe retaining bar on the floor. In order todo so, the seat should be held at an angleof approximately 45 degrees to the floor.

E78073

Before folding the seats back down, pullthe lower bar on the rear of the seat andcheck that the latches are in thedelatched (extended) position.

Push the seat back down until it engages.

HEATEDSEATS

CAUTION

Operating this function with theengine off will drain the battery.

101

Seats

The heated front seats are operated byrotary controls in the instrument panel.For item location: SeeQuickstart (page8).

The maximum temperature is reachedafter five or six minutes. It is regulatedthermostatically.

The seat heating will operate only whenthe ignition is in position II.

102

Seats

SUNBLINDS

Panoramic roof

E91500

The roof blind is in two sections. Pull thehandle from the front or rear of thepanoramic roof and fully extend therequired section.

To open the blind, slightly pull the handleagainst the spring mechanism, and pushup to release from the hooks.

Note: Each blind section will only extendto the middle of the panoramic roof.

INSTRUMENT LIGHTINGDIMMER

E70454

CIGAR LIGHTER

CAUTIONSIf you use the socket when theengine is not running, the batterymay discharge.

Do not hold the cigar lighter elementpressed in.

Note: You can use the socket to power12 volt appliances that have a maximumcurrent rating of 15 Amperes. Use onlyFord accessory connectors or connectorsspecified for use with SAE standardsockets.

E72972

Press the element in to use the cigarlighter. It will pop out automatically.

103

Convenience features

AUXILIARYPOWERSOCKETS

CAUTION

If you use the socket when theengine is not running, the batterymay discharge.

Note: You can use the socket to power12 volt appliances that have a maximumcurrent rating of 10 Amperes. Use onlyFord accessory connectors or connectorsspecified for use with SAE standardsockets.

E78056

Auxiliary power sockets are located in thecentre console and in the luggagecompartment.

Power inverter

CAUTIONSIf you use the socket when theengine is not running, the batterymay discharge.

If the LED flashes continuously,re-insert the plug or switch theignition off and then on again.

It will switch off if the temperature isabove 85°C (185°F). The LED willflash once.When it has cooled down

it will switch back on automatically.

Do not exceed themaximum poweroutput. If you do, the LED will flashtwice. Remove the plug and re-insert

it.

CAUTIONSIf the LED flashes 3 or 4 times, havethe system checked by a properlytrained technician.

Note: You can use the socket to power230 volt appliances that have amaximumrating of 150 watts.

E98199

CENTRECONSOLE

Rear seat centre console

Installing the rear seat centreconsole

WARNING

Close the lid of the console beforeinstalling it.

1. Fold up the rear centre seat. SeeRear seats (page 96).

104


E78102

2

3

2. Place the console onto the storagetray between the outboard seats.

3. Slide the guide arm at the rear of theconsole under the bar on the tray.

E78103

5

5

4

4. Push theconsole rearwardsanddownat the front until it clicks into position.

5. Slide the outboard seats rearwards.

Removing the rear seat centreconsole

WARNING

Close the lid of the console beforeremoving it.

E78104 1

2

1. Press the locking handle under thefront of the console.

2. Pull the console up at the front edgeand lift it out.

COOLBOX

E78162

105


For keeping cool pre-cooled food/drinks.Press the switch to turn on or off.Operates only when the ignition isswitched on.

STORAGECOMPARTMENTS

Front storage compartment

E92189

WARNING

Never drive with the front storagecompartment lid open. This willobscure your vision out of the

windscreen. Before setting off, alwaysensure that the lid is securely engaged.

Note: Avoid keeping heat-sensitiveobjects and liquids in the front storagecompartment.

Front centre console storagecompartment

E73704 E72905

E72905

106


Driver’s seat storage bin

E78094

A storage bin is located on the outboardside of the driver’s seat.

Rear centre console storagecompartment

E78101

The console can be used to store itemsand also serves as an armrest. It includesa small net in the lid and a moveable tray.

Storage area under the rearcentre seat

E78095

To gain access to the storage area, foldup the rear centre seat cushion. SeeRear seats (page 96).

CUPHOLDERS

WARNING

Do not place hot drinks in the cupholders when the vehicle is moving.

Seat back trays

WARNING

Do not use the trays when thevehicle is moving. Make sure thatyou secure the trays in the lowered

position before setting off.

107


E72630

GLASSESHOLDER

E75193

E91508

TOLLREADER

E78729

40

5

70

120

On vehicleswith an anti-heatwindscreen,toll readers should be placed in the areaas shown (all measurements shown inmillimetres), otherwise communicationperformance with toll stations may bereduced.

The toll reader should be placed on thepassenger side to prevent the readerfrom obscuring the driver’s vision (e.g. attraffic lights).

108


CHILDMINDERMIRROR

E75192

CDCHANGER

This is located under the front passengerseat.

AUXILIARY INPUT (AUX IN)SOCKET

See separate audio handbook.

Type 1

E91510

Type2

E91511

E92035

109


USBPORT

E91511

E115171

See Connectivity (page 213).

SATELLITENAVIGATIONUNITHOLDER

Fitting the navigation unit

1

2

E112710

Insert the navigation unit into the holderuntil you hear a distinct click.

Adjusting the holder

E112711

1

3

2

1. Unlock.

2. Adjust the holder to the desiredposition.

3. Lock.

110


Note:Make sure that the navigation unitholder is locked in position.

Removing the navigation unit

E112712 1

2

FLOORMATS

WARNING

When using the floor mats, alwaysmake sure the floor mat is properlysecured using the appropriate

fixings and positioned so that it does notinterfere with the operation of the pedals.

111


GENERAL INFORMATION

General points on starting

If the battery has been disconnected thevehicle may exhibit some unusual drivingcharacteristics for approx. 8 kilometres(5 miles) after reconnecting the battery.

This is because the engine managementsystemmust realign itself with the engine.Any unusual driving characteristics duringthis period may be disregarded.

Starting the engine by towingor pushing

WARNING

To prevent damage you must notpush or tow start your vehicle. Usebooster cables and a booster

battery. See Using booster cables(page 170).

IGNITIONSWITCH

WARNING

Never return the key to position 0or I when the vehicle is in motion.

E72128

0 The ignition is off.

I The ignition and all main electrical circuitsare disabled.

Note:Do not leave the ignition key in thisposition for too long to avoid dischargingthe battery.

II The ignition is switched on. All electricalcircuits are operational. Warning lampsand indicators illuminate. This is the keyposition when driving. You must alsoselect it when being towed.

III The starter motor is activated. Releasethe key as soon as the engine starts.

STEERINGWHEEL LOCK

WARNING

Always check that the steering isunlocked before attempting tomove your vehicle.

Vehicleswithout keylessstarting

To activate the steering wheel lock;

1. Remove the key from the ignitionswitch.

2. Turn the steering wheel.

Vehicleswith keyless starting

Your vehicle has an electronicallycontrolled steering wheel lock. Thisoperates automatically.

The steering wheel lock is activated if theignition is off, the engine not running andyour vehicle is stationary.

The steering wheel lock is deactivatedwhen the ignition is switched on.

STARTINGAPETROLENGINE

Note: You can only operate the starterfor a maximum of 30 seconds at a time.

112

Starting the engine

Cold or hot engine

All vehicles

CAUTION

When the temperature is below-20ºC (-4ºF), switch the ignition onfor at least one second before

starting the engine. This will make surethat the maximum fuel pressure isestablished for starting the engine.

Vehicleswithmanual transmission

Note: Do not touch the acceleratorpedal.

1. Fully depress the clutch pedal.

2. Start the engine.

Vehicleswith automatictransmission


1. Select park or neutral.

2. Fully depress the brake pedal.


All vehicles

If the engine does not start within 15seconds, wait for a short period and tryagain.

If the engine does not start after threeattempts, wait 10 seconds and follow theFlooded engine procedure.

If you have difficulty starting the enginewhen the temperature is below -25ºC(-13ºF), press the accelerator pedalbetween¼ to½of its travel and try again.

Flooded engine



2. Fully depress the accelerator pedaland hold it there.




2. Fully depress the accelerator pedaland hold it there.



All vehicles

If the engine does not start, repeat theCold or hot engine procedure.

Engineidlespeedafterstarting

The speed at which the engine idlesimmediately after starting will varydepending on the engine temperature.

If the engine is cold then the idle speedwill automatically be increased in order toheat the catalytic converter as quickly aspossible. This ensures that vehicleemissions are kept to an absoluteminimum.

The idle speedwill slowly decrease to thenormal level as the catalytic converterwarms up.

STARTINGAPETROLENGINE - E85

For general information on starting apetrol engine. See Starting a petrolengine (page 112).

113

Starting the engine

Starting at lowambienttemperatures

When the temperature is lower than -10°C(14°F) and the vehicle is filled with E85, anengine block heater should be used tofacilitate starting. See Engine heater(page 117). Failure to do this will result in anon start.

If the temperature is expected to remainbelow -10°C (14°F), it is recommendedthat you increase the proportion of petrolin the tank by topping up with 95 octaneunleaded petrol if the tank is not alreadyfull. About 10 litres (2.2 gallons) of petrolwill reduce the proportion of E85 in a ¾full tank from 85% to 70% and willconsiderably improve cold start capability.

If, at very low temperatures, the tank isfilled with only E85 and there is no way touse an engine block heater, you mayexperience difficulties starting the engine.

If the engine fails to start, proceed asfollows:

1. Fully depress the accelerator pedal.

2. Turn the ignition key to position III.

CAUTION

Release the ignition key as soon asthe engine has started.

3. Gradually release the acceleratorpedal after 5 seconds of enginecranking or as the engine speed rises.

If the engine fails to start, repeat steps 1,2 and 3, or connect an engine blockheater for two hours before attemptinganother start.

During starting, the fuel injectors areturnedoff as long as the accelerator pedalis depressed. This can be used to drainexcessive fuel from the intake manifoldafter several unsuccessful startingattempts.

If the battery has been disconnected orafter the fuel type has been changed, theidle speed may be irregular. This willimprove after 10 to 30 seconds.

STARTINGADIESELENGINE

Cold or hot engine

All vehicles

Note:When the temperature is below-15ºC (5ºF), you may need to crank theengine for up to 25 seconds. If youconsistently operate the vehicle in suchtemperatures, we recommend that youhave an engine block heater fitted.

Note:Continue cranking the engine untilit starts.

Note: You can only operate the starterfor a maximum of 30 seconds at a time.

Switch the ignition on and waituntil the glow plug indicatorgoes off.









114

Starting the engine

KEYLESSSTARTING

WARNINGSThe keyless starting systemmaynotfunction if the key is close to metalobjects or electronic devices such

as mobile phones.

Always check that the steeringwheel lock is deactivated beforeattempting to move your vehicle.

See Steeringwheel lock (page 112).

Note: A valid passive key must belocated inside the vehicle to switch theignition on and start the engine.

Note: To start your engine youmust alsofully depress the brake or clutch pedal,depending on the transmission fitted.

E85766

Ignition on

Press the start button once. All electricalcircuits are operational, warning lampsand indicators illuminate.

Startingwith automatictransmission

Note: Releasing the brake pedal duringengine start will stop the engine crankingand return to ignition on.

1. Make sure the transmission is in P orN.


3. Press the start button.

Startingwithmanualtransmission

Note: Releasing the clutch pedal duringengine start will stop the engine crankingand return to ignition on.


2. Press the start button.

Starting a diesel engine

Note: Engine cranking may notcommence until the engine glow plugcycle has been completed. Thismay takeseveral seconds in extremely coldconditions.

Note: Continue to press the clutch orbrake pedal until engine cranking begins.

Failure to start

The passive starting system will notfunction if:• The passive key frequencies are

jammed.• The passive key battery is flat.

If you are unable to start your vehicle carryout the following procedure.

Type 1

E87382

115

Starting the engine

1. Hold the key next to the steeringcolumn shroud exactly as shown.

2. With the key in this position you canuse the start button to switch theignition on and start your vehicle.

Type2

E87381

1. Carefully prise out the cover.

E85767

2. Insert the key into the key holder.

3. With the key in this position you canuse the start button to switch theignition on and start your vehicle.

Stopping the engine

When your vehicle is stationary, press thestart button to stop the engine. Theignition, all electrical circuits, warninglamps and indicators will be switched off.

DIESELPARTICULATEFILTER (DPF)

The DPF forms part of the emissionsreduction systems fitted to your vehicle.It filters harmful diesel particulates (soot)from the exhaust gas.

Regeneration

WARNING

Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF

regeneration process creates very highexhaust gas temperatures and theexhaust will radiate a considerableamount of heat during and after DPFregeneration, andafter youhave switchedthe engine off. This is a potential firehazard.

Unlike a normal filter which requiresperiodic replacement, the DPF has beendesigned to regenerate, or clean itself tomaintain operating efficiency. Theregeneration process takes placeautomatically. However, some drivingconditions mean that you may need tosupport the regeneration process.

If you drive only short distances or yourjourneys contain frequent stopping andstarting, occasional tripswith the followingconditions could assist the regenerationprocess:

116

Starting the engine

• Drive your vehicle, preferably on amain road or motorway, for up to 20minutes avoiding prolonged idling, butalways observing speed limits androad conditions.

• Do not switch off the ignition.

• Use a lower gear than normal tomaintain a higher engine speedduringthis journey, where appropriate.

SWITCHINGOFF THEENGINE

Vehicleswith a turbocharger

CAUTION

Do not switch the engine off when itis running at high speed. If you do,the turbocharger will continue

running after the engine oil pressure hasdropped to zero. This will lead topremature turbocharger bearing wear.

Release the accelerator pedal. Wait untilthe engine has reached idle speed andthen switch it off.

ENGINEHEATER

CAUTION

Make sure youdisconnect thepowercable from the engine heaterconnector before driving away.

Note: The engine heater connector islocated in the radiator grille at the front ofyour vehicle.

E97918

Connect the engine heater for 2 to 3hours before starting the engine.

117

Starting the engine

SAFETYPRECAUTIONS

WARNINGSStop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in

the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.

Do not use any kind of flames orheat near the fuel system. The fuelsystem is under pressure. There is

a risk of injury if the fuel system is leaking.

FUELQUALITY - PETROL

Note:We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.

CAUTION

Do not use leaded petrol or petrolwith additives containing othermetallic compounds (e.g.

manganese-based). They could damagethe emission system.

Useminimum95octane unleadedpetrol thatmeets the specification definedby EN228, or equivalent.

FUELQUALITY - E85

WARNINGSDo not modify the fuel systemconfiguration or the components inthe system.

Do not replace the fuel system orthe components with parts notspecially designed to be used with

E85.

CAUTIONSDo not use leaded petrol or petrolwith additives containing othermetallic compounds (e.g.

manganese-based). They could damagethe emission system.

Do not usemethanol instead of E85.

Note:We recommend that you use onlyhigh quality fuel without additives or otherengine treatments.

Note:When using E85, you mayexperience a higher fuel consumption.

Note: Your vehicle will operate well oncommercial quality 95 octane unleadedpetrol, but only high quality E85 offers thesame protection and performance.

Useminimum95octane unleadedpetrol thatmeets the specification definedby EN228, or equivalent. You can alsouse amixture of unleaded petrol and E85.

Long-termstorage

Due to small amounts of corrosiveimpurities that may be found in the E85,it is recommended that you fill the tankwith only 95 octane unleaded petrol priorto long-term storage of your vehicle.

FUELQUALITY - DIESEL

WARNING

Do not mix diesel with oil, petrol orother liquids. This could cause achemical reaction.

CAUTIONSDo not add kerosene, paraffin orpetrol to diesel. This could causedamage to the fuel system.

118

Fuel and refuelling

CAUTIONSUse diesel that meets thespecification defined by EN590, orthe relevant national specification.

Note:We recommend that you use onlyhigh quality fuel.

Note: The use of additives or otherengine treatments not approved by Fordis not recommended.

Note:We do not recommend theprolonged use of additives intended toprevent fuel waxing.

Long-termstorage

Most diesel fuels contain bio-diesel, it isrecommended to fill the tank with purelymineral diesel (where available) or add ananti-oxidant prior to long-term storage ofyour vehicle exceeding twomonths. Yourdealer can help you with a suitableanti-oxidant.

CATALYTICCONVERTER

WARNING

Do not park or idle your vehicle overdry leaves, dry grass or othercombustiblematerials. The exhaust

will radiate a considerable amount of heatduring use, and after you have switchedthe engine off. This is a potential firehazard.

Drivingwith a catalyticconverter

CAUTIONSAvoid running out of fuel.

Do not crank the engine for longperiods.

CAUTIONSDo not run the engine when a sparkplug lead is disconnected.

Do not push-start or tow-start yourvehicle. Use booster cables. SeeUsingboostercables (page 170).

Do not switch the ignition off whendriving.

FUEL FILLER FLAP

E78089

Note: Central locking also locks andunlocks the fuel filler flap. See Locks(page 32).

Open the flap fully until it engages. Turnthe fuel filler cap anti-clockwise.

When the filler cap is removed, a hissingnoise may be heard. This is normal andshould be disregarded.

To close, turn the cap clockwise until itclicks.

REFUELLING

CAUTION

Do not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the

engine. Have the system checked by aproperly trained technician immediately.

119

Fuel and refuelling

REFUELLING - E85

CAUTION

Do not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the

engine. Have the system checked by aproperly trained technician immediately.

After refuelling, allow 5minutes of normalengine operation above 48 km/h (30mph) to reduce the risk of an increasedengine restart time.

FUELCONSUMPTION

The CO2 and fuel consumption figuresare derived from laboratory testsaccording to EECDirective 80/1268/EECand subsequent amendments and arecarried out by all vehicle manufacturers.

They are intended as a comparisonbetween makes and models of vehicles.They are not intended to represent thereal world fuel consumption you may getfrom your vehicle. Real world fuelconsumption is governedbymany factorsincluding; driving style, high speed driving,stop/start driving, air conditioning usage,the accessories fitted and towing etc.

Your Ford dealer can give you advice onimproving your fuel consumption.

TECHNICALSPECIFICATIONS

Fuel consumption figures

CO2emis-sionsCombinedExtra-urbanUrban

Variant

g/kml/100 km(mpg)

l/100 km(mpg)

l/100 km(mpg)

1646.9 (40.9)5.7 (49.6)8.9 (31.7)1.6L Duratec Stage IV andV (74 kW)

1596.7 (42.2)5.3 (53.3)8.9 (31.7)1.6L Duratec Stage IV (85kW)

1697.1 (39.8)5.6 (50.4)9.6 (29.4)1.8L Duratec-HE Stage IV(92 kW)

1717.2 (39.2)5.5 (51.4)9.9 (28.5)2.0L Duratec-HE Stage IVand V (107 kW), manualtransmission

1898 (35.3)6.2 (45.6)11.2 (25.2)2.0L Duratec-HE Stage IV(107 kW), automatic trans-mission

120

Fuel and refuelling

CO2emis-sionsCombinedExtra-urbanUrban

Variant

g/kml/100 km(mpg)

l/100 km(mpg)

l/100 km(mpg)

1194.5 (62.8)3.7 (76.3)5.8 (48.7)1.6L Duratorq-TDCi StageIV (66 kW and 74 kW)

1435.4 (52.3)4.5 (62.8)6.9 (40.9)1.8L Duratorq-TDCi StageIV (85 kW)

1495.7 (49.6)4.7 (60.1)7.3 (38.7)2.0L Duratorq-TDCi StageIV (100 kW)

1595.9 (47.9)4.8 (58.9)8 (35.3)2.0L Duratorq-TDCi StageIV (81 kW and 100 kW),MPS6 transmission

121

Fuel and refuelling

MANUAL TRANSMISSION

CAUTION

Do not engage reverse gear whenthe vehicle ismoving. This can causedamage to the transmission.

E99067

On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.

AUTOMATICTRANSMISSION

WARNING

It is not possible to tow-start orpush-start a vehicle fitted with anautomatic transmission. SeeUsing

booster cables (page 170).

Selector lever positions

E78310

ParkP

ReverseR

NeutralN

DriveD

S mode and manual shiftingS

WARNING

Apply the brakes beforemoving theselector lever and keep themapplied until you are ready to move

off.

Note: A cold engine has a higher idlespeed. This will increase the tendency foryour vehicle to creep when you haveselected a drive gear.

Press the button on the selector lever toselect reverse and park.

The selector lever position will be shownin the information display.

Park

WARNINGSSelect park only when your vehicleis stationary.

122

Transmission

WARNINGSApply the parking brake andselect park before leavingyour vehicle. Make sure that the

selector lever is latched in position.

Note:An audiblewarningwill sound if youopen the driver's door and you have notselected park.

Note: The battery saver will deactivatethe warning chime after a period of time.

In this position, power is not transmittedto the drive wheels and the transmissionis locked. You can start the engine withthe selector lever in this position.

Reverse

WARNING

Select reverse only when yourvehicle is stationary and the engineis at idle speed.

Neutral

In this position, power is not transmittedto the drive wheels but the transmissionis not locked. You can start the enginewith the selector lever in this position.

Drive

Select drive to shift automatically throughthe forward gears.

The transmission will select theappropriate gear for optimumperformance based on ambienttemperature, road gradient, vehicle loadand driver input.

Kickdown

Press the accelerator pedal fully with theselector lever in the drive position to selectthe next lowest gear for optimumperformance. Release the acceleratorpedal when you no longer requirekickdown.

Manual shifting - Vehicleswitha 4F27E transmission

WARNING

Do not hold the selector leverpermanently in – or +.

CAUTION

The transmission will automaticallydownshift when the engine speed istoo low and upshift when too high.

Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.

Move the selector lever to position S.

Push the selector lever forwards to shiftdown and pull it backwards to shift up.

Gears may be skipped by moving theselector lever repeatedly at short intervals.

Manual mode also provides a kickdownfunction. See Kickdown.

Sportmodeandmanualshifting- Vehicleswith a 6DCT450transmission

Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.

Note: In Sportmode the transmissionoperates as normal but gears areselected more quickly and at higherengine speeds.

123

Transmission

Sportmode

Activate Sportmode by moving theselector lever to positionS.Sportmodewill remain active until either you shiftmanually up or down the gears or returnthe selector lever to position D.

Manual shifting

WARNING

Do not hold the selector leverpermanently in – or +.

CAUTION

The transmission will automaticallydownshift when the engine speed istoo low and upshift when too high.

Push the selector lever forwards to shiftdown and pull it backwards to shift up.

Gears may be skipped by moving theselector lever repeatedly at short intervals.

Manual mode also provides a kickdownfunction. See Kickdown.

Emergency park positionrelease lever

Use the lever to move the selector leverfrom the park position in the event of anelectrical malfunction or if your vehicle hasa flat battery.

E78321

CAUTION

Take care when lifting up the hingedcover.

Lift up the hinged cover in the centreconsole next to the selector lever with asmall flat bladed tool.

E78322

With a small flat bladed tool push downthe locking lever in the slot andsimultaneously move the selector leverout of the P position.

Note: If position P is selected again, thisprocedure must be repeated.

124

Transmission


Disc brakes

Wet brake discs result in reduced brakingefficiency. Dab the brake pedal whendriving froma carwash to remove the filmof water.

ABS

WARNING

The ABS does not relieve you ofyour responsibility to drive with duecare and attention.

TheABShelps you tomaintain full steeringand directional stability when you brakeheavily in an emergency, by preventingthe road wheels from locking.

HINTSONDRIVINGWITHABS

When the ABS is operating, the brakepedal will pulse. This is normal. Maintainpressure on the brake pedal.

The ABS will not eliminate the dangersinherent when:• you drive too close to the vehicle in

front of you.• the vehicle is aquaplaning.

• you take corners too fast.

• the road surface is poor.

PARKINGBRAKE

All vehicles

WARNING

Vehicles with an automatictransmission should always be leftwith the selector lever in positionP.

• Press the foot brake pedal firmly.

• Pull the parking brake lever up smartlyto its fullest extent.

• Do not press the release button whilepulling the lever up.

• If your vehicle is parked on a hill andfacing uphill, select first gear and turnthe steering wheel away from thekerb.

• If your vehicle is parked on a hill andfacing downhill, select reverse gearand turn the steering wheel towardsthe kerb.

To release the parking brake, press thebrake pedal firmly, pull the lever up slightly,depress the release button and push thelever down.

125

Brakes


Electronicstabilityprogramme(ESP)

WARNING

ESP does not relieve you of yourresponsibility to drive with due careand attention.

E72903

A A

AB

B

B

B

without ESPA

with ESPB

The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed bybraking individual wheels and reducingengine torque as needed.

The system also provides an enhancedtraction control function by reducingengine torque if thewheels spinwhen youaccelerate. This improves your ability topull away on slippery roads or loosesurfaces, and improves comfort by limitingwheel spin in hairpin bends.

Stabilitycontrol(ESP)warninglamp

The ESPwarning lampwill flash when thesystem is operating. SeeWarninglamps and indicators (page 65).

Emergency brake assist

WARNING

Emergency brake assist does notrelieve you of your responsibility todrive with due care and attention.

Emergency brake assist will detect whenyou brake heavily by measuring the rateat which you press the brake pedal. It willprovide maximum braking efficiency aslong as you press the pedal. Emergencybrake assist can reduce stoppingdistances in critical situations.

USINGSTABILITYCONTROL

Note: The system will be switched onautomatically every time you switch theignition on.

To turn the system off and on. SeeInformation displays (page 69).

126

Stability control


WARNING

The parking aid does not relieve youof your responsibility to drive withdue care and attention.

CAUTIONSVehicles fitted with a trailer towmodule not approved by usmay notcorrectly detect obstacles.

The sensors may not detect objectsin heavy rain or other conditions thatcause disruptive reflections.

The sensors may not detect objectswith surfaces that absorb ultrasonicwaves.

The parking aid does not detectobstacles moving away from thevehicle. They will only be detected

shortly after they start to move towardsthe vehicle again.

Take particular care when reversingwith a tow ball arm or rear fittedaccessories e.g. a bicycle carrier, as

the rear parking aid will only indicate thedistance from thebumper to theobstacle.

If you use a high pressure spray towash your vehicle, only spray thesensors briefly from a distance not

less than 20 centimetres (8 inches).

Note: On vehicles fitted with a tow ballarm, the parking aid is deactivatedautomatically when any trailer lamps (orlighting boards) are connected to the13-pin socket via a trailer tow module wehave approved.

Note: Keep the sensors free from dirt,ice and snow. Do not clean with sharpobjects.

Note: The parking aid may emit falsetones if it detects a signal using the samefrequency as the sensors or if the vehicleis fully laden.

Note: The outer sensorsmay detect theside walls of a garage. If the distancebetween the outer sensor and the sidewall remains constant for three seconds,the tone will switch off. As you continue,the inner sensors will detect rearwardobjects.

USINGTHEPARKINGAID

Switching the parking aid onand off

Note: The parking aid switches offautomatically when you start the engineor when you exceed 16 km/h (10 mph).

Note: The front and rear sensors arealways activated or deactivated together.

The parking aid is per default off. Toswitch the parking aid on, press the switchin the instrument panel or select reversegear.

The light in the switch illuminates whenthe parking aid is activated.

To turn it off, press the switch again.

Manoeuvringwith the parkingaid

E72902

127

Parking aid

Note: If a high pitchwarning tone soundsfor three seconds and the light in theswitch is flashing, it indicates amalfunction. The system will be disabled.Have the system checked by properlytrained technicians.

You will hear an intermittent tone at adistance of up to approximately 150centimetres (59 inches) between theobstacle and rear bumper, 80 centimetres(31 inches) between the obstacle andfront bumper and 50 centimetres (20inches) to the side. Decreasing thedistance accelerates the intermittent tone.A continuous tone will start at a distanceof less than 30 centimetres (12 inches).

You will hear an alternating tone from thefront and rear if obstacles are closer than30 centimetres (12 inches) to the frontand rear bumpers.

128

Parking aid


The camera is a visual aid for use whenreversing.

WARNING

The camera does not relieve you ofyour responsibility to drive with duecare and attention.

CAUTIONSIf you use a high pressure spray towash your vehicle, only spray thecamera briefly from a distance not

less than 20 centimetres (8 inches).

Do not apply pressure to the camera.The position and the angle of thecamera automatically changes.

Note: Keep the camera free from dirt,ice and snow. Do not clean with sharpobjects, degreaser, wax or organicproducts. Use only a soft cloth.

During operation, guide lines appear inthe displaywhich represent your vehicle'spath and approximate distance fromrearward objects.

USINGTHEREARVIEWCAMERA

WARNINGSThe operation of the camera mayvary depending on the ambienttemperature, vehicle and road

conditions.

The distances shown in the displaymay differ from the actual distance.

Do not place objects in front of thecamera.

The camera is located on the luggagecompartment lid near the handle.

E99105

Activatingtherearviewcamera

CAUTION

The camera may not detect objectsthat are close to the vehicle.

With the ignition and the audio unitswitched on, engage reverse gear. Theimage is displayed on the screen.

The camera may not operate correctly inthe following conditions:• Dark areas.

• Intense light.

• If the ambient temperature increasesor decreases rapidly.

• If the camera is wet, for example inrain or high humidity.

• If the camera's view is obstructed, forexample by mud.

Using the display

CAUTIONSObstacles above the camerapositionwill not be shown. Inspect the areabehind your vehicle if necessary.

129

Rear viewcamera

CAUTIONSMarks are for general guidance only,and are calculated for vehicles inmaximum loadconditions on aneven

road surface.

The lines show a projected vehicle path(based on the current steering wheelangle) and the distance from the exteriormirrors and rear bumper.

E99458

A

B

C

D

A

B

C

D

Exterior mirror clearance - 0.1metre (4 inches)

A

Red - 0.3 metre (12 inches)B

Yellow - 1 metre (39 inches)C

Yellow - 2 metres (79 inches)D

130

Rear viewcamera

The green line shows the centre line ofthe projected vehicle path.

Note:When reversing with a trailer, thelines on the screen show the vehicledirection and not the trailer.

Deactivating the rear viewcamera

Note: Disengage reverse gear. Thedisplay will stay on for a short periodbefore switching off.

The system will automatically switch offonce the vehicle speed has reachedapproximately 15 km/h (9 mph).

Vehicleswith parking aid

The display will additionally show acoloured distance bar. This guideindicates the distance from the rearbumper to the detected obstacle.

These are colour coded as follows:• Green - 0.8 to 1.5 metres (31 to 59

inches).• Yellow - 0.3 to 0.8 metre (12 to 31

inches).• Red - 0.3 metre (12 inches) or less.

131

Rear viewcamera


Cruise control allows you to control yourspeed using the switches on the steeringwheel. You can use cruise control whenyou exceed approximately 30 km/h (20mph).

USINGCRUISECONTROL

WARNING

Do not use cruise control in heavytraffic, on twisty roads or when theroad surface is slippery.

Switching cruise control on

E75456

Note: The system is ready for you to seta speed.

Setting a speed

E75452

Press to store and maintain your currentspeed. The cruise control indicator willilluminate. SeeWarning lamps andindicators (page 65).

Changing the set speed

WARNING

When you are going downhill, yourspeed may increase above the setspeed. The systemwill not apply the

brakes. Change down a gear and pressthe SET- switch to assist the system inmaintaining the set speed.

Note: If you accelerate by pressing theaccelerator pedal, the set speed will notchange. When you release theaccelerator pedal, you will return to thespeed that you previously set.

132

Cruise control

E95393

A

B

AccelerateA

DecelerateB

Cancelling the set speed

E75453

Press the brake pedal or theRES switch.

Note: The system will no longer controlyour speed. The cruise control indicatorwill not illuminate but the systemwill retainthe speed that you previously set.

Resuming the set speed

E75453

The cruise control indicator will illuminateand the system will attempt to resumethe speed that you previously set.

Switching cruise control off

E75455

The system will not retain the speed thatyou previously set. The cruise controlindicator will not illuminate.

133

Cruise control

GENERAL INFORMATION

WARNINGSUse load securing straps to anapproved standard, e.g. DIN.

Make sure that you secure all looseitems properly.

Place luggage and other loads aslow and as far forward as possiblewithin the luggage or loadspace.

Do not drive with the tailgate or reardoor open. Exhaust fumes mayenter the vehicle.

Do not exceed the maximum frontand rear axle loads for your vehicle.SeeVehicle identification (page

183).

Heavy loads, when placed in thepassenger compartment, should beon folded rear seats as shown. See

Rear seats (page 96).

CAUTIONSDonot allow items to contact the rearwindows.

Do not use any abrasive materials toclean the interior of the rearwindows.

Do not install stickers or labels to theinterior of the rear windows.

E98627

LUGGAGECOVERS

E78092

WARNING

Donot place objects on the luggagecover.

Note:When moving the rear seats intothe comfort position, fold back the coverfrom the front edge.

Detach the two lifting straps on thetailgate. Fold back the cover from thefront edge. Release the cover from itsretaining points and lift it out.

134

Load carrying

When reinstalling it, ensure that it isproperly secured at the retaining points.

REARUNDERFLOORSTORAGE

WARNING

When you are using a child seatwitha support leg, remove the storagecompartment cover and extend the

leg to the base of the compartment.

E78097

135

Load carrying

TOWINGATRAILER

WARNINGSDo not exceed 100 km/h (62 mph).

The rear tyre pressures must beincreased by 0.2 bar (3 psi) abovespecification. See Technical

specifications (page 181).

Do not exceed themaximumgrosstrain weight stated on the vehicleidentification plate. See Vehicle

identification (page 183).

CAUTION

Do not exceed the maximumpermissible nose weight, i.e. verticalweight on the tow ball, of 75

kilogrammes (165 pounds).

Note: Not all vehicles are suitable orapproved to have tow bars fitted. Checkwith your dealer first.

Place loads as low and central to theaxle(s) of the trailer as possible. If you aretowing with an unladen vehicle, the loadin the trailer should be placed toward thenose, within the maximum nose load, asthis gives the best stability.

The stability of the vehicle to trailercombination is very much dependant onthe quality of the trailer.

In high altitude regions above 1 000metres (3 281 feet), the stipulatedmaximum permitted gross train weightmust be reduced by 10% for everyadditional 1 000 metres (3 281 feet).

Steep gradients

WARNING

The overrun brake on a trailer is notcontrolled by ABS.

Change down a gear before you reach asteep downhill gradient.

DETACHABLE TOWBALL

WARNINGSWhen not in use, always transportthe tow ball arm securely fastenedin the luggage compartment.

Take special care when fitting thetow ball arm as the safety of thevehicle and the trailer depends on

this.

Do not use any tools for mountingor dismounting the tow ball arm. Donot modify the trailer coupling. Do

not disassemble or repair the towball arm.

E71328

136

Towing

Unlocking the towball armmechanism

E99477

1

2

1. Detach the keyhole protective cap.2. Insert the key and turn it

anti-clockwise to unlock (1).3. Hold the tow ball arm. Pull the

handwheel out and turn it clockwiseuntil it clicks (2).

4. The redmark on the handwheelmustalign with thewhitemark on the towball.

5. Release the handwheel. The tow ballarm is unlocked.

Inserting the towball arm

WARNING

The tow ball arm may only beinsertedwhencompletely unlocked.

E99484

1

3

2

1. Pull out the plug (1).2. Insert the tow ball arm vertically and

press it upwards until it engages (2).Do not hold your hand near thehandwheel.

3. The greenmark on the handwheelmust align with thewhite dot on thetow ball.

4. To lock, turn the key clockwise andremove the key (3).

5. Attach the keyhole protective cap.

137

Towing

Drivingwith a trailer

E71331

A

B

WARNING

If any of the below conditionscannot be met, do not use the towbar and have it checked by a

properly trained technician.

Before starting your journey, make surethat the tow ball arm is properly locked.Check:

• The greenmark on the handwheelis aligned with thewhite dot on thetow ball arm.

• the handwheel (A) is correctly fittedto the tow ball arm.

• you have removed the key (B).• the towball arm is securely positioned.

It must not move when jerked.

Removing the towball arm

WARNING

Never unlock the tow ball arm withthe trailer attached.

E99485

4

1

3

2

1. Unhitch the trailer.2. Detach the keyhole protective cap.3. Insert the key and turn it

anti-clockwise to unlock (1).4. Hold the tow ball arm. Pull the

handwheel out, turn it clockwiseagainst the stop (2) and remove thetow ball arm (3).

5. Release the handwheel.

When unlocked in this way, the tow ballarm can be reinserted at any time.

Insert the plug into its seat (4).

Maintenance

WARNING

Remove the tow ball arm andprotect the seatwith the plug beforesteam cleaning your vehicle.

138

Towing

Keep the system clean. Periodicallylubricate bearings, sliding surfaces, andlocking balls with resin-free grease or oiland the lock with graphite.

Keep a note of the key number. In caseof loss, replacement keys are availablefrom the manufacturer by stating thethree digit key number.

139

Towing

RUNNING-IN

Tyres

WARNING

New tyres need to be run-in forapproximately 500 kilometres (300miles). During this time, you may

experience different drivingcharacteristics.

Brakes and clutch

WARNING

Avoid heavy use of the brakes andclutch if possible for the first 150kilometres (100 miles) in town and

for the first 1 500 kilometres (1 000 miles)on motorways.

Engine

CAUTION

Avoid driving too fast during the first1 500 kilometres (1 000 miles). Varyyour speed frequently and change

up through the gears early. Do not labourthe engine.

COLDWEATHERPRECAUTIONS

The functional operation of somecomponents and systems can beaffected at temperatures below -30°C(-22°F).

DRIVINGTHROUGHWATER

Driving throughwater

CAUTIONSDrive throughwater in an emergencyonly, and not as part of normaldriving.

Engine damage can occur if waterenters the air filter.

In an emergency, the vehicle can bedriven throughwater to amaximumdepthof 200 mm and at a maximum speed of10 km/h (6mph). Extra caution should beexercised when driving through flowingwater.

When driving in water, maintain a lowspeed and do not stop the vehicle. Afterdriving through water, and as soon as itis safe to do so:• Depress the brake pedal lightly and

check that full brake function isachieved.

• Check that the horn works.

• Check that the vehicle's lights are fullyoperational.

• Check the power assistanceof the steering system.

140

Driving hints

FIRSTAIDKIT

E78361

Space is provided in the luggagecompartment.

WARNINGTRIANGLE

Space is provided under the driver’s seat.

141

Emergency equipment

FUELCUT-OFFSWITCH

VehicleswithaDuratecengine

E72531

The fuel supply may be cut off as a resultof an accident or sudden vibrations (e.g.collision when parking).

The switch is located in the side panel infront of the driver's door.

Resetting the switch

WARNING

Do not reset the fuel cut-off switchif you see or smell leaking fuel.

• Turn the ignition switch to position 0.• Check fuel system for leaks.

• If no fuel leak is apparent, reset theswitch by pushing in the button (seeillustration).

• Turn the ignition switch to position II.After a few seconds return the key toposition I.

• Make a further check for leaks in thefuel system.

142

Status after a collision

FUSEBOXLOCATIONS

Engine compartment fuse box

E78332

Passenger compartment fusebox

1. Remove the screws in the instrumentpanel trim underneath the glovecompartment and lower the trimpanel.

2. Loosen the screws.

3. Lower the fuse box andpull it towardsyou.

Install in the reverse order.

CHANGINGAFUSE

WARNINGSDo not modify the electrical systemof your vehicle in any way. Haverepairs to the electrical system and

the replacement of relays andhigh currentfuses carried out by properly trainedtechnicians.

Switch the ignition and all electricalequipment off before touching orattempting to change a fuse.

CAUTION

Fit a replacement fusewith the samerating as the one you have removed.

Note: You can identify a blown fuse bya break in the filament.

Note:All fuses, except high current fusesare a push fit.

Note: A fuse puller is located in the lid ofthe engine compartment fuse box.

FUSE LABELS

The fuse chart label shows rectanglesrepresenting a fuse or relay. The followinginformation is shown in the rectangles:

E78342

B

A C

Symbol of the functionA

Number of the fuseB

Ampere rating of the fuseC

See Owner’s handbook

Cooling fan

Power steering

Central fuse box, ignition relays

143

Fuses

Diesel pre-glow

ABS module, ABS/ESPpumps/valves

Engine management orelectronic module

Heater blower

Heated windscreen

PTC heater (vehicles with adiesel engine)

Injectors, ignition transformers

Headlamp washer

Horn

Diesel fuel heater

Air conditioning

Battery sense smart charging

Central locking, ignition switch

Electric parking brake (EPB)

144

Fuses

FUSESPECIFICATIONCHART

Engine compartment fuse box

E79716

19

6

7 8

10

9

12

11

14

13

16

15

29 36

28

34

35

33

22 25 325

4

3

2

1

2017

18

2421 30 31

23 26 27

Circuits protectedAmpereratingFuse

Cooling fan401

Power steering802

Passenger compartment fuse box supply 1603

Passenger compartment fuse box supply 2604

Auxiliary heater805

Glow plug (diesel only)606

ABS, stability control pump307

ABS, stability control valves208

Powertrain control module209

Climate control blower3010

Ignition switch2011

145

Fuses

Circuits protectedAmpereratingFuse

Ignition relay 15l4012

Starter solenoid2013

Heated windscreen, right-hand side4014

Cooling fan relay (Sigma - non A/C only)3015

Heated windscreen, left-hand side4016

Not used-17

Power inverter3018

ABS module1019

Horn1520

Auxiliary heater2021

Power steering module1022

Headlamp washer3023

Auxiliary heater (diesel only)1524

Ignition, relays1025

Automatic transmission1526

Air conditioning clutch1027

Glow plug monitoring (diesel only)1028

Dual zone climate control1029

Powertrain control module, automatic transmission330

Battery sensor smart charging1031

Automatic transmission1032

Heated oxygen sensors (petrol only)1033

Intercooler bypass valve (diesel only)1033

Injectors, ignition transformers1034

Powertrain control module, valves, solenoids1035

Powertrain control module1036

146

Fuses

Passenger compartment fuse box

100

101102

103

104

138139

140

141142

143

105

111

117

123

130

132

133

129

134

135

136

137

131

106

112

118

124

109

115

121

127

110

116

122

128

107

113

119

125

108

114

120

126

E88709

Circuits protectedAmpere ratingFuse

Electronic modules ignitionsupply10100

Electric sunroof controlmodule, driver’s electricseat,

20101

Heater control, steeringcolumn, diesel particulatefilter, remote controlreceiver

10102

Lighting control batterysupply10103

Battery saver, interior lamps10104

Heated rear window25105

Keyless system20106

Instrument cluster batterysupply, on-boarddiagnostics

10107

147

Fuses


Accessory to cluster (audioand navigation unit)7.5108

Cigar lighter, rear auxiliarypower socket20109

Daytime running lamps igni-tion supply to lightingcontrol switch

10110

Fuel pump (petrol engineonly)15111

Audio modules batterysupply15112

Daytime running lamps(parking lamps)10113

Instrument cluster ignitionsupply, engine immobiliser10114

Lighting control ignitionsupply7.5115

Fog lamps20116

Number plate lamps7.5117

Doormodule, left-hand rear20118

Luggage compartmentauxiliary power socket15119

Luggage compartmentauxiliary power socket(vehicles with trailer towmodule)

25119

Door module, right-handrear20120

Heated front seats20121

Airbag module10122

Heated exterior mirrors7.5123

Parking lamps, side lamps,tail lamps (left-hand side)7.5124

148

Fuses


Parking lamps, side lamps,tail lamps (right-hand side)7.5125

Keyless system20126

Electric windows25127

Not used-128

Windscreen wipers20129

Not used-130

Rear window wiper15131

Brake lamps15132

Central locking relays,passenger door module25133

Central locking, driver doormodule20134

Daytime running lamps20135

Washer pump, heatedwasher jets15136

Battery backup sounder10137

Powertrain control module,accelerator pedal, auto-matic transmission

10138

Main beam right-hand side10139

Main beam left-hand side10140

Reversing lamp, electricmirrors10141

Dipped beam, right-handside15142

Dipped beam, left-handside15143

149

Fuses

TOWINGPOINTS

Towing eye location

E78366

E89126

The screw-in towing eye is located eitherin the left-hand side trim in the luggagecompartment or in the underfloor storagecompartment under the spare wheel.

The towing eye must always be carriedin the vehicle.

Installing the towing eye

CAUTION

The screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it. Make sure

that the towing eye is fully tightened.

Note: On vehicles with a tow bar, thetowing eye cannot be installed at the rearof the vehicle. Use the tow bar to tow avehicle.

Front towing eye

E78367

150

Vehicle recovery

Rear towing eye

E78368

Insert a suitable object into the hole onthe underside of the cover and prise offthe cover.

Install the towing eye.

TOWINGTHEVEHICLEONFOURWHEELS

All vehicles

WARNINGSSwitch the ignition on when yourvehicle is being towed. The steeringlock will engage and the direction

indicators and brake lamps will not workif you do not.

The brake servo and the powersteering pump do not operateunless the engine is running. Press

the brake pedal harder and allow forincreased stopping distances and heaviersteering.

CAUTIONSToo much tension in the tow ropecould cause damage to your vehicleor the vehicle that is towing.

Do not use a rigid tow bar on thefront towing eye.

Drive off slowly and smoothly withoutjerking the vehicle that is towing.


CAUTIONSDo not tow your vehicle faster than50 km/h (30 mph) or further than 50kilometres (30 miles). On vehicles

with a 6DCT450 transmission, do not towyour vehicle faster than 30 km/h (18mph).

If the stated speed or distance is tobe exceeded the drive wheels mustbe lifted clear of the ground.

In the event of a mechanical failureof the transmission the drive wheelsmust be lifted clear of the ground.

Do not tow your vehicle backwards.

Select neutral when your vehicle isbeing towed.

151

Vehicle recovery

GENERAL INFORMATION

Have your vehicle serviced regularly tohelp maintain its roadworthiness andresale value. There is a large network ofFord Authorised Repairers that are thereto help you with their professionalservicing expertise. We believe that theirspecially trained technicians are bestqualified to service your vehicle properlyand expertly. They are supported by awide range of highly specialised toolsdeveloped specifically for servicing yourvehicle.

In addition to regular servicing, werecommend that you carry out thefollowing additional checks.

WARNINGSSwitch the ignition off beforetouching or attempting adjustmentof any kind.

Do not touch the electronic ignitionsystem parts after you haveswitched the ignition on orwhen the

engine is running. The system operatesat high voltage.

Keep your hands and clothing clearof the engine cooling fan. Undercertain conditions, the fan may

continue to run for several minutes afteryou have switched the engine off.

CAUTION

When carrying out maintenancechecks,make sure that filler caps arefitted securely.

Daily checks

• Exterior lamps.

• Interior lamps.

• Warning lamps and indicators.

Checkwhen refuelling

• Engine oil level. See Engine oilcheck (page 162).

• Brake fluid level. See Brake andclutch fluid check (page 163).

• Washer fluid level. SeeWasherfluidcheck (page 164).

• Tyre pressures (when cold). SeeTechnical specifications (page181).

• Tyre condition. SeeTyrecare (page180).

Monthly checks

• Engine coolant level (engine cold).See Engine coolant check (page163).

• Pipes, hoses and reservoirs for leaks.

• Power steering fluid level. SeePowersteeringfluidcheck (page164).

• Air conditioning operation.

• Parking brake operation.

• Horn operation.

• Tightness of wheel nuts. SeeTechnical specifications (page181).

OPENINGANDCLOSINGTHEBONNET

Opening the bonnet

WARNING

To prevent damage to, or loss of thekey, remove the key immediatelyafter opening and swivel the Ford

badge back.

Note:On vehicleswith keyless entry, usethe spare key. SeeKeylessentry (page34).

152

Maintenance

1

E78141

E78142

2 3

5

4

E78143

Closing the bonnet

Note:Make sure that the bonnet isclosed properly.

Lower the bonnet and allow it to dropfrom under its own weight for the last 20– 30 centimetres (8 - 12 inches).

153

Maintenance

ENGINECOMPARTMENTOVERVIEW - 1.6LDURATEC-16V(SIGMA)/1.6LDURATEC-16V TI-VCT (SIGMA)

IJ

FEDCBA

H GE78887

Screen washer fluid reservoir*: SeeWasher fluid check (page 164).A

Engine coolant reservoir*: See Engine coolant check (page 163).B

Brake and clutch fluid reservoir (right-hand drive)*: See Brake and clutchfluid check (page 163).

C

Engine oil filler cap*: See Engine oil check (page 162).D

Brake and clutch fluid reservoir (left-hand drive)*: See Brake and clutchfluid check (page 163).

E

154

Maintenance

Battery: See Vehicle battery (page 170).F

Engine compartment fuse box: See Fuses (page 143).G

Air cleaner: No maintenance necessary.H

Engine oil dipstick*: See Engine oil check (page 162).I

Power steering fluid reservoir: See Power steering fluid check (page164).

J

*For easy identification, filler caps and the engine oil dipstick are marked in colour.

155

Maintenance

ENGINECOMPARTMENTOVERVIEW - 1.8LDURATEC-HE(MI4)/2.0LDURATEC-HE (MI4)

E78889

I

FEDCBA

H G




C



E

156

Maintenance




Engine oil dipstick*: See Engine oil check (page 162).I*For easy identification, filler caps and the engine oil dipstick are marked in colour.

ENGINECOMPARTMENTOVERVIEW-1.6LDURATORQ-TDCI(DV) DIESEL

E78891

I

FEDCBA

H G

157

Maintenance




C



E





158

Maintenance

ENGINECOMPARTMENTOVERVIEW-1.8LDURATORQ-TDCI(LYNX) DIESEL

E78892

I

FEDCBA

H G




C



E

159

Maintenance





ENGINECOMPARTMENTOVERVIEW - 2.0LDURATORQ-TDCI (DW)DIESEL

E78893

I

FEDCBA

H G

160

Maintenance




C



E





ENGINEOILDIPSTICK - 1.6LDURATEC-16V(SIGMA)/1.6LDURATEC-16V TI-VCT(SIGMA)

E95540

BA

MINA

MAXB

ENGINEOILDIPSTICK - 1.8LDURATEC-HE (MI4)/2.0LDURATEC-HE (MI4)

E92036

A B

MINA

MAXB

161

Maintenance

ENGINEOILDIPSTICK - 1.6LDURATORQ-TDCI (DV)DIESEL

E90983

A B

MINA

MAXB

ENGINEOILDIPSTICK - 1.8LDURATORQ-TDCI (LYNX)DIESEL

E95527

B

A

MINA

MAXB

ENGINEOILDIPSTICK-2.0LDURATORQ-TDCI (DW)DIESEL

E95543

BA

MINA

MAXB

ENGINEOILCHECK

CAUTION

Do not use oil additives or otherengine treatments. Under certainconditions, they could damage the

engine.

Note: The oil consumption of newengines reaches its normal level afterapproximately 5 000 kilometres (3 000miles).

Checking the oil level

CAUTION

Make sure that the level is betweentheMIN and theMAXmarks.

Note:Check the level before starting theengine.

Note:Make sure that your vehicle is onlevel ground.

Note:Oil expandswhen it is hot. The levelmay therefore extend a few millimetresbeyond theMAXmark.

162

Maintenance

Remove the dipstick and wipe it with aclean, lint free cloth. Replace the dipstickand remove it again to check the oil level.

If the level is at theMINmark, top upimmediately.

Topping up

WARNINGSOnly top upwhen the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.

Do not remove the filler cap whenthe engine is running.

Remove the filler cap.

CAUTION

Do not top up further than theMAXmark.

Top up with fluid that meets the Fordspecification. See Technicalspecifications (page 165).

ENGINECOOLANTCHECK

Checking the coolant level

WARNING

Do not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with

plenty of water and contact your doctor.

CAUTION

Make sure that the level is betweentheMIN and theMAXmarks.

Note: Coolant expands when it is hot.The level may therefore extend beyondtheMAXmark.

If the level is at theMINmark, top upimmediately.

Topping up

WARNINGSOnly top upwhen the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.

Do not remove the filler cap whenthe engine is running.

Do not remove the filler cap whenthe engine is hot.Wait for the engineto cool down.

Unscrew the cap slowly. Any pressurewill escape slowly as you unscrew thecap.

CAUTIONSDo not spill coolant on any part of theengine.

Do not top up further than theMAXmark.


BRAKEANDCLUTCHFLUIDCHECK

WARNINGSDo not allow the fluid to touch yourskin or eyes. If this happens, rinsethe affected areas immediately with

plenty of water and contact your doctor.

If the level is at theMINmark, havethe system checked by a properlytrained technician as soon as

possible.

163

Maintenance

Note: The brake and the clutch systemsare supplied from the same reservoir.


POWERSTEERINGFLUIDCHECK

Vehicleswith1.6LDuratec-16V(Sigma)or1.6LDuratec-16VTi-VCT (Sigma) engine

E73701

The fluid level should come up to theMAXmark when the engine is cold.

If it drops below theMINmark, top upwith the specified fluid. See Technicalspecifications (page 165).

All except vehicleswith 1.6LDuratec-16V (Sigma) or 1.6LDuratec-16V Ti-VCT (Sigma)engine

No fluid level checks are necessary.

WASHERFLUIDCHECK

The front and rear washer systems aresupplied from the same reservoir.

164

Maintenance


Vehicle fluids

SpecificationRecommended fluidItem

WSS-M2C913-CCastrol Engine Oil*Engine oil

WSS-M2C204-A2Ford or Motorcraft PowerSteering FluidPower steering fluid

WSS-M97B44-DMotorcraft SuperPlus Anti-freezeAntifreeze

ESD-M6C57-AFord or Motorcraft SuperDOT 4 Brake FluidBrake fluid

* Providing it meets the specification defined byWSS-M2C913-C, you can also useFord Engine Oil or an alternative engine oil.

Toppinguptheoil: If you are unable to find an oil thatmeets the specification definedbyWSS-M2C913-C, you must use SAE5W-30 (preferred), SAE5W-40 (exceptvehicles with E85 fuel) or SAE 10W-40 that meets the specification defined by eitherACEAA5/B5 (preferred) orACEAA3/B3. Using these oils can result in longer enginecranking periods, reduced engine performance, reduced fuel economy and increasedemission levels.

Castrol engine oil recommended.

E115472

Capacities

Capacity in litres(gallons)ItemVariant

MAX-markPower assisted steeringfluidAll

55 (12.1)Fuel tankVehicles with a petrolengine

55 (12.1)Fuel tankVehicles with a dieselengine

4.0 (0.9)Windscreenwasher systemAll

4.1 (0.9)Engine oil - with filter1.6L Duratec-16V

165

Maintenance

Capacity in litres(gallons)ItemVariant

3.75 (0.8)Engine oil - without filter1.6L Duratec-16V

5.5 (1.2)Cooling system includingheating - vehicles withoutair conditioning

1.6L Duratec-16V

5.8 (1.3)Cooling system includingheating - vehicles with airconditioning

1.6L Duratec-16V

4.1 (0.9)Engine oil - with filter1.6L Duratec-16V Ti-VCT

3.75 (0.8)Engine oil - without filter1.6L Duratec-16V Ti-VCT

6.0 (1.3)Cooling system includingheating1.6L Duratec-16V Ti-VCT

4.3 (0.9)Engine oil - with filter1.8L Duratec-HE

3.9 (0.9)Engine oil - without filter1.8L Duratec-HE

6.5 (1.4)Cooling system includingheating1.8L Duratec-HE

4.3 (0.9)Engine oil - with filter2.0L Duratec-HE

3.9 (0.9)Engine oil - without filter2.0L Duratec-HE

6.3 (1.4)Cooling system includingheating2.0L Duratec-HE

3.8 (0.8)Engine oil - with filter1.6L Duratorq-TDCi

3.4 (0.7)Engine oil - without filter1.6L Duratorq-TDCi

7.3 (1.6)Cooling system includingheating1.6L Duratorq-TDCi







166

Maintenance

Engine oil top up capacities

Capacity in litres(gallons)Engine

0.7 (0.2)1.6L Duratec-16V, 1.6L Duratec-16V Ti-VCT, 1.8L Duratec-HE and 2.0L Duratec-HE

1.6 (0.4)1.6L Duratorq-TDCi

1 (0.2)1.8L Duratorq-TDCi

1.8 (0.4)2.0L Duratorq-TDCi

167

Maintenance

CLEANINGTHEEXTERIOR

WARNING

If you use a car wash with a waxingcycle, make sure that you removethe wax from the windscreen.

CAUTIONSPrior to using a car wash facilitycheck the suitability of it for yourvehicle.

Some car wash installations usewater at high pressure. This coulddamage certain parts of your vehicle.

Remove the aerial before using anautomatic car wash.

Switch the heater blower off toprevent contamination of the freshair filter.

We recommend that you wash yourvehicle with a sponge and lukewarmwater containing a car shampoo.

Cleaning the headlamps

CAUTIONSDo not scrape the headlamp lensesor use abrasives, alcoholic solventsor chemical solvents to clean them.

Do not wipe the headlamps whenthey are dry.

Cleaning the rearwindow

CAUTION

Do not scrape the inside of the rearwindowor use abrasives or chemicalsolvents to clean it.

Use a clean, lint free cloth or a dampchamois leather to clean the inside of therear window.

Cleaning the chrome trim

CAUTION

Do not use abrasives or chemicalsolvents. Use soapy water.

Body paintwork preservation

CAUTIONSDo not polish your vehicle in strongsunshine.

Do not allow polish to touch plasticsurfaces. It could be difficult toremove.

Donot apply polish to thewindscreenor rear window. This could cause thewipers to become noisy and they

may not clear the window properly.

We recommend that you wax thepaintwork once or twice a year.

CLEANINGTHE INTERIOR

Seat belts

WARNINGSDo not use abrasives, or chemicalsolvents to clean them.

Do not allow moisture to penetratethe seat belt retractor mechanism.

Clean the seat belts with interior cleaneror water applied with a soft sponge. Letthe seat belts dry naturally, away fromartificial heat.

168

Vehicle care

Instrument cluster screens,LCD screens, radio screens

WARNING

Do not use abrasives, alcoholicsolvents or chemical solvents toclean them.

REPAIRINGMINORPAINTDAMAGE

CAUTION

Removeapparently harmless lookingsubstances from the paintworkimmediately (e.g. bird droppings, tree

resins, insect remains, tar spots, road saltand industrial fall out).

You should repair paintwork damagecaused by stones from the road or minorscratches as soon as possible. A choiceof products is available from your FordDealer. Read and follow themanufacturer’s instructions.

169

Vehicle care

USINGBOOSTERCABLES

CAUTIONSConnect batterieswith only the samenominal voltage.

Always use booster cables withinsulated clamps and adequate sizecable.

Do not disconnect the battery fromthe vehicle’s electrical system.

Toconnect thebooster cables

A

B

C D

E102925

Flat battery vehicleA

Booster battery vehicleB

Positive connection cableC

Negative connection cableD

1. Position the vehicles so that they donot touch one another.

2. Switch off the engine and anyelectrical equipment.

3. Connect the positive (+) terminal ofvehicleBwith the positive (+) terminalof vehicle A (cable C).

4. Connect the negative (-) terminal ofvehicleB to the ground connection ofvehicle A (cable D). See Batteryconnection points (page 171).

CAUTIONSDonotconnect to thenegative(–) terminal of the flat battery.

Make sure that the cables are clearof any moving parts.

To start the engine

1. Run the engine of vehicle B atmoderately high speed.

2. Start the engine of vehicle A.3. Run both vehicles for a minimum of

three minutes before disconnectingthe cables.

CAUTION

Do not switch on the headlampswhen disconnecting the cables. Thepeak voltage could blow the bulbs.

Disconnect the cables in the reverseorder.

170

Vehicle battery

BATTERYCONNECTIONPOINTS

E114494

CAUTION

Donotconnect to thenegative(–) terminal of the flat battery.

171

Vehicle battery

GENERAL INFORMATION

CAUTIONSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make

the National Type Approval invalid.

If you change the diameter of thetyres from that fitted at the factory,the speedometer may not display

the correct speed. Take the vehicle toyour dealer to have the enginemanagement system reprogrammed.

A decal with tyre pressure data is locatedin the driver’s door opening at the B-pillar.

Check and set the tyre pressure at theambient temperature in which you areintending to drive the vehicle and whenthe tyres are cold.

CHANGINGAROADWHEEL

Lockingwheel nuts

You can obtain a replacement lockingwheel nut key and replacement lockingwheel nuts from your dealer using thereference number certificate.

Vehicleswith a temporarysparewheel

WARNINGSIf the spare wheel differs from theother fittedwheels, these rulesmustbe followed:

Do not exceed 80 km/h (50 mph).

Drive the shortest possibledistances.

Do not fit more than one sparewheel on your vehicle at any onetime.

WARNINGSDonot use snowchains on this typeof wheel.

Do not drive through an automaticcar wash.

Do not carry out any tyre repairs ona temporary spare wheel.

CAUTION

The ground clearance of your vehiclewill be reduced. Take care whenparking next to a kerb.

Note: Your vehicle may exhibit someunusual driving characteristics.

Vehicle jack

WARNINGSThe vehicle jack supplied with yourvehicle should only be used whenchanging a wheel in emergency

situations.

Before using the vehicle jack, checkthat it is not damaged or deformedand that the thread is lubricated and

free from foreign matter.

Never place anything between thejack and the ground, or the jack andthe vehicle.

Note: Vehicles with a tyre repair kit arenot equipped with a vehicle jack or awheel brace.

It is recommended to use a workshoptype hydraulic jack for changing betweensummer and winter tyres.

Note: Use a jack with a minimum liftingcapacity of 1.5 tonnes and a lifting platewith aminimumdiameter of 80millimetres(3.1 inches).

172

Wheels and tyres

Vehicleswithout tyre repair kit

BD

A

E105575

C

JackA

B Wheel brace

Screw-in towing eyeC

Space for wheel trim removerD

Your vehicle jack, wheel brace, screw-intowing eye and wheel trim remover arelocated in the spare wheel well.

Jacking and lifting points

CAUTION

Use only the specified jacking points.If you use other positions, you maydamage the body, steering,

suspension, engine, braking system orthe fuel lines.

E92658

A

B

173

Wheels and tyres

Emergency use onlyA

MaintenanceB

E93184

A

Indentations in the sills A show thelocation of the jacking points.

E92932

E93020

Assembling thewheel brace

Type one

WARNING

When returning the wheel braceextension to its original position, takecare not to get your fingers caught.

Note:Make sure that the wheel brace isfully extended.

E122546

Extend the wheel brace.

Type two

CAUTION

The screw-in towing eye has aleft-hand thread. Turn itanti-clockwise to install it. Make sure

that the towing eye is fully tightened.

E122502

174

Wheels and tyres

Insert the screw-in towing eye into thewheel brace.

Removing thewheel trim

Type one

Insert the flat end of the wheel bracebetween the rim and the trim and carefullyremove the trim.

Type two

E122314

2

1

1. Insert the wheel trim remover.

2. Remove the trim.

Note:Make sure that you pull the wheeltrim remover at right angles to the trim.

Removing a roadwheel

WARNINGSPark your vehicle in such a positionthat neither the traffic nor you arehindered or endangered.

Set up a warning triangle.

WARNINGSMake sure that the vehicle is on firm,level ground with the wheelspointing straight ahead.

Switch off the ignition and apply theparking brake.

If your vehicle has a manualtransmission, select first or reversegear. If it has an automatic

transmission, select park.

Have the passengers leave thevehicle.

Secure the diagonally oppositewheel with an appropriate block orwheel chock.

Make sure that the arrows ondirectional tyres point in the directionof rotation when the vehicle is

moving forwards. If you have to fit a sparewheel with the arrows pointing in theopposite direction, have the tyre refittedin the correct direction by a properlytrained technician.

Do notwork underneath the vehiclewhen it is supported only by a jack.

Make sure that the jack is vertical tothe jacking point and the base is flaton the ground.

CAUTION

Donot lay alloywheels face downonthe ground, this will damage thepaint.

Note: The spare wheel is located underthe floor cover in the luggagecompartment.

175

Wheels and tyres

E121887

1

2

1. Install the locking wheel nut key.

2. Slacken the wheel nuts.

3. Jack up the vehicle until the tyre isclear of the ground.

4. Remove the wheel nuts and thewheel.

Installing a roadwheel

WARNINGSUse only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will make

the National Type Approval invalid. SeeTechnical specifications (page 181).

Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer

for more details regarding compatibility.

CAUTION

Do not install alloy wheels usingwheel nuts designed for use withsteel wheels.

Note:Make sure the wheel and hubcontact surfaces are free from foreignmatter.

Note:Make sure that the cones on thewheel nuts are against the wheel.

1. Install the wheel.

2. Install the wheel nuts finger tight.

3. Install the locking wheel nut key.

1

2

3 4

5

E75442

4. Partially tighten the wheel nuts in thesequence shown.

5. Lower the vehicle and remove thejack.

6. Fully tighten the wheel nuts in thesequence shown. See Technicalspecifications (page 181).

7. Install the wheel trim using the ball ofyour hand.

176

Wheels and tyres

WARNING

Have the wheel nuts checked fortightness and the tyre pressurechecked as soon as possible.

Note: If the sparewheel is different in sizeor construction to the road wheels, havethis replaced as soon as possible.

TYREREPAIRKIT

Your vehicle may not have a spare tyre.In this case it will have an emergency tyrerepair kit that can be used to repair oneflat tyre.

The tyre repair kit is located in the sparewheel well.

General information

WARNINGSDepending on the type and extentof tyre damage, some tyres canonly be partially sealed or not sealed

at all. Loss of tyre pressure can affectvehicle handling, leading to loss of vehiclecontrol.

Do not use the tyre repair kit if thetyre has already been damaged asa result of being driven under

inflated.

Do not try to seal damage otherthan that located within the visibletread of the tyre.

Do not try to seal damage to thetyre’s sidewall.

The tyre repair kit seals most tyrepunctures [with a diameter of up to sixmillimetres (1/4 inch)] to temporarilyrestore mobility.

Observe the following rules when usingthe kit:

• Drivewith caution and avoidmaking sudden steering ordrivingmanoeuvres, especially ifthe vehicle is heavily loaded or you aretowing a trailer.

• The kit will provide you with anemergency temporary repair, enablingyou to continue your journey to thenext vehicle or tyre dealer, or to drivea maximum distance of200 kilometres (125 miles).

• Do not exceed amaximumspeedof 80 km/h (50mph).

• Keep the kit out of the reach ofchildren.

• Only use the kit when the ambienttemperature is between –30°C (-22°F)and +70°C (+158°F).

Using the tyre repair kit

WARNINGSCompressed air can act as anexplosive or propellant.

Never leave the tyre repair kitunattended while in use.

CAUTION

Do not keep the compressoroperating for more than 10 minutes.

Note: Use the tyre repair kit only for thevehicle with which it was supplied.

• Park your vehicle at the roadside sothat you do not obstruct the flow oftraffic and so that you are able to usethe kit without being in danger.

• Apply the parking brake, even if youhave parked on a level road, to makesure that the vehicle will not move.

• Do not attempt to remove foreignobjects like nails or screwspenetratingthe tyre.

177

Wheels and tyres

• Leave the engine running while the kitis in use, but not if the vehicle is in anenclosed or poorly ventilated area (forexample, inside a building). In thesecircumstances, switch thecompressor onwith the engine turnedoff.

• Replace the sealant bottle with a newone before the expiry date (see topof bottle) is reached.

• Inform all other users of the vehiclethat the tyre has been temporarilysealed with the tyre repair kit andmake them aware of the specialdriving conditions to be observed.

Inflating the tyre

WARNINGSCheck the sidewall of the tyre priorto inflation. If there are any cracks,bumps or similar damage, do not

attempt to inflate the tyre.

Do not stand directly beside the tyrewhile the compressor is pumping.

Watch the sidewall of the tyre. If anycracks, bumps or similar damageappear, turn off the compressor and

let the air out by means of the pressurerelief valveB. Do not continue drivingwiththis tyre.

The sealant contains natural rubberlatex. Avoid contact with skin andclothing. If this happens, rinse the

affected areas immediately with plenty ofwater and contact your doctor.

If the tyre inflation pressure does notreach 1.8 bar (26 psi) within sevenminutes, the tyremay have suffered

excessive damage, making a temporaryrepair impossible. In this case, do notcontinue driving with this tyre.

CAUTION

Screwing the bottle onto the bottleholder will pierce the seal of thebottle. Do not unscrew the bottle

from the holder as the sealant will escape.

E94973

BJ

I

FE

C

KA

G

H

D

Protective capA

Pressure relief valveB

HoseC

Orange capD

Bottle holderE

Pressure gaugeF

178

Wheels and tyres

Power plug with cableG

Compressor switchH

LabelI

Bottle lidJ

Sealant bottleK

1. Open the lid of the tyre repair kit.

2. Peel off the label I showing themaximum permissible speed of80 km/h (50 mph) from the casingand attach it to the instrument panelin the driver’s field of view. Make surethe label does not obscure anythingimportant.

3. Take the hose C and the power plugwith cableG out of the kit.

4. Unscrew the orange cap D and thebottle lid J.

5. Screw the sealant bottle K clockwiseinto the bottle holder E fully tight.

6. Remove the valve cap from thedamaged tyre.

7. Detach the protective capA from thehose C and screw the hose C firmlyonto the valve of the damaged tyre.

8. Make sure that the compressor switchH is in position 0.

9. Insert the power plugG into the cigarlighter socket or auxiliary powersocket. SeeCigarlighter (page 103).See Auxiliary power sockets(page 104).


11. Move the compressor switch H toposition 1.

12. Inflate the tyre for no longer thanseven minutes to an inflationpressure ofminimum 1.8 bar (26 psi)and a maximum of 3.5 bar (51 psi).Move the compressor switch H toposition0 and check the current tyrepressure with pressure gauge F.

13. Remove the power plugG from thecigar lighter socket or auxiliary powersocket.

14. Quickly unscrew the hose C fromthe tyre valve and replace theprotective cap A. Fasten the valvecap again.

15. Leave the sealant bottle K in thebottle holder E.

16. Make sure the kit, the bottle lid andthe orange cap are stored safely, butstill easily accessible in the vehicle.The kit will be required again whenyou check the tyre pressure.

17. Immediately drive approximatelythree kilometres (two miles) so thatthe sealant can seal the damagedarea.

Note:When pumping in the sealantthrough the tyre valve, the pressure mayrise up to 6 bar (87 psi) but will drop againafter about 30 seconds.

WARNING

If you experience heavy vibrations,unsteady steering behaviour ornoises while driving, reduce your

speed and drive with caution to a placewhere it is safe for you to stop the vehicle.Recheck the tyre and its pressure. If thetyre pressure is less than 1.3 bar (19 psi)or if there are any cracks, bumps or similardamage visible, do not continue drivingwith this tyre.

Checking the tyre pressure

1. Stop the vehicle after drivingapproximately three kilometres(two miles). Check, and wherenecessary, adjust the pressure of thedamaged tyre.

2. Attach the kit and read the tyrepressure from the pressure gauge F.

179

Wheels and tyres

3. If the pressure of the sealant-filled tyreis 1.3 bar (19 psi) or more, adjust it tothe specified pressure. SeeTechnical specifications (page181).

4. Follow the inflation procedure onceagain to top up the tyre.

5. Check the tyre pressure again fromthe pressure gauge F. If the tyrepressure is too high, deflate the tyreto the specified pressure using thepressure relief valve B.

6. Once you have inflated the tyre to itscorrect tyre pressure, move thecompressor switch H to position 0,remove the power plugG from thesocket, unscrew the hose C, fastenthe valve cap and replace theprotective cap A.

7. Leave the sealant bottleK in the bottleholder E and store the kit away safelyin its original location.

8. Drive to the nearest tyre specialist toget the damaged tyre replaced.Before the tyre is removed from therim, inform your tyre dealer that thetyre contains sealant. Renew the kitas soon as possible after it has beenused once.

Note: Remember that emergencyroadside tyre repair kits only providetemporary mobility. Regulationsconcerning tyre repair after usage of tyrerepair kit may differ from country tocountry. You should consult a tyrespecialist for advice.

WARNING

Before driving, make sure the tyreis adjusted to the recommendedinflation pressure. See Technical

specifications (page 181). Monitor thetyre pressure until the sealed tyre isreplaced.

Empty sealant bottles can be disposedof togetherwith normal householdwaste.Return remains of sealant to your dealeror dispose of it in compliance with localwaste disposal regulations.

TYRECARE

E70415

To make sure the front and rear tyres ofyour vehicle wear evenly and last longer,we recommend that you swap the tyresfrom front to rear and vice versa at regularintervals of between 5 000 and 10 000km (3 000 and 6 000 miles).

CAUTION

Do not scrub the sidewalls of thetyres when you are parking.

If you have to mount a kerb, do so slowlyand approach it with the wheels atright-angles to the kerb.

Examine the tyres regularly for cuts,foreign objects and uneven wear of thetread. Uneven wear could mean that thewheel alignment is outside specification.

Check the tyre pressures (including thespare) when cold, every two weeks.

180

Wheels and tyres

USINGWINTER TYRES

CAUTION

Make sure that you use the correctwheel nuts for the type of wheel thewinter tyres are fitted to.

If winter tyres are used, make sure thatthe tyre pressures are correct. SeeTechnical specifications (page 181).

USINGSNOWCHAINS

WARNINGSDo not exceed 50 km/h (30 mph).

Do not use snow chains onsnow-free roads.

Only fit snow chains to specifiedtyres. See Technicalspecifications (page 181).

CAUTION

If your vehicle is fitted with wheeltrims, remove them before fittingsnow chains.

Note: The ABS will continue to operatenormally.

Only use small link snow chains.

Only use snowchains on the frontwheels.

Vehicleswith stability control(ESP)

Vehicles with stability control (ESP) mayexhibit some unusual drivingcharacteristics which can be avoided byswitching the system off. See Usingstability control (page 126).


Wheel nut torque

Nm (Ib-ft)Wheel type

130 (96)All

Tyre pressures (cold tyres)

Up to 80 km/h (50mph)

Full loadNormal load

Tyre sizeVariant RearFrontRearFront

bar (psi)bar (psi)bar (psi)bar (psi)

4.2 (61)4.2 (61)4.2 (61)4.2 (61)T125/85 R 16All

181

Wheels and tyres

Up to 160 km/h (100mph)




2.8 (41)2.4 (35)2.3 (33)2.1 (31)195/65 R 15*All

2.8 (41)2.4 (35)2.3 (33)2.3 (33)225/40 R 18All

2.8 (41)2.4 (35)2.3 (33)2.1 (31)205/55 R 16*Vehicles with apetrol engine

2.8 (41)2.4 (35)2.3 (33)2.3 (33)205/55 R 16*Vehicles with adiesel engine

2.8 (41)2.4 (35)2.3 (33)2.1 (31)205/50 R 17Vehicles with apetrol engine

2.8 (41)2.4 (35)2.3 (33)2.3 (33)205/50 R 17Vehicles with adiesel engine

*Only fit snow chains to specified tyres.

Continuous speed in excess of 160 km/h (100mph)




3.0 (44)2.6 (38)2.3 (33)2.3 (33)195/65 R 15All

3.0 (44)2.6 (38)2.3 (33)2.5 (36)225/40 R 18All





182

Wheels and tyres

VEHICLE IDENTIFICATIONPLATE

E85610C

B

E D

A

Vehicle identification numberA

Gross vehicle weightB

Gross train weightC

Maximum front axle weightD

Maximum rear axle weightE

The vehicle identification number andmaximum weights are shown on a platelocated on the lock side of the passengerdoor aperture at the bottom.

VEHICLE IDENTIFICATIONNUMBER (VIN)

E87496

The vehicle identification number isstamped into the floor panel on theright-hand side, beside the front seat. It isalso shown on the left-hand side of theinstrument panel.

183

Vehicle identification


Vehicle dimensions

E78157

Dimension inmm(inches)

Dimension descriptionItem

4 372 - 4 391 (170.6 -172.9)Maximum lengthA

2 022 - 2 023 (79.6 -79.7)Overall width including exterior mirrorsB

1 564 - 1 596 (61.6 -62.8)Overall height - EC kerb weightC

2 640 (103.9)WheelbaseD

184

Technical specifications



1 535 - 1 606 (60.4 -63.2)Front trackE

1 531 - 1 607 (60.3 -63.3)Rear trackE

Towing equipment dimensions

E78158



103 (4.1)Bumper – end of tow ball - fixed tow ballA

146 (5.7)Bumper – end of tow ball - detachable tow ballA

32 (1.3)Attachment point – centre of tow ballB

185




898 (35.4)Wheel centre – centre of tow ball - fixed tow ballC

941 (37.0)Wheel centre – centre of tow ball - detachable towball

C

517 (20.4)Centre of tow ball – side memberD

1 034 (40.7)Distance between side membersE

400 (15.7)Centre of tow ball – centre 1. attachment point -fixed tow ball

F

443 (17.4)Centre of tow ball – centre 1. attachment point -detachable tow ball

F

699 (27.5)Centre of tow ball – centre 2. attachment point -fixed tow ball

G

742 (29.2)Centre of tow ball – centre 2. attachment point -detachable tow ball

G

186


GENERAL INFORMATION

CAUTION

Using the systemwith the engine offwill drain the battery.

This section describes the functions andfeatures of the Bluetooth mobile phonehands free system.

The Bluetooth mobile phone part of thesystemprovides interactionwith the audioor navigation system and your mobilephone. It allows you to use the audio ornavigation system to make and receivecalls without having to use your mobilephone.

Compatibility of phones

CAUTION

As no common agreement exists,mobile phonemanufacturers are ableto implement a variety of profiles in

their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insomecasesmay significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.

Please visit the websitewww.ford-mobile-connectivity.com for fulldetails.

TELEPHONESETUP

Phonebook

After start up access to the phonebooklist can be delayed for several minutes,depending upon the size.

Phonebook categories

Depending on your phonebook entry,different categories can be displayed inthe audio unit.

For example:

MobileM

OfficeO

HomeH

FaxF

Note: Entries may be displayed withouta category attachment.

The category can also be indicated as anicon:

E87990

Phone

E87991

Mobile

E87992

Home

E87993

Office

E87994

Fax

Making a phone an activephone

When using the system for the first time,no phone is connected to the system.

Bluetooth phone

After bonding a Bluetooth phone to thesystem, this becomes the active phone.For further information refer to the phonemenu.

187

Telephone

Select the phone from the active phonemenu.

Turning the ignition and radio or navigationunit back on again, the last active phoneis picked up by the system.

Note: In some cases the Bluetoothconnection must also be confirmed onthe phone.

BondanotherBluetoothphone

Bond a new Bluetooth phone asdescribed in the requirements for aBluetooth connection.

Phones stored in the system areaccessible by using the phone list on theaudio unit.

Note: Amaximumof six devicesmay bebonded. If six Bluetooth devices havealready been bonded, one of these hasto be debonded in order to bond a newdevice.

BLUETOOTHSETUP

Before you can use your telephone withyour vehicle it must be bonded to thevehicle telephone system.

Handling of phones

Up to six Bluetooth devices can bebonded to the vehicle system.

Note: If there is an ongoing call when thephone in use is selected as the newactivephone, the call is transferred to the vehicleaudio system.

Note: Even if connected to the carsystem, your phone can still be used inthe usual way.

Requirements for Bluetoothconnection

The following are required before aBluetooth phone connection can bemade.

1. The Bluetooth feature must beactivated on the phone and on theaudio unit. Make sure the Bluetoothmenu option in the audio unit is set toON. For information on phonesettings, refer to your phone userguide.

2. The private mode must not beactivated on the Bluetooth phone.

3. Search for audio device.4. Select Ford Audio.5. Enter the code number shown on the

vehicle display using the phonekeypad. If no code number is shownon the display, enter the Bluetooth PINnumber 0000 using the phonekeypad. Now enter the Bluetooth PINnumber shown on the vehicle display.

Note: A phone call will be disconnectedif the audio unit is switched off. If theignition key is turned to the off positionthe phone call will remain in progress.

188

Telephone

TELEPHONECONTROLS

Remote control

Voice andmodebutton

2

1

E87661

Voice button1

Mode button2

Incoming calls can be accepted bypressing the MODE button once. Pressthe button again to end the call.

USINGTHE TELEPHONE -VEHICLESWITHOUT:NAVIGATIONSYSTEM

This chapter describes the phonefunctions of the audio unit.

Note: Refer to your audio guide fordetails of the controls.

An active phone must be present.

Even if connected to the audio unit, yourphone can still be used in the usual way.

Note: You can exit the phone menu bypressing any source buttonCD,AM/FMor AUX.

Making a call

Dialling a number using voicecontrol

Phonenumbers canbedialled using voicecontrol. See Telephone commands(page 206).

Diallinganumberusingtheaddressbook

You can access your phone addressbook via Bluetooth. The entrieswill appearin the unit display.

1. Press the PHONE or the call acceptbutton.

2. Press theMENU button.

3. Keep pressing theMENUbutton untilPHONEBOOK appears.

4. Press the seek buttons to select thedesired phone number.

Note: Press and hold the seek button toskip to the next letter in the alphabet.

5. Press the PHONE or the call acceptbutton to dial the selected phonenumber.

Diallinganumberusingtheaddressbook - Sony radio

You can access your phone addressbook via Bluetooth. The entrieswill appearin the unit display.

1. Press the PHONE button.

2. Press the seek button until the phonebook is shown.

3. Press the up/down arrow buttons toselect the desired phone number.

Note:Press and hold the up/downarrowbuttons to skip to the next letter in thealphabet.

4. Press the PHONE or the call acceptbutton to dial the selected phonenumber.

189

Telephone

Dialling a number using thetelephone keypad

If you have an audio unit with a telephonekeypad (buttons 0-9, * and #):

1. Press the call accept button. PressthePHONEbutton if you have a Sonyradio.

2. Dial the number using the telephonekeypad on the audio unit.

3. Press the call accept button.

Note: If you enter an incorrect digit whilstentering a phone number, press the seekleft button to erase the last digit. A longpress will erase the complete string ofdigits.

Press and hold 0 to enter a + digit.

Ending a call

Calls can be ended by pressing the callreject button.

Audio units without a telephone keypadcan also end a call by pressing eitherPHONE, CD, AM/FM orON/OFF, orby pressing theMODE button on theremote control

Redialling a number


2. Press theMENU button.

3. Select the CALLOUT list or theCALL IN list. On some audio units,select theMISSED, INCOMING orOUTGOING calls list.

Note: If the active phone does notprovide a call out list, the last outgoing callnumber/entry can be redialled.

4. Press the seek button on the audiounit.

5. Press the PHONE or the call acceptbutton to dial the desired phonenumber.

Redialling a number - Sony radio


2. Press the seek button until the desiredlist is displayed.

Note: If the active phone does notprovide a call out list, the last outgoing callnumber/entry can be redialled.

3. Press the up/down buttons to selectthe desired phone number.

4. Press the PHONE or the call acceptbutton to dial the phone number.

Redialling the last dialled number -Sony radio

1. Press the call accept button.

2. Press the call accept button a secondtime to dial the number.

Receiving an incoming call

Accepting an incoming call

Incoming calls can be accepted bypressing either the call accept button, thePHONE button or theMODE button onthe remote control.

Rejecting an incoming call

Incoming calls can be rejected bypressing the call reject button.

Audio units without a telephone keypadcan also reject a call by pressing eitherPHONE, CD, AM/FM orON/OFF.

Receiving a second incomingcall

Note: The second incoming call functionmust be activated in your phone.

If there is an incoming call whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.

190

Telephone

Accepting a second incoming call

Second incoming calls can be acceptedby pressing either the call accept button,thePHONEbutton, or theMODEbuttonon the remote control.

Rejecting a second incoming call

Second incoming calls can be rejected bypressing the call reject button. Unitswithout a telephone keypad can alsoreject a second incoming call by pressingthe CD button, or the AM/FM button.

Muting themicrophone

During a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.

Audio unitswith green call acceptbutton

Press the call accept button. Press thebutton once again to turn this function off.

Audio unitswithout green callaccept button

Press the seek up or down button. Pressthe button once again to turn this functionoff.

Changing the active phone

Note: Phones must be bonded to thesystem before they can be made active.

Using the station storage button

Note: This process is only for audio unitswithout a telephone keypad.

1. Press the PHONE button on theaudio unit.

2. Press the preset number required(using the station preset buttons 1 -6).

Using the audio unitmenu

Note: After bonding a phone to thesystem, this becomes the active phone.

1. Press the PHONE or call acceptbutton.

2. Press theMENU button on the audiounit.

3. Select the ACTIVEPHONE optionon the audio unit.

4. Scroll through the different storedphones by using the seek buttons todisplay the bonded phones.

5. Press theMENU button to select thephonewhich is to be the active phone.

Debonding a bonded phone

Abondedphone canbedeleted from thesystem at any time, unless a phone call isin progress.

1. Press the PHONE or call acceptbutton.

2. Press theMENU button on the audiounit.

3. Select the DEBOND option on theaudio unit.

4. Scroll through the different phones byusing the seek buttons anddisplay thephone to be debonded.

5. Press theMENU button to select thephone which is to be debonded.

Debonding a bonded phone -Sony radio


1. Press the PHONE button.

2. Press the up/downarrowbuttons untilyou reach the DEBOND option.

191

Telephone

3. Scroll through the different phones byusing the seek buttons anddisplay thephone to be debonded.

4. Press the OK button to be debond.

USINGTHE TELEPHONE -VEHICLESWITH:NAVIGATIONSYSTEM

This chapter describes the phonefunctions of the Navigation System.

Note: Refer to your Navigation Systemguide for details of the controls.

An active phone must be present.

Even if connected to the NavigationSystem, your phone can still be used inthe usual way.

Making a call

Dialling a number

Phonenumbers canbedialled using voicecontrol. See Voice control (page 194).

Ending a call

Calls can be ended by pressing either theEND button, theMODE button on theremote switch or theON/OFF button onthe navigation system.

Redialling a number

1. Press thePHONE button on the unit.2. Select REDIAL.

Receiving an incoming call

Accepting an incoming call

Incoming calls can be accepted bypressing either the call accept button, theMODEbutton on the remote control, thePHONE button on the unit or by usingthe ACCEPT option in the menu.

Rejecting an incoming call

Incoming calls can be rejected bypressing either the call reject button, theCD orAM/FM buttons on the unit, or byusing the REJECT option in the menu.

Receiving a second incomingcall

Note: The second incoming call functionmust be activated in your phone.

If there is an incoming call, whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.

Accepting a second incoming call

Second incoming calls can be acceptedby pressing either the call accept button,theMODEbutton on the remote control,the PHONE button on the unit or byusing the ACCEPT option in the menu.

Note: This will cancel the ongoing call.

Rejecting a second incoming call

Second incoming calls can be rejected bypressing either the call reject button, orone of the following buttons on the unit:CD, AM/FM.

Muting themicrophone

During a call, it is possible to mute themicrophone. Whilst muted, confirmationwill appear in the display.

DVDnavigation units

Press the mute button (symbol of amicrophone with a line through it). Pressthe button once again to turn this functionoff.

192

Telephone

CDnavigation units

Press themicrophonemutebutton. Pressthe button once again to turn this functionoff.

Changing the active phone

Note: Phones must be bonded to thesystem before they can be made active.

Note: After bonding a phone to thesystem, this becomes the active phone.

1. Press thePHONE button on the unit.2. Using the BTSETTINGS option in

the menu, select the active phonefrom the list.

Debonding a bonded phone


1. Press thePHONE button on the unit.2. Select the BTSETTINGS option in

the menu.

3. Select the DEBOND option in themenu.

4. Select the phone from the list.

193

Telephone


CAUTION


Voice recognition enables operation ofthe systemwithout the need to divert yourattention from the road ahead in order tochange settings, or receive feedbackfrom the system.

Whenever you issue one of the definedcommands with the system active, thevoice recognition system converts yourcommand into a control signal for thesystem. Your inputs take the form ofdialogues or commands. You are guidedthrough these dialogues byannouncements or questions.

Please familiarise yourself with thefunctions of the systembefore using voicerecognition.

Supported commands

The voice control system allows you tocontrol the following vehicle functions:

• Bluetooth phone

• radio

• CD Player/CD Changer

• external device (USB)

• external device (iPod)

• automatic climate control

• navigation system (DVD units only -refer to separate DVD navigationhandbook).

System response

As you work through a voice session thesystem will prompt you with a beep toneeach time the system is ready to proceed.

Do not try to give any commands until thebeep tone has been heard. The voicecontrol system will repeat each spokencommand back to you.

If you are not sure how to continue say"HELP" for assistance or "CANCEL" if youdo not wish to continue.

The "HELP" function provides only asubset of the available voice commands.Detailed explanations of all possible voicecommands can be found on the followingpages.

Voice commands

All voice commands should begivenusinga natural speaking voice, as if speaking toa passenger or on the phone. Your voicelevel should be dependant on thesurrounding noise level inside or outsidethe vehicle but do not shout.

USINGVOICECONTROL

Systemoperation

The order and content of the voicecontrols are given in the following lists. Thetables show the sequence of user voicecommands and system responses foreach available function.

<> indicates a number or stored name tagto be inserted by the user.

Short cuts

There are a number of voice commandshort cuts available, which allow you tocontrol some vehicle features withouthaving to follow the complete commandmenu. These are:

• phone: "MOBILE NAME", "DIALNUMBER", "DIAL NAME", and"REDIAL"

• CD player/CD changer: "DISC" and"TRACK"

194

Voice control

• automatic climate control:"TEMPERATURE", "AUTO MODE","DEFROSTING/DEMISTING ON" and"DEFROSTING/DEMISTING OFF"

• radio: "TUNE NAME"

• external device (USB): "TRACK"

• external device (iPod): "TRACK"

• SD card: "TRACK".

Start communicatingwith thesystem

Before you can start talking to the systemyou first have to press the VOICE orMODE button for each operation andwait until the systemanswerswith a beep.See Voice control (page 42).

Press the button again to cancel the voicesession.

Name tag

The name tag functionality can supportthe phone, audio and navigation featuresby using the "STORENAME" function. Youcan assign name tags to items such asfavourite radio stations and personalphone contacts. See Audio unitcommands (page195). SeeTelephonecommands (page 206). SeeNavigation systemcommands(page 210).

• Store up to 20name tags per function.

• The average recording time for eachname tag is approximately 2-3seconds.

AUDIOUNITCOMMANDS

CDPlayer

You can control playback directly by voicecontrol.

Overview

The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.

"CDPLAYER"

"HELP"

"PLAY"

"TRACK"*

"SHUFFLE ALL"

"SHUFFLE FOLDER"**

"SHUFFLE OFF"

"REPEAT FOLDER"**

195

Voice control

"CDPLAYER"

"REPEAT TRACK"

"REPEAT OFF"

* Can be used as a shortcut.

** Only available if the CD contains audio data files like MP3 or WMA.

Track

You can choose a track on your CDdirectly.

SystemanswerUser saysSteps

"CD PLAYER""CD PLAYER"1

"TRACK NUMBER PLEASE""TRACK"*2

"TRACK <number>""<a number between 1 and 99>"**3


** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)

Shuffle all

To set random playback.


"CD PLAYER""CD PLAYER"1

"SHUFFLE ALL"2

CDChanger

Overview


196

Voice control

"CDCHANGER"

"HELP"

"PLAY"

"DISC"*

"TRACK"*

"SHUFFLE ALL"

"SHUFFLE CD"

"SHUFFLE FOLDER"**

"SHUFFLE OFF"

"REPEAT CD"

"REPEAT FOLDER"**

"REPEAT TRACK"

"REPEAT OFF"


** Only available if the CD contains audio data files like MP3 or WMA.

Disc

If you have aCDchanger you can choosethe disc number.


"CD CHANGER""CD CHANGER"1

"DISC NUMBER PLEASE""DISC"*2

"DISC <number>""<a number between 1 and 6>"3


Track

You can choose a track on your CDdirectly.

197

Voice control






** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)

Shuffle CD

To set random playback within the CDcontents.



"SHUFFLE CD"2

Radio

The radio voice commands support thefunctionality of the radio and allow you totune radio stations by voice control.

Overview

The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu.

"RADIO"

"HELP"

"AM"

"FM"

"TUNE NAME"*

"DELETE NAME"

"DELETE DIRECTORY"

"PLAY DIRECTORY"

"STORE NAME"

198

Voice control

"RADIO"

"PLAY"


Tune frequency

This function allows you to tune your radioby voice commands.


"RADIO""RADIO"1

"AM FREQUENCY PLEASE""AM"2

"FM FREQUENCY PLEASE""FM"

"TUNE <frequency>""<frequency>"*3

* The frequency may be entered in a variety of ways. Refer below for representativeexamples.

FMband: 87.5 - 108.0 in increments of 0.1

• "Eighty nine point nine" (89.9)

• "Ninety" (90.0)

• "One hundred point five" (100.5)

• "One zero one point one" (101.1)

• "One zero eight" (108.0)

AM/MW band: 531 - 1602 in incrementsof 9

AM/LW band: 153 - 281 in increments of1

• "Five thirty one" (531)

• "Nine hundred" (900)

• "Fourteen forty" (1440)

• "Fifteen zero three" (1503)

• "Ten eighty" (1080)

Store name

If you have tuned a radio station, you canstore it with a name in the directory.


"RADIO""RADIO"1

"STORE NAME""STORE NAME"2"NAME PLEASE"

"REPEAT NAME PLEASE""<name>"3

"STORING NAME""<name>"4"<name> STORED"

199

Voice control

Tune name

This function allows you to call up a storedradio station.


"RADIO""RADIO"1

"NAME PLEASE""TUNE NAME"*2

"TUNE <name>""<name>"3


Delete name

This function allows you to delete a storedradio station.


"RADIO""RADIO"1

"NAME PLEASE""DELETE NAME"2

"DELETE <name>""<name>"3"CONFIRM YES OR NO"

"DELETED""YES"4

"COMMAND CANCELLED""NO"

Play directory

This function allows you to let the systemtell you all of the stored radio stations.


"RADIO""RADIO"1

"PLAY <DIRECTORY>""PLAY DIRECTORY"2

Delete directory

This function allows you to delete allstored radio stations at once.

200

Voice control


"RADIO""RADIO"1

"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"

"RADIO DIRECTORY DELETED""YES"3


Play

This function switches the audio sourceto the radio mode.


"RADIO""RADIO"1

"PLAY"2

Auxiliary input

This function allows you to switch theaudio source to the attached auxiliaryinput device.


"EXTERNAL DEVICE""EXTERNAL DEVICE"1

"LINE IN""LINE IN"2

External devices - USB

These voice commands support thefunctionality of an external USB devicewhich may be connected to the audiounit.

Overview


"EXTERNALDEVICE", "USB"

"HELP"

201

Voice control

"EXTERNALDEVICE", "USB"

"PLAY"

"TRACK"*

"PLAYLIST"**

"FOLDER"**

"SHUFFLE ALL"

"SHUFFLE FOLDER"

"SHUFFLE PLAYLIST"

"SHUFFLE OFF"

"REPEAT TRACK"

"REPEAT FOLDER"

"REPEAT OFF"


** Playlists and folders activated by voice control must be assigned special filenames.SeeGeneral information (page 213).

USBplay

This function allows you to switch theaudio source to the attachedUSBdevice.



"USB""USB"2

"PLAY"3

USBTrack

You can choose a track on your USBdevice directly.

202

Voice control



"USB""USB"2

"TRACK NUMBER PLEASE""TRACK"3

"TRACK <number>""<a number between 1 and 99>"*4

* Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)

External devices - iPod

These voice commands support thefunctionality of an iPod which may beconnected to the audio unit.

Overview


"EXTERNALDEVICE", "IPOD"

"HELP"

"PLAY"

"TRACK"*

"PLAYLIST"**

"SHUFFLE ALL"

"SHUFFLE PLAYLIST"

"SHUFFLE OFF"

"REPEAT TRACK"

"REPEAT OFF"


** Playlists activated by voice controlmust be assigned special filenames. SeeGeneralinformation (page 213).

203

Voice control

iPod Track You can choose a track off the all titles listof your iPod directly.



"IPOD""IPOD"2




** Additionally, numbers can be spoken as up to five single digits (for example "5", "2","4", "5", "3" for track 52453), to a limit of 65535.

iPod playlist

You can choose a playlist from your iPoddirectly.



"IPOD""IPOD"2

"PLAYLIST NUMBER PLEASE""PLAYLIST"*3

"PLAYLIST <number>""<a number between 1 and 10>"4

* Playlists activated by voice controlmust be assigned special filenames. SeeGeneralinformation (page 213).

SDCard

These voice commands support thefunctionality of an SD card which hassuitable audio files written to it.

Overview


"SDCARD"

"HELP"

204

Voice control

"SDCARD"

"PLAY"

"TRACK"*

"SHUFFLE ALL"

"SHUFFLE FOLDER"

"SHUFFLE OFF"

"REPEAT TRACK"

"REPEAT FOLDER"

"REPEAT OFF"


SDcard play

This function allows you to switch theaudio source to the SD card audio files.


"SD CARD""SD CARD"1

"PLAY"2

SDcard track

You can choose a track on your SD carddirectly.


"SD CARD""SD CARD"1




** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245).

205

Voice control

TELEPHONECOMMANDS

Phone

Your phone system allows you to createan additional phonebook. The storedentries can be dialled by voice control.Phone numbers stored by using voicecontrol are stored on the vehicle systemand not in your phone.

Overview


"PHONE"

"HELP"

"MOBILE NAME"*

"DIAL NUMBER"*

"DIAL NAME"*

"DELETE NAME"

"DELETE DIRECTORY"

"PLAY DIRECTORY"

"STORE NAME"

"REDIAL"*

"ACCEPT CALLS"

"REJECT CALLS"


Phone functions

Dial number

Phone numbers can bedialled after givingthe name tag voice command.


"PHONE""PHONE"1

206

Voice control


"NUMBER PLEASE""DIAL NUMBER"*2

"<phone number>"<phone number>"3CONTINUE?"

"DIALLING""DIAL"4

"<repeat last part of number>"CORRECTION"CONTINUE?"


Dial name

Phone numbers can bedialled after givingthe name tag voice command.


"PHONE""PHONE"1

"NAME PLEASE""DIAL NAME"*2

"DIAL <name>""<name>"3"CONFIRM YES OR NO"

"DIALLING""YES"4



Redial

This function allows you to redial the lastdialled phone number.


"PHONE""PHONE"1

"REDIAL""REDIAL"*2"CONFIRM YES OR NO"

"DIALLING""YES"3

207

Voice control




Mobile name

This function allows you to access phonenumbers stored with a name tag in yourmobile phone.


"PHONE""PHONE"1

"MOBILE NAME" "<phonedependent dialogue>"

"MOBILE NAME"*2


DTMF (Tone dialling)

This function transfers spoken numbersinto DTMF tones. For example, to makea remote enquiry to your homeansweringmachine or to enter a PIN number etc.

Note: DTMF can only be used during anongoing call. Press the VOICE button andwait for the system prompt.

Can only be used with vehicles installedwith a dedicated VOICE button.


"NUMBER PLEASE"1

"<numbers 1 to 9, zero, hash, star>"2

Create a phonebook

Store name

New entries can be stored with the"STORE NAME" command. This featurecan be used to dial a number by callingup the name instead of the full phonenumber.


"PHONE""PHONE"1

208

Voice control


"STORE NAME""STORE NAME"2"NAME PLEASE"

"REPEAT NAME PLEASE""<name>"3

"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"

"<phone number>""<phone number>"5

"STORING NUMBER""STORE"6"<phone number>""NUMBER STORED"

Delete name

Stored names can also be deleted fromthe directory.


"PHONE""PHONE"1

"NAME PLEASE""DELETE NAME"2

"DELETE <name>""<name>"3"CONFIRM YES OR NO"

"<name> DELETED""YES"4


Play directory

Use this function to let the system tell youall stored entries.


"PHONE""PHONE"1

"PLAY DIRECTORY""PLAY DIRECTORY"2

209

Voice control

Delete directory This function allows you to delete allentries in one go.


"PHONE""PHONE"1

"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"

"DIRECTORY DELETED""YES"3


Main settings

Reject calls

Calls can be set to be automaticallyrejected using voice control.


"PHONE""PHONE"1

"REJECT CALLS""REJECT CALLS"2

"ACCEPT CALLS""ACCEPT CALLS"*

* use this command to turn the reject mode off

NAVIGATIONSYSTEMCOMMANDS

Please refer to your separate Navigationhandbook for details of the commandmenus.

CLIMATECONTROLCOMMANDS

Climate

The climate voice commands supportsthe functionality of the fan speed,temperature and mode settings. Not allfunctions are available on all vehicles.

210

Voice control

Overview The overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.

"CLIMATE"

"HELP"

"FAN"*

"DEFROSTING/DEMISTING ON"*

"DEFROSTING/DEMISTING OFF"*

"TEMPERATURE"*

"AUTO MODE"*

* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.

Fan

This function allows you to adjust the fanspeed.


"CLIMATE""CLIMATE"1

"FAN SPEED PLEASE""‘FAN"*2

"FAN MINIMUM""MINIMUM"

3 "FAN <number>""<a number between 1 and 7>"

"FAN MAXIMUM""MAXIMUM"

* Can be used as a shortcut. On vehicles fitted with an English language module the"FAN" shortcut is not available.

211

Voice control

Defrosting/Demisting


"CLIMATE""CLIMATE"1

"DEFROSTINGON/DEMISTINGON""DEFROSTING ON/DEMISTING

ON"*2

"DEFROSTING OFF/DEMISTINGOFF"

"DEFROSTING OFF/DEMISTING

OFF"*


Temperature

This function allows you to adjust thetemperature.


"CLIMATE""CLIMATE"1

"TEMPERATURE PLEASE""TEMPERATURE"*2

"TEMPERATURE MINIMUM""MINIMUM"

3 "TEMPERATURE <number>""<a number between 15 and 29 °C

with 0.5 increments>" or "<anumber between 59 and 84 °F>"

"TEMPERATURE MAXIMUM""MAXIMUM"


Automode


"CLIMATE""CLIMATE"1

"AUTO MODE""AUTO MODE"*2

* Can be used as a shortcut. Can be deactivated by selecting a different temperatureor fan speed.

212

Voice control

GENERAL INFORMATION

CAUTIONSTake care when handling externaldevices with exposed electricalconnectors (such as the USB plug).

Always replace the protective cap/shieldwhen possible. There may be a risk ofelectrostatic discharge causing damageto the device.

Do not touch or handle the USBsocket in the vehicle. Cover thesocket when not in use.

Only use USB Mass-Storage devicecompliant devices.

Always switch your audio unit to adifferent source (for example theradio) before unplugging the USB

device.

Do not install or connect USB hubsor splitters.

Note: The system is only designed torecognize and read suitable audio filesfrom a USB device that conforms to theUSB Mass-Storage device class or aniPod. Not all available USBdevices can beguaranteed to function with the system.

Note: It is possible to connect compatibledevices with a trailing USB lead as well asthose that plug into the vehicle USBsocket directly (for exampleUSBmemorysticks and pen drives).

Note: Some USB devices with a higherpower consumption may not becompatible (for example some larger harddrives).

Note: Access time to read the files onthe external device will vary dependingupon factors such as the file structure,size and device content.

The system supports a range of externaldevices, to fully integrate with your audiounit via the USB and auxiliary inputsockets. Once connected, control of theexternal device is possible via the audiounit.

A list of typical compatible devices areshown below:• USB memory sticks

• USB portable hard drives

• MP3 players with USB connection

• iPod media players (refer towww.ford-mobile-connectivity.com for latestcompatibility list).

The system is USB 2.0 full speedcompatible, USB 1.1 host compliant andsupports FAT 16/32 file systems.

Information on audio filestructuresforexternaldevices

USB

Create only a single partition on the USBdevice.

If playlists are created, they must containcorrect file paths referenced to the USBdevice. It is recommended to create theplaylist after the audio files have beentransferred to the USB device.

Playlists must be created in .m3u format.

Audio files must be in .mp3 format.

Do not exceed the following limits:• 1000 items per folder (files, folders and

playlists)• 5000 folders per USB device

(including playlists)• 8 subfolder levels.

213

Connectivity

To enable voice control for customplaylists and folders, follow the procedurebelow:• Create folders named with the

structure "Ford<*>" where <*> is anumber 1-10. For example "Ford3"without an extension.

• Create playlists named with thestructure "Ford<*>.m3u"where <*>is a number 1-10. For example"Ford5.m3u" without any spacebetween "Ford" and the number.

Thereafter, custom folders and playlistswill be selectable with voice control. SeeAudio unit commands (page 195).

iPod

To enable voice control for customplaylists, create playlists named with thestructure "Ford<*>"where <*> is anumber 1-10. For example "Ford7"without any space between "Ford" andthe number.

Thereafter, playlists will be selectable withvoice control. See Audio unitcommands (page 195).

CONNECTINGANEXTERNALDEVICE

WARNING

Make sure the external device issecurelymountedwithin the vehicle,and that trailing connections do not

obstruct any of the driving controls.

External devicesmaybe connected usingthe auxiliary input socket and the USBport. See Auxiliary input (AUX IN)socket (page 109). SeeUSBport (page110).

Connection

Plug in the device, and if necessarysecure it to preventmovement within thevehicle.

Connecting an iPod

For optimum convenience and audioquality,we recommend that youpurchasea dedicated single connection leadavailable from your dealer.

Alternatively, it is possible to connect youriPod using the standard iPod USB cableand a separate 3.5mm audio jack lead. Ifusing thismethod preset the iPod volumeto maximum and turn off any equalizersettings before making the connections:

• Connect the headphoneoutput of theiPod to the AUX IN socket.

• Connect the USB cable from the iPodto the vehicle USB socket.

CONNECTINGANEXTERNALDEVICE - VEHICLESWITH:BLUETOOTH

Connecting aBluetooth audiodevice

CAUTION

As various standards exist,manufacturers are able to implementa variety of profiles in their Bluetooth

devices. Because of this, anincompatibility can occur between theBluetooth device and the system, whichin some cases may limit systemfunctionality. To avoid this situation, onlyrecommended devices should be used.

Please visit the websitewww.ford-mobile-connectivity.comfor full details.

214

Connectivity

Bonding the device

Note: Some audio and navigation unitshave a separate Bluetooth audio menu.Use this to access setup and control.

To connect the device to the systemfollow the same procedure as forBluetooth hands free phones. SeeBluetooth setup (page 188).

Operating the device

Select Bluetooth audio as the activesource.

Tracks can be accessed by skippingforwards and backwards using thesteering wheel controls, or directly fromthe audio unit controls.

USINGAUSBDEVICE

Various icons are used to identify typesof audio file, folders etc.

E100029

USB device is the active source

E100022

Folder

E100023

Playlist

E100024

Album

E100025

Artist

E100026

Filename

E100027

Track title

E100028

Information not available

Sony radio

Operation

Select the USB device as the audiosource by repeatedly pressing theCD/AUX button until USB appears in thedisplay. After first connecting the USBdevice, the first track within the first folderwill start to play automatically.Subsequently, following audio sourceswitching, the position of playback on theUSB device is remembered.

To browse the device contents, press theup/down arrow key or the OK buttononce.

The display will show the trackinformation, togetherwith other importantinformation described below:• A vertical scroll bar on the right side of

the display shows the current positionof the folder view.

• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).

• "<" before the list indicates that afurther level up is readable.

• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.

To navigate theUSBdevice contents, usethe up/down arrow keys to scroll throughlists, and the left/right keys to move up ordown within the folder hierarchy. Onceyour desired track, playlist or folder ishighlighted, press theOKbutton to selectplayback.

215

Connectivity

Note: If you wish to jump to the top levelof the USB device contents, press andhold the left arrow key.

Audio control

Press the left and right arrow keys to skipbackwards and forwards through tracks.

Press and hold the left/right arrow keysto enable fast rewind/fast forward throughtrack content.

Press the up/down arrow key or the OKbutton to browse the device contents.

Press the MENU key to enter the USBmenu. It is possible to enable shuffle andrepeat functions here with respect tofolders and playlists.

Press the SCANbutton to scan thewholedevice, current folder or a playlist if it is inoperation.

Press the INFO button to display thefollowing:• filename

• title

• artist

• album

• track number and playing time.

Repeated button presses will scrollthrough these displays.

CDNavigation units

Operation

Select the USB device as the audiosource by pressing the CD/AUX buttonuntil DEVICES appears in the display.Select DEVICESand then select USB fromthe available device list. After firstconnecting theUSBdevice, the first trackwithin the first folder will start to playautomatically. Subsequently, followingaudio source switching, the position ofplayback on the USB device isremembered.

To browse the device contents, press theSELECT button once.




• "<" to the left hand side of the displayindicates that a further level up isreadable.


To navigate theUSBdevice contents, usethe rotary scroll/select button to browsethrough lists. Push the button to expandthe contentswithin the highlighted playlistor folder, or to commence playback of aparticular track. Press ESC to go up onelevel.

Audio control

Press the SEEK up and down keys toskip backwards and forwards throughtracks.

Press and hold theSEEK keys to enablefast rewind/fast forward through trackcontent.

Rotate or press the SELECT button tobrowse the device contents.

Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists. Differentoptions may appear depending uponwhether or not a playlist is in operation.

216

Connectivity

Press the SCAN button to scan thecurrent playlist if it is in operation, or thecomplete USB device or folder.


• title

• artist

• album


DVDNavigation units

Operation

Select the USB device as the audiosource by pressing the CD/AUX buttonuntil the USB button appears to the left ofthe display. Select USB from the availabledevice list.

Note: Some devices may be shown butnot selectable, depending if the device isconnected or not.

After first connecting the USB device, thefirst track within the first folder will start toplay automatically. Subsequently, followingaudio source switching, the position ofplayback on the USB device isremembered.

To browse the device contents, press thescroll up or down arrow button.




• "<" to the left hand side of the displayindicates that a further level up isreadable.


To navigate theUSBdevice contents, usethe scroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist or folder, orto commence playback of a particulartrack. Press the left arrow key to go upone level.

Audio control



Press the scroll bar arrow keys to browsethe device contents.

Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists.

Press the SCAN button to scan thecurrent playlist if it is in operation, or thecomplete USB device or folder.


• title

• artist

• album


USINGAN IPOD

Various icons are used to identify typesof audio file, folders etc.

217

Connectivity

E100030

iPod is the active source

E100031

iPod playlist

E100032

iPod artist

E100033

iPod album

E100034

iPod genre

E100035

iPod song

E100036

iPod generic category

E100037

iPod generic media file

Sony radio

Operation

Select the iPod as the audio source byrepeatedly pressing theCD/AUX buttonuntil iPod appears in the display.

The iPodmenu list for browsing contentswill be available through the radio display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe up/down arrow key or the OK buttononce.


the display shows the current positionof the list view.

• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).


• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.

To navigate the iPod contents, use theup/downarrowkeys to scroll through lists,and the left/right keys to move up ordown within the hierarchy. Once yourdesired track, playlist, album, artist orgenre is highlighted, press the OK buttonto select playback.

Note: If you wish to jump to the top levelof the iPod contents, press and hold theleft arrow key.

Audio control

Press the left and right arrow keys to skipbackwards and forwards through tracks.

Press and hold the left/right arrow keysto enable fast rewind/fast forward throughtrack content.

Press the up/down arrow key or the OKbutton to browse the iPod contents.

Press theMENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.

Press the SCAN button to scan thecurrently selected tracks.

218

Connectivity

Press the INFO button to display thefollowing:• title

• artist


Repeated button presses will scrollthrough these displays.

CDNavigation units

Operation

Select the iPod as the audio source bypressing the CD/AUX button untilDEVICES appears in the display. SelectDEVICES and then select iPod from theavailable device list.

The iPodmenu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe SELECT button once.






To navigate the iPod contents, use therotary scroll/select button to browsethrough lists. Push the button to expandthe contentswithin the highlighted playlist,album, artist, genre or to commenceplayback of a particular track. Press ESCto go up one level.

Audio control



Rotate or press the SELECT button tobrowse the iPod contents.

Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.



• artist


DVDNavigation units

Operation

Select the iPod as the audio source bypressing the CD/AUX button until theiPod button appears to the left of thedisplay. Select iPod from the availabledevice list.

Note: Some devices may be shown butnot selectable, depending if the device isconnected or not.

219

Connectivity

The iPodmenu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standaloneuse (for example search by artist, title,etc.). To browse the iPod contents, pressthe scroll up or down arrow button.






To navigate the iPod contents, use thescroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist, album, artist,genre or to commence playback of aparticular track. Press the left arrow keyto go up one level.

Audio control



Press the scroll bar arrow keys to browsethe iPod contents.

Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possibleto enable the iPod "Shuffle songs" optiondirectly from the top level.



• artist


220

Connectivity

ROADSAFETY

WARNINGSThe system provides you withinformation designed to help youreach your destination quickly and

safely.

For reasons of safety, the drivershould only program the systemwhen the vehicle is stationary.

The system provides no assistancewith respect to stop signs, trafficlights, areas under construction or

other important safety information.

Do not use the system until youhave familiarised yourself with itsoperation.

Only view the system display whendriving conditions permit.

Safety information

Read and follow all stated safetyprecautions. Failure to do somay increaseyour risk of collision and personal injury.Ford Motor Company shall not be liablefor any damages of any type arising fromfailure to follow these guidelines.

If detailed viewing of route instructions isnecessary, pull off the roadwhen it is safeto do so and park your vehicle.

Do not use the navigation system tolocate emergency services.

To use the system as effectively andsafely as possible, always use the latestnavigation information. Your dealer will beable to assist with this.

221

Navigation introduction

GETTINGSTARTED

CAUTION


Note: Youwill be chargedwhen sendingand receiving text messages.

Note:Refer to your phone handbook forall phone functions and operation.

Note: Keep the activation code (printedon the installation guide) in a safe place.

Note:Retain the activation textmessagein your mobile phone inbox.

Compatibility of phones

CAUTION

As no common agreement exists,mobile phonemanufacturers are ableto implement a variety of profiles in

their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insomecasesmay significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.

Please visit the websitewww.ford-mobile-connectivity.com forfull details.

Installing themicro SDcard

1

2

E114212

1. Remove the micro SD card from theadaptor.

2. Insert the micro SD card into themobile phone.

Activating themobile phonenavigation system

Note: The radio must be switched onbefore connecting the mobile phone tothe in-car GPS receiver.

Note: The Ford Mobile Navigation mustbe installed and activated on your mobilephone.

Note: It is possible to activate up to amaximum of three phones.

Note: Detailed instructions are availableon the micro SD card and atwww.ford-mobile-connectivity.com.

1. Switch the radio on.

222

Navigation system

E114213

2. Switch yourmobile phoneon and startthe "Ford Mobile Navigation".

3. Choose "Select Destination".

4. Choose "Enter Address".

5. Change route options if necessaryand start the route guidance.

6. The vehicle display will show the turninformation. Voice instructions areheard via the vehicle speakers.

Note:Yourmobile phonewill display yourcurrent position.

7. You are able to exit the application andcontinue your route guidance afterrestarting the application.

223

Navigation system

TYPEAPPROVALS

FCC/INDUSTRYCANADANOTICE

This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.

FCC ID: WJLRX-42

IC: 7847A-RX42

Changes or modifications to your devicenot expressly approved by the partyresponsible for compliance can void theuser's authority to operate the equipment.

RX-42 - declaration ofconformity

We, the party responsible for compliance,declare under our sole responsibility thatthe Handset Integration product RX-42 isin conformity with the provisions of thefollowing Council Directive: 1999/5/EC. Acopy of theDeclaration of Conformity canbe found at:

www.novero.com/declaration_of_conformity

The Bluetooth word mark and logos areowned by the Bluetooth SIG, Inc. and anyuse of such marks by Ford MotorCompany is under license. Othertrademarks and trade names are thoseof their respective owners.

TYPEAPPROVALS

iPod is a trademark of Apple Inc.

TYPEAPPROVALS

E114214

© 2008 NAVTEQ B.V. All rights reserved.

224

Appendices

E114220

ELECTROMAGNETICCOMPATIBILITY

WARNINGSYour vehicle has been tested andcertified to European legislationsrelating to electromagnetic

compatibility (2004/104/EC). It is yourresponsibility to ensure that anyequipment you have fitted complies withapplicable local legislations. Have anyequipment fitted by properly trainedtechnicians.

WARNINGS

Radio frequency (RF) transmitterequipment (e.g. cellular telephones,amateur radio transmitters etc.)may

only be fitted to your vehicle if they complywith the parameters shown in the tablebelow. There are no special provisions orconditions for installations or use.

Do not mount any transceiver,microphones, speakers, or anyother item in the deployment path

of the airbag system.

Do not fasten antenna cables tooriginal vehicle wiring, fuel pipes andbrake pipes.

225

Appendices

WARNINGSKeep antenna and power cables atleast 100mm from any electronic

WARNINGSmodules and airbags.

E85998

6

7

1 2 3 8

4

5

AntennaPositionsMaximumoutput powerWatt(PeakRMS)

FrequencyBandMHz

3, 850 W1 – 30

2, 350 W30 – 54

1, 2, 3, 4, 550 W68 – 87.5

1, 2, 3, 4, 550 W142 – 176

1, 2, 3, 4, 550 W380 – 512

1, 2, 3, 4, 5 (61, 71)10 W (2 W1)806 – 940

210 W1200 – 1400

1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1710 – 1885

1, 2, 3, 4, 5 (61, 71)10 W (1 W1)1885 – 2025

All positions0.1 W2400 – 2500

1Only for GSM/3G cellular phones, with a patch antenna installed inside of the frontwindscreen.

226

Appendices

Note: After the installation of RFtransmitters, check for disturbances fromand to all electrical equipment in thevehicle, both in the standby and transmitmodes.

Check all electrical equipment:• with the ignitionON• with the engine running

• during a road test at various speeds.

Check that electromagnetic fieldsgenerated inside the vehicle cabin by thetransmitter installed donot exceedhumanexposure limits specified in EU directive2004/40/EC.

227

Appendices

228

AA/CSee: Climate control.....................................81

About this handbook................................5ABSSee: Brakes.................................................125

ABS driving hintsSee: Hints on driving with ABS.................125

AccessoriesSee: Parts and accessories..........................5

Adaptive front lighting system(AFS).......................................................49

Adjusting the steering wheel.................41Adjusting the windscreen washerjets...........................................................45

AFSSee: Adaptive front lighting system(AFS)...........................................................49

Air conditioningSee: Climate control.....................................81

Air vents.....................................................81Alarm.........................................................39Principle of operation...................................39

Appendices...........................................224Arming the alarm.....................................39Arming the engine immobiliser.............38Audible warnings and indicators...........67Automatic transmission...............................67Frost................................................................67Key-in-ignition...............................................68Key outside car.............................................67Lights on........................................................68Low fuel.........................................................68Seat belt reminder.......................................68

Audio control............................................41Mode..............................................................42Seek...............................................................42Volume............................................................41

Audio unit commands..........................195Auxiliary input...............................................201CD Changer.................................................196CD Player.....................................................195External devices - iPod.............................203External devices - USB..............................201Radio.............................................................198SD Card.......................................................204

Auto-dimming mirror..............................62

Autolamps................................................48Automatic climate control.....................84Air distribution...............................................86Blower............................................................85Mono mode..................................................85Recirculated air.............................................86Setting the temperature.............................85Switching off the automatic climatecontrol........................................................86

Switching the air conditioning on andoff................................................................86

To switch mono mode back on.................85To switch mono mode off...........................85Windscreen defrosting anddemisting...................................................86

Automatic transmission........................122Emergency park position releaselever..........................................................124

Manual shifting - Vehicles with a 4F27Etransmission............................................123

Selector lever positions.............................122Sportmode andmanual shifting - Vehicleswith a 6DCT450 transmission..............123

Autowipers...............................................43Auxiliary heater........................................87Diesel auxiliary heater (depending oncountry).....................................................90

Fuel operated heater (depending oncountry).....................................................90

Parking heater...............................................87Auxiliary input (AUX IN) socket............109Type 1............................................................109Type 2...........................................................109

Auxiliary power sockets.......................104Power inverter.............................................104

BBattery connection points.....................171Bluetooth setup.....................................188Handling of phones....................................188Requirements for Bluetoothconnection..............................................188

Bonnet lockSee: Opening and closing the bonnet.....152

Booster cablesSee: Using booster cables........................170

229

Index

Booster cushions.....................................19Booster cushion (Group 3)..........................19Booster seat (Group 2)................................19

Brake and clutch fluid check...............163Brakes.....................................................125Principle of operation.................................125

Bulb changingSee: Changing a bulb..................................52

Bulb specification chart..........................58

CCar washSee: Cleaning the exterior.........................168

Catalytic converter.................................119Driving with a catalytic converter..............119

CD changer............................................109Centre console......................................104Rear seat centre console..........................104

Changing a bulb......................................52Approach lamps...........................................55Central brake lamp......................................56Front direction indicators............................52Front fog lamps............................................54Front interior lamp........................................56Front reading lamps.....................................57Headlamp dipped beam.............................53Headlamp main beam.................................53Luggage compartment lamp.....................58Number plate lamp......................................56Rear lamps....................................................56Side lamps.....................................................53Side repeaters..............................................55Vanity mirror lamps.......................................57

Changing a fuse....................................143Changing a road wheel........................172Assembling the wheel brace....................174Installing a road wheel................................176Jacking and lifting points............................173Locking wheel nuts.....................................172Removing a road wheel.............................175Removing the wheel trim..........................175Vehicle jack..................................................172Vehicles with a temporary sparewheel........................................................172

Changing the remote controlbattery....................................................28Remote control with a folding keyblade..........................................................29

Remote control without a folding keyblade..........................................................30

Changing the wiper blades...................46Rear window wiper blades.........................46Windscreen wiper blades...........................46

Checking the wiper blades...................46Childminder mirror.................................109Child safety...............................................16Child safety locks....................................20Left-hand side...............................................21Right-hand side.............................................21

Child seat positioning..............................17Child seats................................................16Child restraints for different massgroups........................................................16

Cigar lighter............................................103Cleaning the exterior............................168Body paintwork preservation...................168Cleaning the chrome trim.........................168Cleaning the headlamps...........................168Cleaning the rear window.........................168

Cleaning the interior..............................168Instrument cluster screens, LCD screens,radio screens..........................................169

Seat belts.....................................................168Climate control.........................................81Principle of operation....................................81

Climate control commands.................210Climate.........................................................210

Coded keys.............................................38Cold weather precautions...................140Connecting an external device...........214Connection..................................................214

Connecting an external device -Vehicles With: Bluetooth....................214Connecting a Bluetooth audiodevice.......................................................214

Connectivity...........................................213General information....................................213

Convenience features..........................103Coolant checkSee: Engine coolant check.......................163

Cool box.................................................105

230

Index

Cruise control.........................................132Principle of operation.................................132

Cruise controlSee: Using cruise control..........................132

Cup holders............................................107Seat back trays...........................................107

DDetachable tow ball..............................136Driving with a trailer....................................138Inserting the tow ball arm..........................137Maintenance...............................................138Removing the tow ball arm.......................138Unlocking the tow ball armmechanism..............................................137

Diesel particulate filter (DPF).................116Regeneration...............................................116

Direction indicators.................................50Disabling the passenger airbag............26Disabling the passenger airbag.................27Enabling the passenger airbag..................27Fitting the passenger airbag deactivationswitch.........................................................27

Disarming the alarm................................40Vehicles with keyless entry.........................40Vehicles without keyless entry...................40

Disarming the engine immobiliser........38DPFSee: Diesel particulate filter (DPF).............116

Driving hints............................................140Driving through water...........................140Driving through water ...............................140

EElectric exterior mirrors...........................61Electric folding mirrors.................................62Mirror tilting positions...................................62

Electric seats...........................................95Electric sunroof.......................................90Opening and closing the sunroof...............91Opening and closing the sunroofautomatically..............................................91

Sunroof anti-trap protection.......................92Sunroof relearning........................................92Sunroof safety mode...................................92Tilting the sunroof..........................................91

Electric windows.....................................60Anti-trap function..........................................60Driver's door switches.................................60Global opening and closing........................60Opening and closing the windowsautomatically.............................................60

Resetting the memory of the electricwindows.....................................................61

Safety switch for rear windows.................60Electromagnetic compatibility............225Emergency equipment.........................141Engine compartment overview - 1.6LDuratec-16V (Sigma)/1.6LDuratec-16VTi-VCT (Sigma)....................................154

Engine compartment overview - 1.6LDuratorq-TDCi (DV) Diesel.................157

Engine compartment overview - 1.8LDuratec-HE (MI4)/2.0L Duratec-HE(MI4)......................................................156

Engine compartment overview - 1.8LDuratorq-TDCi (Lynx) Diesel.............159

Engine compartment overview - 2.0LDuratorq-TDCi (DW) Diesel...............160

Engine coolant check...........................163Checking the coolant level........................163Topping up...................................................163

Engine heater..........................................117Engine immobiliser..................................38Principle of operation...................................38

Engine oil check.....................................162Checking the oil level.................................162Topping up...................................................163

Engine oil dipstick - 1.6L Duratec-16V(Sigma)/1.6L Duratec-16V Ti-VCT(Sigma)..................................................161

Engine oil dipstick - 1.6L Duratorq-TDCi(DV) Diesel............................................162

Engine oil dipstick - 1.8L Duratec-HE(MI4)/2.0L Duratec-HE (MI4).............161

Engine oil dipstick - 1.8L Duratorq-TDCi(Lynx) Diesel.........................................162

Engine oil dipstick - 2.0L Duratorq-TDCi(DW) Diesel..........................................162

Exterior mirrors.........................................61Manual folding mirrors..................................61

231

Index

FFastening the seat belts........................24First aid kit................................................141Floor mats................................................111Fog lampSee: Front fog lamps...................................48

Front fog lamps.......................................48Fuel and refuelling..................................118Technical specifications.............................120

Fuel burning heaterSee: Auxiliary heater.....................................87

Fuel consumption..................................120Fuel consumptionSee: Technical specifications....................120

Fuel cut-off switch.................................142Vehicles with a Duratec engine................142

Fuel filler flap............................................119Fuel quality - Diesel................................118Long-term storage......................................119

Fuel quality - E85....................................118Long-term storage......................................118

Fuel quality - Petrol.................................118Fuse box locations................................143Engine compartment fuse box................143Passenger compartment fuse box.........143

Fuse labels..............................................143Fuses.......................................................143Fuse specification chart.......................145Engine compartment fuse box................145Passenger compartment fuse box.........147

GGauges.....................................................63Engine coolant temperature gauge..........64Fuel gauge.....................................................65

GearboxSee: Transmission.......................................122

General information on radiofrequencies............................................28

Getting started......................................222Activating the mobile phone navigationsystem.....................................................222

Compatibility of phones............................222Installing the micro SD card......................222

Glasses holder.......................................108

Global opening and closing...................36Global closing................................................37Global opening.............................................36

HHandbrakeSee: Parking brake.....................................125

Hazard warning flashers........................50Headlamp levelling..................................48Headlamp washers................................45Head restraints........................................94Adjusting the head restraint.......................94Removing the head restraint......................95

Heated seats..........................................101Heated windows and mirrors................87Heated exterior mirrors...............................87Heated windows..........................................87

HeatingSee: Climate control.....................................81

Hints on driving with ABS.....................125

IIgnition switch.........................................112ImmobiliserSee: Engine immobiliser..............................38

Information displays................................69General information.....................................69

Information messages...........................76Doors open....................................................77Keyless system.............................................77Lighting...........................................................78Maintenance.................................................78Message indicator........................................76Message symbols........................................76Power steering.............................................79Stability control (ESP)...................................80Transmission.................................................79Viewing current messages.........................77

Instrument lighting dimmer..................103Instruments..............................................63Interior lamps...........................................50Courtesy lamp..............................................50Reading lamps...............................................51Vanity mirror lamps.......................................51

Introduction................................................5

232

Index

ISOFIX anchor points..............................20Attaching a child seat with toptethers........................................................20

JJump startingSee: Using booster cables........................170

KKeyless entry...........................................34Disabled keys................................................36General information.....................................34Locking and unlocking the doors with thekey blade...................................................36

Locking the vehicle......................................34Passive key...................................................34Unlocking the vehicle...................................35

Keyless starting......................................115Failure to start..............................................115Ignition on.....................................................115Starting a diesel engine..............................115Starting with automatic transmission.......115Starting with manual transmission............115Stopping the engine...................................116

Keys and remote controls.....................28

LLighting control........................................47Headlamp flasher.........................................47Home safe lighting.......................................47Lighting control positions............................47Main and dipped beam...............................47Parking lamps................................................47

Lighting......................................................47Load carrying.........................................134General information....................................134

Locking and unlocking...........................32Automatic relocking.....................................33Central locking..............................................32Double locking..............................................32Double locking the doors with thekey..............................................................32

Locking and unlocking confirmation.........32Locking and unlocking the doors and theluggage compartment lid with theremote control..........................................32

Locking and unlocking the doors frominside..........................................................33

Locking and unlocking the doors with thekey..............................................................32

Luggage compartment lid..........................33Reprogramming the unlockingfunction......................................................34

Locks.........................................................32Luggage covers....................................134

MMaintenance..........................................152General information....................................152Technical specifications.............................165

Manual climate control...........................82Air conditioning.............................................83Air distribution control..................................82Blower............................................................82Heating the interior quickly.........................82Recirculated air.............................................82Ventilation......................................................83

Manual seats...........................................93Adjusting the angle of the seatback.........94Adjusting the height of the driver’sseat.............................................................94

Adjusting the lumbar support.....................94Moving the seats backwards andforwards....................................................93

Manual transmission.............................122Message centreSee: Information displays............................69

MirrorsSee: Heated windows and mirrors............87See: Windows and mirrors.........................60

233

Index

NNavigation introduction........................221Navigation system commands...........210Navigation system................................222

OOccupant protection..............................22Principle of operation...................................22

Oil checkSee: Engine oil check.................................162

See: Opening and closing the bonnet.....152

OOpening and closing the bonnet........152Closing the bonnet.....................................153Opening the bonnet...................................152

PParking aid..............................................127Principle of operation.................................127

Parking aidSee: Using the parking aid.........................127

Parking brake.........................................125All vehicles....................................................125

Parts and accessories..............................5Look for the Ford logo on the followingparts .............................................................6

Now you can be sure that your Ford partsare Ford parts.............................................5

Personalised settings.............................74Chime deactivation......................................76Clock setting.................................................74ESP.................................................................74Help screen and navigationinformation................................................74

Language setting.........................................75Navigation information.................................75Steering..........................................................74Units of measure..........................................75

Power steering fluid check..................164All except vehicles with 1.6L Duratec-16V(Sigma) or 1.6L Duratec-16V Ti-VCT(Sigma) engine........................................164

Vehicles with 1.6L Duratec-16V (Sigma) or1.6L Duratec-16V Ti-VCT (Sigma)engine......................................................164

Programming the remote control........28Programming a new remote control........28Reprogramming the unlockingfunction......................................................28

QQuick start..................................................8Adjusting the steering wheel.......................12Airbag..............................................................10Autolamps......................................................13Automatic climate control...........................14Automatic transmission...............................15Autowipers.....................................................13Diesel particulate filter (DPF).......................15Engine idle speed after starting..................15Instrument panel overview...........................8Keyless entry..................................................11Keyless starting.............................................15Locking and unlocking..................................11Manual climate control.................................13Manual transmission.....................................15Opening the bonnet.....................................15Rear seats......................................................14

RRear fog lamps........................................48Rear seats................................................96Comfort seat system...................................96Folding the seatbacks forward..................97Folding the seats forward...........................98Installing the seats.......................................101Removing the seats...................................100Returning the seatbacks to the uprightposition......................................................98

Returning the seats to the seatingposition......................................................99

Rear under floor storage......................135Rear view camera.................................129Principle of operation.................................129

234

Index

Rear window wiper and washers.........44Intermittent wipe..........................................44Rear window washer...................................45Reverse gear wipe.......................................44

Refuelling - E85......................................120Refuelling.................................................119Remote control batterySee: Changing the remote controlbattery........................................................28

Remote control programmingSee: Programming the remote control.....28

Removing a headlamp............................51Repairing minor paint damage............169Road Safety............................................221Safety information......................................221

Running-in..............................................140Brakes and clutch.......................................140Engine...........................................................140Tyres.............................................................140

SSafety precautions.................................118Satellite navigation unit holder..............110Adjusting the holder....................................110Fitting the navigation unit...........................110Removing the navigation unit.....................111

Seat belt height adjustment..................25Seat belt reminder..................................26Deactivating the seat belt reminder..........26

Seats.........................................................93Sitting in the correct position.................93Snow chainsSee: Using snow chains.............................181

Speed controlSee: Cruise control.....................................132

Stability control.......................................126Principle of operation.................................126

Stability controlSee: Using stability control........................126

Starter switchSee: Ignition switch.....................................112

Starting a diesel engine.........................114Cold or hot engine......................................114

Starting a petrol engine - E85..............113Starting at low ambient temperatures....................................................................114

Starting a petrol engine.........................112Cold or hot engine......................................113Engine idle speed after starting................113Flooded engine............................................113

Starting the engine.................................112General information....................................112

Status after a collision...........................142Steering wheel lock...............................112Vehicles with keyless starting....................112Vehicles without keyless starting..............112

Steering wheel.........................................41Storage compartments........................106Driver’s seat storage bin............................107Front centre console storagecompartment..........................................106

Front storage compartment.....................106Rear centre console storagecompartment..........................................107

Storage area under the rear centreseat...........................................................107

Sun blinds...............................................103Panoramic roof...........................................103

SunroofSee: Electric sunroof....................................90

Switching off the engine........................117Vehicles with a turbocharger.....................117

Symbols glossary......................................5Symbols in this handbook.............................5Symbols on your vehicle...............................5

TTechnical specifications........................184Technical specifications.............................184

Telephone commands........................206Create a phonebook.................................208Main settings...............................................210Phone..........................................................206Phone functions.........................................206

Telephone controls...............................189Remote control...........................................189

Telephone setup....................................187Bond another Bluetooth phone...............188Making a phone an active phone............187Phonebook..................................................187Phonebook categories..............................187

Telephone...............................................187General information....................................187

235

Index

TelephoneSee: Using the telephone - Vehicles With:Navigation System.................................192

See: Using the telephone - VehiclesWithout:Navigation System.................................189

Toll reader...............................................108Towing a trailer.......................................136Steep gradients..........................................136

Towing points.........................................150Installing the towing eye............................150Towing eye location...................................150

Towing the vehicle on four wheels......151All vehicles....................................................151Vehicles with automatictransmission.............................................151

Towing.....................................................136Transmission..........................................122Trip computer..........................................72Type 2 and 3.................................................72

Type approvals......................................224FCC/INDUSTRY CANADA NOTICE.........224RX-42 - declaration of conformity..........224

Tyre care.................................................180Tyre pressuresSee: Technical specifications.....................181

Tyre repair kit..........................................177Checking the tyre pressure......................179General information....................................177Inflating the tyre...........................................178Using the tyre repair kit..............................177

TyresSee: Wheels and tyres...............................172

UUSB port..................................................110Using an iPod.........................................217CD Navigation units....................................219DVD Navigation units..................................219Sony radio....................................................218

Using a USB device...............................215CD Navigation units....................................216DVD Navigation units..................................217Sony radio....................................................215

Using booster cables............................170To connect the booster cables................170To start the engine......................................170

Using cruise control..............................132Cancelling the set speed..........................133Changing the set speed............................132Resuming the set speed...........................133Setting a speed...........................................132Switching cruise control off.......................133Switching cruise control on.......................132

Using seat belts during pregnancy......26Using snow chains.................................181Vehicles with stability control (ESP)..........181

Using stability control............................126Using the parking aid............................127Manoeuvring with the parking aid............127Switching the parking aid on and off.......127

Using the rear view camera.................129Activating the rear view camera..............129Deactivating the rear view camera..........131Using the display.........................................129Vehicles with parking aid............................131

Using the telephone - Vehicles With:Navigation System..............................192Changing the active phone......................193Debonding a bonded phone....................193Making a call................................................192Muting the microphone.............................192Receiving an incoming call........................192Receiving a second incoming call............192

Using the telephone - VehiclesWithout:Navigation System..............................189Changing the active phone.......................191Debonding a bonded phone.....................191Debonding a bonded phone - Sonyradio...........................................................191

Making a call................................................189Muting the microphone..............................191Receiving an incoming call........................190Receiving a second incoming call............190

Using voice control...............................194Name tag.....................................................195System operation.......................................194

Using winter tyres..................................181

VVehicle battery.......................................170Vehicle care............................................168Vehicle identification number(VIN).......................................................183

236

Index

Vehicle identification plate....................183Vehicle identification..............................183Vehicle recovery....................................150VentilationSee: Climate control.....................................81

VentsSee: Air vents.................................................81

VINSee: Vehicle identification number(VIN)..........................................................183

Voice control............................................42Principle of operation.................................194

WWarning lamps and indicators..............65ABS warning lamp........................................65Airbag warning lamp....................................65Brake system lamp......................................65Cruise control indicator...............................65Direction indicators......................................65Doors open warning lamp..........................65Engine warning lamp...................................66Front fog lamp indicator..............................66Frost warning lamp......................................66Glow plug indicator......................................66Headlamp indicator......................................66Ignition warning lamp...................................66Low fuel level warning lamp.......................66Main beam indicator....................................66Message indicator.......................................66Oil pressure warning lamp..........................66Power steering warning lamp....................67Rear fog lamp indicator...............................67Seat belt reminder........................................67Shift indicator.................................................67Stability control (ESP) indicator..................67

Warning triangle......................................141Washer fluid check................................164WashersSee: Wipers and washers...........................43

WashingSee: Cleaning the exterior.........................168

Wheels and tyres...................................172General information....................................172Technical specifications..............................181

Windows and mirrors.............................60Windscreen washers.............................44

Windscreen wipers.................................43Automatic wiper system.............................43Intermittent wipe..........................................43

Winter tyresSee: Using winter tyres...............................181

Wipers and washers...............................43

237

Index

238

Feel the difference

AM5J-19A321-BDA(CG3478en)

Documents

C-MAX(CG3478en)09-2009